INSTALLATION INSTRUCTIONS PARTS LIST
Accessory
Application
ACCESSORY HANDSFREELINK
2009 RIDGELINE
Publications No.
AII 40323 Issue Date
AUG 2008
Fuse label
HFL Attachment Kit P/N 08E02-SJC-100A HFL trim 2A Fuse
HFL bracket
HFL harness
HFL subharness
2
5
EPT sealers
10 Wire ties
4
Self-tapping screws, 3 x 10 mm
2
Washer screws, 4 x 10 mm
Double-sided tapes Ground bolt
HFL retainer
Bushing
Template
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
Screw
AII 40323 (0808)
08E02-SJC-1A00-91
1 of 13
Rubber bumper
Illustration of the HFL System Installed on the Vehicle HFL HARNESS
HFL Kit P/N 08E00-E10-100
HFL SUBHARNESS
Switch
CONTROL UNIT
SWITCH
Control unit
811420AE
User’s information Manual
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
Flat-tip screwdriver Shop towel
1.
Make sure you have the anti-theft code for the audio unit and the navigation system, then write down the radio presets.
2.
Disconnect the negative cable from the battery.
Isopropyl alcohol Diagonal cutters Ratchet 10 mm Socket 10 mm Combination wrench Utility Knife T-25 Torx wrench Felt-tip pen Masking tape Pushpin Drill 3 mm, 4.5 mm, 6 mm, 9 mm, and 10 mm Drill bits 20 mm Hole saw Plastic trim tool T/N SILTRIMTL 10 Scissors Eye protection (face shield, safety goggle, etc.)
2 of 13
AII 40323 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
Removing the vehicle parts 3.
4.
Open the sunglass holder.
Disengage eight retaining tabs, and remove the left and right lenses from the roof console. VEHICLE CONNECTORS
With moonroof:
ROOF CONSOLE ROOF CONSOLE
SUNGLASS HOLDER Open.
RIGHT LENS 4 RETAINING TABS
LEFT LENS
PLASTIC TRIM TOOL
2 SCREWS (Silver)
2 SCREWS (Black)
4 RETAINING TABS
811422AE
5.
Remove two screws (Black), two screws (Silver) and let the roof console drop down. Unplug the vehicle connectors and remove the roof console.
6.
Turn the left sunvisor toward the driver’s seat.
811809AE
Without moonroof:
SUNVISOR HOLDER
PLASTIC TRIM TOOL
ROOF CONSOLE
VEHICLE CONNECTOR SUNVISOR SCREW COVER
RIGHT LENS 4 RETAINING TABS
LEFT LENS
4 RETAINING TABS
LEFT SUNVISOR
4 RETAINING TABS PLASTIC TRIM TOOL
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
2 T-25 TORX SCREWS
811101AE
831708AX
7.
Remove the sunvisor screw cover (four retaining tabs).
8.
Locate the slot in the sunvisor holder and insert a plastic trim tool into the slot. Push in and release the retaining tab.
9.
Remove the left sunvisor (two T-25 torx screws, and unplug the vehicle connector).
AII 40323 (0808)
3 of 13
10. Peel the weatherstrip.
13. Remove the left dashboard side cover (seven clips).
PLASTIC TRIM TOOL
7 CLIPS CLIP
SIDE CURTAIN AIR BAG CLIP
LEFT DASHBOARD SIDE COVER WEATHERSTRIP Peel.
LEFT A-PILLAR TRIM
811102BE
11. Release the side curtain air bag clip and remove the left A-pillar trim (one clip).
831901AB
14. Remove the driver’s dashboard lower cover (one self-tapping screw, nine clips, one vehicle connector).
12. Pull out the fuel fill door release handle. Remove the left front door sill trim (three clips and three retaining tabs). 2 RETAINING TABS
VEHICLE CONNECTOR
2 CLIPS
FUEL FILL DOOR RELEASE HANDLE CLIP
SELF-TAPPING SCREW
RETAINING TAB
FRONT LEFT FRONT DOOR SILL TRIM
4 of 13
9 CLIPS
DRIVER’S DASHBOARD LOWER COVER
7D2003BX
7D2007AX
AII 40323 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
15. Peel the weatherstrip from the left kick panel. Remove the left kick panel (one screw clip and one clip).
17. Attach one fuse label (2A) to the HFL subharness fuse case.
WEATHERSTRIP SCREW CLIP FUSE LABEL (2A)
CLIP
HFL SUBHARNESS FUSE CASE
HFL SUBHARNESS
LEFT KICK PANEL
811104AE
7D2008AX
18. Plug the HFL subharness 6-pin connector to the 6-pin opening on the fuse box.
Installing the control unit and routing the harness 16. Attach three EPT sealers to the 4-pin connector side of the HFL subharness at the positions shown. EPT SEALER
HFL SUBHARNESS
EPT SEALER 50 mm 100 mm 50 mm
HFL SUBHARNESS 4-PIN CONNECTOR
EPT SEALER HFL SUBHARNESS
FUSE BOX 811103CE
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
AII 40323 (0808)
6-PIN OPENING
HFL SUBHARNESS 6-PIN CONNECTOR 811105BE
5 of 13
19. If other accessory is already plugged into the 6-pin connector, remove the dummy connector from the 6pin connector taped to the HFL subharness. Plug the other accessory 6-pin connector into the HFL subharness and plug the HFL subharness into the fuse box.
21. Secure the HFL subharness to the vehicle harness with one wire tie.
FUSE BOX HFL SUBHARNESS 6-PIN CONNECTOR
WIRE TIE DUMMY CONNECTOR
HFL SUBHARNESS VEHICLE HARNESS
811108BE
22. Route the HFL subharness as shown, and secure it to the vehicle harness with one wire tie.
OTHER ACCESSORY 6-PIN CONNECTOR 811106AE
HFL SUBHARNESS 1-PIN CONNECTOR
20. Remove the vehicle bolt and install the ground bolt with HFL subharness ground terminal as shown. FUSE BOX
HFL SUBHARNESS
WIRE TIE VEHICLE HARNESS
GROUND BOLT
VEHICLE BOLT Discard. HOOD OPENER
HFL SUBHARNESS GROUND TERMINAL
VEHICLE HARNESS 1-PIN CONNECTOR
811107BE
842402AD
23. Unplug the vehicle harness 1-pin connector and plug it to the HFL subharness 1-pin connector. 24. Plug the HFL subharness 1-pin connector to the vehicle 1-pin connector.
6 of 13
AII 40323 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
25. Cut one EPT sealer in half and attach one half to the HFL subharness connection part.
28. Route the HFL subharness along the vehicle harness as shown.
EPT SEALER
HFL SUBHARNESS CONNECTION PART EPT SEALER Cut in half.
WIRE TIE
4 WIRE TIES
HFL SUBHARNESS CONNECTION PART
HFL SUBHARNESS
VEHICLE HARNESS
VEHICLE HARNESS
LEFT A-PILLAR TRIM OPENING
811111AE
29. Secure the HFL subharness to the vehicle harness with four wire ties. 30. Using scissors, cut out template A and template B. VEHICLE HARNESS 1-PIN CONNECTOR 811109CE
TEMPLATE A
26. Secure the HFL subharness connection part to the vehicle harness with one wire tie. 27. Route the HFL subharness to the A-pillar trim opening, and secure it to the vehicle harness with two wire ties as shown.
TEMPLATE
VEHICLE HARNESS
TEMPLATE B HFL SUBHARNESS 2 WIRE TIES
811401AE
811110CE
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
AII 40323 (0808)
7 of 13
31. Remove the damper (two screws).
35. Attach masking tape onto the roof console as shown.
SUNGLASS HOLDER
ROOF CONSOLE
VEHICLE BUSHING
PIN ROOF CONSOLE 9 mm DRILL BIT
SCREW CAMSET LOCK 2 RETAINING TABS
MASKING TAPE
DAMPER 2 SCREWS
811402AE
32. Remove the sunglass holder from the roof console (one screw and one vehicle bushing). 33. Remove the pin and remove the camset lock (two retaining tabs).
DRILL 811404BE
36. While wearing eye protection, enlarge the hole on the roof console with a 9 mm drill bit. 37. Remove the masking tape. 38. Attach masking tape to the roof console as shown.
34. Remove the console light from the roof console (four retaining tabs).
MASKING TAPE
ROOF CONSOLE
ROOF CONSOLE
4 RETAINING TABS 811405AE
CONSOLE LIGHT
8 of 13
811403AE
AII 40323 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
39. Attach template A to the roof console at the indicated position with masking tape.
ROOF CONSOLE
43. Attach template B with masking tape to the roof console at the position shown. PUSHPIN
CENTER OF THE ROOF CONSOLE
FELT-TIP PEN
PUSHPIN FELT-TIP PEN 4 MARKS
TEMPLATE B
MARK
MASKING TAPE 2 MARKS
PUSHPIN
MASKING TAPE ROOF CONSOLE
TEMPLATE A
CENTER OF THE ROOF CONSOLE
811408AE
811406AE
40. Using a felt-tip pen, mark the center of the roof console as shown.
44. Using a pushpin, mark the roof console at four locations according to template B.
41. Using a pushpin, mark the roof console at two locations according to template A. Remove template A.
45. Using a felt-tip pen, mark the roof console along template B. Remove template B.
42. While wearing eye protection, drill two 4.5 mm holes at the locations marked on the roof console in step 41. Remove any burrs. 4.5 mm DRILL BIT
ROOF CONSOLE
DRILL
2 MARKS 811407AE
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
AII 40323 (0808)
9 of 13
46. While wearing eye protection, drill four 3 mm holes at the locations marked on the roof console in step 44.
49. Using an utility knife, cut along the mark made on the roof console in step 45. Remove any burrs. UTILITY KNIFE
ROOF CONSOLE
DRILL 20 mm HOLE SAW
Mark made in step 45. 3 mm DRILL BIT
ROOF CONSOLE 4 MARKS 3 mm 6 mm 10 mm DRILL BIT
Cut out. ROOF CONSOLE
Cut out. 811410AE
DRILL
50. Remove the masking tape attached in step 38.
ROOF CONSOLE
DRILL
811409AE
51. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the two double-sided tapes will attach. Remove the adhesive backing from the double-sided tapes and attach the double-sided tapes at the indicated position on the control unit as shown.
47. Enlarge the lower two 3 mm holes drilled in step 46 with a 6 mm drill bit and then with a 10 mm drill bit as shown.
ADHESIVE BACKING
48. Enlarge the upper two 3 mm holes drilled in step 46 with a 20 mm hole saw as shown.
2 DOUBLE-SIDED TAPES ADHESIVE BACKING
CONTROL UNIT
10 mm
10 mm
CONTROL UNIT
10 of 13
AII 40323 (0808)
811411BE
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
52. Plug the HFL harness 22-pin connector to the control unit. CONTROL UNIT
CONTROL UNIT
Installing the switch 55. Insert the rubber bumper to the HFL retainer.
CENTER
ROOF CONSOLE
HFL TRIM
Do not cover these installation holes. SWITCH HFL HARNESS
Remove the adhesive backing.
HFL HARNESS 22-PIN CONNECTOR
HFL RETAINER 811412AE
ROOF CONSOLE
53. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the double-sided tapes will attach. Remove the adhesive backing from the two double-sided tapes attached to the control unit and attach the control unit to the roof console at the indicated position. Do not cover the installation holes with the control unit.
4 SELF-TAPPING SCREWS, 3 x 10 mm
54. Use the holes drilled in step 42 and secure the HFL bracket to the roof console with two 4 x 10 mm washer screws.
HFL RETAINER
Holes drilled in step 42. RUBBER BUMPER
771012BB
56. Assemble the HFL retainer, switch, and HFL trim with four 3 x 10 mm self-tapping screws.
2 WASHER SCREWS, 4 x 10 mm
ROOF CONSOLE HFL BRACKET
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
811413AE
AII 40323 (0808)
11 of 13
57. Plug the HFL harness 20-pin connector to the switch.
SCREW Reused
61. Hold the roof console close to the roof console opening and plug the HFL harness 4-pin connector to the HFL subharness 4-pin connector. HFL SUBHARNESS 4-PIN CONNECTOR
SWITCH
ROOF CONSOLE OPENING
ROOF CONSOLE
EPT SEALER Other half from step 60. CONSOLE LIGHT
VEHICLE BUSHING Reused
HFL HARNESS 4-PIN CONNECTOR
BUSHING
HFL HARNESS 20-PIN CONNECTOR
HFL HARNESS
811414AE
ROOF CONSOLE
SCREW
811416BE
58. Install the switch assembled in step 56 to the roof console with the screw and vehicle bushing removed in step 32, and the screw and bushing from the kit. 59. Reinstall the console light to the roof console.
62. Wrap one half EPT sealer cut in step 60 to the HFL subharness 4-pin connector. 63. Secure the HFL harness to the vehicle harness with one wire tie.
60. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the EPT sealer will attach. Cut one EPT sealer in half and attach one half to the vehicle bracket as shown.
WIRE TIE
HFL HARNESS
ROOF CONSOLE OPENING
VEHICLE BRACKET
VEHICLE HARNESS ROOF CONSOLE 831709AX
EPT SEALER Cut in half.
12 of 13
EPT SEALER
811415BE
AII 40323 (0808)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
64. Plug the vehicle connectors to the roof console. Reinstall the roof console with four screws removed in step 5.
66. Install the 2A fuse into the No.33 slot of the fuse box.
FUSE BOX VEHICLE CONNECTORS
ROOF CONSOLE
2A FUSE
No.33 SLOT
811418AE
2 SCREWS (Black)
2 SCREWS (Silver)
811417BE
67. Attach the fuse label (OPTION FUSE 2A) to the No.33 on the inside of the fuse box cover.
Installing the Fuse FUSE LABEL (OPTION FUSE 2A)
65. Remove the fuse box cover from the fuse box. FUSE BOX COVER FUSE BOX FUSE BOX COVER
No.33
811419AE
811421AE
68. Check that all wire harness are routed properly and all connectors are plugged in. 69. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. 70. Reconnect the negative cable to the battery. 71. Enter the customer’s radio anti-theft code, and reset the audio station presets. 72. Reset the clock.
© 2008 American Honda Motor Co., Inc. – All Rights Reserved.
AII 40323 (0808)
13 of 13