X

X-CHIP-DRIVER-IR Descriptions: Congratulations with your purchase of this product. Read this manual carefully before using our Acclaim Lighting X-CHIP-DRIVER-IR. The X-CHIP-DRIVER-IR is a combination of a control interface and tension provider for our X-CHIP LED PCB modules as a LED fixture. A maximum of 24 channels can be controlled separately.

Delivery Packet: Check for transport damage. You should be in possession of the following items: 1 X-CHIP-DRIVER-IR 1 Manual 1 LED Remote(Infrared Remote Control) 1 IR EYE(sensor) 8 Flat cables for connection Should you discover transport damage after unpacking the equipment, inform the hauler immediately. Never connect a damaged device. You may also contact your supplier.

Main Features: 3A(50PCS of X-CHIP-PCB LED Module) capacity for each output(Total 8 ports in 400pcs). USITT Standard DMX-512(1990) multiplexed digital control. 1~10 patterns plus a sequence of 10 patterns, chase speed & fade time adjustable. Master/Slave function modes available. Fully controlled by DMX controller, XB-R1 or Infrared remote. Loading output modes consists of RGB mode, Color mode, Color &Brightness mode and Single mode. DMX Control Mode, Manual Mode and Auto Mode available. Different Output Group modes for user assignable . R.G.B color intensity can be adjustable separately. All work modes and parameters can be set by flipping 10-way Addressing Dip Switch and 8-way Function Dip Switch.

Technical Specifications: Power Requirement Connection

Housing Ingress Protection Rating Control Protocol Listing Operation temperature Dimensions Weights

12-24VDC, 24A Max. 8 output terminal sockets 2 power in and out terminal sockets 2 DMX in and out terminal sockets 1 IR connect socket PC +UV resistance IP20 DMX-512 (1990) CE certified -10 degC to +50 degC 195(L) x 110(W) x 22(H)mm 200g

*Please Note: Improvements and specifications in the design of the unit and the manual are subject to change without any prior written notice. *Special Note: For reducing signal errors and avoiding signal transmission problems and interference, it is always advisable to connect 120 ohm impedance DMX signal cable and DMX terminator for signal connection. Acclaim Lighting - Los Angeles, CA 90058 www.acclaimlighting.com

24-004-2042-00 Rev 2.2

Connecting the X-CHIP LED PCB modules to the X-CHIP-DRIVER-IR:

5-color rainbow Flat-cable

GND + G R B

GND + G R B

Out 1 Ext. IR Sensor

GND + G R B

Out 2

Power IN

Power Out

DC12V-24V

MAX 6.5A

GND + G R B

Out 3

Out 4

DMX Address

Mode

RS

ON

RS

ON

ON OFF V+

2

V+

1 2 3 4 5 6 7 8 9 10 Stand Alone 1

3 GND

1 GND 2 Data 3 Data +

DMX IN

1

4 GND

2 3 Red Fade

7

8 9 blue prog

10

DMX Control 1 2 3 4 5 6 7 8 9 10 001 002

X- C h i p - D r i v e r - I R

1 2 3 4 5 6 7 8 1

4 5 6 green speed

2 3 4 Group

5

6

XB-R1 Control DMX Control Manual Auto

511 512

7

8

5

6

7

8

RGB C&B Color Single

Out 5

Out 6

Out 7

Out 8

B R G + GND

B R G + GND

B R G + GND

B R G + GND

DMX Out

X-Chip-Driver-IR

Black White Red

DMX OUT

5-color rainbow Flat-cable

G D- D+

Mode

ON

1 2 3 4 5 6 7 8

DMX address setting

B R G 3 +24V GND

ON

B R G 4 +24V GND

1 2 3 4 5 6 7 8 9 10

DMX out XB-R1/DMX/Manual auto control RGB/C&B/Color /single Group

GND +24V G R B

Accessories:

8

GND +24V 7 G R B

Red

Cyan

Green

Magenta

Auto

Unit Setting Blue

Yellow

White

Amber

Brightness

Pattern Red

Speed Green

Fade Blue

X-CHIP Driver IR Power/Data supply

B R G 2 +24V GND

Power out

GND +24V 6 G R B

On/Off LED

GND

GND

+24V

+24V

Remote Controller

B R G 1 +24V GND

Power in

LED Remote

DMX in G D- D+

Black White Red

IR in

GND +24V 5 G R B

1.5mm

2

power cable

Power Supply 12-24VDC, 24A Max. IR EYE(Sensor)

LED REMOTE Cyan Auto

Fade Blue

Brightness

Magenta

Yellow

Red

Amber

Green

Blue Unit Setting

White

LED

Speed Green

Remote Controller

Pattern Red

On/Off

Or

IR EYE(Sensor) No. Of units / 24VDC,6.5A power supply MODEL

QTY.

MODEL

QTY.

X-CHIP-100 DIP

120

X-CHIP-W15 - Amber

120

X-CHIP-100 SMD

120

X-CHIP-W12 - 6000K

170

X-CHIP-300 DIP

120

X-CHIP-W12 - 3200K

170

X-CHIP-300 SMD

120

X-CHIP-W12 - Amber

170

X-CHIP-W15 - 6000K

120

X-CHIP-II

84

X-CHIP-W15 - 3200K

120

NOTE:

DMX Signal DMX Controller

Standard DMX cable

AC INPUT 100-240VAC

XB-R1 A Setup Tool

1.Providing the tension of 12-24VDC, 24A max can drive up to 50pcs X-CHIP PCB modules per port, the maximum of 400pcs per X-CHIP Driver IR in total. 2.Each PSU of 12-24VDC, 6.5A max can drive up 50pcs X-CHIP PCB modules per port, 120pcs per X-CHIP-DRIVER-IR in total.

-Page 2-

Operation Guide: 1. XB-R1 control(Programming) mode XB-R1 Control Mode enables. In this mode, the dip-switch 8 (8-way Function Dip Switch) is flipped to the "ON" position and the Output Load Mode is to be in the RGB output mode. A LED Setup Tool (depicted here) _XB-R1 is required to program the X-CHIP-DRIVER-IR. For further information, please refer to its accompanying manual.

A LED Setup Tool(XB-R1) (Sold separately)

1.1. Slave Control(DMX Mode) In Slave Control, the settings for the addresses(001-512) and the Glide Effect functions can be adjusted with a LED Setup Tool. There are 12 work modes for Slave Control.

MODE-1

RGB mode (24 channels in total=8x3 channels)

8 RGB mode: has 8 groups with RGB output, of which each group consists of 3 channels(24 channels in total). Channel 1-24 / Group 1-8

Color (R/G/B) Output 1

Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8

Red

Blue

MODE-2

1

4

7

10

13

16

19

22

2

5

8

11

14

17

20

23

3

6

9

12

15

18

21

24

Color and Brightness mode(16 channels in total=8x2 channels)

8 C&B mode: has 8 groups with color and intensity C&B output, of which each group consists of 2 channels (16 channels in total). Channel 1-16 / Group 1-8

C&B

MODE-3

Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8

Color

1

3

5

7

9

11

13

15

Brightness

2

4

6

8

10

12

14

16

Color mode(8 channels in total=8x1 channels)

8 COLOR mode: has 8 groups with Color control, of which each group consists of 1 channel (8 channels in total). The brightness is always 100% in this mode. Channel 1-8 / Group 1-8

C&B Color

Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8

1

2

4

3

6

5

7

8

Brightness 100% 100% 100% 100% 100% 100% 100% 100%

MODE-4

Patch mode RGB of 24 outputs---->12 outputs(4x3 channels)

4 RGB mode: in this mode, 2 outputs are patched. The driver has 6 identical outputs distributed over 4 groups. Channel 1-12 / Group 1-4

Color (R/G/B) Output 1-2

Output 3-4 Output 5-6 Output 7-8

Group 1 Group 2 Group 3 Group 4

Red

Blue

1

4

7

10

2

5

8

11

3

6

9

12

-Page 3-

MODE-5

Patch mode C&B of 16 outputs---->8 outputs(4x2 channels)

4 C&B mode: has 4 groups with C&B output, of which each group consists of 2 outputs that are controlled by 2 channels(8 channels in total). Channel 1-8 / Group 1-4

C&B

Output 1-2 Output 3-4 Output 5-6 Output 7-8

Group 1 Group 2 Group 3 Group 4

MODE-6

Color

1

3

5

7

Brightness

2

4

6

8

Patch mode Color of 8 outputs---->4 outputs(4x1 channels)

4 COLOR mode: has 4 groups with Color control, of which each group consists of 2 outputs that are controlled by 1 channel(4 channels in total). The brightness is always 100% in this mode. Channel 1-4 / Group 1-4

C&B

Output 1-2 Output 3-4 Output 5-6 Output 7-8

Group 1 Group 2 Group 3 Group 4

Color

1

2

3

4

Brightness 100% 100% 100% 100%

MODE-7

Patch mode RGB of 24 outputs---->6 outputs(2x3 channels)

2 RGB mode: in this mode, 4 outputs are patched. The driver has 12 identical outputs distributed over 2 groups. Channel 1-6

Color (R/G/B) Output 1-4 Red

Blue

MODE-8

Output 5-8

Group 1

Group 2

1

4

2

5

3

6

Patch mode C&B of 16 outputs---->4 outputs(2x2 channels)

2 C&B mode: has 2 groups with C&B output, of which each group consists of 4 outputs that are controlled by 2 channels (4 channels in total). Channel 1-4/Group1-2

C&B

MODE-9

Output 1-4

Output 5-8

Group 1

Group 2

Color

1

3

Brightness

2

4

Patch mode Color of 8 outputs---> 2 outputs(2x1 channel)

2 COLOR mode: has 2 groups with Color control, of which each group consists of 2 outputs that are controlled by 1 channel (2 channels in total). The brightness is always 100% in this mode. Channel 1-2/Group1-2

C&B

Output 1-4

Output 5-8

Group 1

Group 2

Color

1

2

Brightness

100%

100%

-Page 4-

MODE-10 Patch mode RGB of 24 outputs---->3 outputs(3x1 channels) 1 RGB mode: in this mode, 8 outputs are patched. The driver has 24 identical outputs distributed over 1 group. Color (R/G/B)

Channel 1-3 Group 1/ Output 1-8

Red

1 2

Blue

3

MODE-11 Patch mode C&B of 16 outputs---->2 outputs(2x1 channels) 1 C&B mode: has 1 group with C&B output, which consists of 8 outputs that are controlled by 2 channels. Channel 1-2

C&B

Group 1/ Output 1-8

Color

1

Brightness

2

MODE-12 Patch mode Color of 8 outputs---->1 outputs(1x1 channels) 1 COLOR mode: has 1 group with Color control, which consists of 1 output that is controlled by 1 channel. The brightness is always 100%. Channel 1 Group 1/ C&B Output 1-8

Color

1

Brightness

100%

NOTE: 1).The Glide Effect function can be switched on(YES) or off(NO). The transition from one level to another is smoother when this function is switched on. 2).When this function is switched off, the lighting intensity will changed from one level to another abruptly.(thus, when a quick lighting effect is required, the Guide Effect function should be switched off.) 3).If the DMX signal is interrupted, the driver will keep the last received DMX signal(information) until the driver is switched off or a new and valid DMX signal is sent. 4).When in link, the Slave will follow the Master, all parameter settings of each slave connected unit will be of no effect.

1.2.Master Control AUTO mode and MANUAL mode are for Master Control. Relevant functions are as below: (1) AUTO mode: Preset programs:1-10 programs and "AUTO" program ("AUTO"program is the sequential running of these1-10 programs.) Auto Speed: 1~100. (2) MANUAL mode:

Auto Fadetime: 0%~100%.

BLUE/Duration: 0%~100%.

RED/Speed: 0%~100%.

GREEN/Dimmer: 0%~100%.

NOTE: 1).The LEDs will turn red in Slave Control mode. The LEDs will give responding sensitive when the parameters are adjusted in Master Control. 2).If the LED is not selected in "Setup with answer", it will turn red. If the LED is not selected in :Setup no answer", it will switch off. When the user confirms the settings of the LED products, the LEDs will flash momentarily to confirm that the setting have been saved.

-Page 5-

2.DMX Control Mode(DMX Addressing) In this mode, the dip-switch 7 is flipped to the "ON" position 1 = ON the dip-switch 8(8-way function Dip Switch) is to the "OFF" (8-way Function Dip Switch) 1 2 3 4 5 6 7 8 position. And these switches sometimes used to activate a OFF 0= fixture special functions. DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication between intelligent fixtures. Each Dip Switch(10-way Addressing Dip Switch) represents a binary value. Dip Switch 1 address equals 1 (10-way Addressing Dip Switch) Dip Switch 2 address equals 2 START START SWITCHES ON SWITCHES ON Dip Switch 3 address equals 4 CH# CH# 1,2,4 1 1 11 Dip Switch 4 address equals 8 3,4 2 2 12 1,2 1,3,4 3 13 Dip Switch 5 address equals 16 2,3,4 3 4 14 Dip Switch 6 address equals 32 1,3 1,2,3,4 5 15 2,3 6 Dip Switch 7 address equals 64 7 1,2,3 8 4 Dip Switch 8 address equals 128 1,4 1,2,3,4,5,6,7,8,9 511 9 2,4 Dip Switch 9 address equals 256 10 Dip Switch 10 address equals 512 A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to achieve, for example: Setting DMX address for 21. Setting DMX address for 201. Flip switches1,3,&5 to the Flip switches1,4,7,& 8 to the "ON" position "ON" position 1=1 1=1 3=4 4=8 Dipswitches# 5=16 Value Dipswitches# 7=64 Value =21 8=128 =201 3.AUTO Control Mode 1 = ON

..

..

.. .. ..

0= OFF

.. .. ..

1 2 3 4 5 6 7 8 9 10

In this mode, the dip-switch 7 and 8(8-way function Dip Switch) are flipped to the "OFF" position, and the dip-switch 10(10-way Addressing Dip Switch) to the "ON" position. Flip the dip-switch 1~3(10-way Addressing Dip Switch) to select fade time, the dip-switch 4~6 (10-way Addressing Dip Switch)to select chase speed and the dip-switch 7~9 ( 10-Way Addressing Dip Switch) to select built-in 8 patterns. Their details can be referred to the below table; 1 = ON

8-way Function Dip Switch

1 = ON

1 2 3

0= OFF

0= OFF

000 100 010 110 001 101 011 111

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8 9 10

10-way Addressing Dip Switch

1 = ON

4 5 6

0%

0= OFF

000 100 010 110 001 101 011 111

14% 28% 43% 57% 71% 86% 100%

78 9

512S 180S 55S 16S 4.5S 1.3S 0.3S

000 100 010 110 001 101 011 111

1 2 3 4 5 6 7 8

"0" = "OFF" position "1" = "ON" position.

4.Manual Control Mode In this mode, the dip-switch 7 and 8(8-way Function Dip Switch) are flipped to the "OFF" position, and the dip-switch 10(10-way Addressing Dip Switch) to the "OFF" position. 1 = ON

10-way Addressing Dip Switch

8-way Function Dip Switch 1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8

0= OFF

4.1. RGB output mode enables, flip the dip-switch 1~3(10-way Addressing Dip Switch) to adjust Red color, the dip -switch 4~6(10-way Addressing Dip Switch) to adjust Green color, the dip-switch 7~9(10-way Addressing Dip Switch) to adjust Blue color. For more RGB color adjustment, please refer to the following table; 1 = ON

1 = ON

1 2 3

0= OFF

1 = ON

4 5 6

0= OFF

000 100 010 110 001 101 011 111

0% 14% 28% 43% 57% 71% 86% 100%

78 9

0= OFF

000 100 010 110 001 101 011 111

0% 14% 28% 43% 57% 71% 86% 100%

000 100 010 110 001 101 011 111

-Page 6-

0% 14% 28% 43% 57% 71% 86% 100%

"0" = "OFF" position "1" = "ON" position.

4.2. SINGLE output mode enables, flip the dip-switch 1~8(10-way Addressing Dip Switch)to set the intensity. The dip-switch 9 disable. Each dip-switch represents a binary value. Dip Switch 1 intensity equals 1 Dip Switch 2 intensity equals 2 Dip Switch 3 intensity equals 4 Dip Switch 4 intensity equals 8 Dip Switch 5 intensity equals 16 Dip Switch 6 intensity equals 32 Dip Switch 7 intensity equals 64 Dip Switch 8 intensity equals 128 The intensity can be set by combining the different dipswitches that will add up to the value you wish to achieve, for example: Example 1: Setting the intensity for 21. Example 2: Setting the intensity for 201. Flip switches1,3,&5 to the Flip switches1,4,7,& 8 to the "ON" position "ON" position 1=1 1=1 3=4 4=8 Dipswitches# 5=16 Value Dipswitches# 7=64 Value =21 8=128 =201

5.Output Group Mode Setting

In the function, the dip-switch 7(8-way Function Dip Switch) is flipped to the "ON" position and the dip-switch 8 to the "OFF" position. And use the dip-switch 1~4 of 8-way Function Dip Switch to set the desired Output Group Modes. 1 = ON

8-way Function Dip Switch 0= OFF

1 2 3 4 5 6 7 8

5.1. RGB output mode enables 5.1.1. 8 Group Output Mode is engaged by flipping the dip-switch 4 of 8-way Function Dip Switch to the "ON" position. In this mode, has 8 groups with RGB output, of which Output 1~8 is not perfectly identical. 5.1.2. 4 Group Output Mode is engaged by flipping the dip-switch 3 of 8-way Function Dip Switch to the "ON" position. In this mode, has 2 identical outputs distributed over 4 groups with RGB output. 5.1.3. 2 Group Output Mode is engaged by flipping the dip-switch 2 of 8-way Function Dip Switch to the "ON" position. In this mode, has 4 identical outputs distributed over 2 groups with RGB output. 5.1.4. 1 Group Output Mode is engaged by flipping the dip-switch 1 of 8-way Function Dip Switch to the "ON" or " OFF" position. In this mode, has 1 group with RGB output and Output 1~8 is identical.

5.2. SINGLE output mode enables 1 = ON

1 2 3 4

0= OFF

0000 1000 0100 1100 0010 1010 0110 1110 1111 0001

"0" = "OFF" position "1" = "ON" position. 1 Group Output 2 Group Output 3 Group Output 4 Group Output 6 Group Output 8 Group Output 12 Group Output 24 Group Output

5.2.1. In 1 Group Output mode, has 1 group with Single output and Output 1~24 is identical. 5.2.2. In 2 Group Output mode, has 12 identical outputs distributed over 2 groups with Single output. 5.2.3. In 3 Group Output mode, has 8 identical outputs distributed over 3 groups with Single output. 5.2.4. In 4 Group Output mode, has 6 identical outputs distributed over 4 groups with Single output. 5.2.5. In 6 Group Output mode, has 4 identical outputs distributed over 6 groups Single output. 5.2.6. In 8 Group Output mode, has 3 identical outputs distributed over 8 groups with Single output. 5.2.7. In 12 Group Output mode, has 2 identical outputs distributed over 12 groups with Single output. 5.2.8. In 24 Group Output mode, has 24 groups with Single output, of which Output1~24 is not identical.

-Page 7-

6.Output Load Mode Setting(Functions Setup) In the function, user can flip the dip-switch 5~6 of the 8-way Function Dip Switch to set the desired Output Load Modes. 1 = ON

5 6

"0" = "OFF" position "1" = "ON" position.

0= OFF

00 10 01 11

SINGLE COLOR C&B RGB

6.1.SINGLE output mode In the mode, the dip-switch 5,6 are flipped to the "OFF" position, and one output with Single is controlled by one channel. The output is set with Single output. 6.2.COLOR output mode In the mode, the dip-switch 5 is flipped to the "ON" position, and the dip-switch 6 to the "OFF" position, one output with Color control of RGB is controlled by one channel. The output is set with RGB output. 6.3.COLOR&BRIGHTNESS output mode In the mode, the dip-switch 5 is flipped to the "OFF" position, and the dip-switch 6 to the "ON" position, one output with Color & Intensity control is controlled by two channels. The output is set with RGB output. 6.4.RGB output mode In the mode, the dip-switch 5,6 are flipped to the "ON" position, one output with R.G.B. Control is controlled by three channels separately. And the Red effect is controlled by Channel1, the Green effect is controlled by Channel 2 and the Blue effect is controlled by Channel3. The Output Mode is set as the RGB mode.

7.LED Remote(Infrared Remote Control) Operation In this function, the dip-switch 8 is flipped to the "OFF" position, and all work modes and relative parameters can be set by operating the Infrared Remote. Before operation, the IR EYR(Sensor) should be connected properly. 7.1.Connecting the IR EYE(Sensor) to the X-CHIP-DRIVER-IR 7.1.1 Before connecting, please isolate the main power. 7.1.2 Plug the IR EYE(Sensor) into the Stereo Jack correctly. 7.1.3 Thus, turn the main power on.

Red

Cyan

Green

Magenta

Blue

Yellow

White

Amber

Brightness

Pattern Red

Speed Green

Fade Blue

Auto

Unit Setting

On/Off

Note: 1).Once you've confirmed all work modes and relative parameters, you can remove the IR EYE(Sensor). 2).NEVER remove the IR EYE(Sensor) when powering on for preventing from the damage.

LED Remote Controller

LED Remote

7.2.Operation Instructions 7.2.1 Before operation, make sure the batteries(3V, Cr2025) have been installed properly. 7.2.2 Operation Instructions There are 8 dedicated color brightness keys (marked Red, Green, Blue, White, Cyan, Magenta, Yellow, Amber) on the control interface. The On/Off, Auto, Unit setting, up and down keys-marked for "up" and for "down") are on the remote control as well.

Their detailed functions will be illustrated in the next table.

-Page 8-

Pushbuttons&Keys ON/OFF pushbutton RED pushbutton

Functions Power ON/OFF Red, 100% brightness

GREEN pushbutton

Green, 100% brightness

BLUE pushbutton

Blue, 100% brightness

CYAN pushbutton

Cyan, 100% brightness

MAGENTA pushbutton

Magenta, 100% brightness

YELLOW pushbutton

Yellow, 100% brightness

WHITE pushbutton

White, 100% brightness

AMBER pushbutton

Amber, 100% brightness

AUTO pushbutton

The color is changing automatically, and the brightness is 100%.

PATTERN/RED key

Select next pattern / increase red brightness. Holding the key down will gradually increase the brightness to its maximum value.

PATTERN/RED key

Select previous pattern / decrease red brightness. Holding the key down will gradually decrease the brightness to its minimum value.

SPEED/GREEN key

Increase speed/ increase green brightness. Holding the key down will gradually increase the brightness to its maximum value.

SPEED/GREEN key

Decrease speed / decrease green brightness. Holding the key down will gradually decrease the brightness to its minimum value.

FADE/BLUE key

Increase fadetime/ increase blue brightness. Holding the key down will gradually increase the brightness to its maximum value.

FADE/BLUE key

Decrease fadetime / decrease blue brightness. Holding the key down will gradually decrease the brightness to its minimum value.

BRIGHTNESS key

Increase master brightness. Holding the key down will gradually increase the brightness to its maximum value.

BRIGHTNESS key

Decrease master brightness. Holding the key down will gradually decrease the brightness to its minimum value.

UNIT SETTING pushbutton

Cancel the infrared remote operations. All settings will be done by flipping dip-switches.

NOTE: 1.The built-in patterns consists of 1~10 patterns plus a sequence of 10 patterns. 2.There are optional 10 different levels for chase speed; Speed Time

10 1S

9 2S

8 4S

7 8S

6 16S

5 32.5S

4 65S

3 130S

2 260S

1 512S

3.And fade time is available from 0% through 100%, total 11levels, 10% per level. 4.Effective distance from IR EYE(sensor) to LED Remote shall be limited within the range of 10m. Otherwise, it results out of control.

-Page 9-