SURF LIFE SAVING QUEENSLAND IRB EQUIPMENT SAFETY & COMPLIANCE INSPECTION FORMS
Surf Life Saving Queensland Version 1- April 2012
IRB EQUIPMENT SAFETY & COMPLIANCE INSPECTION FORMS The following is a brief description of each point on the form: Policy Statements pertaining to the specifications outlined in this document are available on the SLSA website. www.slsa.asn.au Gear and Equipment Specification (Lifesaving): June 2011
IRB/C1-1C General Arrangement Class 1-IRB Side Elevation and Section. IRB/C1-2C General Arrangement Class 1-IRB Plan. IRB/C2-1B General Arrangement Class 2-Rigid Hull IRB. IRB/C1-1C General Arrangement Class 3-IRB Side Elevation and Section. IRB/C1-2C General Arrangement Class 3-IRB Plan. IRB/C1-3B Stern Details. IRB/C1-4A Weatherproof Bags. IRB/C1-5C Detail of Re-righting Rope and Pouch. IRB/C1-6C Crew Hand Grips and Foot Straps. IRB/C1-7C Detail of Two Piece Hinged Floor. IRB/C1-9C Detail of Motor Safety Cable. IRB/C1-10B Detail of Reflective Tape Layout. IRB/C1-11A Detail of Optional “V” Planing Strake. IRB/C1-12A Detail of Mark .1. Motor Bracket Wearing Plate. IRB/C1-12.1 Detail of Mark .2. Motor Bracket Wearing Plate. IRB/C1-13A Permissible IRB Signage. IRB/C1-14 General Arrangement Paddle and Holders. IRB/C1-15A General Arrangement Rescue Tube Holder. IRB/C1-16B General Arrangement Tow Rope and Tow Rope Holder. IRB/C1-17A General Arrangement Foot Strap Locations. IRB/C1-18A Detail for Securing Fuel Cell to Floor.
Current endorsed manufactures for IRB items can be found on SLSA website under SLSA Approved Gear and Equipment List. NOTE: For inspections IRB are to be presented inflated with the floorboard out. The floorboard will be inspected for wear under the floorboard and the girder area of the IRB ie. Where the pontoon and floorboard meet.
Surf Life Saving Queensland Version 1- April 2012
How to complete the IRB Safety and Compliance Form A set on minimum compliance standards have been set and all Inflatable Rescue Boats within Surf Life Saving are to comply with these standards. There are a number of specifications that IRB manufactures must adhere to when manufacturing an IRB for Surf Life Saving Clubs or affiliated organisations. Inspection Officers are to provide a tick (
) or cross ( X ), next to each numbered item.
All non-compliant items are to be listed in the non-compliant section at the bottom of the page. An item/s that is not completely compliant and may need to be fixed/replaced is to be noted in the comments section and referring to the item number. Additional comments or information may also be added to reflect any non-compliance.
Definitions:
Inspection Officer- an officer appointed to inspect and ensure compliance
Compliant- Meets a minimum set standard to comply with manufactures specification and SLSA standards.
Non-Compliant- Item does not meet the minimum set standard to comply with manufactures and SLSA standards.
Surf Life Saving Queensland Page 3/5 Version 1- April 2012
IRB and Equipment Safety and Compliance Form *One (1) form per Inflatable Rescue Boat Date:
Club: Make:
Model:
IRB Class: Tick CLASS 1- SOFT HULL Manufacturer Serial Number:
CLASS 2- RIGID HULL
CLASS 3- CAT HULL HIN Number:
SLSA Approval Number:
Date Approved:
Marine Certificate of Operation Sighted:
YES
Serial Number Plates Affixed and in Good Condition:
Expiry Date:
NO YES
NO IRB Inspection Form Sighted:
YES
NO
Renewal Date Current:
YES
NO
State Marine Registration Number: Insert a TICK (
) if the IRB is COMPLIANT. Insert a CROSS (X) if the IRB is NON COMPLIANT
ITEM
PART A- IRB HULL AND FIXED FITTINGS
1 2
IRB Registration is Sign Written on the Location Relevant to Marine Safety Regulations for the State the IRB is Registered in Surf Rescue Sign Writting- Clear and Not Damaged
3
Solas Reflective Tape
4
Transom Construction: Fibreglass
5
Transom Saddle 5mm Plate
6
Motor Clamp Plate (5mm Lip)
7
All Bolts to have 1 thread only past Nyloc Nut
8
Towing Eye Bolts - 2
Marine ply
(Survey Compliant)
9
Self Bailers- Above Floor
10
Self Bailers- Below Floor
11
Floor Board Hold Down Batten: Marine Ply Fibreglass
PART B- ANCILLARY ITEMS Operational Accessory Bag (if Fitted) Operational Weatherproof Tool Bag (if fitted) Motor Safety Cable Knife with a Rounded Tip 6mm Knife Sheath Whistle Pea-less type and stowage at the Drivers Grab/Boarding Handle and a min of 20cm in length Rescue Tube Paddles – 2 Tow Rope – 15m in Length V Strips- No Crack or Damage Floor Sail and Trim- No Crack or Damage Full Cell - No Crack or Damage Fuel Line / Bulb / Fittings / Clamps (Covered) Full Cell has Safety Flaps and covers all Fuel Cell Fittings PART C- FLOOR BOARD AND FIXINGS
43 44 45 46
Main Floor Board- No Crack or Damage Bow Section Floor Board- No Crack or Damage Floor Board Hinge- No Crack or Damage Fuel Cell Fixings – 4
47 48 49 50 51
Fuel Cell Fixing Clips (70mm if Fitted) Crew Adjustable Foot Strap and Fixings Drivers Adjustable Foot Strap and Fixings Foot Straps Secured with Stainless Steel Screws, Washers, T Nuts, Plastic Batons No Unsealed Holes
52
No Sharp Edges or Protrusions
53
Protective Floor Covering EVA 165/195 kg/C3 13mm Thick
54
Protective Floor Covering (Serial Number)
55
Protective Floor Covering Condition
OR
X
COMMENTS
OR
X
COMMENTS
56 Serial Number of Floorboard Engraved on the Floorboard NOTE: The serial number for the floorboard is to be the same as the IRB serial number as originally SLSA approved. The floorboard serial number must be engraved on the top right hand side at the rear of the floor board. Additional Comments:
Non-Compliant Action Required: (note all ‘Do Not Use Tag’ numbers)
Office Use Only Inspector/s Name: Inspector/s Signature: Date:
Surf Life Saving Queensland Page 5/5 Version 1- April 2012
IRB Motor, Propeller and Propeller Guard Safety and Compliance Form Club:
Date:
SLSA Approval Number:
Date Approved:
Marine Certificate of Operation Sighted: NO
YES
Expiry Date:
Serial Number Plates Affixed and in Good Condition: NO
YES
IRB Inspection Form Sighted:
Insert a TICK ( ITEM 1
3 4
PART D- IRB MOTOR
Motor is Sealed
Motor Sealed All Seals Fitted and in Good Condition
6
No Obvious Motor Modifications
7
Rust/Corrosion Free
8
10
Tilt-Lock Removed or Disabled Mechanism to Prevent Motor from Starting in Gear Removed. Hoses and Wiring- No Crack or Damage
11
No Loose or Missing Bolts
12
Fuel Filter Clean (if applicable)
13
15
Choke/Primer Functions Smooth/Full-Throttle Action (in gear engine not running) of the Tiller Arm Motor Cover- No Cracks or Damage
16
Motor Clip
17
Clamp Threads and Handles (Spindles)
18
Clamp Brackets
19
Tilt Bracket & Fixings
20
Swivel Bracket & Fixings
21
Starter Handle
22
Motor Actually Runs & Idles
23
Gear Shift (F,R,N)
24
Restrictor Plate present
25
Transon Bracket- No Crack or Damage
26
Tilt Tension Nut
27
Tilt Pin
28
Water Intake
29
Starter Pawl
30
Fly Wheel- No Cracks or Damage
31
Spark Plugs & Lead
14
Motor 1 Yamaha Tohatsu Mercury Yes No
Motor 2 Yamaha Tohatsu Mercury Yes No
Motor 3 Yamaha Tohatsu Mercury Yes No
Motor 4 Yamaha Tohatsu Mercury Yes No
Motor 5 Yamaha Tohatsu Mercury Yes No
Motor Numbered
5
9
NO
) if the IRB is COMPLIANT. Insert a CROSS (X) if the IRB is NON COMPLIANT
Motor Type 2
YES
Yes No
Yes No
Surf Life Saving Queensland Page 6/5 Version 1- April 2012
Yes No
Yes No
Yes No
ITEM 32 33 ITEM 34 35 36 37 38 39 40 41
42 43
44
PART D- IRB MOTOR (cont) Tell Tale Fuel Connection- No Cracks or Damage PART E- PROPELLER & PROPELLER GUARD Propeller Guard Manufactures Serial No. (insert) Propeller Guard is Stainless Steel Non-Hydrofoiled Propeller Guard Securely Fixed Free of Rust/Corrosion Veins are in Good Condition No Sharp Edges Propeller does not exceed Prop Guard or Make Contact with the Side of the Prop Guard Stainless Steel 4 Blade Propeller Propeller Manufactures Serial No. (insert)
Motor 1
Motor2
Motor 3
Motor 4
Motor 5
Motor 1
Motor 2
Motor 3
Motor 4
Motor 5
Washers and Split Pins Present
Additional Comments:
Non-Compliant Action Required: (note all ‘Do Not Use Tag’ numbers)
Office Use Only Inspector/s Name: Inspector/s Signature: Date:
Surf Life Saving Queensland Page 7/5 Version 1- April 2012
IRB Room Compliance Form Club:
Date: Insert a TICK (
) if the IRB Room is COMPLIANT. Insert a CROSS (X) if the IRB Room is NON COMPLIANT
ITEM
PART F- IRB ROOM
1
Minimum of 1 Certified Class 3 Fuel Storage Room or Cabinet Minimum of 3 IRB Mixed Fuel Drums Minimum of 1 Fuel Funnel or Giggler Hose
2 3 4 5 6 7 8 9
OR
1 x Fuel/Oil Spill Kit Parts Additional Fuel Cells Stored in a Suitable location and Accessible System Minimum of 1 Fire Extinguisher 4.5kg Dry Powder, Mounted, Labelled and Currency Tested Retractable Water Hose with Auto Shut of Nozzle Retractable Air Hose with Inflation Device
11
2 x Pressure Gauges (1 Spare) Inflation Valve Adaptors to Inflate and Check Air Pressure for Your Particular Model IRBs Minimum of 1 Motor Trolley
12
1 x Rack or Trolley to Store IRB Motors
13
Motor Allocation/ Information Sign
14
Work Bench Basic Tool Kit Minimum of the Following Items: 1 x Spark Plug Socket 1 x Flat Blade Screwdriver 1 x Phillips Head Screwdriver 1 x 32mm Open End / Ring Spanner for Tilt Bolt Tension 1 x 3/8 Socket Set 1 x Pair Pliers 1 x Pair Multi Grip Pliers 1 x Open End/ Ring Spanner Set 1 x Hammer 1 x Hacksaw 1 x 100 mm Bench Vice Spare Parts Assortment Box
10
15
16
Test Tank or Flushing System to Run/Flush Motors
17
‘Do Not Use’ Tags x 5 PART G- IRB DISPLAYED OR IN A FOLDER Service History for IRB Motors Material Safety Data Sheets - Folder or Displayed Marine Registration Certificates- Displayed Service History for IRBs Copy of Motor Sealing Sheets for Each Motor Current Power Craft Code of Conduct Copy of IRB SLSA Approval Inspection Form for Each
ITEM 18 19 20 21 22 23 24
X
Surf Life Saving Queensland Page 8/5 Version 1- April 2012
COMMENTS
IRB 25 26
27 28 29
IRB Inflation Valve/Pressure Specification Information OH&S Information Sheet for: Fuel Storage Manual Handling Lifting Emergency Support Service Information Fuel Allocation and Mix Ratio IRB Rollover Procedure- Laminated
Additional Comments:
Non-Compliant Action Required: (note all ‘Do Not Use Tag’ numbers)
Office Use Only Inspector/s Name: Inspector/s Signature: Date:
Surf Life Saving Queensland Page 9/5 Version 1- April 2012