Wireline Products Catalog

Revised: 2/12/2014

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Table of Contents Table of Contents .......................................................................................................... 1 Introduction ..................................................................................................................... 3 Mission Statement......................................................................................................... 3 TTS Field Services ............................................................................................................ 4 Workover / Completion Systems ............................................................................... 5 . TTS Tubing Patch Straddle Pack Installation ................................................................ 5 Product Information – Packers / Well Intervention ............................................. 7 Series 5011 Retrievable Dual Seal Bore Tubing Packer ................................................... 7 Series 5011 Retrievable Straddle Pack System ................................................................ 8 Series 5011 Retrievable Packer Accessories .................................................................... 9 Series 5011 Retrievable Packer Setting Assemblies....................................................... 10 Series 5014 Retrievable Bridge Plug (RBP) .................................................................... 11 Series 4800 Controlled Set High Expansion Packer ....................................................... 12 Series 4800 - Controlled Set High Expansion Cement Retainer ..................................... 13 Wireline Products......................................................................................................... 14 ACE Mix Cement Kits ...................................................................................................... 14 ACE Mix Cement (6 gallon) Kit Mixing Procedure ........................................................... 16 Series 9306 - Spiral Thru Tubing Bridge Plug ................................................................. 19 Series 7910 Electro-Hydraulic Bailer Bottom (EHBB) ..................................................... 20 Series 1000 Positive Displacement Bailer ....................................................................... 21 Series 8299 – Flex Bailer Segment ................................................................................. 22 Series 8300 - Gravity Bailer ............................................................................................ 23 Series 4010 - Wireline Pressure Setting Tool (Power Charge) ...................................... 29 Series 4020 - Hydrostatic Setting Tool (Non-Explosive).................................................. 30 Series 4200 - Fixed Slip Magna-Range Plug (Pressure Rated) ...................................... 31 Series 2105 - TTS Tubing Bridge Plug (10K) .................................................................. 32 Series 4250 - Cast Iron Bridge Plug ................................................................................ 33 Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

1

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Series 4260 - Cast Iron Cement Retainer ....................................................................... 34 Series 7850 - ACE Thru Tubing Umbrella Plug ............................................................... 35 Tech Unit - ACE Umbrella Plug ....................................................................................... 37 Series 1201 – Selective Release Tool............................................................................. 41 Series 1200 – Auto Release Tool .................................................................................... 42 TTS Rental Equipment .................................................................................................... 43

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

2

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Introduction Thru-Tubing Systems, Inc. (TTS) is an engineering, manufacturing, and service company specializing in thru-tubing workover, and completions. TTS offers retrievable dual seal bore, and permanent seal bore type thru-tubing packer systems. TTS has developed many innovative applications designed to allow the oil and gas operator to successfully conduct wellbore remedies using a coil tubing and/or wireline unit. These services and related components are designed to give the operator a viable option to conventional rig type workovers for many remedial wellbore operations.

Mission Statement Thru-Tubing Systems, Inc. will strengthen the company’s position as a value leader in the field by continuing to develop innovative systems and services that lead the industry in the field of thru-tubing and non-rig workover and completion technologies. TTS will offer its customers sound advice along with innovative and cost efficient quality services and equipment. This will be done to allow its customers the ability to successfully take advantage of and achieve the cost savings these technologies offer.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

3

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

TTS Field Services When it comes to thru-tubing products and services, TTS personnel have both a reputation for and a history of excellence in downhole tool design, technology application, on-site execution, and customer service. Years of experience in wireline, electric line, coiled tubing, cementing, and stimulation are represented among TTS personnel. TTS is the company that you can trust to find the best solutions to your problems. Put TTS expertise to work solving the problems faced in the life of your well. Specialty Services offered by TTS: Spiral Thru-Tubing Bridge Plug Installation Non-explosive Service Tool Operations (setting tools and dump bailers) Setting of Retrievable and Permanent Bridge Plugs/Packers/Cement Retainers Positive Displacement Bailer System (PDB) High Expansion Packer/Cement Retainer Installation X-Span Tubing/Casing Patch Installation Retrievable Packer Applications Packer Straddle Patch Cement Retainer Shut-in Valve Installation Gas Lift Jet Pump Downhole Choke Gage Hanger Deployment of Wireline Tools using Coiled Tubing Plugs Packers Cement Retainers Dump Bailer

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

4

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Workover / Completion Systems . TTS Tubing Patch Straddle Pack Installation (Utilizing the TTS Retrievable Thru-Tubing Packer System)

Features/Benefits  Can be installed via coil tubing, electric line, slickline or a combination, allowing for operator flexibility and associated cost savings.  Requires only two trips to set or retrieve on slickline or wireline; one or two trips on coil tubing. Saves time and risk compared to conventional tubing stop and pack-off alternatives requiring several trips to install.  Use of two TTS Retrievable Seal Bore Packers and a Floating Seal Assembly easily accommodate production-tubing movements caused by downhole temperature changes due to well killing, stimulation, and producing operations. Utilizing mechanical compression or tension set packers, wireline pack-offs, as well as inflatables, has little tolerance to production tubing movement. Also large I.D. /O.D. ratio packer creates larger finished bores than competitive systems.  Live well operations can easily be tolerated. In some cases eliminates the need and expense of well killing operations.  Each packer can be tested along with all connections of coil tubing as they are run into the well. Allows for removal and replacement of any failed components prior to attempting to flow the well.  Superior sealing and anchoring system. Multi-durometer packing systems hold pressure from above or below. Bi-directional caged slip design anchors packer in both directions and can handle much higher tail pipe loads (long patches not a problem).

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

5

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Tubing Straddle Patch Set Lower Packer

Locate Seals

Upper Packer Set

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

6

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Product Information – Packers / Well Intervention Series 5011 Retrievable Dual Seal Bore Tubing Packer General The TTS Series 5011 Retrievable DSB Thru-Tubing Packer System is a dual seal bore packer deployable via coiled tubing, jointed pipe, or wireline. Retrieval is accomplished by straight pull to release. It utilizes a proven multi-durometer packing system located above bi-directional caged slips. The standard differential pressure rating is 5000 psi at 300º F. Customizations are available for special sizes, corrosive environments, higher temperature or pressure requirements. Available for tubing sizes 2-3/8” to 5-1/2”.  One-trip installation, One-trip retrieve Thru-Tubing Packer.  Straight pull to release, no downward manipulation required.  Modular Gage Rings allow for optimizing seal gap.  Large ID/OD ratio for larger flow area.  Dual Bore design allows for full unrestricted ID bore on Seal Bore accessories  Bi-Directional caged slips located below the packing system provides increased retrievability.  Multi durometer packing system increases sealing ability.  Release mechanism is not affected by hanging weight or differential pressures allowing reduction of the required release forces to aid wireline retrieving.  Once Packer is released, the tool is locked in the release position allowing the ability to work up and down once released and not re-engage slips.

Applications        

Straddle packs (tubing patch) Velocity string installations Thru-tubing gas lift system installations GP Screen, Gage, Choke or Shut-in Valve hang-offs Washdown gravel packs Thru-tubing perforating Thru-tubing cement retainer Retrievable Bridge Plug (with accessory equalizing valve/plug)

Specifications Series 5011 Retrievable Packer System Tubing Size (in) 2-3/8 2-7/8 2-7/8 3-1/2 3-1/2 4-1/2 4-1/2 5-1/2

Tubing (wt) 4.70 7.80 – 8.60 6.50 9.30 – 10.20 12.70 – 12.95 10.50 - 13.50 15.10 17.0 – 23.0

Length (in) 42.62 43.94 39.97 45.54 42.87 53.27 53.27 67.22

Gage Ring * (in) 1.810 2.166 2.290 2.725 2.531 3.750 3.650 4.531

ID Bore (in) 1.000 1.250 1.380 1.625 1.380 2.000 2.000 2.812

Max Slip Range 2.02 2.31 2.45 3.00 2.76 4.10 4.10 4.90

NOTE: Other sizes available upon request

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

7

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Series 5011 Retrievable Straddle Pack System (Utilizing the TTS Retrievable Thru-Tubing Packer System) Utilizing the TTS Series 5011 Retrievable DSB Thru-Tubing Packer, an isolation straddle packer system can be installed via wireline, coiled tubing, or jointed pipe. When pressure control is required and/or lubricator height limits running length, modular latching seal extensions can be run in segments to achieve a straddle over a longer interval. This system can be used to patch holes in tubing, isolate zones, provide gas lift or jet pump installation.

Features/Benefits        

Modular design allows adjustable and unlimited length Dual Seal Bore design provides full opening ID thru Latch Seal Positive Indicating Latch Seal Packers hold differential pressure from above and below Requires only two trips to set or retrieve on slickline or wireline; one or two trips on coil tubing. Saves time and risk compared to conventional tubing stop and pack-off alternatives requiring several trips to install. Use of two TTS Retrievable Seal Bore Packers and a Floating Seal Assembly easily accommodate production-tubing movements caused by downhole temperature changes due to well killing, stimulation, and producing operations. Each packer can be tested along with all connections of coil tubing as they are run into the well. Superior sealing and anchoring system. Multi-durometer packing system holds pressure from above or below.

Application    

Retrievable Tubing Patch Isolation Straddle Gas Lift Installation Jet Pump Installation

Specifications Series 5011 Retrievable Straddle Pack System Tubing Size (in) 2-3/8 2-7/8 2-7/8 3-1/2 3-1/2 4-1/2 4-1/2 5-1/2

Tubing (wt) 4.70 7.80 – 8.60 6.50 9.30 – 10.20 12.70 – 12.95 10.50 - 13.50 15.10 17.0 – 23.0

Packer OD (in) 1.800 2.110 2.225 2.700 2.500 3.650 3.650 4.470

Gage Ring * (in) 1.810 2.166 2.290 2.725 2.531 3.750 3.650 4.531

ID Bore (in) 1.000 1.250 1.380 1.625 1.380 2.000 2.000 2.812

Length (in) 42.62 43.94 39.97 45.54 42.87 53.27 53.27 67.22

NOTE: Other sizes available upon request.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

8

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Product Information – Packer Accessories Series 5011 Retrievable Packer Accessories The TTS Series 5011 Retrievable DSB Thru-Tubing Packer System offers numerous accessories to customize the Packer System for the specific application needs. 5011-xxx-011

Anchor Latch Seal Assembly, a collet latch seal assembly for connecting straddle extensions in long intervals. TTS uses a specially designed proprietary molded seals to maximize seal and withstand stabbing installation.

5011-xxx-013

Locator Seal Assembly, locator seal assembly with no latch.

5011-xxx-014

Pulling Tool (Spear Type), bull dog spear used to pull Retrievable Packer.

5011-xxx-015

Anchor Latch Seal Assembly with Blow-out Plug, a standard Anchor Latch which allows the straddle system to be run closed and opened at a later date.

5011-xxx-111

Equalizing Sleeve Subassembly, when added to the bottom of the Packer, this subassembly creates a Retrievable Bridge Plug.

5701 series

Bow Spring Centralizer (BSC), TTS manufactures both rotational and nonrotational BSC to run in conjunction with straddle extensions.

6700 series

Polished Bore Receptacle (PBR), TTS has their own profile PBR to allow full ID opening Seal Assemblies. These PBRs thread onto pipe extensions for lengthening straddle assemblies. Standard ‘G’ profiles are also available.

6600 series

Beveled Coupling, TTS chamfers all couplings to eliminate flat surfaces on straddle assemblies.

7000 series

Blank Pipe, TTS uses N-80 grade tubing (minimum) for all straddle extensions, also used as a debris section on bottom of packer run as bridge plug. (Available in pre-cut lengths and threaded)

(‘xxx’ in the part number is to specify the packer size)

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

9

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Product Information – Packer Setting Assemblies Series 5011 Retrievable Packer Setting Assemblies The TTS Series 5011 Retrievable DSB Thru-Tubing Packer System offers numerous setting options to customize deployment of the Packer System for the specific application needs. Multi-stage Power Charge Wireline Setting Tool, Standard multi-stage power charge setting tool patterned after the original “GO” style tools. All TTS tools are adaptable to similar style tools available from vendors such as Owen Oil Tools, HPI, etc. Packers are also adaptable to Baker style setting tools. Series 5003 Hydraulic Setting Tool, multi-stage hydraulic setting tool uses applied pressure to workstring to generate required force to set packer. Series 3300 Big Bore Hydraulic Setting Tool, specially designed multi-stage hydraulic setting tool providing full ID equal to the packer ID. This system is can be left in hole atop a lower packer (s) and produced through without a reduction in flow ID. This is used when it is desired to set multiple packers in a single trip. It is also used for additional flow area for subsequent pumping operations such as gravel packing, cementing, acidizing.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

10

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Product Information – Retrievable Bridge Plugs Series 5014 Retrievable Bridge Plug (RBP) The TTS Series 5014 Retrievable Bridge Plug System is deployable via coiled tubing, pipe, or wireline. Retrieval is accomplished by a straight pull to equalize and again to release. It utilizes a proven multidurometer packing system located above bi-directional caged slips. The standard differential pressure rating is 5000 psi at 300ºF. Customizations are available for special sizes, corrosive environments, and higher temperature and pressure requirements. Available for tubing sizes 2-3/8” to 4-1/2”.

Features/Benefits         

One-trip installation, One-trip retrieve Bridge Plug. Straight pull to equalize and release, no downward manipulation required. Modular Gage Rings allow for optimizing seal gap. Pressure Equalizing Valve opens before release occurs. Bi-Directional caged slip design located below the packing system provides increased retrievability. Multi durometer packing system increases sealing ability. Standard external fishing neck for reliable latching. Release mechanism is not affected by differential pressures allowing reduction of the required release forces to aid wireline retrieving. Once RBP is released, the tool is locked in the release position allowing the ability to work up and down once released and not re-engage slips.

Applications       

Temporary abandonment Zonal Isolation Wellhead change out Storm Choke Deployment Plug Depth Locator for subsequent operations Selective testing/production

Series 5011 Retrievable Bridge Plug System Tubing Size (in) 2-3/8 2-7/8 2-7/8 3-1/2 3-1/2 4-1/2 4-1/2 5-1/2

Tubing (wt) 4.70 7.80 – 8.60 6.50 9.30 – 10.20 12.70 – 12.95 10.50 - 13.50 15.10 17.0 – 23.0

Packer OD (in) 1.800 2.110 2.225 2.700 2.500 3.650 3.650 4.470

Gage Ring * (in) 1.810 2.166 2.290 2.725 2.531 3.750 3.650 4.531

ID Bore (in) 1.000 1.250 1.380 1.625 1.380 2.000 2.000 2.812

Max Slip Range 2.02 2.31 2.45 3.00 2.76 4.10 4.10 4.90

NOTE: Other sizes available upon request

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

11

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Product Information Series 4800 Controlled Set High Expansion Packer Also known as the “Patch thru a Patch”, the High Expansion Packer was designed to travel through an existing casing or tubing patch or other ID restriction(s) and set in a larger ID tubular below. This system incorporates a variation of TTS’ “fixed slip” system design to ensure each slip segment is separated, properly aligned with the packer axis, and evenly spaced around the packer body. Further design features of the slips and packer body allow for increased extension of the slip into larger diameters than previously possible. Thru Tubing Systems is further pleased to introduce the Controlled Set System, another improvement to the Packer/Plug product line. The concept of this new feature is to have a control mechanism for sequentially setting each of the packer components. This ensures the elastomer is sufficiently energized prior to setting the lower slips. Precise, repeatable energizing of the packing element enables TTS to achieve a hydraulic seal from both directions. The High Expansion Packer can be coupled with TTS’ Anchor Latch Seal Assembly and Polished Bore Receptacle to create a variable length straddle system capable of isolating intervals below restrictions and still provide relatively large flow area for zones below. This system can be installed via coiled tubing, electric line, or wireline.

Specifications Series 4800 Controlled Set High Expansion Cement Retainer Part Number

OD (in)

4800-181-A-001

1.81”

.75”

Setting Range (in) Min Max 2.176” 2.441”

4800-219-A-001

2.19”

1.06”

2.630”

ID (in)

3.000”

*US Patent 7,578,353 B2

\

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

12

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Product Information Series 4800 - Controlled Set High Expansion Cement Retainer The High Expansion Cement Retainer was designed to travel through an existing casing or tubing patch or other ID restriction(s) and set in a larger ID tubular below while maintaining a sufficient thru-bore for pumping. This system incorporates a variation of TTS’ “fixed slip” system design to ensure each slip segment is separated, properly aligned with the packer axis, and evenly spaced around the packer body. Further design features of the slips and packer body allow for increased extension of the slip into larger diameters than previously possible. This system can be installed via coiled tubing, electric line, or wireline. Multiple options are available for the cement valve; a sliding sleeve valve can used to run in one trip on coil, a flapper valve can be used for a two trip system on wireline.

Specifications Series 4800 Controlled Set High Expansion Cement Retainer Part Number

OD (in)

4800-181-A-001

1.81”

.75”

Setting Range (in) Min Max 2.176” 2.441”

4800-219-A-001

2.19”

1.06”

2.630”

ID (in)

Pressure Rated (psi) 3000

3.000”

3000 *US Patent 7,578,353 B2

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

13

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products ACE Mix Cement Kits ACE MixTM High Shear Bond Cement Kits are designed to maximize bonding and sealing ability under harsh down-hole conditions. They provide sufficient fluid time to “round-trip” a bailer, while maintaining reasonable initial set times and excellent API fluid loss properties as well. The standard ACE Mix™ kit is packaged in two pails (dry blend and mix water) to yield 6 gallons of 16.4 ppg cement slurry for BHT 100oF – 300oF (a single pail kit without water is available for export or remote locations). The dry blend portion of the kit is divided and packaged into two separate 3 gallon bags inside the dry blend pail. This allows the kit to be mixed and used as two - 3 gallon batches, if preferred. The dry blend portion of the kit can be ordered packaged in a single 3 gallon pail to cut in half the weight to be lifted for safer handling operations. The ACE MixTM product line is organized around a single base cement kit that provides a high density, high shear bond, expanding cement slurry. This expanding, High Shear Bond formula is now available as the “standard” kit, not special order. The performance of ACE Mix TM exceeds performance of other standard kits available in head to head tests (see chart below). Relative Shear Bond and Anchor Strength

Relative Strength Percent

400 350 300 250 200

200 Deg F

150

280 Deg F

100 50 0 Kit I

Kit 2

ACE Mix

PRODUCTS TESTED

The base ACE MixTM kit is also designed to allow for the addition of specific application add-ins or “wild cards”. These add-ins specially enhance the performance of the kit for the unique condition. In this manner, the base cement kit adapts to the unique application requirement eliminating the need for numerous specialty kits. Simply select the proper Wild Card for the application and add to the base kit. For example, if the application is for 350oF, add the HTE wild card for Hi-Temp applications. There is no need to carry multiple kit versions and increase the amount of inventory. Wild Card add-ins are available for a wide variety of applications, with more under development as additional customer needs and requirements are encountered.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

14

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products

Description of Wild Card Add-ins Available For Use With ACE Mix Kits: 

HTE – High Temp Extender o Additives for extending operating temperature range from 300o F to 400o F.



LTX – Low Temperature Expansion o Standard expansion agents require minimal temperature of 200 o F to cause expansion of cement during cure cycle. This patented additive causes ACE Mix to expand at low temperatures from 100o F to 200o F increasing Shear Bond.



SSW – Saturated Salt Water o Certain brine and bromide fluids can cause problems for proper cement bailing, curing, and/or strength development. This additive prevents flash set in the bailer and regulates cure time in a high salinity environment. Slurry density is increased to 17.2 ppg using this additive.



HD-18 - High Density 18 ppg o Increases the slurry density to 18 ppg for use in heavy well fluids.

Kits are manufactured using strict acceptance criteria for all material components. Each criterion is verified by laboratory testing and documented. Additionally, each batch of cement kits is manufactured according to specific quality control procedures for the manufacturing process. Again, laboratory testing of each batch of kits is performed and documented. Samples of each kit batch are maintained at the lab for an extended time period for future verification. Information is kept by Lot number to provide component traceability of individual chemical components used in the manufacture of the kits. Kit performance numbers (fluid time, initial set, 12 hr and 24 hr compressive strength and API fluid loss) are included with each kit.

Additional Special Application Kits Available    

ETT – Extended Trip Time o Provides extra rig-up and/or run time by delaying initial set of cement. LCM – Lost Circulation Material o Bridging Material is added to the kit to assist bridging in slotted liners, etc. LTC – Low Temp Cure o Enables curing of slurry at BHT of 60o-100oF. XHT – Extreme High Temp o Extends operating range to BHT of 425oF

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

15

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products ACE Mix Cement (6 gallon) Kit Mixing Procedure Kit design:

One pail containing Premium Class “H” Cement with proprietary blend of additives separated into two bags each yielding 3 gallons of slurry packaged in a seven gallon pail. Also included in kit are Defoamer, Retarder, ½ gallon pail, and a 60 cc (ml) syringe. Domestic kits have a second pail containing required amount of water.

Slurry Density: Kit Yield: Water Requirement:

16.4 lb/gal 6 US gallons 3.0 US gallons (11.4 liters) Fresh Water

1. Measure BHT accurately prior to running cement. 2. For best results, the temperature of the dry blend and water solution needs to be 70 oF or above prior to mixing. Storage indoors recommended. 3. For best results, use high speed mixer with rpm > 550 (under load) to sufficiently shear cement while blending. 4. The kit may be mixed in a 3 gallon or a 6 gallon batch, follow guidelines related to desired batch size. 5. The ACE Cement Kit is designed to allow addition of specialty add-in components (known as “Wild Cards”, see Table 3) to accommodate unique well conditions without having to purchase a separate special kit. Wild Cards come in packet form with their own mixing instructions stating proper mixing order and any required change in water or retarder concentration. If using a Wild Card, read and follow the instructions provided with the Wild Card product to insure proper mixing order and procedure.

Mixing Procedure: Step 1:

Open the cement pail and remove the containers of defoamer, retarder, ½ gallon pail, and 60cc (ml) syringe.

Step 2:

Add the required amount of water to a clean mixing pail (6 gallon or larger). If mixing a full six gallon batch, use the entire contents of the water pail provided (domestic kit only). If desired, 3 gallon batches may be mixed. To mix in 3 gallon volume increments, scoop out three ½ gallon pails of the mix water and place into the mixing pail. NOTE: Export kits will require 3.0 US gallons (11.4 liters) of water for a 6 gallon batch or 1.4 US gallons (5.7 liters for a 3 gallon batch).

Step 3:

Shake the container labeled “defoamer” and pour the entire contents (for 6 gallon batch) or one-half of the contents (for 3 gallon batch) into the water pail. Mix for two minutes until blended well.

Step 4:

Determine the amount of retarder necessary from table 1, shown below. Add only the retarder amounts listed for that temperature range and batch size. Shake the bottle of retarder, and then add the total amount of liquid retarder listed for the temperature application to the water using the 60 cc (ml) syringe.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

16

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Table 1: Retarder Amounts vs. Temperature BHT (F) 100-149 150-190 191-200 201-210 211-220 221-230 231-240 241-250 251-260 261-270 271-280 281-290 291-300

Required Retarder Amount (3) Gallon Batch (6) Gallon Batch None None 11 cc (ml) 22 cc (ml) 27 cc (ml) 54 cc (ml) 44 cc (ml) 87 cc (ml) 60 cc (ml) 119 cc (ml) 76 cc (ml) 152 cc (ml) 103 cc (ml) 206 cc (ml) 136 cc (ml) 271 cc (ml) 179 cc (ml) 358 cc (ml) 206 cc (ml) 412 cc (ml) 239 cc (ml) 477 cc (ml) 255 cc (ml) 510 cc (ml) 271 cc (ml) 542 cc (ml)

Step 5:

Mix until the retarder is completely dissolved, but a minimum of five minutes. This is now your mix water to be used to make the desired amount of 16.4 lb/gal slurry.

Step 6:

If mixing total contents of kit, add both dry blend bags (sequentially) to the mix water containing retarder while high speed stirring. To mix a 3 gallon batch, add only one bag of the dry cement blend to the mix water containing retarder, while it is being stirred. Take care in adding the cement blend slowly (over a time period of approximately three minutes) into the mix water to allow for proper hydration of the cement and to prevent screening out of lumps of cement.

Step 7:

After completing Step 6, stir with high speed mixer (recommend to use pneumatic type) for 10-minutes.

Step 8:

Pour the cement slurry through a screen or grate to ensure that there are no large particles left un-mixed in the slurry. Verify density with a mud scale. Note: A non-pressurized mud balance may cause the slurry density to appear slightly (+/- .2 ppg) less than the actual density. If it is desirable to mix cement slurry to a lower or higher density, call TTS for Technical Support and information. Note: The slurry will be thicker than 16 # slurry.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

17

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Table 2: Fluid Time, Compressive Strength and Fluid Loss Data (Sample) Temp.(°F) 150 180 190 210 230 250 265 280 300

Time For 500 psi (hrs:min)

12 hour strength (psi)

24 hour strength (psi)

API Fluid Loss (mls)

6:52 6:41 5:37 8:35 7:13 9:48 7:47 6:03 6:28

1388 1476 2077 1935 2191 1125 1843 1628 3442

2550 2600 3100 3500 3600 3100 3000 4323 6055

62 60 60 58 56 58 60 58 60

Table 3: Wild Card Add-ins for ACE Mix Cement Kit (see product info for more detailed information) Designation

Name

HTE

High Temp Extender

LTX

Low Temp Expansion

SSW

Saturated Salt Water

HD-18

High Density

Application Increases BHT operating range from 300o F to 400o F Patented additive causes expansion of cement at BHT < 200o F during cure Allows cement to run and cure properly in high salinity well fluid Increases slurry density above 18 ppg

Table 4: Specialty Cement Kits available (see product info for more detailed information) Designation

Name

Application

ETT

Extended Trip Time

Increases slurry fluid time to allow for longer rigup and/or run times

LTC

Low Temperature Cure

Causes curing at BHT of 60o F to 100o F

LCM

Lost Circulation Material

Assists bridging in slotted liners, etc.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

18

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 9306 - Spiral Thru Tubing Bridge Plug TTS’ Spiral Thru-tubing Bridge Plug* is designed to run through a smaller pipe size or tubing restriction and set in larger ID casing below. The main application is for zonal isolation or abandonment as a base for a cement plug. Other possible uses include; depth control marker for subsequent gravel pack, whipstock, or perforating operations. Deployment of this patented plug system is possible using wireline or coiled tubing. The plug system consists of a heavy duty anchor and an expanding steel frame covered by a high expansion elastomer. The anchor holds the plug system in place as the steel frame is expanded and engages the elastomer against the ID of the casing wall. Plug construction (seal element and anchor) is modular to allow the operator to adapt to multiple running conditions. Total run-in length of the TTS Spiral Plug system (plug and setting tool) is a maximum of 14.5’ long. This is relatively short compared to currently marketed plug systems that may reach in excess of 30’ in length with their required setting tool. TTS has developed a special setting kit that allows deployment by commonly used power charge setting tools already used by service companies in their existing plug setting operations. Features/Benefits  Modular design increases operational efficiency  Short Overall Length increases ability to reach target zone  Compatible with all wireline systems increases setting options  Robust design

Specifications Series 9306 - Spiral Thru Tubing Plug Casing Size

Weight (ppf)

4-1/2” 5” 5-1/2” 6-5/8” 7” 7-5/8”

6.75-18.8 11.5 - 21. 9. – 26. 17.-28. 17.–38. 26.4 – 39

ID Setting Range (working)

Min 3.515” 4.154” 4.548” 5.666” 5.795” 6.500”

Max 4.216” 4.560” 5.192” 6.135” 6.538” 6.969”

Tubing Size

Plug OD

Plug Length (left in hole)

2-7/8” 2-7/8” 2-7/8” 2-7/8” 2-7/8” 2-7/8”

2.19” 2.19” 2.19” 2.19” 2.19” 2.19”

95.5” 95.5” 95.5” 95.5” 95.5” 95.5”

The Spiral Plug can be utilized in any tubular ID that falls within the listed range.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

19

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 7910 Electro-Hydraulic Bailer Bottom (EHBB) General The TTS Series 7910 Electro-hydraulic Bailer Bottom (EHBB) was designed to allow the use of a gravity dump bailer without requiring the use of explosives. The EHBB is a single operation valve designed to open a window at the bottom of a bailer string to allow the contents of the bailer to dump. The EHBB system is operational at BHP of 15,000 psi and BHT of 400oF.

Features/Benefits     

Non-Explosive – increased operational safety Non-Explosive - eliminates need for radio silence reducing down time Compatible with common bailer systems Adaptable to slickline operated system Sucker Rod bottom allows addition of Bow Spring, Impression Block, etc.

Specifications Series 7910 Electro-hydraulic Bailer Bottom (EHBB) Part Number

OD (in)

Length (in)

Thread

7910-169-A-002

1.69

36.57

1.63” TTS Gravity Bailer

7910-175-A-001

1.75

36.57

1.75” TTS PD Bailer

7910-200-A-002

2.00

36.57

2” TTS Gravity Bailer

7910-213-A-001

2.13

36.57

2.13” TTS PD Bailer

7910-300-A-002

3.00

36.95

3” Titan Gravity Bailer

7910-400-A-002

4.00

37.70

4” Titan Gravity Bailer

7910-500-A-002

5.00

38.88

5” Titan Gravity Bailer

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

20

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 1000 Positive Displacement Bailer The Thru Tubing Systems Positive Displacement Bailer System is utilized to ensure placement of cement at a precise depth. The TTS system is constructed of a series of internally flush bailer sections used to carry the cement into the well. A weight bar is released directing a swab piston through the bailer ID completely swabbing the contents at the working depth. The contents of the bailer are effectively isolated from the wellbore fluids during trip time. When used with a suitable designed cement (kit) system, the PDB reduces the possibility of cement stringing uphole as wireline is returned to the surface. Total bailer length can be adjusted by varying the number of bailer sections to achieve the desired tool length or cement volume. Optional actuators are available to make the system non-explosive, if desired. The bailer system is compatible with commonly used e-line equipment.

Specifications Series 1000 – Positive Displacement Bailer Part Number

OD (in)

Capacity (Gals/ft)

1000-150-A-001 1000-175-A-001 1000-213-A-001 1000-250-A-001 1000-300-A-001

1.50 1.75 2.13 2.50 3.00

.051 .076 .125 .183 .280

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

21

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 8299 – Flex Bailer Segment

General The TTS Flex Bailer Segment is designed to run between gravity bailer joints to reduce the length of stiff tool string. Its purpose is to facilitate getting below tight spots or corkscrewed tubing that prevent longer tool strings from passing through. This will allow the operator to run a full length bailer.

Features/Benefits  

Reduces stiff hook up length in gravity bailers, increases ability to deploy thru tight spots or bends in tubing. Allows full length bailer to be run reducing required number of runs to carry required volume to complete job.

Specifications TTS Flex Bailer Segment Bailer Size

Flex Joint O.D. (in)

Flex Joint I.D. (in)

Make-up Length (in)

1-3/8” 1-5/8” 2”, 2-1/8”, 2-3/8”

1.38 1.69 2.00

0.63 0.75 1.11

12.00 12.00 12.00

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

22

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 8300 - Gravity Bailer TTS Series 8300 Gravity Bailers are thin wall carbon steel tubulars used to convey cement, resin, sand, and/or other materials into the wellbore via wireline. Stainless steel material is available by special order. The standard bailer string version utilizes a blow-away aluminum bottom with blasting cap to open the lower end of the bailer string and “dump” the contents atop plugs, etc. Every TTS manufactured bailer section is pull tested to 5000# to verify structural integrity of the weld-on ends. This is one more way TTS’ quality inspection and control procedures help to insure trouble free operations in your well. The bailer system can become explosive-free using one of TTS’ Non-Explosive Bailer Actuators. Ask a TTS representative for details. Item

Description Bailer OD

1A 1B 2

Capacity/10’ Section Top Window Sub (GO) Top Window Sub (Schl) 10’ Bailer Section

Bailer size / Capacity / Part Number 1-3/8”

1-5/8”

2”

2-1/8”

2-3/8”

.67 gallons

.95 gallons

1.37 gallons

1.52 gallons

1.86 gallons

8300-138-030

8300-163-030

8300-200-030

8300-138-130

8300-163-130

8300-200-130

8300-138-011

8300-163-011

8300-138-031

8300-163-031

8300-200-011

8300-213-011

3

Blast Sub

4

Blasting Cap Wt.

Owen p/n DMP-3500-025 or Titan p/n 7110-000-039

5

Detonator

Owen p/n DET-3050-115 or Austin A-96L or equivalent

6 7

Aluminum Bailer Bottom Bottom Fill Sub (optional)

8300-238-011

8300-200-031

8300-138-033

8300-163-033

8300-200-033

8300-138-032

8300-163-032

8300-200-032

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

23

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products

Tubing Bailer Capacity 8

2-3/8” 7

2-1/8”

6

US Gallons

2” 5

4

1-5/8”

3

1-3/8” 2

1

0 10'

20'

30'

40'

Bailer Length in Feet

Bailer Size 10' 20' 30' 40'

1-3/8" 0.67 1.34 2.01 2.68

1-5/8" 0.95 1.9 2.85 3.8

2" 1.37 2.74 4.11 5.48

2-1/8" 1.52 3.04 4.56 6.08

2-3/8" 1.85 3.7 5.55 7.4

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

24

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products BAILER OD (IN) 13/8"

TUBING DATA OD

WEIGHT (#/FT)

(IN)

ID

DRIFT

CAPACITY

(IN)

(IN)

(GAL/FT)

11/2"

15/8"

2"

21/8"

23/8"

3"

BAILER VOLUME - US GALLONS PER TEN FOOT SECTION NIPPLE ID X

XN

R

21/16"

3.25

1.751

1.657

0.125

1.625

2-3/8"

4.70

1.995

1.901

0.162

1.875

2-3/8"

5.95

1.867

1.773

0.142

2-7/8"

6.50

2.441

2.347

0.243

2-7/8"

7.90

2.323

2.229

0.220

2.188

2-7/8"

8.70

2.259

2.165

0.208

2.125

3-1/2"

9.20

2.992

2.867

0.365

2.813

3-1/2"

10.20

2.922

2.797

0.348

2.750

3-1/2"

12.95

2.750

2.625

0.309

4"

9.50

3.548

3.423

4"

11.00

3.476

4-1/2"

12.75

4-1/2"

0.67 RN

0.72

0.95

1.37

1.52

1.85

3.10

PIPE FILL IN FEET/10' BAILER SECTION 5.36

5.76

7.59

-

-

-

-

4.13

4.43

5.85

-

-

-

-

4.71

5.06

6.68

-

-

-

-

2.76

2.96

3.91

5.64

6.25

-

-

2.010

3.04

3.27

4.31

6.22

6.90

-

-

1.937

3.22

3.46

4.56

6.58

7.30

-

-

2.666

1.83

1.97

2.60

3.75

4.16

5.07

-

2.635

1.92

2.07

2.73

3.93

4.36

5.31

-

2.17

2.33

3.08

4.44

4.93

6.00

-

0.514

1.30

1.40

1.85

2.67

2.96

3.60

6.04

3.351

0.493

1.36

1.46

1.93

2.78

3.08

3.75

6.29

3.958

3.833

0.639

1.05

1.13

1.49

2.14

2.38

2.89

4.85

13.50

3.920

3.795

0.627

3.688

3.456

1.07

1.15

1.52

2.19

2.42

2.95

4.94

4-1/2"

15.50

3.640

3.515

0.541

3.688

3.456

1.24

1.33

1.76

2.53

2.81

3.42

5.73

5"

13.00

4.494

4.369

0.824

0.81

0.87

1.15

1.66

1.84

2.25

3.76

5"

15.00

4.408

4.283

0.793

4.125

0.85

0.91

1.20

1.73

1.92

2.33

3.91

5"

18.00

4.276

4.151

0.746

4.000

0.90

0.97

1.27

1.84

2.04

2.48

4.16

5-1/2"

15.50

4.950

4.825

1.000

4.562

0.67

0.72

0.95

1.37

1.52

1.85

3.10

5-1/2"

17.00

4.892

4.767

0.976

4.562

0.69

0.74

0.97

1.40

1.56

1.89

3.17

5-1/2"

20.00

4.478

4.653

0.818

4.313

0.82

0.88

1.16

1.67

1.86

2.26

3.79

5-1/2"

23.00

4.670

4.545

0.890

4.313

0.75

0.81

1.07

1.54

1.71

2.08

3.48

1.791 1.710

2.313

2.205

2.562

3.813

1.560

2.329

3.725

4.313

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

25

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products BAILER OD (IN) 1-3/8"

CASING DATA

1-1/2"

1-5/8"

2"

2-1/8"

2-3/8"

3"

BAILER VOLUME PER TEN FOOT SECTION

OD

WEIGHT

ID

DRIFT

CAPACITY

0.67

0.72

0.95

1.37

1.52

1.85

3.10

(IN)

(#/FT)

(IN)

(IN)

(GAL/FT)

4-1/2"

9.50

4.090

3.965

0.683

0.98

1.05

1.39

2.01

2.23

2.71

4.54

4-1/2"

11.60

4.000

3.875

0.653

1.03

1.10

1.46

2.10

2.33

2.83

4.75

4-1/2"

13.50

3.920

3.795

0.627

1.07

1.15

1.52

2.19

2.42

2.95

4.94

4-1/2"

15.10

3.826

3.701

0.597

1.12

1.21

1.59

2.29

2.55

3.10

2.57

5"

11.50

4.560

4.435

0.848

0.79

0.85

1.12

1.61

1.79

2.18

3.65

5"

13.00

4.494

4.369

0.824

0.81

0.87

1.15

1.66

1.84

2.25

3.76

5"

15.00

4.408

4.283

0.793

0.85

0.91

1.20

1.73

1.92

2.33

3.91

5"

18.00

4.276

4.151

0.746

0.90

0.97

1.27

1.84

2.04

2.48

4.16

5"

21.00

4.154

4.029

0.704

0.95

1.02

1.35

1.95

2.16

2.63

4.40

5-1/2"

14.00

5.012

4.887

1.025

0.65

0.70

0.93

1.34

1.48

1.81

3.02

5-1/2"

15.00

4.974

4.849

1.009

0.66

0.71

0.94

1.36

1.51

1.83

3.07

5-1/2"

15.50

4.950

4.825

1.000

0.67

0.72

0.95

1.37

1.52

1.85

3.10

5-1/2"

17.00

4.892

4.767

0.976

0.69

0.74

0.97

1.40

1.56

1.89

3.17

5-1/2"

20.00

4.778

4.653

0.931

0.72

0.77

1.02

1.47

1.63

1.99

3.33

5-1/2"

23.00

4.670

4.545

0.890

0.75

0.81

1.07

1.54

1.71

2.08

3.48

6-5/8"

20

6.049

5.924

1.493

0.45

0.48

0.64

0.92

1.02

1.24

2.08

6-5/8"

24

5.921

5.796

1.430

0.47

0.50

0.66

0.96

1.06

1.29

2.17

6-5/8"

28

5.791

5.666

1.368

0.49

0.53

0.69

1.00

1.11

1.35

2.27

7"

17

6.538

6.413

1.744

0.38

0.41

0.54

0.79

0.87

1.06

1.78

7"

20

6.456

6.331

1.701

0.39

0.42

0.56

0.81

0.89

1.09

1.82

7"

23

6.366

6.241

1.653

0.41

0.44

0.57

0.83

0.92

1.12

1.87

7"

26

6.276

6.151

1.607

0.42

0.45

0.59

0.85

0.95

1.15

1.93

7"

29

6.184

6.059

1.560

0.43

0.46

0.61

0.88

0.97

1.19

6.72

7"

32

6.094

5.969

1.515

0.44

0.48

0.63

0.90

1.00

1.22

2.05

7"

35

6.004

5.879

1.471

0.46

0.49

0.65

0.93

1.03

1.26

2.11

7"

38

5.92

5.795

1.430

0.47

0.50

0.66

0.96

1.06

1.29

2.17

PIPE FILL IN FEET/10' BAILER SECTION

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

26

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products BAILER OD (IN) 1-3/8"

CASING DATA OD

1-1/2"

1-5/8"

2"

2-1/8"

2-3/8"

3"

BAILER VOLUME PER TEN FOOT SECTION

WEIGHT

ID

DRIFT

CAPACITY

(#/FT)

(IN)

(IN)

(GAL/FT)

75/8"

24

7.025

6.900

2.014

0.33

0.36

0.47

0.68

0.75

0.92

1.54

75/8"

26.4

6.969

6.844

1.982

0.34

0.36

0.48

0.69

0.77

0.93

1.56

75/8"

29.7

6.875

6.750

1.928

0.35

0.37

0.49

0.71

0.79

0.96

1.61

75/8"

33.7

6.765

6.640

1.867

0.36

0.39

0.51

0.73

0.81

0.99

1.66

75/8"

39

6.625

6.500

1.791

0.37

0.40

0.53

0.77

0.85

1.03

1.73

85/8"

28

8.017

7.892

2.622

0.26

0.27

0.36

0.52

0.58

0.71

1.18

85/8"

32

7.921

7.796

2.560

0.26

0.28

0.37

0.54

0.59

0.72

1.21

85/8"

36

7.825

7.700

2.498

0.27

0.29

0.38

0.55

0.61

0.74

1.24

85/8"

38

7.775

7.650

2.466

0.27

0.29

0.39

0.56

0.62

0.75

1.26

85/8"

40

7.725

7.600

2.435

0.28

0.30

0.39

0.56

0.62

0.76

1.27

95/8"

36

8.921

8.765

3.247

0.21

0.22

0.29

0.42

0.47

0.57

0.95

95/8"

40

8.835

8.679

3.185

0.21

0.23

0.30

0.43

0.48

0.58

0.97

95/8"

43.5

8.755

8.599

3.127

0.21

0.23

0.30

0.44

0.49

0.59

0.99

95/8"

47

8.681

8.525

3.075

0.22

0.23

0.31

0.45

0.49

0.60

1.01

95/8"

53.5

8.535

8.379

2.972

0.23

0.24

0.32

0.46

0.51

0.62

1.04

103/4"

32.75

10.192

10.036

4.238

0.16

0.17

0.22

0.32

0.36

0.44

0.73

103/4"

40.5

10.050

9.894

4.121

0.16

0.17

0.23

0.33

0.37

0.45

0.75

103/4"

45.5

9.950

9.794

4.039

0.17

0.18

0.24

0.34

0.38

0.46

0.77

103/4"

51

9.850

9.694

3.959

0.17

0.18

0.24

0.35

0.38

0.47

0.78

(IN)

0.67

0.72

0.95

1.37

1.52

1.85

3.10

PIPE FILL IN FEET/10' BAILER SECTION

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

27

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products 103/4"

55.5

9.760

9.604

3.887

0.17

0.19

0.24

0.35

0.39

0.48

0.80

113/4"

42

11.084

10.928

5.012

0.13

0.14

0.19

0.27

0.30

0.37

0.62

113/4"

47

11.000

10.844

4.937

0.14

0.15

0.19

0.28

0.31

0.37

0.63

113/4"

54

10.880

10.724

4.830

0.14

0.15

0.20

0.28

0.31

0.38

0.64

113/4"

60

10.772

10.616

4.734

0.14

0.15

0.20

0.29

0.32

0.39

0.65

133/8"

48

12.715

12.559

6.596

0.10

0.11

0.14

0.21

0.23

0.28

0.47

133/8"

54.4

12.615

12.459

6.493

0.10

0.11

0.15

0.21

0.23

0.28

0.48

133/8"

61

12.515

12.359

6.390

0.10

0.11

0.15

0.21

0.24

0.29

0.49

133/8"

68

12.415

12.259

6.289

0.11

0.11

0.15

0.22

0.24

0.29

0.49

133/8"

72

12.347

12.191

6.220

0.11

0.12

0.15

0.22

0.24

0.30

0.50

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

28

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 4010 - Wireline Pressure Setting Tool (Power Charge) The Pressure Setting Tool is used to provide the stroke and force required to set bridge plugs, packers, cement retainers, and other tension bolt/shear ring released devices via wireline. An electrically activated power large (gas generator) produces a sufficient volume of high pressure gas. This gas pressure, acting upon the piston area, provides the required amount of force to sever tension bolts or shear rings that commonly attach the downhole tools to the setting tool. In some models, the tool is made available in a multi-stage version. The addition of a stage increases the piston area to generate additional force using he same power charge, thus allowing higher tension bolt/shear ring values to be used if required. Tools are rated to 15,000 psi at 400° F.

Features/Benefits     

Self Bleeding - relieves gas charge by-products downhole increasing safety and eliminating manual bleeding of trapped pressure on surface Fluid Metered – reduces and controls speed of setting cycle Long Stroke – sufficient length to set tools requiring additional stoke Adaptable – fits most commonly available plugs Treated Surface – all exposed surfaces of a tool are specially treated for increased durability and decreased friction.

Specifications Series 4010 - Wireline Pressure Setting Tool Part Number

Description

Tool Length (in)

Max. Stroke (in)

Max. Shear Value (lbs)

4010-150-A-001 4010-169-A-001 4010-169-A-003 4010-213-A-001 4010-213-A-003

1-1/2” Single Stage 1-11/16” Single Stage 1-11/16” Multi Stage 2-1/8” Single Stage 2-1/8” Multi Stage

52.56 78.19 95.06 73.70 91.06

6.00 10.31 10.31 10.13 10.13

13,000 13,000 26,000 15,000 30,000

Power Charge Selection 1-1/2” Tools 1-11/16” Tools 2-1/8” Tools

1-1/2” Hi-Temp (425oF) 1-1/2” Low Temp (250oF) 1-11/16” Hi-Temp (425oF) 1-11/16” Low Temp (250oF) 2-1/8” Hi-Temp (425oF) 2-1/8” Low Temp (250oF)

Owen p/n JEC-5302-041 Owen p/n JEC-5302-054 Owen p/n JEC-5332-024 Owen p/n JEC-5332-124 JEC 5334-104 JEC 5334-103

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

29

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 4020 - Hydrostatic Setting Tool (Non-Explosive) The TTS Series 4020 Hydrostatic Setting Tool is a non-explosive setting tool used to provide the stroke and force required to set bridge plugs, packers, cement retainers, and other tension bolt/shear ring released tools. The tool utilizes a non-explosive actuator to allow bottomhole pressure (BHP) to enter the tool. The BHP acting upon the internal piston area generates the required amount of force to sever tension bolts or shear rings that commonly attach the plug/packer to the setting tool, all without the use of explosives. The Hydrostatic Setting Tool eliminates the dangers associated with handling explosives and the lost time and inconvenience of the imposed radio silence required when explosives are utilized. Additionally, the logistics of acquiring, permitting, and shipping explosives is eliminated, making operations in remote areas easier. Tools are designed as modular multi-stage version. Depending on BHP and the shear value requirement, an additional stage(s) may be required. The addition of a stage increases the piston area to generate additional force from the BHP, thus allowing higher tension bolt/shear ring values to be used or a lower BHP requirement. The lower end of the setting tool emulates the explosive version allowing the same setting sleeves to be used for both models.

Features/Benefits      

Non Explosive – easily, legally transported anywhere in the world. Self-contained – tool carries its own clean fluid Modular – allows variable number of stages to optimize BHP to force required Fluid Metered – reduces speed of setting cycle Long Stroke – sufficient length to set tools requiring additional stroke Adaptable – fit most commonly available plugs

Non-Explosive Actuator Options  

Electro-Hydraulic - 7900-169-A-001 DC Motor – 4400-169-A-001

Specifications Series 4020 – Hydrostatic Setting Tool Part Number 4020-169-A-001 4020-213-A-001

Description 1-11/16” Hydrostatic Setting Tool 2-1/8” Hydrostatic Setting Tool

Tool OD (in)

Max. Stroke (in)

Area / stage (in2)

Max. BHP (psi)

Max. Shear Value (lbs)

1.69

10.38

1.11

15,000

26,000

2.13

10.13

1.80

15,000

35,000

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

30

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 4200 - Fixed Slip Magna-Range Plug (Pressure Rated) Magna-Range Bridge Plugs are designed to travel through tubing ID restriction(s) and set in a larger ID tubular below. Traditional magna-range plugs have one piece cast iron slips that fracture into segments during the setting cycle creating potential problems in setting the plug properly. Segments can be broken off while running, fail to segment as designed, and segments may become misaligned, thereby improperly anchoring the plug body. Any problems are only magnified as the annulus between plug body and larger ID bore increases. TTS introduces the Fixed Slip Magna-Range Bridge Plug, representing an improvement over the traditional Magna-Range Bridge Plug product line. The purpose of the new system is to have a mechanism for ensuring proper deployment of the slips and guarantee accurate compression of the seal elements. It entails a unique method of attaching each slip segment to the plug body thereby holding the slips in proper axial alignment during setting. It also reduces frictional forces created by conventional slip design that must drag the lower slips upward in the tubing during setting. The Fixed Slip Magna-Range lower slip is not completely opened and set until the elastomer is sufficiently compressed. Proper placement and anchoring of the slips helps ensure proper retention of the elastomer seal elements in the proper position to establish and maintain a pressure tight seal. Testing has proven the Fixed Slip Magna-Range is effective in holding pressure from both directions and capable of withstanding reverse pressure cycles. TTS is the only manufacturer to post a pressure rating on a “Magna Range” plug.

Specifications Series 4200 Fixed Slip Magna Range Plug Part Number

OD (in)

4200-148-AC-001 4200-175-AC-001 4200-191-AC-001 4200-219-AC-001 4200-228-AC-001 4200-250-AC-001 4200-275-AC-001

1.480 1.750 1.906 2.187 2.281 2.500 2.750

Setting Range (in) Min Max 1.610 1.995 1.905 2.441 2.156 2.765 2.375 3.000 2.441 3.343 2.875 3.500 3.187 4.030

Tension Stud (lbs)

Δ Pressure Rating (psi)

8,000 13,000 13,000 13,000 13,000 25,000 25,000

5000 @ 1.995 I.D. 5000 @ 2.441 I.D. 5000 @ 2.441 I.D. 5000 @ 2.992 I.D. Pending / Pressure Test in progress Pending / Pressure Test in progress

3000 @ 3.920 I.D.

* Patent # 7,578,353 / Patent # 7,743,836

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

31

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 2105 - TTS Tubing Bridge Plug (10K) General The TTS Tubing Bridge Plug is designed with a few defining features that differentiate it from the conventional cast iron plugs currently on the market. It utilizes a specially designed Ecner Array elastomer system to provide structural integrity within the sealing element to withstand the differential pressure. This eliminates the fragile slotted metal backups normally employed to support the sealing element in the annular area between the plug and the pipe wall, making for a more robust plug design. The running diameter is smaller than most conventional plugs. Compact and dependable, the TTS Tubing Bridge Plug is easily set via wireline or pipe. Setting force is maintained by a ratcheting lock ring on top of the Bridge Plug.

Features/Benefits  Small run –in OD, increases ability to deploy thru and decreases possibility of sticking in tight spots or bends in tubing.  No fragile exposed metal backups reduces chance of plug damage which could lead to sticking the plug/setting tool system during deployment.  Heat treated slips designed to hold in 13Cr tubulars.  Lab testing verified ability to withstand pressure differential of 10,000 psi from both directions while subjecting plug to pressure reversal cycles.  Available with bottom adapter Bow Spring Centralizer or other wireline tool.

Specifications TTS Tubing Bridge Plug ID Setting Range (in) Min Max

Part Number

Tubing Size

Weight (ppf)

Plug O.D. (in)

2105-171-AC-001

2-3/8”

4.00 - 5.95

1.71

1.759

2.107

2105-209-AC-001

2-7/8”

6.40 - 9.50

2.09

2.125

2.563

2105-250-AC-001

3-1/2”

9.30 - 12.95

2.50

2.530

2.810

2105-263-AC-001

3-1/2”

5.75 - 10.30

2.63

2.670

3.258

Pressure Rating (psi) 10,000psi @ 1.995” I.D. 10,000psi @ 2.441” I.D. 10,000psi @ 2.750” I.D. 10,000psi @ 2.992” I.D.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

32

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 4250 - Cast Iron Bridge Plug General Compact, and dependable, the Cast Iron Plug is easily set via wireline or pipe. Setting force is maintained by a Ratcheting Lock Ring on top of the plug. Drilling out is easier due to the cast material. Sufficient sand or cement must be dumped atop the plug to prevent damage from perforating shock.

Features/Benefits   

Rated for 300 F (Nitrile). Available for Tubing and casing sizes from 4” to 20”. Pressure Rating dependent on OD.

Specifications Cast Iron Bridge Plug Pipe Size

Weight (ppf)

Plug O.D. (in)

4” 4-1/2” 4-1/2” 5” 5-1/2” 5-3/4” 6-5/8” 6-5/8” 6-5/8” 7” 7” 7-5/8” 8-5/8” 9-5/8” 10-3/4” 11-3/4” 13-3/8” 16” 18-5/8” 20”

5.6 - 14.0 9.5 – 16.60 9.5 – 13.5 11.5 – 21.0 13.0 - 25.0 22.5 - 25.2 34.0 17.0 - 34.0 17.0 – 22.0 23.0 – 40.0 17.0 – 35.0 20.0 - 39.0 24.0 - 49.0 29.3 - 53.5 32.7 – 51.0 38.0 - 65.0 48.0 – 72.0 65.0 – 128.0 76.0 – 96.5 94.0 – 133.0

3.120 3.500 3.710 3.710 4.240 4.240 4.750 5.340 5.610 5.340 5.610 6.090 6.960 7.710 9.500 9.500 12.000 14.125 17.250 18.375

ID Setting Range (in) Min 3.340 3.826 3.920 3.920 4.580 4.580 5.140 5.595 5.989 5.595 5.989 6.625 7.511 8.435 9.850 9.850 12.347 14.438 17.655 18.730

Max 3.732 4.090 4.560 4.560 5.047 5.047 5.595 6.366 6.655 6.366 6.655 7.263 8.248 9.063 11.150 11.150 12.715 15.250 18.730 19.124

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

33

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 4260 - Cast Iron Cement Retainer Compact, and dependable, the Cast Cement Retainer is easily set via wireline or pipe. Setting force is maintained by a Ratcheting Lock Ring on top of the cement retainer. On tubing models (< 4-1/2”), the cement valve is a molded poppet seal. Poppet Seals hold from below after the pumping pressure is reduced. On casing models (≥ 4-1/2”), the cement valve uses a balanced sliding sleeve. The balanced sleeve seals from both directions.

Features/Benefits  Rotationally locked for easy drillout.  Balanced Seal Valve provides protection against re-opening.

Specifications Cast Iron Cement Retainer Pipe Size

Weight (ppf)

Plug O.D. (in)

Valve Type

2-3/8” 2-7/8” 3-1/2” 4" 4-1/2” 5” 5-1/2” 6-5/8” 7” 7” 7-5/8” 8-5/8” 9-5/8” 10-3/4” 11-3/4” 13-3/8” 16” 18-5/8” 20”

4.0 - 5.8 6.4 - 6.5 5.75 - 10.3 5.6 – 14.0 9.5 - 15.1 11.5 – 18.0 13.0 - 23.0 17.0 – 34.0 32.0 - 38.0 17.0 – 35.0 20.0 - 39.0 24.0 - 49.0 29.3 – 58.4 32.7 - 60.7 60.0 – 70.0 48.0 – 72.0 65.0 – 128 76.0 – 96.5 94.0 - 133

1.750 2.220 2.750 3.120 3.593 3.937 4.312 5.375 5.375 5.687 6.312 7.125 8.125 9.437 9.937 12.000 14.125 17.250 18.375

Poppet Poppet Poppet Poppet Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve Sleeve

ID Setting Range (in) Min

Max

1.780 2.340 2.867 3.340 3.826 4.276 4.580 5.595 5.595 6.004 6.625 7.511 8.435 9.660 10.192 12.175 14.438 17.655 18.730

2.074 2.525 3.258 3.732 4.090 4.560 5.044 6.135 6.135 6.538 7.125 8.097 9.063 10.192 10.772 12.715 15.250 18.730 19.124

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

34

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 7850 - ACE Thru Tubing Umbrella Plug TTS introduces the Positively Deployed ACE Thru Tubing Umbrella Plug designed to pass through small restrictions and set in a larger ID tubular below. The ACE Thru Tubing Umbrella Plug firmly anchors into place a “metal petal” umbrella that functions as a cement basket to be utilized as a base for subsequent placement (dumping) of bridging material, cement, or resin. The unique setting mechanism positively deploys the bottom slips 12” below the end of the running sleeve. The TTS ACE Thru Tubing Umbrella Plug offers multiple features that improve reliability. Slip segments have been designed to hold 1600# each to improve setting and holding ability. A tool barrier is installed above the basket to prevent accidental damage due to wireline tool string contact. A second inverted basket directs any migrating fluids into the thru vent system.

Features/Benefits    

      

Positive Deployment of the ACE Thru Tubing Umbrella Plug from running sleeve to wellbore. The plug is mechanically pushed out of the running sleeve to overcome frictional forces caused by metal petals, BSC, and well fluid. Wireline Tool Barrier prevents accidental damage to basket during operations. Double basket supports cement column and diverts migrating fluid to vent. The ACE Thru Tubing Umbrella Plug uses overlapping spring steel petals to form a cone opening to the casing ID and provide a strong base to start the plugback operation. Metal petals are stronger than other cloth and Kevlar baskets and also provide resistance to damage by corrosive wellbore fluids. Case Hardened Slips assure placement in casing grades up to Q-125. Slip segments are set for specific setting range and will not set in outside sjpecified range A pressure balanced sliding sleeve vent valve maintains equalization across plug until it is closed, which is easily accomplished using wireline. Plugs for casing up to 7-5/8” are made “with shot”, a tube that contains a small amount of bridging material which deploys into the basket when set. Each plug is manufactured to accept the addition of a TTS Bow Spring Centralizer to assist entry of the running assembly into liner tops. Stocked for all API casing sizes (4-1/2” thru 9-5/8”). Special tubing, casing, and openhole sizes or Corrosive service (H2S, CO2) models available on request. Standard tool running diameter is 1.63” for 7-5/8” and smaller casing; 2” for 8-5/8” and larger casing; standard length is 13’ for vented, 6’ 6” for non-vented (7’6” for 8-5/8” and larger) Plugs with custom features (e.g., length, slip range, etc.) available on order.

Tool Series

Description

7850 7804 7805

Vented, Dual Basket Straddle Non-vented

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

35

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products

Series 7850 Vented ACE Thru Tubing Plugs Part Number

Pipe Size (in)

WS – With Shot

Running Length (ft)

7850-163-450 7850-163-550 7850-163-663 7850-163-700 7850-163-763 7850-163-863 7850-163-963

4” / 4-1/2” 5” / 5-1/2” 6-5/8” 7” 7-5/8” 8-5/8” 9-5/8”

Y Y Y Y Y N N

13’ 13’ 13’ 13’ 13’ 13’ 13’

Running OD (in) 1.63” 1.63” 1.63” 1.63” 1.63” 2” 2”

7850-163-450 7850-163-550 7850-163-663 7850-163-700 7850-163-763 7850-163-863 7850-163-963

Series 7850 Non-Vented ACE Thru Tubing Plugs Part Number

Pipe Size (in)

WS – With Shot

Running Length (ft)

7850-163-450 7850-163-550 7850-163-663 7850-163-700 7850-163-763 7850-163-863 7850-163-963

4” / 4-1/2” 5” / 5-1/2” 6-5/8” 7” 7-5/8” 8-5/8” 9-5/8”

N N N N N N N

6’6” 6’6” 6’6” 6’6” 6’6” 7’6” 7’6”

Running OD (in) 1.63” 1.63” 1.63” 1.63” 1.63” 2” 2”

7850-163-450 7850-163-550 7850-163-663 7850-163-700 7850-163-763 7850-163-863 7850-163-963

These specifications are for standard service, standard dimension plugs available in stock or next day delivery. Customer specified features, lengths, etc. can be accommodated given manufacturing time. Export plugs are shipped in as an assembly in the setting sleeve ready to run; this is designated by an “EX” at the end of the part number.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

36

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Tech Unit - ACE Umbrella Plug Field Operating Procedures using Push Tool (7801-169-A-001) and Blasting Cap Actuator (7801-169-A-011): 1.0

Tools Required 1.1. small screwdriver or hex key wrench set (depends on type of set screw used) 1.2.

2.0

set of small pipe wrenches or chain vise grips

Assembly of Push Tool to ACE Umbrella Plug and Running Sleeve 2.1. Remove the ACE Umbrella Plug from the shipping tube. Verify the plug specifications listed on the Plug QC Sheet match the specifications required. 2.2.

Remove nylon nut and PVC protection tube from Vent Valve atop ACE Plug Running Sleeve.

2.3.

Slide the Lower Linking Sleeve of Push Tool all the way up on the Upper linking Sleeve exposing the fingers of the Collet. The bottom of the Linking Sleeve should be adjacent to the base cut of the Collet fingers; this verifies the proper placement of the piston inside the Push Tool.

2.4.

Slide the Collet over the end of the Vent Valve and over the profile atop the ACE Umbrella Plug (Figure 1). The fingers of the Collet should slide over the raised diameter of the profile and the leading edge shoulders inside the collet.

2.5.

Slide the Lower Linking Sleeve down to the ACE Umbrella Plug Setting Sleeve. Rotate the Lower Linking Sleeve to engage the thread in the Plug Setting Sleeve. Continue turning until Lower Linking Sleeve is completely installed into ACE Umbrella Plug Setting Sleeve.

2.6.

Secure ACE Umbrella Plug Setting Sleeve by installing a Set Screw into retaining groove of Lower Linking Sleeve (Figure 2).

FIGURE 1

FIGURE 2

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

37

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products 3.0

Attachment of ACE Plug and Push Tool String to Wireline for Installation of Detonator NOTE: These procedures are written and provided as a guideline to assembly. They are not intended to replace standard oil and /or wireline company operational practices or safety procedures. Where a difference exists with such practice or procedures, standard company procedures should be followed. 3.1.

Inspect all threads on setting sleeve and Double Box Window Sub (item 2). Verify make-up and compatibility with the Wireline Company electrical contact sub (item 1).

3.2.

Attach the wireline tool string (weight bars, CCL, electrical contact sub for fluid exposed connection) to the wireline cablehead.

3.3.

Make electrical checks required to verify proper working of the wireline tool string (CCL, electrical continuity, etc.)

3.4.

Install or activate safety mechanisms required for handling and attaching explosives (safety key, grounding switch, grounding clamps, warning signs, etc.).

3.5.

Using suitable downhole wire, establish an electrical connection to the conductor on the electrical contact sub. The wire should be long enough to extend thru the Double Box Window Sub. Insulate the electrical connection for operation in an exposed fluid environment, (e.g., rubber boot, electrical tape, etc.). Use nylon string or boot sleeve as necessary.

3.6.

Make up the Double Box Window Sub to the wireline tool string. Pull the end of the attached wire thru the side window of the sub.

3.7.

Remove the Detonator Retainer (item 5) from the interior of the Tension Bolt (DO NOT remove the large external nut adjacent to the thread of the Top Sub of the Tension Bolt Actuator Assembly). Place the wires and the appropriate fluid exposed detonator into the Detonator Retainer (from the threaded end) and install the Detonator (item 3) into the ID of the Tension Bolt until it bottoms out. Secure into place with the Detonator Retainer. An appropriate detonator would be an Austin Powder Oilstar A-96L or equivalent.

3.8.

Pull the wire leads from the Detonator thru the bottom end of the Double Box Window Sub and out of the side window. Thread the Top Sub of the Tension Bolt Actuator Assembly (item 4) into the Window Sub.

3.9.

Cut the Detonator leads to length and make an electrical connection from one lead to the wire connection established in step 3.5 above. This connection must be appropriately sealed for exposure to well fluid. Secure the other Detonator lead to the ground screw in the Double Box Window Crossover Sub. Place excess wire back into interior of the sub and secure.

3.10. The Blasting Cap Actuator is now armed and ready to run into the well.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

38

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products 4.0

Field Operating Procedure 4.1. Shut-in well 48 hours prior to starting plugback operations. KEEP THE WELL PRESSURE STATIC UNTIL YOU HAVE COMPLETED THE PLUG BACK PROJECT AND THE PLUG IS TESTED. 4.2.

Perform an initial inspection of the well when first arriving at the well site. Record wellhead pressure and time. Pressure up the lubricator to well head pressure prior to opening the swab valve. Equalization of lubricator pressure and wellhead pressure prior to opening valve is required before each run. If the well has a full column of liquid to the surface, it also requires bleed-off of pressure increase caused by displacement when going inhole and replacement of the fluid when coming out of the hole.

4.3.

Make a full length (same as dump bailer string) gage run, preferably with a thermometer or other temperature recording device. Record the BHT. Locate and note fluid level if possible. Note any tight spots. Run CCL across plug interval and determine if sufficient markers are present for accurate depth control via CCL.

4.4.

Verify dimensional data from ACE Umbrella Plug QC Sheet corresponds to well parameters (QC sheet attached to plug shipping tube). Note dimensions for slip placement, basket location, and bottom of the plug.

4.5.

Make up ACE Umbrella Plug running assembly with a CCL. An optional Bow Spring Centralizer is available to attach to the bottom of the plug for use in high angle wells and/or re-entry into smaller ID (e.g., isolation packer, liner top). 4.5.1.

NOTE: The ACE Umbrella running leave has a heavy wall segment approximately 2-1/2” long immediately below the threaded end. Place wrenches only on this area when making up tool string. Do not clamp on the thin wall tube below the heavy wall segment.

4.5.2.

Run the ACE Umbrella Plug in the hole. Once at desired depth, carefully tie in with casing collars. Locate the ACE Umbrella Plug below the setting depth and slowly pull up to the desired setting depth. If the setting depth is not critical, it is recommended that the bottom set of slips be set 1 foot into a perforated interval or 1 foot below a casing collar connection.

4.5.3.

NOTE: The bottom end of the ACE Umbrella Plug is positively deployed one foot out the end of the setting sleeve when set. This must be added to the setting depth to place the basket at the desired depth.

4.5.4.

Fire detonator to initiate Push Tool and release ACE Umbrella Plug at desired setting depth. Wait 1 minute and pull off bottom at 25º) wells, in cross flow environment, or when multiple open perforation zones exist. Locate the end of the bailer 2 feet above the vent valve to dump. If the hole angle is higher than 60º and annular spacing will allow passage of the bailer string, locate the bailer bottom 2-3 feet above the basket to dump bridging material. NOTE: Avoid contact with the basket. Contact to the metal petal basket can cause damage.

4.7.

Make dump bailer runs to place initial cement volume until it is within 12 – 18 inches below the vent ports prior to closing the vent valve (this is the base plug). Dump cement as close to top of previous run as possible. As with bridging material, if annular spacing allows, locate the end of the bailer 1-2 feet above the top of the previous run. Pull off bottom at < 30 fpm. Maintain this speed on all cement bailer runs within 1000 feet of plug.

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

39

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products 4.8.

Wait a minimum of 18 hours after the last dump bailer run before closing the vent valve (unless using Ultra Set Activator to eliminate waiting time, see product information on Ultra Set Activator for details).

4.9.

Make up tool string consisting of CCL, weight bars, centralizer (s), and Lead Impression Block (LIB) and run to top of plug. Set down atop vent valve to close vent, it is not necessary to beat down with excessive force.

4.10. Make additional bailer runs as required to achieve plug height. 4.11. Wait a minimum of 24 hours after the last dump bailer run before pressure testing the cement plug (unless using Ultra Set Activator to eliminate waiting time, see product information on Ultra Set Activator for details).

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

40

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 1201 – Selective Release Tool The Thru Tubing Systems Selective Release Tool is designed for use with wireline deployed explosive or propellant tools. It is installed as an integral component in the tool string between the CCL and the firing sub attached to the top of the tool body. The purpose of the tool is to guarantee separation of the expended or used downhole tool from the basic wireline BHA (cablehead, sinker bars, CCL) used to deploy the downhole tool. An operator may need to jettison a downhole tool for a variety of reasons, although it is primarily due to a change in tool OD or shape that would make retrieval to the surface risky. This would be the case with perforating guns, jet cutters, etc. The Selective Release Tool gives the operator the option of release at any time after the downhole tool is functioned by selectively discharging a second detonator. It utilizes pressure from the detonator and/or subsequent BHP flooding into the tool upon detonation. Special features incorporated into the design of the Selective Release Tool eliminate possible problems that have been encountered when utilizing other commercially available release tools. Some available tools require the lower half of the tool string to become stuck and the top side to be pulled using the wireline unit to cause the components to separate. One unique feature of the Selective Release Tool is the positive separation of the wireline BHA from the expended tool. This is accomplished by an internal shifting piston applying opposing force between the two halves and causing separation without assistance from the wireline unit. The Selective Release Tool works even when deployed in a horizontal section of a well. Another feature of the Selective Release Tool’s design is the distribution of weight and applied forces on the tool components. The weight of the downhole tool string is distributed to a series of steel balls or keys in an internal profile. This eliminates the possibility of an accidental release during primary tool actuation, by forces exerted on the severing tension bolt used to suspend the downhole tool on other commercially available tool releases. The Selective Release Tool is capable of carrying a total tool load of up to 10,000# and will operate at BHP of 15,000 psi. The BHT is only limited by the explosives and seals selected. The upper portion of the Selective Release Tool returned to the surface is easily re-dressed for re-use.

Series 1201 Selective Release Tool Part Number

1201-169-A-004

OD

1.69”

1201-169-A-006 (Top Fire) 1.69”

Max Tool String Weight

10,000#

10,000#

10,000#

1201-275-A-003 2.75”

Length (Overall)

32.25”

31.32”

31.11”

Length (Make-up)

30.87”

29.24”

31.11”

Length (Left in hole)

8.02”

6.39”

12.57”

Max BHP

15,000 psi

15,000 psi

15,000 psi

Connection (Top)

1-13/16” ‘GO’ Box

1-13/16” ‘GO’ Box

1-5/8”– 6 Acme Box

Connection (Bottom)

1-13/16” ‘GO’ Pin

‘GO’ Button (long)

1-5/8”– 6 Acme Box

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

41

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

Wireline Products Series 1200 – Auto Release Tool The Thru Tubing Systems Auto Release Tool is designed for use with wireline deployed explosive or propellant tools. It is installed as an integral component in the tool string between the CCL and the firing sub attached to the top of the tool body. The purpose of the tool is to guarantee separation of the expended or used downhole tool from the basic wireline BHA (cablehead, sinker bars, CCL) used to deploy the downhole tool. An operator may wish to jettison a downhole tool for a variety of reasons although it is primarily due to a possible change in tool OD or shape that would make retrieval to the surface risky. This would be the case with perforating guns, jet cutters, etc. The Auto Release Tool separates at the time of downhole tool function. It utilizes pressure from the tool activation and/or subsequent BHP flooding into the tool after activation. The tool operation is passive from the operator’s point of view, no subsequent firing of secondary detonators or additional surface operations must be performed for the expended tool to be released. Special features incorporated into the design of the Auto Release Tool eliminate possible problems that have been encountered when utilizing other commercially available release tools. Some available tools require the lower half of the tool string to be stuck and the top side to be pulled using the wireline unit to cause the components to separate. One unique feature of the Auto Release Tool is the positive separation of the Wireline BHA from the expended tool. This is accomplished by an internal shifting piston applying opposing force between the two halves and causes separation without assistance from the wireline unit. The Auto Release Tool was actually designed to function when deployed in a horizontal section of a well. Another feature of the Auto Release Tool’s design is the distribution of weight and applied forces on the tool components. The weight of the downhole tool string is distributed to a series of steel balls or of keys located in an internal profile. This eliminates the possibility of an accidental release during primary tool actuation, by the forces exerted on the severing tension bolt used to suspend the downhole tool on other commercially available tool releases. The Auto Release Tool is capable of carrying a total tool load of up to 10,000# and will operate at BHP of 15,000 psi. The BHT is only limited by the explosives and seals selected. The upper portion of the Auto Release Tool returned to the surface is easily redressed for re-use.

Series 1200 Auto Release Tool Model Number

1200-169-A-004

1200-169-A-006 (Top Fire)

OD

1.69”

1.69”

Max BHP

15,000 psi

15,000 psi

Max Tool String Weight

10,000#

10,000#

Length (Overall)

15.57”

18.50”

Length (Run-in)

14.19”

15.86”

Length (Left in hole)

4.71”

6.39”

Connection (Top)

1-3/16”-12

1-3/16”-12

Connection (Bottom)

1-3/16”-12

‘GO’ Button (long)

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

42

In some International areas TTS products are available through authorized service providers.

4102 Highway 90 West, New Iberia LA 70560 Phone: (337)-606-0031  Fax: (337)-606-0039  E-Mail: [email protected]

TTS Rental Equipment Thru-Tubing Systems (TTS) offers a variety of wireline tools, equipment, and accessory items for shortterm or long-term rental. Whether the need is ongoing as a part of a strategy for equipment sourcing or temporary for a special once-in-awhile type service or to cover tool unavailability due to transit logistics, TTS can help fill the void. Equipment rental from TTS provides the source for tools that are wellmaintained and inspected after each use. TTS also offers customer-assigned rental boxes whereby TTS handles the long-term maintenance and inspection services of tools designated for use only by that client under a long-term agreement. This insures familiarity of the field crews with the proper assembly and use of the equipment provided. This helps in reducing the opportunity for problems associated within incompatibility between suppliers.

Power Charge Setting Tools:       

1-1/2” Shorty 1-11/16” Single-Stage Long Stroke 1-11/16” Multi-Stage 2-1/8” Single-Stage Long Stroke 2-1/8” Multi-Stage E-4 #10 E-4 #20

Junk Baskets Gage Rings Gravity Dump Bailer Systems (1”, 1-3/8”, 1-5/8”, 2”, 2-1/8”, 2-3/8”, 3”, 3-1/2”, 4”,5”)     

Firing Head Top Fill Window Bailer Joint Bottom Fill Sub Blast Sub/Cap Chamber

Bailer Clamp Slurry Mixing System Bottom Fill System – with TTS’ Quick Connect Fill Valve Density Scale Bow Spring Centralizer Lead Impression Block

Thru-Tubing Systems, Inc. products and services are subject to standard terms and conditions. Unless noted otherwise, trademarks and service marks noted herein are the property of Thru-Tubing Systems, Inc. © 2013. Thru-Tubing Systems, Inc. All rights reserved.

43

In some International areas TTS products are available through authorized service providers.