Fastest & Easiest Removal Solutions Since 1990 Put Our Experience To Work For You
Cutters Pages 6-9
Removers Pages 10-18
Parts Page 9
Support 1-954-941-9744
Best Prices & Service
MADE IN USA
Guaranteed
Est. 1990
www.RemoveFaster.com
FS050™ FS200 Deluxe™
MV5™
X3™
FS350™ SPS10™ LNX8™
FS150™
MADE IN USA
© 2013 SMITH Manufacturing Co., Inc. All Rights Reserved.MADE IN USA Est. 1990
Est. 1990
VISIT US AT
RemoveFaster.com
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
SMITH Manufacturing
ARE YOU BUYING FROM SMITH?
MANUFACTURING
Cutters / Removers / Parts / Support
MANUFACTURING
(954) 941-9744
www.SMITHMFG .com
www.SMITHMFG .com
hat drives my passion to help you earn more, removing faster?
™
SMITH Mission: to help make our customer’s hard-work easier and faster. Core Values: Passionate, Inquisitive, Appreciative, Innovative Our Priorities: Innovation, Awareness, Partnerships, Processes, Talent
BEFORE
AFTER w/VACUUM
Contractors are always looking for better ways to prepare concrete and asphalt surfaces. At SMITH, our strong core values and priorities are set to build and deliver reliable performance removal products and services that help our customer finish their jobs on-time and under budget leaving longer-lasting surfaces.
As a former striping contractor, I have experienced firsthand the many job frustrations that arise when working with a supplier that just doesn’t care. Doesn’t care enough to ask the right questions. Doesn’t care if what they sold is correct or even delivered on time. Working with the wrong supplier can make a job that looks profitable on paper become a money-pit. Being on the side of the road in the summer of 1975 was a watershed moment. An equipment breakdown, due to a supplier failing to deliver the right parts, created a chain of events that resulted in loss of life. I will never forget that moment and it’s what drives my “get it right at all costs” passion today. Even naming the company SMITH gave me “no wiggle room” to let someone down. But that’s why I did it, and every day I challenge my employees to continuously improve and to look for solutions to end our customer’s frustrations and help them earn more, removing faster.
SMITH MANUFACTURING is your one-stop savings source for on-time delivery of reliable cutters, removers, parts and support to help hard-working contractors remove faster, safer and more cost-effectively on asphalt and concrete with better surface finishes. Since 1990, the SMITH brand is synonymous with quality and preferred by contractors, governments, manufacturers and distributors desiring the very best USA-made equipment, ultra-premium-life cutters and wear components at the most competitive prices.
Performance
It’s founder, Steven Smith, built a team of qualified, experienced and passionate employees with over a century of coatings and removal experience that are empowered to help customers solve their toughest surface preparation problems. Formerly from a SMITH Representative President of Pave-Mark Corp., Steven first introduced carbide SMITH First cutter solutions for stripe Make it Last removal, championed contractor job initiatives for surface prep, groove-inlay and no-groove erasing.
This brochure is only a summary of the products and services we offer. Our website SmithMfg.com offers more details with removal tips, downloads and more. Of course I encourage you to call us so we can put our experience to work for you.
™
“SMITH considers manufacturing a core competency and one of the primary ways we are able to give customers an advantage,” says Wade Barrineau, VP of Operations. “Our equipment is custom built in house so we can deliver quality products reliably in the quantities needed by our customers. We are most proud of our research and development of new products while continuously improving our established product line. Solving customer’s removal problems is a challenge I take pride in and with our experienced personnel, flexibility and capabilities, we can ramp up quickly to meet our customers’ demanding schedules.” As a quality responsible manufacturer, SMITH maintains the largest inventory of machines and consumable wear components. SMITH is your one-stop reliable parts source for those that own a variety of scarifiers, planers, grinders, line removers, routers, groovers, shavers, scabblers and other removal equipment looking for better performance and cost savings. SMITH components out-perform the originals. SMITH-First initiatives help create jobs and lasting surfaces. The SMITHing process is designed to make everyone’s job easier and create value for operators and end users. The “Removal Selection Guide” (page 4) helps users successfully prepare for their next removal project. Everything we do is to maximize the customer’s experience.
BUY DIRECT
“SMITH Manufacturing, how may I help you?”
MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Knowing removal is hard-work, SMITH will continue to help make it easier for their customers by innovating, educating, growing partnerships, improving processes and seeking talent to sustain and grow our industry.
Best removal, Steven Smith President 800-653-9311
[email protected] MADE IN USA Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
World-Class Service, Selection, Quality, Innovation Cutters / Removers / Parts / Support
(954) 941-9744
2
Visit us at www.SmithMfg.com
Est. 1990
What customers say about SMITH “I always recommend SMITH to anyone looking for an easy solution to remove striping fast. I am a fan of their “spot-on” customer service and always impressed with their wide selection of cutters. Every year, I find some new innovation that keeps us competitive.” M. Allen
JOIN TODAY! S M IT
How can SMITH help you RemoveFaster? It’s not only how SMITH answers the phone but a core value commitment to providing their customers with uncompromised service and support. If you are not a SMITH customer now, ask your peers why they trust SMITH as their one-stop savings source. You’ll soon discover the real savings and benefit from what the SMITH name stands for – Surface-Prep Method Insuring Total Happiness. You won’t just remove-it, you’ll SMITH-it MADE IN USA Est. 1990
H
REMOVAL
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
3
TM
Removal Selection Guide
Cutter Selection Guide
Scan Code For Online Removal Selection Guide
MANUFACTURING
MANUFACTURING
Cutters / Removers / Parts / Support
Cutters / Removers / Parts / Support
(954) 941-9744
(954) 941-9744
www.SMITHMFG .com
www.SMITHMFG .com
What material are you removing?
What surface are you working on?
❑ Asphalt ❑ Build-ups ❑ Coatings ❑ Cold-plastics ❑ Concrete ❑ Concrete forms
❑ Dirt, Oil or Grease ❑ Epoxy ❑ Flaking paint ❑ High-spots ❑ Mastics or Glues ❑ Mortar or Grouts
❑ Non-skids ❑ Overlays ❑ Preform tapes ❑ Polyurea ❑ Prep surfaces ❑ Raised sidewalks
❑ Sealer or Cures ❑ Surface-marks ❑ Thermoplastic ❑ Traffic paints ❑
❑ Balconies or Decks ❑ Brick or Pavers ❑ Commercial floors ❑ Dairy barns
❑ Dense-grade HMA ❑ Ice ❑ Open-grade HMA ❑ Roughen concrete
❑ Sidewalks/Walkways ❑ Slurry, chip, fog seals ❑ Smooth concrete ❑ Stamped surface
❑ Steel surfaces ❑ Tined concrete ❑ Uneven surfaces ❑ Wood floors
Age of surface?
❑ 0 – 30 days
❑ 1 – 12 months
❑ 1 – 4 years
❑
Surface condition?
❑ Smooth
❑ Tined
❑ Rough
❑
Ambient condition?
❑ Wet
❑ Dry
❑ Temperature
Will toppings be applied?
❑ No
❑ Yes
❑ Type
Your removal depth?
❑ -1/4" - 0"
❑ 0” - 1/8”
❑ 1/8” - 1/4”
Desired finished texture? CSP1 Acid Etched CSP2 Grinding CSP3 Light Shotblast CSP4 Light Scarification CSP5 Medium Shotblast CSP6 Medium Scarification CSP7 Heavy Shotblast CSP8 Scabbled CSP9 Heavy Scarification
❑ CSP1
❑ CSP2
❑ CSP6
❑ CSP3
❑ CSP7
o
❑ CSP8
❑ CSP5
❑ other
❑ CSP9
❑ Yes–Hepa
Walls or obstacles?
❑ No
❑ Yes
❑ Type
Your Power needs?
❑ Air
❑ Electric
❑ Gas
❑ Propane
When does your job start?
❑ 0–5 Days
❑ 6–29 Days
❑ 30–60 Days
❑
When will your job end?
❑ 0–5 Days
❑ 6–29 Days
❑ 30–60 Days
❑ ❑ ❑ Expert: 5+ yrs
Daily Production Needs?
❑ 0–99 SF
❑ 100–999 SF
❑ 1000–9,999 SF+
Your labor experience?
❑ None
❑ Novice: 0-1 yr
❑ Apprentice: 1-4 yr
Got equipment?
❑ No
❑ Yes
❑ Make/Model
Got cutters?
❑ No
❑ Yes
❑ Type/Qty.
Capital budget?
❑ 0 to $1,999
❑ $2,000 to $4,999
❑ $5,000 to $14,999
❑
Cutter budget?
❑ 0 to $1,999
❑ $2,000 to $4,999
❑ $5,000 to $14,999
❑
Working altitude?
❑ Below sea level ❑ 0 – 500 feet
❑ 501 – 2,000 feet ❑ 2,001 – 5,000 feet
❑ 5,001 – 15,000 feet ❑ 15,001 +
Est. 1990
Wire Brush
Cutter Drum Set-up
All Brushes
What customers say about SMITH “Before starting any surface preparation job, we use this guide to assure we have the right cutters, equipment and personnel to complete the job on-time and on-budget.” S. Hendren
Prep-It ™
M
C
X
Prep-it strips
Finish-It ™
Flail-It ™
Strip-It ™
Mill-It ™
Scrape-It ™
Plane-It ™
Steel Flails
Carbide Flails
4N1 / 300s Full-Width
Carbide Millers
* Carbide Scrapers
Carbide Picks
UNIVERSAL
All Preps
1/2 Load
Beam
Star
With With With All With All 1/2 All All All Cutters Spacer Cutters Spacer Cutters Spacer Cutters Spacer Cutters Load
Surface Finish
CSP1
Service Life
Short
Medium
Short
Long
Longest
Long
Long
Long
$$
$$
$
$$
$$$
$$
$$$
$$
Ease of Use Best For: A - Asphalt C - Concrete S - Steel
CSP3 CSP4 CSP4 CSP5
CSP6 CSP9 CSP3 CSP4 CSP4
CSP5 CSP4 CSP5
CSP8 CSP9
Easy
Moderate
Easy
Easy
Moderate
Moderate
Moderate
Moderate
Dirt, Oil, Grease, Flaking paint, Prep surfaces, Sealer, Cure
Dirt, Oil, Grease, Ice, Flaking paint, Prep surfaces, Sealer, Cure
Prep surfaces, Traffic paints, Coatings, Light profiling
Coating, Control depth, Grooving, Cleaning, Routing, Surface marks
Epoxy, Tapes, Plastics, Thermoplastics
A•C•S
A•C
A•C•S
For most applications incl. traffic paints, Coatings, Uneven joints/surfaces
A•C•S
A•C•S
A
Non-skids, Mastics, Glues, Tapes, Plastics, Thermoplastics, Joint compounds
Uneven joints and surfaces, High spots or raised sidewalks, Overlayments
A
A•C
Rotary Style Cutters
Drum Style Cutters
❑ Yes
4
C
Best Cutter Selection
Cost
❑ No
MADE IN USA
Cure-It ™
❑
❑ CSP4
F
Drum Style Cutters
o
F
Will dust need to be collected?
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
Desired Surface Finish Textures (CSP1-9) by selecting the right cutter drum, offset spacing pattern (F, M, C, X) and removal process we call SMITHing. Cutters can be set inline to groove and at narrower widths. Adding spacers increases cutting penetrations. (F) - 0 spacer; (M) - 1 spacer; (C) - 2 spacers; (X) - 3 spacers.
(cont.)
Grind-It ™
Cure-It ™
Erase-It ™
Erase-It ™
Erase-It ™
Grind-It ™
Plane-It ™
Best Cutter Selection
Diamond Shavers
Wire Brush Rotary Disc
Carbide Pin Rotary Bits
Carbide Pin Rotary Bits
Carbide Pin Rotary Bits
Diamond Turbo
Carbide Pick Rotary Disc
Cutter Drum Set-up
With All Blades Spacer
Surface Finish
CSP2 CSP2
UNIVERSAL
Cutter Style
1/2 All Plugs Cutters Load
Discs
6 Brushes
24 Pin
48 Pin
72 Pin
Surface Finish
CSP1
CSP6
CSP5
CSP4
CSP2
CSP4 CSP7
Short
Medium
Long
Long
Medium Long
Medium
$
$
$$
$$
$
$
Service-Life
Long
Service-Life
Cost
$$$
Cost
Ease of Use
Moderate
Ease of Use
Moderate
Easy
Easy
Easy
Moderate
Moderate
Best For: A - Asphalt C - Concrete S - Steel
Surface marks or build-ups, Uneven joints and surfaces, Groove, Grind
Best For: A - Asphalt C - Concrete S - Steel
Dirt, Oil, Grease, Flaking paint, Prep surfaces, Sealer, Cure
For most applications incl. thick cold plastics, thermoplastics, preform tapes, leveling
Thermoplastics, Tapes, Epoxy, Paints, Overlays, Prep-surfaces, Joints
Concrete surfaces with paints, nonskids, prep surfaces, best finishes
High spots, Uneven surfaces, concrete, Cure, Surface-marks, Polishing
Uneven joints and surfaces, High spots or raised sidewalks, Overlayments
C
A•C•S
A
A•C
SMITH drums are available for all machine makes and models. Contact your SMITH Representative for the best cutter selection for your equipment and job.
C
C
C
MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
5
Scan Code For Online Cutter Selection
Ultra-Premium-Life SMITH Cutters + Your Equipment = RemoveFASTER MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Grooving, Shaving, Polishing? Installing RPM’s? SMITH diamond segments are manufactured with 40% concentration ultra-premium, (950 and 975 GE grade) diamonds through a computer controlled process. Our unique matrix bonding system assures optimum performance and long life. Based on your cutting requirements, segments are laser welded or soldered, for costeffective wet or dry cutting of asphalt, concrete, brick, block and stone.
Snowplowable
Slot Cut
Specify your blade needs by calling a SMITH expert or downloading this work sheet at www.SmithMfg.com/images/diamond.pdf
Premium Dry Cutting Saw Blades Ultra-Premium high performance diamond blades for dry-cut on AC and PCC substrates.
Groove Inlay
Widths: 0.118”, 0.125”, 0.145”, 0.160”, 0.230”, 0.250”, 0.375” * O.D.: 4” – 36” Grit: Coarse, Medium, Fine Bond: Soft, Medium, Hard *other sizes available
Diamond Grinding Discs
SMITH cutters (tungsten carbide, diamond and steel) are an “ultra-premium” grade, the industry’s highest quality manufacturing process and performance standard. SMITH flails, 4N1, cast, millers, picks and scrapers are preferred by professionals who want long life performance. Use 300s with SMITH Drums for guaranteed performance.
4N1 FULL-WIDTH AND SMITH 300 CARBIDE SPECIALTY FLAILS SMITH 1994 original design -revolutionary 4N1™ full-width cutter replaces 4 carbide flails and removes 4 ways: Erases, Cleans, Strips, and Mills.
PART # O.D.
6 Teeth CF2526 1.85” 0.61” 0.24”
8 Teeth CF2228 2.38” 0.79” 0.24”
16 Teeth CF4116 3.23” 1.04” 0.32”
Applications Shave, Groove, Grind, Route or Plungecut with SMITH blades engineered to provide the longest lasting performance for low or high powered equipment. Call SMITH for the matched blade sets for your next grinding project. Use with: All popular truck-mounted, self-propelled and walk-behinds for grooving, grinding and plunge-cut operations.
A C
A B C
W.10.20T (10”) Diamatic 200101 (9.45”) W.4.24T.NB (4.5”) W.7.24T.NB (7”) W.9.30T.NB (9”)
PART # O.D.
Use with: Most popular equipment, FS150, LNX8, X3, etc.
Diamond Grinding Plugs
Applications
*other sizes available
Diamond Grinding Block Inserts Only SMITH offers a 5-edge diamond segments to improve grinding speed. Sold in a rubberbushed mounting block to fit your equipment and applications. P/N W.EGD.19111A . . . . . General purpose 6 grit P/N W.EGD.19130A . . . . . Abrasive concrete 16 grit P/N W.EGD.19181A . . . . . Epoxy mortars 36 grit P/N W.EGD.19250A . . . . . Terrazzo grinding 50 grit P/N W.EGD.19260A . . . . . Terrazzo grinding 80 grit P/N W.EGD.19270A . . . . . Terrazzo grinding 120 grit P/N W.EGD.19280A . . . . . Terrazzo grinding 200 grit MADE IN USA
6
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
Est. 1990
Sizes are approximate. Other sizes available.
Applications Smooth rough surfaces or trowel marks. Remove thin coats of mastics, urethane, epoxy and more. Grind or polish terrazzo, granite and flint. Repair surface damage to concrete. Level high spots. Use with: All popular diamond-sert grinders. “5 edges are faster and last longer”
What customers say about SMITH “I save money with SMITH diamond saw packs. They cut dry, remove fast and last the longest.” L. Stedman
300’s general removal
PART # CF3001
O.D.
I.D.
WIDTH
1.06”
0.43”
1.37”
0.43”
3.26”
1.37”
0.43”
3.26”
1.37”
0.43”
(12 flail pins) 3.26”
300’s general removal
CF3002
(12 flail pins) 3.26”
CS3002
300’s groove/inlay removal
(12 saw tooth)
CC3002 (Flail/Saw combo)
300’s fast and hard removal
I.D.
WIDTH
PART # O.D.
8 Spike Flail CF2118 2.30” 1.00” 0.24” CF2128 2.30’ 0.79” 0.24” CF2618 2.30” 0.68” 0.24” CF2119 2.68” 1.03” 0.24” CF3158 3.26” 1.18” 0.32” CF3159 3.27” 1.03” 0.32” 12 Spike Flail CF3150 3.15” 1.02” 0.32” CF3151 3.15” 1.18” 0.32” CF3152 3.15” 1.30” 0.32”
12, 24, 30 segment turbo-style for fast grinding on concrete and asphalt. Segments can be configured in other patterns. Available with or without locking nuts.
*Don’t see your size - Call SMITH for help.
WIDTH
Select ultra-premium long life flail pin cutters for your toughest asphalt and concrete removal projects. Last up to two times longer than competitive cutters.
Applications
Size: 50mm x 10mm. Remove dry or wet, rough and uneven spots on Grit: Coarse, Medium, Fine concrete or terrazzo surfaces. Bond: Soft, Medium, Hard For aggressive or non-aggressive honing of concrete and terrazzo floors. E D P/N: W.DIA.SP44242 Use with: Floor grinders, preparators, prepmaster, E P/N: X3.00.442 terrco and other brands. D
I.D.
SMITH 300 ultra-premium life cutters lasts 300 hours. Add a SMITH cutter drum and the SMITH300 performance is guaranteed.
Guarantee-It ™
ULTRA-PREMIUM LIFE CARBIDE FLAILS
Grit: Coarse, Medium, Fine Grind high joints and rough, uneven surfaces, level Bond: Soft, Medium, Hard concrete and remove epoxy, urethane, paints and O.D.: 4.5”, 7”, 9”, 10”, 12” * toppings. Use with: Your floor grinders B
What customers say about SMITH
“We know it costs less to run our equipment with SMITH cutters and parts.” S. Vines
I.D.
Flail-It ™ WIDTH
8 Spike Round Flail CF1519 1.40” 0.47” 0.24” 5 and 6 Spike Flail CF2514 1.68” 0.63” 0.24” CF2516 1.85” 0.61” 0.24” CF2616 2.23” 0.68” 0.25” CF2116 2.25” 0.99” 0.24”
Mill-It ™
ULTRA-PREMIUM LIFE CARBIDE EDGE MILLERS We braze ultra-premium grade tungsten carbide to machined tool-steel millers in a proprietary process resulting in a cutter that removes thick film coatings, thermoplastics or asphalt fast.
5 or 6 Edge Scraper
PART # O.D.
CM2535 1.66” 0.60” 0.85”
I.D.
WIDTH
6 Edge Scraper
PART # O.D.
I.D.
WIDTH
CM3136 3.20” 1.03” 0.87” CM3137 3.20” 1.18” 0.87” CM3146 3.25” 1.03” 1.54” CM3147 3.25” 1.18” 1.54”
CM2150 2.25” 0.68” 0.87” CM2151 2.25” 0.79” 0.87”
SINTERED TUNGSTEN CARBIDE CAST SCRAPERS It starts with the finest tungsten carbide powders sintered in a precision cast mold providing a variety of cutters designed to remove mastics, plastics, epoxy, and paint on concrete or asphalt.
PART # O.D. I.D. WIDTH Scraper Squares CP2400 0.75” 0.25” 0.25” CP2401 0.75” - 0.19” CP2402 1.00” 0.38” 0.19” CP2403 1.00” 0.38” 0.38”
7 and 12 Edge Scraper CM2519 1.53” 0.53” 0.47” CM2520 1.68” 0.53” 0.47” CM2550 2.22” 0.87” 0.79”
PART # O.D.
I.D.
Scrape-It ™ WIDTH
15 Sided Stars CF0410 1.20” 0.45” 0.14” CF0413 1.85” 0.52” 0.21” CF0414 1.20” 0.45” 0.16” CF0411 1.20” 0.45” 0.21” with hub CF0412 1.20” 0.45” 0.20” 10 Sided, Angled CF0409 1.05” 0.47” 0.16”
12 Sided, Blunt CF0415 2.00”
0.61”
0.16”
Sizes are approximate. Other sizes available. (* Bold part numbers are cutters depicted)
MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
7
Ultra-Premium Cutters (cont.)
OEM Replacement Parts
Scan Code For Online Cutter Selection
MANUFACTURING
Cutters / Removers / Parts / Support
MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
(954) 941-9744
www.SMITHMFG .com
www.SMITHMFG .com
PART # O.D.
I.D.
PART # O.D.
Chase-It ™
WIDTH
Star (Sharp) HS1043 1.48” 0.53” .125” HS1053 1.65” 0.626” .125” HS1003 1.65” 0.64” .125” HS1004 2.00” 0.63” .160” HS1008 2.00” 0.79” .160” HS3002 3.00” 1.03” .197”
WIDTH
Beam (Blunt) HS1013 1.65” 0.64” .125” HS1000 2.00” 0.59” .156” HS1001 2.00” 0.78” .160” HS2024 2.38” 0.80” .160” HS2025 2.38” 1.03” .160” HS3001 3.02” 1.03” .187” HS3030 3.02” 1.18” .187”
“Cutters may look alike but don’t wear the same. We earn more on each job with the SMITH cutter vs. other brands.” M. Allen
I.D.
Saw-Tooth (Sharp) HS0010 1.00” 0.44” .125” HS0011 1.48” 0.64” .125” HS0012 1.24” 0.63” .125” HS0013 1.60” 0.64” .125” HS2687 2.00” 0.68” .625”
FORGED CARBIDE EDGE ROUTERS AND GROOVERS For fast cutting and long life, use SMITH brand cutters on your crack routing, joint cleaning, plunge-cut removal or grooving machines. PART # O.D. I.D. WIDTH no hub RP0058 3.63” 1.04” .358” SS0058 4.84” 1.01” .375”
PART # O.D. I.D. WIDTH with hub (.867) RP0158 3.63” 1.04” .358” SS0158 4.84” 1.00” .372” SS0138 6.50” 1.00” .372”
PREP-IT STRIPS™, DRUMS
Prep-It ™
SMITH Carbide Rubber Prep-It Strips™ offer a “shot-blast like finish” using a scarifier. PART # PREP-IT STRIP Drum For 8200.07 FS200, FR200, RT200, BMT 200
Typical Finish: CSP3 - 4 Action: Not Aggressive Surfaces: Concrete, Asphalt or Steel Best for: curing compounds, prep surfaces, paint, grease, oil, and flaky paints
11
™
PART # 107500 504.2090A 65059NA MR-7512A SW-7510A X3.00.101.00A
Wire Brush Assembly For SPS10 FS200, FR200, RT200, others SPS8, CPM8 MRL Grinders FS350, FS390, Stripe Eater Set of 6 cup discs, X3, LNX8
Applications: Remove curing compounds, oil and grease deposits while protecting the substrate. Typical Finish: CSP1 Surfaces: Concrete, Asphalt or Steel Best for: light removal (curing compounds, grease, oil, flaky paints)
2
3
4
ILL # 1 2 3 4 5 6 7 8 9 10 11
WHY SMITH? SMITH ultra-premium grade road planing bits work best on your orbital and rotary cold planers for asphalt milling, concrete planing, micro-surfacing or coating removal.
5
Erase-It PM3001
No Groove Removal PM3002
PM3000
MADE IN USA Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
Est. 1990
PART # ED3000 ED3001 ED3002 PM3000 PM3001 PM3002 LX3000 LX3518 LX3524 GX024 GX048
# PINS/SET NBC 72 Carbide 2 144 Carbide 2 216 Carbide 2 72 Carbide 3 144 Carbide 3 216 Carbide 3 48 Carbide 1 54 Steel 1 72 Steel 1 72 Carbide 2 144 Carbide 2
+
Finish CSP6 CSP5 CSP4 CSP6 CSP5 CSP4 CSP6 CSP6 CSP5 CSP6 CSP5
6
PART # MB-81 MB-83NB MB-28NB MB-28NS MB-89NS MB-66 MB-69 MB-68 CC81 CM-01 CM-02
7
8
Description Sharp tip for Bobcat, Ranjo, Alitec, etc. Blunt tip for Bobcat Alitec, Wirtgen Blunt tip for Wirtgen planers Sharp tip for Wirtgen planers Sharp tip for Bobcat, Ranjo, Alitec, etc. Sharp tip for Bobcat Alitec, Wirtgen Blunt tip with double wear guard Blunt tip style for Shebecki, cold-planers, etc. C-clip for MB-81 Weld-on block for ILL # 1,2,5,6 Block for ILL # 7-9
Mill-It ™
CARBIDE CUTTER HOLDER ASSEMBLIES Carbide Scrape-It-Away Holder SMITH 8 sided sharp scraper holder assemblies with CP2402 perform best on your grinders for removal of mastics, glues, plastics, epoxies and paints. Scrape-it Carbide set-up P/N: E-12400.2402A
Carbide Cutter Block Assemblies SMITH ultra-premium grade carbide cutter assemblies fit on your grinders and erasers. Best for removal of build-ups, prepping, texturing and cleaning.
Strip-It ™
A: Strip-it Block E-2G0410.15 B: Flail-it Block E-2G1519.15 C: Finish-it Block E-2G1043.14
A
B
C
SCABBLER BITS
Chip-It ™
Hard hitting SMITH brand Scabblers are preferred by OEMs and fit your Air Scabblers sold with mounting hardware. PART #
DESCRIPTION
SCAB.MA.5 SCAB.MA.9
5 Point for hard impact 9 Point for fine finish
DRUMS, SHAFTS AND SPACERS, BUSHING AND MORE
Only SMITH’s ultra-premium cutters contain the thickest and longest wearing cutter pin and body. All cutters, sold in sets of 3, come assembled with the longest-lasting, fail-safe, sealed ball bearings available. SMITH’s 216 and 144 pin cutters remove coatings without the grooving common when using other cutters. 16, 24, 48, 72 pin for thick film removal and thermoplastic markings, or for smoothing down high spots.
™
Plane-It ™
9 1
WIRE BRUSHES
ROTARY BIT CARBIDE AND STEEL PIN CUTTERS
8
10
What customers say about SMITH
Got Planers and don’t see your cutter size? Visit our website or call your SMITH Representative
CARBIDE ROAD PLANING BITS
TOOL STEEL CUTTERS - BEAM, STAR, SAW-TOOTH SMITH cutters are machined from high quality tool steel to close tolerances for even wear, easy set-up, and heat treated for long life. Select Beam for gentle removal, Stars for deeper substrate penetration and Saw-Tooth for aggressive removal.
Finish-It ™
Cure-It
Visit us at www.SmithMfg.com
Scan Code For More Information on Replacement Parts
OEM for TLR7 TLR7 TLR7 PMEraser, LNX8, GLC, X3 PMEraser, LNX8, GLC, X3 PMEraser, LNX8, GLC, X3 PMEraser, Linax PMEraser, Linax PMEraser, Linax HMS, 20H HMS, 20H
Sizes are approximate. Other sizes available. (* Bold part #’s are cutters depicted.) OEM listed models are not affiliated with SMITH. (+ NBC - # of bearings / cutter)
Need Parts? Ask for SMITH... • Bushed cutter drums with spider supports • Chrome plated toolsteel shafts • Wear-resistant drum bushings • Hardened plated spacers • Specialty wear components for your removal equipment
What customers say about SMITH
“I don’t own SMITH equipment yet but I buy SMITH cutters and drum assemblies for my scarifiers.”
B. Feller
MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
9
FS Compact Series™
IT!
Don’t Just Remove It...
MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Cutter Selection (page 5)
FS200D™Compact Scarifier/Grinder
Drums can be spaced inline with cutters to groove (G), or offset with no spacers (F), one spacer (M), two spacers (C) or three spacers (X) at full or narrow widths.
MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options Weight, Dimensions Removal Width, Depth Production Rate
Height-adjustable vibration tension setting with comfort grips
Cure-It
MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options Weight, Dimensions Removal Width, Depth Production Rate
Electric, Gas, Propane 150 lbs. (42”x14”x39”) ≤ 8” (1/8” pp) ≤ 400 SF (@ 1/8” pp)
www.SMITHMFG .com
FS050™Performance Edger Scarifier www.SMITHMFG .com
Electric, Pneumatic 12 lbs. (19”x8”x9”) ≤ 2” (1/16” pp) ≤ 100 SF (@ 1/16” pp)
FS150™Planetary Scarifier/Grinder MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options Weight, Dimensions Removal Width, Depth Production Rate www.SMITHMFG .com
Gas engine-kill safety lanyard and throttle control lever
All-steel construction with industrial powder coat
FS050™ Electric
Triple-drive belts with safety belt guard
Electric, Pneumatic 15 lbs. (20”x12”x11”) ≤ 7” (1/16” pp) ≤ 100 SF (@ 1/16” pp)
FS150™ Electric
FS050™ Air
FS150™ Air
On-board tool holder c/w tool kit
P/N: 504.2090 Dust free vacuum port
Prep-It
POWER OPTIONS
Strip-It
Comfortable reversible grips by hand or in upright caddy
5 or 9 HP Honda 6 or 9 HP Subaru
No-grease “maintenance free” drive bearings
P/N: 8200.02.7
4 or 6 shaft cutter set-up
2 HP 110/220V 3 HP 220V or 230/460V
Removable side plate for cutter access Hex drive shaft for easy side drum loading
POWER OPTIONS
9 HP Subaru
Fixed front wheel for straight line removal
P/N: 504.4021.5.2526.8F
Brush Drum Assembly
Flail-It
Scrape-it™
Finish-it™
Flail-it™
Scrape-it™
Finish-it™
Flail-it™
P/N: 5502.6.0411.2M
P/N: 5502.6.0011.2F
P/N: 5502.6.1519.2C
P/N: FS150.0411.M
P/N: FS150.0011.F
P/N: FS150.1519.M
P/N: 504.4021.5.2514.8C
Mill-It
Remove Closer with the optional edger
Front feathering wheel to smooth surfaces
Dual depth control settings (adjustable lever and micro depth knob)
FS200 Deluxe™ Performance Benefits
FS050™ Performance Benefits
P/N: 504.4021.5.2535.8C
Route-It
P/N: 504.4021.2516.1G
FS200 Deluxe™ is ideal for striping contractors to remove markings and as a surface preparation tool to improve adhesion.
FS209D™ is depicted with standard front wheel and 9 HP Honda eliminating sidewalk trip hazards fast with flail-it carbide cutters.
What customers say about SMITH
Narrow the cutter drum to 1/4” and use the Strip-it carbide 4N1 to chase random concrete or asphalt cracks.
“Hands down, the SMITH hand-held cutter drums are indestructible and the SMITH brand FS209 Propane is the best machine we own.” M. Klein
Finish-It
P/N: 504.4021.5.1013.8F
10
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
MADE IN USA
Est. 1990
Remove oil spots, flaking paints and surface build-ups on concrete or asphalt using the Prep-it Drum.
MADE IN USA
Est. 1990
Triple your productivity and save your back with the SMITH walk-behind depth and pressure control edging “Upright Caddy”.
Use the FS050™ or FS150™ to remove graffiti on walls, floors or ceilings.
“Unbelievable, my SMITH is so easy to remove concrete sidewalk trips fast. In under 30 minutes, we reduced a 3” wall of terror to our senior citizens down smooth.” J. Santos
MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
11
SPS Series™
RemoveFaster.com
All-Purpose Surface Preparator that grows as your needs do.
MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Cutter Selection (page 5)
Drums can be spaced inline with cutters to groove (G), or offset with no spacers (F), one spacer (M), two spacers (C) or three spacers (X) at full or narrow widths.
Height-adjustable multi-positional ergonomic comfort grip handlebar
SPS10™All-Purpose Surface Preparator MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options Weight, Dimensions Removal Width, Depth Production Rate www.SMITHMFG .com
Electric, Gas, Propane 250 lbs. (38”x19”x44”) ≤ 10” (1/4” pp) ≤ 700 SF (@ 1/8” pp)
SPS8™“Original Rugged Scarifier” MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options Weight, Dimensions Removal Width, Depth Production Rate www.SMITHMFG .com
Electric, Gas, Propane 225 lbs. (38”x19”x44”) ≤ 8” (1/8” pp) ≤ 500 SF (@ 1/8” pp)
EZOFF™Up-Cut Removal System MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options Weight, Dimensions Removal Width, Depth Production Rate www.SMITHMFG .com
Gas, Propane 450 lbs. (85”x34”x48”) ≤ 10” (1/4” pp) ≤ 1500 SF (@ 1/8” pp)
POWER OPTIONS Reversible handle controls
Cure-It
P/N: 107500
Strip-It
P/N: 1065051.75.2228.10F
Flail-It
Attaches to any Hydraulic Power Drivers
9 HP Honda 9 or 14 HP Subaru
Operator dashboard for speed controls, safety shutoff, disengage cam c/w deluxe 10-setting exclusive micro-depth knob
5 HP 110/220V 5 HP 230/460V
All-steel unitized heavy-duty construction, reinforced at stress points c/w industrial powder coat
14 HP Subaru
Two-stage cyclone air cleaner
POWER OPTIONS
Forward, reverse and side-to-side operation with and without optional Sulky Driver and hitch connection
Heavy-duty wide HTD drive belt with safety belt guard tensioned without moving motor
Dual 2” OD vacuum dust-collection ports
13 HP Honda 14 or 20 HP Subaru 5 HP 110/220V 7.5 HP 230/460V 14 or 20 HP Subaru
P/N: 1065051.75.2128.10C
SPS10.13
Scrape-It Removable side plate for side-loading drum with twin maintenance-free drive bearings and brush and chip guard
Twin in-line front with twin in-line front wheels with optional feathering caster wheel and pitch-control wheel extensions
SPS10.20
P/N: 1065051.75.2550.10C
Plane-It
P/N: SPS10.PD.66.32
Inlay-It
Heavy-duty bushed carbide and diamond cutter drums
Exclusive NO-Hard-Drop cradle shock engagement
Walk or ride operator control dashboard with optional tach/hour meter
Optional water tank with wet controls
Contractor-rated electric motors
SPS10 quick-mounts into Up-Cut carriage
Easy-access seated operator controls
Groove-It
Prep, Remove or Groove easier and faster using the EZOFF up-cut carriage with your SMITH SPS10 and Sulky driver
SPS10 Edge Line
Up-Cut Carriage
P/N: W.DB.11.0.8.25.21G
Finish-It
P/N: 1065051.75.1001.10F
12
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
EZOFF System with Sulky Driver
SPS8™ Performance Benefits:
SPS10 Deluxe™ Performance Benefits:
P/N: W.DB.11.0.7.25.38A
Get close to walls with Standard 4 up to 4” width cut edger outboard wheels for assembly consistent finish
Lifting Bar and Handle Removed Line
MADE IN USA
Est. 1990
Achieve CSP 3-9 surface textures when reducing high spots or removing coatings
Get close to walls with optional edger with diamond shaving or carbide scarifying drums
Achieve any finish with Flail-it, Strip-it, Mill-it, Plane-it, Scrape-it, Finish-it, Cure-it and diamond grooving and shaving drums
SPS Series features the no-bounce center-weight design for controlled finishes
Remove two times faster by upgrading to larger cutters, shafts, wheels and bearings
What customers say about SMITH “Our SMITH has been a great money maker for our rental business. Its our toughest scarifier that rarely needs servicing with cutters that never seem to wear out.” R. Barry MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
13
FS300™ Series Heavy-Duty Scarifiers MANUFACTURING
-IT!
Heavy-Duty 15” Manual, Self-Propel or Skid-Attach Scarifiers, Planers & Shavers
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Cutter Selection (page 5)
FS390h™Shaver/Planer/Scarifier Attachment
Drums can be spaced inline with cutters to groove (G), or offset with no spacers (F), one spacer (M), two spacers (C) or three spacers (X) at full or narrow widths.
MANUFACTURING
Power Options Weight, Dimensions Removal Width, Depth Production Rate Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
POWER
Shave-it™ Groove-it™ Cure-it™
FS350™Self-Propelled Surfacer MANUFACTURING
Power Options Weight, Dimensions Removal Width, Depth Production Rate
13-45 HP, low or high flow hydraulic 525 lbs. (48”x28”x46”) ≤ 15.3” (3/8” pp) ≤ 1200 SF (@ 1/8” pp)
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Bobtach mount plate
Power Options Weight, Dimensions Removal Width, Depth Production Rate Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Electric, Gas, Propane 450 lbs. (48”x28”x46”) ≤ 15.3” (3/8” pp) ≤ 850 SF (@ 1/8” pp)
POWER OPTIONS
• 8” drive wheels for superior traction • Lifting carriage for easy maneuverability
Boom Car with exclusive Pitch and Roll capability for superior removal in all grades and pitches
MANUFACTURING
Electric, Gas, Propane 490 lbs. (47”x22”x46”) ≤ 15.3” (3/8” pp) ≤ 1000 SF (@ 1/8” pp)
• Optional touchscreen PLC electronics
Custom hydraulic manifold for cool motor operation (controls both pressure and flow to hydraulic motor)
FS300™ Heavyweight Surfacer
13 HP Honda 14 or 22 HP Subaru 7.5, 10 HP 230/460V 20 HP 230/460V 25 HP Subaru
Steel frame motor protection cage
Reversible (Cast Iron Hydraulic motor with flat face) “Quick Disconnects” for “up” or “down-cut” operations
Removable cutter drum access side plate
Plane-it™ Remote hydraulic height control with lockable hard stops
Flail-it™ Three heavy duty wheels for superior turning during operations
Strip-it™
• Control finish, speed and depth on concrete or asphalt • Attaches to low-flow or high-flow hydraulic units • Multiple cutter and diamond shaver drums • Heavy-duty all-steel construction • Maintenance-free triple-sealed bearings
Cuts prep time with 20 HP high or low-speed severe-duty rated motor and variable-speed hydrostatic drive with forward/reverse lever controls
FS3 Series™ Performance Benefits:
What customers say about SMITH
Finish-it™
“We use SMITH diamond grooving blades because they cost less to use and cut faster than any brand we tried. We groove miles of various cut widths of up to 8” wide at 200 mil deep. The last set of blades lasted over 690,000 LF on medium hard concrete at a running rate of 900 LF/hr. No other company can match SMITH’s performance and price.” G. Cheever
Guarantee-it™
“I have been a fan of SMITH Manufacturing for over 10 years, SMITH has always provided excellent service, a great machine and even better cutters. I am impressed with SMITH and look forward to trying their next productivity enhancer.” R. James MADE IN USA
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
SMITH FS350 Shaver/Scarifier
FS390h™ Performance Benefits:
Mill-it™
14
Heavy duty belt guard, housing with oversized drive bearings
Est. 1990
Order your FS350™ for Diamond Shave-it or Groove-it use (high RPM), or for scarification, milling or planing removal (low RPM) operations.
What customers say about SMITH “We are very satisfied with our SMITH FS300, and it performs as advertised. We have prior experience with an Edco machine to compare with, and the SMITH works better in a confined area with lower emissions, and also removes faster and easier with a wider cut path.” T. Wright
• Quick-setting locking depth control spring-mounted lever with rotary micro depth drum engage/disengage, adjustable dual spring-lifting controls • All-steel heavy-duty formed construction with industrial powder coat with heavy-duty vibration mount long-life maintenance-free sealed bearings • Large dust control ports with optional wet controls and water tank • Vibration-dampening ergonomic height-adjustable handlebar with all operational controls (start/stop, depth, speed) in easy reach • Dual rear heavy-duty non-marking wheels with brake, plus single front or optional dual adjustable wheels for working on variable surface conditions • Positive Control HTD drive belt with tension MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
15
X Eraser Series™ MANUFACTURING
RemoveFaster.com
When you need to REMOVE without GROOVES
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
1™No-Groove Planetary Eraser
LNX8™ No-Groove Line Eraser
Cutter Selection - page 5 Equipment Specs - page 19
MANUFACTURING
“When you must remove without grooves.”
Cutters / Removers / Parts / Support
(954) 941-9744
Power Options 13-45 HP, low or high flow hydraulic Weight, Dimensions 480 lbs. (27”x18”x24”) Removal Width, Depth ≤ 8” (1/8” pp) Production Rate ≤ 1000 SF (@ 1/8” pp)
www.SMITHMFG .com
Power Options Weight, Dimensions Removal Width, Depth Production Rate
Gas, Propane, Electric 450 lbs. (47”x31”x40”) ≤ 8” (1/8” pp) ≤ 800 SF (@ 1/8” pp)
NO GROOVING UNDULATIONS GHOST LINES
Erase-It
The easy rolling, beveledge tri-cut rotary scaping/smoothing erasing action will not groove or undermine the surface like scarifiers, planers and waterblasters.
POWER
3™Triple-Head No-Groove Eraser Power Options Gas, Propane, High-Flow Hydraulic Weight, Dimensions 680 lbs. (60”x46”x40”) Removal Width, Depth ≤ 24” (1/8” pp) Production Rate ≤ 2400 SF (@ 1/8” pp) The SMITH X3 is powered by 22 HP gasoline, 25 HP propane or high-flow (3,000 psi, 28 gpm) hydraulic motors
POWER OPTIONS
POWER OPTIONS
72, 144, 216 pins
P/N: 169068.3000 P/N: 169068.3001 P/N: 169068.3002
13 HP Honda 7.5, 10 HP 230/460V
Cure-It
14 HP Subaru
3 rotary spindles remove up to three times faster than single-head removers and up to 24’ widths
P/N: X3.00.101A
Plane-It
Performance Benefits of X3™ and X1™ Erasers Optional front push/pull bar for 4” to 24” widths
P/N: X3.00.120.66A
DINGO
Adjustable spring-tensioned removal tool height and pitch control with floating terrain-following suspension for beveled finishes
PICK-UP/VAN
TRUCK
SKIDLOADER
LNX8™ Performance Benefits:
Grind-It
P/N: X3.00.442A
Smooth-It Walk-behind, drive or skid-attach options
P/N: X3.1043.14A MADE IN USA
16
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
Est. 1990
•D ashboard with choke, start and stop controls •S wing-style adjustable anti-vibration handle •C ontrol cutter pitch, depth and pressure to erase on all surfaces •M aintenance-free bearing and dual tensioned drive •D ust and debris control with vacuum port •T ilt-up chassis for cutter access • Cutter pitch spindle leveler • Twin removable 45 lb. weight ballast (optional add-on plates) • Optional electric start • All-steel rugged construction powder coat •1 0-position micro depth and engage/ disengage cam with shock cradle
Bobtach side-shift bracket standard, optional custom truck-mount pods WHY SMITH Erasers leave No-Grooves and Undulations? The unique suspension of the X1™ or X3™ keeps the removal tools parallel and at a preset height from the removal surface regardless of road irregularities. The removal tools are held at a fixed angle to the road surface, permitting a simultaneous vertical and horizontal floating removal action. The X1™ and X3™ breaks up the markings and scrapes across the surface at the same time leaving an erased appearance with the substrate beveled edges feathered by the rolling action, eliminating grooving and undulation patterns.
BEFORE
What customers say about SMITH “We purchased a SMITH X3 instead of a waterblaster or grinding truck to remove the airfield markings on the island of Ascension, one of the most remote locations on earth. After many months of exhaustive research we concluded the SMITH X3 equipment will meet the remedial expectations of the Air Force considering the beginning/ending surface conditions. Set up and operational confidence in the SMITH X3 allowed us to establish and achieve completion goals while flight operations continued. The final surface was removed of markings without unsightly grooving or undulations for same day re-stripe.” W. Kirk
AFTER w/VACUUM
MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
17
What customers say about SMITH
Remover Essentials to help you remove Faster, Safer, Cleaner MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744
Equipment Specifications MANUFACTURING
Cutters / Removers / Parts / Support
(954) 941-9744 www.SMITHMFG .com
Optional severe duty hydraulic cooling system All-steel construction
Plane-it (carbide picks)
D
E
E
GP GP
Strip-it (4N1 full-width carbide) Flail-it (carbide flails)
D
D
E
E
E
U
D E
GP GP GP GP GP
Mill-it (carbide millers)
D D E
H
GP
Scrape-it (carbide scrapers) Finish-it (beam or stars) Prep-it (carbide strips)
Removal width/pass (< inches) Removal depth/pass (< inches)
SCAN AND DOWNLOAD: Top 10 Reasons to Buy a SMITH Sulky Driver
1/8 1/8
1/8 1/8 1/4 1/4 3/8
3/8 3/8
8 12
14 14
19 19 19 34 28
22 28
Length (inches)
19 20
42 42
38 38 38 85 47
47 48
Weight (lbs)
12 15
125 150
225 225 250 450 450
490 525
.25 .25
.50 .75
.75 .75 .75 6
(without drum, attachments)
Est. 1990
1200
Width (inches)
1000
46 46
850
44 44 44 48 48
1500
39 39
700
400
11
500
100
9
400
100
Height (inches)
4
4
4
25 mm
Cut distance to wall (in inches)
25 mm
Variable depth adj + Engage cam lever ( )
Pressure controls + Weight plates ( )
Qty wheels + Feathering caster ( Optional water controls
Tank (
)
3/4”
Bushed drums)
3/4”
Cutter shaft OD (
20/25 mm
Vacuum Port w/Containment shroud
3
3
4
4
4
4
3or 4
)
3or 4 3
R
R
R
E
H
H
GP GP GP
8
8
24
1/8 1/8 1/8
40 24 40 31 18 46 47 27 60 450 480 680
8
6
6
4
4
4
Remote power shut-off
Vibration Dampening Handlebar Easy Drum Access (S-sideplate, L-lift unit)
S
L
S
S
L
S
S
S
S
S
S
L
L
L
Direct (D) or Belt-drive (B) system
D
D
B
B
B
B
B
B
B
B
B
B
D
B
Bearings Sealed(1) or Serviceable(2)
1
1
1
1
2
1
1
1
1
1
1
1
1
1
O
O
O
O O
O O
S
M
M M
R M
S
M
R
R
Manual, Self-Propel or Ride-on MADE IN USA
8
Hourly Production rate (SF) (approx.)
Parking Brake–Standard vs. Optional
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
8
3/4”
MV Dust Collector Performance Benefits: ™
15 15
8
1/2”
Engine protection bar
1/16 1/16
10 10 15
8
1/2”
Forward and reverse speed foot controls, hydrostatic transmission
Rugged swivel casters
Heavy-duty trailer with tow package
7
1/2”
Impeller protection screen
2
10 mm
20” D x 30” H collector bag
Standard Specifications and Available equipment options
Dual collector ports fits all saws, grinders, scarifiers, line removers
Optional LED strobe and running lights
(^ swivel engaged)
10 mm
1350CPM Air Flow 9.5” Static Pressure
500
Cure-it (wire brush packs)
Multiple position hitch plate and couplers for any push models
Key start c/w sealed battery
18
D
2400
2 HP 110/220V
Shave/Groove-it (diamond packs)
D
1000
Keep working with the optional 1 micron filter with shake down bar as shown. (5 micron upper and lower bags come standard)
5.5 HP Honda 6 HP Subaru 5 HP Honda 6 HP Subaru
EA EA
Erase-it (24, 48, 72 carbide pins)
POWER OPTIONS
POWER
Gas (G), Propane (P)
R
800
Deluxe high-back padded seat, adjustable forward and back controls. Seat tilts forward for access to tanks.
Electric (E), Air (A), Hydraulic (H)
D
Walk-Behind/Ride-on “No-Groove” Traffic Line Removal and Surface Prep (with available bobtach or truck mount attachments)
Power Options Gas, Electric Weight, Dimensions 160 lbs. (42”x18”x72”) Turbine Speed ≤ 1350 CFM
5, 6 HP Gas 280 lbs. (40”x34”x44”) Walk-behind machines ≤ 10 mph
Cutter Rotation (Down, Up, Rotary)
Walk-Behind/Self-propelled Heavy-Duty
Power Options Weight, Dimensions Mounts to Production Rate
www.SMITHMFG .com
Walk-Behind/Ride-On: All-Purpose
(954) 941-9744
Walk-Behind– Light-Weight
“Removes dust and debris all day.”
Cutters / Removers / Parts / Support
www.SMITHMFG .com
Hand Held
MANUFACTURING
“When you need to Do-it Faster.”
(954) 941-9744
Drum Rotation Power Options
MV Dust Collector™
MANUFACTURING
Cutters / Removers / Parts / Support
Cutter Drum/tool choices
LLR.6 Sulky Driver™
FS 05 FS 0 15 0 FS 20 FS 0 D 20 9D SP S8 SP S SP 8 D S EZ 10D O FS FF 30 0 FS 35 FS 0 39 0h LN X X1 8D X3
www.SMITHMFG .com
Optional front wheel steering kit and tow package
“I always recommend a SMITH to my customers because of their excellent reputation as a first class cutter and machine manufacturer. They are also very knowledgeable and available to help my customer get the right cutter or part for the job.” H. Strange
M M
M M
R
MADE IN USA
Est. 1990
Specifications and data are subject to change without notice. © SMITH Manufacturing Co. 2013
19
MANUFACTURING
Manufacturing Co. Inc.
Cutters / Removers / Parts / Support
Cutters / Removers / Parts / Support
(954) 941-9744
SMITHMFG 1610 S. Dixie Highway Pompano Beach, FL 33060 1-954-941-9744
[email protected] www.
.com
#
with our Customers?
1
MADE IN USA
Est. 1990
Your Equipment + SMITH Cutters = RemoveFASTER Spalled Floor or Failing Slurry Cap
Texturize Surfaces
Concrete Risers, Deflections, or Curled Joints
Level Trip Hazards
Profiling For Overlays
SMITH Surfaces For Striping
Uneven Surfaces or Floor Undulations
Route or Chase Cracks
Failed Coatings, Contaminants, Coverings or Overlays
Remove Cures and Sealers
Exposing Aggregate to Seal, Densify, or Polish
Eradicate Surface Marks
Cleanup For Coatings or Polishing
Peel Off Glues and Mastics MADE IN USA
Est. 1990
RemoveFaster.com Scan the QR code below to see our online catalog We Know Removal is Hard Work SMITH helps to make your job easier, faster and cost-effective
www.RemoveFaster.com
Don’t Just Remove It...
IT! RemoveFaster.com