Accessory
INSTALLATION INSTRUCTIONS
Application
Publications No.
AII 40271 ACCESSORY HANDSFREELINK
PARTS LIST
2009 ODYSSEY
Issue Date
AUG 2008
Fuse label
HFL Attachment Kit P/N 08E02-SHJ-100B HFL trim Fuse (2 A)
HFL bracket
6 EPT sealers
HFL harness
8 Wire ties
HFL subharness
4 Self-tapping screw, 3 x 10 mm
2 Washer screws, 4 x 12 mm
2 Double-faced tapes Self-tapping screw HFL retainer Bushing
Ground bolt Template
Rubber bumper
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 40271 (0808)
08E02-SHJ-1B00-91
1 of 12
Bluetooth HFL Kit P/N 08E00-E10-100
Illustration of the HFL Installed on the Vehicle
Switch
SWITCH
CONTROL UNIT HFL HARNESS
Control unit FUSE (2 A)
Accessory User's Information Manual HFL SUBHARNESS 7518071E
INSTALLATION TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver 10 mm Combination wrench 10 mm and 14 mm Socket Pushpin Ratchet 3 mm, 4.5 mm, 6 mm, 9 mm, and 10 mm Drill bit Eye protection (face shield, safety goggles, etc.) File
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.
Make sure you have the anti-theft code for the audio unit, then write down the frequencies for the preset buttons.
2.
Disconnect the negative cable from the battery.
Diagonal cutters Scissors Masking tape Tape measure Cardboard Isopropyl alcohol Shop towel 19 mm Holesaw Drill Utility knife T15 Torx bit Felt-tip pen Plastic trim tool (SILTRIMTL10)
2 of 12
AII 40271 (0808)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
3.
Disengage eight retaining tabs and remove the left and right lens from the roof console.
7.
Using a flat-tip screwdriver, push the hook and turn the holder. Remove the holder. PLASTIC TRIM TOOL
VEHICLE CONNECTORS
SUNVISOR HOLDER
VEHICLE CONNECTOR
ROOF CONSOLE
SUNGLASS HOLDER (Open.)
COVER
RIGHT LENS
LEFT SUNVISOR
RETAINING TAB
2 SCREWS
4 RETAINING TABS
2 BOLTS 4 RETAINING TABS
8.
Disengage two screws and remove the left sunvisor.
9.
Pull away the weatherstrip from the left A-pillar trim. Release the side curtain air bag clip by using the plastic trim tool and remove the left A-pillar (two clips).
2 BOLTS
LEFT LENS
7517010E
4.
Open the sunglass holder.
5.
Remove four bolts and lower the roof console.
6.
Disconnect the two vehicle connectors and remove the roof console.
PLASTIC TRIM TOOL
WEATHERSTRIP SIDE CURTAIN AIR BAG CLIP LEFT A-PILLAR TRIM
CLIP
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 40271 (0808)
3 of 12
10. Remove the left front door sill trim (three clips).
LEFT FRONT DOOR SILL TRIM
12. Attach the fuse label (2 A) to the fuse case of the HFL subharness.
3 CLIPS FUSE LABEL (2 A)
HFL SUBHARNESS FUSE CASE
HFL SUBHARNESS
7821100B
4301210B
11. Pull away the weatherstrip from the left kick panel. Remove the left kick panel (three clips).
WEATHERSTRIP
13. Plug the HFL subharness 6-pin connector into the 6-pin opening in the fuse box.
3 CLIPS
HFL SUBHARNESS
LEFT KICK PANEL 6-PIN CONNECTOR
4301221B
FUSE BOX
4 of 12
AII 40271 (0808)
7517042E
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the 6-pin connector taped to the HFL subharness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the HFL subharness you just unplugged and plug the HFL subharness into the fuse box.
16. Remove the vehicle bolt (discard) and install the ground bolt with HFL subharness ground terminal as shown.
FUSE BOX HFL SUBHARNESS 6-PIN CONNECTOR
GROUND BOLT FUSE BOX VEHICLE BOLT (Discard.)
FUEL OPENER
HFL SUBHARNESS GROUND TERMINAL DUMMY CONNECTOR
HOOD OPENER
7517051E
17. Disconnect the vehicle harness 1-pin connector and connect it to the HFL subharness 1-pin connector.
OTHER ACCESSORY 6-PIN CONNECTOR 4319060B
VEHICLE HARNESS 1-PIN CONNECTOR
14. Route the HFL subharness to the left A-pillar trim opening.
HFL SUBHARNESS 1-PIN CONNECTOR
HFL SUBHARNESS HFL SUBHARNESS WIRE TIE GREEN TAPE
VEHICLE HARNESS
VEHICLE CLIP
EPT SEALER
VEHICLE HARNESS
EPT SEALER Cut in half. LEFT A-PILLAR TRIM OPENING
7517072E 7517031E
15. Route the HFL subharness and secure the harness to the vehicle harness with a wire tie above the vehicle clip as shown.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
HFL SUBHARNESS CONNECTION PART HFL SUBHARNESS
18. Connect the HFL subharness 1-pin connector to the vehicle 1-pin connector. 19. Wrap the cut one half of the EPT sealer on the HFL subharness connection part.
AII 40271 (0808)
5 of 12
20. Secure the HFL subharness to the vehicle harness with a wire tie.
23. Cut the template into template A and template B.
VEHICLE PANEL EPT SEALER
TEMPLATE A TEMPLATE
WIRE TIE HFL SUBHARNESS
TEMPLATE B
7517091E
24. Remove the damper (two tapping screws). VEHICLE HARNESS
7517061E
SUNGLASSES HOLDER
21. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Attach a EPT sealer to secure the HFL subharness to the vehicle panel.
ROOF CONSOLE
22. Secure the HFL subharness to the vehicle harness with three wire tie.
VEHICLE BUSHING PIN
TAPPING SCREW
HFL SUBHARNESS 3 WIRE TIES
2 RETAINING TABS 2 TAPPING SCREWS
VEHICLE HARNESS
CAMSET LOCK
DAMPER 7517101E
25. Remove the sunglasses holder (tapping screw and vehicle bushing). 26. Remove the pin and remove the camset lock (two retaining tabs). 7517080E
6 of 12
AII 40271 (0808)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
27. Remove the console light from the roof console (four retaining tabs).
29. Attach masking tape to the roof console as shown.
ROOF CONSOLE
MASKING TAPE
ROOF CONSOLE
4 RETAINING TABS
7716020X
CONSOLE LIGHT
7523030E
30. Attach template A with masking tape to the roof console at the indicated position. ROOF CONSOLE CENTER OF THE ROOF CONSOLE
PUSHPIN
28. Enlarge the hole on the roof console with a 9 mm drill bit.
FELT-TIP PEN ROOF CONSOLE
MARK MASKING TAPE 2 MARKS
TEMPLATE A
7517112E
31. Using a felt-tip pen, mark the center of the roof console as shown.
DRILL BIT (9 mm)
32. Use a pushpin to mark the roof console at two locations according to template A. 7524060E
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
33. Remove template A.
AII 40271 (0808)
7 of 12
34. Drill 4.5 mm holes at the two locations marked on the roof console in step 32. After drilling, remove any burrs.
39. Drill a 3 mm hole at the four locations marked on the roof console in step 36. 19 mm HOLESAW
DRILL BIT (4.5 mm)
DRILL BIT (3 mm)
ROOF CONSOLE
ROOF CONSOLE 4 MARKS
DRILL BIT (3 mm 6 mm 10 mm)
2 MARKS
7517120E
DRILL
35. Attach template B with masking tape on the roof console at the indicated position. 7517141E
PUSHPIN
40. Enlarge the two 3 mm holes drilled in step 39 with a 6 mm drill bit and with a 10 mm drill bit as shown.
FELT-TIP PEN
4 MARKS
TEMPLATE B
MASKING TAPE ROOF CONSOLE
41. Enlarge the other two 3 mm holes drilled in step 39 with a 19 mm holesaw as shown.
PUSHPIN
CENTER OF THE ROOF CONSOLE 7517131E
36. Use a pushpin to mark the roof console at four locations according to template B. 37. Use a felt-tip pen and mark the roof console along template B. 38. Remove template B.
8 of 12
AII 40271 (0808)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
42. Using a utility knife, cut along the marking made on the roof console in step 37. After cutting, remove any burrs. ROOF CONSOLE
45. Connect the HFL harness 22-pin connector to the control unit. CENTER CONTROL UNIT
UTILITY KNIFE
Mark made in step 37. CONTROL UNIT
Cut out.
HFL HARNESS
ROOF CONSOLE
Remove the adhesive backing.
ROOF CONSOLE
HFL HARNESS 22-PIN CONNECTOR ROOF CONSOLE
Cut out.
7517171E
7517152E
43. Remove the masking tape attached in step 29. 44. Using isopropyl alcohol on a shop towel, clean the areas where the double-faced tape will attach. Remove the adhesive backing from double-faced tape and attach the double-faced tape at the indicated position on the control unit. 2 DOUBLE-FACED TAPES
46. Using isopropyl alcohol on a shop towel, clean the areas where the double-faced tape will attach. Remove the adhesive backing from the doublefaced tape attached to the control unit and attach to the roof console at the indicated position. 47. Use the holes drilled in step 34 and secure the HFL bracket with two 4 x 12 mm washer screws to the roof console. Holes drilled in step 34.
CONTROL UNIT
10 mm
10 mm
2 WASHER SCREWS, 4 x 12 mm CONTROL UNIT
ROOF CONSOLE HFL BRACKET
7517180E
7517161E
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 40271 (0808)
9 of 12
51. Connect the HFL harness 20-pin connector to the switch.
48. Bend the switch terminal as shown. BACKSIDE OF THE SWITCH
SWITCH TERMINAL (Bend.)
SELF- TAPPING SCREW (Reused)
SPEAKER SWITCH
SWITCH TERMINAL HFL TRIM
VEHICLE BUSHING (Reused) SWITCH BUSHING
HFL RETAINER
HFL HARNESS 20 -PIN CONNECTOR
ROOF CONSOLE
SELF- TAPPING SCREW
7517192E
52. Install the switch assembled in step 50 to the roof console with self-tapping screw and bushing removed in step 25, and a self-tapping screw and bushing from the kit. 53. Reinstall the console light to the roof console. 54. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Cut an EPT sealer in half and attach one half to the vehicle bracket as shown.
4 SELF-TAPPING SCREWS, 3 x 10 mm RUBBER BUMPER HFL RETAINER
ROOF CONSOLE 791209AB
49. Insert the rubber bumper to the HFL retainer. 50. Assemble HFL retainer, switch, and HFL trim with four 3 x 10 mm self-tapping screws. VEHICLE
EPT SEALER (Cut in half.)
10 of 12
AII 40271 (0808)
7518010E
EPT SEALER
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
55. Hold the roof console close to the roof console opening and connect the HFL harness 4-pin connector to the HFL subharness 4-pin connector.
GREEN CONNECTOR
58. Connect the vehicle connectors to the roof console. Reinstall the roof console with the four bolts from step 5.
VEHICLE CONNECTORS
WIRE TIE
VEHICLE BRACKET HFL SUBHARNESS 4-PIN CONNECTOR
Vehicle front
ROOF CONSOLE
ROOF CONSOLE OPENING
7518042E
HFL HARNESS 4-PIN CONNECTOR
2 BOLTS 2 BOLTS
ROOF CONSOLE
59. Install the fuse (2 A) into the fuse box at the indicated position.
7518020E
56. Secure the connector with a wire tie to the vehicle bracket. 57. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Secure the HFL subharness to the vehicle roof panel inside the roof lining with three EPT sealers. 3 EPT SEALERS
ROOF PANEL
HFL SUBHARNESS FUSE BOX
FUSE (2 A) 2219080T
7518030E
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
AII 40271 (0808)
11 of 12
60. Attach the fuse label to the No. 33 slot on the fuse box cover.
61. Check that all wire harnesses are routed properly and that all connectors are plugged in. 62. Reinstall all removed parts.
FUSE LABEL (OPITION FUSE 2 A)
63. Reconnect the negative cable to the battery. 64. Enter the customer’s audio unit anti-theft code, and reset the radio station presets.
FUSE BOX COVER
65. Reset the clock. 64. Initialize and test the front window auto/down function.
No. 33
2219090T
12 of 12
AII 40271 (0808)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.