John Deere Spraying Solutions Spray Nozzles and Accessories Guide
Technozzlegy [tek-noz’-uhl-jee]
John Deere Spraying Solutions John Deere is redefining sprayer performance and accuracy. A concept so advanced, we’re calling it Technozzlegy, the next generation in a long line of John Deere nozzles, pumps and accessories. A total performance package that will unleash the full potential of your sprayer for every application-fertilizer, herbicides, fungicides and insecticides. It’s never been easier to choose the right spray nozzle to match each application. When you’re in the market for spray nozzles and accessories, you’ll find this booklet to be a helpful tool in determining the correct tip for your particular spraying situation. Your local John Deere dealer is also a valuable resource for any of your spraying application questions.
JOHN DEERE SPRAY PARTS Table of Contents Application type......................................................2 Spray Nozzle Information........................................6 Wear and Chemical Compatibility..........................10 Spray Heights........................................................12 Ultra Low-drift (ULA).............................................14 Ultra Plus Low-drift (ULAC)....................................16 TwinAir (TAQ)........................................................18 Low-drift Air (LDA).................................................20 GuardianTM (LDX)...................................................22 Low-drift (LD)........................................................24 Low-drift Ceramic (LDC)........................................26 Extended Range (ER).............................................28 Extended Range Stainless Steel (ERI).....................30 Extended Range Ceramic (ERC)..............................32 Flat Fan (FF)..........................................................34 High Flow (HF).......................................................36
Flood (FL)..............................................................38 Straight Stream Ceramic (STC)...............................40 Straight Stream (ST)..............................................42 Hollow Cone Ceramic (HCC)...................................44 Even Spray (ES)......................................................46 Chemical Resistant (CR).........................................48 Off-Center Brass (OC)............................................50 Fence Row/Boomless (XT).....................................52 TwinCapTM.............................................................54 Nozzle Body Adapters............................................55 Spray Nozzle Caps.................................................56 Plumbing products................................................58 Pumps...................................................................59 Application support...............................................60 Liquid-handling.....................................................61
1
JOHN DEERE SPRAY PARTS Application type Manufacturer's Recommended droplet size
Section
John Deere Spray Nozzle Selection Guide
Broadcast
The following chart has been designed to simplify selection of the correct spray tip type for the agrochemical to be applied. It is based on having good conditions for spraying and should be used in conjunction with the agrochemical manufacturer’s label.
2
Code ULA ULAC TAQ LDA LDX LD LDC ER ERC ERI FF
Spray Tip Ultra Low-drift Ultra Plus Low-drift ceramic TwinAir Low-drift Air Guardian™ Low-drift Low-drift Ceramic Extended Range Extended Range Ceramic Extended Range Stainless Steel Flat Fan
Orifice Material Polyacetal Ceramic Polyacetal Polyacetal Polyacetal Polyacetal Ceramic Polyacetal Ceramic Stainless Steel Polyacetal
JOHN DEERE SPRAY PARTS Application type Color Code VF F M C VC XC
Classification Very Fine Fine Medium Coarse Very Coarse Extremely Coarse
* See product page for complete listing.
Pressure Range 15 to 115 30 to 100 30 to 115 15 to 115 15 to 115 15 to 70 30 to 70 15 to 70 20 to 70 15 to 70 30 to 60
Nominal Spray Angle 120 110 110 110 120 110 110 80,110 110 80 80,110
Pattern Tapered Fan Tapered Fan Twin Tapered Fan Tapered Fan Tapered Fan Tapered Fan Tapered Fan Tapered Fan Tapered Fan Tapered Fan Tapered Fan
VF
F
M
C
VC
XC
3
Special
Banding & Directed Stream Wide Section
JOHN DEERE SPRAY PARTS Application type
4
Code HF FL STC ST D-C D-C HCC ES OC
Spray Tip High-Flow Flood Straight Stream Ceramic Straight Stream Disc and Core Disc and Core Hollow Cone Ceramic Even Spray Off-Center
XT
Fence row/boomless
TC CR
TwinCap™ Chemical Resistant
Orifice Material Polyacetal Polyacetal Ceramic PVDF Polyacetal Polyacetal Ceramic Polyacetal Brass
Polyacetal or Stainless Steel Polyacetal or PVDF PVDF
JOHN DEERE SPRAY PARTS Application type S These nozzles produce streams to minimize atomization.
Pressure Range 20 to 80 15 to 60 15 to 60 15 to 150 10 to 150 10 to 150 40 to 350 30 to 60 30 to 60
Nominal Spray Angle 140 80 to 145 0 0 0 45 to 110 80 80 80
Pattern Wide-angle Tapered Fan Wide-angle Flood 6-stream Stream Stream Hollow Cone Hollow Cone Even Fan Off-center Tapered Fan
30 to 60
105
Ultra-wide Boomless Fan
---
--110
VF
F
M
C
VC
XC
S S S
Double Tip Holder Tapered Fan
5
JOHN DEERE SPRAY PARTS Spray nozzle information ASABE S572 Droplet Size Classification The American Society of Agricultural and Biological Engineers (ASABE) developed the ASABE S572 standard to measure and interpret spray quality from tips. Spray Quality*
Size of Droplets
Retention on Difficult to Wet Leaves
Used for
Drift Potential
Very Fine
Small
Excellent
Exceptions
High
Fine
Very Good
Good Cover
Medium
Good
Most Products
Coarse
Moderate
Systemic Herbicides
Very Coarse
Poor
Soil Herbicides
Very Poor
Liquid Fertilizer
Extremely Coarse
Large
*Always read the pesticide label to determine which spray quality is required.
6
Low
JOHN DEERE SPRAY PARTS Spray nozzle information The ASABE S572 standard uses six droplet classification categories, six of which are common for agriculture and horticulture: Very Fine ,
Fine ,
Medium ,
Coarse ,
Very Coarse
and Extremely Coarse .
Most agrochemical applications recommend a fine, medium, or coarse spray. Fine
sprays provide enhanced retention for directed spraying on the target including: • Foliar-acting weed control • Contact-acting fungicides and insecticides
Medium
sprays are the most widely used spray type. • Used by default by most applicators when spray quality is not defined by the label. • Systemic-acting fungicides, insecticides and herbicides
Coarse
sprays are used with systemic, residual, and soil-applied herbicides.
7
JOHN DEERE SPRAY PARTS Suggested minimum spray heights — Flat fan spray nozzles Classification category Very fine Fine Medium Coarse Very coarse Extremely coarse
Thresholds Symbol
Dv0.1
Dv0.5
Dv0.9
41.5 65.7 88.0 95.6 109.2 109.2
99.9 163.6 249.4 365.1 408.3 >408.3
170.8 350.1 495.2 683.5 842.6 >842.6
Droplet size classification is based on BCPC specification and in accordance with ASAE S-572 at date of printing 10/04. Classifications are subject to change. Measures made by MALVERN particle size 2600 and Oxford Visisizer.
Droplet sizes are expressed in microns. One micron equals .001 millimeters. Other than the effects of the specific material being sprayed, the four major factors affecting droplet size are: • Spray nozzle style — flat fan, floods, cones, discs, cores • Capacity — low flow produces smaller droplets; high flow produces larger droplets • Pressure — low pressure produces larger droplets; high pressure produces smaller droplets • Spray pattern type — eliptical (flat fan nozzle), band (banded/flood nozzle), conical (cone nozzle)
8
JOHN DEERE SPRAY PARTS
9
JOHN DEERE SPRAY PARTS Wear and Chemical Compatibility
Comparative Accelerated Wear Test
% Increase in Flow
Bras Stain PVDF Polya Cera
Time (Hours)
10
Brass 26% (worst) Stainless Steel 15% (fair) PVDF 12% (good) Polyacetal 8% (better) Ceramic 5% (best)
JOHN DEERE SPRAY PARTS Wear and Chemical Compatibility CERAMIC (C) — Highly resistant to abrasive and corrosive chemistry, and provides superior wear resistance in abrasive applications and high pressures. Nozzle orifices are made of pink sintered ceramic and reinforced by special oxides. POLYACETAL (P) — Provides good resistance to most chemicals and superior resistance to wear with most agricultural chemistry. Susceptible to strong mineral acids and a few organic solvents. Resistance to most alkalis is excellent. Organic solvents usually cause slight swelling without any other harmful effect. POLYVINLYIDENE FLUORIDE (PVDF) — Should be used with acid-based agricultural defoliation chemistry. Good resistance to wear. Resists many reagents and high temperatures (up to 300º F , 148º C). Susceptible to high temper-atures above water boiling (210º F , 98º C) in combination with concentrated sulfuric and nitric acids. Preferred in industrial spraying applications. STAINLESS STEEL (SS) — Good resistance to chemicals and average wear resistance. BRASS (B) — Average resistance to most chemistry and poor wear resistance. Susceptible to corrosion, especially with fertilizers.
11
JOHN DEERE SPRAY PARTS Spray Heights Suggested Minimum Broadcast Spray Heights (Flat Fan Spray Tips)
12
(ERI)
(ERI)
(ULA)
(ULA)
JOHN DEERE SPRAY PARTS Spray Heights Optimum Broadcast Spray Heights (Flat Fan Spray Tips)
(ERI) (ULA)
* Not Recommended ** 40” tip spacing is prone to off-target trespass under certain conditions that affect drift.
13
JOHN DEERE SPRAY PARTS Ultra Low-drift Air (ULA) Spray pattern: 120-deg. tapered flat fan Capacity: .15 to .80 US gal/min .57 to 3 l/min
ULTRA low drift — The ULA nozzle with dual air-eduction technology produces large air-filled droplets, optimizing drift control and target coverage. The wide 120-degree spray angle enables the boom height to be lowered to further reduce drift. The UL is ideal for use with pre-emergence and broad-spectrum systemic products. Unlike other air-aspirated nozzles, the UL is precision molded completely out of polyacetal. Independent tests show that polyacetal wears up to two times longer than stainless steel, providing superior wear resistance. The UL’s small, compact size reduces the chance for breakage.
14
• • • • • •
Creates air-filled droplets which significantly reduces spray drift Wide 120° spray angle enables boom height to be lowered to further decrease drift Engineered for superior spray uniformity at all pressures Ideal use with pre-emergence and broad spectrum products Precision-molded in tough and durable polyacetal Small, compact size reduces the chances to of accidental breakage
JOHN DEERE SPRAY PARTS Ultra Low-drift Air (ULA) ULA 120 deg. — ASABE droplet classification data
gpm @ 40 psi
15 psi
20 30 40 psi psi psi
50 60 psi psi
0.15 0.20 0.25 0.30 0.40 0.50 0.60 0.80
VC VC VC VC VC XC XC XC
C VC VC VC VC XC XC XC
C C C C C VC VC VC
C C C VC VC VC XC XC
C C C C C VC VC VC
M C C C C C VC VC
70 80 90 100 115 psi psi psi psi psi M M M C C C C C
M M M M M C C C
M M M M M C C C
F M M M M M C C
F F M M M M M M
Quick-Change
Nozzles
10 pack
10 pack
PSULAQ20015 PSULAQ2002 PSULAQ20025 PSULAQ2003 PSULAQ2004 PSULAQ2005 PSULAQ2006 PSULAQ2008
PSULA20015 PSULA2002 PSULA20025 PSULA2003 PSULA2004 PSULA2005 PSULA2006 PSULA2008
15
JOHN DEERE SPRAY PARTS Ultra Plus Low-drift Air (ULAC)
Spray pattern: 110 deg.-tapered flat fan Capacity: .10 to 1.0 US gal./min. .4 to 3.7 l/min
ULTRA-Plus low drift ceramic — The ULAC air-aspirated spray nozzle produces large air-filled droplets that burst on impact, providing optimum drift-control capability and good target coverage. Its special two-part construction includes a removable pre-orifice, which makes cleaning easy. The ceramic nozzle and pre-orifice provide a long wear life, up to three times longer than stainless steel. • • •
16
Produces large air-filled droplets that burst on impact Provides optimum drift control capability and good target coverage Wear-resistant ceramic orifice
JOHN DEERE SPRAY PARTS Ultra Plus Low-drift Air (ULAC) "GPM @ 40 PSI"
ULAC 110 deg. - ASABE droplet classification chart 30 PSI
40 PSI
50 PSI
60 PSI
0.10
VC
VC
VC
VC
0.15
VC
VC
VC
VC
0.20
VC
VC
VC
VC
0.25
XC
VC
VC
VC
0.30
XC
XC
XC
0.40
XC
XC
0.50
XC
XC
0.60
XC
0.80
XC
1.00
XC
70 PSI
QuickChange
Nozzles
10 pack
10 Pack
80 PSI
90 PSI
100 PSI
C
C
C
C
PSULACQ1001
PSULAC1001
VC
VC
C
C
PSULACQ10015
PSULAC10015
VC
VC
VC
C
PSULACQ1002
PSULAC1002
VC
VC
VC
VC
PSULACQ10025
PSULAC10025
VC
VC
VC
VC
VC
PSULACQ1003
PSULAC1003
XC
VC
VC
VC
VC
VC
PSULACQ1004
PSULAC1004
XC
XC
VC
VC
VC
VC
PSULACQ1005
PSULAC1005
XC
XC
XC
VC
VC
VC
VC
PSULACQ1006
PSULAC1006
XC
XC
XC
XC
XC
XC
XC
PSULACQ1008
PSULAC1008
XC
XC
XC
XC
XC
XC
XC
PSULACQ1010
PSULAC1010
17
JOHN DEERE SPRAY PARTS Twin Air (TAQ)
Spray pattern: 110 deg.-tapered flat fan Capacity: .2 to 0.80 US gal./min. .75 to 3.0 l/min Twin Air — Twin Air spray nozzles are the best choice for high coverage applications where on target spray delivery is important. They are ideal for low crops with complex canopies, such as vegetables, where through coverage of the target and protection of the surroundings are of high importance. • • • • •
18
Forward and rear facing fans Uniform coverage and reduced drift Easy to install, patent pending locking ring and o-ring seal Integrated strainers are matched to the nozzle size to prevent overstraining or plugging Compact, break-resistant design fits on most common nozzle bodies
JOHN DEERE SPRAY PARTS Twin Air (TAQ) GPM @ 40 PSI
TAQ 110-deg - ASABE droplet classification chart
Quick Change
30 psi
40 psi
50 psi
60 psi
70 psi
80 psi
90 psi
100 psi
115 psi
10 pack
0.20
C
M
M
M
M
M
M
F
F
PSTAQ1002
0.25
VC
C
M
M
M
M
M
M
M
PSTAQ10025
0.30
VC
C
M
M
M
M
M
M
M
PSTAQ1003
0.40
C
M
M
M
M
M
M
M
M
PSTAQ1004
0.50
VC
C
M
M
M
M
M
M
M
PSTAQ1005
0.60
VC
C
M
M
M
M
M
M
M
PSTAQ1006
0.80
VC
VC
C
C
M
M
M
M
M
PSTAQ1008
19
JOHN DEERE SPRAY PARTS Low-drift Air (LDA) Spray pattern: 110 deg.-tapered flat fan Capacity: .15 to .50 US gal./min. .57 to 1.89 l/min Low-drift air — LDA spray nozzles are patented air-educted nozzles specially designed toward achieving superior results. • • • • •
20
Produces air-induced sprays for reduced drift and environmental impact while increasing droplet deposition and retention on the foliage Provides better coverage with more drops per US gallon Optimized for the productivity of the most common application rates Delivers faster work rates with better drift reduction, allowing for more productive spray days Each nozzle is clearly marked with an arrow indicating the direction of travel
JOHN DEERE SPRAY PARTS Low-drift Air (LDA) gpm @ 40 PSI
LDA 110 deg- ASABE droplet classification data
Quick-Change
Nozzle
15 20 30 40 50 60 70 80 90 100 115 PSI PSI PSI PSI PSI PSI PSI PSI PSI PSI PSI
10 pack
10 pack
0.15
XC
XC
VC
C
C
C
M
M
M
M
M
PSLDAQ10015
PSLDA10015
0.20
XC
XC
VC
C
C
C
M
M
M
M
M
PSLDAQ1002
PSLDA1002
0.25
XC
XC
VC
C
C
C
C
C
M
M
M
PSLDAQ10025
PSLDA10025
0.30
XC
XC
VC
C
C
C
C
C
M
M
M
PSLDAQ1003
PSLDA1003
0.35
XC
XC
VC
C
C
C
C
C
M
M
M
PSLDAQ10035
PSLDA10035
0.40
XC
XC
VC
C
C
C
C
C
M
M
M
PSLDAQ1004
PSLDA1004
0.50
XC
XC
VC
C
C
C
C
C
M
M
M
PSLDAQ1005
PSLDA1005
21
JOHN DEERE SPRAY PARTS Guardian TM (LDX)
Spray pattern: 120-deg. wide-angle Capacity: .10 to .80 US gal./min. .4 to 3 l/min. Guardian LDX — Designed to create a more-consistent droplet size, the new Guardian LDX quickchange nozzle reduces the amount of “driftable fines” across a wide variety of pressure settings. The one-piece design includes nozzle, cap, gasket, and strainer for easier handling. Its 120-degree angled pattern lets you spray closer to the target, reducing drift, while improving uniformity. A unique 20-degree incline increases application versatility to control diseases, insects, and weeds. And a bold arrow on the spray nozzle indicates incline direction for easy installation, and allows you to adjust your application to match the target. To aim the spray, simply aim the arrow. • • •
22
• •
Applications of insecticide and fungicide Delivers a more consistent droplet and spray pattern, making it versatile for more rates and speeds Quick-change nozzle design eliminates loose nozzles, caps, gaskets and strainers for easier installation and safer handling Wide 120° pattern is inclined 20° to enhance application versatility A bold arrow clearly indicates incline direction for easy installation
JOHN DEERE SPRAY PARTS Guardian TM (LDX) GPM @ 40 PSI
LDX 120 deg.- ASABE droplet classification chart
QuickChange
15 PSI
20 PSI
30 PSI
40 PSI
50 PSI
60 PSI
70 PSI
80 PSI
90 PSI
100 PSI
115 PSI
10 pack
0.10
C
C
C
M
M
M
M
M
M
M
M
PSLDXQ2001
0.15
C
C
C
M
M
M
M
M
M
M
M
PSLDXQ20015
0.20
VC
C
C
C
C
M
M
M
M
M
M
PSLDXQ2002
0.25
VC
C
C
C
C
M
M
M
M
M
M
PSLDXQ20025
0.30
VC
C
C
C
C
C
M
M
M
M
M
PSLDXQ2003
0.40
VC
C
C
C
C
C
M
M
M
M
M
PSLDXQ2004
0.50
VC
C
C
C
C
C
M
M
M
M
M
PSLDXQ2005
0.60
XC
VC
C
C
C
C
M
M
M
M
M
PSLDXQ2006
0.80
XC
XC
VC
C
C
C
M
M
M
M
M
PSLDXQ2008
23
JOHN DEERE SPRAY PARTS Low-drift (LD)
Spray pattern: 110-deg. tapered flat fan Capacity: .15 to .80 US gal./min. .57 to 3 l/min.
Low-drift poly — The drift-reducing LD nozzle produces fewer fine droplets than a standard flat fan and, with its dual air-education technology, produces large air-filled droplets, optimizing drift control and target coverage. Because of its drift-reducing flat spray, it allows operations in a wider weather window. Unlike other drift-reducing nozzles, the flow from the LD is a straight route through the nozzle, which decreases the chance for clogging. Made from polyacetal, the LD nozzle provides superior wear resistance, up to twice as long as stainless steel.
24
• • • • •
Applications of pre-emergent herbicides and post-emergent herbicides Significantly reduces spray drift, widening the operational window Dual air-eduction technology produces large air-filled droplets Removable pre-orifice makes for easy cleaning Precision-molded in tough and durable polyacetal
0.40 0.50 0.60 0.80
C VC VC XC
C C C M M C C C C C JOHN DEERE SPRAY PARTS VC VC C C C Low-drift (LD) VC VC VC C C
gpm LD 110 deg. — ASABE droplet classification data @ 15 20 30 40 50 60 70 40 psi psi psi psi psi psi psi psi 0.15 M M M M M M F 0.20 C C M M M M M 0.25 C C M M M M M 0.30 C C C M M M M 0.40 C C C M M M M 0.50 VC C C C C M M 0.60 C VC C C C C C 0.80 VC VC C C C C C
Nozzle 10 pack PSLD10015 PSLD1002 PSLD10025 PSLD1003 PSLD1004 PSLD1005 PSLD1006 PSLD1008
25
JOHN DEERE SPRAY PARTS Low-drift Ceramic (LDC) Spray pattern: 110-deg. tapered flat fan Capacity: .1 to .40 US gal./min. .4 to 1.5 l/min.
Low-drift Ceramic — The drift-reducing LDC nozzle produces fewer fine droplets than a standard flat fan and, with its dual air-eduction technology, produces large air-filled droplets, optimizing drift control and target coverage. Unlike other drift-reducing nozzles, the flow from the LDC is a straight route through the nozzle, which decreases the chance for clogging. The ceramic nozzle and pre-orifice provide a long wear life, up to three times longer than stainless steel. • • • • 26
Droplet size balances drift reduction and target coverage Pre-orifice design creates droplets that are well suited for a wide range of applications Versatile and long-lasting tip Wear-resistant ceramic orifice
JOHN DEERE SPRAY PARTS Low-drift Ceramic (LDC) GPM @ 40 PSI
LDC 110 deg.- ASABE droplet classification data
Nozzles
30 PSI
40 PSI
50 PSI
60 PSI
70 PSI
0.10
M
M
F
F
F
PSLDC10010
10 pack
0.15
M
M
M
M
M
PSLDC10015
0.20
M
M
M
M
M
PSLDC1002
0.30
C
M
M
M
M
PSLDC1003
0.40
VC
C
C
C
M
PSLDC1004
27
JOHN DEERE SPRAY PARTS Extended Range (ER)
Spray pattern: 80- or 110-deg. tapered flat fan Capacity: 80-deg: .15 to .60 US gal./min .57 to 2.27 l/min. 110-deg: .15 to 1.5 US gal./min. .57 to 6 l/min. Extended Range — The ER tip provides a consistent pattern and coverage over a wide range of operating pressures — down to 15 psi — making it ideal for use with automatic rate controllers. It delivers a versatile spray pattern for applications of herbicides, fungicides, insecticides, and growth regulations. Molded completely out of polyacetal, the ER tip provides up to two times longer wear resistance to most agricultural chemicals compared to a stainless-steel insert. • • • • 28
Applications of herbicides, fungicides, insecticides and growth regulations Excellent spray distribution over a wide range of operating pressures Precision-molded in tough and durable polyacteal Provides up to two times longer wear resistance to most agricultural chemicals compared to a stainless-steel insert
JOHN DEERE SPRAY PARTS Extended Range (ER) GPM @ 40 PSI
15 PSI M M M C C C
ER 80 deg.- ASABE droplet classification chart 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI M F F F F M F F F F M M F F F M M M M F C M M M M C C C M M
70 PSI F F F F F M
Quick Change 10 Pack PSERQ80015 PSERQ8002 PSERQ8003 PSERQ8004 PSERQ8005 PSERQ8006
Nozzles 10 pack PSER80015 PSER8002 PSER8003 PSER8004 PSER8005 PSER8006
0.15 0.20 0.25
15 PSI M M M
ER 110 deg.- ASABE droplet classification chart 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI F F F F F M F F F F M F F F F
70 PSI F F F
Quick Change 10 Pack PSERQ10015 PSERQ1002 PSERQ10025
Nozzles 10 pack PSER10015 PSER1002 PSER10025
0.30 0.40 0.50 0.60 0.80 1.00 1.50
M C C C VC VC VC
PSERQ1003 PSERQ1004 PSERQ1005 PSERQ1006 PSERQ1008 PSERQ1010 PSERQ1015
PSER1003 PSER1004 PSER1005 PSER1006 PSER1008 PSER1010 PSER1015
0.15 0.20 0.30 0.40 0.50 0.60 GPM @ 40 PSI
M M C C C C VC
M M M C C C VC
F M M M M M C
F M M M M M C
F F M M M M M
F F F M M M M
29
JOHN DEERE SPRAY PARTS Extended Range Stainless Steel (ERI)
Spray pattern: 80-deg. tapered flat fan Capacity: .1 to 1.5 US gal./min. .4 to 6 l/min.
Extended Range Stainless Steel — The ERI nozzle provides a consistent pattern and coverage over a wide range of operating pressures — down to 15 psi — making it ideal for use with automatic rate controllers. It delivers a versatile spray pattern for applications of herbicides, fungicides, insecticides, and growth regulations. • • • •
30
Applications of herbicides, fungicides, insecticides and growth regulations Adjustable droplet size according to pressure Manages drift when used at a low pressure and gives excellent coverage at higher pressures Insert is precision machined stainless steel
JOHN DEERE SPRAY PARTS Extended Range Stainless Steel (ERI) GPM @ 40 PSI
ERI 80 deg.- ASABE droplet classification chart
Quick Change
Nozzles
15 PSI
20 PSI
30 PSI
40 PSI
50 PSI
60 PSI
70 PSI
10 Pack
10 pack
0.10
M
F
F
VF
VF
VF
VF
PSERIQ8001
PSERI8001
0.15
M
F
F
F
F
VF
VF
PSERIQ80015
PSERI80015
0.20
M
M
F
F
F
F
VF
PSERIQ8002
PSERI8002
0.30
C
M
M
F
F
F
F
PSERIQ8003
PSERI8003
0.40
C
C
M
M
M
F
F
PSERIQ8004
PSERI8004
0.50
C
C
C
M
M
M
F
PSERIQ8005
PSERI8005
0.60
C
C
C
M
M
M
M
PSERIQ8006
PSERI8006
0.80
VC
C
C
C
C
M
M
PSERIQ8008
PSERI8008
1.00
VC
VC
VC
C
C
C
M
PSERSQ8010
PSERS8010
1.50
XC
VC
VC
C
C
C
C
PSERSQ8015
PSERS8015
31
JOHN DEERE SPRAY PARTS Extended Range Ceramic (ERC)
Spray pattern: 110-deg. Tapered flat fan Capacity: .15 to .60 US gal./min. .57 to 2.27 I/min.
Extended Range Ceramic — The ERC nozzle provides a consistent pattern and coverage over a wide range of operating pressures — down to 15 psi — making it ideal for use with automatic rate controllers. It delivers a versatile spray pattern for applications of herbicides, fungicides, insecticides, and growth regulations. The ceramic nozzle provides a long wear life. • • • •
32
Applications of herbicides, fungicides, insecticides and growth regulations Droplet size suited for target coverage Wear-resistant ceramic orifice Wide range of operating pressures
JOHN DEERE SPRAY PARTS Extended Range Ceramic (ERC) GPM @ 40 PSI 0.15
ERC 110 deg.- ASABE droplet classification chart
Quick Change
Nozzles
20 PSI
30 PSI
40 PSI
50 PSI
60 PSI
70 PSI
10 Pack
F
F
F
F
F
VF
PSERCQ10015
PSERC10015
10 pack
0.20
F
F
F
F
F
F
PSERCQ1002
PSERC1002
0.30
M
M
M
F
F
F
PSERCQ1003
PSERC1003
0.40
M
M
M
M
M
F
PSERCQ1004
PSERC1004
0.50
M
M
M
M
M
M
PSERCQ1005
PSERC1005
0.60
M
M
M
M
M
M
PSERCQ1006
PSERC1006
33
JOHN DEERE SPRAY PARTS Flat Fan (FF)
Spray pattern: 80- or 110-deg. tapered flat fan Capacity: 80-deg: .067 to 2.0 US gal./min .253 to 7.5 l/min. 110-deg: .1 to 2.0 US gal./min. .4 to 7.5 l/min. Flat Fan — The FF nozzle with its simple, one-piece design creates a flat sheet of spray and provides a consistent pattern over a range of pressures. The mixed droplet spectrum makes this product suited for applications of herbicides, fungicides, insecticides, and PGRs. It’s an economical option for moderate use. Made from polyacetal, the FF nozzle provides superior wear resistance. • • • •
34
Applications of herbicides, fungicides, insecticides, and PGRs Mixed droplet spectrum allows effective delivery and retention of agrochemicals Precision-molded in tough and durable polyacetal Superior wear resistance
gpm @ 40 psi 0.067 0.10 0.15 0.20 0.30 0.40 0.50 0.60 0.80 1.00 1.50 2.00 gpm @ 40 psi 0.10 0.15 0.20 0.30 0.40 0.50 0.60 0.80 1.00 1.50 2.00
FF 80 deg. — ASABE droplet classification data
Nozzle
30 psi
40 psi
50 psi
60 psi
10 pack
VF F M M C C C C C VC VC VC
VF F F M M M M C C C VC VC
VF F F F M M M M C C C VC
VF F F F F M M M C C C VC
PSFF800067 PSFF8001 PSFF80015 PSFF8002 PSFF8003 PSFF8004 PSFF8005 PSFF8006 PSFF8008 PSFF8010 PSFF8015 PSFF8020
FF 110 deg. — ASABE droplet classification data 30 psi F F F M M M M C C C C
40 psi F F F F M M M C C C C
50 psi F F F F M M M C C C C
JOHN DEERE SPRAY PARTS Flat Fan (FF)
Nozzle 60 psi F F F F F M M C C C C
10 pack PSFF1001 PSFF10015 PSFF1002 PSFF1003 PSFF1004 PSFF1005 PSFF1006 PSFF1008 PSFF1010 PSFF1015 PSFF1020
35
JOHN DEERE SPRAY PARTS High Flow (HF)
Spray pattern: 140-deg. wide-angle flood Capacity: .80 to 6.0 US gal./min. 3 to 22.7 l/min.
High Flow — The HF spray nozzle features a unique flat-fan spray design for excellent spray distribution and free flow for improved spray consistency. Low CV (Coefficient of Variation) performance ratings provide excellent distribution. The 140-degree angled spray pattern provides excellent distribution in wide-spaced setups (30, 40, 45, or 60 inch). Made from polyacetal, the high-flow spray nozzle provides superior wear resistance. • • • • 36
Straight-through design to reduce clogging Incredibly uniform application across the boom The 140° pattern allows lower spray heights to reduce the risk of drift during sensitive applications Superior wear resistance
JOHN DEERE SPRAY PARTS High Flow (HF) GPM @ 40 PSI
HF 140 deg.- ASABE droplet classification chart
QuickChange
20 PSI
30 PSI
40 PSI
50 PSI
60 PSI
70 PSI
80 PSI
10 pack
0.80
XC
XC
XC
XC
XC
XC
XC
PSHFQ4008
1.00
XC
XC
XC
XC
XC
XC
XC
PSHFQ4010
1.50
XC
XC
XC
XC
XC
XC
XC
PSHFQ4015
2.00
XC
XC
XC
XC
XC
XC
XC
PSHFQ4020
3.00
XC
XC
XC
XC
XC
XC
XC
PSHFQ4030
4.00
XC
XC
XC
XC
XC
XC
XC
PSHFQ4040
5.00
XC
XC
XC
XC
XC
XC
XC
PSHFQ4050
6.00
XC
XC
XC
XC
XC
XC
XC
PSHFQ4060
37
JOHN DEERE SPRAY PARTS Flood (FL)
Spray pattern: 105- to 145-deg. wide-angle flood Capacity: .2 to 2.0 US gal./min. .75 to 7.5 l/min. Polyacetal-molded for excellent life Flood— The FL nozzle produces large droplets in a wide, flat, 105- to 145-degree spray angle pattern suited for pre- and post-emergent herbicides. This flexible nozzle can be used in 20- to 60-inch nozzle spacing applications. Its large orifice produces coarser droplets, which are less prone to drift. The FL’s large, circular orifice reduces the chances of blocking. Made from polyacetal, the FL nozzle provides superior wear • • • •
38
Spray angle pattern suited for pre and post-emergent herbicides Large orifice produces coarser droplets which are less prone to drift Large circular orifice reduces the chances of blocking Precision-molded in tough and durable polyacetal
JOHN DEERE SPRAY PARTS Flood (FL) GPM @ 10 PSI
Spray Angle
FL-Flood.- ASABE droplet classification chart
Nozzles
10 PSI
20 PSI
30 PSI
40 PSI
50 PSI
60 PSI
0.20
105
C
C
M
M
M
M
PSFL2
0.25
110
C
C
M
M
M
M
PSFL025
0.30
110
C
C
M
M
M
M
PSFL3
0.40
120
C
C
M
M
M
M
PSFL4
0.50
125
C
C
C
M
M
M
PSFL5
0.75
145
C
C
C
C
C
C
PSFL75
1.00
160
VC
VC
C
C
C
C
PSFL10
1.50
145
XC
VC
VC
C
C
C
PSFL15
2.00
140
XC
VC
VC
VC
C
C
PSFL20
10 pack
39
JOHN DEERE SPRAY PARTS Straight Stream Ceramic (STC)
Spray pattern: six straight streams at 110-deg. Capacity: .15 to 1.5 US gal./min. .57 to 6 l/min
Straight Stream Ceramic — The STC nozzle is ideal for liquid fertilizer application. Its 110-degree spray angle provides accurate span distribution and target coverage, and its ceramic orifice provides maximum wear resistance and accurate, uniform distribution. This nozzle provides extremely coarse droplets, improving fertilizer distribution, and a minimized risk of leaf burn. • • • •
40
Six streams distribute fertilizer more evenly than on single pattern Provides extremely coarse droplets Reduced atomization limits leaf burn and scorching Wear-resistant ceramic orifice
JOHN DEERE SPRAY PARTS Straight Stream Ceramic (STC) GPM @ 40 PSI
STC-Straight Stream-ASABE dropplet classification chart
QuickChange
15 PSI
20 PSI
30 PSI
40 PSI
50 PSI
60 PSI
10 pack
0.15
XC
XC
XC
XC
XC
XC
PSSTCQ10015
0.20
XC
XC
XC
XC
XC
XC
PSSTCQ1002
0.25
XC
XC
XC
XC
XC
XC
PSSTCQ10025
0.30
XC
XC
XC
XC
XC
XC
PSSTCQ1003
0.40
XC
XC
XC
XC
XC
XC
PSSTCQ1004
0.50
XC
XC
XC
XC
XC
XC
PSSTCQ1005
0.60
XC
XC
XC
XC
XC
XC
PSSTCQ1006
0.80
XC
XC
XC
XC
XC
XC
PSSTCQ1008
1.00
XC
XC
XC
XC
XC
XC
PSSTCQ1010
1.50
XC
XC
XC
XC
XC
XC
PSSTCQ1015
41
JOHN DEERE SPRAY PARTS Straight Stream (ST)
Spray pattern: straight stream Capacity: 1.0 to 2.0 US gal./min. 3.7 to 7.5 l/min.
Straight Stream — 0-degree ST regulates flow, then produces a straight stream pattern. • • •
42
Provides a single jet of spray for streaming or injecting liquid fertilizer Precision molded using chemically-resistant PVDF Superior resistance to orifice wear
JOHN DEERE SPRAY PARTS Straight Stream (ST) GPM @ 40 PSI
ST- Straight stream .- ASABE droplet classification data
Nozzles
15 PSI
20 PSI
30 PSI
40 PSI
60 PSI
10 pack
1.0
XC
XC
XC
XC
XC
PSST10
1.5
XC
XC
XC
XC
XC
PSST15
2.0
XC
XC
XC
XC
XC
PSST20
43
JOHN DEERE SPRAY PARTS Hollow Cone Ceramic (HCC)
Spray pattern: 80-deg. hollow cone Capacity: .03 to .17 US gal./min. .11 to .64 l/min.
Hollow Cone Ceramic — The HCC nozzle produces a fine droplet in a hollow-cone, 80-degree pattern. Its special two-part construction includes a removable pre-orifice, which makes for easy cleaning. The ceramic nozzle and pre-orifice provide a long wear life. • • • •
44
Applications of insecticide and fungicide Produces finely atomized droplets in a hollow-cone, 80-degree pattern Special two-part construction includes removable pre-orifice, makes for easy cleaning Ceramic nozzle and pre-orifice provide a long wear life
.08 .10 .12 .18 gpm @ 15 psi .03 .04 .06 .12 .17
PMHC8 PMHC10 PMHC12 PMHC18
PM904-6 PM904-6 PM904-1 PM904-1
F F F F
F F F F
F F F F
F F F F
F F F F
VF VF VF VF F VF VF VF JOHN DEERE SPRAY PARTS F F VF VF Hollow Cone Ceramic (HCC) F F F VF
HCC 80-deg. — ASABE droplet classification data 40 psi VF VF VF F F
50 psi VF VF VF F F
60 psi VF VF VF F F
70 psi VF VF VF F F
80 psi VF VF VF VF F
90 psi VF VF VF VF F
100 psi VF VF VF VF VF
125 psi VF VF VF VF VF
150 psi VF VF VF VF VF
Quick-Change 350 psi VF VF VF VF VF
10 pack PSHCCQ3 PSHCCQ4 PSHCCQ6 PSHCCQ12 PSHCCQ17
45
JOHN DEERE SPRAY PARTS Even Spray (ES)
Spray pattern: 80-deg. tapered flat fan Capacity: .1 to .8 US gal./min. .4 to 3 l/min.
Even-spray poly — The ES nozzle produces a flat, even spray which provides uniform distribution across the spray band. It is an excellent choice for band applications of pre and post-emergent herbicides and fungicides, and directed post applications. The band width can be changed by adjusting the spray nozzle height. Made from polyacetal, the ES nozzle provides superior wear resistance to agricultural chemicals. • • • •
46
Provides uniform distribution across the spray band Excellent choice for pre and post-emergent herbicides and fungicides and direct post applications Width can be adjusted by spray nozzle height Provides superior wear resistance
JOHN DEERE SPRAY PARTS Even Spray (ES)
gpm @ 40 psi 0.10 0.15 0.20 0.30 0.40 0.50 0.60 0.80
ES 80 deg. — ASABE droplet classification data 30 psi F M M C C C C VC
40 psi F F M M C C C C
50 psi F F M M M C C C
60 psi F F F M M C C C
Nozzle 10 pack PSES8001 PSES80015 PSES8002 PSES8003 PSES8004 PSES8005 PSES8006 PSES8008
47
JOHN DEERE SPRAY PARTS Chemical Resistant (CR)
Spray pattern: 110-deg. tapered flat fan Capacity: .2 to 1.5 US gal./min. .75 to 6 l/min. Chemical-resistant polyvinylydene fluoride — The CR nozzle with its simple, one-piece design creates a flat sheet of spray and provides a consistent pattern over a range of pressures. The mixed droplet spectrum makes this product suited for applications of herbicides, fungicides, insecticides, and PGRs. It also allows effective delivery and retention of agrochemicals. The CR nozzle is produced from polyvinylydene fluoride for use in demanding chemical situations, such as acid-based defoliation products. • • •
48
Applications of herbicides, fungicides, insecticides and PGRs Creates flat sheet of spray and provides consistent pattern over a range of pressures Molded from polyinylydene fluoride for use in demanding chemical situations, such as acidbased defoliation products
JOHN DEERE SPRAY PARTS Chemical Resistant (CR) gpm @ 40 psi 0.20 0.30 0.40 0.50 0.60 0.80 1.00 1.50
CR 110 deg. — ASABE droplet classification 30 psi F M M M M C C C
40 psi F F M M M C C C
50 psi F F M M M C C C
60 psi F F F M M C C C
Nozzle 10 pack PSCR1002 PSCR1003 PSCR1004 PSCR1005 PSCR1006 PSCR1008 PSCR1010 PSCR1015
49
JOHN DEERE SPRAY PARTS Off center — OC— brass nozzle
Spray pattern: off center Capacity: .2 to .6 US gal./min. .75 to 2.27 l/min.
Off-center brass — The OC nozzle produces a flat spray for use on boom ends to extend spray reach, improve coverage, and reduce risk of equipment damage. Made from brass, the OC is intended for moderate use. • • • •
50
Produces a flat spray for use on boom ends to extend spray reach Reduce risk of equipment damage Made from brass Intended for moderate use
JOHN DEERE SPRAY PARTS Off center — OC— brass nozzle
gpm @ 40 psi 0.20 0.30 0.40 0.60
OC 80 deg. – ASABE droplet classification data 30 psi M M C C
40 psi M M M C
50 psi M M M M
60 psi F F M M
Nozzle 10 pack PSOCB8002 PSOCB8003 PSOCB8004 PSOCB8006
51
JOHN DEERE SPRAY PARTS Fence Row/Boomless (XT) Spray pattern: off center, distances up to 16.5 ft. Capacity: 1.0 to 2.4 US gal./min. 3.7 to 9 l/min. Fence Row/Boomless- XT introduces boomless spray technology, enabling spray to be targeted into places that conventional booms and other nozzles cannot reach. • • • •
52
Common uses include orchard, vineyard, forestry, pasture, turf and golf courses. Excellent low-drift option while extending spray reach Maintains a consistent spray swath over a pressure range of 30-60psi 105 degree spray angle
JOHN DEERE SPRAY PARTS Fence Row/Boomless (XT) Capacity and spacing data
Flow rate replaced at 20-in. spacing Effective Number of Flow rate distance (ft.) tips replaced per tip
Part number
psi
gpm
Distance (ft.)
PSXTIQ10
40.0
1.0
16
14.5
8.7
0.115
80 or 110 deg. 0.1 gpm
5.8
0.172
80 or 110 deg. 0.2 gpm
PSXTIQ20
40.0
2.0
17
15.5
9.3
0.215
80 or 110 deg. 0.2 gpm
6.2
0.323
80 or 110 deg. 0.3 gpm
PSXTIQ24
40.0
2.4
18
16.5
9.9
0.242
80 or 110 deg. 0.25 gpm
6.6
0.364
80 or 110 deg. 0.4 gpm
Replacement parts
Description
PM3489H PM3488H PM3488A PM3489A PM3488B PM3489B
XT010 stainless-steel insert XT010 polyacetal pattern generator XT020 stainless-steel insert XT020 polyacetal pattern generator XT024 stainless-steel insert XT024 polyacetal pattern generator
Thread size 1/4
in. 1/4 in. 3/8 in. 3/8 in. 1/2 in. 1/2 in.
Type of tip replaced
Flow rate replaced at 30-in. spacing Number of Flow rate tips replaced per tip
Type of tips replaced
Pkg. qty.
1 1 1 1 1 1
53
JOHN DEERE SPRAY PARTS Twin caps
TwinCapTM- TwinCap is a simple, compact way of accommodating two spray tips back to back. This design allows you to apply the volume per acre you want, at the speed you want, without compromising spray quality. • Improve control of plant diseases, insects, and difficult weeds • Twin 30° angles improve canopy penetration • Combined forward and backward angles enhance coverage on stems and leaves • Holds any two standard dimension tips: ULA, LD, LDC, ER, ERI, Flat and Even nozzles (sold separately) Part number PMTC PM1TC PMTCCR PM65MN01113
54
Description Twin cap Twin cap Twin cap internal seal
Pkg. qty. 6 40 6
Twin cap, chemical resistant
6
JOHN DEERE SPRAY PARTS Adapters for nozzle body • • • •
Use John Deere spray nozzles and quick-change caps on Hardi® or Jacto™ sprayers. Converts Hardi or Jacto nozzle bodies to standard quick-change lugs. Adds only 1/2-in. to length of nozzle body. Adapter and EPDM gasket included
Part number PM99500024 PM99500027
Description Hardi adapter Jacto adapter
Pkg. qty. 10 10
Hardi is a registered trademark of Hardi, Inc. Jacto is a registered trademark of Jacto, Inc.
55
JOHN DEERE SPRAY PARTS Spray Nozzle Caps Spray Nozzle Caps — Caps provide trouble-free spray nozzle installation and sealing on nozzle bodies and several other common makes. • Color coded to ISO standards for nozzle flow to simplify nozzle selection and identification in the field • Caps for fan pattern nozzles automatically align nozzles for enhanced spray uniformity
56
JOHN DEERE SPRAY PARTS Spray Nozzle Caps
Fits:
ISO Standard Fan
European Fan (Thick body)
Standard Round (Non-aligning)
Shut-off
Threaded
ULA, LDA, LD, ER, ERI, OC, FF, ES, ERC
ULAC, STC
HC, D-C, FL flanged hose barbs
Blank
1/4”MNPT
Std. Pack
Black
PS90020
PS90120
PS90420
PS90920
PS91020
10
Orange
PS90001
PS90101
PS90401
-
-
10
Green
PS900015
PS901015
PS904015
-
-
10
Yellow
PS90002
PS90102
PS90402
-
-
10
Lilac
PS900025
PS901025
PS904025
-
-
10
Blue
PS90003
PS90103
PS90403
-
-
10
Dark Red
PS900035
-
-
-
-
10
Red
PS90004
PS90104
PS90404
-
-
10
Brown
PS90005
PS90105
PS90405
-
-
10
Gray
PS90006
PS90106
PS90406
-
-
10
White
PS90008
PS90108
PS90408
-
-
10
Included EPDM seal
PM200040-1 PM200040VI
PM200040-1 PM200040VI
PM200040-1 PM200040VI
PM65BS205 -
PM200040-1 PM200040VI
-
Included Nitrile seal Separate Viton seal
57
JOHN DEERE SPRAY PARTS Plumbing Products From nozzle bodies to pressure gauges to spray guns, we have what you need in plumbing accessories. See your dealer for information on the complete plumbing products line. • Nozzle bodies • Pressure guages • Fittings • Spray guns • Valves
58
JOHN DEERE SPRAY PARTS Pumps For today’s machinery and tomorrow’s demands, John Deere pumps are leaders in the industry. See your John Deere dealer to match the right pump to your equipment and task. • Centrifugal • Roller • Accessories
59
JOHN DEERE SPRAY PARTS Application support Foams, dyes, and cleaners stand up to tough, demanding conditions. From the long-lasting ULTRAX™ marking foam to our exclusive winterizer fluid, your John Deere dealer has all the products you need to support your spray application. • Foams • Dyes • Cleaners • Winterizer
60
JOHN DEERE SPRAY PARTS Liquid-handling products Liquid-handling products are made from glass-reinforced polypropylene. This high-quality material provides excellent chemical and corrosion resistance, rigidity, light weight, stress-cracking resistance, low moisture absorption, and good impact resistance. • Valves • Electric valves • Manifold systems • IBC/tank accessories • Polyproylene and 316 stainlesssteel couplings • Pipe fittings • Line strainers
61
DSPG43512 Litho in U.S.A. (11-04)
