INSTALLATION INSTRUCTIONS

OTHER TMI PRODUCTS STRIP DOORS INSTALLATION INSTRUCTIONS AIR DOORS BULK PVC FILM • STRIP • SHEET • PANEL SCREENS, CURTAINS and ENCLOSURES MEGA-P...
Author: Roland Riley
20 downloads 2 Views 2MB Size
OTHER TMI PRODUCTS

STRIP DOORS

INSTALLATION INSTRUCTIONS

AIR DOORS

BULK PVC FILM • STRIP • SHEET • PANEL

SCREENS, CURTAINS and ENCLOSURES

MEGA-PRO™ SWINGING DOORS IMPORTANT Carefully examine the carton(s) for damage. If the carton is damaged, immediately notify the shipping company.

DOCK ACCESSORIES

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING WITH INSTALLATION.

❏ Wall Mount ❏ Header Mount Overhead Bracket Mount – Projection –

❏ 12''

800•888•9750

Opens to:

❏ One Side ❏ Bi-Parting

❏ 18'' ❏ 24''

5350 Campbells Run Road • Pittsburgh, PA 15205-9738 • 412.787.9750 Fax: 412.787.3665 • Web Site: www.tmi-pvc.com • E-Mail: [email protected]

DOOR WIDTH Copyright © 2007 TMI, LLC

Catalog No. II-TMIASD 06-07

DOOR HEIGHT

PVC STRIP PLACEMENT

Your Accordion Strip Door has been custom built to your specifications. Those specifications should be clearly marked on the cover of these installation instructions.

After the assembled unit has been mounted using one of the 3 mounting methods, the PVC strips must be attached to the Accordion Assembly.

We highly recommend that the unit be mounted on the interior side of the doorway opening, basically to keep the mechanism out of the weather.

First, remove each Retaining Bar from the each Mounting Strip by unscrewing the nuts from the studs. NOTE: There are 2 nut / bolt combinations in the center of each strip.

MOUNTING METHODS There are 3 different mounting methods One Side that can be used: Wall Mount, Header Mount and Overhead Bracket Mount . . . . and each of these allows Overhead Wall Header Door Mount the door to Mount Mount be pulled to One Side or Bi-Parting Bi-Part.

Pages 2-5

With all the PVC Strips in place, your Save-T Accordion Strip Door is complete.

Pages 10 - 13

Pages 6-9

WARNING:

Then place the PVC Strips onto the studs. Replace the Retaining Strips and fasten with the nuts.

NOTES

Do not remove protective wrap from linkage assembly until it is installed into the sliding track. The assembly opens and closes in a scissorlike fashion. Serious injury may result from failure to follow directions.

WALL MOUNTING Opening to One Side and Bi-Parting With Multiple Sliding Tracks: Loosely place the supplied set screws into the splice connector. Place each sliding track into the ends of the connector and tighten the set screws. Now the combined track can be treated as a single sliding track. With a Single Sliding Track: First, place all of the wall hangers on the track. The two end hangers should be approximately 8'' in from either end of the track and the remaining hangers should be evenly spaced across the entire length of the track.

2

SET SCREWS

SLIDING TRACK WALL SPLICE CONNECTOR SLIDING TRACK

8''

8''

11

MOUNTING OVERHEAD DOOR COVER

3

Once the Overhead Door Bracket, Accordion Assembly and Side Strips are in place and secured, the PVC cover should be placed over the top of the entire unit to create a substantial ambient air barrier.

4

HANGER PLATE

LIP OF HEADER LIP OF HEADER

NOTE: The method of applying the cover, described here, is quite general since each overhead door and door rail configuration is different for each manufacturer.

INSIDE BRACE PLATE

DOOR RAIL

PVC COVER

Measure and cut both sides of the PVC cover accordingly, to accommodate the overhead door rail and inside brace plate on the Bracket. Use a utility knife.

Then, place the loosely assembled unit on the wall just above the header. The bottom edge of the hanger plate should line up with the edge or lip of the header.

5

CONCRETE or CONCRETE BLOCK

WOOD

VELCRO STRIPS PVC COVER

BACK BRACE TUBE

A Velcro ® strip should already be attached to the top of the Support Tube. However, the supplied pressure sensitive Velcro ® will have to be attached to the top of each Bracket and the Back Brace Tube, as well as the corresponding areas on the cover itself.

SUPPORT TUBE

Remove the unit and drill the marked holes with the proper size drill. This is determined by the material used in the construction of the header. If it’s wood, lag screws can be used. If it’s concrete or concrete blocks, anchored lag screws will be necessary. If the header is a steel plate, the hangers can be attached by welding.

For Bi-Parting Doors, skip to “ WALL MOUNTING - Bi-Parting”, page 5)

6

After the holes are drilled, attach the unit to the wall.

The next step is placing the Accordion Assembly into the sliding track. ANCHOR BAR

ANCHOR

VELCRO PLACEMENT BRACKETS and SUPPORT TUBES

PVC COVERS

VELCRO

10

Move each of the hangers slightly left or right, so the hanger will be attached to a firm portion of the wall. Mark all the hanger plate holes.

STEEL

MAGNETIC BRAKE ROLLER with PULL ROPE

VELCRO

MARK HOLES

PULL DOOR CLOSED TO THIS SIDE

First, you must determine which side of the mechanism will be anchored to the sliding track and to which side the strip door will be drawn. If there are no obstructions, either side can be used. However, if there is an obstruction close to the edge of the doorway opening, such as a wall or shelving, it would be best to anchor the mechanism to that side.

3

NOTE: The Magnetic Brake Roller & Pull Rope is attached to the second cross-member, opposite of the Anchor Bar. At this point, if you want to place the magnetic brake roller at a different cross-member, exchange the roller mechanisms now.

MAGNETIC BRAKE ROLLER with PULL ROPE

NOTE: The Magnetic Brake & Pull Rope Roller is attached to the second crossmember, opposite of the Anchor Bar. At this point, if you want to place the magnetic brake roller at a different cross-member, exchange the roller mechanisms now.

MAGNETIC BRAKE ROLLER with PULL ROPE

IMPORTANT: The closer the Pull Rope is to the center of the accordion assembly, the more difficult it will be to completely close the door. ANCHOR BAR

IMPORTANT: The closer the Pull Rope is to the center of the accordion assembly, the more difficult it will be to completely close the door.

For Closing to One Side using Single Accordion Assembly With the assembly compressed, slide each roller into the sliding track.

ANCHOR SIDE

MAGNETIC BRAKE ROLLER with PULL ROPE

NOTE: The anchor bar can be on either side . . . it’s your preference

MAGNETIC BRAKE ROLLER with PULL ROPE ANCHOR BAR

ANCHOR BOLT CAUTION: Do not remove the protective wrapping before placing assembly into sliding track.

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BOLT

ANCHOR BAR

SLIDING TRACK

SLIDING TRACK

With the unit compressed, slide each roller into the sliding track.

END STOP

Attach each anchor bar to the sliding track using the end stop, anchor bolt and 3 anchor nuts.

ANCHOR BAR

ANCHOR BAR

ANCHOR BAR

NUTS

NUTS

IMPORTANT: Be sure the anchor bar is facing the anchor side. Attach the anchor bar to the sliding track using the end stop, anchor bolt and 3 anchor nuts.

To complete the installation, attach the flexible PVC strips to the Accordion Assembly, see page 11.

For Bi-Parting Doors using Two Accordion Assemblies With both assemblies compressed, slide each roller into the sliding track. NOTE: The anchor bar for each assembly should be on the outside.

MAGNETIC BRAKE ROLLER with PULL ROPE

CAUTION: Do not remove the protective wrapping before placing assembly into sliding track. MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

ANCHOR BAR

4

END STOP

MAGNETIC BRAKE ROLLER with PULL ROPE

9

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

OVERHEAD DOOR MOUNTING

WALL MOUNTING

Bi-Parting Door

Opening to One Side and Bi-Parting NOTE: There are left and right brackets.

Your Overhead Door Bracket has been shipped with the Sliding Track Hangers already attached to the Support Tube.

ANCHOR

ANCHOR

SHELVING

SHELVING

or WALL

or WALL

PULL RIGHT TO CLOSE

First, bolt the Support Tube to the Mounting Brackets using the mounting bolts, washers and nuts. IMPORTANT: The hangers must be face down.

PULL LEFT TO CLOSE

MAGNETIC BRAKE ROLLER with PULL ROPE

BACK BRACE TUBE

With this method the strip door is attached to the wall just above the doorway opening. A Bi-Parting Door is generally used because there are obstructions on both sides of the doorway opening or there is a desire to keep one half of the doorway closed while traffic moves through the opening.

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

Next, attach the back Brace Tube to the Mounting Brackets. The method of attachment is your choice. One way is to drill holes and use nuts, bolt & washers; another is welding. We have given you this option because each door rail placement is different.

SLIDING TRACK

ANCHOR BAR

With Multiple Sliding Tracks or Single Sliding Track: To begin mounting, refer to steps 1 through 5 on pages 2 & 3. IMPORTANT: After the holes are drilled and before attaching the unit to the wall, both Accordion Assemblies should be placed into the sliding track.

PVC END STRIPS

Then, mount the End Strips of PVC to the brackets.

MAGNETIC BRAKE ROLLER with PULL ROPE

Next, place the assembled unit against the wall above the doorway opening. With the bottom of each PVC End Strip approximately 1/ 2” from the floor, level the unit and mark the mounting holes on the 2 Mounting Brackets.

Remove the unit and drill the marked holes with the proper size drill. This is determined by the material used in the construction of the wall. If it’s wood, lag screws can be used. If it’s concrete or concrete blocks, anchored lag screws will be necessary. If the header is a steel plate, the hangers can be attached by welding.

8

ANCHOR BAR

Place each unit so the Anchor Bar is MAGNETIC BRAKE ROLLER toward the end of the with PULL ROPE track and the Magnetic Brake & Pull Rope Roller is toward the center of the rail. Attach each anchor bar to the sliding track using the end stops, anchor bolts and anchor nuts. (See page 4 ) Once the Anchor Bars are fastened to either end of the track, the assembly now can be attached to the wall. CAUTION: Do not remove the protective wrapping before placing assembly into sliding track.

STEEL CONCRETE or CONCRETE BLOCK

WOOD

ANCHOR BAR

To complete the installation, attach the flexible PVC strips to the Accordion Assembly, see page 11.

5

HEADER MOUNTING

For Single Accordion Assembly – Closing to One Side:

Opening to One Side and Bi-Parting

With the assembly compressed, slide each roller into the sliding track. ANCHOR

With Multiple Sliding Tracks: Turn the splice connector so the backing plate faces down. Loosen (do not remove) the 4 LOOSEN CLAMP NUTS clamp nuts. Place each sliding track (open groove up) into the ends of the connector and tighten the nuts. Now the combined track can be treated as a OPEN GROOVE single sliding track.

NOTE: The anchor bar can be on either side . . . it’s your preference

CLAMP NUTS

MAGNETIC BRAKE ROLLER with PULL ROPE

OPEN GROOVE LOOSEN CLAMP NUTS MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BOLT

ANCHOR BAR

SLIDING TRACK

8''

With a Single Sliding Track: Loosen the 4 clamp nuts on all of the header hangers. Place 8'' all the hangers on the sliding track. The two end hangers should be approximately 8'' in from either end of the track. The remaining hangers should be evenly spaced across the entire length of the track. After positioning, tighten all the clamp nuts. Then place the assembled unit onto the header, between the door jambs. The hanger should be centered on the width of the header.

Attach each anchor bar to the sliding track using the end stop, anchor bolt and 3 anchor nuts.

ANCHOR BAR

ANCHOR BAR

NUTS

With both assemblies compressed, slide each roller into the sliding track.

MAGNETIC BRAKE ROLLER with PULL ROPE

CAUTION: Do not remove the protective wrapping before placing assembly into sliding track. MAGNETIC BRAKE ROLLER with PULL ROPE

BAR

Mark the mounting holes on each of the hangers.

MARK HOLES

ANCHOR BAR

WOOD

CAUTION: The accordion assembly must be in the sliding track, completely anchored, before it is welded into place. CONCRETE or CONCRETE BLOCK

MAGNETIC BRAKE ROLLER with PULL ROPE

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

Finally, attach the assembled unit to the header. To complete the installation, attach the flexible PVC strips to the Accordion Assembly, see page 11.

NOTE: Do not attach the unit to the header until the Accordion Assembly is in place. STEEL

6

END STOP

For Two Accordion Assemblies – Bi-Parting

NOTE: The anchor bar for each assembly should be on the outside. ANCHOR

Remove the unit and drill the marked holes with the proper size drill. This is determined by the material used in the construction of the header. If it’s wood, lag screws can be used. If it’s concrete or concrete blocks, anchored lag screws will be necessary. If the header is a steel plate, the hangers can be attached by welding.

ANCHOR SIDE

BAR

CLAMP NUTS

7

HEADER MOUNTING

For Single Accordion Assembly – Closing to One Side:

Opening to One Side and Bi-Parting

With the assembly compressed, slide each roller into the sliding track. ANCHOR

With Multiple Sliding Tracks: Turn the splice connector so the backing plate faces down. Loosen (do not remove) the 4 LOOSEN CLAMP NUTS clamp nuts. Place each sliding track (open groove up) into the ends of the connector and tighten the nuts. Now the combined track can be treated as a OPEN GROOVE single sliding track.

NOTE: The anchor bar can be on either side . . . it’s your preference

CLAMP NUTS

MAGNETIC BRAKE ROLLER with PULL ROPE

OPEN GROOVE LOOSEN CLAMP NUTS MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BOLT

ANCHOR BAR

SLIDING TRACK

8''

With a Single Sliding Track: Loosen the 4 clamp nuts on all of the header hangers. Place 8'' all the hangers on the sliding track. The two end hangers should be approximately 8'' in from either end of the track. The remaining hangers should be evenly spaced across the entire length of the track. After positioning, tighten all the clamp nuts. Then place the assembled unit onto the header, between the door jambs. The hanger should be centered on the width of the header.

Attach each anchor bar to the sliding track using the end stop, anchor bolt and 3 anchor nuts.

ANCHOR BAR

ANCHOR BAR

NUTS

With both assemblies compressed, slide each roller into the sliding track.

MAGNETIC BRAKE ROLLER with PULL ROPE

CAUTION: Do not remove the protective wrapping before placing assembly into sliding track. MAGNETIC BRAKE ROLLER with PULL ROPE

BAR

Mark the mounting holes on each of the hangers.

MARK HOLES

ANCHOR BAR

WOOD

CAUTION: The accordion assembly must be in the sliding track, completely anchored, before it is welded into place. CONCRETE or CONCRETE BLOCK

MAGNETIC BRAKE ROLLER with PULL ROPE

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

Finally, attach the assembled unit to the header. To complete the installation, attach the flexible PVC strips to the Accordion Assembly, see page 11.

NOTE: Do not attach the unit to the header until the Accordion Assembly is in place. STEEL

6

END STOP

For Two Accordion Assemblies – Bi-Parting

NOTE: The anchor bar for each assembly should be on the outside. ANCHOR

Remove the unit and drill the marked holes with the proper size drill. This is determined by the material used in the construction of the header. If it’s wood, lag screws can be used. If it’s concrete or concrete blocks, anchored lag screws will be necessary. If the header is a steel plate, the hangers can be attached by welding.

ANCHOR SIDE

BAR

CLAMP NUTS

7

OVERHEAD DOOR MOUNTING

WALL MOUNTING

Bi-Parting Door

Opening to One Side and Bi-Parting NOTE: There are left and right brackets.

Your Overhead Door Bracket has been shipped with the Sliding Track Hangers already attached to the Support Tube.

ANCHOR

ANCHOR

SHELVING

SHELVING

or WALL

or WALL

PULL RIGHT TO CLOSE

First, bolt the Support Tube to the Mounting Brackets using the mounting bolts, washers and nuts. IMPORTANT: The hangers must be face down.

PULL LEFT TO CLOSE

MAGNETIC BRAKE ROLLER with PULL ROPE

BACK BRACE TUBE

With this method the strip door is attached to the wall just above the doorway opening. A Bi-Parting Door is generally used because there are obstructions on both sides of the doorway opening or there is a desire to keep one half of the doorway closed while traffic moves through the opening.

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

Next, attach the back Brace Tube to the Mounting Brackets. The method of attachment is your choice. One way is to drill holes and use nuts, bolt & washers; another is welding. We have given you this option because each door rail placement is different.

SLIDING TRACK

ANCHOR BAR

With Multiple Sliding Tracks or Single Sliding Track: To begin mounting, refer to steps 1 through 5 on pages 2 & 3. IMPORTANT: After the holes are drilled and before attaching the unit to the wall, both Accordion Assemblies should be placed into the sliding track.

PVC END STRIPS

Then, mount the End Strips of PVC to the brackets.

MAGNETIC BRAKE ROLLER with PULL ROPE

Next, place the assembled unit against the wall above the doorway opening. With the bottom of each PVC End Strip approximately 1/ 2” from the floor, level the unit and mark the mounting holes on the 2 Mounting Brackets.

Remove the unit and drill the marked holes with the proper size drill. This is determined by the material used in the construction of the wall. If it’s wood, lag screws can be used. If it’s concrete or concrete blocks, anchored lag screws will be necessary. If the header is a steel plate, the hangers can be attached by welding.

8

ANCHOR BAR

Place each unit so the Anchor Bar is MAGNETIC BRAKE ROLLER toward the end of the with PULL ROPE track and the Magnetic Brake & Pull Rope Roller is toward the center of the rail. Attach each anchor bar to the sliding track using the end stops, anchor bolts and anchor nuts. (See page 4 ) Once the Anchor Bars are fastened to either end of the track, the assembly now can be attached to the wall. CAUTION: Do not remove the protective wrapping before placing assembly into sliding track.

STEEL CONCRETE or CONCRETE BLOCK

WOOD

ANCHOR BAR

To complete the installation, attach the flexible PVC strips to the Accordion Assembly, see page 11.

5

NOTE: The Magnetic Brake Roller & Pull Rope is attached to the second cross-member, opposite of the Anchor Bar. At this point, if you want to place the magnetic brake roller at a different cross-member, exchange the roller mechanisms now.

MAGNETIC BRAKE ROLLER with PULL ROPE

NOTE: The Magnetic Brake & Pull Rope Roller is attached to the second crossmember, opposite of the Anchor Bar. At this point, if you want to place the magnetic brake roller at a different cross-member, exchange the roller mechanisms now.

MAGNETIC BRAKE ROLLER with PULL ROPE

IMPORTANT: The closer the Pull Rope is to the center of the accordion assembly, the more difficult it will be to completely close the door. ANCHOR BAR

IMPORTANT: The closer the Pull Rope is to the center of the accordion assembly, the more difficult it will be to completely close the door.

For Closing to One Side using Single Accordion Assembly With the assembly compressed, slide each roller into the sliding track.

ANCHOR SIDE

MAGNETIC BRAKE ROLLER with PULL ROPE

NOTE: The anchor bar can be on either side . . . it’s your preference

MAGNETIC BRAKE ROLLER with PULL ROPE ANCHOR BAR

ANCHOR BOLT CAUTION: Do not remove the protective wrapping before placing assembly into sliding track.

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BOLT

ANCHOR BAR

SLIDING TRACK

SLIDING TRACK

With the unit compressed, slide each roller into the sliding track.

END STOP

Attach each anchor bar to the sliding track using the end stop, anchor bolt and 3 anchor nuts.

ANCHOR BAR

ANCHOR BAR

ANCHOR BAR

NUTS

NUTS

IMPORTANT: Be sure the anchor bar is facing the anchor side. Attach the anchor bar to the sliding track using the end stop, anchor bolt and 3 anchor nuts.

To complete the installation, attach the flexible PVC strips to the Accordion Assembly, see page 11.

For Bi-Parting Doors using Two Accordion Assemblies With both assemblies compressed, slide each roller into the sliding track. NOTE: The anchor bar for each assembly should be on the outside.

MAGNETIC BRAKE ROLLER with PULL ROPE

CAUTION: Do not remove the protective wrapping before placing assembly into sliding track. MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

ANCHOR BAR

4

END STOP

MAGNETIC BRAKE ROLLER with PULL ROPE

9

MAGNETIC BRAKE ROLLER with PULL ROPE

ANCHOR BAR

MOUNTING OVERHEAD DOOR COVER

3

Once the Overhead Door Bracket, Accordion Assembly and Side Strips are in place and secured, the PVC cover should be placed over the top of the entire unit to create a substantial ambient air barrier.

4

HANGER PLATE

LIP OF HEADER LIP OF HEADER

NOTE: The method of applying the cover, described here, is quite general since each overhead door and door rail configuration is different for each manufacturer.

INSIDE BRACE PLATE

DOOR RAIL

PVC COVER

Measure and cut both sides of the PVC cover accordingly, to accommodate the overhead door rail and inside brace plate on the Bracket. Use a utility knife.

Then, place the loosely assembled unit on the wall just above the header. The bottom edge of the hanger plate should line up with the edge or lip of the header.

5

CONCRETE or CONCRETE BLOCK

WOOD

HOOK & LOOP STRIPS PVC COVER

BACK BRACE TUBE

A hook and loop fastener strip should already be attached to the top of the Support Tube. However, the supplied pressure sensitive hook and loop will have to be attached to the top of each Bracket and the Back Brace Tube, as well as the corresponding areas on the cover itself.

SUPPORT TUBE

Remove the unit and drill the marked holes with the proper size drill. This is determined by the material used in the construction of the header. If it’s wood, lag screws can be used. If it’s concrete or concrete blocks, anchored lag screws will be necessary. If the header is a steel plate, the hangers can be attached by welding.

For Bi-Parting Doors, skip to “ WALL MOUNTING - Bi-Parting”, page 5)

6

After the holes are drilled, attach the unit to the wall.

The next step is placing the Accordion Assembly into the sliding track. ANCHOR BAR

MAGNETIC BRAKE ROLLER with PULL ROPE

HOOK AND LOOP PLACEMENT BRACKETS and SUPPORT TUBES

PVC COVERS

H&L

10

Move each of the hangers slightly left or right, so the hanger will be attached to a firm portion of the wall. Mark all the hanger plate holes.

STEEL

ANCHOR

H&L

MARK HOLES

PULL DOOR CLOSED TO THIS SIDE

First, you must determine which side of the mechanism will be anchored to the sliding track and to which side the strip door will be drawn. If there are no obstructions, either side can be used. However, if there is an obstruction close to the edge of the doorway opening, such as a wall or shelving, it would be best to anchor the mechanism to that side.

3

PVC STRIP PLACEMENT

Your Accordion Strip Door has been custom built to your specifications. Those specifications should be clearly marked on the cover of these installation instructions.

After the assembled unit has been mounted using one of the 3 mounting methods, the PVC strips must be attached to the Accordion Assembly.

We highly recommend that the unit be mounted on the interior side of the doorway opening, basically to keep the mechanism out of the weather.

First, remove each Retaining Bar from the each Mounting Strip by unscrewing the nuts from the studs. NOTE: There are 2 nut / bolt combinations in the center of each strip.

MOUNTING METHODS There are 3 different mounting methods One Side that can be used: Wall Mount, Header Mount and Overhead Bracket Mount . . . . and each of these allows Overhead Wall Header Door Mount the door to Mount Mount be pulled to One Side or Bi-Parting Bi-Part.

Pages 2-5

With all the PVC Strips in place, your Save-T Accordion Strip Door is complete.

Pages 10 - 13

Pages 6-9

WARNING:

Then place the PVC Strips onto the studs. Replace the Retaining Strips and fasten with the nuts.

NOTES

Do not remove protective wrap from linkage assembly until it is installed into the sliding track. The assembly opens and closes in a scissorlike fashion. Serious injury may result from failure to follow directions.

WALL MOUNTING Opening to One Side and Bi-Parting With Multiple Sliding Tracks: Loosely place the supplied set screws into the splice connector. Place each sliding track into the ends of the connector and tighten the set screws. Now the combined track can be treated as a single sliding track. With a Single Sliding Track: First, place all of the wall hangers on the track. The two end hangers should be approximately 8'' in from either end of the track and the remaining hangers should be evenly spaced across the entire length of the track.

2

SET SCREWS

SLIDING TRACK WALL SPLICE CONNECTOR SLIDING TRACK

8''

8''

11

OTHER TMI PRODUCTS

STRIP DOORS

INSTALLATION INSTRUCTIONS

AIR DOORS

BULK PVC FILM • STRIP • SHEET • PANEL

SCREENS, CURTAINS and ENCLOSURES

MEGA-PRO™ SWINGING DOORS IMPORTANT Carefully examine the carton(s) for damage. If the carton is damaged, immediately notify the shipping company.

DOCK ACCESSORIES

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING WITH INSTALLATION.

❏ Wall Mount ❏ Header Mount Overhead Bracket Mount – Projection –

❏ 12''

800•888•9750

Opens to:

❏ One Side ❏ Bi-Parting

❏ 18'' ❏ 24''

5350 Campbells Run Road • Pittsburgh, PA 15205-9738 • 412.787.9750 Fax: 412.787.3665 • Web Site: www.tmi-pvc.com • E-Mail: [email protected]

DOOR WIDTH Copyright © 2007 TMI, LLC

Catalog No. II-TMIASD 06-07

DOOR HEIGHT