PICK UP TRUCK LIFT 1000 LB. 37555
Set up and Operating Instructions
Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com
Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 1998 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353. Revised 08f, 09f
Specifications Jack Capacity Winch Cable Boom Length Boom Height Post Pivots Ram Travel Base
3 T (The lift cannot support this much.) 1/4” steel, 25’ long with locking hook 53-1/2” 80” from base 360° 5” 7-3/8” x 9-1/2”, 1/2” thick steel
Capacity (lb.) 500 600 700 1000
Boom Length 53 1/2” 47” 40 1/2” 33 1/2”
Hole 1 2 3 4
Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions WARNING: When using winch, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this tool! 1.
Always wear ANSI approved impact safety goggles when operating the winch.
2.
Do not exceed winch load weight capacity (see specifications).
3.
Be certain winch is properly bolted to a truck bed that can hold the winch load.
4.
Always use proper couplings when connecting winch cable hook to load cable or rope.
5.
Do not overload the winch. Stay within the capacity levels shown in the specifications.
6.
Do not use inappropriate attachments to extend the length of the winch cable.
7.
Never lift people or hoist loads over people.
8.
Never come between the winch and the load when operating.
9.
Do not apply load to winch when cable is fully extended. Keep at least 4 full turns of cable on the reel.
10. After moving an item with the winch, secure the item. Do not rely on the winch to hold it for an extended period. The winch does not have a locking key. 11. Examine winch before using. Components may be affected by exposure to chemicals, salts, and rust. 12. Never fully extend cable while pulling a load. Keep 4 complete turns of cable around the winch spool. 13. Never operate winch if cable shows any signs of weakening, is knotted or kinked. 14. Never fully extend the cable while under load. REV 08g
SKU 37555
Page 2
15. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 16. Do not wear loose clothing or jewelry when operating. Wear protective hair covering to protect long hair. Uncovered long hair can get caught in moving parts. 17. Always set pickup truck parking brake and block tires when using lift. Vehicles with automatic transmissions should be left in “park.” Manual transmissions should be left in gear. Never attempt to lift something while the vehicle is moving. 18. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool.
Unpacking Open box and examine components. Look for any loose parts in the packing material before discarding. If any are found, try and find the part on the parts list or on the exploded view of the lift, and reinstall the part. If any part of the machine is missing or broken, please call Harbor Freight Tools at the number on the front cover as soon as possible.
Assembly While assembling the truck lift, refer to the Assembly Parts Illustration on the last page. 1.
Place the Base (01) in the location on the truck bed where it is to be secured. This flat location must be able to support the lift with a 1000 lb. load. (On most trucks, a desirable position is just behind the wheel so that the boom may be stored over the wheel well.)
2.
Using a pencil, mark through the mounting holes in the lift base (01) to mark drill holes.
3.
Using a power drill and appropriate drill bit size, drill holes through truck bed.
4.
Place the bolts (22) through the Base and into the truck bed holes.
5.
Place each Angle Steel (11) plate under the truck bed, over the protruding bolts (22), and secure with the washers (23), spring washers (24), and finally the nuts (25), as shown in the Assembly Parts Illustration. Tighten nuts (25) securely.
6.
Place the Post (02) upper lift assembly onto the Base (01). Insert Lock Pin (20).
Warning: The Lift has four extension settings for the Extendible Boom. Each setting has a weight limit that is clearly marked on the Boom. Do not exceed these weight limits as it may cause damage to the Pick Up Truck Lift and/or cause bodily injury.
SKU 37555
Page 3
Operation 1.
Release the Lock Pin (20) located on the Post (02), and swivel the Post so that the Boom (04) is pointing towards the object to be lifted.
2.
Position the Hook and Steel Cable (10) over the article to be moved by adjusting and locking the Extendible Boom (07) in place using the Boom Extendible Pin (08).
Do not exceed the weight limits of the lift (See specification table).
3.
Hook around the article so that its weight is centered.
4.
Place the slotted end of the Jack Handle (21) over the Jack release valve, and close it by turning it in a clockwise direction.
5.
Insert the Jack Handle into its connector and lift the Boom by pumping the handle in an up and down motion.
6.
When the article has been lifted to the desired height, it may be moved over the truck bed by slowly swiveling the Post (02) until the article is directly over the truck bed.
Do not attempt to extend the Boom further while the article is still attached. If the article needs to be moved further out, lower it, then adjust the Boom and relift it. 7.
Lower the article onto the truck bed by using the Jack Handle (21) to slowly turn the pump release valve in a counterclockwise direction.
8.
Reverse previous steps to remove article from truck bed.
9.
Secure boom over truck wheel well using the Lock Pin (20).
SKU 37555
Page 4
Maintenance 1.
Clean and lubricate all moving parts including gears, ratchets, and shafts to insure safe operation. When not in use, keep clean, dry, and covered.
2.
Purge air from hydraulic system when jack does not lift efficiently.
3.
Replace hydraulic oil once per year.
Purging Air from the Hydraulic System Note: Occasionally, air bubbles can become trapped inside the hydraulic system thereby reducing the efficiency of the jack. Purge air from the system as needed. 1.
Place the slotted end of the Jack Handle (21) over the valve release screw.
2.
Turn the valve release screw (not shown) 1-1/2 turns counterclockwise using the Jack Handle.
3.
Remove the oil filler plug on the side of the Jack (not shown) by gently pulling and turning.
4.
Rapidly pump the Jack Handle several times to purge air from the hydraulic system.
5.
Turn the valve release screw clockwise until snug using the Jack Handle.
6.
Replace the oil filler plug.
Replacing Hydraulic System Oil Caution: Replace the oil once per year, or more often with heavy use. Do not permit dirt or any substance other than high quality hydraulic jack oil to enter the hydraulic system. Do not mix different kinds of oil together. 1.
Remove the Jack (12) from the lift and place in an upright position.
2.
Completely lower ram.
3.
Remove the oil filler plug (not shown) from the Jack.
4.
Fill with high-quality hydraulic jack oil to the lower rim of the fill hole.
5.
Purge air from the system as previously described.
6.
Top off with more hydraulic jack oil.
7.
Replace the oil filler plug.
SKU 37555
Page 5
Parts List Part 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Description
Base Post Grease Fitting Boom Retracted Pin 12x84 Cotter Pin Extendible Boom Pin, Boom Extendible Windlass Hook and Steel Cable Angle Steel 3 Ton Jack Bearing Jack Support Washer Spring Washer Bolt M6x15 Pin 12x78 Pin 12x48 Lock Pin Jack Handle Bolt M12x50 Washer Spring Washer Nut M12
Qty 1 1 1 1 1 3 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 5 5 5 5
Assembly Parts Illustration
SKU 37555
Page 6
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 37555
Page 7
