SECTION 08 71 00 DOOR HARDWARE PART 1 GENERAL 1.01 SECTION INCLUDES A.
Hardware for wood and hollow metal swinging doors.
B.
Hardware for wood sliding doors.
1.02 RELATED SECTIONS A.
Wood Doors
1.03 REFERENCES A.
DHI (LOCS) - Recommended Locations for Architectural Hardware for Standard Steel Doors and Frames; Door and Hardware Institute; 2004.
B.
DHI WDHS.3 - Recommended Locations for Architectural Hardware for Flush Wood Doors; Door and Hardware Institute; 1993; also in WDHS-1/WDHS-5 Series, 1996.
1.04 ADMINISTRATIVE REQUIREMENTS A.
Coordinate the manufacture, fabrication, and installation of products onto which door hardware will be installed.
1.05 QUALITY ASSURANCE PART 2 PRODUCTS 2.01 MANUFACTURERS A.
Keys and Cylinders: ________ 1. Schlage: www.schlage.com.
F.
Wall and Floor Stops: 1. Ives Manufacturing: www.iveshardware.com
G.
Gasketing and Thresholds: ________ 1. Pemko Manufacturing Co: www.pemko.com.
H. Sliding Door Kits: ________ 1. Pemko Manufacturing Co: www.pemko.com. I. Substitutions: See Section 01 60 00 - Product Requirements. 2.02 GENERAL REQUIREMENTS FOR DOOR HARDWARE PRODUCTS A.
Provide products that comply with the following: 1. Applicable provisions of Federal, State, and local codes. 08 71 00 - 1 of 6
B.
Finishes: Identified in schedule at end of section.
2.03 CYLINDERS AND KEYING A.
Schlage Everest IC cores, Grand Master Keyed as directed by owner..
B.
Provide temporary cores during construction.
C.
Provide key quantities as follows unless directed by owner otherwise: - 3 Master Keys - 3 Cut Keys per change key - 3 Construction Keys
PART 3 EXECUTION 3.01 EXAMINATION A.
Verify that doors and frames are ready to receive work and dimensions are as indicated on shop drawings.
3.02 INSTALLATION A.
Install hardware in accordance with manufacturer's instructions and applicable codes.
B.
Use templates provided by hardware item manufacturer.
C.
Mounting heights for hardware from finished floor to center line of hardware item: As listed in Schedule, unless otherwise noted: 1. For steel doors and frames: Comply with DHI "Recommended Locations for Architectural Hardware for Steel Doors and Frames." 2. For wood doors: Comply with DHI "Recommended Locations for Architectural Hardware for Wood Flush Doors."
3.03 FIELD QUALITY CONTROL A.
Provide an Architectural Hardware Consultant to inspect installation and certify that hardware and installation has been furnished and installed in accordance with manufacturer's instructions and as specified.
3.04 ADJUSTING A.
Adjust work under provisions of Section 01 70 00.
B.
Adjust hardware for smooth operation.
3.05 PROTECTION A.
Protect finished Work under provisions of Section 01 70 00.
B.
Do not permit adjacent work to damage hardware or finish.
08 71 00 - 2 of 6
HARDWARE SETS
Group 1 Door # 103, 107, 101 3
Hinges
5BB1HW 4 ½” x 4 ½” NRP
630
Ives
1
Deadbolt
MS1850SN-410-4003ANSI
628
Adams Rite
1
Exit Indicator
4089
628
Adams Rite
2
Cylinders
26-062
626
Schlage
2
Push/Pull
8190HD-2 BTB
US32D Ives
1
Closer
1461 REG
AL
LCN
1
Floor Stop
FS448
26D
Ives
1
Weather-stripping
S88 D
Pemko
1
Door Sweep
3452 AV
Pemko
1
Threshold
272 A
Pemko
Group 2 Door # 100A, 102B 6
Hinges
5BB1HW 4 ½” x 4 ½” NRP
652
Ives
1
Flush bolt set
FB31P
32D
Ives
1
Lockset
AL80TD JUP
626
Schlage
1
IC Core
23-030
628
Schlage
2
Closers
1461 SCUSH
AL
LCN
1
Coordinator
COR52 x MB x FP
628
Ives
2
Dust Proof Strike
DP1
626
Ives
1
Weather-stripping
S88 D
Pemko
1
Astragal Set
18041 CNB
Pemko
2
Door Sweep
3452 AV
Pemko
1
Threshold
272 A
Pemko
08 71 00 - 3 of 6
Group 3 Door # 102A 3
Hinges
5BB1 4 ½” x 4 ½” NRP
630
Ives
1
Storeroom Lock
AL80TD JUP
626
Schlage
1
IC Core
23-030
626
Schlage
1
Closer
1461 SCUSH
AL
LCN
1
Weather-stripping
S88 D
Pemko
1
Door Bottom
3452 AV
Pemko
1
Threshold
272 A
Pemko
Group 4 Door # 104, 108, 110 3
Hinges
5BB1 4 ½” x 4 ½”
652
Ives
1
Privacy w/Indicator
L9496T 07A L583-363
626
Schlage
1
IC Core
23-030
626
Schlage
1
Wall Stop
WS407CCV
32D
Ives
Group 5 Door # 109 3
Hinges
5BB1 4 ½” x 4 ½” NRP
652
Ives
1
Lockset
AL80TD ATH
626
Schlage
1
IC Core
23-030
626
Schlage
1
Closer
1461 SCUSH
AL
LCN
1
Smoke Seal
S88 D
Pemko
Group 6 Door # 100, 106 4
Hinges
5BB1HW 5” x 4 ½” NRP
32D
1
Panic Device
25-R- EO-48”
US26D Falcon
1
Key Fob Trim
CO-200-993R-70-PRK-ATH-RD
626
Schlage
1
Cylinder Core
23-030
626
Schlage
1
Closer
1461 SCUSH
AL
LCN
1
Weather-stripping
S88 D
Pemko
1
Door Sweep
3452 AV
Pemko
1
Threshold
272 A
Pemko
7610
Schlage
50 Key Fobs
Ives
08 71 00 - 4 of 6
Group 7 Door # Unit Entry Door 3
Hinges
5BB1 4 ½” x 4 ½”
652
Ives
1
Entry Set
CS210TD JUP
626
Schlage
1
IC Core
23-030
626
Schlage
1
Closer
1261 REG
AL
LCN
1
Gasketing
S773 D
Pemko
1
Door Bottom
412 RL
Pemko
1
Wall Stop
WS407CCV
26D
Ives
Group 8 Door # Unit Bathroom Door 3
Hinges
5PB1 4 ½” x 4 ½”
652
Ives
1
Privacy Set
S40D JUP
626
Schlage
1
Hinge Pin or Wall Stop
70A / WS407CCV
26D
Ives
Group 9 Door # Unit Bedroom Door 3
Hinges
5PB1 4 ½” x 4 ½”
652
Ives
1
Passage Set
S10D JUP
626
Schlage
1
Hinge Pin or Wall Stop
70A / WS407CCV
26D
Ives
Group 10 Door # Bi-Pass Closet Door 1
Bi-Pass Kit
BPC150N
2
Flush Pulls
1115B BTB
Stanley 630
Trimco
652
Ives
626
Schlage
26D
Ives
Group 11 Door # Utility/Pantry/Closet Door 3
Hinges
1
Passage Set
1
Hinge Pin or Wall Stop
5PB1 4 ½” x 4 ½” S10D JUP 70A / WS407CCV
Group 12 Door # Pocket Door 1
Pocket Door Kit
PDC150N
1
Privacy Set
1065-175
Stanley 626
Trimco
08 71 00 - 5 of 6
Group 13 Door # Bi-Fold Door 1
Bi-Fold Kit
BFC150N
2
Wire Pulls
66
Stanley 626
Don-Jo
Group 14 Door # SA1, SB1, SA2, SB2, SA3, SB3, SA4, SB4, SA5, SB5 3