®
A R C H I T E CT U R A L
A R E A
L I G H T I N G
ENERGY EFFICIENCY
LONGEVITY
SUSTAINABILITY
AAL’s Providence is designed to use electrical energy in the most efficient possible way. The reflectors are designed to precisely direct the illumination on the ground with no stray light which translates into wasted energy. The result is more light with less energy consumption.
AAL manufactures all its products to have a life span as long as the buildings or spaces they illuminate. The primary material used for all our products is aluminum to resist corrosion and the need for maintenance. Aluminum will not need the periodic refinishing required of steel products that will eventually rust and corrode. All our internal parts and fasteners are made of aluminum or stainless steel. The lamp enclosures are kept dust free and dry to prevent light degradation and maintain a high level of energy efficiency.
Our products are developed with recycling and resource management in mind. We recycle all incoming packaging materials. Our products are shipped in easy to recycle packaging materials. Our state of the art finishing system uses eco-friendly cleansing and preparation chemicals that are harmless enough to send to the drain without further processing. Our powder coating process eliminates the release of volatile chemicals into the atmosphere. AAL makes the Providence, like all AAL products, with renewable materials such as aluminum and stainless steel.
LIGHT POLLUTION Providence reflectors are designated as cutoff for indirect or full cutoff for horizontal reflectors. Full cutoff means there is no light emitted above 90 degrees horizontal.
TABLE OF
Contents
Design Excellence........................... 8 Elevated Scales ............................. 10 Optical Systems ............................ 12 Revolutionary Technology ............. 14
Modern Lighting Performance
Aesthetics in Traditional Forms
with
® Providence® MicroCore LED – Advanced LED Technology for Outdoor Lighting
LifeShield ....................................... 16 Upgrade Kits ................................. 17 Providence Large (PROL) ............. 18 Providence Medium (PROV) ......... 22 IDA Approved Dark-Sky Friendly versions of these luminaires are available.
Providence Small (PROS).............. 26 Providence Bollard (PROB) ........... 30 Providence Sconce (PRSC) .......... 34 TM
Providence is registered and protected by a patent granted by the United States Patent Office. U.S. Patent D515,231
2
Providence is a registered trademark of Architectural Area Lighting. ©2011 Architectural Area Lighting
PROVIDENCE
®
FAMILY
3
The
®
family
are transitional style fixtures that combine modern lighting performance with aesthetics in traditional forms. The Providence Bollard utilizes efficient lamp sources, including LED. Die-cast aluminum construction is corrosion resistant. Available with horizontal
Providence Sconce
full cutoff optic system, and tamper resistant hardware. Other models include wall sconce, small, medium and large luminaires.
AAL CodeLink
SM
PRSC spec sheet
Providence Bollard
AAL CodeLink
SM
Providence Medium
Providence Small AAL CodeLink
SM
AAL CodeLink
SM
AAL CodeLink
SM
Providence Large
PROB spec sheet
4
PROS spec sheet
PROV spec sheet
PROL spec sheet
PROVIDENCE
®
FAMILY
5
PROV-WMA56
Elegant
traditional form ®
LED
PROV-CP3
Part of AAL’s
Designer SSL Series
6
PROVIDENCE
®
FAMILY
7
DESIGN EXCELLENCE LARGE/MEDIUM LED
SCONCE
Providence Sconce is available with four precise optical systems, including pencil beam/column light, allowing you to precisely illuminate architectural features. Available as an uplight, downlight or an uplight/ downlight combination, with an optional R111 as the secondary opposing output source.
Featuring MicroEmitter™ Technology Bi-directional capabilities available with R111 as secondary opposing output source (2R). Also available with pencil up beam with optional color filter (2DPB)
Glare guard perimeter reflector redirects stray Heat sink aluminum carrier plate helps dissipate heat and prolongs LED life Hammertone center reflector evenly distributes light directly beneath the
The Providence Sconce also features highly efficient LED’s providing a Type 5 distribution. Features 4 modules with 9 LED’s per module for a total of 36 LED’s (37 watts), and available in Warm White (3500K) or Bright White (5100K) color temperatures. Other efficient sources offered include CFL, induction systems and the new 60 watt Philips Cosmopolis™* lamp.
Precisely aimed MicroEmitters put light where it is needed and significantly reduce glare Individual MicroEmitters are field replaceable
* Cosmopolis™ is a registered trademark of Philips Lighting.
EmitterDeck™ assembly is upgradeable as LED technology advances, or convert existing Providence HID into LEDs
Die-cast housing for maximum durability One-piece memory retentive gasket Providence LED, part of AAL's Designer SSL Series, is the first truly elegant LED luminaire on the market today. Its distinctive styling and high performance sets it apart from all others. One look is all it takes to discern that Providence is the epitome of quality and beauty.
Tool-less access Decorative struts conceal wiring
Decorative spikes available
BOLLARD RD-Smooth body
SMALL LED
FL-Fluted body
LED module
MEDIUM Horizontal Reflector
The Providence Bollard features a symmetrical horizontal optical system, and employs the most efficient light sources on the market today. This includes highly efficient LED’s providing Type1, Type 3 or Type 5 distribution, as well as compact fluorescent and the new Mini MasterColor® lamps.
INDIRECT OPTICAL SYSTEM Specify either the PROS or PROV with AAL’s revolutionary indirect optical system for extremely even illumination and improved comfort. The indirect system eliminates uplight for dark sky compliance without an overly bright hot spot of light directly below the fixture. The primary optical system is designed to tightly control upward illumination. This highly engineered optical system results in less than 1% uplight, earning an IES “cutoff” classification.
The lower optical system consists of a lamp and highly polished reflector. The reflector is specifically designed to focus the beam of an ED-17 or T6 metal halide lamp.
EVEN, GLARE-FREE ILLUMINATION The upper reflector directs the primary beam into a symmetric or asymmetric beam of light on the ground.
AAL is proud to be an official Energy Star Partner and DOE Official SSL Quality Advocate.
Upper reflector symmetric distribution (Indirect)
Upper reflector asymmetric distribution (Indirect)
LED Exclusive MicroEmitter Technology
™
As part of AAL’s Designer SSL Series, Providence Large and Medium scale luminaire features AAL's exclusive MicroEmitter™ technology which tightly and precisely controls powerful LED output while minimizing glare.
PROVIDENCE
®
FAMILY
11
REVOLUTIONARY TECHNOLOGY
COMFORTABLE, UNIFORM ILLUMINATION
Entire EmitterDeck is Upgradeable as LED Technology Advances
1 Canted MicroEmitter design precisely aims each diode at 70°, 60°, or 50° angles for maximum reach and uniform illumination EmitterDeck™ Assembly
°
60
er
itt
Em
o
icr
Mi
cro
M
t sa
le
rs
itte
Em
ro Mic
°a
3
le
ang
0° at 7
ng
PROV-T3-60LED-BW 12' 60' 48' 1.63 avg 1.63 avg/min 3.3 max 3.3 max/min 1.0 min
50
2
CONFIGURATION: MOUNTING HEIGHT: POLE SPACING: ROADWAY WIDTH: FOOTCANDLES:
at
4
rs
1
4 Aluminum carrier plates dissipate heat away from LED's to the housing assembly
itte
3 Deeply regressed sources maximize efficiency while reducing glare
Em
2 Glare guard perimeter and center reflectors redirect stray light
Individual Factory preset aimingMicroEmitters notches
areQuick-connect easily field changeable. for easy
HOW IT
installation
WORKS
EmitterDeck™ carrier plate
Redirected side-candela Upper parabolic curvature redirects light below pole
(3) High output diodes
MicroEmitter reflector cap
Targeted, precisely controlled LED illumination
Center reflector evenly distributes light below luminaire
Lower parabolic curvature redirects light forward
Redirected side-candela Illustration of a single MicroEmitter at 70° angle
PATENTS PENDING
The exclusive precision aiming system of AAL’s Providence LED ensures that even when looking directly at the luminaire, only one-half of the LEDs can be viewed at any given time. This results in 50% less glare when compared to other exposed, unshielded LED systems. In addition, AAL’s MicroEmitters are aimed at various angles to maximize uniformity, improve comfort, and properly direct illumination to the target zone.
up to 50%
LESS glare Compared to exposed, unshielded LED systems.
PROVIDENCE
®
FAMILY
13
THERMAL MANAGEMENT
LifeShield
TM
Protection System
Advanced Thermal Management with Hubbell's Exclusive LifeShield ™ Protection System
LEDS FOR WARMER ENVIRONMENTS
UNIQUE SUSTAINABLE SOLUTIONS
CONVERT HID TO LED
Providence LED features our exclusive new LifeShield™ Protection System. Each EmitterDeck employs temperature sensors located at the most heat sensitive locations within the LED array. Each sensor sends temperature readings in regular intervals to AAL’s LifeShield monitoring device. LifeShield detects high ambient temperatures and temporarily reduces current slightly to preserve diode life. Lumen output is restored to full capacity once temperatures stabilize within acceptable limits.
AAL's Providence LED is designed for easy installation and
AAL’s exclusive EmitterDeckTM design
upgrading as technology advances. Simple field upgrades
allows for simple upgradability of existing
mean communities can take advantage of the newest LED
AAL luminaires in the field. Think of this
technology without the added expense of removing and
like a personal computer system. The LED
replacing an entire luminaire.
luminaire is the hardware and its easily
• Easy 10-minute field conversion
replaceable EmitterDeck is the software. As LED technology advances and
• Upgrade LEDs as technology advances
becomes even more efficient, AAL’s LED
• Individual MicroEmitters are field replaceable
sustainable solutions will meet the needs
• 60,000+ hours of useful life (L70)
of communities today and in the future.
• Tested under strict LM-79-08 standards • IES-LM-80 compliant LED components
LED VS. HID – ENERGY SAVINGS EXAMPLE Description
Total Luminaire Wattage
Energy Savings (Watt)
Energy Savings (kW)
Energy Savings per Fixture per Year*
PROV LED
72
-
-
-
70W MH
90
18
0.018
$7.88
70W HPS
91
19
0.019
$8.32
100W MH
129
57
0.057
$24.97
100W HPS
130
58
0.058
$25.40
150W MH
164
74
0.074
$32.41
*12 hours per night @ $0.10 per kWh
SIMPLE 10-MINUTE CHANGEOUT
In addition, to maximize cooling surface area, each MicroEmitter incorporates a solid aluminum heat sink, which is fastened to the EmitterDeck’s thick aluminum carrier plate. The EmitterDeck is then affixed to the luminaires’ housing to effectively disperse heat away from the optical chamber. When combined with LifeShield protection, the result is a highly reliable LED system that can withstand operation in even warmer, heat sensitive environments.
STEP 1
Turn off power and remove lamp and reflector asassembly.
STEP 2
Remove existing electronic and ballast components.
STEP 3
Install new LED EmitterDeck, connect wiring plug, and turn on power.
ELEVATED SCALES
24'
21'
18'
15'
12'
9'
6'
3'
Scales ELEVATED
FIXTURE PROS
PROS
2 - PROS
PROV
PROV
PROV
PROV
PROL
PROL
PROV
2 - TRA59U
TRA55
TRA57
TRA56
-
-
TRA56
WMA55
4R12
4R16
4F14
4R20
4F12
5R22
5F18
-
DB1
DB6
DB12
DB3
DB8
DB10
DB2
-
ARM WMA59D TRA59D
POLE -
4F10
BASE COVER -
DB9
PROVIDENCE – LARGE HOUSING SCALE
1
ORDERING INFORMATION PROL
LUMINAIRES
PROL-T2-108LED-WW PROL-T2-108LED-BW PROL-T3-108LED-WW PROL-T3-108LED-BW PROL-T4-108LED-WW PROL-T4-108LED-BW PROL-T5-108LED-WW PROL-T5-108LED-BW
PROL-H2 PROL-H3 PROL-H4 PROL-H5
IES Type 2 distribution. Warm white (3500K). IES Type 2 distribution. Bright white (5100K). IES Type 3 distribution. Warm white (3500K). IES Type 3 distribution. Bright white (5100K). IES Type 4 distribution. Warm white (3500K). IES Type 4 distribution. Bright white (5100K). IES Type 5 distribution. Warm white (3500K). IES Type 5 distribution. Bright white (5100K). 108 light emitting diode array (124 watts). Class 1, 120 thru 277 volt. 350mA drive current.
150PSMH 250PSMH 320PSMH 350PSMH 400PSMH 150HPS 200HPS 250HPS 400HPS
SPK PFN BPS PCA-T HSS
AAL CodeLink
SM
LDL QRS
PROL spec sheet
LARGE TM
Providence LED Large Part of Designer SSL Series
QL
1. LUMINAIRE/LED CONFIGURATION
PROL-T3-108LED-BW
2. LAMP/BALLAST
N/A
3. OPTIONS
SPK
4. COLOR
BLK
5. MOUNTING
TRA57
Type 2 horizontal reflector, flat glass lens Type 3 horizontal reflector, flat glass lens Type 4 horizontal reflector, flat glass lens Type 5 horizontal reflector, flat glass lens
2
3
ORDERING EXAMPLE
LAMP/BALLAST Pulse start 150 watt metal halide 120/208/240/277 volt ballast. Use mogul base, ED-28 lamp. Pulse start 250 watt metal halide 120/208/240/277 volt ballast. Use mogul base, ED-28 lamp. Pulse start 320 watt metal halide 120/208/240/277 volt ballast. Use mogul base, ED-28 lamp. Pulse start 350 watt metal halide 120/208/240/277 volt ballast. Use mogul base, ED-28 lamp. Pulse start 400 watt metal halide 120/208/240/277 volt ballast. Use mogul base, ED-28 lamp. 150 high pressure sodium 120/208/240/277 volt ballast. Use mogul base, ED-23 1/2 lamp. 200 high pressure sodium 120/208/240/277 volt ballast. Use mogul base, ED-18 lamp. 250 high pressure sodium 120/208/240/277 volt ballast. Use mogul base, ED-18 lamp. 400 high pressure sodium 120/208/240/277 volt ballast. Use mogul base ED-18 lamp. All ballasts are factory wired for 277 volts, unless specified. Lamps not included. All applicable ballasts are EISA compliant.
OPTIONS Decorative cast aluminum spikes on the top and bottom of the four vertical struts. Cast aluminum finial painted a brass color. Cast aluminum struts painted a brass color. Spikes also painted brass if chosen. Rotatable photocell housing. House side shield to cut off light behind the pole and shield the lamp from view. HSS not available for Type 5. Factory installed. Not for LED. Lightly diffused lens. Frosted, flat tempered glass lens has a lightly diffused finish to minimize the lamp and reflector brightness. Restrike controller and T-4 mini-can socket will light following power outage until HID reaches full brightness. (Lamp wattage not to exceed ballast wattage). For horizontal reflector only. Not for LED. Socket for T-4 mini-can lamp, field wired to a separate circuit. (Lamp wattage not to exceed ballast wattage). Must be field wired to a separate 120 volt circuit. For horizontal reflector only. Not for LED.
4
COLOR
All 13 standard and 5 premium AAL colors available. For RAL, please submit a 4-digit RAL number or color chip for custom colors.
5
MOUNTING
Select post top mount on a 5" O.D. pole or choose from a wide variety of arms.
SPECIFICATIONS
PHOTOMETRY PROL
PROL CONTOUR PLOT
HOUSING
MICROEMITTER™ REFLECTOR
The fixture housing shall be two-piece die-cast aluminum. The internal reflector module is sealed from the outer housing with a one-piece, memory retentive, molded silicone gasket. The tempered flat glass lens shall be sealed to the housing with a silicone gasket. One recessed stainless steel latch shall release the door to allow access to the LED array.
Precision injection molded, high specular reflectors are positioned to achieve directional control toward desired task for IES cutoff classification. Secondary reflectors with a concave, specular medium hammertone finish are used to redirect light downward. No fasteners are placed on the reflective surface. The entire assembly fastens to the housing as a one-piece module and features wiring quick-connects for easy installation. Standard color temperatures are 3500K and 5100K. Rated luminous efficacy for PROV is >40 lm/W, with rated light output of >2864 for 5100K LED, standard mount. MicroEmitters are field replaceable.
REFLECTOR MODELS – REFLECTOR/LAMP The upper lamp housing shall be die cast aluminum. The internal reflector module is sealed from the outer housing with a one piece, memory retentive, molded silicone gasket. The tempered glass lens shall be sealed to the housing with a silicone gasket. One stainless steel latch shall release the door to allow access to the lamp. The reflector module shall be composed of faceted, specular and semi specular anodized aluminum panels rigidly attached in a die cast aluminum housing. The reflector shall be removed without tools by releasing a pair of steel latches. The reflector tray shall be rotatable on 90° centers for orienting the light distribution. The horizontal reflectors shall meet ANSI-IES standards for full cutoff reflector systems. REFLECTOR MODELS – BALLAST The lower ballast housing shall be cast aluminum. The toolless ballast access for servicing is accomplished by a quarter turn motion of the top cover. The ballast shall be mounted on a prewired tray with a quick disconnect plug attached to the underside of the cover. HID ballasts are high power factor, rated for -30°C starting. Sockets are medium base, G12 for use with T6 lamps or mogul base, pulse rated porcelain. Ballasts are wired at the factory for 277 volts, unless specified.
ELECTRICAL 120 thru 277 volt. All electrical components are mounted directly to the driver tray for maximum heat dissipation. Class 1 electrical classification. 0 - 10v dimming capabilities. LifeShield™ Protection System included for extreme temperature locations (-30°C to 60°C). 120/277 volt Universal with 9mA maximum input current and 1mA maximum drive current. Input power 0.5 watt for 120 volt and 1.25 watt for 277 volt. The onboard surge protector shall be U.L. recognized and have a surge current rating of 10,000 Amps using the industry standard 8/20uSec wave. The surge protector shall have a clamping voltage of 320V and surge rating of 372J. The case shall be a high-temperature, flame resistant plastic enclosure. LED constant current driver operates at 350mA.
180°
PROL T3 Legend:
A=2.00
The large (PROL) Providence shall be factory supplied as a complete, prewired assembly. The PROV fitter shall slip over a 4"/100 mm, the PROL fitter shall slip over a 5"/127 mm open top pole or 4"/100mm arm and be secured and leveled with stainless steel set screws. FINISH Fixture finish consists of a five stage pretreatment regimen with a polymer primer sealer, oven dry off, and top coated with a thermoset super TGIC polyester powder coat finish. The finish shall meet the AAMA 605.2 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance. CERTIFICATION
TYPE 3
B=1.00
C=0.50
D=0.20
E=0.10
100°
100° FORWARD LIGHT
897 lm. 18.1%
0.10
4059 lm. 81.9%
UL
0.50
0.20
1.00 0.50
1.00
0.00
BVH 90°= 0.3%
FVH 90°= 0.8%
BH 80°= 8.0%
FH 80°= 34.4%
BM 60°= 7.9%
FM 60°= 41.8%
BL 30°= 1.9%
FL 30°= 4.9%
Generated by LitePro version 2.026, which is provided and supported by Columbia Lighting, Alera, and Prescolite. Calculations are performed in accordance with IESNA procedures. Columbia, Alera, and Prescolite are not responsible for the light output of lamps and ballasts, or design variables not shown.
Mounting Height: 20' Total flux: 4956 lm Watts: 124 W LPW: 40
0° B1 U1 G1
CONTOUR PLOT TEST #: T27782 CATALOG #: PROL-T5-108LED-BW LAMP: TOTAL LUMENS: -1 LLF: 1.00 ILLUM. UNITS: FC SCALE: 1 IN= 20.0FT
A=2.00
Sep 27, 2010
UP LIGHT 2 lm 0%
NUM LUMS/ ORIENTATION: 1 lum MOUNTING HEIGHT: 20.0' BRACKET ARM LENGTH: 0.0'
PROL T3 Legend:
180°
TYPE 5
B=1.00
C=0.50
D=0.20
E=0.10
100°
UH 100°
BACK LIGHT 0.10
2288 lm. 50.3%
0.20 1.00
WARRANTY
AAL reserves the right to change product specifications without notice.
UH
BACK LIGHT
The fixture shall be listed with ETL for outdoor, wet location use. Conforms to the UL1598 and Canadian CSA Std. C22.2 no.250 standard. IP55.
Providence LED, including housing LEDs and electrical components, is warranted for five years. Providence HID is warranted for 3 years. Any unauthorized return, repair, replacement or modification of the Product(s) shall void this warranty. This warranty applies only to the use of the Product(s) as intended by AAL and does not cover poles, arms, mounting, or any misapplication or misuse of said Product(s), or installation in hazardous or corrosive environments. *Contact AAL for complete warranty language, exceptions, and limitations.
UP LIGHT 0%
Sep 27, 2010
NUM LUMS/ ORIENTATION: 1 lum MOUNTING HEIGHT: 20.0' BRACKET ARM LENGTH: 0.0'
INSTALLATION & MOUNTING
UPGRADE KITS Field replaceable upgrade kits are available for PROL-H reflector models. An entire EmitterDeck assembly, including drivers and 36 LED MicroEmitters (108 diodes) for PROL, is provided. See installation instructions for complete details.
TEST #: T27781 CATALOG #: PROL-T3-108LED-BW LAMP: TOTAL LUMENS: -1 LLF: 1.00 ILLUM. UNITS: FC SCALE: 1 IN= 20.0FT
0.50
FORWARD LIGHT
UL
2259 lm. 49.7%
1.00 0.20
0.20 1.00
0.00
0.20
BVH 90°= 0.9%
FVH 90°= 0.7%
BH 80°= 20.9%
FH 80°= 19.5%
BM 60°= 27.3%
FM 60°= 28.4%
BL 30°= 1.1%
FL 30°= 1.1%
1.00
Generated by LitePro version 2.026, which is provided and supported by Columbia Lighting, Alera, and Prescolite. Calculations are performed in accordance with IESNA procedures. Columbia, Alera, and Prescolite are not responsible for the light output of lamps and ballasts, or design variables not shown.
Mounting Height: 20' Total flux: 4941 lm Watts: 124 W LPW: 36.7
AAL CodeLink
SM
0° B2 U1 G2
BUG Ratings
PROL spec sheet
1
LUMINAIRES
PROV-T2-60LED-WW PROV-T2-60LED-BW PROV-T3-60LED-WW PROV-T3-60LED-BW PROV-T4-60LED-WW PROV-T4-60LED-BW PROV-T5-60LED-WW PROV-T5-60LED-BW
PROV-H2 PROV-H3 PROV-H4 PROV-H5 PROV-V3 PROV-V5 PROV-INDA PROV-INDS
CF
AAL CodeLink
SM
MEDIUM TM
PROV spec sheet
Providence LED Medium Part of Designer SSL Series
2
IES Type 2 distribution. Warm white (3500K). IES Type 2 distribution. Bright white (5100K). IES Type 3 distribution. Warm white (3500K). IES Type 3 distribution. Bright white (5100K). IES Type 4 distribution. Warm white (3500K). IES Type 4 distribution. Bright white (5100K). IES Type 5 distribution. Warm white (3500K). IES Type 5 distribution. Bright white (5100K). 60 light emitting diode array (72 watts). Class 1, 120 thru 277 volt. 350mA drive current. Type 2 horizontal reflector, flat tempered clear glass lens Type 3 horizontal reflector, flat tempered clear glass lens Type 4 horizontal reflector, flat tempered clear glass lens Type 5 horizontal reflector, flat tempered clear glass lens Type 3 vertical reflector, tempered clear sag glass lens Type 5 vertical reflector, tempered clear sag glass lens Asymmetric indirect, indirect reflective optical system, metal halide ED-17 & T6 lamps only Symmetric indirect, indirect reflective optical system, metal halide ED-17 & T6 lamps only
LAMP/BALLAST
Compact fluorescent, electronic 120 thru 277 volt ballast. Use GX24q base, 26, 32 or 42 watt lamp. -180 C minimum starting temp. Direct only. 50MH 50 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 50MHEB 50 watt electronic metal halide 120 thru 277 volt ballast. Use medium base, ED-17 lamp. 70MH 70 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 70MHEB 70 watt electronic metal halide 120 thru 277 volt ballast. Use medium base, ED-17 lamp. 70MHT6 70 watt metal halide 120/277/347 volt ballast. Use G12 base, T-6 ceramic lamp. 70MHT6EB 70 watt electronic metal halide 120 thru 277 volt ballast. Use G12 base, T-6 ceramic lamp. 100MH 100 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 150PSMH Pulse start 150 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 150PSMHT6 Pulse start 150 watt metal halide 120/208/240/277 volt ballast. Use G12 base, T-6 ceramic lamp. 150MHEB 150 watt electronic metal halide 120 or 277 volt ballast. Use medium base, ED-17 lamp. 150MHT6EB 150 watt electronic metal halide 120 or 277 volt ballast. Use G12 base, T-6 ceramic lamp. 175PSMH Pulse start 175 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. For vertical reflector only. 70HPS 70 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 100HPS 100 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 150HPS 150 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 350mA drive current. All ballasts are factory wired for 277 volts, unless specified. Lamps not included. All applicable ballasts are EISA compliant.
ORDERING INFORMATION PROV ORDERING EXAMPLE 1. LUMINAIRE/LED CONFIGURATION 2. LAMP/BALLAST
PROV-T3-60LED-BW N/A
3. OPTIONS
PFN
4. COLOR
WHT
5. MOUNTING
3 SPK PFN BPS PCA-T HSS
LDL
QRS
QL
4
TRA55
OPTIONS Decorative cast aluminum spikes on the top and bottom of the four vertical struts. Cast aluminum finial painted a brass color. Cast aluminum struts painted a brass color. Spikes also painted brass if chosen. Rotatable photocell housing. House side shield to cut off light behind the pole and shield the lamp from view. HSS not available for Type 5. Factory installed. Not for LED. Lightly diffused lens. Frosted, flat tempered glass lens has a lightly diffused finish to minimize the lamp and reflector brightness. Restrike controller and T-4 mini-can socket will light following power outage until HID reaches full brightness. (Lamp wattage not to exceed ballast wattage). For horizontal reflector only. Not for LED. Socket for T-4 mini-can lamp, field wired to a separate circuit. (Lamp wattage not to exceed ballast wattage). Must be field wired to a separate 120 volt circuit. For horizontal reflector only. Not for LED.
COLOR
All 13 standard and 5 premium AAL colors available. For RAL, please submit a 4-digit RAL number or color chip for custom colors.
5
MOUNTING
One-piece cast aluminum arms accept the standard 4" slip fitter on the Providence fixture. The arms are prewired with quick disconnects for easy installation.
SPECIFICATIONS
PHOTOMETRY PROV
PROV
HOUSING The fixture housing shall be two-piece die-cast aluminum. The internal reflector module is sealed from the outer housing with a one-piece, memory retentive, molded silicone gasket. The tempered flat glass lens shall be sealed to the housing with a silicone gasket. One recessed stainless steel latch shall release the door to allow access to the LED array. REFLECTOR MODELS – REFLECTOR/LAMP The upper lamp housing shall be die cast aluminum. The internal reflector module is sealed from the outer housing with a molded silicone gasket. The tempered glass lens shall be sealed to the housing with a silicone gasket. One stainless steel latch shall release the door to allow access the lamp. The reflector module shall be composed of faceted, specular and semi specular anodized aluminum panels rigidly attached in a die cast aluminum housing. The reflector shall be removed without tools by lifting it out of the four spring loaded posts. The reflector tray shall be rotatable on 90° centers for orienting the light distribution. The horizontal and vertical lamp reflectors shall meet ANSI-IES standards for full cutoff reflector systems. REFLECTOR – BALLAST The lower ballast housing shall be die cast aluminum. The toolless ballast access for servicing is accomplished by a quarter turn motion of the top cover. The ballast shall be mounted on a prewired tray with a quick disconnect plug attached to the underside of the cover. HID ballasts are high power factor, rated for -30°C starting. Electronic ballasts for metal halide lamps are sound rated A. Sockets are medium base for ED-17 lamps, G12 for use with T6 lamps, All HID sockets are pulse rated porcelain. Ballasts are wired at the factory for 277 volts, unless specified. Compact fluorescent transformers shall accept 120 to 277 volt input and rated for -18°C starting. INDIRECT MODELS – LOWER LAMP MODULE The lower housing shall contain the lamp module. The cover shall be die cast aluminum with a tempered glass lens. The lamp shall be accessed by turning the lamp housing cover a quarter turn. The reflector shall be polished, anodized aluminum with an extremely narrow beam for directing the light to the upper reflector. Sockets are medium base for ED-17 lamps or G12 for use with T6 lamps, All sockets are pulse rated porcelain. INDIRECT MODELS – UPPER REFLECTOR/BALLAST The die cast aluminum upper housing shall contain the ballast assembly and the indirect reflector. The ballast shall be mounted on a prewired tray with a quick disconnect plug. The HID ballasts are high power factor, rated for -30°C starting. Ballasts are wired at the factory for 277 volts, unless specified. The indirect reflector is mounted to the underside of the upper housing. The reflector shall be die cast aluminum, finished in a high reflectance white. The indirect reflector models shall be IES classified as cutoff with less than 1% lumen output above 90 degrees. UPGRADE KITS Field replaceable upgrade kits are available for PROV-H reflector models. An entire EmitterDeck assembly, including drivers and 20 LED MicroEmitters (60 diodes) for PROV, is provided. See installation instructions for complete details.
ELECTRICAL 120 thru 277 volt. All electrical components are mounted directly to the driver tray for maximum heat dissipation. Class 1 electrical classification. 0 - 10v dimming capabilities. LifeShield™ Protection System included for extreme temperature locations (-30°C to 60°C). 120/277 volt Universal with 9mA maximum input current and 1mA maximum drive current. Input power 0.5 watt for 120 volt and 1.25 watt for 277 volt. The onboard surge protector shall be U.L. recognized and have a surge current rating of 10,000 Amps using the industry standard 8/20uSec wave. The surge protector shall have a clamping voltage of 320V and surge rating of 372J. The case shall be a high-temperature, flame resistant plastic enclosure. LED constant current driver operates at 350mA. MICROEMITTER™ REFLECTOR Precision injection molded, high specular reflectors are positioned to achieve directional control toward desired task for IES cutoff classification. Secondary reflectors with a concave, specular medium hammertone finish are used to redirect light downward. No fasteners are placed on the reflective surface. The entire assembly fastens to the housing as a one-piece module and features wiring quick-connects for easy installation. Standard color temperatures are 3500K and 5100K. Rated luminous efficacy for PROV is >40 lm/W, with rated light output of >2864 for 5100K LED, standard mount. MicroEmitters are field replaceable. INSTALLATION & MOUNTING The Medium (PROV) Providence shall be factory supplied as a complete, prewired assembly. The PROV fitter shall slip over a 4"/100 mm, the PROV fitter shall slip over a 5"/127 mm open top pole or 4"/100mm arm and be secured and leveled with stainless steel set screws. FINISH Fixture finish consists of a five stage pretreatment regimen with a polymer primer sealer, oven dry off, and top coated with a thermoset super TGIC polyester powder coat finish. The finish shall meet the AAMA 605.2 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance CERTIFICATION The fixture shall be listed with ETL for outdoor, wet location use. Conforms to the UL1598 and Canadian CSA Std. C22.2 no.250 standard. IP55. WARRANTY Providence LED, including housing LEDs and electrical components, is warranted for five years. Providence HID is warranted for 3 years. Any unauthorized return, repair, replacement or modification of the Product(s) shall void this warranty. This warranty applies only to the use of the Product(s) as intended by AAL and does not cover poles, arms, mounting, or any misapplication or misuse of said Product(s), or installation in hazardous or corrosive environments. *Contact AAL for complete warranty language, exceptions, and limitations. AAL reserves the right to change product specifications without notice. AAL CodeLink
SM
CONTOUR PLOT TEST #: PROV-T3-60LED-BW CATALOG #: PROV-T3-60LED-BW LAMP: TOTAL LUMENS: -1 LLF: 1.00 ILLUM. UNITS: FC SCALE: 1 IN= 12.0FT
0 lm. 0%
PROV T3 Legend:
A=5.00
Sep 22, 2010
NUM LUMS/ ORIENTATION: 1 lum MOUNTING HEIGHT: 12.0' BRACKET ARM LENGTH: 0.0'
TYPE 3
B=2.00
C=1.00
D=0.50
180°
E=0.25
100°
UH 100°
BACK LIGHT 0.25
FORWARD LIGHT
516 lm. 15.4% 0.50
2.00 0.00
Generated by LitePro version 2.026, which is provided and supported by Columbia Lighting, Alera, and Prescolite. Calculations are performed in accordance with IESNA procedures. Columbia, Alera, and Prescolite are not responsible for the light output of lamps and ballasts, or design variables not shown.
Mounting Height: 12' Total flux: 3341 lm Watts: 72.4 W LPW: 46
BVH 90°= 0.2%
FVH 90°= 0.7%
BH 80°= 6.3%
FH 80°= 25.9%
BM 60°= 7.5%
FM 60°= 51.5%
BL 30°= 1.3%
FL 30°= 6.4%
0° B1 U1 G1 CONTOUR PLOT TEST #: PROV-T3-60LED-BW CATALOG #: PROV-T3-60LED-BW LAMP: TOTAL LUMENS: -1 LLF: 1.00 ILLUM. UNITS: FC SCALE: 1 IN= 12.0FT
PROV T5 Legend:
A=5.00
B=2.00
Sep 22, 2010
NUM LUMS/ ORIENTATION: 1 lum MOUNTING HEIGHT: 12.0' BRACKET ARM LENGTH: 0.0'
UP LIGHT 0 lm. 0%
180°
TYPE 5 C=1.00
D=0.50
E=0.25
100°
UH 100°
BACK LIGHT 1562 lm. 50%
0.50 0.25
FORWARD LIGHT
UL
1502 lm. 50%
1.00 2.00 0.00
BVH 90°=0.8%
FVH 90°= 0.8%
BH 80°= 19.0%
FH 80°= 19.4%
BM 60°= 22.7%
FM 60°= 22.3%
BL 30°= 7.5%
FL 30°= 7.5%
Generated by LitePro version 2.026, which is provided and supported by Columbia Lighting, Alera, and Prescolite. Calculations are performed in accordance with IESNA procedures. Columbia, Alera, and Prescolite are not responsible for the light output of lamps and ballasts, or design variables not shown.
Mounting Height: 12' Total flux: 3124 lm Watts: 71 W LPW: 44
0° B2 U1 G2
PROV spec sheet
2825.4 lm. 84.9%
UL
5.00
1.00
1
LUMINAIRES
ORDERING INFORMATION PROS
PROS-X
Horizontal LED.
PROS-DIRS
Symmetric direct reflective optical system. Full cutoff
ORDERING EXAMPLE
PROS-INDA
Asymmetric indirect reflective optical system, 20 watt Mini Mastercolor only.
1. LUMINAIRE
Symmetric indirect reflective optical system, 20 watt Mini Mastercolor only.
3. OPTIONS
SPK
4. COLOR
BLK
PROS-INDS
2. LAMP/BALLAST
5. MOUNTING
2
TRA59D
18LED-WW
18 light emitting diode array (16.4 watts). Warm white (3500K). IES Type 1. 120 thru 277 volt.
18LED-BW
18 light emitting diode array (16.4 watts). Bright white (5100K). IES Type 1. 120 thru 277 volt.
27LED-WW
27 light emitting diode array (33.6 watts). Warm white (3500K). IES Type 3. 120 thru 277 volt.
27LED-BW
27 light emitting diode array (33.6 watts). Bright white (5100K). IES Type 3. 120 thru 277 volt.
36LED-WW
36 light emitting diode array (32.7 watts). Warm white (3500K). IES Type 5. 120 thru 277 volt.
36LED-BW
36 light emitting diode array (32.7 watts). Bright white (5100K). IES Type 5. 120 thru 277 volt.
20MMC
20 watt electronic metal halide 120 thru 277 volt ballast. Use PGJ5 base, Mini Mastercolor lamp.
39MMC
39 watt electronic metal halide 120 thru 277 volt ballast. Use PGJ5 base, Mini Mastercolor lamp.
39MHT6EB
39 watt electronic metal halide 120 thru 277 volt ballast. Use G12 base, T-6 ceramic lamp.
70MHT6EB
70 watt electronic metal halide 120 thru 277 volt ballast. Use G12 base, T-6 ceramic lamp.
CF
Compact fluorescent, electronic ballast 120 thru 277 volt. Use GX24q base, 26, 32 or 42 watt lamp. Specify wattage. -18°C minimum starting temp
3 SPK PFN BPS HSS
LDL
4
OPTIONS Decorative cast aluminum spikes on the top and bottom of the four vertical struts. Cast aluminum finial painted a brass color. Cast aluminum struts painted a brass color. Spikes also painted brass if chosen. House side shield to cut off light behind the pole and shield the lamp from view. HSS not available for Type 5. Factory installed. Not for LED. Lightly diffused lens. Frosted, flat tempered glass lens has a lightly diffused finish to minimize the lamp and reflector brightness. Not for LED.
COLOR
All 13 standard and 5 premium AAL colors available. For RAL, please submit a 4-digit RAL number or color chip for custom colors.
5
MOUNTING
One-piece cast aluminum arms accept the standard 3" slip fitter on the Providence fixture. The arms are prewired with quick disconnects. Wall mounted arms do not include wall mounting hardware. Pole mounted arms use 3/8-16 hardware bolts for attaching to the pole.
SM
PROS spec sheet
20MMC
LAMP/BALLAST
All ballasts are factory wired for 277 volts unless specified. Lamps not included, except LED option. All applicable ballasts are EISA compliant
AAL CodeLink
PROS - INDS
SMALL
SPECIFICATIONS
REFLECTOR MODELS - REFLECTOR/LAMP
INSTALLATION & MOUNTING The PROS shall be factory supplied as a complete, prewired assembly. The fixture shall slip over a 3"/75mm open top pole or 4"/100mm pole mounted arm and secured and leveled with 3 stainless steel set screws.
The upper lamp housing shall be die cast aluminum. The internal reflector module is sealed from the outer housing with a one piece, memory retentive, molded silicone gasket. The tempered glass lens shall be sealed to the housing with a silicone gasket. One stainless steel latch shall release the door to allow access to the lamp.
FINISH
The reflector module shall be composed of a spun, specular aluminum panel rigidly attached in a die cast aluminum housing. The horizontal lamp reflectors (DIRS) shall meet ANSI-IES standards for full cutoff reflector systems.
Fixture finish consists of a five stage pretreatment regimen with a polymer primer sealer, oven dry off and top coated with a thermoset super TGIC polyester powder coat finish. The finish shall meet the AAMA 605.2 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance.
REFLECTOR MODELS - BALLAST The lower ballast housing shall be cast aluminum. The tool-less ballast access for servicing is accomplished by a quarter turn motion of the top cover. The ballast shall be mounted on a prewired tray with a quick disconnect plug attached to the underside of the cover. HID ballasts are high power factor, rated for -30°C starting. Electronic ballasts for metal halide lamps are sound rated A. Sockets are medium base, G12 for use with T6 lamps. All sockets are pulse rated porcelain. Ballasts are wired at the factory for 277 volts, unless specified. Compact fluorescent transformers shall accept 120 thru 277 volt input and rated for -18°C starting. The LED driver accepts 120 thru 277 volt input.
INDIRECT MODELS - LOWER LAMP MODULE The lower housing shall contain the lamp module. The cover shall be die cast aluminum with a tempered glass lens. The lamp shall be accessed by turning the lamp housing cover a quarter turn. The reflector shall be polished, anodized aluminum with an extremely narrow beam for directing the light to the upper reflector. Sockets are PGJ5 for use with BT-5 lamps. All sockets are pulse rated porcelain.
INDIRECT MODELS - UPPER REFLECTOR/BALLAST The die cast aluminum upper housing shall contain the ballast assembly and the indirect reflector. The ballast shall be mounted on a prewired tray with a quick disconnect plug. The HID ballasts are high power factor, rated for -30°C starting. Ballasts are multi-tap, wired at the factory for 277 volts. The indirect reflector is mounted to the underside of the upper housing. The reflector shall be die cast aluminum, finished in a high reflectance white. The indirect reflector models shall be IES classified as cutoff with less than 1% lumen output above 90 degrees.
PROSPhotometry PROSPhotometry
PROS
PROS PHOTOMETRY PROS PROS PHOTOMETRY PHOTOMETRY
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in FIXTURE SETBACK (in feet) FIXTURE20SETBACK 16 22 (in feet) 24 16 20 22 24 16 20 22 24 WATTAGE WATTAGE WATTAGE 250 1 0.64 0.53 0.44 250 1 0.64 0.53 0.44 250 Multiply 1 0.64 0.53 on isoline 0.44 How to to use: use: factor by fc fc value value How Multiply factor by on isoline How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in FIXTURE SETBACK (in feet) FIXTURE12SETBACK 10 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE WATTAGE 20MMC 1 0.69 0.51 0.39 20MMC 1 0.69 0.51 0.39 20MMC 1 0.69 0.51 on isoline 0.39 How to to use: use: Multiply Multiply factor by fc fc value value How factor by on isoline How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) FIXTURE24SETBACK 20 26 (in feet) 30 20 24 26 30 20 24 26 30 WATTAGE WATTAGE WATTAGE 400 0.69 0.59 0.44 400 11 0.69 0.59 0.44 400 Multiply 1 0.69 0.59 on isoline 0.44 How to to use: use: factor by fc fc value value How Multiply factor by on isoline How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) FIXTURE12SETBACK 10 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE WATTAGE 70MHT6 0.69 0.51 0.39 70MHT6 11 0.69 0.51 0.39 70MHT6 1 0.69 0.51 on isoline 0.39 How to to use: use: Multiply Multiply factor by fc fc value value How factor by on isoline How to use: Multiply factor by fc value on isoline
PHOTOMETRY PROS
PROS-H5 42 CFL - HSS
PROS-H5 42 WATT CFL LAMP
CONVERSION TABLE TABLE CONVERSION CONVERSION TABLETABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK=(in (in FIXTURE SETBACK feet) HT 1.0 LLF, GRIDLINES MTG. FIXTURE 10 12SETBACK 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE FIXTURE MTG. HT. (IN FEET) WATTAGE 42CF 0.69 0.51 0.39 42CF 11 0.69 0.51 0.39 42CF 1 10 0.69 0.51 on 0.39 How to use: use: Multiply Multiply factor by12 fc value value isoline 14isoline 16 WATTAGE How to factor by fc on How to use: Multiply factor by fc value on isoline
.25 .25 .25
11 1
11 1
42CF
.5.5 .5
22 2
1.00
0.69
0.51
0.39
.5.5 .5 22 2 .25 .25 .25
CERTIFICATION The fixture shall be listed with ETL for outdoor, wet location use, UL1598 and Canadian CSA Std. C22.2 no.250. IP=55.
ARCHITECTURALAREA AREALIGHTING LIGHTING ARCHITECTURAL PROS-H5-42CFL PROS-H5-42CFL ARCHITECTURAL AREA LIGHTING PROVIDENCEFULL FULLCUT-OFF CUT-OFFPOST POSTTOP TOPLUMINAIRE LUMINAIRE PROVIDENCE PROS-H5-42CFL WITHSPECULAR SPECULARRELFECTOR RELFECTORAND ANDCLEAR CLEARFLAT FLAT WITH PROVIDENCE FULL CUT-OFF POST TOP LUMINAIRE GLASSLENS LENS GLASS WITH SPECULAR RELFECTOR AND CLEAR FLAT ONE42 42WATT WATT CFL LAMP ONE GLASS LENS CFL LAMP LUMENS=3200 LUMENS=3200 ONE 42 WATT CFL LAMP LUMENS=3200
WARRANTY
HorizontalFootcandles Footcandles Horizontal Scale:11Inch Inch==88Ft. Ft. Scale: Horizontal Footcandles LightLoss Loss Factor==1.00 1.00 Light Scale:Factor 1 Inch = 8 Ft. TotalLumens LumensPer PerLuminaire Luminaire==3200 3200 Total Light Loss Factor = 1.00 MountingHeight Height==10.00 10.00Ft Ft Mounting Total Lumens Per Luminaire = 3200 MaximumCalculated CalculatedValue Value==6.64 6.64 Fc Maximum Mounting Height = 10.00Fc Ft Arrangement:Single Single Arrangement: Maximum Calculated Value = 6.64 Fc Arrangement: Single
PhotometricToolbox ToolboxProfessional ProfessionalEdition Edition(c) (c)copyright copyright1995-2004 1995-2004by byLighting LightingAnalysts, Analysts,Inc. Inc. Photometric Calculationsbased basedon onpublished publishedIES IESMethods Methodsand andrecommendations. recommendations. Calculations Photometric Toolbox Professional Edition (c) copyright 1995-2004 by Lighting Resultsderived derived fromcontent contentofofmanufacturers manufacturers IESformat format photometric file. Analysts, Inc. Results from IES photometric file. Calculations based on published IES Methods and recommendations.
PROS-H5 70MH WATT CMH - T6 LAMP Results derived from content of manufacturers IES format photometric file.
Fixture is warranted for three years. Ballast components carry the ballast manufacturer’s limited warranty. Any unauthorized return, repair, replacement or modification of the Product(s) shall void this warranty. This warranty applies only to the use of the Product(s) as intended by AAL and does not cover any misapplication or misuse of said Product(s), or installation in hazardous or corrosive environments. Contact AAL for complete warranty language, exceptions, and limitations.
.25 .25 .25
22 2
ARCHITECTURALAREA AREALIGHTING LIGHTING ARCHITECTURAL PROS-H5-42CFL-HSS PROS-H5-42CFL-HSS ARCHITECTURAL AREA LIGHTING PROVIDENCEFULL FULLCUT-OFF CUT-OFFPOST POSTTOP TOPLUMINAIRE LUMINAIRE PROVIDENCE PROS-H5-42CFL-HSS WITHSPECULAR SPECULARRELFECTOR RELFECTORAND ANDCLEAR CLEARFLAT FLAT WITH PROVIDENCE FULL CUT-OFF POST TOP LUMINAIRE GLASSLENS LENS GLASS WITH SPECULAR RELFECTOR AND CLEAR FLAT WITHHOUSE HOUSESIDE SIDESHIELD SHIELD WITH GLASS LENS ONE 42WATT WATTCFL CFLLAMP LAMP ONE WITH42 HOUSE SIDE SHIELD LUMENS=3200 LUMENS=3200 ONE 42 WATT CFL LAMP LUMENS=3200
Horizontal Footcandles
Horizontal Footcandles Scale:11Inch Inch==88Ft. Ft. CONVERSION TABLE TABLE Scale: CONVERSION Horizontal Footcandles LightLoss Loss Factor==1.00 1.00 Light Scale:Factor 1 Inch = 8 Ft. TABLE TotalLumens LumensPer PerLuminaire Luminaire==3200 3200 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht.Total Light Loss Factor = 1.00 1.0 00 tilt, Ht. MountingHeight Height==10.00 10.00Ft Ft Mounting Total Lumens Per Luminaire = 3200 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) MaximumCalculated CalculatedValue Value==4.70 4.70Fc Fc Maximum Mounting Height = 10.00 Ft FIXTURE SETBACK (in FIXTURE SETBACK (in feet) Arrangement:Single Single Arrangement: Maximum Calculated Value = 4.70 Fc FIXTURE20SETBACK 16 22 (in feet) 24 Arrangement: Single 16 20 22 24 16 20 22 24 WATTAGE WATTAGE WATTAGE 250 0.64 0.53 0.44 250 11 0.64 0.53 0.44 250 1 0.64 0.53 0.44 How to to use: use: Multiply Multiply factor factor by by fc fc value value on on isoline isoline How How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in FIXTURE SETBACK (in feet) FIXTURE12SETBACK 10 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE WATTAGE 20MMC 0.69 0.51 0.39 20MMC 11 0.69 0.51 0.39 20MMC 1 0.69 0.51 on isoline 0.39 How to to use: use: Multiply Multiply factor by fc fc value value How factor by on isoline How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) FIXTURE SETBACK (in feet) 20 24 26 30 20 24 26 30 20 24 26 30 WATTAGE .25 WATTAGE .25 WATTAGE .25 400 0.69 0.59 0.44 400 11 0.69 0.59 0.44 1 1 400 Multiply 1 0.69 0.59 0.44 1 on How to to use: use: factor by fc fc value value on isoline isoline How Multiply factor by How to use: Multiply factor by fc value on isoline.5
CONVERSION TABLE TABLE CONVERSION TABLE TABLE CONVERSION 1.0 lff, lff,CONVERSION tilt, grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, grid Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) 1.0 LLF, GRIDLINES = MTG. HT FIXTURE SETBACK (in feet) 10 12 14 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE FIXTURE MTG. HT. (IN FEET) WATTAGE 70MHT6 0.69 0.51 0.39 70MHT6 11 0.69 0.51 0.39 70MHT6 1 0.69 0.51 on isoline 0.39 How to use: use: Multiply Multiply factor by fc fc value How to factor by value on14 isoline 10 12 16 WATTAGE How to use: Multiply factor by fc value on isoline
PhotometricToolbox ToolboxProfessional ProfessionalEdition Edition(c) (c)copyright copyright1995-2004 1995-2004by byLighting LightingAnalysts, Analysts,Inc. Inc. Photometric Calculationsbased basedon onpublished publishedIES IESMethods Methodsand andrecommendations. recommendations. Calculations Photometric Toolbox Professional Edition (c) copyright 1995-2004 by Lighting Resultsderived derived fromcontent contentofofmanufacturers manufacturers IESformat format photometric file. Analysts, Inc. Results from IES photometric file. Calculations based on published IES Methods and recommendations.
PROS-H5-70MH-HSS 70 WATT CMH - T6 LAMP
Results derived from content of manufacturers IES format photometric file.
22 2
.5 .5
AAL reserves the right to change product specifications without notice.
11 1
ARCHITECTURALAREA AREALIGHTING LIGHTING ARCHITECTURAL PROS-H5-70MH PROS-H5-70MH ARCHITECTURAL AREA LIGHTING PROVIDENCEFULL FULLCUT-OFF CUT-OFFPOST POSTTOP TOPLUMINAIRE LUMINAIRE PROVIDENCE PROS-H5-70MH WITHSPECULAR SPECULARRELFECTOR RELFECTORAND ANDCLEAR CLEARFLAT FLAT WITH PROVIDENCE FULL CUT-OFF POST TOP LUMINAIRE GLASSLENS LENS GLASS WITH SPECULAR RELFECTOR AND CLEAR FLAT ONE GE 70 WATT CMH T6 LAMPG12E G12EBASE BASE ONE GELENS 70 WATT CMH T6 LAMP GLASS LUMENS=6200 LUMENS=6200 ONE GE 70 WATT CMH T6 LAMP G12E BASE LUMENS=6200
AAL CodeLink
HorizontalFootcandles Footcandles Horizontal Scale:11Inch Inch==88Ft. Ft. Scale: Horizontal Footcandles LightLoss Loss Factor==1.00 1.00 Light Scale:Factor 1 Inch = 8 Ft. TotalLumens LumensPer PerLuminaire Luminaire==6500 6500 Total Light Loss Factor = 1.00 MountingHeight Height==10.00 10.00Ft Ft Mounting Total Lumens Per Luminaire = 6500 Maximum Calculated Value = 46.79Fc Fc Maximum Calculated Mounting Value Height==46.79 10.00 Ft Arrangement:Single Single Arrangement: Maximum Calculated Value = 46.79 Fc Arrangement: Single
PROS-INDA 20MH WATT CMH- - T4.5 LAMP
PhotometricToolbox ToolboxProfessional ProfessionalEdition Edition(c) (c)copyright copyright1995-2004 1995-2004by byLighting LightingAnalysts, Analysts,Inc. Inc. Photometric Calculationsbased basedon onpublished publishedIES IESMethods Methodsand andrecommendations. recommendations. Calculations Photometric Toolbox Professional Edition (c) copyright 1995-2004 by Lighting Resultsderived derived fromcontent contentofofmanufacturers manufacturers IESformat format photometric file. Analysts, Inc. Results from IES photometric file. Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file.
SM
PROS spec sheet .25 .25 .25
ARCHITECTURALAREA AREALIGHTING LIGHTING ARCHITECTURAL PROS-INDA-20MH PROS-INDA-20MH ARCHITECTURAL AREA LIGHTING PROVIDENCEPOST POSTTOP TOPLUMINAIRE LUMINAIREWITH WITH PROVIDENCE PROS-INDA-20MH SEMI-SPECULAR SEMI-SPECULAR PROVIDENCE POST TOP LUMINAIRE WITH RELFECTORAND ANDCLEAR CLEARFLAT FLATGLASS GLASSLENS LENS RELFECTOR SEMI-SPECULAR ONE20 20WATT WATTCMH CMHT4.5 T4.5LAMP LAMPG8.5E G8.5EBASE BASE ONE RELFECTOR AND CLEAR FLAT GLASS LENS LUMENS=1700 LUMENS=1700 ONE 20 WATT CMH T4.5 LAMP G8.5E BASE LUMENS=1700
28 28 28
70MHT6
1.00
0.69
0.51
0.39
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK SETBACK (in (in FIXTURE feet) FIXTURE12SETBACK 10 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE WATTAGE 42CF 0.69 0.51 0.39 42CF 11 0.69 0.51 0.39 42CF 1 0.69 0.51 on isoline 0.39 How to to use: use: Multiply Multiply factor by fc fc value value How factor by on isoline How to use: Multiply factor by fc value on isoline
.5.5 .5
PhotometricToolbox ToolboxProfessional ProfessionalEdition Edition(c) (c)copyright copyright1995-2004 1995-2004by byLighting LightingAnalysts, Analysts,Inc. Inc. Photometric Calculationsbased basedon onpublished publishedIES IESMethods Methodsand andrecommendations. recommendations. Calculations Photometric Toolbox Professional Edition (c) copyright 1995-2004 by Lighting Resultsderived derived fromcontent contentofofmanufacturers manufacturers IESformat format photometric file. Analysts, Inc. Results from IES photometric file. Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file.
HorizontalFootcandles Footcandles Horizontal Scale:11Inch Inch==88Ft. Ft. Scale: Horizontal Footcandles LightLoss Loss Factor==1.00 1.00 Light Scale:Factor 1 Inch = 8 Ft. TotalLumens LumensPer PerLuminaire Luminaire==1700 1700 Total Light Loss Factor = 1.00 MountingHeight Height==10.00 10.00Ft Ft Mounting Total Lumens Per Luminaire = 1700 MaximumCalculated CalculatedValue Value==0.31 0.31 Fc Maximum Mounting Height = 10.00Fc Ft Arrangement: Single Arrangement: Single Maximum Calculated Value = 0.31 Fc Arrangement: Single
ARCHITECTURALAREA AREALIGHTING LIGHTING ARCHITECTURAL PROS-H5-70MH-HSS PROS-H5-70MH-HSS ARCHITECTURAL AREA LIGHTING PROVIDENCEFULL FULLCUT-OFF CUT-OFFPOST POSTTOP TOPLUMINAIRE LUMINAIRE PROVIDENCE PROS-H5-70MH-HSS WITHSPECULAR SPECULARRELFECTOR RELFECTORAND ANDCLEAR CLEARFLAT FLAT WITH PROVIDENCE FULL CUT-OFF POST TOP LUMINAIRE GLASSLENS LENS GLASS WITH SPECULAR RELFECTOR AND CLEAR FLAT WITH HOUSE SIDE SHIELD WITH HOUSE GLASS LENS SIDE SHIELD ONE 70WATT WATTCMH CMHT6 T6LAMP LAMPG12E G12EBASE BASE ONE WITH70 HOUSE SIDE SHIELD LUMENS=6200 LUMENS=6200 ONE 70 WATT CMH T6 LAMP G12E BASE LUMENS=6200
HorizontalFootcandles Footcandles Horizontal Scale:11Inch Inch==88Ft. Ft. Scale: Horizontal Footcandles LightLoss Loss Factor==1.00 1.00 Light Scale:Factor 1 Inch = 8 Ft. TotalLumens LumensPer PerLuminaire Luminaire==6500 6500 Total Light Loss Factor = 1.00 MountingHeight Height==10.00 10.00Ft Ft Mounting Total Lumens Per Luminaire = 6500 Maximum Calculated Value = 24.77 Fc Maximum Calculated Mounting Value Height==24.77 10.00Fc Ft Arrangement:Single Single Arrangement: Maximum Calculated Value = 24.77 Fc Arrangement: Single
PROS-INDS-20MH 20 WATT CMH- - T4.5 LAMP PhotometricToolbox ToolboxProfessional ProfessionalEdition Edition(c) (c)copyright copyright1995-2004 1995-2004by byLighting LightingAnalysts, Analysts,Inc. Inc. Photometric Calculationsbased basedon onpublished publishedIES IESMethods Methodsand andrecommendations. recommendations. Calculations Photometric Toolbox Professional Edition (c) copyright 1995-2004 by Lighting Resultsderived derived fromcontent contentofofmanufacturers manufacturers IESformat format photometric file. Analysts, Inc. Results from IES photometric file. Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file.
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) FIXTURE20SETBACK 16 22 (in feet) 24 16 20 22 24 16 20 22 24 WATTAGE WATTAGE WATTAGE 250 0.64 0.53 0.44 250 11 0.64 0.53 0.44 250 Multiply 1 0.64 0.53 on isoline 0.44 How to to use: use: factor by fc fc value value How Multiply factor by on isoline How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION CONVERSION TABLE TABLE 1.0 lff, lff,CONVERSION tilt, grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, grid Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in FIXTURE SETBACK feet) HT 1.0 LLF, GRIDLINES =(inMTG. FIXTURE 10 12SETBACK 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE FIXTURE MTG. HT. (IN FEET) WATTAGE 20MMC 0.69 0.51 0.39 20MMC 11 0.69 0.51 0.39 20MMC 1 0.69 0.51 on isoline 0.39 How to use: use: Multiply Multiply factor by fc fc value 10 12 16 How to factor by value on14 isoline WATTAGE How to use: Multiply factor by fc value on isoline
.25 CONVERSION TABLE .25 CONVERSION TABLE .25 TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) FIXTURE24SETBACK (in feet) 20 26 30 20 24 26 30 20 24 26 30 WATTAGE WATTAGE WATTAGE 400 0.69 0.59 0.44 400 11 0.69 0.59 0.44 400 Multiply 1 0.69 0.59 on isoline 0.44 How to to use: use: factor by fc fc value value How Multiply factor by on isoline How to use: Multiply factor by fc value on isoline
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in (in FIXTURE SETBACK feet) FIXTURE12SETBACK (in feet) 10 14 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE WATTAGE 70MHT6 0.69 0.51 0.39 70MHT6 11 0.69 0.51 0.39 70MHT6 1 0.69 0.51 on isoline 0.39 How to to use: use: Multiply Multiply factor by fc fc value value How factor by on isoline How to use: Multiply factor by fc value on isoline
ARCHITECTURALAREA AREALIGHTING LIGHTING ARCHITECTURAL PROS-INDS-20MH PROS-INDS-20MH ARCHITECTURAL AREA LIGHTING PROVIDENCEPOST POSTTOP TOPLUMINAIRE LUMINAIREWITH WITH PROVIDENCE PROS-INDS-20MH SEMI-SPECULAR SEMI-SPECULAR PROVIDENCE POST TOP LUMINAIRE WITH RELFECTORAND ANDCLEAR CLEARFLAT FLATGLASS GLASSLENS LENS RELFECTOR SEMI-SPECULAR ONE20 20WATT WATTCMH CMHT4.5 T4.5LAMP LAMPG8.5E G8.5EBASE BASE ONE RELFECTOR AND CLEAR FLAT GLASS LENS LUMENS=1700 LUMENS=1700 ONE 20 WATT CMH T4.5 LAMP G8.5E BASE LUMENS=1700
PhotometricToolbox ToolboxProfessional ProfessionalEdition Edition(c) (c)copyright copyright1995-2004 1995-2004by byLighting LightingAnalysts, Analysts,Inc. Inc. Photometric Calculationsbased basedon onpublished publishedIES IESMethods Methodsand andrecommendations. recommendations. Calculations Photometric Toolbox Professional Edition (c) copyright 1995-2004 by Lighting Resultsderived derived fromcontent contentofofmanufacturers manufacturers IESformat format photometric file. Analysts, Inc. Results from IES photometric file. Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file.
HorizontalFootcandles Footcandles Horizontal Scale:11Inch Inch==88Ft. Ft. Scale: Horizontal Footcandles LightLoss Loss Factor==1.00 1.00 Light Scale:Factor 1 Inch = 8 Ft. TotalLumens LumensPer PerLuminaire Luminaire==1700 1700 Total Light Loss Factor = 1.00 MountingHeight Height==10.00 10.00Ft Ft Mounting Total Lumens Per Luminaire = 1700 MaximumCalculated CalculatedValue Value==0.34 0.34 Fc Maximum Mounting Height = 10.00Fc Ft Arrangement: Single Arrangement: Single Maximum Calculated Value = 0.34 Fc Arrangement: Single
20MMC
1.00
0.69
0.51
CONVERSION TABLE TABLE CONVERSION TABLE 1.0 lff, lff,CONVERSION tilt, grid grid increment=mtg. increment=mtg. Ht. 1.0 00 tilt, Ht. 1.0 lff, 0 tilt, grid increment=mtg. Ht.feet) FIXTURE SETBACK (in FIXTURE SETBACK (in feet) FIXTURE12SETBACK 10 14 (in feet) 16 10 12 14 16 10 12 14 16 WATTAGE WATTAGE WATTAGE 42CF 1 0.69 0.51 0.39 42CF 1 0.69 0.51 0.39 42CF 1 0.69 0.51 on isoline 0.39 How to to use: use: Multiply Multiply factor by fcI value value How P factor RO O by D EEon Nisoline C EE®® P R VV fc I D N C How to use: Multiply P factor R O by V fcI value D E on N isoline C E®
0.39
1
LUMINAIRES
PROB
ORDERING INFORMATION PROB
Symmetric horizontal optical system
ORDERING EXAMPLE
2
AAL CodeLink
SM
PROB spec sheet
BOLLARD
LAMP/BALLAST
20MMC
20 watt electronic metal halide 120/277 volt ballast. Use a PGJ5 base, Mini MasterColor® lamp.
39MMC
39 watt electronic metal halide 120/277 volt ballast. Use a PGJ5 base, Mini MasterColor® lamp.
39MHT6EB
39 watt electronic metal halide 120 thru 277 volt ballast. Use a G12 base, T6 ceramic lamp.
50MH
50 watt metal halide 120/277 volt ballast. Use a medium base, ED-17 lamp.
50MHEB
50 watt electronic metal halide 120 thru 277 volt ballast. Use a medium base, ED-17 lamp.
1. LUMINAIRE
PROB
2. LAMP/BALLAST
50MH
3. OPTIONS
HSS
4. COLOR
BLK
5. MOUNTING
PM
3
OPTIONS
HSS
House Side Shield. Not available with LED.
LDL
Lightly Diffused Lens
BBU
Battery backup powers the lamp for up to ninety minutes during a power failure Output of the 32 watt lamp will be 575 lumens. Output from the 42 watt lamp will be 750 lumens. Operating temperature 0ºC to 55ºC. For use with CF only. Integral.
70MH
70 watt metal halide 120/208/240/277 volt ballast. Use a medium base, ED-17 lamp.
70MHT6
70 watt metal halide 120/208/240/277 volt ballast. Use a G12 base, T6 ceramic lamp.
70MHEB
70 watt electronic metal halide 120 thru 277 volt ballast. Use medium base, ED-17 lamp.
PFC
Painted brass finial cap
BPS
Painted brass struts
70MHT6EB
70 watt electronic metal halide ballast, 120 thru 277 volt. Use a G12 base, T6 lamp.
DSC
Dark sky cap. Matte black body cap (shown at right).
100MH
100 watt metal halide 120/208/240/277 volt ballast. Use a medium base, ED-17 lamp.
100MHEB
100 watt electronic metal halide ballast 120 thru 277 volt. Use medium base, ED-17 lamp.
50HPS
50 watt high pressure sodium 120/277 volt ballast. Use medium base, ED-17 lamp.
70HPS
70 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp.
100HPS
100 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp.
CF
Compact fluorescent electronic ballast 120 thru 277 volt. Use a GX24q base, 26, 32 or 42 watt lamp.
18LED-WW
18 light emitting diode array. (19 watt). Warm white (3500K). IES Type 1. 120 thru 277 volt.
27LED-WW
27 light emitting diode array. (29 watt). Warm white (3500K). IES Type 3. 120 thru 277 volt.
FL
36LED-WW
36 light emitting diode array. (37 watt). Warm white (3500K). IES Type 5. 120 thru 277 volt.
42" overall height x 5"/127mm dia, extruded fluted body
RD
18LED-BW
18 light emitting diode array. (19 watt). Bright white (5100K). IES Type 1. 120 thru 277 volt.
42" overall height x 5"/127mm dia, extruded smooth body
PM
Semi recessed pier mount
27LED-BW
27 light emitting diode array. (29 watt). Bright white (5100K). IES Type 3. 120 thru 277 volt.
36LED-BW
36 light emitting diode array. (37 watt). Bright white (5100K). IES Type 5. 120 thru 277 volt. All ballasts are factory wired for 277 volt, unless specified. Lamps not included (except LED options). All applicable ballasts are EISA compliant.
4
COLOR
All 13 standard and 5 premium AAL colors available. For RAL, please submit a 4-digit RAL number or color chip for custom colors.
5
MOUNTING
SPECIFICATIONS
PHOTOMETRY PROB
PROB
HOUSING The fixture housing and base are cast aluminum free of any porosity, foreign materials, or cosmetic fillers. The shaft shall be 5 in/127 mm wide and 23 in/584 mm tall, extruded 6061-T6 aluminum yielding a fixture height of 42 inches. The ballast is mounted internally and accessed by loosening three set screws and lifting the fixture head off the shaft. Relamping is done by loosening a captive screw on the side of the dome, directly opposite the hinge, and tilting the dome lid back. The lens is tempered glass, sealed to the housing with a silicone gasket. All internal and external hardware is stainless steel. The fixture is sealed to prevent dust, insect or moisture contamination by using one-piece, memory retentive, molded silicone gaskets. The fixture features tamper resistant hardware. ELECTRICAL The ballast is integral to the fixture, mounted on a prewired module with a quick disconnect plug. The ballast module has two keyhole slots and is removable by loosening two screws. All components and materials are U.L. recognized. Sockets are pulse rated porcelain. HID ballasts are high power factor, rated for -30°C starting. Medium base porcelain sockets are 4KV rated. Ballasts are wired at the factory for 277 volts, unless specified. Compact fluorescent transformers are electronic, 120 through 277 volt for 26, 32 or 42 watt 4 pin lamps.
FINISH Fixture finish shall consist of a five stage pretreatment regimen with a polymer primer sealer, oven dry off and top coated with a thermoset super TGIC polyester powder coat finish. The finish shall meet the AAMA 605.2 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance.
PROB-20MMC
0.1
CERTIFICATION The fixture is listed with ETL for outdoor, wet location use, UL1598 and Canadian CSA Std. C22.2 NO.250. IP Rating: 66 WARRANTY Fixture is warranted for three years. Ballast components carry the ballast manufacturer’s limited warranty. Any unauthorized return, repair, replacement or modification of the Product(s) shall void this warranty. This warranty applies only to the use of the Product(s) as intended by AAL and does not cover any misapplication or misuse of said Product(s), or installation in hazardous or corrosive environments. Contact AAL for complete warranty language, exceptions, and limitations.
The values below are in initial footcandles. Discount values to account for light losses due to voltage, temperature and atmospheric variations which affect light output. Mounting height is to the lamp center. All testing performed by a certified independent laboratory. Photometry is available in IES formatted files at www.aal.net.
.25 .5
.5
1.0
.25
1
.1
ARCHITECTURAL AREA LIGHTING PROB-20MMC CAST ALUMINUM BOLLARD WITH SPECULAR REFLECTOR AND CLEAR FLAT GLASS LENS ONE 20 WATT MINI BT-5 WITH PGJ5 BASE
PROB-39MHT6EB
Photometric Toolbox Professional Edition (c) copyright 1995-2008 by Lighting Analysts, Inc. Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers photometric file.
0.1
Page 1
CONVERSION TABLE .72 LLF, GRIDLINES = MTG. HT FIXTURE MTG. HT. (IN FEET) 3.5 WATTAGE 20MMC 1.00 39MMC 1.85
1.0 1
.25
AAL reserves the right to change product specifications without notice.
Horizontal Footcandles Scale: 1 Inch = 3.5 Ft. Light Loss Factor = 0.72 Total Lumens Per Luminaire = 1625 Mounting Height = 3.50 Ft Maximum Calculated Value = 4.35 Fc Arrangement: Single
.5
.5
.25
.1
REFLECTOR The reflector module shall be composed of a spun, specular aluminum panel rigidly attached to the die cast aluminum housing. The horizontal lamp reflectors shall meet ANSI-IES standards for full cutoff classification.
AAL CodeLink
SM
ARCHITECTURAL AREA LIGHTING PROB-39MH-T6EB CAST ALUMINUM BOLLARD WITH SPECULAR REFLECTOR AND CLEAR FLAT GLASS LENS ONE 39WATT CMH T6 WITH G12 BASE
PROB spec sheet
Photometric Toolbox Professional Edition (c) copyright 1995-2008 by Lighting Analysts, Inc. Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers photometric file.
Horizontal Footcandles Scale: 1 Inch = 3.5 Ft. Light Loss Factor = 0.72 Total Lumens Per Luminaire = 3400 Mounting Height = 3.50 Ft Maximum Calculated Value = 27.31 Fc Arrangement: Single
Page 1
1 PRSC-2 PRSC-3 PRSC-4 PRSC-W PRSC-X
2
LUMINAIRES Horizontal Type 2 Horizontal Type 3 Horizontal Type 4 Horizontal Column Accent/ Narrow Beam Horizontal LED, CF or IL
1D 2D
2DPB 2R
3
OUT PUT OPTIONS
Single source 100% primary output Up:down single source 94% primary with 6% secondary opposing output. Not for PRSC-W or LED. Up:down single source with pencil beam uplight. Not for PRSC-W or LED. Up:down dual source R111 as secondary opposing output. Available with 39MHT6EB-R111 ballast only.
LAMP/BALLAST
FOR PRSC-2 / PRSC-3 / PRSC-4 / PRSC-W 20 watt electronic metal halide 120/277 volt ballast. Use PGJ5 base, Mini MasterColor® lamp. 39MMC 39 watt electronic metal halide 120/277 volt ballast. Use PGJ5 base, Mini MasterColor® lamp. 39MHT6 39 watt magnetic metal halide 120/277 volt ballast. Use G12 base, T6 ceramic lamp. 39MHT6EB 39 watt electronic metal halide 120 thru 277 volt ballast. Use G12 base, T6 ceramic lamp. 39MHT6EB-R111 39 watt electronic metal halide 120 thru 277 volt ballast. For use with 2R option only. 50MH 50 watt metal halide 120/277 volt ballast. Use medium base, ED-17 lamp. 50MHEB 50 watt electronic metal halide 120 thru 277 volt ballast. Use medium base, ED-17 lamp. 70MH 70 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 70MHT6 70 watt metal halide 120/208/240/277 volt ballast. Use G12 base, T6 ceramic lamp. 100MH 100 watt metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 150PSMH Pulse start metal halide 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 150PSMHT6 Pulse start metal halide 120/277 volt ballast. Use G12 base, T6 ceramic lamp. 50HPS 50 watt high pressure sodium 120/277 volt ballast. Use medium base, ED-17 lamp. 70HPS 70 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 100HPS 100 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 150HPS 150 watt high pressure sodium 120/208/240/277 volt ballast. Use medium base, ED-17 lamp. 60CO 60 watt electronic ballast for Philips® Cosmo 200 thru 277 volt ballast. Use PGZ12 base cosmo lamp.
4
20MMC
AAL CodeLink
36LED-WW
SM
36LED-BW CF1
SCONCE PRSC spec sheet
CF2 IL55
ORDERING INFORMATION PRSC
FOR PRSC-X 36 light emitting diode array (37 watt). Warm white (3500K). 120 thru 277 volt. 36 light emitting diode array (37 watt). Bright white (5100K). 120 thru 277 volt. Horizontal Single CF, 120 thru 277 volt. GX24q base, 26, 32 or 42 watt lamp. Specify wattage. Horizontal Pair of CF, 120 thru 277 volt. GX24q base, 26, 32 or 42 watt lamp. Specify wattage. Horizontal 55 watt Induction system. 120, 208, 240 or 277 volt. -25°C min start temp. All ballasts are factory wired for 277 volts, unless specified. Lamps not included (except LED and IL options). All applicable ballasts are EISA compliant.
QRS
QL
SCB LDL BBU
347 SPC12 SPC27 BPC12 BPC27 TPC R24 R40
PFN DSB DSP
ORDERING EXAMPLE 1. LUMINAIRE 2. OUTPUT OPTIONS 3. LAMP/BALLAST
PRSC-3 1D 20MMC
4. OPTIONS
QRS
5. COLOR
BLK
OPTIONS
INTERNAL OPTIONS Restrike controller and T-4 mini-can socket will light following power outage until HID reaches full brightness. (Lamp wattage not to exceed ballast wattage). For horizontal reflector only. Not for LED. Socket for a T-4 mini-can halogen lamp. Must be field wired to a separate 120 volt circuit (Lamp wattage not to exceed ballast wattage). Not available for LED, CF1, CF2 or IL55 configuration. Surface Conduit Box. 1/2" NPT inlets on each side. Gasketed bottom cover for wire access. Standard finish is white. Lightly diffused glass lens to conceal the reflector and decrease visual brightness and glare. Battery backup powers the lamp for up to ninety minutes during a power failure. Output of the 32 watt lamp will be 575 lumens. Output from the 42 watt lamp will be 750 lumens. Operating temperature is 0°C to 55°C. For CF1 or CF2 configuration only. Integral. 120/240/347 volt ballast for HID lamp/ballast except the 50MH and 50HPS watt ballast.. Not available for 2R output. 120 volt swivel type photocell. Factory wired at 120 volt. Only available with 1D output (Photocell replaces finial) 208/240/277 volt swivel type photocell. Factory wired. Specify voltage. Only available with 1D output (Photocell replaces finial) Photocell Button Type 120V. Only available with 1D output (Photocell replaces finial). Photocell Button Type 208/240/277 volt. Only available with 1D output (Photocell replaces finial). Photocell Twist-Lok. Only available with 1D output (Photocell replaces finial). Photocell by others. Secondary source R111 Lamp with 24° Flood Pattern. Only available with 2R output. Secondary source R111 Lamp with 40° Flood Pattern. Only available with 2R output. DECORATIVE OPTIONS Cast aluminum finial painted brass color. Only available with 1D output. Dome spikes painted brass color. Dome spikes painted to match fixture color.
5
COLOR
All 13 standard and 5 premium AAL colors available. For RAL, please submit a 4-digit RAL number or color chip for custom colors.
SPECIFICATIONS
PHOTOMETRY PROB
PRSC
HOUSING The fixture housing is one-piece cast aluminum. The access door is cast aluminum, hinged and secured with two spring latches for relamping and internal access. The primary lens is molded tempered glass with a crowned shape to shed water. The single source bi-directional configuration uses a diffused lens to evenly illuminate the wall, and the dual source configuration uses a clear lens. The access door is sealed with a memory retentive, Rubatex, closed cell gasket. The rear electrical access has a molded silicone plug to completely seal the fixture from insects or dirt emanating from the electrical box or conduit. All internal and external hardware is stainless steel. OPTICAL ASSEMBLY The reflector module is composed of faceted, semi specular anodized aluminum panels rigidly attached in an aluminum module. The reflector module is easily removed from the ballast bracket by loosening four screws and lifting it out. The 2D uplight + downlight version includes a second reflector assembly attached to the ballast bracket which directs the light energy to the diffused lens used for the secondary light output. The 2R uplight + downlight version has a bracket assembly used to direct light from a R111 light source through the secondary clear lens. The reflectors shall meet ANSI-IES standards for full cut-off classification. ELECTRICAL The ballast is mounted on a prewired module with a quick disconnect plug and removed by loosening three captive quarter-turn fasteners. HID ballasts are high power factor, rated for -30°C starting. Sockets are medium base, pulse rated porcelain. Compact fluorescent sockets for a 26, 32, or 42 watt lamp are 4 pin, GX24q-4, with an electronic ballast, 0°F starting. Ballasts are prewired at the factory for 277 volts, unless specified.
finish. The finish shall meet the AAMA 605.2 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance. INSTALLATION To install the fixture, the die cast wall plate is secured to an octagonal j-box and wired to the power circuit. The fixture is plugged into a quick disconnect and then hooked onto the wall plate. Two captive screws are then tightened to secure the fixture to the wall plate. The fixture may be inverted if desired.
VERTICAL FOOTCANDLES ON THE WALL – MOUNTING HEIGHT 10 FEET.
HORIZONTAL FOOTCANDLES ON THE GROUND – MOUNTING HEIGHT 10 FEET. LLF=.8
PRSC-2-IL55
2 1
2
.5
10'/3.1 m mounting height
1 .5
.2
.2
CERTIFICATION The fixture is listed with ETL for outdoor, wet location use, in both an up and down orientation, UL1598 and Canadian CSA Std. C22.2 NO.250. IP Rating: 66 WARRANTY Fixture is warranted for three years. Ballast components carry the ballast manufacturer’s limited warranty. Any unauthorized return, repair, replacement or modification of the Product(s) shall void this warranty. This warranty applies only to the use of the Product(s) as intended by AAL and does not cover any misapplication or misuse of said Product(s), or installation in hazardous or corrosive environments. Contact AAL for complete warranty language, exceptions, and limitations.
0 1 2 (1 SQUARE GRID=10 FEET)
PRSC-4-60CO
2 1 10'/3.1 m mounting height
2
1 .5
AAL reserves the right to change product specifications without notice.
AAL CodeLink
3
.5 .2
.2 0
SM
1
2
3
0 1 2 (1 SQUARE GRID=10 FEET)
3
(1 SQUARE GRID=10 FEET)
PRSC-X-CF2-42
2
FINISH Fixture finish consists of a five stage pretreatment regimen with a polymer primer sealer, oven dry off and top coated with a thermoset super TGIC polyester powder coat
1
PRSC spec sheet
10'/3.1 m mounting height
2
1
.5 .2
.5 .2
®
Sustainability with
Style
PROV-TRA57
38
PROV-PR4-DB3
PROVIDENCE
®
FAMILY
39
®
Architectural Area Lighting 16555 East Gale Ave. | City of Industry | CA 91745 T 626.968.5666 | F 626.369.2695 | www.aal.net/aal/providence.html © 2011 Architectural Area Lighting | Design Patents Pending | Made in the USA | Rev Providence 1111
