HandA-Accessories.com

Accessory

INSTALLATION INSTRUCTIONS

Application

DVD in-VEHICLE ENTERTAINMENT SYSTEM WITH SUNROOF

Publications No.

AII 28609 RIDGELINE

Issue Date

FEB 2005

PARTS LIST Attachment Kit: P/N 08B23-SJC-100

DVD player bracket A

i-VES harness

DVD player bracket B

DIN cable “A” FM modulator bracket

DIN cable “B”

Template: without sunroof (Not used.)

Interior light harness Template: with sunroof

Sub-feeder cord Template A

Monitor gasket

Template B

2 Screws, 3 x 8 mm

Monitor bracket Washer-screw, 5 x 12 mm

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

08B23-SJC-1000-9A

1 of 26

2 Washer-screws, 5 x 16 mm

Monitor Kit (sold separately): P/N 08A23-2G1-010

Monitor console 2 Washer-screws, 5 x 25 mm

4 Washer-screws, 6 x 12 mm (Not used.)

DVD player

4 Stepped bolts, 5 mm

4 Square-head bolts

2 Headphones

4 Flange nuts, 4 mm Remote controller Flange nut, 5 mm

2 Cap nuts, 5 mm

FM modulator

2 Nuts, 3 mm Connector clip

4 Washer-screws, 5 x 8 mm

18 Wire ties

2 Screw caps

Long wire tie

Quick Reference Tag

10 Cushion tapes

Owner’s Manual

7 EPT sealers

2 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

INSTALLATION

TOOL AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Utility knife Scissors Push-pin Isopropyl alcohol Shop towel Tape measure Drill 3 mm and 8 mm Drill bits 1-1/8" (28 mm) Hole saw Ratchet 5 mm, 8mm, and 10 mm Combination wrenches 8 mm, 10 mm, and 14 mm Sockets Tape Masking tape Torque wrench T25 Torx wrench Diagonal cutters Eye protection (face shield, safety goggles, etc.)

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.

Make sure you have the anti-theft code for the radio, then write down the radio station presets.

2.

Close the sunroof.

3.

Disconnect the negative cable from the battery.

4.

Insert a flat-tip screwdriver wrapped with a shop towel into the groove of the instrument panel and release two clips. Pull the instrument panel out toward you to release eighteen clips, and remove the instrument panel by unplugging the vehicle connectors. VEHICLE CONNECTOR

VEHICLE CONNECTOR

Illustration of the DVD i-VES installed in the Vehicle INSTRUMENT PANEL DIN CABLE “A” MONITOR CONSOLE

VEHICLE CONNECTOR

SHOP TOWEL

CLIPS (2) CLIPS (18) INTERIOR LIGHT HARNESS

i-VES HARNESS DIN CABLE “B”

FLAT-TIP SCREWDRIVER Insert into the groove.

3915101T

DVD PLAYER 4917091H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

3 of 26

5.

Remove the audio unit (five screws, and pull the audio unit out toward you, and unplug the vehicle connectors).

6.

Remove the driver’s console side trim (three retaining clips and one tab).

Without Navi

VEHICLE CONNECTOR

INSTRUMENT PANEL

AUDIO UNIT

TAB DRIVER’S CONSOLE SIDE TRIM

SCREWS (5)

RETAINING CLIPS (3)

3915010T

4606030T

7.

With Navi

VEHICLE CONNECTOR

INSTRUMENT PANEL

Remove the passenger’s console side trim (two retaining clips and one tab).

NAVIGATION UNIT

TAB

SCREWS (5) 4913010H

4 of 26

AII 28609 (0502)

RETAINING CLIPS (2)

PASSENGER’S CONSOLE SIDE TRIM

3915020T

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

8.

Remove the dashboard center lower cover:

9.

•

Remove the center pocket.

•

Remove the three self-tapping screws.

•

Release the five retaining clips and six retaining tabs, and pull out the dashboard center lower cover.

•

Unplug the vehicle connectors, and remove the dashboard center lower cover.

Remove the glove box: •

Open the glove box. Disconnect the damper arm.

•

Remove the stoppers (two retaining tabs for each stopper).

•

Remove the two screws. RETAINING TABS (2)

STOPPERS (2)

DAMPER ARM

VEHICLE CONNECTOR RETAINING CLIPS (3)

RETAINING TABS (6) SCREW

SELFTAPPING SCREWS (3)

SCREW GLOVE BOX

RETAINING CLIPS (2)

DASHBOARD CENTER LOWER COVER

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

CENTER POCKET

4606041T

3915034T

AII 28609 (0502)

5 of 26

10. Remove the right dashboard side cover (seven clips).

12. Remove the center console rear cover :

CLIPS (7)

•

Pull the center console rear cover out toward you to release eight clips.

•

Slide the vehicle console light connector and the vehicle connector, and remove the vehicle console light connector and the vehicle connector from the vehicle clips.

•

Unplug the vehicle console light connector and the vehicle connector.

VEHICLE CLIP VEHICLE CONSOLE LIGHT CONNECTOR

RIGHT DASHBOARD SIDE COVER

CLIPS (8)

4D09040H

11. Remove the front center tray (two clips and two hooks). HOOK CENTER TRAY

FRONT

CLIPS (2)

CENTER CONSOLE REAR COVER VEHICLE CONNECTOR

VEHICLE CLIP

4907020H

6 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

13. Remove the vehicle console light and harness (two retaining tabs).

15. Remove the right front door sill trim (three clips and three retaining tabs).

RETAINING TABS (2)

RETAINING TAB RIGHT FRONT DOOR SILL TRIM

CLIPS (3)

RETAINING TAB

VEHICLE CONSOLE LIGHT VEHICLE CONSOLE LIGHT HARNESS FRONT CENTER CONSOLE

4D09050H 4913031H

16. Remove the right rear door sill trim (three clips and three retaining tabs).

14. Remove the center console (two bolts and two self-tapping screws).

RETAINING TAB

RIGHT REAR DOOR SILL TRIM

SELF-TAPPING SCREW

RETAINING TAB

CLIPS (3)

CENTER CONSOLE

FRONT BOLTS (2)

4D10010H 4907012H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

7 of 26

17. Pull away the weatherstrip from the B-pillar lower trim panel. Remove the right seat belt lower anchor bolt cover and remove the right seat belt lower anchor bolt. Remove the right B-pillar lower trim panel by pulling it out toward you as shown.

19. Remove the right rear grab rail screw covers (two retaining tabs for each cover). Remove the right rear grab rail (two screws). B-PILLAR UPPER TRIM PANEL FRONT

WEATHERSTRIP (Pull away.) FRONT

RIGHT REAR GRAB RAIL RIGHT B-PILLAR LOWER TRIM PANEL

SCREWS (2)

SCREW COVERS (2) RETAINING TABS (2) LOWER ANCHOR BOLT COVER RIGHT SEAT BELT LOWER ANCHOR BOLT

4D10020H

20. Pull away the weatherstrip from the right B-pillar upper trim panel. Remove the right B-pillar upper trim panel (two clips).

18. Remove the right seat belt upper anchor bolt cover (four retaining tabs). Remove the right front seat belt upper anchor bolt. RETAINING TABS (2)

4D10060H

CLIPS (2)

WEATHERSTRIP (Pull away.) FRONT

RIGHT SEAT BELT UPPER ANCHOR BOLT COVER RETAINING TABS (2)

FRONT

Pry out on both tabs. SMALL FLAT-TIP SCREW DRIVER

RIGHT SEAT BELT UPPER ANCHOR BOLT COVER

RIGHT SEAT BELT UPPER ANCHOR BOLT

8 of 26

RIGHT B-PILLAR UPPER TRIM PANEL

4D10030H

4D10050H

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

21. Remove the right rear hook trim cover (four tabs). Remove the right rear hook trim (two self-tapping screws). RIGHT REAR HOOK TRIM COVER

23. Pull away the weatherstrip away from the passenger’s A-pillar. Remove the passenger’s A-pillar trim (two clips). CLIPS (2) PASSENGER’S A-PILLAR TRIM

RIGHT REAR HOOK TRIM

TABS (4)

SELF-TAPPING SCREW WEATHERSTRIP (Pull away.) 4703032T

FRONT 4D10040H

24. Remove the left and right lenses from the roof console (four retaining tabs for each lens).

22. Remove the passenger’s grab rail screw covers (two retaining tabs for each cover), then remove the passenger’s grab rail (two screws).

ROOF CONSOLE

RIGHT LENS

LEFT LENS SCREW COVER

RETAINING TABS (4)

RETAINING TAB SCREW COVER

4216040K

SCREW

PASSENGER’S RETAINING SCREW GRAB RAIL TAB

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

RETAINING TABS (4)

4703023T

AII 28609 (0502)

9 of 26

25. Open the console pocket lid and remove the four bolts. Unplug two vehicle connectors, and remove the roof console.

27. Remove the right sunvisor screw cover (four retaining tabs), and remove the right sunvisor (two torx screws and unplug the vehicle connector).

VEHICLE CONNECTOR

VEHICLE CONNECTOR RETAINING TABS (4)

ROOF CONSOLE

RIGHT SUNVISOR

CONSOLE POCKET

T25 TORX SCREW

SUNVISOR SCREW COVER

4703051T

BOLT

28. Using scissors, cut out the marked area from the template (with sunroof). Crease the template as shown.

4216050K

26. Remove the sunvisor holders by rotating them clockwise.

Cut out areas.

TEMPLATE (Crease.)

SUNVISOR HOLDERS (2)

4N03061H

4217011K

FLAT-TIP SCREWDRIVER

10 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

29. Open the sunshade. Position the template on the headliner and align the cutout with the sunshade knob. Tape the template to the headliner using strips of masking tape.

31. Close the sunshade.

SUNSHADE (Close.)

NOTE: Template is positioned with sunroof closed and sunshade open. REAR INTERIOR LIGHT

TEMPLATE FRONT

MASKING TAPE

FRONT 4N03091H

SUNSHADE (Open.)

32. Using a utility knife, cut out the marked area of the headliner. SUNSHADE KNOB

MARK

HEADLINER Align the crease with the edge. 4N03071H

UTILITY KNIFE

30. Using a felt-tip pen, mark the headliner along the outer edges of the template. Remove the template.

TEMPLATE FRONT

HEADLINER

HEADLINER Cut out this area.

4N03101H

FELT-TIP PEN

FRONT 4N03081H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

11 of 26

33. Gently pull the headliner down to release three clips and five velcro fasteners. VELCRO FASTENERS (5)

35. Route the yellow label side of DIN cable “A” along the vehicle harness, and temporarily secure DIN cable “A” to the vehicle harness with one wire tie.

CLIPS (3)

WIRE TIE (Loosely fasten)

EPT SEALER Cut in half.

VEHICLE CLIP

VEHICLE HARNESS YELLOW LABEL

DIN CABLE “A”

350 mm

4915014H

HEADLINER 4913101H

34. Route DIN cable “A” up through the headliner from the passenger's A-pillar, and out through the opening in the headliner you made in step 32.

DIN CABLE “A” TERMINAL 250 mm

36. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Using scissors, cut one EPT sealer in half. Wrap the EPT sealer half to DIN cable “A” in the area shown. 37. Route DIN cable “A” down behind the dashboard and towards the glove box opening. PASSENGER’S A-PILLAR OPENING

HEADLINER OPENING

DIN CABLE “A”

FRONT

12 of 26

YELLOW LABEL

VEHICLE FRAME

4913123H

AII 28609 (0502)

GLOVE BOX OPENING

DIN CABLE “A” 4D10070H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

38. Inside the glove box opening, route DIN cable “A” along the vehicle harness and towards the driver’s side of the vehicle.

Routing the i-VES Harness and the DIN Cables 40. At the audio unit opening, route the i-VES harness and the white label end of DIN cable “B” along the vehicle harness from the audio unit opening toward the floor of the vehicle .

VEHICLE HARNESS

i-VES HARNESS

AUDIO UNIT OPENING GLOVE BOX OPENING

DIN CABLE “A”

VEHICLE FRAME

4D10080H

39. Route DIN cable “A” to the audio unit opening, and down towards the floor vehicle.

WHITE LABEL DIN CABLE “B”

AUDIO UNIT OPENING

DIN CABLE “A”

4915035H

CENTER LOWER COVER OPENING

41. Route the i-VES harness, DIN cable “A” and DIN cable “B” toward the rear of the vehicle.

VEHICLE HARNESS DIN CABLE “A”

4D10090H

DIN CABLE “B”

i-VES HARNESS

VEHICLE FRAME DIN CABLE “A”

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

4915044H

13 of 26

42. Slide the center console cup holder forward, and slide the inner cover forward. Open the console cover.

45. To the prevent drilling through the inner panel, wrap tape around the end of a 3 mm and an 8 mm drill bit about 15-20 mm away from the tip. CENTER CONSOLE

CONSOLE COVER

MARK

INNER COVER

15-20 mm DRILL BIT (3 mm 8 mm)

CENTER CONSOLE

DRILL BIT

TAPE (Wrap tape around the drill bit)

DRILL 4915070H

CUP HOLDER 4915050H

43. Position template A on the center console at the location shown, and attach template A to the center console using strips of tape.

46. While wearing eye protection, drill an 8 mm hole at each marked point. Start with a 3 mm drill bit and finish with an 8 mm drill bit. Remove any burrs from each hole. 47. Position template B on the center console at the location shown, and tape the template to the center console.

TEMPLATE A

PUSH-PIN

MARKS (3) TAPE TAPE TEMPLATE B CENTER CONSOLE

PUSH-PIN

4915060H

CENTER CONSOLE

44. Using a push-pin, mark the center console at the marks on the template. Remove the template.

4915080H

48. Using a push-pin, mark the center console at the marks on the template. Remove the template.

14 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

49. While wearing eye protection, drill an 8 mm hole at each marked point. Start with a 3 mm drill bit and finish with an 8 mm drill bit. Use the drill bit with the tape attached.

52. Plug in the vehicle connectors, and install the vehicle connector in the vehicle clip. Route the vehicle console light harness through the console light opening.

HOLE SAW VEHICLE CONSOLE LIGHT HARNESS DRILL CONSOLE LIGHT OPENING

DRILL BIT (3 mm 8 mm) 1-1/8" (28 mm) HOLE SAW

CENTER CONSOLE CENTER CONSOLE REAR COVER

MARKS (3) CENTER CONSOLE 4915091H

50. Using a 1-1/8" (28 mm) hole saw, enlarge the center 8 mm hole to 1-1/8" (28 mm). Remove any burrs from each hole. 51. Reposition the center console in place. Route the i-VES harness, and DIN cables “A” and “B” through the 28 mm hole.

VEHICLE CONNECTOR

VEHICLE CLIP

Installing the DVD Player 53. Slide the DVD player into DVD player bracket A.

DVD PLAYER

i-VES HARNESS DIN CABLE “B”

DVD PLAYER BRACKET A DIN CABLE “A”

CENTER CONSOLE

28 mm HOLE

4915101H

AUXILIARY INPUT JACKS 4909020H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

15 of 26

54. Secure the auxiliary input jacks from the DVD player to DVD player bracket B with two 3 x 8 mm screws and two 3 mm nuts.

56. Install the vehicle console light to DVD player bracket A as shown.

VEHICLE CONSOLE LIGHT HARNESS

3 mm NUT

DVD PLAYER BRACKET A

AUXILIARY INPUT JACKS

3 x 8 mm SCREW

VEHICLE CONSOLE LIGHT

VEHICLE CONSOLE LIGHT

DVD PLAYER BRACKET B

4909030H

55. Secure DVD player bracket B to DVD player bracket A with one 5 x 12 mm washer-screw and one 5 mm flange nut. DVD PLAYER BRACKET A

RETAINING TABS (2)

DVD PLAYER BRACKET A

4909051H

57. Secure the DVD player to DVD player bracket A and B with three 5 x 8 mm washer-screws included with the Monitor Kit.

5 mm FLANGE NUT

CONNECTOR CLIP

DVD PLAYER BRACKET A CENTER CONSOLE LIGHT CONNECTOR DVD PLAYER BRACKET B

DVD PLAYER BRACKET B

5 x 12 mm SCREW

4909040H

5 x 8 mm WASHERSCREWS (3) (Included with the Monitor Kit.)

CONNECTOR CLIP

4909062H

58. Install the connector clip to the vehicle console light connector, and secure the vehicle console light connector to DVD player bracket B.

16 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

59. Slide the DVD player into the center console.

61. Secure DVD player bracket A to the center console with two 5 mm stepped bolts and two 5 mm cap nuts.

DVD PLAYER 5 mm CAP NUTS (2)

CENTER CONSOLE

5 mm STEPPED BOLTS (2) 4915141H

CENTER CONSOLE DVD PLAYER BRACKET A

60. Plug the i-VES harness 4-pin connector, DIN cable “A” and “B” and the vehicle console light connector into the rear of the DVD player.

4916020H

62. Lift the center console as shown, and secure DVD player bracket A to the center console with two 5 mm stepped bolts.

CONSOLE LIGHT CONNECTOR DVD PLAYER

8 mm HOLE

i-VES HARNESS 4-PIN CONNECTOR CENTER CONSOLE

DIN CABLE “B” YELLOW LABEL DIN CABLE “A”

4916013H

FRONT

5 mm STEPPED BOLT

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

4916030H

17 of 26

63. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Lift the center console, then secure the i-VES harness and the DIN cables to the vehicle panel with two cushion tapes as shown.

66. Secure the i-VES harness and the DIN cables to the vehicle harness with two wire ties in the areas shown.

CENTER CONSOLE

FRONT

VEHICLE HARNESS

WIRE TIE FRONT

i-VES HARNESS VEHICLE PANEL

CUSHION TAPE

DIN CABLE “B”

CUSHION TAPE DIN CABLE “A”

DIN CABLE “A”

DIN CABLE “B” VEHICLE BRACKET

4916041H

i-VES HARNESS

4916062H

67. At the audio unit opening, secure the i-VES harness and DIN cable “B” to the vehicle harness with one wire tie in the area shown. i-VES HARNESS

64. Reinstall the center console. 65. Pull back the floor carpet. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Secure the i-VES harness and the DIN cables to the vehicle panel with two cushion tapes as shown.

DIN CABLE “B”

AUDIO UNIT OPENING

VEHICLE HARNESS

WIRE TIE

FRONT

CUSHION TAPE

VEHICLE PANEL

FLOOR CARPET (Pull back.) 4D26011H

i-VES HARNESS

CUSHION TAPE DIN CABLE "A" DIN CABLE "B"

18 of 26

4916052H

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

68. At the audio unit opening, plug the i-VES harness 20-pin connector into the vehicle 20-pin connector, and secure the 20-pin connectors with one long wire tie. i-VES HARNESS 20-PIN CONNECTOR

LONG WIRE TIE

70. Secure DIN cable “A” to the vehicle harness with two wire ties in the areas shown. AUDIO UNIT OPENING WIRE TIE

AUDIO UNIT OPENING

DIN CABLE “B”

VEHICLE HARNESS

i-VES HARNESS

DIN CABLE “A”

VEHICLE 20-PIN CONNECTOR 4916070H

4D13040H

71. At the glove box opening, secure DIN cable “A” to the vehicle harness with three wire ties.

69. Secure the i-VES harness and DIN cable “B” to the vehicle harness with two wire ties in the areas shown.

VEHICLE HARNESS

WIRE TIE

GLOVE BOX OPENING WIRE TIE

DIN CABLE “A”

4D13050H

DIN CABLE “B” VEHICLE HARNESS

i-VES HARNESS 4916080H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

19 of 26

72. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Secure DIN cable “A” to the vehicle panel with one cushion tape. VEHICLE CLIP

75. Route the interior light harness between the headliner and insulator from the interior light opening out the headliner opening.

INTERIOR LIGHT HARNESS

WIRE TIE (2)

VEHICLE HARNESS

INSULATOR

DIN CABLE “A”

INTERIOR LIGHT OPENING

HEADLINER DIN CABLE “A” CUSHION TAPE

HEADLINER OPENING VEHICLE PANEL

VEHICLE 3-PIN CONNECTOR

WIRE TIE (Fasten securely)

VEHICLE FRAME

INTERIOR LIGHT HARNESS 3-PIN CONNECTOR

4916102H

FRONT

73. Secure DIN cable “A” to the vehicle harness with two wire ties, and tighten the wire tie you temporarily secured to DIN cable “A” in step 35.

76. Plug the interior light harness 3-pin connector into the vehicle 3-pin connector.

74. Remove the rear interior light. •

Remove the two lenses (four tabs on each lens).

•

Remove the two self-tapping screws.

•

Unplug the vehicle 3-pin connector.

4916122H

77. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Using scissors, cut one cushion tape in half. Secure the interior light harness to the headliner with the cushion tape half.

VEHICLE 3-PIN CONNECTOR

INTERIOR LIGHT OPENING CUSHION TAPE Cut in half. REAR INTERIOR LIGHT

CUSHION TAPE

HEADLINER OPENING

SELF-TAPPING SCREWS (2) TABS (4)

FRONT

FRONT

LENS

FOAM INTERIOR LIGHT HARNESS HEADLINER 3-PIN CONNECTOR

4916111H

78. Position the 3-pin connector in the cavity in the headliner. Reinstall the rear interior light.

20 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

79. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Using scissors, cut three cushion tapes in half. Secure DIN cable “A” to the headliner with the six pieces of cushion tape.

81. With the sunshade in the closed position, insert four square-head bolts through the holes in the vehicle frame. VEHICLE FRAME HEADLINER OPENING

CUSHION TAPES (3) Cut in half. 250 mm

HEADLINER OPENING

SQUARE-HEAD BOLTS (4) FRONT 4N03121H

DIN CABLE “A” FRONT 4916161H

82. Secure the monitor bracket to the vehicle frame with four 4 mm flange nuts and the four squarehead bolts you inserted.

Installing the Monitor Console 80. Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealers will attach. Using scissors, cut two EPT sealers in half. Attach the EPT sealer halves, and one EPT sealer to the monitor bracket in the areas shown. Cut the excess off the EPT sealers.

VEHICLE FRAME

SQUARE-HEAD BOLTS (4)

MONITOR BRACKET

EPT SEALERS (2) Cut in half.

EPT SEALER Cut off. SQUARE-HEAD BOLTS (4)

FRONT MONITOR BRACKET

4 mm FLANGE NUT

4N03141H

Cut off. 4N03111H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

21 of 26

83. Remove the left and right lenses from the monitor console, then install the monitor gasket on the console while aligning the mark of the monitor gasket with the mark on the monitor console. MONITOR CONSOLE

85. While holding the monitor console, secure the 3-pin connector and the terminal to the back of the monitor console with one cushion tape.

LEFT LENS FRONT

RIGHT LENS

3-PIN CONNECTOR

MONITOR CONSOLE TERMINAL

MONITOR GASKET

MARK 2326290T

84. Remove the tape that secures the 3-pin connector to the monitor console. Connect the interior light harness 3-pin connector and DIN cable “A” terminal into the monitor console 3-pin connector and monitor console terminal.

DIN CABLE “A” TERMINAL

INTERIOR LIGHT 3-PIN CONNECTOR

TAPE

MONITOR CONSOLE TERMINAL

CUSHION TAPE 4917041H

86. Position the monitor console on the monitor bracket, and install two 5 x 16 mm washer-screws and two 5 x 25 mm washer-screws. Install two screw caps, then reinstall the left and right lenses. Do not pinch the DIN cable “A” between the monitor console and monitor bracket.

MONITOR CONSOLE HARNESS

MONITOR CONSOLE

MONITOR BRACKET

5 x 25 mm WASHER SCREW MONITOR CONSOLE 3-PIN CONNECTOR FRONT

MONITOR CONSOLE

4N03151H

LEFT LENS

FRONT

22 of 26

AII 28609 (0502)

RIGHT LENS

5 x 16 mm WASHER SCREW SCREW CAPS (2)

4D21020H

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

87. Secure the FM modulator bracket to the FM modulator with one 5 x 8 mm washer-screw included with the monitor kit. FM MODULATOR

89. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Attach one EPT sealer half that you cut into two in step 88 to the audio unit/navigation unit.

FM MODULATOR BRACKET

Without Navi

AUDIO UNIT

5 x 8 mm WASHER-SCREW (Included with the monitor kit.) 4917021M

88. Set the FM modulator switch at 88.5. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Using scissors, cut one EPT sealer in half. Secure the FM modulator cables to the FM modulator with one EPTsealer half.

EPT SEALER Cut in half in step 88.

4917030M

SWITCH

EPT SEALER Cut in half.

With Navi NAVIGATION UNIT

FM MODULATOR

FM MODULATOR CABLE

4917052M

EPT SEALER Cut in half in step 88. 4917040M

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

23 of 26

90. Remove two screws from the audio unit/navigation unit. Secure the FM modulator bracket to the audio unit/navigation unit with the two screws you removed.

91. Plug the sub-feeder antenna leads into the FM modulator antenna leads. Plug the sub-feeder 2-pin connector into the audio unit/navigation unit.

Without Navi

Without Navi AUDIO UNIT FM MODULATOR ANTENNA LEAD

AUDIO UNIT

FM MODULATOR BRACKET

FM MODULATOR

SUB-FEEDER 2-PIN CONNECTOR

SCREW SUB-FEEDER ANTENNA LEAD

4917060M

4917080M

With Navi

With Navi

2-PIN CONNECTOR LOCATION

NAVIGATION UNIT

FM MODULATOR BRACKET

FM MODULATOR ANTENNA LEAD NAVIGATION UNIT

FM MODULATOR

SCREW

SUB-FEEDER 2-PIN CONNECTOR SUB-FEEDER ANTENNA LEAD

4917070M

4917090M

24 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

92. Using scissors, cut two EPT sealers in half. Wrap the two half EPT sealer halves around the respective antenna leads as shown.

93. Plug the vehicle antenna connector into the sub-feeder antenna 2-pin connector.

Without Navi

Without Navi AUDIO UNIT AUDIO UNIT

FM MODULATOR

i-VES HARNESS 20-PIN CONNECTOR

ANTENNA LEADS

VEHICLE ANTENNA CONNECTOR

DIN CABLE “B” TERMINAL

SUB-FEEDER ANTENNA 2-PIN CONNECTOR

EPT SEALER Cut in half.

4917120M

With Navi EPT SEALER Cut in half.

4917100M

20-PIN CONNECTOR LOCATION

With Navi

FM MODULATOR NAVIGATION UNIT

NAVIGATION UNIT

i-VES HARNESS 20-PIN CONNECTOR

ANTENNA LEADS

VEHICLE ANTENNA CONNECTOR

SUB-FEEDER ANTENNA 2-PIN CONNECTOR

DIN CABLE “B” TERMINAL 4917130M

EPT SEALER Cut in half. EPT SEALER Cut in half.

4917110M

94. Plug DIN cable “B” terminal into the FM modulator. 95. Plug the i-VES harness 20-pin connector into the audio unit/navigation unit. 96. Reinstall the audio unit/navigation unit.

© 2005 American Honda Motor Co., Inc - All Rights Reserved.

AII 28609 (0502)

25 of 26

97. Insert the Quick Reference Tag into the center console.

QUICK REFERENCE TAG

CENTER CONSOLE 4N11041H

98. Check that all wire harnesses are routed properly and all connectors are plugged in. 99. Reconnect the negative cable to the battery. 100. Enter the customer’s radio anti-theft code, and reset the radio station presets. 101.Reset the clock, and reset the radio station presets. 102. Check the operation of the in-Vehicle Entertainment System according to the Owner’s Manual provided. 103. Put the in-Vehicle Entertainment System Owner’s Manual in the glove box with the vehicle owner’s manual. 104. Reinstall all removed parts. Torque the seat belt anchor bolts to 30 to 35 N·m (21 to 25 lbf·ft) NOTE: Whenever the battery is disconnected, the driver’s AUTO function is disabled. 105.Start the engine. Push down on the driver’s window switch until the window is fully open. 106.Pull up on the driver’s window switch fully to close the window completely, then hold the switch for 2 seconds or more. 107.Test the window AUTO function.

26 of 26

AII 28609 (0502)

© 2005 American Honda Motor Co., Inc - All Rights Reserved.