CAP FLASHING (CHOOSE ONE) GGGG Flashings to be a maximum width of 39.5" (width of IN IN HH GG IN IN SH IN H G AS HIN COMMERCIAL & INDUSTRIAL AA HIN SSS LFLALA BASE FLASHING (CHOOSE ONE) ONE) roll), installed LS in the machine direction and staggered PPFF L AHS F CAP MEMBRANE (CHOOSE P A F L A PLF AAA BASE MEMBRANE (CHOOSE ONE) a minimum of 12" from all joints. All side laps shall PFP CCC TP-180-CAP A C CACPA E

ANNEE

C

EE N NEN BBR AAA R TP-250-CAP RR B TP-180-FF-BASE be 3.5". EEM ARNA BRB M MM E BM MM EME PPM A M E P CCAAA PM M TP-250-CAP (5.0)180 * TP-180-CAP ARMOURBOND CCPAP recommendations CRCA in CAC GG COVERTP-180 BOARD VAPOR RETARDERS (CHOOSE ONE)IKO supports All capthe sheet side laps shall of bethe 3.5". IN TF-95-FF-BASE HIN INGGG IN PREVENT G ASSH SHH TP-250-CAP ARMOURBOND FLASH * INSULATION IN HIN FLFLLALAASHS that 2 ply flashings are F cap sheetreinforced end laps shall be 6". All polyester E A S SE AS SEEFEFLFAL TF-95-FF-BASE (22) ASE PREVENT TP-250 BBA & B S A desirable due to their superior elongation and tear APP CLASSIC ** B SA The side and end laps of the cap TP-250-CAP (5.0) EEEE NN BAB E AAN RR AA NEN IKO MVP * -PREMIUM Is a self-adhering vapor membrane. It sheet isascomposed of AN BBR PROTECTOBOARD - Is composed of aretardant mineral-fortified asphaltic core between strength opposed fiberglassareinforced PREVENT TP-250 BB MM TP-180-FF-BASE RAR shall beto staggered minimum flashings. BR EEM EE MM MBM PREVENT TP-180 M IKOTHERM Is a rigid polyisocyanurate insulation with high thermal properties. It is E E STEEL modified rubber asphalt with a top surface film of high density cross laminated SE EEMEMM S A two non-woven glass fiber mats. Protectoboard may be used as a cover board S E Flashings to be a maximum width of 39.5" (width of roll), installed in the machine direction and of 12" from all joints. AA APP CLASSIC* SESM BBA AS 180cell * polyisocyanurate ARMOURBOND BBB constructed from aproduct closed foam core bonded onBINDER each to glass TECHNICAL REFERENCE PREVENT TP-250 polyethylene. should not all be board applied temperatures BA IKOTherm insulation, a re-cover in aside re-roof or-10°C. anyside over staggered aThis minimum ofas 12" from joints. Allat lapsinstallation, shall below be 3.5". DDDD RR APP GRANULAR DD AAR AA fiber reinforced facers during the manufacturing process. RR BOO AR ARMOURBOND FLASH * as a new substrate forI a3.34, ADR OOO RRBBBB 6.17.1(Part 8) applied noSTEEL DECK other application where it isTP-250 used modified bitumen or coating *4.17.1, Requires approved PREMIUM PREVENT ER ROBAO VE E R E V B V O ERER V STEEL DECKS Must be a minimum of 22 gauge, manufactured from milled steel * Requires approved coating applied no sooner than 30 OOO CC VEV C IKO supports the recommendations of the CRCA in that 2 ply polyester reinforced flashings are ARMOURGARD VAPOR RETARDANT ** Composed of two layers of kraft O sooner than 30 days and no later than BUR roofing membrane. CCVO I 3.28 - 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1 APP CLASSIC ** COC APP CLASSIC days and no later than 90or days after membrane application. NOTE: IKOTherm III * with acrylic-coated facers and IKOTherm 25reinforcement psi as are also available. and be factory primed galvanized to resist rusting. N desirable due to their superior elongation and tear strength fiberglass reinforced flashings. paper bonded together with asphalt. Strands of fiberglass aretomembrane Modified Bitumen Heat Weld 90opposed days after application. IONO NN TIO ITOIINON LAATT First layer must be mechanically attached orstrength cold-applied with approved ahesive by IKO, APP GRANULAR T LAIO UULU intertwined near each edgeattached, for added and tear resistance. LAA NOTE: Can be mechanically cold applied or hot mopped. LTA ULU INSS S IN S N * Requires approved self-adhering membrane primer. RSSSS INIINUS TECHNICAL BINDER TECHNICAL REFERENCE unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, coldBINDER applied or R EER EER INS DDD SRS DRE ARRR RED I Steel ETETATTAADR ** Use only with APP Classic or APP Granular cap flashings. E 3.11 R hot mopped. Refer to IKO REFERENCE Commercial Technical Binder for fastening patterns. EATRA RRRE R * Self-adhering membrane may require self-adhering primer. I 3.30 - 3.31, 4.16.1, 6.16.1 TECHNICAL BINDER T R O RRER PO base sheet side laps shall be 3.5". 6.07.1, All base9.07.1 sheet end laps shall be 6". The side and OR AP PPO I All AAO Roof Decks Re-Cover - 3.20, RO VVA VVP ** ArmourGard Vapor is4.07.1, adhered with ArmourGard Vapor Retardant AP VAV Accessories, Options &staggered Additional Considerations TECHNICAL BINDER REFERENCE laps of the baseRetardant sheet shall be a minimum of 12" from Adhesive. all joints. I end 3.25 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1 TECHNICAL BINDER REFERENCE ELELLLL EL TETEEE 3.34, 4.17.1, 6.17.1, Part 8membrane primer. EE approved self-adhering *Requires TECHNICAL BINDER TEE SSTSS TT I 3.25 - 3.27, SS 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 ** Only to be used in conjunction with APP Classic or APP Granular Cap.  3.28 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1 I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

ROOFING PRODUCTS

COMMERCIAL INDUSTRIAL STEEL DECK

ROOFING PRODUCTS Modified Bitumen Heat Weld

Drainage BINDER - 3.09 REFERENCE TECHNICAL 

3.28 - 3.29, 4.14.1, 6.14.1, 9.14.1 Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Temporary Closures - 4.19.1, 6.19.1, 9.19.1 Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21

F

P G C AH I N S LA P NE CA RA

NOTE: Use of the above may or may not be applicable to your specific roof.

M

EM

B

SE G BA HIN

FL

AS

SE ANE A B R

M

EM

C

ER V O RD

BO

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

B

SU

A

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

GGGG IN IN HH GG IN IN SH IN H G AS HIN AA HIN SSS LFLALA LS PPFF L AHS F P A F L A PLF AAA PFP CCC A C C PA EE CAC AAN EE N NN BBR ENE AA R RR B EEM ARNA MM BRB M M E EMEBM PPMMM A E P CCAAA PM M CCPAP CAC GG IN HIN INGGG IN G ASSH SHH IN HIN FLFLLALAASHS F E A S SE AS SEEFEFLFAL ASE BBA B S A B SA EEEE NN BAB E AAN RR AA NEN AN BBR BB MM RAR BR EEM EE MM MBM M E E SE EEMEMM S A S E AA SESM BBA AS BBB BA DDDD RR DD AAR AA RR BOO AR ADR OOO RRBBBB ER ROBAO VE E R E V B V O ERER V OOO VEV CCC O CCVO COC N IONO NN TIO ITOIINON LAATT T LAIO UULU LAA LTA ULU INSS S IN S N RSSSS INIINUS R EER EER INS DDD SRS DRE ARRR RED ETETATTAADR E R EATRA RRRE R T R O RRER PO OR AP PPO AAO RO VVA VVP AP VAV

CAP FLASHING (CHOOSE ONE) Flashings to be a maximum width of 39.5" (width of BASE FLASHING (CHOOSE ONE) ONE) roll), installed in the machine direction and staggered CAP MEMBRANE (CHOOSE BASE MEMBRANE (CHOOSE ONE) a minimum of 12" from all joints. All side laps shall TP-180-CAP

TP-250-CAP TP-180-FF-BASE be 3.5". TP-250-CAP (5.0)180 * TP-180-CAP ARMOURBOND recommendations CRCA in COVERTP-180 BOARD VAPOR RETARDERS (CHOOSE ONE)IKO supports All capthe sheet side laps shall of bethe 3.5". TF-95-FF-BASE PREVENT TP-250-CAP ARMOURBOND FLASH * INSULATION that 2 ply flashings are cap sheetreinforced end laps shall be 6". All polyester TF-95-FF-BASE PREVENT TP-250 & desirable to and theirend superior elongation APP CLASSIC **(22) Thedue side laps of the cap and tear TP-250-CAP (5.0) IKO MVP * Is a self-adhering vapor membrane. It sheet isascomposed of PROTECTOBOARD - Is composed of aretardant mineral-fortified asphaltic core between strength opposed to fiberglassareinforced PREVENT PREMIUM TP-250 TP-180-FF-BASE shall be staggered minimum flashings. PREVENT IKOTHERM - TP-180 Isglass a rigid polyisocyanurate insulation with high thermal properties. It is STEEL modified rubber asphalt with awidth top surface film(width of high cross laminated two non-woven fiber mats. Protectoboard may be used a 12" cover board Flashings to be a maximum of 39.5" of density roll), as installed in theall machine of from joints. direction and APP CLASSIC* 180 * ARMOURBOND constructed from aproduct closed as cellapolyisocyanurate foam core bonded onBINDER each to glass TECHNICAL REFERENCE PREVENT TP-250 polyethylene. not all be board applied temperatures IKOTherm insulation, in aside re-roof or-10°C. anyside over staggered aThis minimum ofshould 12"re-cover from joints. Allat lapsinstallation, shall below be 3.5". APP GRANULAR fiber reinforced facers during the process. ARMOURBOND FLASH * manufacturing 6.17.1(Part 8) applied noSTEEL DECK other application where it isTP-250 used as a new substrate forI a3.34, modified bitumen or coating *4.17.1, Requires approved PREMIUM PREVENT STEEL DECKS - Must be a applied minimum ofof22the gauge, from milled steel * Requires approved coating no sooner than 30 manufactured IKO supports theVAPOR recommendations CRCA in that 2 ply polyester reinforced are ARMOURGARD RETARDANT ** - Composed of two layers of30 kraft sooner than days andflashings no later than BUR roofing membrane. I APP CLASSIC ** 3.28 -are 3.31, 4.14.1, 4.16.1, 6.14.1, 6.16.1 APP CLASSIC days and no later than 90or days after membrane application. NOTE: IKOTherm III * with acrylic-coated facers and IKOTherm 25 psi as also 3.29, available. and be factory primed galvanized to resist rusting. desirable due to their superior elongation and tear strength fiberglass reinforced flashings. paper bonded together with asphalt. Strands of fiberglass reinforcement aretomembrane Modified Bitumen Heat Weld 90opposed days after application. First layer must be mechanically attached or cold-applied with approved ahesive by IKO, APP GRANULAR intertwined near each edge for added strength and tear resistance. NOTE: Can be mechanically attached, cold applied or hot mopped. * Requires approved self-adhering membrane primer. TECHNICAL BINDER TECHNICAL REFERENCE unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, coldBINDER applied or I Steel ** Use only withtoAPP or APPTechnical GranularBinder cap flashings. - 3.11 hot mopped. Refer IKOClassic Commercial for fastening patterns. * Self-adhering membrane may require self-adhering primer. I 3.30 - 3.31, 4.16.1, 6.16.1 TECHNICAL BINDER REFERENCE base sheet side laps shall be 3.5". 6.07.1, All base9.07.1 sheet end laps shall be 6". The side and I All Roof Decks Re-Cover - 3.20, ** ArmourGard Vapor is4.07.1, adhered with ArmourGard Vapor Retardant Accessories, Options &staggered Additional Considerations TECHNICAL BINDER REFERENCE laps of the baseRetardant sheet shall be a minimum of 12" from Adhesive. all joints. I end 3.25 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1 TECHNICAL BINDER REFERENCE ELELLLL EL  TETEEE 3.34, 4.17.1, 6.17.1, Part 8 EE self-adhering membrane primer. * Requires approved TECHNICAL BINDER TEE SSTSS TT I 3.25 - 3.27, SS 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 ** Only to be used in conjunction with APP Classic or APP Granular Cap.  3.28 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1 I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

COMMERCIAL INDUSTRIAL

ROOFING PRODUCTS

Drainage BINDER - 3.09 REFERENCE TECHNICAL 

3.28 - 3.29, 4.14.1, 6.14.1, 9.14.1 Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Temporary Closures - 4.19.1, 6.19.1, 9.19.1 Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21

F

P G C AH I N S LA P NE CA RA

NOTE: Use of the above may or may not be applicable to your specific roof.

M

EM

B

SE G BA HIN

FL

AS

SE ANE A B R

M

EM

C

ER V O RD

BO

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

B

SU

A

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

GGGG IN IN HH GG IN IN SH IN H G AS HIN AA HIN SSS LFLALA LS PPFF L AHS F P A F L A PLF AAA PFP CCC A C C PA EE CAC E AANNN EE NEN A BBRRR ANA RAR B EEMMM BRB M M E EMEBM PPMMM A E P CCAA PM PM APA CC CAC GG IN HIN INGGG IN G ASSH SHH HIN FLFLALAASH SIN F E L A S SE AS SEEFEFLFAL ASE BBA B S A B SA EEEE NN BAB E AAN RR AA NEN AN BBR MM BB RAR BR EEM MM EE MBM M E E SE EEMEMM S A S E AA SESM BBA AS BBB BA DDD DD AR AA RRR AR O BO BB ADR OO AO R RRBOB E E R E V B V ERER V OOO VEV CC O CCVO COC N IONO TIO NN ITOIINON LAATT T LAIO SUULU LAA LTA INSN ULU S IN S RSSS INIINUS DEER ERRS INS DESRS ARRDRD EDRE ETETATTAAR D R E R E RA R RE TAT ORRRRR PO ORER AP PPO AAO RO VVA VVP AP V A V

BASEMEMBRANE FLASHING (CHOOSE (CHOOSE ONE) ONE) CAP BASE MEMBRANE (CHOOSE ONE)

TP-180-FF-BASE TP-180-CAP ARMOURBOND 180 * COVER RETARDERS BOARD VAPOR (CHOOSE ONE) All cap sheet side laps shall be 3.5". TF-95-FF-BASE TP-250-CAP ARMOURBOND FLASH * INSULATION All cap sheet end laps shall be 6". TF-95-FF-BASE (22) APP CLASSIC ** The side and end laps of & the cap TP-250-CAP (5.0) IKO MVP * - Is a self-adhering vapor membrane. It sheet is composed PROTECTOBOARD - Is composed of aretardant mineral-fortified asphaltic core between TP-180-FF-BASE shall be of staggered a minimum PREVENT TP-180 IKOTHERM Is a rigid polyisocyanurate insulation with high thermal properties. It is modified rubber asphalt with awidth top surface film(width of high cross laminated twoSTEEL non-woven glass fiber mats. Protectoboard may be used a 12" cover board Flashings to be a maximum of 39.5" of density roll), as installed in theall machine of from joints. direction and 180cell * polyisocyanurate ARMOURBOND constructed from aproduct closed foam core installation, bonded on each PREVENT TP-250 polyethylene. should not all be board applied temperatures IKOTherm insulation, a re-cover in aside re-roof or-10°C. anyside to glass over staggered aThis minimum ofas 12" from joints. Allat laps shall below be 3.5". fiber reinforced facers during the process. ARMOURBOND FLASH * manufacturing other application where it isTP-250 used as a new substrate for a modified bitumen or coating applied noSTEEL DECK * Requires approved PREMIUM PREVENT STEEL DECKS Must be a minimum of 22 gauge, manufactured from milled steel IKO supports the recommendations of the CRCA in that of 2 ply polyester reinforced are ARMOURGARD VAPOR RETARDANT ** Composed two layers of30 kraft sooner than days andflashings no later than BUR roofing membrane. APP CLASSIC ** APP CLASSIC NOTE: IKOTherm III * withor acrylic-coated facers and IKOTherm 25reinforcement psi as are also available. and bebonded factory primed galvanized to resist rusting. desirable due to their superior elongation and tear strength fiberglass reinforced flashings. paper together with asphalt. Strands of fiberglass aretomembrane Modified Bitumen Heat Weld 90opposed days after application. First layer must be mechanically attached orstrength cold-applied with approved ahesive by IKO, APP GRANULAR intertwined near each edgeattached, for added and tear resistance. NOTE: Can be mechanically cold applied or hot mopped. * Requires approved self-adhering membrane primer. TECHNICAL BINDER TECHNICAL REFERENCE unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, coldBINDER applied or I Steel ** Use only withtoAPP or APPTechnical GranularBinder cap flashings. - 3.11 hot mopped. Refer IKOClassic Commercial for fastening patterns. * Self-adhering membrane may require self-adhering primer. I 3.30 - 3.31, 4.16.1, 6.16.1 TECHNICAL BINDER REFERENCE base sheet side laps shall be 3.5". 6.07.1, All base9.07.1 sheet end laps shall be 6". The side and I All Roof Decks Re-Cover - 3.20, ** ArmourGard Vapor is4.07.1, adhered with ArmourGard Vapor Retardant Accessories, Options &staggered Additional Considerations TECHNICAL BINDER REFERENCE laps of the baseRetardant sheet shall be a minimum of 12" from Adhesive. all joints. I end 3.25 3.27, 4.11.1, 4.12.1, 6.11.1, 6.12.1 TECHNICAL BINDER REFERENCE ELELLL L TETEE E  3.34, 4.17.1, 6.17.1, Part 8 self-adhering membrane primer. * Requires approved TECHNICAL BINDER TEEEL SSTSS TE I 3.25 - 3.27, TE SS 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 ** Only to be used in conjunction with APP Classic or APP Granular Cap.  3.28 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1 I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

COMMERCIAL INDUSTRIAL

ROOFING PRODUCTS

Drainage BINDER - 3.09 REFERENCE TECHNICAL 

3.28 - 3.29, 4.14.1, 6.14.1, 9.14.1 Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Temporary Closures - 4.19.1, 6.19.1, 9.19.1 Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21

P NE CA RA

NOTE: Use of the above may or may not be applicable to your specific roof.

M

EM

B

SE G BA HIN

FL

AS

SE ANE A B R

M

EM

C

ER V O RD

BO

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

B

SU

A

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

GG IN G GG IN IN SSHHH IN G HIN LLAAA S HIN SHS A LSA FL PPF F A F L A PLF CCAA PFP APA CC EE CAC E AANNN EE NEN A BBRRR ANA RAR B EEMMM BRB M M E EMEBM PPMMM A E P CCAA PM PM APA CC G CAC HIN INGGG IN G ASSHH HIN FFLLAASH SIN E L A S S EF AL BBAASSEFELF BASAES NNEEE BAB E N RRAAA ANNE MMB BB RAR BR MME EE MBM E E SSEEMEMM A E S BBAA ASSE M BB BA D DDD AA RRR AR O BB ADR OO AO RRBOB E R E B V ERER V OO VEV C O CCVO COC N N TIO NN O ITOIINO LAT T LAIO SUU LAA LTA INN ULU S S S INIINUS S EERRRSS INS E RDDDR ESR TAAARRED TRADR RREEETT R A R E T RER POOORR VVAAAPPRO VPAOP VAV

BASE MEMBRANE FLASHING (CHOOSE ONE) BASE (CHOOSE ONE)

TP-180-FF-BASE ARMOURBOND 180 * COVER RETARDERS BOARD VAPOR (CHOOSE ONE) TF-95-FF-BASE ARMOURBOND FLASH * INSULATION TF-95-FF-BASE (22) & APP CLASSIC ** IKO MVP * - Is a self-adhering vapor membrane. It is composed of PROTECTOBOARD - Is composed of aretardant mineral-fortified asphaltic core between TP-180-FF-BASE IKOTHERM - Isglass a rigid polyisocyanurate insulation with high thermal properties. It is STEEL modified rubber asphalt with awidth top surface film(width of high cross laminated two non-woven fiber mats. Protectoboard may be used a cover Flashings to be a maximum of 39.5" of density roll), as installed in board the machine direction and 180cell * polyisocyanurate ARMOURBOND constructed from a closed foam core bonded on each polyethylene. This product should not be applied at temperatures below IKOTherm insulation,ofas12" a re-cover re-roof or-10°C. anyside to glass over staggered a minimum from all board joints. in Allaside lapsinstallation, shall be 3.5". fiber reinforced during the process. ARMOURBOND FLASH * manufacturing other applicationfacers where it is used as a new substrate for a modified bitumen or STEEL DECK STEEL DECKS - Must be a minimum ofof22the gauge, manufactured from milled steel IKO supports theVAPOR recommendations in that of 2 ply flashings are ARMOURGARD RETARDANT **CRCA - Composed twopolyester layers of reinforced kraft BUR roofing membrane. APP CLASSIC ** NOTE: IKOTherm III their withor acrylic-coated facers and IKOTherm 25reinforcement psi as areopposed also available. and bebonded factory primed galvanized to resist rusting. desirable due to superior elongation and tear strength flashings. paper together with asphalt. Strands of fiberglass areto fiberglass reinforced Modified Bitumen Heat Weld First layer must be mechanically attached or cold-applied with approved ahesive by IKO, intertwined near each edge for added strength and tear resistance. NOTE: Can be mechanically attached, cold applied or hot mopped. * Requires approved self-adhering membrane primer. TECHNICAL BINDER unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, cold applied or I Steel ** Use only withtoAPP or APPTechnical GranularBinder cap flashings. - 3.11 hot mopped. Refer IKOClassic Commercial for fastening patterns. * Self-adhering membrane may require self-adhering TECHNICAL BINDER REFERENCE base sheet side laps shall be 3.5". All baseprimer. sheet end laps shall be 6". The side and I All Roof Decks Re-Cover 3.20, 4.07.1, 6.07.1, 9.07.1 ** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Accessories, &staggered Additional Considerations TECHNICAL BINDER REFERENCE laps of the base Options sheet shall6.11.1, be of 12" from Adhesive. all joints. I end 3.25 - 3.27, 4.11.1, 4.12.1, 6.12.1a minimum TECHNICAL BINDER REFERENCE LL L EEEEE LL  3.34, 4.17.1, 6.17.1, Part 8 SSTTE EE self-adhering membrane primer. * Requires approved TECHNICAL BINDER TE TT S I 3.25 - 3.27, SS 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 ** Only to be used in conjunction with APP Classic or APP Granular Cap.  3.28 3.31, 3.29, 4.14.1, 4.16.1, 6.14.1, 6.16.1 I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

COMMERCIAL INDUSTRIAL

ROOFING PRODUCTS

Drainage BINDER - 3.09 REFERENCE TECHNICAL 

3.28 - 3.29, 4.14.1, 6.14.1, 9.14.1 Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Temporary Closures - 4.19.1, 6.19.1, 9.19.1 Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

SE G BA HIN

FL

AS

SE ANE A B R

M

EM

C

ER V O RD

BO

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

B

SU

A

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

BASE MEMBRANE

G IN INGGG SHIN IN LLAASSHH NG ASAHSIH FLA PPF A F L CCAPFPLF CAPA E CAC AANNEEE N BBRRAN RARAEN EEMMBR M B M P MMEMEBM EM CCAAPPM CAPAP G CAC HIN INGGG IN G ASSHH HIN FFLLAASH SIN E L A S S EF AL BBAASSEFELF BASAES NEE BAB E RAANN AE MB BRR AN BR MME EMM B E E SSEMEM A E BBAS M BASE BA RDD AARDRD BOO AORA RBOB E R B V OVERER CCOVOEV COC N ION ATIONO N I ULATIO LALTAT INS ULU S S US INS ERRS N I N I RDDE S TAAR RESR RREETTRADRED R A POOR ERTE VVAAP ROR PAOP V A V

(CHOOSE ONE)

COVER RETARDERS BOARD VAPOR (CHOOSE ONE) TF-95-FF-BASE

TF-95-FF-BASE (22) & IKO MVP * - Is a self-adhering vapor membrane. It is composed of PROTECTOBOARD - Is composed of aretardant mineral-fortified asphaltic core between TP-180-FF-BASE IKOTHERM - Isglass a rigid polyisocyanurate with highasthermal properties. It is STEEL modified rubber asphalt with a top surfaceinsulation film may of high cross laminated two non-woven fiber mats. Protectoboard be density used a cover board 180cell * polyisocyanurate ARMOURBOND constructed from a closed foam core bonded on each side to glass polyethylene. This product should not be applied at temperatures below -10°C. over IKOTherm insulation, as a re-cover board in a re-roof installation, or any fiber reinforced during the process. ARMOURBOND FLASH * manufacturing other applicationfacers where it is used as a new substrate for a modified bitumen or STEEL DECK STEEL DECKS - Must be a minimum of 22 gauge, manufactured milled steel ARMOURGARD VAPOR RETARDANT ** - Composed of twofrom layers of kraft BUR roofing membrane. APP CLASSIC ** NOTE: IKOTherm III withor acrylic-coated andof IKOTherm psi are also available. and bebonded factory primed galvanized to resist rusting. paper together with asphalt. facers Strands fiberglass25reinforcement are Modified Bitumen Heat Weld First layer must be mechanically attached or cold-applied with approved ahesive by IKO, intertwined near each edge for added strength and tear resistance. NOTE: Can be mechanically attached, cold applied or hot mopped. TECHNICAL BINDER unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, cold applied or I Steel - 3.11 hot mopped. Refer to IKO REFERENCE Commercial Technical Binder for fastening patterns. * Self-adhering membrane may require self-adhering TECHNICAL BINDER base sheet side laps shall be 3.5". All baseprimer. sheet end laps shall be 6". The side and I All Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1 ** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Accessories, &staggered Additional Considerations laps of the base Options sheet shall6.11.1, be a minimum of 12" from Adhesive. all joints. I end 3.25 3.27, 4.11.1, 4.12.1, 6.12.1 TECHNICAL BINDER REFERENCE L EEELL L SSTTEEEE self-adhering membrane primer. * Requires approved TECHNICAL BINDER TTE I 3.25 - 3.27, SS 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 ** Only to be used in conjunction with APP Classic or APP Granular Cap. I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

INSULATION

COMMERCIAL INDUSTRIAL

ROOFING PRODUCTS

Drainage BINDER - 3.09 REFERENCE TECHNICAL 

3.28 - 3.29, 4.14.1, 6.14.1, 9.14.1 Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Temporary Closures - 4.19.1, 6.19.1, 9.19.1 Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

SE ANE A B R

M

EM

C

ER V O RD

BO

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

B

SU

A

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

COVER RETARDERS BOARD VAPOR INSULATION

G IN INGG SHIN LLAASSHH NG ASHI FLA PPF A F CCAPFL CAP E CA AANNEE N BBRRAN RA E EEMMBR M M P ME B CCAAPPMMEM CAP G CA HIN INGG IN ASSHH ING FFLLAASH E L S S EF A BBAASSEFL BASE NEE BA E RAANN AE MB BRR AN BR MME EMM B E E SSEMEM A E BBAS M BASE BA D ARRD BOA D RBOOAR E R B V OVER CCOVE CO N IO ATIONN ULATIO INS ULLAT S S IN U ERRS INS RDDE TAAR RS RREETRDE R A POOR ET VVAAP R R PO A V

(CHOOSE ONE)

COMMERCIAL & INDUSTRIAL

IKO MVP * - Is a self-adhering vapor membrane. It is composed of PROTECTOBOARD - Is composed of aretardant mineral-fortified asphaltic core between IKOTHERM - Isglass a rigid polyisocyanurate with highasthermal properties. It is STEEL modified rubber asphalt with a top surfaceinsulation film may of high cross laminated two non-woven fiber mats. Protectoboard be density used a cover board constructed from a closed cell polyisocyanurate foam core bonded on each side to glass polyethylene. This product should not be applied at temperatures below -10°C. over IKOTherm insulation, as a re-cover board in a re-roof installation, or any fiber reinforced the manufacturing process. other applicationfacers whereduring it is used as a new substrate for a modified bitumen or STEEL DECK STEEL DECKS - Must be a minimum of 22 gauge, manufactured milled steel ARMOURGARD VAPOR RETARDANT ** - Composed of twofrom layers of kraft BUR roofing membrane. NOTE: IKOTherm III withor acrylic-coated andof IKOTherm psi are also available. and bebonded factory primed galvanized to resist rusting. paper together with asphalt. facers Strands fiberglass25reinforcement are Modified Bitumen Heat Weld First layer must be mechanically attached or cold-applied with approved ahesive by IKO, intertwined near each edge for added strength and tear resistance. NOTE: Can be mechanically attached, cold applied or hot mopped. TECHNICAL BINDER unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, cold applied or I Steel - 3.11 hot mopped. Refer to IKO REFERENCE Commercial Binder for fastening patterns. * Self-adhering membrane may require Technical self-adhering primer. TECHNICAL BINDER I Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1 ** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive. Accessories, & Additional Considerations I 3.25 - 3.27,BINDER 4.11.1,Options 4.12.1, 6.11.1, 6.12.1 TECHNICAL REFERENCE L EEEL SSTTEEEL TECHNICAL BINDER I 3.25 - 3.27, ST 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

ROOFING PRODUCTS

Drainage - 3.09

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

C

ER V O RD

BO

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

SU

A

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

VAPOR RETARDERS INSULATION

INGG IN SHH ASH ING LAS FLA F P APFL CCAP CA NEE RAANE BBRAN EMM BR MEM M P E APM CCAP CA INGG SHHING LAASHIN EFLFLAS S E AS F BBASE BA NEE AANE BRR AN BR EMM B M E EM M ASSEME BBASE BA D ARRD BOA D RBOOAR E R B V OVER CCOVE CO

(CHOOSE ONE)

COMMERCIAL & INDUSTRIAL

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of IKOTHERM - Is asphalt a rigid with polyisocyanurate withdensity high thermal properties. It is STEEL modified rubber a top surfaceinsulation film of high cross laminated constructed from closed cell polyisocyanurate core bonded on each side to glass polyethylene. Thisaproduct should not be appliedfoam at temperatures below -10°C. fiber reinforced facers during the manufacturing process. STEEL DECK STEEL DECKS - Must be a minimum of 22 gauge, manufactured milled steel ARMOURGARD VAPOR RETARDANT ** - Composed of twofrom layers of kraft NOTE: IKOTherm III withor acrylic-coated andof IKOTherm psi are also available. and bebonded factory primed galvanized to resist rusting. paper together with asphalt. facers Strands fiberglass25reinforcement are Modified Bitumen Heat Weld IONN First layer must be each mechanically attached cold-applied ahesive by IKO, ATIO intertwined near edge for addedorstrength and with tear approved resistance. ULLAT INSU TECHNICAL BINDER RS unless a thermal barrier isREFERENCE used. Subsequent layers can be mechanically attached, cold applied or INS DES ARER I Steel - 3.11 EATRD mopped. Refer to IKO Commercial Binder for fastening patterns. RT *hotSelf-adhering membrane may require Technical self-adhering primer. RE R PO I Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1 AO R VP ** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive. VA Accessories, Options & Additional Considerations TECHNICAL BINDER REFERENCE ELL TEEE TECHNICAL BINDER I 3.25 - 3.27, SST 4.11.1, REFERENCE 4.12.1, 6.11.1, 6.12.1 I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE

ROOFING PRODUCTS

Drainage - 3.09

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

IN

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

SU

TIO LA

N

R PO ERS A V RD TA RE E ST

EL

VAPOR RETARDERS

INGG SHIN LASH PFFLA A CP CA E ANE BRAN EMMBR M E PM CAP CA INGG HN ASHI FLLAS E S F BASE BA NE RANE MBBRA MEEM E S M BASE BA

(CHOOSE ONE)

COMMERCIAL & INDUSTRIAL

IKO MVP * - Is a self-adhering vapor retardant membrane. It is composed of STEEL modified rubber asphalt with a top surface film of high density cross laminated polyethylene. This product should not be applied at temperatures below -10°C.

ROOFING PRODUCTS

STEEL DECKS - Must be a minimum of 22 gauge, manufactured milled steel ARMOURGARD VAPOR RETARDANT ** - Composed of twofrom layers of kraft and bebonded factory together primed or galvanized to resist of rusting. paper with asphalt. Strands fiberglass reinforcement Modified are intertwined near each edge for added strength and tear resistance. TECHNICAL BINDER REFERENCE I Steel - 3.11 * Self-adhering membrane may require self-adhering primer. I Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1 ** ArmourGard Vapor Retardant is adhered with ArmourGard Vapor Retardant Adhesive. Accessories, Options & Additional Considerations

D ARD BOAR RBO VEER O CV CO

STEEL DECK Bitumen Heat Weld

N IO ATION ULLAT INSSU N I

R PO VA EE ST

TECHNICAL BINDER REFERENCE I 3.22, 4.081, 6.08.1, 9.08.1 TECHNICAL BINDER REFERENCE Drainage - 3.09

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

R PO ERS A V RD TA RE E ST

EL

L

E RD TA RE

RS

ING SH LA PF A C E AN BR EM M P CA G HIN AS FL E S BA

COMMERCIAL & INDUSTRIAL

NE RA MB E EM

ROOFING PRODUCTS

STEEL

S BA

STEEL DECK STEEL DECKS - Must be a minimum of 22 gauge, manufactured from milled steel and be factory primed or galvanized to resist rusting. Modified Bitumen Heat Weld VE CO

R

D AR BO

N IO AT UL S N I

TECHNICAL BINDER REFERENCE I Steel - 3.11 I Roof Decks Re-Cover - 3.20, 4.07.1, 6.07.1, 9.07.1

R PO VA

Accessories, Options & Additional Considerations TECHNICAL BINDER REFERENCE

Drainage - 3.09

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

E ST

EL

E RD TA RE

RS

COMMERCIAL & INDUSTRIAL ROOFING PRODUCTS STEEL DECK Modified Bitumen Heat Weld Accessories, Options & Additional Considerations TECHNICAL BINDER REFERENCE Drainage - 3.09

Temporary Closures - 4.19.1, 6.19.1, 9.19.1

Asphalt - 3.23, 4.09.1, 6.9.1, 9.09.1

Sheet Metal - 3.38, 4.18.1, 6.18.1, 9.18.1

Cant Strips - 3.33, 4.13.1, 6.13.1, 9.13.1

Roof Walkways - 3.35, 4.21.1, 6.21.1

Wood Nailers - 3.24, 4.10.1, 6.10.1, 9.10.1

Cap Sheet Repair - 4.20.1, 6.20.1

Expansion Joints - 3.21 NOTE: Use of the above may or may not be applicable to your specific roof.

A properly designed and constructed roof deck, as well as the proper interrelationship of all building components are the responsibility of the architect, engineer and/or building owner. The density, moisture, integrity and other inherent elements of the deck must also be suitable to receive the roof. IKO is not responsible for any of the previously mentioned and IKO shall not assume responsibility for these issues under any circumstances.

PREMIUM QUALITY COMMERCIAL ROOFING PRODUCTS

Thank you for considering IKO Premium Roofing products. For additional information on IKO’s full line of superior Commercial/Indudtrial Roofing and Waterproofing products Please call: 1-800-361-5836, or visit our web site at:

Notes: The physical properties of the products described in this catalogue represent average typical results obtained by testing our products according to accepted industry test methods. These values are subject to normal manufacturing variations, and are supplied as a technical guideline only; they may be subject to change without notice. Current product specifications can be confirmed by contacting your local IKO technical Representative. Also, the guide specifications contained herein are offered as general information for the design and installation of IKO roof assemblies. IKO Industries Limited is a supplier of materials, and we cannot assume liability for errors in roof design, engineering, or application. The architect, contractor, and/or building owner’s representative must verify all dimensions, details and suitability of roof design. Notes: All values shown are approximate. Product and color availability subject to shipping area. The information in this document is subject to change without notice. IKO assumes no responsibility for errors that may appear in this document.

©

Copyright 07/07 - MM3L176 - STEEL DECK MODIFIED BITUMEN HEAT WELD - BK. 2