CH-CC June 2009 Replaces CH-CC, 04/07
REFRIGERATION PRODUCTS Condensed Catalog
www.chandlerref.com
Table of Contents Reach-In Unit Coolers
Condensing Units
Model TA Thin Profile Air Defrost....................................................3
Model CH 1/2-5 HP Hermetic Indoor/Outdoor...................... 16
Model TL Thin Profile Electric Defrost...........................................3
Model CZ 2-6 HP Scroll® Indoor/Outdoor................................ 17
Model C High Profile Air Defrost.....................................................3
Model CS 1/2-5 HP Semi-Hermetic Indoor/Outdoor............ 17
Model VA V-Profile Air Defrost.........................................................4
Models HDT, HDN, HDS 3-22 HP Discus® Indoor/Outdoor.18
Models BBM, BBL Back Bar................................................................4
Models HZT, HZN, HZS 3-22 HP Scroll® Indoor/Outdoor.... 18
Model KMK Standard Mullion..........................................................4
Model HDH 20-40 HP Discus® Outdoor..................................... 19
Model RAMK Reverse Air Mullion...................................................5
Model HDD 24-80 HP Dual Compressor Outdoor................. 20
Model BTO Twin Flow.........................................................................5
Model HWN 1/2-6 HP Hermetic Indoor Water-Cooled........ 21
Model U Dual Aire®..............................................................................5
Model ZWN 1/2-6 HP Scroll® Indoor Water-Cooled............... 21
Models LTA, LTL Extened Thin Profile Unit Cooler.....................6
Model SWN 3/4-20 HP Indoor Water-Cooled.......................... 22 Model SRN 3/4-20 HP Remote Indoor....................................... 23
Walk-In Unit Coolers Model RLC Low Profile Air Defrost.................................................6
Air-Cooled Condensers
Models ELC, EFC Low Profile Electric Defrost.............................7
Model WSS 1-26 Tons....................................................................... 24
Model GLC Low Profile Hot Gas Defrost.......................................7
Model HNE EC Series........................................................................ 25
Model LAH Low Flow Low Velocity Air Defrost..........................8
Models HNQ, HNX 830/540 Series............................................... 26
Model LAL Low Flow Low Velocity Electric Defrost.................8
Models HNL, HNH 830/540 Series............................................... 27
Model LAG Low Flow Low Velocity Hot Gas Defrost...............8 Model HWA Low Velocity Center Mount Air Defrost...............9 Model HWE Low Velocity Center Mount Electric Defrost......9 Model HWG Low Velocity Center Mount Hot Gas Defrost....9
Fluid Coolers Model WGS Direct-Drive...................................................................28 Model HFS Direct-Drive.....................................................................28
Model TLH Center Mount Air Defrost......................................... 10
Refrigeration Controls and Technology
Model TLL Center Mount Electric Defrost................................ 10
Beacon II™ Electronic Control Board.......................................... 29
Model HMA Medium Profile Air Defrost.................................... 10
Beacon II™ Smart Controller.......................................................... 29
Models HME, HML Medium Profile Electric Defrost.............. 11
Beacon II™ Smart Defrost............................................................... 29
Models HMG, HMF Medium Profile Hot Gas Defrost............ 11
Beacon II™ Smart Software............................................................ 29 Smart Defrost Kit™............................................................................ 29
Warehouse Unit Coolers Model HHA High Profile Air Defrost........................................... 12
Additional Products from Chandler
Models HHE, HHL High Profile Electric Defrost...................... 12
Mohave™ Hot Gas Defrost ............................................................ 30
Models HHG, HHF High Profile Hot Gas Defrost.................... 13
FlexPack™ ............................................................................................ 30
Packaged Refrigeration Systems
Engineered Solutions
Models PTT, PTN PRO3 Top Mount ............................................. 14
Air Handlers . ...................................................................................... 31
Model PST PRO3 Side Mount ........................................................ 15
Indoor and Outdoor Racks ........................................................... 31 Customer Specific Orders . ............................................................ 31
E Solutions™ branded products and options are designed to exceed current energy and environmental standards. We have made a conscious commitment to developing environmentally innovative products that allow our customers to make energy efficient, eco-conscious choices. Products included in the E Solutions portfolio reduce costs, improve bottom lines, and enhance both equipment performance and service life. Look for this mark throughout the catalog for products with features and options available to reduce energy consumption and environmental impact. Visit www.heatcraftrpd.com/esolutions for more information. © 2009 Heatcraft Refrigeration Products, LLC
2
Reach-In Unit Coolers Thin Profile Air Defrost Unit Coolers Model TA reach-in evaporators are thin units that mount in the top of a refrigerator, making the entire top shelf area
usable. The attractive low silhouette makes this unit particularly desirable for display-type refrigerators. It can also be used in back bars, under counter cabinets or wherever space is at a premium. Drain fitting at 45° angle so drain can be run through the back or bottom of refrigerator. Room for expansion valve inside so that it is out of sight. Model TA is available with optional coated coil for corrosion protection (use model designation TAK). Also features sweat inlet connection to reduce leaks.
TA (K) Model TA10 TA13 TA17 TA23 TA30 TA43* TA55*
Capacity (BTUH)
Fan
10°F TD +25 SST
Qty.
CFM
1,000 1,300 1,700 2,300 3,000 4,300 5,500
1 2 2 3 3 4 5
120 170 210 330 360 540 650
Motor (Total FLA) Shaded Pole 208115/1/60 230/1/60 0.8 0.4 1.6 0.8 1.6 0.8 2.4 1.2 2.4 1.2 3.2 1.6 4.0 2.0
Dimensions (in.)
Connections (in.)
L
H
D
Liquid OD
16-1/2 20-1/2 24 31-5/8 40 53-3/8 53-3/8
4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 6-3/4
13-1/2 13-1/2 14-1/2 14-1/2 14-1/2 14-1/2 14-1/2
3/8 3/8 3/8 3/8 3/8 1/2 1/2
Suction ID
Drain OD
3/8 3/8 3/8 3/8 1/2 5/8 5/8
1/2 1/2 1/2 1/2 1/2 1/2 1/2
Approx. Net Wt. (lbs.) 10 13 17 23 26 36 45
* These models use external equalized expansion valve
Thin Profile Electric Defrost Unit Coolers Model TL low temperature reach-in evaporators have an automatic defrost system. Mounted in the top of a refrigerator, its extremely compact cabinet makes it possible to utilize the entire top shelf area for storage. With a normal operating range of 15°F to –20°F, This unit is ideally suited for such applications as commercial freezers, ice cream boxes, bakery freezers and dual-temp reach-in boxes. Mechanical contact is provided between the heater elements and the drain pan, ensuring a warm pan during the defrost cycle. Sufficient space is provided to mount the expansion valve within the cabinet. Systems for both 115 volt and 208-230 volt operation are available. Also features sweat inlet connection to reduce leaks. Some models available with EC motors, contact your sales representative for availability.
TL Model
Capacity (BTUH)
Fan
Motor (Total FLA)
Shaded Pole 10°F TD Qty. CFM 208-10°F SST 115/1/60 230/1/60 TL09 900 1 110 0.8 0.4 TL12 1,200 2 210 1.6 0.8 TL16 1,600 2 210 1.6 0.8 TL21 2,100 1 240 1.0 0.5 TL28 2,800 3 335 1.2 TL35* 3,500 2 420 1.0 TL53* 5,300 3 595 1.5 * These models use external equalized expansion valve
Defrost Heater
Dimensions (in.)
115/1/60 230/1/60 Watts 475 600 700 1,100 1,430 1,600 1,950
Amps
Amps
4.1 5.2 6.1 9.6 -
2.1 2.6 3.0 4.8 5.7 7.0 8.5
Connections (in.)
L
H
D
Liquid OD
Suction ID
Drain OD
16-1/2 20-1/2 24 24 31-5/8 38-3/8 49-1/8
4-1/2 4-1/2 4-1/2 6-3/4 6-3/4 6-3/4 6-3/4
13-1/2 13-1/2 14-1/2 16-1/2 14-1/2 16-1/2 16-1/2
3/8 3/8 3/8 3/8 3/8 1/2 1/2
3/8 1/2 1/2 1/2 1/2 5/8 7/8
1/2 1/2 1/2 1/2 1/2 1/2 1/2
Approx. Net Wt. (lbs.) 10 15 19 19 22 31 45
High Profile Air Defrost Unit Coolers Model C unit coolers are ideal for refrigerated reach-ins. It mounts to the top of the refrigerator and discharges cold
air against the back wall. With this air flow pattern, the air is not blasted on the product, but is diffused along the back wall and then gently drawn across the product as it returns to the unit; thus, uniform temperatures are maintained throughout the refrigerator. In addition, door sweating and refrigeration loss due to door opening is greatly reduced because the air is not discharged against the doors. Mounting is easy with aluminum hangers that automatically space the unit the correct distance from the back wall. The expansion valve fits inside, out of sight. Model C is available with an optional coated coil (designated as model CK) for corrosion protection. Also features sweat inlet connection to reduce leaks. Some models available with EC motors, contact your sales representative for availability.
C (K) Model
Capacity (BTUH)
Fan
Motor (Total FLA)
Shaded Pole Qty. CFM 208115/1/60 230/1/60 C13 1,300 1 235 1.0 0.5 C17 1,700 1 250 1.0 0.5 C23 2,300 1 265 1.0 0.5 C30 3,000 2 480 2.0 1.0 C43* 4,300 2 520 2.0 1.0 * Size 43 uses external equalized expansion valve 10°F TD +25 SST
Dimensions (in.)
Connections (in.)
L
H
D
Liquid OD
14-1/4 17-1/4 22-3/4 27-3/4 38
8-7/8 8-7/8 8-7/8 8-7/8 8-7/8
13-3/4 13-3/4 13-3/4 13-3/4 13-3/4
3/8 3/8 3/8 3/8 1/2
Suction ID
Drain OD
3/8 1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2 1/2
Approx. Net Wt. (lbs.) 12 12 17 21 33
3
Reach-In Unit Coolers V-Profile Air Defrost Unit Coolers Model VA
reach-in evaporators are deluxe units designed for use in small reach-ins, back bar and under counter refrigerators, and many other applications where a small, compact unit is required. The thermal expansion valve mounts inside of the unit. The unit can be mounted from the ceiling or off the back or end walls, or can be used in mullion application. VA is available with an optional coated coil for corrosion protection (use model designation VAK). Also features sweat inlet connection to reduce leaks. Some models available with EC motors, contact your sales representative for availability.
VA (K) Model VA06 VA08 VA12 VA17
Capacity (BTUH)
Fan
Motor (Total FLA)
10°F TD +25 SST
Qty.
CFM
600 800 1,200 1,700
1 1 2 1
135 130 265 245
Dimensions (in.)
Shaded Pole 208115/1/60 230/1/60 0.8 0.4 0.8 0.4 1.6 0.8 1.0 0.5
Connections (in.)
L
H
D
Liquid OD
12-1/2 12-1/4 18 14
6-7/8 6-7/8 8 9-3/4
8-1/8 8-1/8 8-1/8 10-1/2
3/8 3/8 3/8 3/8
Suction ID
Drain OD
3/8 3/8 3/8 3/8
1/2 1/2 1/2 1/2
Approx. Net Wt. (lbs.) 7 7 12 9
Back Bar Unit Coolers Models BBM/BBL back bar unit coolers are available in either air or electric defrost. These compact,
wall-mounted units are suitable for 35°F to 40°F (BBM medium temp. models) and 0°F to -10°F (BBL low temp. models) under-counter reach-in fixtures. Motors are thermally protected and lifetime lubricated. Fan blades and guards are molded from corrosion-proof Lexan®. Housing is made of grained aluminum for long life and easy cleaning. Also features sweat inlet connection to reduce leaks. Capacity (BTUH) BB Model
BBL10 BBM11 BBL15 BBM16
Fan
Motor (Total FLA)
10°F TD +25 SST
Qty.
CFM
HP
1,000 1,100 1,500 1,600
1 1 2 2
90 90 180 180
1/150 1/150 1/150 1/150
Heater
Shaded Pole 115/1/60 0.8 0.8 1.6 1.6
208230/1/60 0.4 0.4 0.8 0.8
Watts 275 350 -
Dimensions (in.)
115/1/60
208230/1/60
Amps
Amps
2.7 3.5 -
1.4 1.7 -
Connections (in.)
L
H
D
Liquid OD
19-3/4 19-3/4 26-1/4 26-1/4
14 14 14 14
5-1/2 5-1/2 5-1/2 5-1/2
1/2 1/2 1/2 1/2
Standard Mullion Unit Coolers Model KMK
standard mullion unit coolers are ideal for use in under-counter reach-in refrigeration. The thin-line design allows the unit to be mounted behind a mullion with sufficient clearance for the installation of tray slides. KMK has a unique fan arrangement that allows air to be drawn into the top of the unit, pulling return air from both sides of the mullion. This arrangement allows the coldest air to be in contact with drop-in trays. The versatile design of these compact mullions is also adaptable for mounting on the back wall or ends of a beverage cooler. The finned coil of KMK is protected by special coating as standard. Also features sweat inlet connection to reduce leaks.
KMK Model KMK13 KMK17 KMK23
4
Capacity (BTUH)
Fan
10°F TD +25 SST
Qty.
CFM
1,300 1,700 2,300
2 2 3
180 170 255
Motor (Total FLA) Shaded Pole 208115/1/60 230/1/60 1.6 0.8 1.6 0.8 2.4 1.2
Dimensions (in.) L
H
15-5/8 17-3/4 15-5/8 19-3/4 22 19-3/4
Connections (in.)
D
Liquid OD
Suction ID
Drain OD
5-5/8 5-5/8 5-5/8
3/8 3/8 3/8
3/8 3/8 1/2
5/8 5/8 5/8
Approx. Net Wt. (lbs.) 15 17 23
Suction ID
Drain OD
3/8 3/8 3/8 3/8
1/2 1/2 1/2 1/2
Approx. Net Wt. (lbs.) 13 12 15 14
Reach-In Unit Coolers Reverse Air Mullion Unit Coolers Model RAMK reverse air mullion unit coolers are ideal for use in under-counter reach-in refrigeration. The thin-line design allows the unit to be mounted behind a mullion with sufficient clearance for the installation of tray slides. RAMK or Reverse Air Mullion draws air through the coil at the bottom and discharges the cooled air out the top. This arrangement allows the coldest air to be in contact with drop-in trays. The versatile design of these compact reverse air mullions is also adaptable for mounting on the back wall or ends of a beverage cooler. The finned coil of RAMK is protected by special coating as standard. Also features sweat inlet connection to reduce leaks.
RAMK Model RAMK13 RAMK17 RAMK23
Capacity (BTUH)
Fan
10°F TD +25 SST
Qty.
CFM
1,300 1,700 2,300
2 2 3
180 170 255
Motor (Total FLA) Shaded Pole 208115/1/60 230/1/60 1.6 0.8 1.6 0.8 2.4 1.2
Dimensions (in.) L
D
Liquid OD
Suction ID
Drain OD
5-5/8 5-5/8 5-5/8
3/8 3/8 3/8
3/8 3/8 1/2
5/8 5/8 5/8
H
15-5/8 17-3/4 15-5/8 19-3/4 22 19-3/4
Connections (in.)
Approx. Net Wt. (lbs.) 15 17 23
Twin-Flow Unit Coolers Model BTO twin-flow unit cooler is a compact design with medium velocity airflow. The unit is mounted flush to the ceiling and draws air in through the fan and discharges out both sides. The air pattern reduces air loss when doors are opened and the medium velocity reduces product drying. Twin-flow units are for applications of 35˚F and higher. Box temperatures are kept more constant throughout and fresh products last longer. Seven sizes are available with BTUH from 900 to 5,500 at 10˚TD. The BTO is available with an optional coated coil for corrosion protection (use model designation BTOK). Also features sweat inlet connection to reduce leaks.Some models available with EC motors, contact your sales representative for availability.
BTO (K) Model BTO09 BTO13 BTO18 BTO25* BTO35* BTO45* BTO55*
Capacity (BTUH)
Fan
10°F TD +25 SST
Qty.
CFM
900 1,300 1,800 2,500 3,500 4,500 5,500
1 2 1 2 2 2 1
130 240 255 460 425 550 730
Motor (Total FLA) Shaded Pole 208115/1/60 230/1/60 0.8 0.4 1.6 0.8 1.0 0.5 2.0 1.0 2.0 1.0 2.0 1.0 2.1 1.1
Dimensions (in.)
Connections (in.)
L
H
D
Inlet OD
19-1/8 19-1/8 19-1/8 26-1/8 26-1/8 29-1/8 29-1/8
4-7/8 5-3/4 5-3/4 6-3/4 6-3/4 9-1/4 8-1/2
16-1/8 16-1/8 16-1/8 18-1/8 18-1/8 21-1/8 21-1/8
1/2 1/2 1/2 1/2 1/2 1/2 1/2
Suction ID
Drain OD
1/2 1/2 1/2 1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2 1/2 5/8 5/8
Approx. Net Wt. (lbs.) 9 11 12 19 20 29 29
* These models use external equalized expansion valves
Dual Air Unit Coolers Model U unit cooler is used wherever a small, compact unit is required, such as salad boxes, back bars
and direct-draw boxes. It can be mounted on the ceiling or wall. The Model U unit draws air in through the front and discharges it out both sides to ensure proper distribution of cool air and maintain a uniform box temperature. Also features flare connections. U is available with an optional coated coil for corrosion protection (use model designation UK).
U (K) Model U09 U12 U15
Capacity (BTUH) 10°F TD +25 SST 850 1,150 1,500
Fan Qty. CFM 1 1 1
190 250 310
Motor (Total FLA) Shaded Pole 208115/1/60 230/1/60 0.45 0.55 0.45 0.55 1.10 0.55
Dimensions (in.)
Connections (in.)
L
H
D
Liquid FN
Suction ID
Drain OD
11-1/2 17-1/2 17-1/2
8-1/2 8-1/2 9-1/2
8-7/8 8-7/8 10-7/8
1/2 1/2 1/2
3/8 3/8 3/8
1/2 1/2 1/2
Approx. Net Wt. (lbs.) 8 8 12
5
Reach-In Unit Coolers Extended Thin Profile Unit Cooler Models LTA, LTL unit coolers are the most compact designed unit for reach-in display
cases. The unit’s low height design allows the unit to ‘hide’ at the top of the cooler, giving the case a cleaner look and allows for more room for shelves and product. These units have front-access end panels for easy access to refrigerant and electrical compartments, along with modular front-access panels that make it easy to access the motors. Internally enhanced tube design provides increased unit performance. Better performance, easy installation, servicing and the quality of Chandler makes this unit the perfect fit for your display case needs. Capacity (BTUH)
LTA Model
Fan
Motor (Total FLA)
10°F TD* Qty. CFM
HP
LTA053 LTA079 LTA102 LTA134 LTA172
5,300 7,900 10,200 13,400 17,200
2 3 4 5 6
850 1,350 1,800 2,250 2,550
1/20 1/20 1/20 1/20 1/20
LTL046BA LTL068BA LTL093BA LTL115BA LTL133BA
4,600 6,800 9,300 11,500 13,300
2 3 4 5 6
850 1,300 1,700 2,100 2,550
1/20 1/20 1/20 1/20 1/20
Defrost Heater
Dimensions (in.)
Shaded Pole 208-230/1/60 L 208115/1/60 Watts Amps 230/1/60 LTA Air Defrost 3.6 2.0 – – 49-3/8 5.4 3.0 – – 69-1/8 7.2 4.0 – – 88-7/8 9.0 5.0 – – 108-5/8 10.8 6.0 – – 128-3/8 LTL Electric Defrost – 2.0 1,100 4.8 49.50 – 3.0 1,650 7.2 69.25 – 4.0 2,200 9.6 89.00 – 5.0 2,750 12.0 108.75 – 6.0 3,300 14.4 128.50
Connections (in.)
Approx. Net Wt. Coil External Suction Drain (lbs.) Inlet Equalizer ID MPT OD OD
H
D
8-7/8 8-7/8 8-7/8 8-7/8 8-7/8
18-1/8 18-1/8 18-1/8 18-1/8 18-1/8
1/2 1/2 1/2 1/2 1/2
5/8 5/8 7/8 7/8 1-1/8
1/4 1/4 1/4 1/4 1/4
3/4 3/4 3/4 3/4 3/4
48 69 85 108 124
8-7/8 8-7/8 8-7/8 8-7/8 8-7/8
18-1/8 18-1/8 18-1/8 18-1/8 18-1/8
1/2 1/2 1/2 1/2 1/2
5/8 5/8 7/8 7/8 1-1/8
1/4 1/4 1/4 1/4 1/4
3/4 3/4 3/4 3/4 3/4
48 69 85 108 124
*+25 SST Air, -10 SST Electric
Walk-In Unit Coolers Low Profile Air Defrost Unit Coolers Model RLC low profile, air defrost unit coolers are designed for maximum capacity with
minimum headroom, space and energy. These units are suitable for use with R-22, R-507, or R404A. The units are only 15" high and are designed to mount flush with top of the cooler. The RLC cabinet design features easy front access to electrical and refrigeration components. RLC units also feature extended model and capacity offering to better match with Chandler condensing units. Advancements include standard plastic fan guard design with optional wire guards; front-facing electric board for easy access and optimized space in end panels. Improved drain pan design. Motor harness and solenoid harness are easier to access from the bottom of the coil. Solenoid harness come standard. Available with PSC and EC motor options.
RLC Model RLC040 RLC052 RLC065 RLC070 RLC090 RLC104 RLC120 RLC130 RLC140 RLC156 RLC180 RLC208 RLC260 RLC312 RLC370 1
Capacty (BTUH)
Fan
10°F TD +25 SST
Qty.
CFM
4,000 5,200 6,500 7,000 9,000 10,400 12,000 13,000 14,000 15,600 18,000 20,800 26,000 31,200 37,000
1 1 1 2 2 2 2 2 3 3 3 4 5 6 6
730 700 650 1,460 1,400 1,400 1,300 1,300 2,100 2,100 1,950 2,800 3,250 3,900 3,900
Motor (Total FLA)
Shaded Pole PSC, PSC-TE EC L 208208208115/1/60 115/1/60 460/1/60 115/1/60 230/1/60 230/1/60 230/1/60 1.8 1.0 1.0 0.5 0.4 0.9 0.5 29-1/2 1.8 1.0 1.0 0.5 0.4 0.9 0.5 29-1/2 1.8 1.0 1.0 0.5 0.4 0.9 0.5 29-1/2 3.6 2.0 2.0 1.0 0.8 1.8 1.0 45-1/2 3.6 2.0 2.0 1.0 0.8 1.8 1.0 45-1/2 3.6 2.0 2.0 1.0 0.8 1.8 1.0 45-1/2 3.6 2.0 2.0 1.0 0.8 1.8 1.0 45-1/2 3.6 2.0 2.0 1.0 0.8 1.8 1.0 45-1/2 5.4 3.0 3.0 1.5 1.2 2.7 1.5 61-1/2 5.4 3.0 3.0 1.5 1.2 2.7 1.5 61-1/2 5.4 3.0 3.0 1.5 1.2 2.7 1.5 61-1/2 7.2 4.0 4.0 2.0 1.6 3.6 2.0 77-1/2 9.0 5.0 5.0 2.5 2.0 4.5 2.5 93-1/2 10.8 6.0 6.0 3.0 2.4 5.4 3.0 109-1/2 10.8 6.0 6.0 3.0 2.4 5.4 3.0 109-1/2
Drain MPT 3/4" for all air defrost models
6
Dimensions1 (in.) Connections (in.) H
D
Inlet OD
15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
Suction ID 5/8 5/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-3/8
Approx. Net Wt. (lbs.) 28 31 34 45 48 49 51 53 63 67 69 82 103 124 127
Walk-In Unit Coolers Low Profile Electric Defrost Unit Coolers Models ELC/EFC low profile, electric defrost unit coolers offer the same features as the air defrost models above and are available in 6 or 4 fins per inch models.
Capacty Fan (BTUH) ELC/ EFC 10°F TD Model Qty. CFM -20 SST
Motor (Total FLA) Shaded Pole 208230/1/60
208230/1/60
PSC, PSC-TE
ELC035 ELC040 ELC047 ELC065 ELC075 ELC090 ELC120 ELC140 ELC160 ELC180 ELC200 ELC240 ELC280
3,500 4,000 4,700 6,500 7,500 9,000 12,000 14,000 16,000 18,000 20,000 24,000 28,000
1 1 1 2 2 2 3 3 4 4 5 6 6
700 700 650 1,400 1,300 1,300 2,100 1,950 2,600 2,600 3,250 3,900 3,900
1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 4.0 4.0 5.0 6.0 6.0
0.5 0.5 0.5 1.0 1.0 1.0 1.5 1.5 2.0 2.0 2.5 3.0 3.0
EFC041 EFC068 EFC080 EFC102 EFC136 EFC170 EFC204 EFC235
4,100 6,800 8,000 10,200 13,600 17,000 20,400 23,500
1 2 2 3 4 5 6 6
690 1,380 1,380 2,170 2,760 3,450 4,140 4,140
1.0 2.0 2.0 3.0 4.0 5.0 6.0 6.0
0.5 1.0 1.0 1.5 2.0 2.5 3.0 3.0
Defrost Heater (amps) Dimensions1 (in.) EC
208230/1 208230/1/60 ELC Models 6 Fins Per Inch 0.4 0.5 3.9 0.4 0.5 3.9 0.4 0.5 3.9 0.8 1.0 7.8 0.8 1.0 7.8 0.8 1.0 7.8 1.2 1.5 11.7 1.2 1.5 11.7 1.6 2.0 15.7 1.6 2.0 15.7 2.0 2.5 19.6 2.4 3.0 23.5 2.4 3.0 23.5 EFC Models 4 Fins Per Inch 0.4 0.5 3.9 0.8 1.0 7.8 0.8 1.0 7.8 1.2 1.5 11.7 1.6 2.0 15.7 2.0 2.5 19.6 2.4 3.0 23.5 2.4 3.0 23.5
460/1/60
Connections (in.)
Approx. Net Wt. Suction (lbs.) ID
208230/1
460/1
L
H
D
Inlet OD
2.3 2.3 2.3 4.5 4.5 4.5 6.8 6.8 9.0 9.0 11.3 13.6 13.6
2.0 2.0 2.0 3.9 3.9 3.9 5.9 5.9 7.8 7.8 9.8 11.7 11.7
29-1/2 29-1/2 29-1/2 45-1/2 45-1/2 45-1/2 61-1/2 61-1/2 77-1/2 77-1/2 93-1/2 109-1/2 109-1/2
15 15 15 15 15 15 15 15 15 15 15 15 15
15 15 15 15 15 15 15 15 15 15 15 15 15
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
5/8 5/8 5/8 5/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8
24 26 29 43 45 48 60 62 81 84 101 121 124
2.3 4.5 4.5 6.8 9.0 11.3 13.6 13.6
2.0 3.9 3.9 5.9 7.8 9.8 11.7 11.7
29-1/2 45-1/2 45-1/2 61-1/2 77-1/2 93-1/2 109-1/2 109-1/2
15 15 15 15 15 15 15 15
15 15 15 15 15 15 15 15
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
5/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8
28 44 47 59 80 100 120 123
Low Profile Hot Gas Defrost Unit Coolers Model GLC low profile, hot gas defrost unit coolers offer the same features as the air defrost models above and are available in 6 or 4 fins per inch models.
GLC Model
Capacty (BTUH) 10°F TD -20 SST
Fan
Motor (Total FLA) Shaded Pole
Qty. CFM
PSC, PSC-TE
208115/1/60 115/1/60 230/1/60
GLC035 GLC040 GLC047 GLC065 GLC075 GLC090 GLC120 GLC140 GLC160 GLC180 GLC200 GLC240 GLC280
3,500 4,000 4,700 6,500 7,500 9,000 12,000 14,000 16,000 18,000 20,000 24,000 28,000
1 1 1 2 2 2 3 3 4 4 5 6 6
700 700 650 1,400 1,300 1,300 2,100 1,950 2,600 2,600 3,250 3,900 3,900
1.8 1.8 1.8 3.6 3.6 3.6 5.4 5.4 7.2 7.2 9.0 10.8 10.8
1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 4.0 4.0 5.0 6.0 6.0
1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 4.0 4.0 5.0 6.0 6.0
GLC041 GLC068 GLC080 GLC102 GLC136 GLC170 GLC204 GLC235
4,100 6,800 8,000 10,200 13,600 17,000 20,400 23,500
1 2 2 3 4 5 6 6
690 1,380 1,380 2,170 2,760 3,450 4,140 4,140
1.8 3.6 3.6 5.4 7.2 9.0 10.8 10.8
1.0 2.0 2.0 3.0 4.0 5.0 6.0 6.0
1.0 2.0 2.0 3.0 4.0 5.0 6.0 6.0
Dimensions1 (in.) EC
208460/1/60 115/1/60 230/1/60 GLC Models 6 Fins Per Inch 0.5 0.4 1.1 0.5 0.4 1.1 0.5 0.4 1.1 1.0 0.8 2.0 1.0 0.8 2.0 1.0 0.8 2.0 1.5 1.2 2.9 1.5 1.2 2.9 2.0 1.6 3.8 2.0 1.6 3.8 2.5 2.0 4.7 3.0 2.4 5.6 3.0 2.4 5.6 GLC Models 4 Fins Per Inch 0.5 0.4 1.1 1.0 0.8 2.0 1.0 0.8 2.0 1.5 1.2 2.9 2.0 1.6 3.8 2.5 2.0 4.7 3.0 2.4 5.6 3.0 2.4 5.6
Drain MPT 3/4" for all electric and hot gas defrost models. Side Port OD 3/8" and Hot Gas Pan Connection 5/8" for all hot gas defrost models.
Connections (in.) Inlet
Approx.
Suction Net Wt. (lbs.) ID
208230/1/60
L
H
D
0.6 0.6 0.6 1.1 1.1 1.1 1.6 1.6 2.1 2.1 2.6 3.1 3.1
29-1/2 29-1/2 29-1/2 45-1/2 45-1/2 45-1/2 61-1/2 61-1/2 77-1/2 77-1/2 93-1/2 109-1/2 109-1/2
15 15 15 15 15 15 15 15 15 15 15 15 15
15 15 15 15 15 15 15 15 15 15 15 15 15
5/8 5/8 5/8 5/8 7/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8
5/8 5/8 5/8 5/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8
26 28 31 45 47 50 62 64 83 86 103 123 126
0.6 1.1 1.1 1.6 2.1 2.6 3.1 3.1
29-1/2 45-1/2 45-1/2 61-1/2 77-1/2 93-1/2 109-1/2 109-1/2
15 15 15 15 15 15 15 15
15 15 15 15 15 15 15 15
5/8 5/8 5/8 7/8 7/8 7/8 7/8 1-1/8
5/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8
30 46 49 61 82 102 122 125
ODF
1
7
Walk-In Unit Coolers Low Flow Low Velocity Air Defrost Unit Coolers Model LAH are ideal for meat storage and preparation rooms, floral coolers, dough retarding and many other applications requiring low air velocities and low sound levels. With low velocity unit coolers, high humidities can be maintained to minimize product shrinkage and dehydration. These units are ideal for any type of workroom where human comfort is important.
With a low, narrow construction and strong aluminum hanger bars, Low Flow Low Velocity is perfect for use in between rail beams in meat storage and aging rooms and is easy to install. Model LAH has been designed for the attractive appearance and easy cleaning necessary in food processing. A double drain pan system eliminates sweating problems, and the rust-free, all-aluminum white case ensures the long-lasting professional look needed in customer areas or work rooms. Available with PSC and EC motor options. LAH Model LAH070 LAH090 LAH120 LAH130 LAH160 LAH170 LAH190 LAH220 LAH270
Capacity (BTUH)* 10°F TD 7,000 8,700 11,800 12,500 15,000 16,500 18,900 22,500 26,600
Fan
15°F Qty. CFM TD 10,500 13,050 17,700 18,750 22,500 24,750 28,350 33,750 39,900
2 2 2 2 2 2 2 2 2
1,200 1,200 1,300 1,300 1,900 1,900 2,400 2,700 3,200
Motor (Total FLA) Dimensions (in.) Connections (in.) Approx. Shaded Pole PSC EC Net Wt. Liq. Suct. Drain (lbs.) L H D 208208208OD OD NPS 115/1/60 115/1/60 460/1/60 115/1/60 230/1/60 230/1/60 230/1/60 3.6 2.4 1.24 0.82 – 1.8 1.0 83 14 23-1/4 1/2 7/8 3/4 178 3.6 2.4 1.24 0.82 – 1.8 1.0 83 14 23-1/4 1/2 7/8 3/4 189 3.6 2.4 1.24 0.82 – 1.8 1.0 111 14-1/2 23-1/4 1/2 7/8 3/4 262 3.6 2.4 1.24 0.82 – 1.8 1.0 111 14-1/2 23-1/4 1/2 7/8 3/4 264 3.6 2.4 1.24 0.82 – 1.8 1.0 114 16 23-1/4 1/2 1-1/8 3/4 280 3.6 2.4 1.24 0.82 – 1.8 1.0 114 16 23-1/4 1/2 1-1/8 3/4 285 – – 2.80 1.40 0.8 4.8 2.4 134 16-1/2 23-1/4 1/2 1-1/8 3/4 298 – – 2.80 1.40 0.8 4.8 2.4 153 16-1/2 23-1/4 1/2 1-1/8 3/4 366 – – 2.80 1.40 0.8 4.8 2.4 158 20 28-1/4 1/2 1-3/8 3/4 405
Low Flow Low Velocity Electric Defrost Unit Coolers Model LAL offers the same features as air defrost models and are designed for use from 28°F to 34°F. The high efficiency, fast electric defrost allows the LAL to maintain room temperature and minimize incidence of sliming and the formation of bacterial growth. LAL Model LAL070 LAL090 LAL120 LAL130 LAL160 LAL170 LAL190 LAL220 LAL270
Capacity (BTUH)*
10°F TD 7,000 8,700 11,800 12,500 15,000 16,500 18,900 22,500 26,600
Fan
15°F Qty. CFM TD 10,500 13,050 17,700 18,750 22,500 24,750 28,350 33,750 39,900
2 2 2 2 2 2 2 2 2
1,200 1,200 1,300 1,300 1,900 1,900 2,400 2,700 3,200
Motor (Total FLA) Shaded Pole PSC EC 208208208460/1/60 230/1/60 230/1/60 230/1/60 2.4 0.82 – 1.0 2.4 0.82 – 1.0 2.4 0.82 – 1.0 2.4 0.82 – 1.0 2.4 0.82 – 1.0 2.4 0.82 – 1.0 – 1.40 0.8 4.8 – 1.40 0.8 4.8 – 1.40 0.8 4.8
Defrost Heater 230/1/60
Watts 2,650 2,650 3,850 3,850 3,850 3,850 4,770 5,700 5,700
Connections (in.)
Dimensions (in.)
Amps
L
H
D
11.5 11.5 16.7 16.7 16.7 16.7 20.7 24.8 24.8
83 83 111 111 114 114 134 153 158
14 14 14-1/2 14-1/2 16 16 16-1/2 16-1/2 20
23-1/4 23-1/4 23-1/4 23-1/4 23-1/4 23-1/4 23-1/4 23-1/4 28-1/4
Liq. OD 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
Suct. OD 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8
Approx. Net Wt. Drain (lbs.) NPS 3/4 178 3/4 189 3/4 262 3/4 264 3/4 280 3/4 285 3/4 298 3/4 366 3/4 405
Low Flow Low Velocity Hot Gas Defrost Unit Coolers Model LAG offers the same features as air defrost models and are designed for use from 28°F to 34°F. The hot gas defrost is available factory-installed or as a field installed kit. Capacity (BTUH)* LAG Model
LAG070 LAG090 LAG120 LAG130 LAG160 LAG170 LAG190 LAG220 LAG270
* +25 SST
8
10°F TD 7,000 8,700 11,800 12,500 15,000 16,500 18,900 22,500 26,600
Fan
15°F Qty. CFM TD 10,500 13,050 17,700 18,750 22,500 24,750 28,350 33,750 39,900
2 2 2 2 2 2 2 2 2
1,200 1,200 1,300 1,300 1,900 1,900 2,400 2,700 3,200
Motor (Total FLA) Shaded Pole 115/1/60 3.6 3.6 3.6 3.6 3.6 3.6 – – –
PSC
Dimensions (in.) EC
Connections (in.) Approx. Net Wt. Hot Liq. Suct. Drain (lbs.) Gas NPS OD OD OD
L H D 208208208115/1/60 460/1/60 115/1/60 230/1/60 230/1/60 230/1/60 2.4 1.24 1.0 – 1.8 1.0 83 14 23-1/4 7/8 7/8 2.4 1.24 1.0 – 1.8 1.0 83 14 23-1/4 7/8 7/8 2.4 1.24 1.0 – 1.8 1.0 111 14-1/2 23-1/4 7/8 7/8 2.4 1.24 1.0 – 1.8 1.0 111 14-1/2 23-1/4 7/8 7/8 2.4 1.24 1.0 – 1.8 1.0 114 16 23-1/4 7/8 1-1/8 2.4 1.24 1.0 – 1.8 1.0 114 16 23-1/4 7/8 1-1/8 – 2.80 1.4 .08 4.8 2.4 134 16-1/2 23-1/4 7/8 1-1/8 – 2.80 1.4 .08 4.8 2.4 153 16-1/2 23-1/4 7/8 1-1/8 – 2.80 1.4 .08 4.8 2.4 158 20 28-1/4 7/8 1-3/8
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8
3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4
178 189 262 264 280 285 298 366 405
Walk-In Unit Coolers Low Velocity Center Mount Air Defrost Unit Coolers Model HWA is ideal for floral storage, fresh fruit and vegetables, dough retarding, fresh meat storage and preparation and many other applications of 35° F and above. The low air flow and quiet fans are classically suited for work-room applications.
The generous coil surface combined with close TD system balance provides high humidity characteristics to minimize product shrinkage and drying. Available with PSC and EC motor options. HWA Model HWA050 HWA075 HWA100 HWA130 HWA155 HWA180 HWA210 HWA270 HWA340
Capacity Fan Motor (Total FLA) (BTUH)* Shaded Pole PSC EC 10°F 15°F Qty. CFM TD TD 115/1/60 230/1/60 115/1/60 230/1/60 115/1/60 230/1/60 5,000 7,500 1 725 2.1 1.1 0.9 0.5 0.9 0.5 7,500 11,250 1 730 2.1 1.1 0.9 0.5 0.9 0.5 10,000 15,000 2 1,450 4.2 2.2 1.8 1.0 1.8 1.0 13,000 19,500 2 1,470 4.2 2.2 1.8 1.0 1.8 1.0 15,500 23,250 2 1,460 4.2 2.2 1.8 1.0 1.8 1.0 18,000 27,000 3 2,130 6.3 3.3 2.7 1.5 2.7 1.5 21,000 31,500 4 2,840 8.4 4.4 3.6 2.0 3.6 2.0 27,000 40,500 4 2,800 8.4 4.4 3.6 2.0 3.6 2.0 34,000 51,000 5 3,500 10.5 5.5 4.5 2.5 4.5 2.5
App. Net Liquid Suction Drain Wt. L H D OD OD FPT (lbs.) 53-1/2 8-7/8 26-5/8 1/2 7/8 3/4 70 75-1/2 8-7/8 26-5/8 1/2 7/8 3/4 103 75-1/2 11-3/8 26-5/8 1/2 7/8 3/4 106 75-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 145 75-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 149 75-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 160 97-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 193 97-1/2 15-1/8 26-5/8 1-3/8 1-3/8 3/4 200 119-1/2 15-1/8 26-5/8 1-3/8 1-3/8 3/4 242 Dimensions (in.)
Connections (in.)
Low Velocity Center Mount Electric Defrost Unit Coolers Model HWE offers the same benefits as the air defrost models above and is ideal for applications of 24° F and above. HWE Model HWE050 HWE075 HWE100 HWE130 HWE155 HWE180 HWE210 HWE270 HWE340
Capacity Fan (BTUH)* 10°F 15°F Qty. CFM TD TD 5,000 7,500 1 725 7,500 11,250 1 730 10,000 15,000 2 1,450 13,000 19,500 2 1,470 15,500 23,250 2 1,460 18,000 27,000 3 2,130 21,000 31,500 4 2,840 27,000 40,500 4 2,800 34,000 51,000 5 3,500
Motor (Total FLA) Shaded Pole 230/1/60 1.1 1.1 2.2 2.2 2.2 3.3 4.4 4.4 5.5
PSC 230/1/60 0.5 0.5 1.0 1.0 1.0 1.5 2.0 2.0 2.5
App. Net 230/1/60 Liquid Suction Drain Wt. L H D OD OD FPT (lbs.) Amps 8.7 53-1/2 8-7/8 26-5/8 1/2 7/8 3/4 75 10.5 75-1/2 8-7/8 26-5/8 1/2 7/8 3/4 108 12.2 75-1/2 11-3/8 26-5/8 1/2 7/8 3/4 111 17.4 75-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 150 17.4 75-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 154 17.4 75-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 157 22.6 97-1/2 15-1/8 26-5/8 1-1/8 1-1/8 3/4 203 22.6 97-1/2 15-1/8 26-5/8 1-3/8 1-3/8 3/4 208 30.4 119-1/2 15-1/8 26-5/8 1-3/8 1-3/8 3/4 250
Defrost Heater EC 230/1/60 0.5 0.5 1.0 1.0 1.0 1.5 2.0 2.0 2.5
Watts 2,000 2,400 2,800 4,000 4,000 4,000 5,200 5,200 7,000
Dimensions (in.)
Connections (in.)
Low Velocity Center Mount Hot Gas Defrost Unit Coolers Model HWG offers the same benefits as the air defrost models above and is ideal for applications of 24° F and above.
HWG Model HWG100 HWG130 HWG155 HWG180 HWG210 HWG270 HWG340
Capacity (BTUH)* 10°F TD
15°F TD
10,000 13,000 15,500 18,000 21,000 27,000 34,000
15,000 19,500 23,250 27,000 31,500 40,500 51,000
Fan
Motor (Total FLA) Shaded Pole
Qty. CFM 2 2 2 3 4 4 5
1,450 1,470 1,460 2,130 2,840 2,800 3,500
2.2 2.2 2.2 3.3 4.4 4.4 5.5
1.8 1.8 1.8 2.7 3.6 3.6 4.5
EC 115/1 230/1 208208- Watts 115/1/60 Amps 230/1/60 230/1/60 1.0 1.8 1.0 350 3.0 1.5 1.0 1.8 1.0 500 4.4 2.2 1.0 1.8 1.0 500 4.4 2.2 1.5 2.7 1.5 500 4.4 2.2 2.0 3.6 2.0 650 5.7 2.8 2.0 3.6 2.0 650 5.7 2.8 2.5 4.5 2.5 875 7.6 3.8
Dimensions (in.)
PSC
115/1/60 230/1/60 115/1/60 4.2 4.2 4.2 6.3 8.4 8.4 10.5
Drain Pan Heater
L
H
D
75-1/2 75-1/2 75-1/2 75-1/2 97-1/2 97-1/2 119-1/2
11-3/8 15-1/8 15-1/8 15-1/8 15-1/8 15-1/8 15-1/8
26-5/8 26-5/8 26-5/8 26-5/8 26-5/8 26-5/8 26-5/8
Connections (in.)1 App. Net Liq. Suct. Side Wt. OD OD Port (lbs.) 1/2 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8
7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8
1/2 5/8 5/8 5/8 5/8 7/8 7/8
131 170 174 185 223 228 270
* +25 SST 1 Drain FPT 3/4" for all models
9
Walk-In Unit Coolers Center Mount Air Defrost Unit Coolers Model TLH units are compact, medium velocity coolers designed for use in 35° F and above
rooms. The low height gives more head room and allows product to be stacked higher. The center ceiling mount with dual air flow allows shelving and storage of product around all walls. Equipped with dual drain pans to prevent sweating, the TLH units have a heavy gauge grained-aluminum cabinet that cleans easily and looks attractive. The stainless steel screws prevent rust streaks and PVC coated fan guards won’t rust or rattle. Ease of installation and service are also part of the design. End panels can be removed quickly to access refrigerant components and electrical terminal block, without the need to drop the fan panel/drain pan. A quick-disconnect, waterproof plug and receptacle is supplied with each motor. Available with PSC and EC motor options. TLH Model TLH052 TLH076 TLH090 TLH102 TLH108 TLH134 TLH156 TLH179 TLH208 TLH249
Capacity (BTUH)
Fan
Motor (Total FLA) Shaded Pole
PSC
10°F TD Qty. CFM +25 SST 115/1/60 230/1/60 115/1/60 5,200 7,600 9,000 10,200 10,800 13,400 15,600 17,900 20,800 24,900
1 2 2 2 3 3 3 4 4 5
610 1,300 1,260 1,220 1,950 1,890 1,830 2,520 2,440 3,050
2.1 4.2 4.2 4.2 6.3 6.3 6.3 8.4 8.4 10.5
1.1 2.2 2.2 2.2 3.3 3.3 3.3 4.4 4.4 5.5
Dimensions (in.)
0.9 1.8 1.8 1.8 2.7 2.7 2.7 3.6 3.6 4.5
EC
L 208208115/1/60 230/1/60 230/1/60 0.5 0.9 0.5 31-1/2 1.0 1.8 1.0 53-1/2 1.0 1.8 1.0 53-1/2 1.0 1.8 1.0 53-1/2 1.5 2.7 1.5 75-1/2 1.5 2.7 1.5 75-1/2 1.5 2.7 1.5 75-1/2 2.0 3.6 2.0 97-1/2 2.0 3.6 2.0 97-1/2 2.5 4.5 2.5 119-1/2
Connections1 (in.)
H
D
Liquid OD
8-5/8 8-5/8 8-5/8 8-5/8 8-5/8 8-5/8 8-5/8 8-5/8 8-5/8 8-5/8
28-13/16 28-13/16 28-13/16 28-13/16 28-13/16 28-13/16 28-13/16 28-13/16 28-13/16 28-13/16
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
Approx. Net Wt. Suction (lbs.) OD 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8
42 64 70 83 105 117 123 149 164 206
Center Mount Electric Defrost Unit Coolers Model TLL units offer the same great benefits as air defrost, but have defrost controls mounted and wired to a terminal board and are designed for –20° F to 34° F applications.
Capacity (BTUH) Fan Motor (Total FLA) Shaded Pole PSC EC TLL 10°F TD 12°F Model Qty. CFM 208208-20 SST TD 208-230/1 230/1/60 230/1/60 TLL040 4,000 4,800 1 610 1.1 0.5 0.5 TLL054 5,400 6,480 2 1,300 2.2 1.0 1.0 TLL065 6,500 7,800 2 1,260 2.2 1.0 1.0 TLL090 9,000 10,800 3 1,950 3.3 1.5 1.5 TLL130 13,000 15,600 3 1,830 3.3 1.5 1.5 TLL174 17,400 20,880 4 2,440 4.4 2.0 2.0
Defrost Heater
Dimensions (in.)
Connections1 (in.)
Watts
Amps
L
H
D
Inlet OD
Suction OD
Approx. Net Wt. (lbs.)
1,200 2,000 2,000 2,400 3,600 4,800
5.3 8.7 8.7 10.5 15.7 20.9
31-1/2 53-1/2 53-1/2 75-1/2 75-1/2 97-1/2
8-5/8 8-5/8 8-5/8 8-5/8 8-5/8 8-5/8
28-13/16 28-13/16 28-13/16 28-13/16 28-13/16 28-13/16
1/2 1/2 1/2 1/2 1/2 1/2
7/8 7/8 7/8 7/8 7/8 1-1/8
90 120 120 160 174 218
Medium Profile Unit Coolers Models HMA engineered superior quality and performance into the new
medium profile unit coolers. With features like the innovative Thermo-Flex™ coil design that carries a five-year limited warranty against refrigerant leaks, internal grooved tubing for greater heat transfer efficiency and motors that plug into the wiring harness for easier accessibility, these units provide long life and dependability to your refrigeration application. Capacity Fan Motor (Total FLA) Dimensions (in.) Connections1 (in.) App. (BTUH) Net Wt. PSC EC 10°F TD Inlet Suct. (lbs.) Qty. CFM L H D +25 SST ODF ODF 115/1/60 230/1/60 460/1660 115/1/60 208-230/1/60 HMA130 13,000 1 2,300 4.0 1.8 1.0 2.8 1.4 39-5/16 25 22-7/8 1/2 7/8 115 HMA155 15,500 1 2,200 4.0 1.8 1.0 2.8 1.4 39-5/16 25 22-7/8 1/2 1-1/8 123 HMA245 24,500 2 4,600 8.0 3.6 2.0 5.6 2.8 67-5/16 25 22-7/8 7/8 1-1/8 134 HMA300 30,000 2 4,400 8.0 3.6 2.0 5.6 2.8 67-5/16 25 22-7/8 7/8 1-1/8 148 HMA365 36,500 3 6,900 12.0 5.4 3.0 8.4 4.2 95-5/16 25 22-7/8 7/8 1-3/8 200 HMA450 45,000 3 6,600 12.0 5.4 3.0 8.4 4.2 95-5/16 25 22-7/8 1-1/8† 1-3/8 227 HMA510 51,000 4 9,200 16.0 7.2 4.0 11.2 5.6 123-5/16 25 22-7/8 1-1/8† 1-5/8 230 HMA600 60,000 4 8,800 16.0 7.2 4.0 11.2 5.6 123-5/16 25 22-7/8 1-1/8† 1-5/8 255 HMA710 71,000 5 10,500 9.0 5.0 14.0 7.0 138-13/16 25 22-7/8 1-1/8† 1-5/8 285 1 All HMA coils have 1/4" OD external equalizer and 3/4" Drain FPT connections. † Supplied with adapter to 7/8 ODF. HMA Model
10
Walk-In Unit Coolers Medium Profile Electric Defrost Unit Coolers Models HME/HML offer the same great features as air defrost models and are available in 6 or 4 fins per inch ranging in size from 10,000 to 62,000 BTUH.
HME/ HML Model
HME101 HME140 HME190 HME260 HME310 HME390 HME430 HME520 HME620 HML100 HML165 HML220 HML250 HML330 HML370 HML440 HML530
Capacity (BTUH)
Fan
Motor (Total FLA)
Defrost Heater (amps)
PSC EC 10°F TD 208208Qty. CFM 208- 460/1/60 575/1/60 208230/3/60 -20 SST 230/1/60 230/1/60 Watts 230/1/60 HME Models 6 Fins Per Inch 10,100 1 2,350 1.8 1.0 0.75 1.4 2,730 11.9 8.2 14,000 1 2,250 1.8 1.0 0.75 1.4 2,730 11.9 8.2 19,000 2 4,700 3.6 2.0 1.50 2.8 5,350 23.3 16.0 26,000 2 4,500 3.6 2.0 1.50 2.8 5,350 23.3 16.0 31,000 3 7,050 5.4 3.0 2.25 4.2 7,750 33.7 23.2 39,000 3 6,750 5.4 3.0 2.25 4.2 7,750 33.7 23.2 43,000 4 8,800 7.2 4.0 3.00 5.6 10,200 – 30.5 52,000 4 8,400 7.2 4.0 3.00 5.6 10,200 – 30.5 62,000 5 10,000 9.0 5.0 3.75 7.0 11,600 – 34.7 HML Models 4 Fins Per Inch 10,000 1 2,350 1.8 1.0 0.75 1.4 2,730 11.9 8.2 16,500 2 4,900 3.6 2.0 0.75 2.8 5,350 23.3 16.0 22,000 2 4,650 3.6 2.0 1.50 2.8 5,350 23.3 16.0 25,000 3 7,350 5.4 3.0 1.50 4.2 7,750 33.7 23.2 33,000 3 6,975 5.5 3.0 2.25 4.2 7,750 33.7 23.2 37,000 4 9,100 7.2 4.0 2.25 5.6 10,200 – 30.5 44,000 4 8,700 7.2 4.0 3.00 5.6 10,200 – 30.5 53,000 5 10,350 9.0 5.0 3.00 7.0 11,600 – 34.7
Dimensions (in.)
Connections1 App. (in.) Net Inlet Suct. Wt. ODF ODF (lbs.)
460/ 1/60
460/ 3/60
L
H
D
5.9 5.9 11.6 11.6 16.8 16.8 22.2 22.2 25.2
4.1 4.1 8.3 8.3 12.0 12.0 15.8 15.8 18.1
39-5/16 39-5/16 67-5/16 67-5/16 95-5/16 95-5/16 123-5/16 123-5/16 138-5/16
24 24 24 24 24 24 24 24 24
22-3/4 22-3/4 22-3/4 22-3/4 22-3/4 22-3/4 22-3/4 22-3/4 22-3/4
1/2 1/2 7/8 1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8†
7/8 7/8 1-1/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8
118 126 138 153 210 237 267 300 338
5.9 11.6 11.6 16.8 16.8 22.2 22.2 25.2
4.1 39-13/16 24 22-3/4 8.3 67-13/16 24 22-3/4 8.3 67-13/16 24 22-3/4 12.0 95-13/16 24 22-3/4 12.0 95-13/16 24 22-3/4 15.8 123-13/16 24 22-3/4 15.8 123-13/16 24 22-3/4 18.1 138-13/16 24 22-3/4
1/2 7/8 1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8†
7/8 1-1/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8
125 136 151 207 234 262 295 332
Medium Profile Hot Gas Defrost Unit Coolers Models HMG/HMF offer the same great features as air defrost models and are available in 6 or 4 fins per inch ranging in size from 16,500 to 52,000 BTUH.
HMG/ HMF Model
Capacity (BTUH)
Fan
10°F TD Qty. CFM -20 SST
Motor (Total FLA) 115/ 1/60
PSC 230/ 460/ 1/60 1/60
575/ 1/60
HMG190 HMG260 HMG310 HMG390 HMG430 HMG520
19,000 26,000 31,000 39,000 43,000 52,000
2 2 3 3 4 4
4,700 4,500 7,050 6,750 8,800 8,400
8.0 8.0 12.0 12.0 16.0 16.0
3.6 3.6 5.4 5.4 7.2 7.2
2.0 2.0 3.0 3.0 4.0 4.0
0.75 0.75 1.50 1.50 2.25 2.25
HMF165 HMF220 HMF250 HMF330 HMF370 HMF440
16,500 22,000 25,000 33,000 37,000 44,000
2 2 3 3 4 4
4,900 4,650 7,350 6,975 9,100 8,700
8.0 8.0 12.0 12.0 16.0 16.0
3.6 3.6 5.4 5.4 7.2 7.2
2.0 2.0 3.0 3.0 4.0 4.0
0.75 0.75 1.50 1.50 2.25 2.25
Defrost Heater (amps)
Dimensions (in.)
EC 115/ 208460/ Watts L H 115/ 2081/60 230/1/60 1/60 1/60 230/1/60 HMG Models 6 Fins Per Inch 5.6 2.8 950 8.3 4.1 2.1 67-5/16 24 5.6 2.8 950 8.3 4.1 2.1 67-5/16 24 8.4 4.2 1,350 11.7 5.9 2.9 95-5/16 24 8.4 4.2 1,350 11.7 5.9 2.9 95-5/16 24 11.2 5.6 1,800 15.7 7.8 3.9 123-5/16 24 11.2 5.6 1,800 15.7 7.8 3.9 123-5/16 24 HMF Models 4 Fins Per Inch 5.6 2.8 950 8.3 4.1 2.1 67-13/16 24 5.6 2.8 950 8.3 4.1 2.1 67-13/16 24 8.4 4.2 1,350 11.7 5.9 2.9 95-13/16 24 8.4 4.2 1,350 11.7 5.9 2.9 95-13/16 24 11.2 5.6 1,800 15.7 7.8 3.9 123-13/16 24 11.2 5.6 1,800 15.7 7.8 3.9 123-13/16 24
D
Connections1 App. (in.) Net Inlet Suct. Wt. ODF ODF (lbs.)
22-3/4 22-3/4 22-3/4 22-3/4 22-3/4 22-3/4
1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8†
1-1/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8
175 190 210 237 267 300
22-3/4 22-3/4 22-3/4 22-3/4 22-3/4 22-3/4
1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8† 1-1/8†
1-1/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8
173 188 207 234 262 295
All HME, HML, HMG and HMF models have 1/4" OD external equalizer and 3/4" Drain FPT connections. All HMG and HMF models have 5/8" Side Port ODF and 7/8" Hot Gas Pan ODF connections. 1
†
Supplied with adapter to 7/8 ODF
11
Warehouse Unit Coolers Large Unit Coolers Air Defrost Model HHA large air defrost unit coolers are ideal for warehouse cooler applications. With
a wide capacity range and the patented Thermo-Flex™ coil design, these large unit coolers provide efficient, reliable operation. Features include a mill finish aluminum cabinet, 850 RPM motors for low noise and high reliability, liquid line solenoid wiring harness for faster installation, Schrader fitting for easier suction temperature measurement. Also, the large unit coolers have captive fasteners on access panels for easy servicing — no fumbling with loose bolts and nuts. The HHA Series also has a standardized terminal board for easier field wiring. Options include high CFM motor and fan combinations, totally enclosed motors, low temp motors for blast cooling, long air throw collars for large Warehouse/Industrial applications and insulated drain pans. PSC motors come standard to help you save energy.
HHA Model HHA520 HHA630 HHA750 HHA850 HHA930 HHA1100 HHA1170 HHA1400 HHA1610 HHA1900 HHA2200 HHA2440 HHA2160* HHA2500* HHA2780*
Capacity (BTUH)
Fan
10°F TD Qty. +25 SST 52,000 63,000 75,000 85,000 93,000 110,000 117,000 140,000 161,000 190,000 220,000 244,000 216,000 250,000 278,000
2 2 3 3 4 4 3 3 3 3 4 4 3 4 4
CFM 9,000 9,000 12,600 12,600 16,800 16,800 20,700 20,700 24,300 26,550 30,400 35,400 25,950 29,600 34,600
Motor (Total FLA) 208-230/1/60 460/1/60 Dia. 208(in.) Wired Wired 230/3/60 Wired Wired 1 ph. 3 ph. 1 ph. 3 ph. 24 6.4 5.2 3.4 24 6.4 5.2 3.4 24 9.6 5.5 7.8 3.0 24 9.6 5.5 7.8 3.0 24 12.8 8.7 10.4 4.7 24 12.8 8.7 10.4 4.7 30 13.8 30 13.8 30 19.8 30 21.0 30 26.4 30 28.0 30 21.0 30 26.4 30 28.0 -
Dimensions (in.)
Connections (in.)1
460/ 3/60
L
H
D
2.6 2.6 3.9 3.9 5.2 5.2 6.9 6.9 9.9 10.5 13.2 14.0 10.5 13.2 14.0
83-3/32 83-3/32 105-5/32 105-5/32 135-7/32 135-7/32 135-13/32 135-13/32 135-13/32 142-1/2 185-1/2 185-1/2 142-1/2 185-1/2 185-1/2
40-11/32 40-11/32 40-11/32 40-11/32 40-11/32 40-11/32 50-5/16 50-5/16 55-13/16 55-13/16 50-5/16 56-1/4 55-13/16 50-5/16 56-1/4
29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32
Approx. Coil Ext. Net Wt. Suction Inlet Equal. (lbs.) ODF ODF ODF 1-1/8 1-5/8 1/4 270 1-1/8 1-5/8 1/4 300 1-3/8 2-1/8 1/4 390 1-3/8 2-1/8 1/4 430 1-3/8 2-1/8 1/4 515 1-3/8 2-1/8 1/4 565 1-3/8 2-1/8 1/4 738 1-5/8 2-1/8 1/4 800 1-3/8† 2-1/8† 1/4† 850 1-3/8 2-5/8 1/4 1,160 1-3/8 2-5/8 1/4 1,500 1-5/8 2-5/8 1/4 1,600 1-3/8 2-5/8 1/4 1,160 1-3/8 2-5/8 1/4 1,500 1-3/8 2-5/8 1/4 1,600
Large Unit Coolers Electric Defrost Models HHE/HHL offer the same benefits as air defrost and are ideal for warehouse cooler/freezer applications. Capacity (BTUH)
Fan
HHE/HHL Model 10°F TD Qty. -20 SST
CFM
Motor (Total FLA) 208-230/60 460/1/60 Dia. 208(in.) Wired Wired 230/3/60 Wired Wired 1 ph. 3 ph. 1 ph. 3 ph.
HHE450 HHE550 HHE640 HHE740 HHE810 HHE950 HHE1020 HHE1200 HHE1390 HHE1650 HHE2120
45,000 55,000 64,000 74,000 81,000 95,000 102,000 120,000 139,000 165,000 212,000
2 2 3 3 4 4 3 3 3 3 4
9,000 9,000 12,600 12,600 16,800 16,800 20,700 20,700 24,300 26,550 35,400
24 24 24 24 24 24 30 30 30 30 30
6.4 6.4 -
5.5 5.5 8.7 8.7 -
5.2 5.2 7.8 7.8 10.4 10.4 13.8 13.8 19.8 21.0 28.0
HHL400 HHL480 HHL560 HHL650 HHL710 HHL840 HHL890 HHL1050 HHL1220 HHL1440 HHL1860
40,000 48,000 56,000 65,000 71,000 84,000 89,000 105,000 122,000 144,000 186,000
2 2 3 3 4 4 3 3 3 3 4
9,400 9,400 13,200 13,200 17,600 17,600 21,600 21,600 25,200 27,600 36,800
24 24 24 24 24 24 30 30 30 30 30
6.4 6.4 -
5.5 5.5 8.7 8.7 -
5.2 5.2 7.8 7.8 10.4 10.4 13.8 13.8 19.8 21.0 28.0
460/ 3/60
L
HHE Models 6 Fins Per Inch 3.4 2.6 83-3/32 3.4 2.6 83-3/32 3.0 3.9 105-5/32 3.0 3.9 105-5/32 4.7 5.2 135-7/32 4.7 5.2 135-7/32 6.9 135-13/32 6.9 135-13/32 9.9 135-13/32 10.5 142-1/2 14.0 185-1/2 HHL Models 4 Fins Per Inch 3.4 2.6 83-3/32 3.4 2.6 83-3/32 3.0 3.9 105-5/32 3.0 3.9 105-5/32 4.7 5.2 135-7/32 4.7 5.2 135-7/32 6.9 135-13/32 6.9 135-13/32 9.9 135-13/32 10.5 142-1/2 14.0 185-1/2
* These models are 8 fins per inch; all other air defrost models are 6 fins per inch. 1 Drain FPT is 1-1/4" for all models. † (2) connections required.
12
Dimensions (in.)
Connections (in.)1
Approx. Coil Ext. Net Wt. Suction Inlet Equal. (lbs.) ODF ODF ODF
H
D
40-11/32 40-11/32 40-11/32 40-11/32 40-11/32 40-11/32 50-5/16 50-5/16 55-13/16 55-13/16 56-1/4
29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32
1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-3/8† 1-3/8 1-5/8
1-5/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8† 2-5/8 2-5/8
1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4† 1/4 1/4
280 310 405 445 535 585 753 815 865 1,175 1,620
40-11/32 40-11/32 40-11/32 40-11/32 40-11/32 40-11/32 50-5/16 50-5/16 55-13/16 55-13/16 56-1/4
29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32
1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-3/8† 1-3/8 1-5/8
1-5/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8† 2-5/8 2-5/8
1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4† 1/4 1/4
277 306 400 440 528 578 744 805 854 1,160 1,600
Warehouse Unit Coolers Large Unit Coolers Hot Gas Defrost Models HHG/HHF offer the same benefits as air defrost and are ideal for warehouse cooler/freezer applications. Also, optional field or factory-installed hot gas kits are available. Capacity (BTUH) HHG/ HHF Model
1 †
Fan
Motor (Total FLA) 208230/1/60
10°F TD Qty. -20 SST
CFM
Dimensions (in.)
Connections (in.)1
460/1/60
Dia. 208460/ (in.) Wired Wired 230/3/60 Wired Wired 3/60 1 ph. 3 ph.
L
H
D
1 ph. 3 ph.
HHG450 HHG550 HHG640 HHG740 HHG810 HHG950 HHG1020 HHG1200 HHG1390 HHG1650 HHG2120
45,000 55,000 64,000 74,000 81,000 95,000 102,000 120,000 139,000 165,000 212,000
2 2 3 3 4 4 3 3 3 3 4
9,000 9,000 12,600 12,600 16,800 16,800 20,700 20,700 24,300 26,550 35,400
24 24 24 24 24 24 30 30 30 30 30
6.4 6.4 -
5.5 5.5 8.7 8.7 -
5.2 5.2 7.8 7.8 10.4 10.4 13.8 13.8 19.8 21.0 28.0
HHF400 HHF480 HHF560 HHF650 HHF710 HHF840 HHF890 HHF1050 HHF1220 HHF1440 HHF1860
40,000 48,000 56,000 65,000 71,000 84,000 89,000 105,000 122,000 144,000 186,000
2 2 3 3 4 4 3 3 3 3 4
9,400 9,400 13,200 13,200 17,600 17,600 21,600 21,600 25,200 27,600 36,800
24 24 24 24 24 24 30 30 30 30 30
6.4 6.4 -
5.5 5.5 8.7 8.7 -
5.2 5.2 7.8 7.8 10.4 10.4 13.8 13.8 19.8 21.0 28.0
HHG Models 6 Fins Per Inch 3.4 2.6 83-3/32 40-11/32 3.4 2.6 83-3/32 40-11/32 3.0 3.9 105-5/32 40-11/32 3.0 3.9 105-5/32 40-11/32 4.7 5.2 135-7/32 40-11/32 4.7 5.2 135-7/32 40-11/32 6.9 135-13/32 50-5/16 6.9 135-13/32 50-5/16 9.9 135-13/32 55-13/16 10.5 142-1/2 55-13/16 14.0 185-1/2 56-1/4 HHF Models 4 Fins Per Inch 3.4 2.6 83-3/32 40-11/32 3.4 2.6 83-3/32 40-11/32 3.0 3.9 105-5/32 40-11/32 3.0 3.9 105-5/32 40-11/32 4.7 5.2 135-7/32 40-11/32 4.7 5.2 135-7/32 40-11/32 6.9 135-13/32 50-5/16 6.9 135-13/32 50-5/16 9.9 135-13/32 55-13/16 10.5 142-1/2 55-13/16 14.0 185-1/2 56-1/4
Coil Inlet ODF
Hot Ext. Suct. Gas Equal. ODF ODF Side Port
Hot Gas Drain Pan Ref Conn
App. Net Wt. (lbs.)
29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32
1-1/8 1-5/8 1-1/8 1-5/8 1-3/8 2-1/8 1-3/8 2-1/8 1-3/8 2-1/8 1-3/8 2-1/8 1-3/8 2-1/8 1-5/8 2-1/8 1-3/8† 2-1/8† 1-3/8† 2-5/8† 1-3/8† 2-5/8†
1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4† 1/4† 1/4†
5/8 5/8 7/8 7/8 7/8 7/8 7/8 1-1/8 7/8† 7/8† 7/8†
1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8
280 310 405 445 535 585 753 815 865 1,175 1,620
29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 29-1/2 41-3/32 41-3/32 41-3/32 41-3/32 41-3/32
1-1/8 1-5/8 1-1/8 1-5/8 1-3/8 2-1/8 1-3/8 2-1/8 1-3/8 2-1/8 1-3/8 2-1/8 1-3/8 2-1/8 1-5/8 2-1/8 1-3/8† 2-1/8† 1-3/8† 2-5/8† 1-3/8† 2-5/8†
1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4† 1/4† 1/4†
5/8 5/8 7/8 7/8 7/8 7/8 7/8 1-1/8 7/8† 7/8† 7/8†
1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8
277 306 400 440 528 578 744 805 854 1,160 1,600
Drain FPT is 1-1/4" for all models. (2) connections required.
What is Thermo-Flex™ coil design? Chandler’s innovative coil design utilizes a new and unique approach to coil expansion that virtually eliminates the possibility of leaks at tube sheets and coil supports. Our engineers conceived the design after intense analysis of the cause of common coil failures. Through the use of accelerated test procedures and computer simulation, our engineers pinpointed the primary stress points of a coil during its operation. The Thermo-Flex™ coil design for the evaporator (U.S. Patent No. 5,584,340) allows the coil to ‘flex’ during periods of defrost which result in expansion of the coil surface. By eliminating the possibility of wear at critical stress areas, the integrity and longevity of the unit are dramatically increased. The result is a product which greatly enhances overall system reliability and reduces risk of costly refrigerant loss. To prove our claim, Chandler offers a five-year limited guarantee against leaks at tube sheets and center supports for all medium profile and large unit cooler models.
13
Packaged Refrigeration Systems PRO3 Top Mount Packaged Refrigeration Systems Models PTN/PTT are an evaporator and condensing unit all in one package. This unit is designed to maximize storage area inside a cooler or freezer and is ideal for small- to medium-sized restaurant and convenience store application where holding temperature is the primary goal. Shaded Pole motors standard for both condensing unit and evaporator section, PSC motors optional for for both condensing unit and evaporator section, EC motors available for evaporator section only.
EASE OF INSTALLATION AND SERVICE
ENERGY EFFICIENT | ENVIRONMENTALLY FRIENDLY
• Installation takes a fraction of the time required for a split system: no piping or loose components to install, refrigerant is pre-charged at factory and a field superheat adjustment is not required (see installation manual for more information)
• Energy Solutions® energy-efficient motors from InterLink™ Commercial Refrigeration Parts: – PSC motors standard in both condensing unit and evaporator section – EC motors optional, but may be required in certain installations (evaporator section only)
• No drain line required for indoor units. Indoor models come with a condensate evaporation pan • Flexible design allows for multiple installation methods: optimized for indoor use, but outdoor models available with weatherhood installed. Outdoor models also come with: crankcase heater, drain line heater and fan-cycling for head pressure control • Maximizes storage area in a cooler or freezer: evaporator grill mounts flush on a standard 4 or a recessed in a 5-1/2" ceiling panel
• Reduced refrigerant charge: system uses as little as 10 percent* of refrigerant required for a comparable split system
RELIABLE | DURABLE • System is fully-assembled and quality-tested at the factory • Electronic control provides accurate temperature control
EASE OF USE
• Liquid-line filter drier (medium and large cabinet only)
• System is factory-assembled, evacuated, charged, run-tested and wired; no additional components or refrigerant charging required; most models come with a 26 power cord ready to plug-in
• Two-year parts warranty * Results may vary. Estimate based on a typical 25-foot refrigerant line.
• Controls preset for typical applications: +35° F for coolers, -10° F, for freezers and are easy to adjust (019L6 set for 0° F)
Performance Data Coolers - Air Defrost System Model PTN024H2 PTN029H2 PTN040H2 PT*047H2 PT*063H2 PT*072H2 PT*099H2 PT*128H2
Freezers - Electric Defrost Systems
90° F Ambient 35° F 38° F 2,630 2,740 3,170 3,290 4,380 4,500 5,150 5,480 6,910 7,340 7,890 8,330 10,850 11,730 14,030 15,010
Model PTN019L6 PT*021L6 PT*031L6 PT*044L6 PT*052L6 PT*069L6
0° F 2,640 2,860 4,500 6,260 7,470 9,670
90° F Ambient -10° F – 2,300 3,400 4,830 5,720 7,850
-20° F – 1,430 2,200 3,630 4,170 5,600 MEA Accepted
Electrical Data Model
Voltage
MCA
MOPD
PTN024H2A^ PTN029H2A^ PTN040H2A^ PT*047H2A^ PT*047H2B^ PT*063H2B^ PT*072H2B^ PT*099H2B^ PT*099H2C^ PT*128H2B^ PT*128H2C^ PTN019L6A^ PT*021L6A^ PT*021L6B^ PT*031L6B^ PT*044L6B^ PT*052L6B^ PT*052L6C^ PT*069L6B^ PT*069L6C^
115/1/60 115/1/60 115/1/60 115/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/3/60 208-230/1/60 208-230/3/60 115/1/60 115/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/3/60 208-230/1/60 208-230/3/60
10.2 10.6 11.7 16.9 8.6 11.6 10.9 17.1 15.4 20.3 14.8 13.0 14.5 7.6 13.8 15.9 18.1 12.2 23.8 15.9
15 15 15 20 15 15 15 20 20 30 20 20 20 15 15 20 20 15 30 20
*T For Outdoor, N for Indoor. ^ H for PSC, E for EC motor on evaporator section only.
14
Unit Amps 10.2 10.6 11.7 14.2 7.3 9.9 9.3 14.7 13.3 17.2 12.8 13.0 12.3 6.5 11.6 13.3 15.3 13.0 20.0 14.2
Evaporator CFM 340 340 340 350 350 550 500 875 875 825 825 340 350 350 550 520 900 900 875 875
Plug Supplied Yes Yes Yes Yes Yes 1 Yes 1 Yes 1 Yes 1 No No No Yes Yes Yes 1 Yes 1 Yes 1 Yes 1 No No No
Matching NEMA Receptacle 5-20R 5-20R 5-20R 5-20R 6-15R 6-15R 6-15R 6-20R – – – 5-20R 5-20R 6-15R 6-15R 6-20R 6-20R – – –
1 Plug Supplied on Indoor models only. 2 See technical bulletin for dimensions.
Cabinet Size2 Small Small Small Medium Medium Medium Medium Large Large Large Large Small Medium Medium Medium Medium Large Large Large Large
Approx. Net Weight (lbs.) 88 90 92 192 192 207 211 270 265 290 285 101 213 213 221 225 275 270 280 275
Packaged Refrigeration Systems PRO3 Side Mount Packaged Refrigeration Systems Model PST is an evaporator and condensing unit all in one package. This unit is optimized for
outdoor applications and is ideal for small- to medium-sized restaurant and convenience store applications where maximum airflow is essential for pulling down the temperature of foods or beverages. The Side Mount PRO3 is also available with electric defrost medium temperature models, ensuring maximum performance in storage applications slightly above freezing. PSC motors standard for both condensing unit and evaporator section, EC motors available for evaporator section only. EASE OF INSTALLATION AND SERVICE • Installation takes a fraction of the time required for a split system: refrigerant is pre-charged at factory, superheat adjustment is not required and unit slides into slots in standard walk-in panel (see installation manual for more information) • Designed for simple serviceability: the condensing unit section’s cabinet door can be quickly removed; in addition, the electrical box is located outside the cabinet for easy access
• Electric defrost standard for medium temperature models, allowing for maximum performance in storage applications just above 32°F • Fan-cycling for head pressure control • Crankcase heater • Drain line heater
RELIABLE | DURABLE
• Flexible design allows for multiple installation methods: Optimized for outdoor use, but can be used indoors as well (with drain connection)
• System is fully-assembled and quality-tested at the factory
• Lifting lugs and hanging brackets in evaporating section allow for easy installation
• Liquid-line filter drier
EASE OF USE
• Electronic microprocessor control provides accurate temperature control • Two-year parts warranty
ENVIRONMENTALLY FRIENDLY
• System is factory-assembled, evacuated, charged, run-tested and wired; no additional components required • Controls preset for typical applications: +38° F for high temp. coolers, +35° F for medium temp. coolers, -10° F for freezers and are easy to adjust
PERFORMANCE • Maximized airflow: evaporator placement in walk-in box with pullthrough fans – Suitable for temperature pull-down and holding temperature • Increased condenser capacity, by avoiding compressor heat across the coil – Improved tolerance in high-ambient conditions
• Energy Solutions® energy-efficient motors from InterLink™ Commercial Refrigeration Parts: – PSC motors standard in both condensing unit and evaporator section – EC motors optional, but may be required in certain installations (evaporator section only) • Reduced refrigerant charge: the PRO3 Side Mount packaged refrigeration system can use as little as 10-15 percent* of refrigerant required for a comparable split system *Results may vary. Estimate based on a typical a typical 100-foot refrigerant line length.
Performance Data Coolers - Air Defrost System Model PST070H6B^ PST090H6B^ PST131H6B^ PST147H6B^
MEA Accepted
Coolers - Electric Defrost System
90° F Ambient 35° F 38° F 6,860 7,198 8,928 9,363 12,859 13,540 14,545 15,245
Model PST066M6B^ PST086M6B^ PST124M6B^ PST141M6B^
90° F Ambient 35° F 6,860 8,928 12,859 14,545
Freezers - Electric Defrost System Model PST034L6B^ PST051L6B^ PST057L6B^ PST077L6B^
90° F Ambient 0° F -10° F -20° F 5,031 3,651 2,395 6,922 5,428 3,943 7,994 6,079 4,153 10,602 8,179 6,030
Electrical Data Model PST070H6B^ PST090H6B^ PST131H6B^ PST147H6B^ PST066M6B^ PST086M6B^ PST124M6B^ PST141M6B^ PST034L6B^ PST051L6B^ PST057L6B^ PST077L6B^
Voltage 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60 208-230/1/60
MCA 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.7
MOPD 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 35.0
Evaporator CFM 625 625 1,350 1,350 625 625 1,350 1,350 625 625 1,350 1,350
Cabinet Size¹ Small Small Large Large Small Small Large Large Small Small Large Large
Approx. Net Weight (lbs.) 260 265 320 325 260 265 320 325 260 265 320 325
^ H for PSC, E for EC motor on evaporator section only. 1 See technical bulletin for dimensions.
15
Condensing Units 1/2 - 5 HP Indoor/Outdoor Condensing Units with Hermetic Compressors Model CH
condensing units are ideal for convenience store, restaurant and other commercial applications. The CH model condensing units feature a hermetic refrigeration compressor with oversized HyperCore™ microchannel condenser. Also, the CH Series condensing units have a shut off valve in the discharge line of the hermetic compressor. PSC motors come standard to help you save energy. UL listed for US and Canada. Available with factory installed Smart Defrost Kit™ (SDK) system and Variable Speed EC (VSEC) motor with Orbus™ Controller.
HyperCore
TM
microchannel coil technology
Variable Speed EC (VSEC) motors with Orbus™ Controller by InterLink™ VSEC motors by InterLink™ with the proprietary Orbus™ Controller are available as an option on 1/2-6 HP air-cooled condensing units from Chandler. Choosing this option saves energy and reduces costs for the end user by controlling the speed of motors in response to loads. To achieve an optimal system that is both energy efficient and environmentally friendly, choose the following options for your unit: VSEC motors with Orbus™ Controller, factory-installed Smart Defrost Kit™ and a variety of compressor options, including efficient scroll, hermetic and semi-hermetic compressor. These options provide unmatched energy efficiency — the perfect solution for applications where energy savings is essential for success.
CH Series Indoor or Outdoor Installation, Hermetic Compressors (1/2 - 5 HP) CH Model CH*005H6 CH*009H6 CH*010H6† CH*015H6 CH*025H6 CH*032H6 CH*040H6 CH*050H6 CH*005X6 CH*008X6 CH*009X6 CH*010X6† CH*015X6 CH*020X6 CH*025X6 CH*030X6 CH*032X6 CH*040X6 CH*050X6 CH*011L6 CH*014L6 CH*019L6 CH*025L6 CH*031L6 CH*005H2 CH*008H2 CH*010H2 CH*015H2 CH*020H2 CH*029M2 CH*030H2 CH*040H2 CH*050H2
Compressor Refrigerant RST45C1E RST64C1E RS70C1E CS10K6E CS14K6E CS20K6E CS27K6E2 CS33K6E2 RST45C1E RST55C1E RST64C1E RS70C1E CS10K6E CS12K6E CS14K6E CS18K6E CS20K6E CS27K6E CS33K6E CF04K6E CF06K6E CF06K6E CF09K6E CF12K6E ART82C1 RS64C2 RS70C1 CR18KQ CR24KQ CR37KQ CR37KQ CR53KQ CRN-0500
Suction Temp.
High Temp R-404A/507
35°F
Extended Temp R-404A/507
25°F
Low Temp R-404A/507
-10°F
Medium & High Temp R-22
25°F
* = T for Outdoor, N for Indoor, S for Beacon II™ † = RS compressor not suitable for R-507 1 Minimum Circuit Amps - Air Defrost Type Unit 2 230 Volt only
16
Capacity (BTUH) Connections (ID) 95° F Ambient 7,790 11,080 11,960 18,400 23,030 37,110 45,670 50,060 5,970 7,070 8,420 8,850 13,960 16,000 17,490 25,490 27,890 37,270 41,000 4,920 7,750 8,750 12,000 14,360 4,870 7,740 8,150 12,210 16,910 22,780 28,090 38,840 44,050
Liquid Suction 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 3/8 3/8 3/8 3/8 1/2 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2
1/2 5/8 5/8 5/8 7/8 7/8 1-1/8 1-1/8 1/2 1/2 5/8 5/8 5/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 5/8 5/8 5/8 7/8 7/8 1/2 1/2 5/8 5/8 7/8 7/8 7/8 1-1/8 1-1/8
Unit MCA1
Dimensions (in.)
208-230/1 208-230/3 460/3 15.0 15.0 15.0 15.0 20.0 25.9 33.1 41.2 15.0 15.0 15.0 15.0 15.0 15.0 15.0 21.0 24.0 30.3 38.0 15.0 15.0 15.0 20.0 22.3 15.0 15.0 15.0 15.0 20.0 21.8 24.3 36.0 42.0
– – 15.0 15.0 15.0 20.2 21.1 24.2 – – – 15.0 15.0 15.0 15.0 15.0 20.0 20.7 24.5 15.0 15.0 15.0 15.0 15.0 – – 15.0 15.0 15.0 15.0 30.0 23.9 28.0
– – – – – – – – – – – – – – 15.0 15.0 15.0 15.0 15.0 – – – – 15.0 – – – 15.0 15.0 15.0 15.0 15.0 15.0
L
H
D
23-3/4 23-3/4 23-3/4 37-3/4 37-3/4 42-1/2 42-1/2 42-1/2 23-3/4 23-3/4 23-3/4 23-3/4 37-3/4 37-3/4 37-3/4 42-1/2 42-1/2 42-1/2 42-1/2 23-3/4 23-3/4 37-3/4 37-3/4 37-3/4 23-3/4 23-3/4 23-3/4 37-3/4 37-3/4 37-3/4 42-1/2 42-1/2 42-1/2
17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 29-3/4 29-3/4 29-3/4 17-1/2 17-1/2 17-1/2 17-1/4 17-1/4 17-1/4 17-1/4 29-3/4 29-3/4 29-3/4 29-3/4 17-1/4 17-1/4 17-1/4 17-1/4 19-3/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 19-1/4 29-3/4 29-3/4 29-3/4
28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 30-1/4 30-1/4 30-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 30-1/4 30-1/4 30-1/4 30-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 30-1/4 30-1/4 30-1/4
Approx. Net Wt. (lbs.) 135 144 138 193 208 275 281 313 135 135 144 138 193 203 208 290 275 281 313 139 170 200 222 223 135 141 136 189 193 214 281 299 310
Condensing Units 2 - 6 HP Indoor/Outdoor Condensing Units with Scroll® Compressors Model CZ features a complete line of Copeland’s Scroll® compressors. These condensing units have an oversized HyperCore™ microchannel condenser which allows units to operate in high ambient for 40° F suction temperature and below. PSC motors come standard to help you save energy. UL listed for US and Canada. Available with factory installed Smart Defrost Kit™(SDK) system and Variable Speed EC (VSEC) motor with Orbus™ Controller.
CZ Series Indoor or Outdoor Installation, Scroll® Compressors (2-6 HP) CZ Model CZ*020M6 CZ*025M6 CZ*030M6 CZ*035M6 CZ*045M6 CZ*055M6 CZ*060M6 CZ*020L6 CZ*025L6 CZ*030L6 CZ*035L6 CZ*045L6 CZ*055L6 CZ*060L6
Compressor Refrigerant ZS15K4E ZS19K4E ZS21K4E ZS26K4E ZS30K4E ZS38K4E ZS45K4E ZF06K4E ZF08K4E ZF09K4E ZF11K4E ZF13K4E ZF15K4E ZF18K4E
Suction Temp.
Medium Temp. R-404A/ 507
25°F
Low Temp. R-404A/ 507
-10°F
Capacity (BTUH) 95°F Ambient 18,930 22,490 27,270 32,820 38,230 45,160 52,340 9,540 11,850 13,200 15,860 19,490 23,820 28,970
Connections (in.) Liquid Suction IDS IDS 1/2 7/8 1/2 7/8 1/2 7/8 1/2 7/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 1/2 7/8 1/2 7/8 1/2 7/8 1/2 7/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8
208230/1 20 20 22 27 34 40 – 20 20 20 24 34 40 –
Unit MCA1 208230/3 15 15 20 20 20 28 30 15 15 15 20 20 28 30
Dimensions (in.) 460/3
L
H
D
15 15 15 15 15 15 15 15 15 15 15 15 15 15
37-3/4 37-3/4 42-1/2 42-1/2 42-1/2 42-1/2 42-1/2 37-3/4 37-3/4 37-3/4 37-3/4 42-1/2 42-1/2 42-1/2
19-3/4 19-3/4 29-3/4 29-3/4 29-3/4 29-3/4 29-3/4 19-3/4 19-3/4 19-3/4 19-3/4 29-3/4 29-3/4 29-3/4
28-1/4 28-1/4 30-1/4 30-1/4 30-1/4 30-1/4 30-1/4 28-1/4 28-1/4 28-1/4 28-1/4 30-1/4 30-1/4 30-1/4
Approx. Net Wt. (lbs.) 209 218 287 290 317 317 317 209 218 218 217 307 313 317
NOTE: The ZF compressor comes with liquid injection. For R-22 model capacity information, see product bulletin.
1/2 - 5 HP Indoor/Outdoor Condensing Units with Semi-Hermetic Compressors Model CS
condensing units are ideal for convenience store, restaurant and other commercial applications. The units feature a semi-hermetic refrigeration compressor, which is spring-mounted with vibration eliminators on all 1-1/2 to 6 HP (1/2 to 1 HP compressors are rigid mounted and have a discharge loop). Also, these condensing units come standard with an oversized HyperCore™ microchannel coil technology condenser that works in high ambients, encapsulated auto-reset high pressure controls to eliminate leaks, pre-painted steel cabinet for superior strength and corrosion protection, and suction and discharge service valves. PSC motors come standard to help you save energy. UL listed for US and Canada. Available with factory installed Smart Defrost Kit™(SDK) system and Variable Speed EC (VSEC) motor with Orbus™ Controller.
CS Series Indoor or Outdoor Installation, Semi-Hermetic Compressors (1/2-5 HP) CS Model CS*005H2 CS*008H2 CS*008M2 CS*010H2 CS*010M2 CS*015H2 CS*020H2 CS*020M2 CS*021M2 CS*029M2 CS*030H2 CS*040H2 CS*050H2 CS*050M2 CS*005M6 CS*010M6 CS*020M6 CS*021M6 CS*030M6 CS*040M6 CS*005L6 CS*008L6 CS*010L6 CS*015L6 CS*020L6 CS*021L6 CS*030L6 CS*030E6 CS*040L6
Compressor HAG-0050 KAN-0075 KAE-0075 KAR-0100 KAM-0100 KAG-0150 ERA-0200 KAK-0200 ERC-0200 ERF-0310 ERF-0310 NRB-0400 NRA-0500 NRM-0500 HAJ-005E KAR-010E KAK-020E ERC-021E ERF-031E NRB-040E KAN-005E KAM-007E KAJ-010E KAL-015E EAD-020E EAV-021E LAH-032E LAC-032E NRD-040E^ NRD-032E^^
Refrigerant
Suction Temp.
Medium & High Temp R-22
25°F
Medium Temp R-404A/507
25°F
Low Temp R-404A/507
-10°F
Capacity (BTUH) 95° F Ambient
* = T for Outdoor, N for Indoor, S for Beacon II™ ^ NRD1-040E Compressor is Single Phase & uses R-404A only. ^^ Uses R-404A & 507 in 3 phase model.
4,280 6,630 7,510 9,260 9,580 12,230 13,700 16,530 17,640 24,720 26,800 37,830 43,310 51,590 5,210 9,140 16,240 18,850 29,690 39,240 2,580 4,320 5,790 8,920 9,870 11,280 16,930 15,700†† 22,530
Connections (in.) Liquid Suction (IDS) (IDS) 3/8 1/2 3/8 5/8 3/8 5/8 3/8 5/8 3/8 5/8 3/8 7/8 3/8 7/8 3/8 7/8 3/8 7/8 1/2 7/8 1/2 7/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 3/8 1/2 3/8 5/8 3/8 7/8 3/8 7/8 1/2 7/8 1/2 1-1/8 3/8 1/2 3/8 5/8 3/8 5/8 3/8 7/8 3/8 7/8 3/8 7/8 1/2 7/8 1/2 7/8 1/2
1-1/8
208230/1 15 15 15 15 15 15 15† 15 15† 21† 23† – – – 15 15 15 – 23† – 15 15 15 15 15† 20 20† 20† 35†
Unit MCA1 208230/3 15 15 15 15 15 15 15 15 15 15 20 28 25 31 – 15 15 15 20 28 15 15 15 15 15 15 20 15 22
Minimum Circuit Amps - Air Defrost Type Unit † Units are 230 volt † † Rated at -20˚ F
Dimensions (in.) 460/3
L
H
D
– – – – – 15 15 – 15 15 15 15 15 15 – – – 15 15 15 – – – – – 15 15 15
23-3/4 23-3/4 23-3/4 23-3/4 23-3/4 37-3/4 37-3/4 37-3/4 37-3/4 37-3/4 42-1/2 42-1/2 42-1/2 42-1/2 23-3/4 23-3/4 37-3/4 37-3/4 42-1/2 42-1/2 23-3/4 23-3/4 23-3/4 37-3/4 37-3/4 37-3/4 37-3/4 37-3/4
17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 19-3/4 29-3/4 29-3/4 29-3/4 29-3/4 17-1/4 17-1/4 17-1/4 17-1/4 29-3/4 29-3/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 17-1/4 19-3/4 19-3/4
28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 30-1/4 30-1/4 30-1/4 30-1/4 28-1/4 28-1/4 28-1/4 28-1/4 30-1/4 30-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4 28-1/4
Approx. Net Wt. (lbs.) 161 180 180 175 178 221 293 189 301 391 385 460 462 462 161 178 189 301 397 460 172 172 178 225 291 301 357 391
15
42-1/2
29-3/4
30-1/4
457
1
17
Condensing Units 3-22 HP Indoor or Outdoor Condensing Units with Discus® or Scroll® Compressors Models HD/HZ 3-22 HP condensing unit’s enhanced grill design gives up to 40% more free-air area than before and
its vertical receiver needs less refrigerant to ensure a solid column of liquid reaches the expansion valve. Fan motors and serviceable components are accessible through the front grill for quick service and the sight glass is conveniently placed so that charging is quick, easy and accurate. Thorough cleaning of the coil is easier because the unit’s top is one piece and lighter for easy removal. A liquid base valve and suction service tap is placed on the outside of the cabinet for easy pump-downs and quick diagnosis. The footprint is smaller for easy jobsite placement. These condensing units utilize the Floating Tube™ coil design, which eliminates tube-sheet leaks, allowing Chandler to offer you a 5-year warranty (including labor and refrigerant) against tube-sheet leaks. PSC motors come standard to help you save energy.
HD Discus® Models Unit Model
Compressor Model
HD*0500H2 HD*0501H2 HD*0750H2 HD*0751H2 HD*0800H2 HD*1000H2 HD*1200H2 HD*1500H2 HD*0500M6 HD*0501M6 HD*0750M6 HD*0751M6 HD*0800M6 HD*1000M6 HD*1200M6 HD*1500M6 HD*0300L6 HD*0400L6 HD*0600L6 HD*0601L6 HD*0750L6 HD*0900L6 HD*1000L6 HD*1200L6 HD*1500L6 HD*2200L6 HD*0300L2 HD*0400L2 HD*0600L2 HD*0601L2 HD*0750L2 HD*0900L2 HD*1000L2 HD*1200L2 HD*1500L2 HD*2200L2
2DC3R53KE 2DD3R63KE 2DL3R78KE 2DA3R89KE 3DA3R10ME 3DB3R12ME 3DF3R15ME 3DS3R17ME 2DC3R53KE 2DD3R63KE 2DL3R78KE 2DA3R89KE 3DA3R10ME 3DB3R12ME 3DF3R15ME 3DS3R17ME 2DF3F16KE 2DL3F20KE 2DB3F25KE 3DA3F28KE 3DB3F33KE 3DF3F40KE 3DS3F46KE 4DA3F47KE 4DL3F63KE 4DT3F76KE 2DF3F16KE 2DL3F20KE 2DB3F25KE 3DA3F28KE 3DB3F33KE 3DF3F40KE 3DS3F46KE 4DA3F47KE 4DL3F63KE 4DT3F76KE
Refrigerant
Suction BTUH Temp. 95°F Amb.
High Temp. R-22
25°F
Medium Temp. R-404A/R507
20°F
Low Temp. R-404A/R507
-10°F
Low Temp. R-22
-10°F
43,380 49,380 61,860 71,930 88,450 103,250 115,210 134,780 39,280 45,530 56,000 68,060 80,170 93,930 111,940 128,610 25,320 29,620 35,160 38,920 45,630 59,280 64,870 70,880 89,380 103,010 22,160 25,870 31,180 34,760 42,060 53,290 57,230 63,600 79,760 92,430
HZ Scroll® Models Unit Model
Compressor Model
HZ*0650M6 HZ*0700M6 HZ*0750M6 HZ*0860M6 HZ*1000M6 HZ*1401M6 HZ*0750L6 HZ*1000L6 HZ*1300L6 HZ*1500L6 HZ*0750L2 HZ*1000L2 HZ*1300L2 HZ*1500L2
ZB50KCE ZB58KCE ZB66KCE ZB76KCE ZS92K4E ZS11M4E ZF24K4E ZF33K4E ZF40K4E ZF48K4E ZF24K4E ZF33K4E ZF40K4E ZF48K4E
Refrigerant
Medium Temp. R404A/R-507
25°F
Low Temp. R-404A/R507
-10°F
Low Temp. R-22
-10°F
*= T for Outdoors, N for Indoors, S for Beacon II™
18
Suction BTUH Temp. 95°F Amb. 58,130 69,460 80,250 90,090 108,200 128,920 32,650 45,630 57,900 65,370 30,610 42,940 53,530 60,860
Air Defrost Min. Circuit Amp 208460/3/60 230/3/60 27.7 15.0 27.7 15.0 38.1 20.0 41.3 20.0 51.4 26.2 54.3 26.2 59.4 30.2 75.7 36.9 27.7 15.0 27.7 15.0 38.1 20.0 41.3 20.0 51.4 26.2 54.3 26.2 59.4 30.2 75.7 36.9 20.6 10.8 32.2 13.4 34.4 16.8 32.7 15.4 37.2 19.5 46.9 22.6 51.9 24.6 59.9 30.0 67.8 33.9 80.9 40.5 20.6 15.0 32.2 15.0 34.4 20.0 32.7 20.0 37.2 20.0 46.9 22.6 51.9 24.6 59.9 30.0 67.8 33.9 80.9 40.5
Air Defrost Min. Circuit Amp 208460/3/60 230/3/60 34.8 18.7 39.9 22.2 39.1 23.4 51.9 23.4 64.7 31.8 76.1 36.0 36.4 19.5 51.6 25.5 64.7 33.4 67.1 31.0 36.4 19.5 51.6 25.5 64.7 33.4 67.1 31.0
Connections (in.)
Dimensions (inches)
Liquid
Suction
Length
Width
Height
Net Wt. (lbs.)
1/2 1/2 1/2 5/8 5/8 5/8 5/8 7/8 1/2 1/2 1/2 5/8 5/8 5/8 5/8 7/8 1/2 1/2 1/2 1/2 1/2 5/8 5/8 7/8 7/8 7/8 1/2 1/2 1/2 1/2 1/2 5/8 5/8 7/8 7/8 7/8
1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8
36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 41-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 41-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 41-3/4 41-3/4 41-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 41-3/4 41-3/4 41-3/4
51-3/4 51-3/4 51-3/4 63-3/4 63-3/4 63-3/4 63-3/4 75-1/8 51-3/4 51-3/4 51-3/4 63-3/4 63-3/4 63-3/4 63-3/4 75-1/8 51-3/4 51-3/4 51-3/4 51-3/4 51-3/4 63-3/4 63-3/4 75-1/8 75-1/8 75-1/8 51-3/4 51-3/4 51-3/4 51-3/4 51-3/4 63-3/4 63-3/4 75-1/8 75-1/8 75-1/8
39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 48-3/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 48-3/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 48-3/4 48-3/4 48-3/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 48-3/4 48-3/4 48-3/4
751 751 761 985 1,020 1,045 1,065 1,182 751 751 761 985 1,020 1,045 1,065 1,182 737 741 751 781 805 1,030 1,035 1,199 1,234 1,224 737 741 751 781 805 1,030 1,035 1,199 1,234 1,224
Refrigerant Line Connections (OD)
Dimensions (in.)
Liquid
Suction
Length
Width
Height
Net Wt. (lbs.)
1/2 5/8 5/8 5/8 5/8 7/8 1/2 1/2 5/8 5/8 1/2 1/2 5/8 5/8
1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-1/8 1-1/8 1-3/8 1-3/8 1-1/8 1-1/8 1-3/8 1-3/8
36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 41-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4 36-3/4
51-3/4 63-3/4 63-3/4 63-3/4 63-3/4 75-1/8 51-3/4 51-3/4 63-3/4 63-3/4 51-3/4 51-3/4 63-3/4 63-3/4
39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 48-3/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4
574 800 813 818 908 1,235 671 671 910 891 671 671 910 891
Condensing Units 20 - 40 HP Outdoor Condensing Units with Discus® Compressors Model HDH outdoor Discus® condensing unit features a leak resistant design which includes
the Floating Tube™ coil design. The HDH features a high efficiency Copeland Discus® compressor. The electrical controls including compressor contactor and optional defrost control are located in an easily accessible control box with a hinged cover. UL listed for US and Canada.
HDH Discus® Compressor Model HDH Model HDH2000D6 HDH2500D6 HDH2600D6 HDH3000D6 HDH3500D6 HDH4000D6 HDH*2000D6 HDH*2500D6 HDH*2600D6 HDH*3000D6 HDH*3500D6 HDH*4000D6 HDH2700L6† HDH3000L6† HDH3100L6† ^ 230/3 * S for Beacon II™ †
Compressor 4DA3R18ME 4DH3R22ME 4DH3R22ME 4DJ3R28M3 6DH3R35ME 6DJ3R40ME 4DA3R18ME 4DH3R22ME 4DH3R22ME 4DJ3R28M3 6DH3R35ME 6DJ3R40ME 6DL3F93KE 6DT3F11ME 6DT3F11M3
Refrigerant
Suction Temp.
Medium Temp. R-22
25ºF
Medium Temp. R-404A/ R-507
25ºF
Low Temp. R-404A/ R-507
-10ºF
BTUH 95˚F Amb. 143,470 190,910 197,260 225,520 280,600 322,590 148,750 191,910 200,370 231,280 281,570 325,470 134,870 146,440 153,480
Min. Circuit Amp 208-230/ 3/60 87.9 105.3 109.7 123.0 137.8 176.3^ 87.9 105.3 109.7 123.0 137.8 176.3 103.7 120.4 124.8
460/ 3/60 43.9 52.7 54.9 61.5 68.9 88.1 43.9 52.7 54.9 61.5 68.9 88.1 51.9 60.2 62.4
Connections (in.)
Dimensions (in.)
Liquid
Suction
L
H
D
Approx. Net Wt. (lbs.)
7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8
1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8
102-1/2 102-1/2 132-1/2 132-1/2 132-1/2 132-1/2 102-1/2 102-1/2 132-1/2 132-1/2 132-1/2 132-1/2 102-1/2 102-1/2 132-1/2
48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4 48-3/4
42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4 42-1/4
1,131 1,206 1,362 1,372 1,492 1,542 1,131 1,206 1,362 1,372 1,492 1,542 1,206 1,406 1,452
Demand Cooling needs to be specified for use with R-22
19
Condensing Units 24 - 80 HP Dual Compressor Outdoor Condensing Units Model HDD condensing unit is a dual compressor vertical discharge outdoor condensing unit that utilizes Copeland Discus® compressors. A wide range of options are available that are ideal for large cold storage or warehouse applications. PSC motors come standard to help you save energy.
HDD Discus® Compressor Model HDD Model
Compressor
HDD3000H2 HDD4000H2 HDD5000H2 HDD5200H2 HDD6000H2 HDD7000H2 HDD7010H2 HDD8000H2 HDD3000M6 HDD4000M6 HDD5000M6 HDD5200M6 HDD6000M6 HDD7000M6 HDD8000M6 HDD3000C6 HDD4000C6 HDD5000C6 HDD6000C6 HDD7000C6 HDD8000C6 HDD2400L6 HDD3000L6 HDD4400L6 HDD5400L6 HDD6000L6 HDD2400L61 HDD3000L61 HDD4400L61 HDD5400L61 HDD6000L61
3DS3R17ME 4DA3R18ME 4DH3R22ME 4DH3R22ME 4DJ3R28ME 6DH3R35ME 6DG3R37ME 6DJ3R40ME 3DS3R17ME 4DA3R18ME 4DH3R22ME 4DH3R22ME 4DJ3R28ME 6DH3R35ME 6DJ3R40ME 3DS3R17ME 4DA3R18ME 4DH3R22ME 4DJ3R28ME 6DH3R35ME 6DJ3R40ME 4DA3F47KE 4DL3F63KE 4DT3F76KE 6DL3F93KE 6DT3F11ME 4DA3F47KE 4DL3F63KE 4DT3F76KE 6DL3F93KE 6DT3F11ME
Refrig.
High Temp. R-22
25°F
Medium Temp. R404A/ R-507
25°F
Comm. Temp. R404A/ R-507
10°F
Low Temp. R404A/ R-507
-10°F
Low Temp. R-22
-10°F
* MCA based on remote loads and one contactor 1 Must be ordered with demand cooling
20
Suction Temp.
BTUH 95°F Amb. 267,000 279,800 365,800 373,600 439,800 563,200 590,800 652,600 282,800 295,600 370,800 381,600 459,800 585,200 677,200 218,400 223,400 282,000 351,000 447,800 522,200 139,000 176,200 208,600 261,800 294,400 125,000 158,400 187,800 232,200 277,000
Air Defrost Min. Circuit Amp* 230/3/60 460/3/60 66.6 136.4 150.4 75.2 181.9 90.9 96.9 193.9 108.9 217.8 129.2 258.3 294.4 147.2 163.8 327.6 136.4 66.6 150.4 75.2 181.9 90.9 193.9 96.9 217.8 108.9 258.3 129.2 327.6 163.8 136.4 66.6 150.4 75.2 181.9 90.9 217.8 108.9 258.3 129.2 327.6 163.8 108.0 54.0 122.2 61.1 145.8 72.9 179.0 89.5 221.0 110.5 108.0 54.0 122.2 61.1 145.8 72.9 179.0 89.5 221.0 110.5
Connections (in.) Liquid 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 7/8 7/8 1-1/8 1-1/8 1-1/8 1-1/8 7/8 7/8 7/8 1-1/8 1-1/8 7/8 7/8 7/8 1-1/8 1-1/8
Suction 1-5/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 1-5/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 1-5/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 1-5/8 1-5/8 2-1/8 2-1/8 2-1/8 1-5/8 1-5/8 2-1/8 2-1/8 2-1/8
Dimensions (in.) L 151 151 151 179 179 233 233 233 151 151 151 179 179 233 233 151 151 151 179 233 233 151 151 151 151 179 151 151 151 151 179
H 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61 61
D 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88
Approx. Net Wt. (lbs.) 3,160 3,160 3,230 3,520 3,720 4,320 4,320 4,760 3,160 3,160 3,230 3,520 3,720 4,320 4,760 3,160 3,160 3,230 3,720 4,320 4,760 3,000 3,000 3,000 3,340 3,770 3,000 3,000 3,000 3,340 3,770
Condensing Units 1/2 - 6 HP Remote Water-Cooled Condensing Units with Hermetic or Scroll® Compressors Models HWN/ZWN series are water-cooled hermetic and Scroll® condensing units from 1/2 - 6 HP.
Condensing units’ component selection, location, base and unit dimensions are all optimized for easy field replacements or in new installations where space is limited. Extra space is provided inside the electrical box for easy servicing. The area is large enough to accommodate circuit breakers, compressor contactors, time clocks and all start components in one enclosure. Standard features include compressor isolations valves that enable services technicians to isolate the compressor for service. Also standard is the extra capacity receiver which provides total refrigerant pump down. Ideal for units requiring long line runs. These units are available with Copeland hermetic, Scroll® low and medium temperature compressors as well as hermetic low temperature compressors for R-22 and R-404A. These units are UL listed for US and Canada.
HWN Hermetic Compressor Model HWN Model
Compressor
HWN005H2 HWN008H2 HWN010H2 HWN015H2 HWN020H2 HWN030H2 HWN040H2 HWN050H2 HWN005X6 HWN008X6 HWN009X6 HWN010X6 HWN015X6 HWN020X6 HWN025X6 HWN030X6 HWN032X6 HWN040X6 HWN050X6 HWN011L6 HWN014L6 HWN025L6 HWN031L6
ART82C1 RS64C2 RS70C1 CR18KQ CR24KQ CR37KQ CR53KQ CRN50500 RS43C2E† RS55C2E† RS64C2E† RS70C2E† CS10K6E CS12K6E CS14K6E CS18K6E CS20K6E CS27K6E CS33K3E CF04K6E CF06K6E CF09K6E CF12K6E
Refrigerant
Suction Temp
Medium & High Temp R-22
20° F
Extended Temp R-404A/ R-507
10° F
Low Temp R-404A/ R-507
-10° F
Capacity* BTUH 5,390 7,500 8,810 11,240 14,330 23,660 33,740 40,460 4,060 5,280 6,395 6,800 9,710 11,490 13,630 17,400 19,220 23,901 28,838 5,310 8,700 12,590 16,060
Air Defrost Total MCA
Connections (in.) ODS
Dimensions (in.)
208-230/ 1/60
208-230/ 3/60
460/ 3/60
Liquid
Suction
L
H
D
Approx. Net Wt. (lbs.)
15 15 15 15 20 21 33 39 15 15 15 15 15 15 15 18 21 27 35 15 15 20 21
15 15 15 15 20 24 15 15 15 15 15 15 20 21 15 15 15 15
15 15 15 15 15 15 15 15 15 15 15
3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 3/8 3/8 3/8 1/2
1/2 1/2 5/8 5/8 5/8 7/8 7/8 7/8 1/2 1/2 5/8 5/8 5/8 7/8 7/8 7/8 7/8 7/8 7/8 5/8 5/8 5/8 7/8
22 22 22 27 27 29 29 29 22 22 22 22 27 27 27 27 27 29 29 27 27 27 27
17 17 17 21 21 28 28 28 17 17 17 17 21 21 21 28 28 28 28 21 21 21 21
14 14 14 22 22 25 25 25 14 14 14 14 22 22 22 22 22 25 25 22 22 22 22
77 92 92 136 141 174 196 221 98 98 103 107 148 148 152 172 182 183 207 114 114 120 136
ZWN Scroll® Compressor Model ZWN Model
Compressor
ZWN030X6 ZWN035X6 ZWN045X6 ZWN055X6 ZWN060X6 ZWN030L6 ZWN035L6 ZWN045L6 ZWN055L6 ZWN060L6
ZS21K4E ZS26K4E ZS30K4E ZS38K4E ZS45K4E ZF09K4E ZF11K4E ZF13K4E ZF15K4E ZF18K4E
Refrigerant
Suction Temp
Extended Temp R-404A/ R-507
10° F
Low Temp R-404A/ R-507
-10° F
Capacity* BTUH 19,740 24,490 28,480 34,970 41,850 13,200 16,200 19,100 23,300 27,700
Air Defrost Total MCA 208-230/ 1/60 18.4 23.2 30 36 18 23 30 36 -
208-230/ 3/60 15 15.2 17 24 27 15 15 17 24 27
Connections (in.) ODS 460/ 3/60 15 15 15 15 15 15 15 15 15 15
Dimensions (in.)
Liquid
Suction
L
H
D
Approx. Net Wt. (lbs.)
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8
29 29 29 29 29 27 27 27 27 29
28 28 28 28 28 28 28 28 28 28
25 25 25 25 25 22 22 22 22 25
171 186 207 226 241 159 165 185 201 207
† Only for use with R-404A * Capacity rating conditions based on: 85°F Entering Water, 105°F Condensing Temperature, 20°F ITD (ITD= condensing temperature - entering condenser water temperature), 0°F Subcooling.
21
Condensing Units 3/4 - 22 HP Indoor Water-Cooled Condensing Units Model SWN
are “vessel-mounted” indoor water-cooled condensing units, complete with a shell and tube. The cleanable water-cooled condenser is perfect for applications where air cooled condensers would not be practical, or water is readily available. Available in sizes 3/4 - 22 HP in all temperature ranges, the SWN units are an economical, compact selection.
Model SWN SWN Model
Compressor
SWN0075H2 SWN0075M2 SWN0090H2 SWN0100H2 SWN0150H2 SWN0200H2 SWN0200M2 SWN0300H2 SWN0400H2 SWN0499H2 SWN0500H2 SWN0750H2 SWN0760H2 SWN0761H2 SWN1000H2 SWN1500H2 SWN2000H2 SWN0090M6 SWN0199M6 SWN0200M6 SWN0310M6 SWN0500M6 SWN0150L6 SWN0200L6 SWN0210L6 SWN0310E6 SWN0310L6 SWN0311L6 SWN0400L6 SWN0599L6 SWN0600L6 SWN0601L6 SWN0750L6 SWN0900L6 SWN1000L6 SWN1500L6 SWN2200L6
KAN10075 KAE10075 KARA010E KAM10100 KAGA0150 ERA10200 ERC10200 ERF10311 NRB20400 2DC3R53KE 2DD3R63KE 2DL3R78KE 2DA3R89KE 3DA3R10ME 3DB3R12ME 3DS3R17ME 4DA3R18ME KARA010E KAKA020E ERCA021E ERFA031E 2DC3R53KE KALA016E EADA020E EAVA021E LACA032E LAHA032E 2DF3F16KE 2DL3F20KE 2DA3F23KE 2DB3F25KE 3DA3F28KE 3DB3F33KE 3DF3F40KE 3DS3F46KE 4DL3F63KE 4DT3F76KE
Refrig.
Suction Capacity* Temp (BTUH)
Medium & High Temp R-22
25ºF
Medium Temp R-404A/ R-507
20ºF
Low Temp R-404A/ R-507
-20ºF
6,700 8,000 9,370 10,690 12,150 16,090 19,480 28,290 40,130 46,230 53,810 67,750 76,770 92,810 110,190 146,060 156,830 9,140 15,120 19,430 28,090 43,470 6,830 7,770 8,820 18,060 14,180 19,950 24,260 27,930 29,930 33,600 39,800 48,620 55,020 75,390 90,720
Air Defrost (Total MCA)
Dimensions (in.)
230/ 1/60
208-230/ 3/60
460/ 3/60
Liquid
Suction
L
H
D
Approx. Net Wt. (lbs.)
15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.0 -
15.0 15.0 20.0 20.0 15.0 20.0 20.0 28.7 -
15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 24.4 25.0 25.0 35.4 35.9 46.0 48.9 66.9 65.9 15.0 15.0 15.0 15.0 25.0 15.0 15.0 15.0 15.0 15.0 20.0 29.5 32.3 31.7 30.0 34.5 41.5 46.5 59.0 74.0
15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.0 20.0 22.4 22.4 29.5 32.9 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.0 20.0 20.8 29.5 37.0
3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 5/8 5/8 5/8 5/8 5/8 7/8 7/8 7/8 3/8 3/8 3/8 1/2 5/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 7/8 7/8 7/8
5/8 5/8 5/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8 7/8 7/8 7/8 1-1/8 1-3/8 7/8 7/8 7/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8 2-1/8 2-1/8
3-3/4 3-3/4 3-3/4 3-3/4 3-3/4 3-3/4 3-3/4 26-3/4 26-3/4 30-1/3 30-1/3 35-1/3 35-1/3 35-1/3 35-1/3 35-1/3 35-1/3 23-3/4 23-3/4 23-3/4 26-3/4 30-1/3 23-3/4 23-3/4 23-3/4 26-3/4 26-3/4 26-3/4 26-3/4 30-1/3 30-1/3 30-1/3 35-1/3 35-1/3 35-1/3 35-1/3 35-1/3
37-1/3 37-1/3 37-1/3 37-1/3 37-1/3 37-1/3 37-1/3 36-1/3 36-1/3 39-1/4 39-1/4 41-1/2 41-1/2 41-1/2 41-1/2 41-1/2 41-1/2 37-1/3 37-1/3 37-1/3 36-1/3 39-1/4 37-1/3 37-1/3 37-1/3 36-1/3 36-1/3 36-1/3 36-1/3 39-1/4 39-1/4 39-1/4 41-1/2 41-1/2 41-1/2 41-1/2 41-1/2
33 33 33 33 33 33 33 38-1/3 38-1/3 42-1/2 42-1/2 55-1/2 55-1/2 55-1/2 55-1/2 55-1/2 55-1/2 33 33 33 38-1/3 42-1/2 33 33 33 38-1/3 38-1/3 38-1/3 38-1/3 42-1/2 42-1/2 42-1/2 55-1/2 55-1/2 55-1/2 55-1/2 55-1/2
165 165 180 180 195 260 260 325 385 400 400 465 465 465 715 735 795 180 210 260 325 400 195 325 325 325 325 340 385 415 415 430 465 560 715 780 865
* Capacity based on 85°F Entering Water, 105°F Condensing Temperature, 5°F Subcooling.
22
Connections (in.)
208-230/ 1/60
Condensing Units 3/4 - 22 HP Remote Indoor Compressor Condensing Units Model SRN are indoor compressor units designed for use with a remote air-cooled or evaporative condenser. Typical applications include supermarkets, warehouses, convenience stores or wherever outdoor roof or pad space is at a minimum. SRN units are available in sizes 3/4 - 22 HP in high, medium and low temperature.
Model SRN SRN Model
Compressor
SRN0075H2 SRN0075M2 SRN0090H2 SRN0100H2 SRN0150H2 SRN0200H2 SRN0200M2 SRN0300H2 SRN0400H2 SRN0499H2 SRN0500H2 SRN0750H2 SRN0760H2 SRN0761H2 SRN1000H2 SRN1500H2 SRN2000H2 SRN0090M6 SRN0199M6 SRN0200M6 SRN0310M6 SRN0500M6 SRN0150L6 SRN0200L6 SRN0210L6 SRN0310E6 SRN0310L6 SRN0311L6 SRN0400L6 SRN0599L6 SRN0600L6 SRN0601L6 SRN0750L6 SRN0900L6 SRN1000L6 SRN1500L6 SRN2200L6
KAN10075 KAE10075 KARA010E KAM10100 KAGA0150 ERA10200 ERC10200 ERF10311 NRB20400 2DC3R53KE 2DD3R63KE 2DL3R78KE 2DA3R89KE 3DA3R10ME 3DB3R12ME 3DS3R17ME 4DA3R18ME KARA010E KAKA020E ERCA021E ERFA031E 2DC3R53KE KALA016E EADA020E EAVA021E LACA032E LAHA032E 2DF3F16KE 2DL3F20KE 2DA3F23KE 2DB3F25KE 3DA3F28KE 3DB3F33KE 3DF3F40KE 3DS3F46KE 4DL3F63KE 4DT3F76KE
Refrig.
Suction Capacity* Temp (BTUH)
Medium & High Temp R-22
25ºF
Medium Temp R-404A/ R-507
20ºF
Low Temp R-404A/ R-507
-20ºF
5,970 7,110 8,360 9,580 10,920 13,100 17,260 25,580 35,260 41,290 48,320 61,380 69,680 84,740 101,120 134,160 143,520 7,780 12,850 16,310 24,080 37,370 6,470 7,310 8,270 17,070 13,250 19,080 23,110 26,710 28,620 32,330 38,370 46,850 52,890 72,720 86,710
Air Defrost (Total MCA) 208-230/ 208-230/ 230/1/60 1/60 3/60 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.0 15.0 24.4 25.0 25.0 35.4 35.9 46.0 48.9 66.9 65.9 15.0 15.0 15.0 15.0 15.0 20.0 15.0 25.0 15.0 15.0 15.0 15.0 20.0 15.0 20.0 15.0 20.0 15.0 28.7 20.0 29.5 32.3 31.7 30.0 34.5 41.5 46.5 59.0 74.0
Connections (in.) 460/ 3/60 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.0 20.0 22.4 22.4 29.5 32.9 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 20.0 20.0 20.8 29.5 37.0
Dimensions (in.)
Liquid
Suction
L
H
D
3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 5/8 5/8 5/8 5/8 5/8 7/8 7/8 7/8 3/8 3/8 3/8 1/2 5/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 7/8 7/8 7/8
5/8 5/8 5/8 7/8 7/8 7/8 7/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8 7/8 7/8 7/8 1-1/8 1-3/8 7/8 7/8 7/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 1-5/8 1-5/8 2-1/8 2-1/8
23-3/4 23-3/4 23-3/4 23-3/4 23-3/4 23-3/4 23-3/4 26-3/4 26-3/4 30-1/3 30-1/3 35-1/3 35-1/3 35-1/3 35-1/3 35-1/3 35-1/3 23-3/4 23-3/4 23-3/4 26-3/4 30-1/3 23-3/4 23-3/4 23-3/4 26-3/4 26-3/4 26-3/4 26-3/4 30-1/3 30-1/3 30-1/3 35-1/3 35-1/3 35-1/3 35-1/3 35-1/3
36-1/3 36-1/3 36-1/3 36-1/3 36-1/3 36-1/3 36-1/3 39-1/4 39-1/4 39-1/4 39-1/4 43-1/2 43-1/2 43-1/2 43-1/2 43-1/2 43-1/2 36-1/3 36-1/3 36-1/3 39-1/4 39-1/4 36-1/3 36-1/3 36-1/3 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 39-1/4 43-1/2 43-1/2 43-1/2 43-1/2 43-1/2
35 35 35 35 35 35 35 40 40 42-1/2 42-1/2 47 47 47 47 47 47 35 35 35 40 42-1/2 35 35 35 40 40 40 40 42-1/2 42-1/2 42-1/2 47 47 47 47 47
Approx. Net Wt. (lbs.) 155 155 160 160 175 245 245 305 360 375 375 385 385 385 595 615 665 155 200 245 305 375 175 305 305 305 305 320 360 390 390 405 385 520 650 710 725
* Based on 110°F Condensing Temperature, 6°F Subcooling for Low Temp models and 120°F Condensing Temperature, 8°F Subcooling for Medium & High Temp models.
23
Air-Cooled Condensers 1 - 26 Tons Air-Cooled Condensers Model WSS air-cooled condensers are designed for efficient performance and low maintenance.
The units feature an aluminum cabinet for long life and attractive appearance. The aluminum fin, copper tube coils have staggered tube design for high efficiency. All coils are dehydrated, pressure tested, sealed with caps and pressurized for shipment. PSC motors come standard to help you save energy.
Model WSS WSS Model WSS008 WSS009 WSS010 WSS016 WSS024 WSS040 WSS049 WSS061 WSS070 WSS080 WSS105 WSS113 WSS133
Total Heat Rejection 30ºF TD R-404A, R-22 507 22.9 22.4 26.7 26.2 30.5 29.9 47.1 46.2 73.0 71.5 120.0 117.6 146.0 143.1 182.4 178.8 209.6 205.5 239.6 234.8 314.2 307.9 339.6 332.8 398.2 390.2
208/230/460/3/60 1140 RPM available
24
CFM
Motor HP (1)
FLA 208/230/60/1
2,400 2,400 2,400 2,100 5,050 6,450 10,100 12,400 13,700 12,900 20,500 19,900 19,400
1/4 1/4 1/4 1/4 1/3 1/2 (2) 1/3 (2) 1/2 (2) 1/2 (2) 1/2 (3) 1/2 (3) 1/2 (3) 1/2
2.0 2.0 2.0 2.0 3.4 3.9 6.8 7.8 7.8 7.8 11.7 11.7 11.7
Dimensions (in.)
Connections (in.)
L
H
D
Inlet
Outlet
Approx. Net Wt. (lbs.)
37-1/2 37-1/2 37-1/2 37-1/2 39-3/4 49-3/4 69-3/4 69-3/4 89-3/4 89-3/4 129-3/4 129-3/4 129-3/4
22 22 22 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2
43 43 43 43 43 43 43 43 43 43 43 43 43
3/8 5/8 7/8 7/8 1-1/8 1-1/8 (2) 1-1/8 (2) 1-1/8 (2) 1-1/8 (2) 1-3/8 (2) 1-5/8 (2) 1-5/8 (2) 1-5/8
3/8 5/8 5/8 5/8 7/8 7/8 (2) 7/8 (2) 7/8 (2) 7/8 (2) 1-1/8 (2) 1-1/8 (2) 1-1/8 (2) 1-1/8
96 96 96 114 180 260 450 470 510 530 550 580 625
Air-Cooled Condensers Models HNE, HNQ, HNX, HNL and HNH Air-Cooled Condensers EC and 830/540
series air-cooled condensers feature improved energy efficiency and low sound levels, which are key features sought by the supermarket and grocery industry. Traditional condensers using 1140 RPM motors offer high capacities, but cannot meet the low sound and energy efficiency standards demanded today by this industry. Now, Chandler brings the best of both worlds together with advanced solutions that offer high capacities for operation, while meeting the low sound and energy efficiency requirements you demand.
Model HNE with EC motor technology offers all the benefits of variable speed motors without the complexity. EC motors utilize variable-speed technology, which optimizes fan speeds for load requirements, maximizes energy efficiency and minimizes sound.
Models HNQ, HNX, and HNL features Chandler’s patented QuietEdge™ technology that uses specially designed swept fan blades to reduce noise levels. These blades are uniquely designed for each motor speed, optimizing performance and ensuring you’re receiving the lowest sound levels possible. Look for the QuietEdge™ 4 blade on the 540 RPM motors and the QuietEdge™ 5 on the 830 RPM motors.
Model HNH continues to offer Chandler’s 1140 RPM series for customers seeking the most economical solution for their capacity requirements.
EC Series Model HNE, 2.2 kW, 31.5" Fan Diameter THR, MBH/1°F TD
Total FLA
HNE Model
R-22
R-404A
HNES01A008 HNES01A009 HNES02A011 HNES02A015 HNES02A018 HNES03A023 HNES03A027 HNES04A031 HNES04A036 HNES05A039 HNES05A047 HNES06A056 HNES07A065
7.7 9.3 11.3 15.4 18.1 23.1 27.2 30.8 36.3 39.3 46.6 56.0 64.6
7.6 9.1 11.1 15.1 17.8 22.7 26.7 30.2 35.5 38.5 45.7 54.8 63.3
11,000 10,500 23,400 22,000 20,900 33,100 31,400 42,600 40,000 53,200 50,000 60,000 70,000
7.0 7.0 14.0 14.0 14.0 21.0 21.0 28.0 28.0 35.0 35.0 42.0 49.0
HNED04A023 HNED04A031 HNED04A036 HNED06A046 HNED06A054 HNED08A062 HNED08A073 HNED10A079 HNED10A093 HNED12A112 HNED14A129
22.7 30.8 36.3 46.2 54.4 61.7 72.5 78.6 93.3 111.9 129.2
22.2 30.2 32.5 45.3 53.3 60.5 71.1 77.0 91.4 109.7 126.7
46,700 44,100 41,800 66,100 62,700 85,100 80,000 106,400 100,100 120,100 140,100
28.0 28.0 28.0 42.0 42.0 56.0 56.0 70.0 70.0 84.0 98.0
CFM
230/3/60
460/3/60
Single Row 3.5 3.5 7.0 7.0 7.0 10.5 10.5 14.0 14.0 17.5 17.5 21.0 24.5 Double Row 14.0 14.0 14.0 21.0 21.0 28.0 28.0 35.0 35.0 42.0 49.0
Maximum No. of Feeds
Connections (in.)
Refrigerant Summer Charge R-22 (lbs.)
Approx. Net Wt. (lbs.)
7 14 14 21 28 21 28 21 28 21 28 28 28
1-3/8 1-3/8 1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 (2) 2-5/8
8 10 10 15 29 22 30 51 70 64 86 102 118
330 360 590 640 690 930 1,010 1,220 1,320 1,520 1,650 1,960 2,260
28 42 56 42 56 42 56 42 56 56 56
(2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (4)
19 29 40 44 58 104 140 125 172 201 236
1,290 1,390 1,490 2,060 2,210 2,730 2,930 3,410 3,660 4,370 5,070
1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 2-5/8
Bold indicates standard model capacity at 10 FPI
EC Series 830/540 Series
25
Air-Cooled Condensers 540 Series Model HNQ, 540 RPM, 0.5 HP, 30" Fan Diameter HNQ Model
THR, MBH/1°F TD
Total FLA CFM
R-22
R-404A
230/3/60
HNQS01A005 HNQS01A006 HNQS02A008 HNQS02A010 HNQS02A011 HNQS03A016 HNQS03A017 HNQS04A021 HNQS04A023 HNQS05A026 HNQS05A029 HNQS06A034 HNQS07A042
5.2 6.1 8.0 10.3 11.5 15.6 17.2 20.7 22.9 25.9 28.6 34.4 41.6
5.1 5.9 7.8 10.1 11.2 15.2 16.9 20.3 22.4 25.4 28.1 33.7 40.7
5,400 5,200 11,200 10,800 10,400 16,100 15,600 21,500 20,800 26,900 26,000 31,200 36,400
3.5 3.5 7.0 7.0 7.0 10.5 10.5 14.0 14.0 17.5 17.5 21.0 24.5
HNQD04A016 HNQD04A021 HNQD04A023 HNQD06A031 HNQD06A034 HNQD08A041 HNQD08A046 HNQD10A052 HNQD10A057 HNQD12A069 HNQD14A083
16.0 20.7 22.9 31.0 34.4 41.4 45.8 51.8 57.3 68.7 83.1
15.6 20.3 22.4 30.4 33.7 40.6 44.9 50.7 56.1 67.3 81.5
22,300 21,500 20,800 32,300 31,200 43,000 41,600 53,700 52,100 62,500 72,900
14.0 14.0 14.0 21.0 21.0 28.0 28.0 35.0 35.0 42.0 49.0
460/3/60
Single Row 1.8 1.8 3.5 3.5 3.5 5.3 5.3 7.0 7.0 8.8 8.8 10.5 12.3 Double Row 7.0 7.0 7.0 10.5 10.5 14.0 14.0 17.5 17.5 21.0 24.5
Maximum No. of Feeds
Connections (in.)
Refrigerant Summer Charge R-22 (lbs.)
Approx. Net Wt. (lbs.)
7 14 14 21 28 21 28 21 28 21 28 28 28
1-3/8 1-3/8 1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 (2) 2-5/8
8 10 10 15 29 22 30 51 70 64 86 102 118
330 360 580 630 680 930 1,000 1,210 1,310 1,510 1,640 1,950 2,240
28 42 56 42 56 42 56 42 56 56 56
(2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (4)
19 29 40 44 58 104 140 125 172 201 236
1,240 1,340 1,440 1,990 2,140 2,630 2,830 3,290 3,540 4,230 4,910
1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 2-5/8
Bold indicates standard model capacity at 10 FPI
830 Series Model HNX, 830 RPM, 1.0 HP, 30" Fan Diameter HNX Model
THR, MBH/1°F TD R-22
R-404A
HNXS01A006 HNXS01A008 HNXS02A010 HNXS02A013 HNXS02A015 HNXS03A020 HNXS03A023 HNXS04A026 HNXS04A030 HNXS05A033 HNXS05A038 HNXS06A045 HNXS07A052
6.4 7.5 9.8 13.1 15.1 19.7 22.7 26.3 30.3 32.8 37.8 45.4 52.0
6.2 7.4 9.6 12.8 14.8 19.3 22.3 25.7 29.7 32.1 37.1 44.5 51.0
7,600 7,300 15,900 15,200 14,700 22,900 22,000 29,800 28,400 37,300 35,500 42,600 49,700
4.8 4.8 9.6 9.6 9.6 14.4 14.4 19.2 19.2 24.0 24.0 28.8 33.6
HNXD04A020 HNXD04A026 HNXD04A030 HNXD06A039 HNXD06A045 HNXD08A052 HNXD08A061 HNXD10A066 HNXD10A076 HNXD12A091 HNXD14A104
19.6 26.2 30.3 39.4 45.4 52.5 60.6 65.6 75.7 90.8 104.1
19.2 25.7 29.7 38.6 44.5 51.4 59.3 64.3 74.2 89.0 102.0
31,700 30,500 29,300 45,700 44,000 59,700 56,800 74,600 71,000 85,200 99,400
19.2 19.2 19.2 28.8 28.8 38.4 38.4 48.0 48.0 57.6 67.2
Bold indicates standard model capacity at 10 FPI
26
Total FLA CFM 230/3/60
460/3/60
Single Row 2.4 2.4 4.8 4.8 4.8 7.2 7.2 9.6 9.6 12.0 12.0 14.4 16.8 Double Row 9.6 9.6 9.6 14.4 14.4 19.2 19.2 24.0 24.0 28.8 33.6
Maximum No. of Feeds
Connections (in.)
Refrigerant Summer Charge R-22 (lbs.)
Approx. Net Wt. (lbs.)
7 14 14 21 28 21 28 21 28 21 28 28 28
1-3/8 1-3/8 1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 (2) 2-5/8
8 10 10 15 29 22 30 51 70 64 86 102 118
330 360 580 630 680 930 1,000 1,210 1,310 1,510 1,640 1,950 2,240
28 42 56 42 56 42 56 42 56 56 56
(2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (4)
19 29 40 44 58 104 140 125 172 201 236
1,240 1,340 1,440 1,990 2,140 2,630 2,830 3,290 3,540 4,230 4,910
1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 2-5/8
Air-Cooled Condensers 830 Series Model HNL, 830 RPM, 1.5 HP, 30" Fan Diameter THR, MBH/1°F TD
Total FLA
HNL Model
R-22
R-404A
HNLS01A007 HNLS01A008 HNLS02A010 HNLS02A014 HNLS02A016 HNLS03A021 HNLS03A024 HNLS04A028 HNLS04A032 HNLS05A035 HNLS05A042 HNLS06A050 HNLS07A055
6.7 8.0 10.1 13.9 16.1 20.9 24.2 27.8 32.3 35.5 41.6 49.9 55.0
6.6 7.8 9.9 13.6 15.8 20.5 23.8 27.3 31.7 34.7 40.8 48.9 53.9
8,400 8,000 17,500 16,700 16,100 25,100 24,100 32,800 31,200 41,000 39,100 46,900 54,700
6.6 6.6 13.2 13.2 13.2 19.8 19.8 26.4 26.4 33.0 33.0 39.6 46.2
HNLD04A020 HNLD04A028 HNLD04A032 HNLD06A042 HNLD06A048 HNLD08A056 HNLD08A065 HNLD10A071 HNLD10A083 HNLD12A100 HNLD14A110
20.2 27.8 32.3 41.8 48.4 55.7 64.6 70.9 83.1 99.8 110.0
19.8 27.3 31.7 40.9 47.5 54.6 63.3 69.5 81.5 97.8 107.9
35,000 33,500 32,100 50,200 48,200 65,600 62,500 82,000 78,100 93,700 109,300
26.4 26.4 26.4 39.6 39.6 52.8 52.8 66.0 66.0 79.2 92.4
CFM
Maximum No. of Feeds 230/3/60 460/3/60 575/3/60 Single Row 3.3 3.3 6.6 6.6 6.6 9.9 9.9 13.2 13.2 16.5 16.5 19.8 23.1 Double Row 13.2 13.2 13.2 19.8 19.8 26.4 26.4 33.8 33.0 39.6 46.2
Connections (in.)
Refrigerant Summer Charge R-22 (lbs.)
Approx. Net Wt. (lbs.)
2.6 2.6 5.2 5.2 5.2 7.8 7.8 10.4 10.4 13.0 13.0 15.6 18.2
7 14 14 21 28 21 28 21 28 21 28 28 28
1-3/8 1-3/8 1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 (2) 2-5/8
8 10 10 15 29 22 30 51 70 64 86 102 118
330 360 580 630 680 930 1,000 1,210 1,310 1,510 1,640 1,950 2,240
10.4 10.4 10.4 15.6 15.6 20.8 20.8 26.0 26.0 31.2 36.4
28 42 28 56 56 42 56 42 56 56 56
(2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (4)
19 29 40 44 58 104 140 125 172 201 236
1,240 1,340 1,440 1,990 2,140 2,630 2,830 3,290 3,540 4,230 4,910
Connections (in.)
Refrigerant Summer Charge R-22 (lbs.)
Approx. Net Wt. (lbs.)
1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 2-5/8
Bold indicates standard model capacity at 10 FPI
1140 Series Model HNH, 1140 RPM, 1.5 HP, 30" Fan Diameter THR, MBH/1°F TD
Total FLA
HNH Model
R-22
R-404A
HNHS01A007 HNHS01A009 HNHS02A011 HNHS02A015 HNHS02A017 HNHS03A022 HNHS03A026 HNHS04A029 HNHS04A034 HNHS05A037 HNHS05A044 HNHS06A053 HNHS07A061
7.3 8.7 10.7 14.5 17.1 21.8 25.7 29.1 34.2 37.1 44.0 52.8 61.0
7.2 8.6 10.5 14.2 16.7 21.4 25.2 28.5 33.5 36.4 43.1 51.7 59.8
9,900 9,500 20,500 19,800 19,000 29,700 28,500 38,600 37,000 48,300 46,200 55,400 64,700
7.0 7.0 14.0 14.0 14.0 21.0 21.0 28.0 28.0 35.0 35.0 42.0 49.0
HNHD04A021 HNHD04A029 HNHD04A034 HNHD06A044 HNHD06A051 HNHD08A058 HNHD08A068 HNHD10A074 HNHD10A088 HNHD12A106 HNHD14A122
21.4 29.1 34.2 43.6 51.3 58.2 68.4 74.2 88.0 105.6 121.9
21.0 28.5 33.5 42.8 50.3 57.0 67.1 72.7 86.2 103.5 119.5
41,000 39,600 38,100 59,400 57,100 77,200 73,900 96,500 92,400 110,900 129,400
28.0 28.0 28.0 42.0 42.0 56.0 56.0 70.0 70.0 84.0 98.0
CFM
Maximum No. of Feeds 208/3/60 460/3/60 575/3/60 Single Row 3.5 3.5 7.0 7.0 7.0 10.5 10.5 14.0 14.0 14.0 17.5 17.5 21.0 Double Row 24.5 14.0 14.0 21.0 21.0 28.0 28.0 35.0 35.0 42.0 49.0
2.8 2.8 5.6 5.6 5.6 8.4 8.4 11.2 11.2 14.0 14.0 16.8 19.6
7 14 14 21 28 21 28 21 28 21 28 28 28
1-3/8 1-3/8 1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 (2) 2-5/8
8 10 10 15 29 22 30 51 70 64 86 102 118
330 360 580 630 680 930 1,000 1,210 1,310 1,510 1,640 1,950 2,240
11.2 11.2 11.2 16.8 16.8 22.4 22.4 28.0 28.0 33.6 39.2
28 42 56 42 56 42 56 42 56 56 56
(2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (4)
19 29 40 44 58 104 140 125 172 201 236
1,240 1,340 1,440 1,990 2,140 2,630 2,830 3,290 3,540 4,230 4,910
1-3/8 1-5/8 2-1/8 2-1/8 2-1/8 2-1/8 2-5/8 2-5/8 2-5/8 2-5/8 2-5/8
Bold indicates standard model capacity at 10 FPI
27
Fluid Coolers Direct-Drive Fluid Coolers Model WGS (vertical or horizontal air flow available) and HFS (available in vertical air flow only) direct-drive fluid coolers are easy to install and maintain, yet are ruggedly designed to handle all applications. Available in a variety of sizes, the WGS and HFS units have design features ideal for the commercial/industrial locations. Specifically engineered for outdoor installations, the cabinet is constructed of heavy gauge aluminum or prepainted galvanized steel to resist corrosion in all climates Additional design features include: • Fully baffled fan sections to prevent windmilling • Single-point wiring to junction box • Balanced fans, featuring heavy gauge aluminum blades riveted to plated steel spiders
Model WGS WGS Model
CFM
WGS049 WGS080 WGS107 WGS123 WGS147 WGS165 WGS211 WGS225 WGS248
5,050 6,450 10,100 12,400 13,700 12,900 20,500 19,900 19,400
Vol. in Gal. 3 4 4 4 5 6 7 7 9
Base Capacity Range 1°F TD, 40% Glycol (130° Average Temp.) Minimum Maximum GPM MBH PD/F GPM MBH PD/F 10 2.23 4.7 30 2.97 15.5 10 3.07 7.4 60 4.62 13.0 10 3.46 7.5 60 6.10 28.2 10 3.62 7.5 60 6.88 28.2 10 3.92 9.4 50 7.64 25.2 10 4.17 12.4 60 8.70 20.9 15 5.93 12.3 120 12.31 25.7 20 6.99 6.8 120 12.94 25.7 20 7.65 12.9 160 14.08 25.7
Motor Qty.
HP
1 1 2 2 2 2 3 3 3
1/3 1/3 1/3 1/3 1/3 1/3 1/3 1/3 1/3
Dimensions (in.)
208-230V L 3 Ph. 2.6 40 2.6 50 5.2 70 5.2 70 5.2 90 2.5 90 7.8 130 7.8 130 7.8 130
H
D
40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2 40-1/2
43 43 43 43 43 43 43 43 43
Connections (in.) Approx. Dry Net Wt. Inlet Outlet (lbs.) 1-3/8 1-3/8 180 1-5/8 1-5/8 260 2-1/8 2-1/8 450 2-1/8 2-1/8 470 2-1/8 2-1/8 510 2-1/8 2-1/8 530 2-5/8 2-5/8 550 2-5/8 2-5/8 580 2-5/8 2-5/8 625
*Motors also available in 208-230/1, 460/3
Model HFS HFS Model
CFM
Operating Charge (Gal.)
HFS113 HFS133 HFS149 HFS175 HFS199 HFS223 HFS247 HFS265 HFS297 HFS331 HFS351 HFS377 HFS401 HFS443 HFS481 HFS583
19,780 19,800 19,110 18,340 29,700 28,660 28,070 38,600 37,250 38,020 35,710 46,610 46,200 44,580 55,400 53,460
6.6 9.0 9.0 11.6 12.8 12.8 16.4 16.4 16.4 21.3 21.3 20.0 26.1 26.1 31.0 31.0
HFS226 39,570 13.3 HFS266 39,600 18.2 HFS298 38,210 18.2 HFS330 37,530 23.1 HFS350 36,770 23.1 HFS398 59,400 25.4 HFS428 58,510 25.4 HFS448 57,320 25.4 HFS496 56,240 32.8 HFS532 77,200 32.7 HFS596 74,500 32.7 HFS660 72,790 42.5 HFS700 71,310 42.5 HFS754 93,120 40.0 HFS804 92,400 52.1 HFS842 91,010 52.1 HFS888 89,170 52.1 HFS964 110,900 62.0 HFS986 109,240 62.0 HFS998 107,020 62.0 † Does not include operating charge
28
Base Capacity Range @ 1°F TD 40% Motor (Total FLA) Glycol (130° Average Temp.) Minimum Maximum 208575/ Qty. HP 230/3/60 3/60 GPM MBH PD/F GPM MBH PD/F Single Row 20 6.4 3.2 120 11.69 10.7 2 1-1/2 14.0 5.6 20 7.01 4.8 180 13.34 10.7 2 1-1/2 14.0 5.6 20 7.42 4.8 180 14.89 10.7 2 1-1/2 14.0 5.6 30 10.2 6.6 240 16.79 10.7 2 1-1/2 14.0 5.6 20 8.19 7.0 180 19.40 15.7 3 1-1/2 21.0 8.4 30 11.62 14.3 180 21.66 15.7 3 1-1/2 21.0 8.4 30 11.92 9.5 240 23.74 15.7 3 1-1/2 21.0 8.4 20 8.71 9.2 180 25.09 20.8 4 1-1/2 28.0 11.2 30 12.34 6.1 180 27.93 20.8 4 1-1/2 28.0 11.2 30 12.88 12.5 240 30.89 20.8 4 1-1/2 28.0 11.2 30 13.04 12.5 240 32.13 20.8 4 1-1/2 28.0 11.2 30 12.97 7.5 180 33.69 25.8 5 1-1/2 35.0 14.0 30 13.20 15.4 240 35.89 25.8 5 1-1/2 35.0 14.0 30 13.40 15.4 240 39.12 25.8 5 1-1/2 35.0 14.0 40 17.22 8.9 220 41.02 26.4 6 1-1/2 42.0 16.8 40 17.59 8.9 220 44.66 26.4 6 1-1/2 42.0 16.8 Double Row 30 11.24 6.6 240 23.38 10.7 4 1-1/2 28.0 11.2 40 14.03 4.8 350 26.56 10.2 4 1-1/2 28.0 11.2 40 14.84 4.8 350 29.65 10.2 4 1-1/2 28.0 11.2 50 17.77 4.8 500 32.53 11.5 4 1-1/2 28.0 11.2 50 18.21 4.8 500 33.80 11.5 4 1-1/2 28.0 11.2 40 16.38 7.0 350 38.66 15.0 6 1-1/2 42.0 16.8 40 16.69 7.0 350 40.99 15.0 6 1-1/2 42.0 16.8 40 16.93 7.0 350 43.06 15.0 6 1-1/2 42.0 16.8 50 20.73 6.9 500 47.77 16.9 6 1-1/2 42.0 16.8 40 17.42 9.2 350 49.87 19.8 8 1-1/2 56.0 22.4 40 17.74 9.2 350 55.46 19.8 8 1-1/2 56.0 22.4 50 21.96 9.0 500 62.24 22.3 8 1-1/2 56.0 22.4 50 22.13 9.0 500 64.74 22.3 8 1-1/2 56.0 22.4 60 25.94 7.5 350 66.82 24.5 10 1-1/2 70.0 28.0 50 22.23 11.2 500 72.42 27.7 10 1-1/2 70.0 28.0 50 22.45 11.2 500 75.91 27.7 10 1-1/2 70.0 28.0 80 34.06 7.5 500 78.96 27.7 10 1-1/2 70.0 28.0 80 34.44 8.9 500 84.70 33.1 12 1-1/2 84.0 33.6 80 34.86 8.9 500 88.78 33.1 12 1-1/2 84.0 33.6 80 35.17 8.9 500 92.33 33.1 12 1-1/2 84.0 33.6
Dimensions (in.) 460/ 3/60
L
H
D
Approx. Net Wt. (lbs.)†
7.0 7.0 7.0 7.0 10.5 10.5 10.5 14.0 14.0 14.0 14.0 17.5 17.5 17.5 21.0 21.0
127 127 127 127 180 180 180 233 233 233 233 286 286 286 339 339
50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50
45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2 45-1/2
720 760 780 860 1,170 1,190 1,220 1,550 1,590 1,620 1,730 1,960 1,960 2,200 2,350 2,580
14.0 14.0 14.0 14.0 14.0 21.0 21.0 21.0 21.0 28.0 28.0 28.0 28.0 35.0 35.0 35.0 35.0 42.0 42.0 42.0
127 127 127 127 127 180 180 180 180 233 233 233 233 286 286 286 286 339 339 339
50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50
88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88 88
1,560 1,600 1,650 1,670 1,780 2,350 2,400 2,500 2,560 3,080 3,140 3,190 3,450 3,920 3,930 4,070 4,300 4,620 4,800 5,130
Refrigeration Controls and Technology Beacon II™ Refrigeration System is Chandler’s patented, pre-assembled, factory-installed refrigeration system featuring an integrated microcomputer-based electronic control board. Beacon II™ offers: • Complete factory installation, wiring and testing, saving time and money • Simplified field electrical connections and 24 volt wiring between condenser and evaporator coil • Preset factory superheat allows the system to run more efficiently and reduces future adjustments • Monitors and controls box temperature, evaporator superheat, system status and defrost • Monitor and make system changes remotely via modem with exclusive Beacon II™ Smart II software with Beacon II™ Smart Controller • Data-logging capabilities with Smart Controller
™
Beacon II™ Smart Controller allows you to monitor and make changes to the refrigeration system
via modem connection from anywhere in the world. One Smart Controller can program and control up to four condensing units with up to four evaporators on each system.
The patented Beacon II™ Smart Defrost system available with Beacon II™ Smart Controller can reduce the number of system defrost by 75 percent on average, greatly reducing the amount of energy used and reducing operating costs.
Beacon II™ Smart II Software makes it easy to adjust and monitor one or more refrigeration systems
as well as capture minute-by-minute system conditions. This Windows®-based software allows you to connect to the Beacon II™ Smart Controller from anywhere in the world to monitor the systems, make adjustments and log real-time system conditions. This data-logging capability is critical in the food-service industry.
Smart Defrost Kit™ (SDK), available as a factory installed option on condensing units or as an
aftermarket retrofit kit via Interlink Commercial Refrigeration Parts, is a control module that can reduce the number of defrosts by up to 40% on a typical commercial refrigeration system. This reduces energy consumption and costs.
29
Additional Products from Chandler
The Mohave advanced hot gas defrost refrigeration system with electronic controller utilizes hot gas to greatly reduce defrost times and operates in all outdoor ambient temperatures.* This leads to increased energy efficiency and product integrity in a refrigeration system that can be used in a greater variety of environmental conditions. This system utilizes a state-of-the-art electronic defrost controller with a proprietary control scheme that allows the system to continually operate at its most optimal level.
Condensing Unit
• Integral condenser sub-cooling circuit in condenser for added capacity and vapor free liquid • Floating Tube™ condenser coil design • Electronic defrost controller • Pressure or ambient fan cycling for head pressure control • Electronic pressure regulator for defrost control • Anti-short cycling protection • High pressure and low pressure controls • Oil pressure safety control • Easily accessible control box • High efficiency Copeland Discus® compressors with poe oil • Thermally protected permanently lubricated ball bearing condenser fan motor(s) • Receivers are sized for sufficient pumpdown capacity with inlet and outlet service valves • Cabinet is constructed from painted galvanized steel • Replaceable core liquid line filter drier • Replaceable core suction filter
Evaporators
• All components are factory installed and wired • Independent or single point power supply from condensing unit • 4 and 6 FPI medium and large unit coolers
Features: • • • • •
Mounted TXV and distributor nozzle Mounted check valves Mounted liquid line solenoid Mounted suction “P” trap Electric drain pan heater standard (mounted hot gas drain loop optional) • Mounted and wired control contactors
*Tested to -20°F ambient.
Multiple Compressor Condensing Units The FlexPack™ provides many features that produce outstanding results for both your refrigeration system and your bottom line. Flexibility for a wide range of applications • Modular design accommodates up to three compressors (0.5-6 HP Hermetic or Scroll®) • System capacity range from 5 – 18 HP (dependent upon cabinet size) Durability and Reliability • 14-gauge galvanized steel frame • 1-year parts warranty • 4-year optional compressor warranty Reduced installation costs and easy serviceability • Hinged access panels to refrigeration and electrical components • Single roof penetration • Single-point main power • Clean and intuitive electrical and piping layout Energy efficiency and reduced noise • Remote condenser circuits • Reduces heat load into space resulting in lower air conditioning energy costs • Recessed, vertical-discharge, flush-mounted 18" fans with 1100 RPM motors • Reduces noise levels
30
Clean and uniform appearance • Painted galvanized steel cabinet • Small footprint
(QJLQHHUHGSolutions
TM
)URP VWDUW WR ILQLVK
Air Handlers • Available in sizes 03-75 • Multiple coil types and accessories available to fit specific application needs • Engineered and built to fit your unique project requirements
Indoor and Outdoor Racks
• • • •
Available with up to 8 parallel-piped compressors Can be used with air-cooled, water-cooled or evaporative-cooled condensers Engineered and built to fit your unique project requirements ETL-508a listed control panel
Customer Specific Orders
We have a wide range of capabilities and will work with you, from start to finish, to create a customized solution for your needs. With Engineered Solutions, we will visualize, design, and realize the product required for the job. Contact your sales representative today to get the process started!
31
A Brand of Heatcraft Refrigeration Products, LLC 2175 West Park Place Blvd. • Stone Mountain, GA • 30087 800-321-1881 www.chandlerref.com CH-CC-0609 | Version 000
