MADE IN THE USA

BACKFLOW PREVENTERS

Backflow Preventers

TABLE OF CONTENTS Products

Model

Ordering Code

Selection Guide

Page 3

Double Check Valve

DC-4A

4A-100

4

Double Check Valve

DC-40

40-100

5

Double Check Valve

DC-4S

4S-100

6&8

Double Check Valve

DC-4SG

4SG-100

7

Double Check Detector Assembly

DCDA-4SG

4SG-600

9

Double Check Detector Assembly

DCDA-4S

4S-600

10

Reduced Pressure Principle

RP-4A

4A-200

11

Reduced Pressure Principle

RP-40

40-200

12-17

Defender Reduced Pressure Principle

RP-4D

4D-200

18

Reduced Pressure Detector Assembly

RPDA-40

40-700

19-20

Defender Reduced Pressure Detector Assembly

RPDA-4D

4D-700

21

Atmospheric Type Vacuum Breaker

AVB1

38-100

22

Atmospheric Type Vacuum Breaker

AVB2

38-200

23

Pressure Vacuum Breaker

PVB-4A

4A-500

24

Freeze Resistant Pressure Vacuum Breaker

PVB-4V

4V-500

25

Spill Resistant Pressure Vacuum Breaker

SVB-4W

4W-500

26

Dual Check w/Atmospheric Port

DCAP

40-400

27

Dual Check Valve

DUC-4N

4N-300

28

Dual Check Valve

DUC-4FP

DUC4FP

29

Dual Check Valve

DUC-40

40-300

30

Carbonated Beverage Backflow Preventer

CBBP

4C-100

31

Hose Connection Vacuum Breaker

HBV

38-300

32

Anti-Freeze Hose Connection Vacuum Breaker

HBVB

38-400

32

Hose Connection Dual Check

HBDUC

38-300

33

Lab Faucet Dual Check

LFDUC

38-500

33

Freeze Protection Valve

FPV

40-000

34

“Y” Strainers

YB, YSCF

59 & 125YF

35

Thermal Expansion Valve Hose Connection Pressure Gauge

EXV HCPG

78-RV W-8078

36 37

Test Kits

TK

40-200-TK

37

Test Kit Accessories

TKF

40-000-TFK

37

Air Gap Drain

AGD

40-200-X1

38

Flanged Ball Valve

IBVE

IBVE

39

FP Hydro Ball Valve with Double Female NPT

7B-100

7B-100

40

FP Hydro Ball Valve with Male x Female Connections

7B-800

7B-800

40

Brass & Bronze Instrumentation Ball Valve

78-290

78-290

40

®

®

Backflow Shut-Off Valves

41

Available Shut-Off Valve Options

42

Product Approvals

43

Warranty and Limitations of Liability

43

2

Customer Service 1-704-841-6000

Backflow Preventers

SELECTION GUIDE APPLICATION TYPE OF DEVICE

SERIES

BACK BACK CONTINUOUS LOW HIGH PAGE SIPHONAGE PRESSURE PRESSURE HAZARD HAZARD NO.

DC-4A DC-40 DC-4S DC-4SG

4 5 6&8 7

DOUBLE CHECK DETECTOR ASSEMBLY

DCDA-4SG DCDA-4S

9 10

REDUCED PRESSURE PRINCIPLE

RP-4A RP-40 RP-4D

11 12-17 18

REDUCED PRESSURE PRINCIPLE (N & Z Flow)

RP-40-N RP-40-Z

13 13

REDUCED PRESSURE PRINCIPLE (Stn.Steel)

RP-40-S

17

REDUCED PRESSURE DETECTOR ASSEMBLY

RPDA-40 RPDA-4D

19-20 21

AVB1 AVB2

22 23

PRESSURE TYPE VACUUM BREAKER

PVB-4A PVB-4V

24 25

SPILL RESISTANT PRESSURE VACUUM BREAKER

SVB-4W

26

DUAL CHECK W/ ATMOS.PORT

DCAP

27

DUC-4N DUC-FP DUC-40

28 29 30

CARBONATED BEVERAGE BACKFLOW PREVENTER

CBBP

31

HOSE CONNECTION VACUUM BREAKER

HBV2

32

ANTI FREEZE HOSE CONN. VACUUM BREAKER

HBVB

32

HOSE CONNECTION BACKFLOW PREVENTER

HBDUC

33

LAB FAUCET VACUUM BREAKER

LFDUC

DOUBLE CHECK VALVE

ATMOSPHERIC TYPE VACUUM BREAKER

DUAL CHECK VALVE

*

33

* Limited back pressure to 10’ head

www.apollovalves.com

3

Double Check Valve Backflow Preventers

DC-4A Series TOP ENTRY DOUBLE CHECK VALVE ASSEMBLY The Apollo MODEL DC4A Double Check Valves are designed to prevent contamination of the potable water supply due to back-siphonage or backpressure from substances that are objectionable, but non-health hazards. The modular check valve cartridges have replaceable seats and reversible silicone seat discs. Apollo ball valve shut-offs with stainless steel handles and nuts are standard.

OPERATION During normal flow conditions, the two check valves are held off their seats, supplying water downstream. Each check valve is designed to maintain a minimum of 1 psi across the valve during normal operation. Should the downstream pressure increase to within 1 psi of supply pressure, both check valves will close to prevent a backflow condition.

Sizes 1/2", 3/4”, 1", 1-1/4", 1-1/2", 2"

FEATURES MATERIALS Body Caps Check Valves Springs Seat Discs O-rings Ball Valve Handles

Cast Bronze C84400 Cast Bronze C84400 Glass-Filled PPO 300 Series Stainless Steel Chloramine-resistant Silicone Chloramine-resistant EPDM Stainless Steel

ORDERING CODE Y-STRAINER 0-Standard 1-w/ Y-strainer (shipped loose) Example: 4A-104-T4LL = 3/4” double check valve assembly with union ball valves with locking lever handles

• • • •

Low pressure loss Modular cartridge check valves Compact yet easy to maintain Apollo ball valves w/ SS handles & nuts standard • Top access for testing, fast repair and maintenance • Corrosion resistant • No special tools required

• Chloramine-resistant elastomers • Patent pending • ASSE 1015 horizontal and vertical flow up • Maximum working pressure 175 psi • Temperature range 33°F - 180°F • Designed, manufactured, assembled and tested in South Carolina, USA

4A - 1 X X - TXX SIZE 3-1/2” 4-3/4" 5-1" 6-1-1/4" 7-1-1/2" 8-2"

SHUT-OFF VALVES 1-less ball valves 2-w/ball valves (Standard) 4-w/union ball valves

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks LL-locking lever handles

Flow Curves : Pressure loss vs. flow data as determined by independent approval agencies.

C

B A

Dimensions (in) Ordering No. 4A-103-T 4A-104-T 4A-105-T 4A-106-T 4A-107-T 4A-108-T

4

(mm) Model No. DC4A12 DC4A34 DC4A1 DC4A114 DC4A112 DC4A2

Size 1/2” (15) 3/4” (20) 1” (25) 1-1/4” (32) 1-1/2” (40) 2” (50)

A 10-3/4 (275) 12-1/2 (318) 15-1/4 (387) 18 (460) 18-5/8 (470) 21-1/2 (546)

B 7-3/8 (187) 8-1/2 (215) 9-1/2 (241) 11-3/4 (298) 11-5/8 (295) 12-3/4 (324)

Customer Service 1-704-841-6000

C 3-1/8 (80) 3-3/8 (85) 3-7/8 (98) 4-3/8 (111) 4-3/8 (111) 4-7/8 (124)

D 2-3/8 (60) 3 (75) 3-1/4 (83) 4-1/4 (108) 4-3/4 (120) 5-3/8 (136)

Net Wt. lbs.(kg.) 4.4 (2.0) 6.0 (2.7) 10 (4.5) 14 (6.4) 17 (7.7) 25.4 (11.5)

Double Check Valve Backflow Preventers

DC-40 Series TOP ENTRY DOUBLE CHECK VALVE ASSEMBLY The Apollo DC-40 Series Top Entry Double Check Valve Assembly is designed to protect against backflow from a cross-connection of non-health hazard pollutant. Within the assembly are two mechanically independent, spring-loaded poppet type check valves set in an integral cast bronze body. Both check valves are designed at an inclined angle upward from horizontal centerline of the assembly, and all test cocks are mounted at the top to assure easy access during repair and maintenance when unit is installed in a pit or tight places.

OPERATION Sizes 3/4", 1", 1-1/4", 1-1/2", 2"

MATERIALS Body and covers Springs Poppets Seat discs Replaceable seats Fasteners Ball valve handles

During normal flow conditions, the two poppet check valves are held off their seats, supplying water downstream. Each check valve is designed to maintain a minimum of 1 psi across the valve during normal operation. Should the downstream pressure increase to within 1 psi of supply pressure, both check valves will close to prevent a backflow condition.

FEATURES Bronze Stainless Steel Glass-Filled Celcon Silicone Rubber Glass-Filled Noryl Stainless Steel Stainless Steel

• Top access for testing, fast repair and maintenance • Corrosion resistant • Low head loss • Interchangeable poppets and springs • Replaceable seats & Reversible Seat Discs • Approved for horizontal installations

ORDERING CODE -

Example: 40-104-T4LL = 3/4” double check valve assembly with union ball valves with locking lever handles

Y-STRAINER 0-Standard 1-w/ Y-strainer (shipped loose)

• • • • •

CSA USC FCCCHR AWWA C-510 ASSE 1015 Comes standard with Apollo® full port ball valves with stainless steel handles • Maximum working pressure 175 psig • Temperature range 33°F-180°F • Designed, manufactured, assembled and tested in South Carolina, USA

40 - 1 X X - TXX SIZE 4-3/4" 5-1" 6-1-1/4" 7-1-1/2" 8-2"

SHUT-OFF VALVES 1-less ball valves (UL Classified) 2-w/ball valves (Standard) 4-w/union ball valves

Flow Curves :

Dimensions - in(mm) - Weights - lbs.(kg) Model No. DC4034 Ordering No. 40-104-T Body Size 3/4” (20) A 13 (330) B 7-1/4 (185) C 4-5/16 (110) D 1-5/8 (41) E 2-7/16 (62) F 5-7/16 (138) G 13/16 (20) Test Cocks 1/8 x 1/4 NPT Net Weight 8.8 (4.0) Shipping Weight 10.1 (4.6)

DC401 40-105-T 1” (25) 14-3/4 (375) 7-1/4 (185) 4-5/16 (110) 1-7/8 (48) 2-7/16 (62) 5-7/16 (138) 13/16 (20) 1/8 x 1/4 NPT 9.5 (4.3) 10.8 (4.9)

DC40114 40-106-T 1-1/4” (32) 20-3/4 (525) 12-3/8 (315) 6-1/8 (155) 2-3/16 (56) 3-13/16 (97) 6-3/8 (162) 1-3/8 (35) 1/4 x 1/4 NPT 23.2 (10.5) 25.9 (12.0)

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks LL-locking lever handles

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

DC40112 40-107-T 1-1/2” (40) 21-3/8 (545) 12-3/8 (315) 6-1/8 (155) 2-5/8 (67) 3-13/16 (97) 6-3/8 (162) 1-3/8 (35) 1/4 x 1/4 NPT 25.7 (11.7) 28.8 (13.1)

DC402 40-108-T 2” (50) 23-1/8 (590) 12-3/8 (315) 6-1/8 (155) 3 (75) 3-13/16 (97) 6-3/8 (162) 1-3/8 (35) 1/4 x 1/4 NPT 31.5 (14.3) 35.5 (16.1)

5 www.apollovalves.com

Double Check Valve Backflow Preventers

DC-4S Series (Previously Model DC) TOP ENTRY DOUBLE CHECK VALVE ASSEMBLY The Apollo DC-4S Top Entry Double Check Valve Backflow Preventer is designed to prevent backflow by either back-pressure or back-siphonage from a cross-connection between potable water lines and substances that are objectionable, but not a health hazard. It is an economical device that is easily repaired in the line. The device consists of two independently acting, springloaded poppet type cartridge check valves in an integral cast bronze body. Four test cocks and two shut-off valves which are quarter-turn, full-port, resilient-seated and ball type complete the assembly.

OPERATION

Sizes 1/2"

FEATURES

MATERIALS Body and Cover Check Modules Spacer Ball Valve Handles

During normal flow conditions, the two check valves are held off their seats, supplying water downstream. Each check valve is designed to maintain a minimum of 1 psid across the valve during normal operation. If at any time the pressure downstream of the device increases to within 1 psi of supply pressure, both check valves will close to prevent a backflow condition from occurring.

Bronze Acetal w/Stainless Steel Springs Stainless Steel Stainless Steel

Contact local water authorities for installation/service requirements.

• • • • •

Corrosion resistant Easy to install, repair and maintain Low head loss Replaceable check cartridge modules Comes standard with Apollo® full-port ball valves with stainless steel handles • USC FCCCHR • AWWA C-510

ORDERING CODE -

• ASSE 1015 • Approved for vertical and horizontal installations • Maximum working pressure 175 psig • Operating temperature range 33°F-180°F • Designed, manufactured, assembled and tested in South Carolina, USA

4S - 1 0 3 - A XX SHUT-OFF VALVES 1 -less ball valves 2 -w/ ball valves (standard) 4 -w/union ball valves

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks LL-locking lever handles

Example: 4S-103-A2 = 1/2” double check valve assembly with ball valves

Flow Curves :

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. DC4S12 Ordering No. 4S-103-A Body Size 1/2"(15) A 9-3/4 (250) B (w/o Ball Valves) 5-5/8 (143) C 4-1/2 (115) D 3-1/2 (90) E 1 (25) F 3-5/8 (92) Net Wt. (w/o Ball Valves) 2.68 (1.2) Net Wt. (with Ball Valves) 4.38 (2.0) Shpg. Wt. (w/o Ball Valves) 3.8 (1.7) Shpg. Wt. (with Ball Valves) 5.1 (2.3)

6

Customer Service 1-704-841-6000

Double Check Valve Backflow Preventers

DC-4SG Series DC-4SG SERIES DOUBLE CHECK VALVE ASSEMBLY The Apollo® DC-4SG Series Double Check Valve is designed to prevent contamination of the potable water supply due to back-siphonage or backpressure from substances that are non-health hazards. The modular check valves have replaceable seats and reversible EPDM seat discs. Grooved connections on an epoxy-coated ductile iron body allow for easy connection to butterfly valves or gate valves.

FEATURES • • • • • • •

Sizes 2-1/2”, 3", 4", 6", 8" MATERIALS Body Covers (2-1/2” - 6”) Covers (8”) Check Valves (2-1/2” - 6”) Check Valves (8”) Springs Seat Discs Test Cock Handles

Epoxy-coated (FDA) Ductile Iron Epoxy-coated (FDA) Steel Epoxy-coated (FDA) Ductile Iron Glass-Filled Noryl® Bronze Stainless Steel Chloramine-resistant EPDM Stainless Steel

Lightweight Short lay length Low pressure loss Modular check valves Individual access to check valves Reversible/replaceable seat discs Approved for vertical (up) and horizontal installations • Corrosion resistant epoxy-coated ductile iron body

SIZE 9 - 2-1/2” 0 - 3” A - 4” C - 6” E - 8”

Example: 4SG-10A-07 = 4” size with OS&Y flanged x grooved shut-off valves **Post indicator option not available in 2-1/2” size

Model No. Ordering No. Size A (Butterfly Valves)* A (Gate Valves)* B (Grooved End Body) C (Butterfly Valves) C (OS&Y Open) D (Butterfly Valves) D (Gate Valves) E (Butterfly Valves) E (Gate Valves) H (Post Indicator Valve) Test Cocks (NPT) Net Wt. (Less Valves) Net Wt. (w/Butterfly Valves) Net Wt. (w/OS&Y Valves)

SHUT-OFF VALVES (Inlet x Outlet) FLOW (OPTIONAL) 1 - Less Shut-off Valves (grooved-end body) N -N Flow 2 - NRS Flg x NRS Flg 3 - OS&Y Flg x OS&Y Flg 4 - OS&Y Flg x Monitored Butterfly Valve Grv 6 - OS&Y Flg x Flg Post Indicator** 7 - OS&Y Flg x OS&Y Grv 8 - OS&Y Grv x OS&Y Grv 9 - Mon. Butterfly Vlv Grv x Mon. Butterfly Vlv Grv 10 - OS&Y Flg x Grv Post Indicator**

Dimensions - in(mm) - Weights - lbs.(kg) DC4SG212 DC4SG3 DC4SG4 4SG-109 4SG-100 4SG-10A 2 1/2"(65) 3"(80) 4"(100) 29 (737) 29 1/2 (749) 29 3/4 (756) 33 (838) 34 1/2 (876) 32 (813) 17 (432) 16 1/2 (419) 17 (432) 8 (200) 8 1/2 (216) 9 1/4 (235) 16 3/8 (416) 18 7/8 (479) 22 3/4 (578) 4 1/2 (114) 4 1/2 (114) 4 1/2 (114) 3 1/2 (89) 3 3/4 (95) 4 1/2 (114) 9 (229) 9 (229) 9 1/2 (241) 9 5/8 (244) 10 3/8 (264) 11 7/8 (302) 14.75 (375) 14.80 (376) 14.80 (376) 1/2 1/2 1/2 53 (24) 53 (24) 53 (24) 80 (36) 83 (38) 97 (44) 149 (68) 174 (79) 208 (94)

www.apollovalves.com

Gate valves epoxy coated (FDA) ASSE 1015 CSA USC FCCCHR AWWA C-510 UL Classified FM approved US Patents #5,711,341 and #6,343,618 MADE IN THE USA

4SG - 1 X X - 0 X - X

ORDERING CODE Y-STRAINER 0 - None (Standard) 1 - With Y-Strainer (Flanged only, shipped loose)

• • • • • • • • •

DC4SG6 4SG-10C 6"(150) 32 (813) 39 (991) 18 (457) 10 1/4 (260) 30 1/8 (765) 4 1/2 (114) 5 1/2 (140) 12 (300) 14 5/8 (371) 18.75 (476) 3/4 60 (27) 128 (58) 309 (140)

DC4SG8 4SG-10E 8”(200) 43 (1092) 50 (1270) 27 (686) 12 (300) 37 3/4 (959) 6 1/2 (165) 6 3/4 (171) 15 (381) 16 3/4 (425) 23.42 (595) 3/4 375 (170) 506 (230) 852 (386)

*Nominal dimensions are shown. Allowances must be made for manufacturers’ tolerances.

7

Double Check Valve Backflow Preventers

DC-4S Series (Previously Model DC) DOUBLE CHECK VALVE ASSEMBLIES The Apollo DC-4S Double Check Valve Backflow Preventer is designed to control crossconnections between potable water lines and substances that are objectionable, but not a health hazard. It is an economical device that is easily repaired in the line. The device consists of two independently acting, spring-loaded swing type check valves in a corrosion resistant ductile iron body. The unit is available with inlet and outlet shutoff valves. Four test cocks, three on the check valve body and one on the inlet shutoff valve, complete the assembly.

OPERATION During normal flow conditions, the two check valves are held off their seats, supplying water downstream. Each check valve is designed to maintain a minimum of 1 psi across the valve during normal operation. If at any time the pressure downstream of the device increases to within 1 psi of supply pressure, both check valves will close to prevent a backflow condition from occurring.

FEATURES Size 10" MATERIALS Body

Covers Springs Seats C.V. Discs Fasteners Test Cock Handles

Epoxy Coated (FDA Approved) Ductile Iron Epoxy Coated (FDA) Ductile Iron Stainless Steel Bronze EPDM Stainless Steel Stainless Steel

Contact local water authorities for installation/service requirements.

Flow Curves :

• • • • • • • •

Patents #6,343,618 and #5,711,341 Reversible/Replaceable seat discs Corrosion resistant Economical Low head loss Short lay length Designed for easy maintenance Approved for vertical and horizontal installations • Gate valves epoxy coated (FDA)

ORDERING CODE Y-STRAINER 0-Standard 1-w/ Y-strainer (shipped loose)

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

• • • • • • • • •

Check valve assemblies interchangeable Maximum working pressure 175 psig Operating temperature range 33°F-140°F USC FCCCHR AWWA C-510 ASSE 1015 UL Classified FM approved Designed, manufactured, assembled and tested in South Carolina, USA

4S - 1 X X - 0 X X SIZE G - 10"

FLOW (OPTIONAL) VALVES N - N-Flow 1 -less gate valves 2 -w/ NRS gate valves 3 -w/ OS&Y gate valves 5 -w/ Epoxy coated ball valves 6 -w/ OS&Y gate valve on inlet, universal post indicator plate and operating nut on outlet 7-w/Flanged inlet x Grooved outlet (OS&Y) 8 -w/Grooved x Grooved OS&Y gate valves 10 - OS&Y Flg x Grv Post Indicator

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. DC4S10 Ordering No. 4S-10G Body Size 10" (250) A 55-3/4 (1416) B 29-1/2 (750) C NRS 26-1/2 (673) C (OS&Y) OPEN 46 (1168) D 19-1/2 (495) E 16 (406) F 51-3/4 (1314) G 39-1/2 (1003) H (Post Indicator) 26.5 (673) Test Cocks 3/4 NPT (20) Net Wt. (Less Gate Valves) 470 (213) Net Wt. (With NRS Valves) 1175 (533) Net Wt. (With OS&Y Valves) 1320 (599) Net Wt. (With NRS Valves & Elbows) 1548 (702) Net Wt. (With OS&Y Valves & Elbows) 1693 (768) Net Wt. (With Ball Valves) N/A N/A Net Wt. (With Post Indicator) 1280 (580) Shpg. Wt. (Less Gate Valves) 565 (256) Shpg. Wt. (With NRS Valves) 1265 (574) Shpg. Wt. (With OS&Y Valves) 1638 (743) Shpg. Wt. (With NRS Valves & Elbows) 1420 (644) Shpg. Wt. (With OS&Y Valves & Elbows) 1793 (813) Shpg. Wt. (With Ball Valves) N/A N/A Shpg. Wt. (With Post Indicator) 1390 (630)

10"

*Nominal dimensions are shown. Allowances must be made for manufacturers’ tolerances.

8

Customer Service 1-704-841-6000

Double Check Detector Backflow Preventers

DCDA-4SG Series DCDA-4SG SERIES DOUBLE CHECK DETECTOR ASSEMBLY The Apollo® DCDA-4SG Series Double Check Detector Assembly is designed to prevent contamination of the potable water supply due to back-siphonage or backpressure from substances that are non-health hazards. The device consists of a mainline double check valve with resilient seated shut-off valves. The by-pass serves to measure water use of up to 3 gpm. Grooved connections on an epoxy-coated ductile iron body allow for easy connection to butterfly valves or gate valves.

FEATURES

Sizes 2-1/2”, 3", 4", 6", 8" MATERIALS Body (mainline) Bypass DC Covers (2-1/2” - 6”) Covers (8”) Check Valves (2-1/2” - 6”) Check Valves (8”) Springs Seat Discs Test Cock Handles

Epoxy-coated (FDA) Ductile Iron Bronze Epoxy-coated (FDA) Steel Epoxy-coated (FDA) Ductile Iron Glass-Filled Noryl® Bronze Stainless Steel Chloramine-Resistant EPDM Stainless Steel

• • • • • • •

Lightweight Short lay length Low pressure loss Modular check valves Individual access to check valves Reversible/replaceable seat discs Approved for vertical and horizontal installations • Gate valves epoxy coated (FDA)

ORDERING CODE -

4SG - 6 0 X - X [X] - X

SIZE METER OPTION 9 - 2-1/2” C - Cubic feet/min 0 - 3” E - Gallons/min A - 4” G - Less meter C - 6” E - 8” Example: 4SG-60A-E7 = 4” size with meter in gpm and OS&Y flanged x grooved shut-off valves

• Corrosion resistant epoxy-coated ductile iron body • UL Classified • FM approved • USC FCCCHR • ASSE 1048 • CSA • US Patents #5,711,341 and #6,343,618 • MADE IN THE USA

FLOW (OPTIONAL) SHUT-OFF VALVES (Inlet x Outlet) N - N- Flow 1 - Less Shut-off Valves (grooved-end body) 2 - NRS Flg x NRS Flg 3 - OS&Y Flg x OS&Y Flg 4 - OS&Y Flg x Monitored Butterfly Valve Grv 6 - OS&Y Flg x Flg Post Indicator** 7 - OS&Y Flg x OS&Y Grv 8 - OS&Y Grv x OS&Y Grv 9 - Mon. Butterfly Vlv Grv x Mon. Butterfly Vlv Grv 10 - OS&Y Flg x Grv Post Indicator**

**Post indicator with plate & nut option not available in 2-1/2” size

Dimensions - in(mm) - Weights - lbs.(kg) Model No. DCDA4SG212 DCDA4SG3 Ordering No. 4SG-609 4SG-600 3"(80) Size 2 1/2"(65) 29 1/2 (749) A (Butterfly Valves)* 29 (737) A (Gate Valves)* 32 (813) 33 (838) 17 (432) B (Grooved End Body) 17 (432) C (Butterfly Valves) 8 (200) 8 1/2 (216) C (OS&Y Open) 16 3/8 (416) 18 7/8 (479) 4 1/2 (114) D (Butterfly Valves) 4 1/2 (114) D (Gate Valves) 3 1/2 (89) 3 3/4 (95) 9 (229) E 9 (229) H (Post Indicator Valve) 14.75 (375) 14.80 (376) Test Cocks (NPT) 1/2 1/2 Net Wt. (Less Valves) 65 (29) 65 (29) Net Wt. (w/Butterfly Valves) 92 (42) 95 (42) Net Wt. (w/OS&Y Valves) 161 (73) 186 (84)

DCDA4SG4 4SG-60A 4"(100) 29 3/4 (756) 34 1/2 (876) 16 1/2 (419) 9 1/4 (235) 22 3/4 (578) 4 1/2 (114) 4 1/2 (114) 9 (229) 14.80 (376) 1/2 65 (29) 109 (49) 220 (100)

DCDA4SG6 4SG-60C 6"(150) 32 (813) 39 (991) 18 (457) 10 1/4 (260) 30 1/8 (765) 4 1/2 (114) 5 1/2 (140) 9 (229) 18.75 (476) 3/4 72 (33) 140 (64) 321 (146)

DCDA4SG8 4SG-60E 8”(200) 43 (1092) 50 (1270) 27 (686) 12 (300) 37 3/4 (959) 6 1/2 (165) 6 3/4 (171) 10 3/4 (273) 24.42 (595) 3/4 395 (179) 526 (239) 872 (397)

*Nominal dimensions are shown. Allowances must be made for manufacturers’ tolerances.

9 www.apollovalves.com

Double Check Detector Backflow Preventers

DCDA-4S SERIES (Previously Model DCDA) DOUBLE CHECK DETECTOR ASSEMBLY The Apollo Model DCDA-4S Double Check Detector Assembly is designed to provide double check protection against cross-connection of non-potable (non-hazardous) water into the safe drinking water system; and at the same time offers precise monitoring capability to detect leakage or unauthorized use of water from fire or automatic sprinkler systems. The unit consists of two independently acting, spring loaded check valves with inlet and outlet resilient wedge gate valves and a by-pass assembly consisting of a water meter, double check valve assembly with shut-off valves and test cocks.

OPERATION

Size 10"

During normal conditions, if the downstream pressure of the assembly increases above the supply pressure or there is a reverse direction of flow; the line and by-pass double check valves will close to prevent backflow. If the second check valve of either the line or by-pass is prevented from closing tightly, the first check valves will still provide protection from a backflow condition. The line and by-pass double check valves will remain closed during the no flow condition. If there is a low flow demand (up to a minimum of 3 gpm) of water downstream, which may be caused by a system leak or unauthorized use, the flow is routed through the water meter to monitor such consumption. Higher flow will cause the main line double check valve to open while water continues to flow at the by-pass at a rate below capacity.

FEATURES

MATERIALS Body and covers

FDA Approved epoxy coated ductile iron (mainline) Bronze (by-pass) By-pass components Bronze Springs Stainless Steel (both) Seats Bronze (both) Discs EPDM (both) Fasteners Stainless Steel Test cocks Bronze (both) Test cock handles Stainless Steel

• • • • • • • • • •

US Patent #6,343,618 Corrosion Resistant Reversible/Replaceable Seat Discs Low Head Loss Economical Short Lay Length Designed For Easy Maintenance Horizontal and vertical installation approvals Check Valve Assemblies Interchangeable Gate valves epoxy coated (FDA)

ORDERING CODE -

Contact local water authorities for installation/service requirements.

SIZE G – 10"

Flow Curves :

• • • • • • • •

4S - 6 0 G - X X X

METER C — With meter in cubic feet E — With meter in gallons G — Less water meter

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

Maximum Working Pressure 175 PSI Operating Temperature Range 33˚F-140˚F UL Classified FM Approved USC FCCCHR ASSE 1048 CSA Designed, manufactured, assembled and tested in South Carolina, USA

FLOW (OPTIONAL) GATE VALVES N – N-Flow 1 — Less gate valves 3 — With OS&Y gate valves 6 — w/OS&Y gate valve on inlet, w/post indicator valve w/ plate and nut on outlet 7 — W/ Flanged inlet x Grooved outlet (OS&Y) 8 — w/Grooved x Grooved OS&Y gate valves

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. DCDA4S10 Ordering No. 4S-60G Size 10" (250) A 55-3/4 (1416) B 29-1/2 (750) C (NRS) 26-1/2 (673) C (OS&Y OPEN) 46 (1168) D 16 (406) E 10-3/4 (273) F 51-3/4 (1314) G 39-1/2 (1003) H 11-1/2 (292) Test Cocks (Mainline) 3/4 NPT (20) Test Cocks (Bypass) 1/4 NPT (6) Net. Wt. (Less Gate Valves) 490 (222) Net. Wt. (w/OS&Y Valves) 1340 (607) Net. Wt. (w/Elbows & OS&Y Valves) 1714 (777) Net. Wt. (w/Post Indicator) 1277 (579) Shpg. Wt. (Less Gate Valves) 585 (265) Shpg. Wt. (w/OS&Y Valves) 1440 (653) Shpg. Wt. (w/Elbows & OS&Y Valves) 1814 (823) Shpg. Wt. (w/Post Indicator) 1377 (625) *Nominal dimensions are shown. Allowances must be made for manufacturers’ tolerances.

10

Customer Service 1-704-841-6000

Reduced Pressure Backflow Preventers

RP-4A Series REDUCED PRESSURE PRINCIPLE The Apollo Series RP-4A Reduced Pressure Principle Backflow Preventer is designed to give maximum protection against backflow caused by either back-pressure or back-siphonage from substances that are hazardous. The durable but economical device is easily maintained in the line with modular check cartridge assemblies that require no special tools. It consists of two independently acting spring-loaded check valves with an automatic differential relief valve located between the check valves. The diaphragm and the sensing passage are built into the all bronze body to eliminate possible damage. All testcocks are mounted at the top of the unit to assure easy access during repair and maintenance when unit is installed in tight places.

FEATURES Sizes 1/2", 3/4", 1", 1-1/4", 1-1/2", 2"

MATERIALS Body and Covers Springs Seat Discs Diaphragm Check Modules O-rings Ball Valve Handles

Cast Bronze C84400 300 Series SS Chloramine-resistant Silicone Nitrile and Nylon Glass-Filled PPO Chloramine-resistant EPDM Stainless Steel

Contact local water authorities for installation/service requirements.

• Maximum protection against back-pressure/back-siphonage • Modular check valve cartridges w/easily replaced parts • Reversible/removable chloramineresistant silicone seat discs • Low head pressure loss • Top mounted test cocks • Internal sensing passage

ORDERING CODE -

• Comes standard with Apollo® full port ball valves with stainless steel handles • Economical • Corrosion resistant • Maximum working pressure 175 psig • Operating temperature range 33°F-180°F • ASSE 1013 for horizontal installation on 3/4” and 1” • Designed, manufactured, assembled and tested in South Carolina, USA

4A - 2 X X - T X X

Y-STRAINER SIZE 0-Standard 3-1/2" 1-w/ Y-strainer (shipped loose) 4-3/4" 5-1" 6-1-1/4" 7-1-1/2" 8-2"

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks L - lever handle (3/4” & 1” only) LL-locking lever handles

SHUT-OFF VALVES 1-less ball valves 2-w/ball valves (Standard) 4-w/union ball valves

Example: 4A-215-T4LL = 1” Reduced Pressure Backflow Preventer with strainer, union ball valves and locking lever handles

Flow Curves : Pressure loss vs. flow data as determined by independent approval agencies.

E C F

B A See page 38 for air gap drain information.

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RP4A12 RP4A34 Ordering No. 4A-203-T 4A-204-T 3/4" (20) Body Size 1/2" (15) A 10-3/4 (273) 12-1/2 (318) B 7-3/8 (187) 8-1/2 (216) C 7 (178) 9-1/2 (184) D 2-3/4 (70) 7-7/8 (80) E 3-1/8 (81) 3-1/4 (86) F 3-7/8 (98) 3-7/8 (98) Net Wt. 7.2 (3.3) 8.8 (4.0)

RP4A1 4A-205-T 1" (25) 15-1/4 (387) 9-1/2 (241) 7-7/8 (200) 3-1/4 (83) 3-7/8 (98) 4 (100) 12.6 (5.7)

www.apollovalves.com

RP4A114 4A-206-T 1-1/4" (32) 18 (457) 11-3/4 (298) 9-3/4 (248) 4-3/4 (121) 4-3/8 (111) 5-3/8 (137) 18.5 (8.4)

RP4A112 4A-207-T 1-1/2" (40) 18-5/8 (473) 11-5/8 (295) 9-3/4 (248) 5-1/4 (133) 4-3/8 (111) 5-3/8 (137) 21.5 (9.8)

RP4A2 4A-208-T 2" (50) 21-1/2 (546) 12-3/4 (324) 10-7/8 (276) 5-7/8 (149) 4-7/8 (124) 6 (150) 33.4 (15.1)

11

Reduced Pressure Backflow Preventers

RP-40 Series REDUCED PRESSURE PRINCIPLE The Apollo Series RP-40 Reduced Pressure Principle Backflow Preventer is designed to give maximum protection against backflow caused by either back-pressure or back-siphonage. The durable, but economical, device is easily maintained in the line without any special tools. It consists of two independently acting spring-loaded check poppet valves with an automatic differential relief valve located between the check valves. The diaphragm and the sensing passage are built into the all bronze body to eliminate possible damage. Three of the testcocks are mounted at the top to assure easy access during repair and maintenance when unit is installed in tight places. (#2 testcock mounted on relief valve cover for tight installations.)

Sizes 1/4", 3/8", 1/2", 3/4", 1", 1-1/4", 1-1/2", 2"

FEATURES

MATERIALS Body and covers Springs Poppets Seat Discs Diaphragm R.V. Stem Fasteners Replaceable Seats Ball Valve Handles

Bronze Stainless Steel Glass-Filled Celcon® Silicone Rubber Nitrile and Nylon Noryl® Stainless Steel Glass-Filled Noryl® Stainless Steel

• Maximum protection against back-pressure/back-siphonage • Reversible/Removable silicone seat discs • Internal sensing passage • Designed for easy maintenance • Low head loss • Economical • Corrosion resistant • Replaceable seat rings • Comes standard with Apollo® full port ball valves with stainless steel handles

ORDERING CODE -

Maximum working pressure 175 psig Operating temperature range 33°F-180°F Replaceable seats UL Classified (less shut-offs) USC FCCCHR AWWA 511 ASSE 1013 Designed, manufactured, assembled and tested in South Carolina, USA

40 - 2 X X - T X X

Contact local water authorities for installation/service requirements.

Flow Curves :

• • • • • • • •

Y-STRAINER SIZE 0-Standard 1-1/4" 1-w/ Y-strainer (shipped loose) 2-3/8" 3-1/2" 4-3/4" (*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards. 5-1" 6-1-1/4" 7-1-1/2" 8-2"

SHUT-OFF VALVES 1-less ball valves (UL Classified) 2-w/ball valves (Standard) 4-w/union ball valves

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks L - lever handle (3/4” & 1” only) LL-locking lever handles

Example: 40-215-T4LL = 1” Reduced Pressure Backflow Preventer with strainer, union ball valves and locking lever handles

See page 38 for air gap drain information.

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RP4014 RP4038 Ordering No. 40-201-T 40-202-T 3/8" (10) Body Size 1/4" (6) A 10-3/16 (259) 10-1/4 (260) 5-3/4 (146) B (w/o Ball Valves) 5-3/4 (146) C 6-7/8 (175) 6-7/8 (175) D 2-5/8 (67) 2-5/8 (67) 3-1/8 (79) E 3-1/8 (79) F 3-3/4 (95) 3-3/4 (95) Test Cocks Net Wt. (w/o Ball Valves) Net Wt. (w/ Ball Valves) Shpg. Wt. (w/o Ball Valves) Shpg. Wt. (w/ Ball Valves)

12

1/8x1/4NPT

5.7 7 6.6 7.9

(2.6) (3.2) (3.0) (3.6)

1/8x1/4NPT

5.7 7 6.6 7.9

(2.6) (3.2) (3.0) (3.6)

RP4012 40-203-T 1/2" (15) 10-3/4 (273) 5-3/4 (146) 6-7/8 (175) 2-5/8 (67) 3-1/8 (79) 3-3/4 (95)

RP4034 40-204-T 3/4" (20) 13-3/4 (349) 8 (200) 9-3/4 (248) 4-1/16 (103) 4-1/2 (115) 5-1/8 (130)

RP401 40-205-T 1" (25) 15-3/8 (390) 8 (200) 9-3/4 (248) 4-1/16 (103) 4-1/2 (115) 5-1/8 (130)

1/8x1/4NPT

1/8x1/4NPT

1/8x1/4NPT

(2.3) (3.4) (2.7) (3.8)

11-1/2 (5.2) 14 (6.4) 12.5 (5.7) 15 (6.8)

5.1 7.4 6 8.3

Customer Service 1-704-841-6000

11 14.5 12 15.5

(5.0) (6.7) (5.4) (7.0)

RP40114 40-206-T 1-1/4" (32) 17-1/2 (445) 11 (280) 12-5/8 (320) 5-3/8 (137) 5-11/16 (145) 7-1/8 (180)

RP40112 40-207-T 1-1/2" (40) 19-1/2 (495) 11 (280) 12-5/8 (320) 5-3/8 (137) 5-11/16 (145) 7-1/8 (180)

RP402 40-208-T 2" (50) 21-1/2 (546) 11 (280) 12-5/8 (320) 5-3/8 (137) 5-11/16 (145) 7-1/8 (180)

1/4x1/4NPT

1/4x1/4NPT

1/4x1/4NPT

30.5 35.5 32.5 38

(13.8) (16.1) (14.7) (17.2)

27.5 37 29 39

(12.5) (16.8) (13.2) (17.7)

27 39-1/2 29 41

(12.2) (17.9) (13.2) (18.6)

Reduced Pressure Backflow Preventers

RP-40 Series

N AND Z FLOW REDUCED PRESSURE PRINCIPLE The Apollo Series RP-40 Reduced Pressure Principle Backflow Preventer is designed to give maximum protection against backflow caused by either back-pressure or back-siphonage. The durable, but economical, device is easily maintained in the line without any special tools. It consists of two independently acting spring-loaded poppet check valves with an automatic differential relief valve located between the check valves. The diaphragm and the sensing passage are built into the all bronze body to eliminate possible damage. The assembly offers installation flexibility by providing inlet and outlet bronze elbows to meet space requirements, adaptability and lower installation cost. The No. 3 and No. 4 test cocks are mounted at the top to assure easy access during repair and maintenance when unit is installed in tight places.

Z-Flow Shown with option (F) SAE threaded test cocks

OPERATION During normal flow conditions, the two check valves are held off their seats, supplying water downstream. The relief valve is held shut by supply pressure acting through the internal sensing passage, on the relief valve diaphragm. In the area between the check valves, called the zone, the pressure is maintained at approximately 7 psi lower than supply pressure. Should a back-pressure or backsiphonage condition occur, the second check valve will seal, prohibiting the backflow of water. Should the second check valve become fouled, the pressure in the zone will increase causing the differential relief valve to open to atmosphere. This will maintain the pressure in the zone at least 2 psi lower than supply pressure.

N-Flow Sizes 3/4", 1", 1-1/4", 1-1/2", 2" MATERIALS Body, covers & elbows Springs Poppets Seat Discs Diaphragm R.V. Stem Fasteners Replaceable Seats Ball Valve Handles

Bronze Stainless Steel Glass-Filled Celcon® Silicone Rubber Nitrile and Nylon Noryl® Stainless Steel Glass-Filled Noryl® Stainless Steel

FEATURES • Maximum protection against back-pressure/back-siphonage • Flexibility in installation • Low installation cost • Compact • Internal sensing passage • Low head loss • Reversible/Removable seat discs • Replaceable seat rings

ORDERING CODE -

Contact local water authorities for installation/service requirements.

Flow Curves :

SIZES 4-3/4" 5-1" 6-1-1/4" 7-1-1/2" 8-2"

• Comes standard with Apollo® full port ball valves with stainless steel handles • Maximum working pressure 175 psig • Temperature range 33°F-180°F • UL Classified (less shut-offs) • USC FCCCHR • AWWA 511 • ASSE 1013 • CSA • Designed, manufactured, assembled and tested in South Carolina, USA

40 - 2 0 X - T X X X

SHUT-OFF VALVES 1-less ball valves (UL Classified) 2-w/ball valves (Standard) 4-w/union ball valves

FLOW N - N-Flow Z - Z-Flow

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks L-Lever handles (34” & 1”) LL-locking lever handles

Example: 40-204-T4ULL = 3/4” Reduced Pressure Backflow Preventer with union ball valves, with U-flow, and locking lever handles See page 38 for air gap drain information.

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

Dimensions -in.(mm) – Weights - lbs.(kg) Model No. RP40x34 Ordering No. 40-204-T Body Size 3/4" (20) A 10-1/2 (267) B 8 (200) C 4-1/8 (105) D 4-7/16 (113) E 13-7/8 (352) F 4-7/16 (113) G 5-1/8 (130) Test Cocks 1/8 x 1/4NPT Net Wt. (with Ball Valves) 14.7 (6.7) Shpg. Wt. (with Ball Valves) 15.7 (7.1)

RP40x1 40-205-T 1" (25) 10-11/16 (271) 8 (200) 5-3/16 (132) 4-9/16 (116) 15-1/8 (333) 4-7/16 (113) 5-1/8 (130) 1/8 x 1/4NPT 15.6 (7.1) 16.6 (7.5)

www.apollovalves.com

RP40x114 40-206-T 1-1/4" (32) 14-3/16 (360) 11 (279) 6 (150) 5-3/4 (146) 19 (483) 5-11/16 (145) 7-1/8 (196) 1/4 x 1/4NPT 37.5 (17.0) 40 (18.1)

RP40x112 40-207-T 1-1/2" (40) 15-1/8 (384) 11 (279) 6-5/8 (168) 5-7/8 (149) 20-3/4 (527) 5-11/16 (145) 7-1/8 (196) 1/4 x 1/4NPT 39.37 (17.9) 41.37 (18.8)

RP40x2 40-208-T 2" (50) 15-3/4 (381) 11 (279) 7-5/8 (194) 6-1/4 (159) 22-1/8 (562) 5-11/16 (145) 7-1/8 (196) 1/4 x 1/4NPT 43.8 (19.9) 45.3 (20.5)

x = N or Z Flow

13

Reduced Pressure Backflow Preventers

RP-40 Series REDUCED PRESSURE PRINCIPLE The Apollo Series 40-RP Reduced Pressure Backflow Preventer consists of two independently acting, spring-loaded center stem guided check valves with a differential pressure relief valve located between the check valves. The all bronze relief valve module is easily removed from the ductile iron check valve body. Pressure sensing passages are built into the bronze relief valve module to prevent possible damage from mishandling or vandalism. The unit is available with inlet and outlet shutoff valves. Four test cocks, three on the backflow preventer valve body and one on the inlet shutoff valve, complete the assembly.

OPERATION

Sizes 2-1/2", 3", 4"

FEATURES

MATERIALS Body and covers

Springs Seats C.V. Discs R.V. Disc R.V. Diaphragm R.V. Body Fasteners Test Cock Handles

Epoxy Coated (FDA Approved) Ductile Iron Stainless Steel Bronze EPDM Silicone Nitrile and Nylon Bronze Stainless Steel Stainless Steel

Contact local water authorities for installation/service requirements.

Flow Curves :

During normal flow conditions, the two check valves are held off their seats, supplying water downstream. The relief valve is held shut by supply pressure acting through the internal sensing passage, on the relief valve diaphragm. In the area between the check valves, called the zone, the pressure is maintained at approximately 7 psi lower than supply pressure. Should a back-pressure or back-siphonage condition occur, the second check valve will seal, prohibiting the backflow of water. Should the second check valve become fouled, the pressure in the zone will increase causing the differential relief valve to open to atmosphere. This will maintain the pressure in the zone at least 2 psi lower than supply pressure.

• Maximum protection against backpressure/back-siphonage • Reversible/Removable seat discs • Replaceable bronze seats • Internal sensing passage • Designed for easy maintenance • Low head loss • Economical • Corrosion resistant • Maximum working pressure 175 psig • Gate valves epoxy coated (FDA)

ORDERING CODE -

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

• Horizontal installation approvals • Operating temperature range 33°F 140°F • UL Classified • FM approved • USC FCCCHR • ASSE 1013 • CSA • AWWA 511 • Designed, manufactured, assembled and tested in South Carolina, USA

40 - 2 X X - 0 X

Y-STRAINER 0-Standard 1-w/ epoxy Y-strainer (shipped loose)

SIZE 9-2-1/2" 0-3" A-4"

*Post indicator w/ plate & nut option not available in 2-1/2” size.

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RP40212 Ordering No. 40-209 Body Size 2-1/2" (65) A 37-1/16 (941) B 22-1/16 (560) C NRS 20-7/8 (530) C OS&Y (OPEN) 25-7/8 (657) D NRS 11-3/8 (289) D OS&Y (OPEN) 16-3/8 (416) E 9-1/2 (241) F 9-5/8 (244) G 7 (178) Test Cocks 1/2 x 1/2 NPT Net Wt. (Less Gate Valves) 120 (54) Net Wt. (With NRS Valves) 219 (99) Net Wt. (With OS&Y Valves) 229 (104) Net Wt. (With Ball Valves) 188 (85) Shpg. Wt. (Less gate Valves) 184 (83) Shpg. Wt. (With NRS Valves) 283 (128) Shpg. Wt. (With OS&Y Valves) 293 (133) Shpg. Wt. (With Ball Valves) 252 (114)

14

Customer Service 1-704-841-6000

VALVES 1-less gate valves 2-w/ NRS gate valves 3-w/OS&Y gate valves 5-w/Epoxy coated ball valves 6-OS&Y flg x flg post indicator* 7-OS&Y flg x OS&Y grv 8-OS&Y grv x OS&Y grv 10-OS&Y flg x grv post indicator*

RP403 40-200 3" (80) 38-1/16 (967) 22-1/16 (560) 21-7/8 (556) 28-3/8 (721) 12-3/8 (314) 18-7/8 (479) 9-1/2 (241) 10-3/8 (264) 7-1/2 (191) 1/2 x 1/2 NPT 122 (55) 252 (114) 259 (117) 198 (90) 186 (84) 316 (143) 323 (147) 262 (119)

RP404 40-20A 4" (100) 46-3/4 (1187) 28-1/2 (724) 25-3/16 (640) 33-3/16 (843) 14-3/4 (375) 22-3/4 (578) 10-7/16 (265) 11-7/8 (302) 9 (229) 1/2 x 1/2 NPT 196 (89) 388 (176) 402 (182) 312 (142) 260 (118) 452 (205) 466 (211) 376 (171)

RP-40 Series

Reduced Pressure Backflow Preventers

REDUCED PRESSURE PRINCIPLE The Apollo Series RP-40 Reduced Pressure Backflow Preventer consists of two independently acting, spring-loaded center stem guided check valves with a differential pressure relief valve located between the check valves. The relief valve module is easily removed from the ductile iron check valve body. Pressure sensing passages are built into the relief valve module to prevent possible damage from mishandling or vandalism. The unit is available with inlet and outlet shutoff valves. Four test cocks, three on the backflow preventer valve body and one on the inlet shutoff valve, complete the assembly.

OPERATION Sizes 6", 8", 10" MATERIALS Body and covers

Springs Seats C.V. Discs R.V. Disc R.V. Diaphragm R.V. Body R.V. Body

Fasteners Test Cock Handles

Epoxy Coated (FDA Approved) Ductile Iron Stainless Steel Bronze EPDM Silicone Nitrile and Nylon Bronze – For 6" only Epoxy Coated (FDA Approved) Ductile Iron – For 8" and 10" only Stainless Steel Stainless Steel

Contact local water authorities for installation/service requirements.

Flow Curves :

During normal flow conditions, the two check valves are held off their seats, supplying water downstream. The relief valve is held shut by supply pressure acting through the internal sensing passage, on the relief valve diaphragm. In the area between the check valves, called the zone, the pressure is maintained at approximately 7 psi lower than supply pressure. Should a back-pressure or back-siphonage condition occur, the second check valve will seal, prohibiting the backflow of water. Should the second check valve become fouled, the pressure in the zone will increase causing the differential relief valve to open to atmosphere. This will maintain the pressure in the zone at least 2 psi lower than supply pressure.

FEATURES • Maximum protection against backpressure/back-siphonage • Removable bronze seats • Reversible/Replaceable seat discs • Internal sensing passage • Designed for easy maintenance • Low head loss • Economical • Corrosion resistant • Gate valves epoxy coated (FDA)

ORDERING CODE -

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RP406 Ordering No. 40-20C Body Size 6" (150) A 63 (1600) B 42 (1067) C NRS 30-1/2 (775) C OS&Y (OPEN) 41-5/8 (1057) D NRS 19 (483) D OS&Y (OPEN) 30-1/8 (765) E 11-1/2 (292) F 14-5/8 (371) G 11 (279) Test Cocks 3/4 x 3/4 NPT Net Wt. (Less Gate Valves) 430 (195) Net Wt. (With NRS Valves) 736 (334) Net Wt. (With OS&Y Valves) 754 (342) Net Wt. (With Ball Valves) 666 (302) Shpg. Wt. (Less gate Valves) 528 (239) Shpg. Wt. (With NRS Valves) 872 (396) Shpg. Wt. (With OS&Y Valves) 890 (404) Shpg. Wt. (With Ball Valves) 836 (379)

RP408 40-20E 8" (200) 75 (1905) 52 (1448) 38-1/2 (978) 53-3/4 (1365) 22-1/2 (572) 37-3/4 (959) 16 (406) 16-3/4 (425) 13-1/2 (343) 3/4 x 3/4 NPT 715 (324) 1155 (524) 1210 (549) N/A N/A 885 (401) 1335 (606) 1390 (630) N/A N/A

www.apollovalves.com

• • • • • • • • • •

Horizontal installation approvals Maximum working pressure 175 psig Operating temperature range 33°F-140°F UL Classified FM approved USC FCCCHR ASSE 1013 CSA AWWA 511 Designed, manufactured, assembled and tested in South Carolina, USA

40 - 2 X X - 0 X

Y-STRAINER SIZE 0-Standard C-6" 1-w/ epoxy Y-strainer (shipped loose) E-8" G-10"

RP4010 40-20G 10" (250) 88-1/4 (2242) 62-1/16 (1576) 44 (1118) 63-1/4 (1607) 26-1/2 (673) 45-34 (1162) 17-1/2 (445) 19-1/4 (489) 16 (406) 3/4 x 3/4 NPT 1443 (655) 2148 (974) 2286 (1037) N/A N/A 1613 (732) 2364 (1072) 2502 (1135) N/A N/A

VALVES 1-less gate valves 2-w/ NRS gate valves 3-w/OS&Y gate valves 5-w/Epoxy coated ball valves 6-OS&Y flg x flg post indicator 7-OS&Y flg x OS&Y grv 8-OS&Y grv x OS&Y grv 10-OS&Y flg x grv post indicator

See page 38 for air gap drain information.

15

Reduced Pressure Backflow Preventers

RP-40 Series FIRE HYDRANT BACKFLOW METER The Apollo Series RP-40 Fire Hydrant Backflow Meter shall measure potable water flow from a fire hydrant or other non-permanent installation. At the same time it shall protect against backflow by either back-pressure or back-siphonage from a cross-connection between potable water system and substances that are non-health and health hazards. The unit shall consist of a 3/4" Short Water Meter, 1" 40-205 RP device, 1" resilient-seated full port ball valve with locking device, 2 1/2"-7 1/2" NST threaded hose couplings, strainer on inlet of meter and adjustable support rod assembly.

OPERATION

Size 1" Contact local water authorities for installation/service requirements.

The Fire Hydrant Backflow Meter is connected directly to a fire hydrant with a 2 1/2"-7 1/2" NST fire hose female swivel coupling. The device operates like a standard Reduced Pressure device except the flow through the device is measured by a Water Meter connected to the inlet of the backflow preventer. Support rod assembly is adjustable to accommodate fire hydrants at different heights from the ground.

FEATURES • • • • • • •

Normal operating flow range 2-30 gpm Accuracy 100% ± 1.5% of actual thruput Low flow registration 95% at 1/2 gpm Maximum pressure loss 11.0 psi at 30 gpm Maximum operating pressure 150 psi Measuring element oscillating piston Register is straight reading, hermetically sealed magnetic drive • Meter maincase is bronze, measuring chamber is Rocksyn, a corrosion resistant thermoplastic material, maincase bottom plate is bronze, gears are self-lubricating, molded plastic for long life and minimum friction, magnets are Alnico, trim and casing bolts are stainless steel and strainer is thermoplastic.

• Tamperproof locking system inside the meter • 2 1/2"-7 1/2" NST fire hose swivel couplings, female inlet, male outlet • Maximum rate listed is for intermittent flow only. Maximum continuous flow rate as specified by AWWA is 15 gpm. • Designed, manufactured, assembled and tested in South Carolina, USA

DIMENSIONS (in.)—WEIGHTS (lbs.) NET WEIGHT 24.1 SHIPPING WEIGHT 27.6

See page 38 for air gap drain information.

Model Number 40-205-FHB 40-205-FHBG

16

(meter in cu. ft.) (meter in gallons)

Customer Service 1-704-841-6000

Reduced Pressure Backflow Preventers

RP-40S Series STAINLESS STEEL REDUCED PRESSURE PRINCIPLE BACKFLOW PREVENTER The Apollo Series RP-40S Stainless Steel Reduced Pressure Principle Backflow Preventer is designed to give maximum protection against backflow caused by either backpressure or backsiphonage from a cross-connection wherein a contaminant hazard exists (i.e. a health hazard), or a pollutant hazard exists (i.e. a non-hazard). The assembly is composed of two spring-loaded poppet type check valves and a mechanically independent, hydraulically dependent pressure differential relief valve set in an integral stainless steel body. Three of the testcocks are mounted at the top to assure easy access during repair and maintenance when unit is installed in tight places.

OPERATION

Sizes 1/4", 3/8", 1/2", 3/4", 1" MATERIALS Body and Cover Springs Fasteners Poppets Seat Discs Diaphragm and O-Rings Replaceable Seats Test Cocks & Handles

Stainless Steel Stainless Steel Stainless Steel Glass-Filled Celcon® Silicone Rubber FDA Fluorocarbon Glass-Filled Noryl® Stainless Steel

Contact local water authorities for installation/service requirements.

During normal flow conditions, the two check valves are held off their seats, supplying water downstream. The relief valve is held shut by supply pressure acting through the internal sensing passage, on the relief valve diaphragm. In the area between the check valves, called the zone, the pressure is maintained at approximately 7 psi lower than supply pressure. Should a back-pressure or back-siphonage condition occur, the second check valve will seal, prohibiting the backflow of water. Should the second check valve become fouled, the pressure in the zone will increase causing the differential relief valve to open to atmosphere. This will maintain the pressure in the zone at least 2 psi lower than supply pressure.

FEATURES • • • • • • •

Stainless steel body and covers Easy to install and repair Internal sensing passage Low head loss Reversible/Removable seat discs Replaceable seats Comes standard with Apollo® stainless steel full port ball valves with stainless steel handles

• • • • • •

Maximum working pressure 175 psig Temperature range 33°F-180°F USC FCCCHR ASSE 1013 CSA Designed, manufactured, assembled and tested in South Carolina, USA

ORDERING CODE - 40 - 2 X X - T X S X

Flow Curves : (*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

SIZE 1-1/4" 2-3/8" 3-1/2" 4-3/4" 5-1"

Y-STRAINER 0-Standard 1-w/ SS Y-strainer (shipped loose)

SHUT-OFF VALVES 1-less ball valves (UL classified-3/4”,1”) 2-w/SS ball valves (Standard)

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks LL-locking lever handles

See page 38 for air gap drain information.

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RP40S14 RP40S38 Ordering No. 40-201-TxS 40-202-TxS Body Size 1/4" (6) 3/8" (10) A 10-1/2 (267) 10-1/2 (267) B 5-3/4 (146) 5-3/4 (146) 6-7/8 (175) C 6-7/8 (175) D 2-5/8 (68) 2-5/8 (68) E 3-3/16 (81) 3-3/16 (81) F 3-3/4 (95) 3-3/4 (95) Test Cocks 1/8 x 1/4NPT 1/8 x 1/4NPT 4.3 (2.0) Net Wt. (w/o Ball Valves) 4.3 (2.0) Net Wt. (with Ball Valves) 5.5 (2.5) 5.5 (2.5) Shpg. Wt. (w/o Ball Valves) 5.2 (2.4) 5.1 (2.3) Shpg. Wt. (with Ball Valves) 6.4 (2.9) 6.4 (2.9)

RP40S12 40-203-TxS 1/2" (12) 10-1/2 (267) 5-3/4 (146) 6-7/8 (175) 2-5/8 (68) 3-3/16 (81) 3-3/4 (95) 1/8 x 1/4NPT 4.1 (1.9) 5.4 (2.4) 5 (2.3) 6.3 (2.8)

www.apollovalves.com

RP40S34 40-204-TxS 3/4" (20) 13-1/2 (343) 7-15/16 (202) 9 (229) 4-1/16 (103) 4-3/8 (111) 5-1/8 (130) 1/8 x 1/4NPT 8.1 (3.8) 10.8 (4.9) 9.8 (4.4) 12.3 (5.6)

RP40S1 40-205-TxS 1" (25) 15-1/4 (387) 7-15/16 (202) 9 (229) 4-1/16 (103) 4-3/8 (111) 5-1/8 (130) 1/8 x 1/4NPT 8.1 (3.7) 11 (5.0) 9.6 (4.3) 12.8 (5.8)

x=Shut-off valve configuration

17

Reduced Pressure Backflow Preventers

®

RP-4D Series DEFENDER

RP-4D SERIES REDUCED PRESSURE PRINCIPLE ASSEMBLY The Apollo Valves RP-4D Reduced Pressure Backflow Preventer Defender™ provides maximum backflow protection in a lead free, short lay length, compact package. The assembly consists of two independently acting, spring loaded, poppet type check valves with a differential pressure relief valve located in the zone between the checks. The all stainless steel check valve modules are easily removed from the ductile iron body via a large access cover. The stainless steel relief valve module is also accessible and removable. The Defender™ is available with monitored butterfly valves. Ninety-degree elbows are also available within the shut-off valve envelope for compact installations. 2-1/2” - 10”

OPERATION

Shown w/ Standard Butterfly Shutoffs

MATERIALS Body and cover Test Cocks & Handles Check Components Relief Valve Springs Seat Discs Fasteners Elbows

Fusion Bonded Epoxy Coated Ductile Iron Stainless Steel Stainless Steel Stainless Steel (Noryl™ Seat on 2.5”-6” Stainless Steel Silicone Rubber Stainless Steel Fusion Bonded Epoxy Coated Ductile Iron

Contact local water authorities for installation/service requirements.

During normal flow conditions, the two poppet style check valves are held off their seats, supplying water downstream. The relief valve is held shut by supply pressure acting through the sensing tube. Should a back-pressure or back-siphonage condition occur, the second check will seal, prohibiting the backflow of water. Should the second check become fouled, the pressure in the zone will increase causing the differential relief valve to open to atmosphere, discharging the contents of the zone.

FEATURES • Low Pressure Loss Characteristics (without high curve spikes) • 316 Stainless Steel Checks Provide Superior Durability • Reversible/Replaceable Silicone Rubber Seat Discs • Monitored Butterfly Shut-Off Valves Standard • Short Lay Length • Maximum working pressure 175 PSI

ORDERING CODE -

PRESSURE LOSS (PSI)

SIZE 9 -2-1/2” 0 - 3” A - 4” C - 6” E - 8” G -10”

• • • • • • •

Operating temperature range 33°F-140°F UL Classified FM approved ASSE 1013 AWWA 511 CSA US Patent #6,443,184 B1 (other patents pending) • Designed, manufactured, assembled and tested in South Carolina, USA

4D - 2 0 X - 0 X X GATE VALVES FLOW (OPTIONAL) 1* - Less Shut-off Valves N - with two 9 - With Grooved x Grooved Butterfly elbows (can valves (Supervisory switch) be field adjusted up or down) *4D Defender valve body has grooved x grooved connections

FLOW RATE (GPM)

Model No. Ordering No. Size A (Butterfly Valves) B C (With Butterfly Valves) D E1 (center to coupling edge) F (w/Elbows & Butterfly Valves) G H “U” Flow (with Butterfly Valves) I “Z” Flow (with Butterfly Valves) Test Cocks Net Wt. (Less Gate Valves) Net Wt. (w/Butterfly Valves) Net Wt. (w/Elbows & B-fly Vlvs) Shpg. Wt. (Less Gate Valves) Shpg. Wt. (w/Butterfly Valves) Shpg. Wt. (w/Elbows & Butterfly Vlvs)

Dimensions - in(mm) - Weights - lbs.(kg) RP4D212 RP4D3 RP4D4 RP4D6 4D-208 4D-200 4D-20A 4D-20C 2 1/2"(65) 3"(80) 4"(100) 6"(150) 33 3/8 (848) 33 7/8 (860) 35 (889) 38 1/2 (978) 21 3/8 (543) 21 3/8 (543) 21 3/8 (543) 24 1/2 (622) 10 5/8 (270) 10 5/8 (270) 13 (330) 10 5/8 (270) 10 3/4 (273) 10 3/4 (273) 10 3/4 (273) 11 3/4 (298) 6 1/2 (165) 6 1/2 (165) 6 1/2 (165) 7 3/4 (197) 8 (200) 8 1/2 (216) 9 1/4 (235) 10 1/4 (260) 22 (559) 23 (584) 25 (635) 29 (737) 21 1/8 (537) 22 3/8 (568) 26 1/2 (673) 20 3/8 (518) 19 1/2 (498) 21 (533) 23 1/4 (591) 27 (686) 1/2 NPT 109 (49) 132 (60) 141 (64) 173 (78) 199 (90) 208 (94)

See page 38 for air gap drain information.

18

Customer Service 1-704-841-6000

1/2 NPT 110 (50) 134 (61) 146 (66) 174 (79) 201 (91) 213 (97)

1/2 NPT 115 (52) 154 (70) 174 (79) 179 (81) 221 (100) 241 (109)

3/4 198 261 298 296 369 406

NPT (90) (118) (135) (134) (167) (185)

RP4D8 4D-20E 8”(200) 48 (1219) 32 (813) 15 (381) 15 1/4 (387) 10 (254) 12 3/4 (324) 46 (1168) 29 3/4 (756) 30 (762) 3/4 417 539 581 493 615 681

NPT (189) (244) (264) (224) (279) (309)

RP4D10 4D-20G 10”(250) 52 1/2 (1334) 32 (813) 15 (381) 15 1/4 (387) 10 (254) 14 1/2 (368) 50 1/4 (1276) 34 (864) 38 (965) 3/4 422 604 712 498 680 812

NPT (191) (274) (323) (226) (308) (368)

Reduced Pressure Backflow Preventers

RPDA-40 Series REDUCED PRESSURE DETECTOR ASSEMBLY The Apollo Series RPDA-40 Reduced Pressure Detector Assembly is designed to provide reduced pressure principle protection against cross-connections that present a health hazard, and at the same time detect leakage or unauthorized use of water from fire or automatic sprinkler systems. The mainline unit consists of two independent spring-loaded, poppet type check valve assemblies with a diaphragm actuated and spring-loaded, relief valve assembly located between check valves. Two resilient wedge gate valves and four test cocks complete the mainline unit. The by-pass consists of an approved reduced pressure assembly, four test cocks, two shut-off valves and a water meter.

OPERATION Sizes 3", 4" MATERIALS Body and covers

FDA Approved epoxycoated ductile iron (mainline), By-pass (bronze) By-pass components Bronze Springs Stainless Steel (both) Seats Bronze (both) C.V. discs EPDM (mainline) Silicone rubber (by-pass) R.V. discs Silicone rubber (mainline) EPDM (by-pass) Diaphragm Nitrile and nylon (both) R.V. body Bronze (mainline) Fasteners Stainless Steel (both) Test cock handles Stainless Steel

Contact local water authorities for installation/service requirements.

During no flow conditions, the mainline and by-pass check valves will remain closed. Also, both mainline and by-pass relief valves stay closed due to the pressure differential between supply and zone pressure. If there is a low flow demand (up to a minimum of 3 gpm) of water downstream, which may be caused by a system leak or unauthorized use, the flow is routed through the water meter to monitor such consumption. Higher flow will tend to open the mainline check valves at which point water continues to flow at the by-pass at a rate below capacity. In the event pressure increases downstream, tending to reverse direction of flow, both check valves in the mainline and by-pass are closed to prevent backflow. If the second check valve in either the mainline or by-pass is prevented from closing tightly, leakage into the reduced pressure zone increases pressure and will cause the relief valves to open. If the supply pressure drops to atmosphere or lower than the reduced pressure zone, the relief valves will open creating an internal air gap in both assemblies. Contact local water authorities for installation/service requirements.

FEATURES • Maximum protection against back-pressure/back-siphonage • Removable bronze seats • Reversible/replaceable seat discs • Internal sensing passage • Corrosion resistant • Easy in-line maintenance and testing • Maximum working pressure 175 psig

40 - 7 0 X - X X

ORDERING CODE SIZE 0 — 3" A — 4"

Flow Curves :

• Horizontal installation approvals • Operating temperature range 33°F-140°F • UL Classified • FM approved • USC FCCCHR • ASSE1047 • CSA • Designed, manufactured, assembled and tested in South Carolina, USA

METER C — With meter in cubic feet E — With meter in gallons G — Less water meter

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

GATE VALVES 1 — Less gate valves 3 — With OS&Y gate valves 6 — w/OS&Y gate valve on inlet, NRS gate valve w/ post plate and nut on outlet 7 - With Flanged Inlet x Grooved Outlet (both OS&Y) 8 - With Grooved x Grooved OS&Y gate valves 10 - OS&Y Flg x Grv Post Indicator

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RPDA403 Ordering No. 40-700 Size 3"(80) A 38-1/16 (968) B 22-1/16 (562) C (OS&Y) OPEN 18-7/8 (479) D 3-3/4 (95) E (OS&Y) OPEN 28-3/8 (721) F 9-1/4 (235) G 3-3/4 (95) Test cocks (line) 1/2" NPT Test cocks (by-pass) 1/4" NPT Net Wt. (less gate valves) 145 (66) Net Wt. (with 0S&Y valves) 282 (128) Shipping Wt. (less gate valves) 209 (95) Shipping Wt. (with OS&Y valves) 346 (157)

RPDA404 40-70A 4"(100) 46-3/4 (1187) 28-1/2 (724) 22-3/4 (578) 4-1/2 (114) 33-3/16 (843) 10-1/2 (267) 4-1/2 (114) 1/2" NPT 1/4" NPT 217 (98) 423 (192) 281 (127) 487 (221)

See page 38 for air gap drain information. www.apollovalves.com

19

Reduced Pressure Backflow Preventers

RPDA-40 Series REDUCED PRESSURE DETECTOR ASSEMBLY The Apollo Series RPDA-40 Reduced Pressure Detector Assembly is designed to provide reduced pressure principle protection against cross-connections that present a health hazard, and at the same time detect leakage or unauthorized use of water from fire or automatic sprinkler systems. The mainline unit consists of two independent spring-loaded, poppet type check valve assemblies with a diaphragm actuated and spring-loaded assembly located between check valves. Two resilient wedge gate valves and four test cocks complete the mainline unit. The by-pass consists of an approved reduced pressure assembly, four test cocks, two shut-off valves and a water meter.

OPERATION

Sizes 6",8”, 10"

MATERIALS Body and covers

FDA Approved epoxycoated ductile iron (main line),By-pass (bronze) By-pass components Bronze Springs Stainless Steel (both) Seats Bronze (both) C.V. discs EPDM (mainline) Silicone rubber (by-pass) R.V. discs Silicone rubber (mainline) EPDM (by-pass) Diaphragm Nitrile and nylon (both) Mainline R.V. body Bronze (6" only) FDA Approved epoxycoated ductile iron (8" & 10") Fasteners Stainless Steel (both) Test cock handles Stainless Steel

During no flow conditions, the mainline and by-pass check valves will remain closed. Also, both mainline and by-pass relief valves stay closed due to the pressure differential between supply and zone pressure. If there is a low flow demand (up to a minimum of 3 gpm) of water downstream, which may be caused by a system leak or unauthorized use, the flow is routed through the water meter to monitor such consumption. Higher flow will cause the mainline check valves to open while water continues to flow at the by-pass at a rate below capacity. In the event pressure increases downstream, tending to reverse direction of flow, both check valves in the mainline and by-pass are closed to prevent backflow. If the second check valve in either the mainline or by-pass is prevented from closing tightly, leakage into the reduced pressure zone increases pressure and will cause the relief valves to open. If the supply pressure drops to atmosphere or lower than the reduced pressure zone, the relief valves will open creating an internal air gap in both assemblies.

FEATURES • Maximum protection against backpressure/back siphonage • Removable bronze seats • Reversible/replaceable seat discs • Internal sensing passage • Corrosion resistant • Easy in-line maintenance and testing • Maximum working pressure 175 psig

ORDERING CODE SIZE C — 6" E — 8" G — 10"

Contact local water authorities for installation/service requirements.

Flow Curves :

40 - 7 0 X - X X METER C — With meter in cubic feet E — With meter in gallons G — Less water meter

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

See page 38 for air gap drain information.

20

• Operating temperature range 33°F-140°F • UL Classified • FM approved • USC FCCCHR • ASSE 1040 • CSA • Designed, manufactured, assembled and tested in South Carolina, USA

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. RPDA406 Ordering No. 40-70C Size 6"(150) A 63 (1600) B 42 (1067) C (OS&Y) OPEN 30-1/8 (765) D 5-1/2 (140) E (OS&Y) OPEN 41-5/8 (1057) F 13-1/4 (337) G 5-1/2 (140) Test cocks (line) 3/4" NPT Test cocks (by-pass) 1/2" NPT Net Wt. (less gate valves) 452 (205) Net Wt. (with 0S&Y valves) 776 (352) Shipping Wt. (less gate valves) 550 (249) Shipping Wt. (with OS&Y valves) 912 (414)

Customer Service 1-704-841-6000

GATE VALVES 1 — Less gate valves 3 — With OS&Y gate valves 6 — w/OS&Y gate valve on inlet, NRS gate valve w/ post plate and nut on outlet 7 - With Flanged Inlet x Grooved Outlet (both OS&Y) 8 - With Grooved x Grooved OS&Y gate valves 10 - OS&Y Flg x Grv post indicator

RPDA408 40-70E 8"(200) 75 (1905) 52 (1321) 37-3/4 (959) 6-3/4 (171) 53-3/4 (1365) 14-3/4 (375) 6-3/4 (171) 3/4" NPT 1/4" NPT 738 (335) 1233 (559) 908 (412) 1413 (641)

RPDA4010 40-70G 10"(250) 88-1/4 (2242) 62-1/16 (1578) 45-3/4 (1152) 8 (200) 63-1/4 (1607) 17-1/2 (445) 8 (200) 3/4" NPT 1/4" NPT 1471 (667) 2314 (1050) 1641 (744) 2530 (1148)

Reduced Pressure Backflow Preventers

RPDA-4D Series DEFENDER® 4D SERIES REDUCED PRESSURE DETECTOR ASSEMBLY

2-1/2” - 10” Shown w/ Standard Butterfly Shutoffs

MATERIALS Body and cover Coated Test Cocks Check Components Relief Valve Springs Seat Discs Fasteners Elbows

Fusion Bonded Epoxy Ductile Iron (mainline) Bronze (by-pass) Stainless Steel (mainline) Bronze (by-pass) Stainless Steel (mainline) Acetal (by-pass) Stainless Steel (Noryl™ Seat on 2.5”-6”) Stainless Steel Silicone Rubber Stainless Steel Fusion Bonded Epoxy Coated Ductile Iron

Contact local water authorities for installation/service requirements.

The Apollo model RPDA-4D Series is designed to provide reduced pressure principle protection against cross-connections that present a health hazard; and at the same time offers precise monitoring capability to detect leakage or unauthorized use of water from the fire or automatic sprinkler system. The RPDA-4D Series is available in sizes 2-1/2” - 10”. The unit consists of a mainline 4D Series Reduced Pressure Principle assembly with two independently acting poppet type check valves with a diaphragm actuated and spring loaded relief valve assembly located between the checks. A bronze by-pass line by-passes the 2nd check. The by-pass line consists of a meter, a single check, shut-off isolation valves, and test cocks. The relief valve on the mainline device maintains high hazard protection, as the by-pass is downstream of the reduced pressure zone.

OPERATION During normal conditions, the mainline device provides normal reduced pressure backflow protection against back-siphonage or backpressure. If a backflow condition should occur the two mainline poppet style checks along with the by-pass single check will close tight. If there is a low flow demand (up to a minimum of 2 gpm) of water downstream, which may be caused by a system leak or unauthorized use, the flow is routed through the water meter to monitor such consumption. Higher flows will open the mainline checks as required.

FEATURES • Low pressure loss characteristics (without high curve spikes) • 4D Series Mainline Valve Provides Superior Durability • Low Maintenance By-Pass Line (no relief valve to maintain) • Reversible/Replaceable Silicone Rubber Seat Discs • Dependable Neoperl™ Check Module Utilized in Single Check • Monitored Butterfly Valves are Standard

ORDERING CODE SIZE METER 9 -2-1/2” C - With Meter in Cubic 0 -3” Feet A -4” E - With Meter in Gallons C -6” G - Less Meter E -8” G-10”

• • • • • • • •

Short Lay Length Maximum working pressure 175 PSI Operating temperature range 33°F-140°F UL Classified FM approved ASSE1047 CSA US Patent #6,443,184 B1 (other patents pending) • Easy Access for Maintenance • Designed, manufactured, assembled and tested in South Carolina, USA

4D - 7 0 X - X X X GATE VALVES FLOW (OPTIONAL) 1* - Less Shut-off Valves N - with two 9 - With Grooved x Grooved Butterfly elbows (can valves (Supervisory switch) be field adjusted up or down) *4D Defender valve body has grooved x grooved connections

See page 38 for air gap drain information.

Dimensions - in(mm) Model No. RPDA4D212 RPDA4D3 Ordering No. 4D-709 4D-700 Size 2 1/2"(65) 3"(80) 33 7/8 (860) A (Butterfly Valves) 33 3/8 (848) B 21 3/8 (543) 21 3/8 (543) C (With Butterfly Valves) 10 5/8 (270) 10 5/8 (270) D 10 3/4 (273) 10 3/4 (273) E1 (center to coupling edge) 6 1/2 (165) 6 1/2 (165) 11 (279) E2 (center to by-pass edge) 11 (279) F (w/Elbows & Butterfly Valves) 8 (203) 8 1/2 (216) G 27 3/8 (695) 28 1/8 (714) H “n” Flow (with Butterfly Valves) 20 3/8 (568) 21 1/8 (536) 19 1/2 (495) 21 (533) I “Z” Flow (with Butterfly Valves) Test Cocks 1/2 NPT 1/2 NPT Net Wt. (Less Gate Valves) 118 (54) 119 (55) Net Wt. (w/Butterfly Valves) 141 (64) 143 (65) 155 (70) Net Wt. (w/Elbows & Butterfly Vlvs) 150 (68) Shpg. Wt. (Less Gate Valves) 182 (83) 183 (83) Shpg. Wt. (w/Butterfly Valves) 208 (94) 210 (95) Shpg. Wt. (w/Elbows & Butter Vlvs) 217 (98) 222 (101) www.apollovalves.com

- Weights - lbs.(kg) RPDA4D4 RPDA4D6 4D-70A 4D-70C 4"(100) 6"(150) 35 (889) 38 1/2 (978) 21 3/8 (543) 24 1/2 (622) 10 5/8 (270) 13 (330) 10 3/4 (273) 11 3/4 (298) 6 1/2 (165) 7 3/4 (197) 11 (279) 11 (279) 9 1/4 (235) 10 1/4 (260) 29 3/4 (756) 35 1/2 (902) 22 3/8 (568) 26 1/2 (673) 23 1/4 (591) 27 (686) 1/2 NPT 3/4 NPT 124 (56) 207 (94) 163 (74) 270 (122) 183 (83) 307 (139) 188 (85) 305 (138) 230 (104) 378 (171) 250 (113) 415 (188)

RPDA4D8 4D-70E 8”(200) 48 (1219) 32 (813) 15 (381) 15 1/4 (387) 10 (254) 14 1/2 (368) 12 3/4 (233) 46 (1168) 29 3/4 (756) 30 (762) 3/4 NPT 429 (195) 551 (250) 593 (269) 505 (229) 627 (284) 693 (314)

RPDA4D10 4D-70G 10”(250) 52 1/2 (1334) 32 (813) 15 (381) 15 1/4 (387) 10 (254) 14 1/2 (368) 14 1/2 (368) 50 1/4 (1276) 34 (864) 38 (965) 3/4 NPT 434 (197) 616 (279) 724 (328) 510 (231) 692 (314) 824 (374)

21

Vacuum Breaker Backflow Preventers

AVB1 SERIES ATMOSPHERIC TYPE VACUUM BREAKERS The Apollo Series AVB1 Atmospheric Type Vacuum Breaker is designed to prevent back-siphonage of polluted water into a potable water system. It should only be installed in areas where spillage of water could not cause damage and where it can be accessible for periodic maintenance. This device is not designed for continuous pressure application. Should be installed a minimum of 6” above all downstream piping with no downstream shutoffs.

OPERATION

Sizes 1/4",3/8", 1/2", 3/4", 1", 1-1/4, 1-1/2", 2" MATERIALS Valve Body Seat Disc Float & Gasket Guide Seat Canopy Screw

Cast Bronze Silicone Polypropylene Brass Cast Bronze Chrome-plated Steel Zinc-plated Steel

During flow conditions, the flow of water lifts the float disc and seals the atmospheric vent at all rates of flow, preventing leakage. When a negative pressure is created at the supply line or when the water supply valve upstream of the device is closed, the float disc will fall, thus opening the atmospheric vent. This prevents back-siphonage and creation of vacuum at the discharge line.

FEATURES • Corrosion resistant • Bronze body • Suitable for hot or cold water service: (up to 212°F at 125 psig) for up to 1" (up to 180°F at 125 psig) for 1-1/4" thru 2"

Flow Curves :

• Heat resistant silicone seat disc • Rough brass or polished chrome finish • Easy to maintain • Compact and lightweight • Durable • ASSE1001

(*) Rated flow as determined by ASSE design performance standards.

Contact local water authorities for installation/service requirements.

Pressure Loss (PSI)

Rate of flow

SUFFIX NO. 01 03 04

FINISH Rough Brass Rough Chrome Polished Brass

Rate of flow

Dimensions in.(mm) – Weights - lbs.(kg) Ordering No. Model No. Size 38-101 AVB114 1/4 (6) 38-102 AVB138 3/8 (10) 38-103 AVB112 1/2 (15) 38-104 AVB134 3/4 (20) 38-105 AVB11 1 (25) 38-106 AVB1114 1-1/4 (32) 38-107 AVB1112 1-1/2 (40) 38-108 AVB12 2 (50)

22

A 29/32 (23) 29/32 (23) 1-3/32 (28) 1-5/16 (33) 1-3/4 (45) 2 (50) 2 (50) 2-1/8 (54)

B 2-3/8 (60) 2-3/8 (60) 2-1/2 (65) 3-1/16 (78) 4-1/16 (103) 4-3/8 (111) 4-3/8 (111) 4-1/2 (114)

Customer Service 1-704-841-6000

C 1-1/32 (26) 1-1/32 (26) 1-3/16 (30) 1-15/32 (37) 1-7/8 (48) 2 (50) 2 (50) 2-1/4 (57)

D 1-13/16 (46) 1-13/16 (46) 1-3/16 (30) 2-1/8 (54) 2-7/8 (73) 3-3/4 (95) 3-3/4 (95) 3-3/4 (95)

Wt/100 50.96 (23) 47.7 (22) 54.7 (25) 79.7 (36) 174 (79) 316 (143) 289 (131) 369 (167)

Vacuum Breaker Backflow Preventers

AVB2 SERIES ATMOSPHERIC TYPE VACUUM BREAKERS (FORGED BODY) The Apollo Series AVB2 Atmospheric Type Vacuum Breaker is designed to prevent back-siphonage of polluted water into a potable water system. The device should only be installed in areas where spillage of water could not cause damage. This device is not designed for continuous pressure applications. Should be installed a minimum of 6” above all downstream piping with no shut offs downstream.

OPERATION During flow conditions, the flow of water lifts the float and seals the atmospheric vent, preventing leakage. If a negative pressure is created at the supply line or when the water supply valve upstream of the device is closed, the float will fall. This action opens the atmospheric vent, and prevents back-siphonage in the discharge line.

FEATURES Sizes 1/4", 3/8, 1/2", 3/4"

MATERIALS Body Seat Disc Float Cap and guide Canopy Screw

• Corrosion resistant • Forged brass body • Suitable for hot or cold water service up to 212°F and 125 psi

Forged Brass Silicone Polypropylene Noryl® Chrome-Plated Steel Zinc-plated steel

Flow Curves :

• Rough brass, rough chrome or polished chrome finish • Easy to maintain • Compact and lightweight • ASSE1001

(*) Rated flow as determined by ASSE design performance standards.

Contact local water authorities for installation/service requirements.

SUFFIX NO. 01 03 06 N

FINISH Rough Brass Rough Chrome Polished Chrome N Shape

Dimensions - in.(mm) – Weights Ordering No. Model No. 38-201 AVB214 38-202 AVB238 38-203 AVB212 38-204 AVB234 38-231N DMVB14 38-232N DMVB38

- lbs.(kg) Size 1/4 (6) 3/8 (10) 1/2 (15) 3/4 (20) 1/4 (6) 3/8 (10)

38-230

A 1-3/32 1-3/32 1-9/32 1-15/32 3/4 7/8

www.apollovalves.com

(28) (28) (33) (37) (20) (22)

B 2-5/16 2-5/16 2-5/8 3 2-7/32 2-7/32

38-200

(59) (59) (67) (80) (56) (56)

C 1-1/32 (26) 1-1/32 (26) 1-9/32 (33) 1-15/32 (37) 1-7/16 (36) 1-3/4 (44)

D 21/32 (17) 21/32 (17) 1-7/8 (48) 2 (50) 21/32 (17) 21/32 (17)

Wt/100 50.6 (23) 47.7 (22) 54.7 (25) 63.1 (29) 26.2 (12) 31.2 (14)

23

Vacuum Breaker Backflow Preventers

PVB-4A SERIES 4A VACUUM BREAKER The Apollo Model PVB-4A Pressure Vacuum Breakers are designed to prevent contamination of potable water due to back-siphonage. An integral relief valve serves to reduce the possibility of damage due to intermittent freezing conditions. The modular check valve cartridge has a replaceable seat and a reversible silicone seat disc. Apollo ball valves with stainless steel handles and nuts are standard.

FEATURES • Modular cartridge check valve • Low pressure loss • Built-in freeze resistant relief valve • Compact yet easy to maintain • Apollo ball valves w/SS handles & nuts standard • Test cocks located for easy draining • Corrosion resistant

• No special tools required • Unique canopy detachment • Patent pending • ASSE 1020 (1/2” - 1”) • Easy maintenance • Maximium operating pressure 150 psi • Design pressure 300 psi • Temperature range 33°F - 140°F • MADE IN THE USA

Sizes 1/2", 3/4", 1", 1-1/4",1-1/2", 2"

MATERIALS Body Canopy Bonnet Check Valve Cartridge Springs Seat Discs

Cast Bronze C84400 UV Resistant ABS Glass-Filled PPO Glass-Filled PPO Stainless Steel Chloramine-resistant Silicone Glass-Filled Polypropylene Chloramine-Resistant EPDM Stainless Steel

Float O-rings Ball Valve Handles

Flow Curves : Pressure loss vs. flow data as determined by independent approval agencies.

Contact local water authorities for installation/service requirements.

A

C

B

24

Dimensions - in.(mm) Ordering No. Model No. 4A-503-02 PVB4A12 4A-504-02 PVB4A34 4A-505-02 PVB4A1 4A-506-02 PVB4A114 4A-507-02 PVB4A112 4A-508-02 PVB4A2

Customer Service 1-704-841-6000

Size 1/2” (1/2) 3/4” (20) 1” (25) 1-1/4”(32) 1-1/2”(40) 2” (50)

A 4-1/8 (105) 4-5/8 (117) 5-1/2 (140) 7-1/8 (180) 7-3/8 (185) 9 (230)

B 3-1/2 (89) 4 (100) 4-3/4 (120) 5-1/2 (140) 5-7/8 (150) 6-7/8 (175)

C 7 (178) 7-1/2 (190) 8-1/2 (215) 10 (250) 10-3/8 (265) 12 (300)

Wt. lbs (kg) 3.2 (1.5) 3.8 (1.7) 5.2 (2.4) 9.1 (4.1) 12.5 (5.7) 21.0 (9.5)

Pressure Vacuum Breaker Backflow Preventers

PVB-4V SERIES (Previously Model PVB) FREEZE RESISTANT PRESSURE VACUUM BREAKER The Apollo Series PVB-4V Pressure Vacuum Breaker is designed to prevent contamination of the potable water supply due to back-siphonage. The PVB is ideally suited for continuous pressure, outdoor applications such as irrigation equipment, livestock watering systems, swimming pools, etc. The device consists of a unique one piece cap/float assembly and independently acting check valve, all attractively packaged in a rugged yet compact bronze body. All components are made of corrosion resistant materials, guaranteeing years of reliable service.

FEATURES • Removable integral check valve • One piece cap/float assembly • Built-in freeze relief valve in cap/float assembly • Corrosion resistant construction • Comes standard with Apollo® full port ball valves with stainless steel handles

• Maximum working pressure 150 psig • Operating temperature range 33°F-180°F • USC FCCCHR • ASSE 1020 • CSA • Easy maintenance

Sizes 1/2", 3/4", 1", 1-1/4",1-1/2", 2"

ORDERING CODE -

MATERIALS Body Canopy Cap Check Valve Float Springs Test Cocks Ball Valve Handles

Bronze Powder Coated Steel Acetal Acetal Acetal Stainless Steel Brass Stainless Steel

SIZE 3-1/2" 4-3/4" 5-1" 6-1-1/4" 7-1-1/2" 8-2"

4V - 5 0 X - 0 X X SHUT-OFF VALVES 1-less ball valves 2-w/ ball valves (standard) 4-w/union ball valves

OPTIONS (CAN BE COMBINED) F-SAE threaded test cocks LL-locking lever handles

Contact local water authorities for installation/service requirements.

Flow Curves :

Dimensions - in(mm) - Weights - lbs.(kg) Model No. PVB4V12 Ordering No. 4V-503 Body Size 1/2” (15) A 3 (76) B (Less Ball Valves) 4-3/4 (120) C 6-3/8 (162) D 7-1/8 (180) E 4-5/8 (117) F (Less Ball Valves) 5-3/8 (137) Test Cocks 1/8 x 1/4 NPT Net Wt. (Less Ball Valves) 2.2 (1.0) Net Wt. (With Ball Valves) 3.4 (1.5) Shipping Wt. (Less Ball Valves) 3.2 (1.4) Shipping Wt. (With Ball Valves) 4.4 (2.0)

PVB4V34 4V-504 3/4” (20) 3 (76) 4-3/4 (120) 7-1/8 (180) 7-5/8 (194) 5-1/8 (130) 5-3/8 (137) 1/8 x 1/4 NPT 2.2 (1.0) 3.9 (1.8) 3.2 (1.4) 4.9 (2.2)

www.apollovalves.com

PVB4V1 4V-505 1”(25) 3 (76) 4-3/4 (120) 7-1/2 (190) 8-3/8 (212) 5-7/8 (150) 5-3/8 (137) 1/8 x 1/4 NPT 2.2 (1.0) 5.3 (2.4) 3 (1.3) 6.3 (2.9)

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

PVB4V114 4V-506 1-1/4” (32) 3-3/4 (95) 5-3/8 (137) 8-3/4 (222) 10-5/8 (270) 7-3/8 (187) 6-7/8 (175) 1/4 x 1/4 NPT 4.3 (2.0) 9.3 (4.2) 5.6 (2.5) 10.5 (4.8)

PVB4V112 4V-507 1-1/2” (40) 3-3/4 (95) 5-3/8 (137) 9-1/4 (235) 10-7/8 (275) 7-3/8 (187) 7-1/4 (185) 1/4 x 1/4 NPT 4.3 (2.0) 12.2 (5.5) 5.8 (2.6) 13.7 (6.2)

PVB4V2 4V-508 2” (50) 5-1/4 (133) 6-5/8 (168) 10-1/4 (260) 12-1/8 (308) 7-1/8 (180) 8-5/8 (220) 1/4 x 1/4 NPT 8.8 (4.0) 23.3 (10.6) 10.3 (4.7) 24.8 (11.2)

25

Spill Resistant Vacuum Breaker Backflow Preventers

SVB-4W Series SPILL RESISTANT VACUUM BREAKERS The Apollo Series SVB-4W Spill Resistant Vacuum Breaker is designed to prevent contamination of the potable water supply due to back-siphonage. The SVB is ideally suited for continuous pressure, indoor applications where water spillage is undesirable. The device has a straight through flow path for minimal head loss. All components are easily accessible for easy repair and maintenance. All components are made of corrosion resistant materials for years of reliable service. Should be installed 6” above all downstream piping.

OPERATION During normal flow conditions, the check valve remains open and the atmospheric vent seals in the bonnet assembly. As the line pressure falls to 1 psi, the spring loaded atmospheric vent opens and the check valve closes, breaking the vacuum and thereby preventing backsiphonage. Water is not allowed to spill at any time during operation.

Sizes 1/4", 3/8", 1/2" MATERIALS Body Springs Seat Discs Valve Canopy Float Fasteners Ball Valve Handles

®

FEATURES

Noryl Stainless Steel Silicone Rubber ABS Plastic Acetal Stainless Steel Stainless Steel

Contact local water authorities for installation/service requirements.

• Corrosion Resistant • In-Line Flow • Integral Shut-Off Valves w/Stainless Steel Handles and Nuts • Designed For Easy Maintenance

ORDERING CODE -

• • • • •

Low Head Loss Economical Maximum Working Pressure 150 PSIG Operating Temperature Range 33˚F-180˚F ASSE 1056

4W - 5 0 X - 0 2 SIZE 1 – 1/4" 2 – 3/8" 3 – 1/2"

Flow Curves :

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

Dimensions - in.(mm) – Weights - lbs.(kg) Model No. SVB4W14 SVB4W38 Ordering No. 4W-501-02 4W-502-02 Size 1/4" (6) 3/8" (10) Test Cock 1/4" Flare 1/4" Flare 1.16 (0.5) Net Wt. 1.16 (0.5) Shipping Wt. 1.26 (0.6) 1.26 (0.6)

26

Customer Service 1-704-841-6000

SVB4W12 4W-503-02 1/2" (15) 1/4" Flare 1.16 (0.5) 1.26 (0.6)

Dual Check w/ Atmospheric Port Backflow Preventers

DCAP Series DUAL CHECK WITH ATMOSPHERIC PORT BACKFLOW PREVENTER The Apollo DCAP Series Backflow Preventer is designed to protect residential and commercial water supply lines from back-siphonage or back-pressure of non-potable (non-hazardous) substances. It has an intermediate atmospheric vent to insure protection from backflow conditions. It consists of two independently acting and spring-loaded check valves in a corrosion resistant material.

OPERATION

Sizes 1/2", 3/4"

During normal flow operation, the vent valve is closed, and the two check valves are open allowing flow of water through the unit. Each check valve is designed to hold at least 1 psi in the direction of flow. When a back-siphonage condition occurs, both check valves close and the atmospheric vent opens to permit air to enter the intermediate zone. In the event of back-pressure and if the second check valve is prevented from closing tightly, leakage will be vented to the atmosphere through the vent port.

FEATURES MATERIALS Body Springs C.V. Seat Discs Seats Spring and Seat Retainer O-Rings Poppets

Bronze Stainless Steel EPDM Glass-Filled Noryl® Glass-Filled Noryl®

• Corrosion resistant • Low head loss • Independently acting check valves • Ease of repair and installation • Economical • Suitable for hot or cold water service

• Durable • Maximum working pressure 175 psig • ASSE 1012 • CSA • Operating temperature range 33°F-210°F

Nitrile/EPDM Glass-Filled Noryl®

Contact local water authorities for installation/service requirements.

ORDERING CODE UNION INLET CONNECTION A – FNPT H – Solder joint 2 – Female BSPP

40 - 4 X X - X X X

INLET AND OUTLET SIZE 3 – 1/2" 4 – 3/4"

Flow Curves :

UNION OUTLET CONNECTION A – FNPT B – MNPT F – Female BSPP H – Solder joint

OPTION C – Canadian (discharge port not threaded)

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

(• 1/2" = 10 GPM)

TYPICAL INSTALLATION

Dimensions (in.) – Weights (lbs.) Model No. DCAP12, DCAP34 Ordering No. 40-4x33xM, 40-4x44xM x=connection type Size 1/2", 3/4" A 5 B 2-15/16 C 2-5/8 Unit Weight 1.9 www.apollovalves.com

27

Dual Check Backflow Preventers

DUC-4N Series DUAL CHECK VALVE The Apollo DUC-4N Series Dual Check Valve Backflow Preventer is designed to prevent crossconnections of non-potable water (non-hazardous) into safe drinking water systems. It is a compact and economical device that consists of two independently-acting, spring-loaded check valves in a corrosion-resistant material.

OPERATION

MATERIALS Body Union Tailpiece Union Nut Check Modules Springs Seat Discs

Cast Bronze C84400 Brass Brass Glass-Filled Noryl® (3/8”-1/2”) Acetal (3/4”-1”) Stainless Steel Buna-N

Each of the two spring-loaded check valves is designed to open at 1 psi differential in the direction of flow. The check valves will remain tightly closed until there is a demand for water downstream. If the downstream pressure of the device increases above the supply pressure or there is a reverse direction of flow, the check valves will close to prevent backflow. If the second check valve is prevented from closing tightly, the first check will close to provide protection from a backflow condition.

FEATURES • • • • •

Low Head Loss Independently-acting Check Valves Compact and Lightweight Corrosion Resistant Replaceable Check Modules

• Available in Standard and Swivel Types • Maximum Working Pressure 175 psi • Operating Temperature Range 33°F180°F • ASSE1024 • CSA

Contact local water authorities for installation/service requirements.

4N - 3 X X - X X

ORDERING CODE UNION INLET CONNECTION A – FNPT B – MNPT C – Female Meter Thread E – Male Meter Thread S – Female Meter Swivel 2 – Female BSPP

1,2

INLET AND OUTLET SIZE 2 – 3/8" 3 – 1/2" 4 – 3/4" 5 - 1”

1,2

OUTLET CONNECTION A – FNPT B – MNPT C – Female Meter Thread E – Male Meter Thread F – Female BSPP

Notes: 1 2

For meter threads, order one size larger than meter size. Not all inlet and outlet combinations are available. Please contact Conbraco Customer Service for availability.

DIMENSIONS (IN.)-WEIGHTS (LBS.)

Dimensions (in.) – Weights (lbs.) Size A B Wt. 3/8” & 1/2” 3/4” 3/4” Meter 1” 1” Swivel

3.32 4.375 5.35 4.375 5.67

1.88 2 2 2 2

Contact Customer Service for model numbers.

Meter Thread Sizing 5/8” Meter 3/4” Meter 1” Meter

28

Customer Service 1-704-841-6000

3/4” 1” 1-1/4”

.70 1.40 1.65 1.40 1.65

Dual Check Backflow Preventers

DUC-4FP Series DUAL CHECK VALVE The Apollo DUC-4FP Series Dual Check Backflow Preventer for Residential Fire Sprinkler Systems prevents backflow by either backpressure or backsiphonage from a cross-connection between potable water lines and substances that are objectionable, but not health-hazards.

FEATURES • • • • •

Low Pressure Loss Corrosion Resistant Replaceable Check Modules Pressure drop at 30 gpm is less than 6 psi Complies with NFPA Standard 13D

• • • • • •

Maximum Supply Pressure 175 psi Temperature Range 33°F - 180°F ASSE 1024 UL Classified CSA B64.6 Made in the USA

MATERIALS Body Union Tailpiece Union Nut Check Modules Spacer O-Ring

Bronze Brass Brass Acetal/Nitrile/Stainless Steel Glass-Filled Noryl® EPDM

Contact local water authorities for installation/service requirements.

Flow Curves : **UL 1469 - Hydraulic Pressure Loss Test**

DUC4FP - X X X

ORDERING CODE 1

INLET CONNECTION F – FNPT FMR - Female Meter Thread

1

OUTLET CONNECTION F – FNPT M - MNPT MMR - Male Meter Thread

SIZE 1 – 1” 114 - 1-1/4”

Example: DUC4FP-FMRF1 = 1” Female Meter Thread Inlet x 1” Female Nationa Pipe Thread Outlet Notes: 1

Not all inlet and outlet combinations are available. Please contact Conbraco Customer Service for availability.

www.apollovalves.com

29

Dual Check Backflow Preventers

DUC-40 Series DUAL CHECK VALVE The Apollo Series DUC-40 Dual Check Valve prevents backflow by either backpressure or backsiphonage resulting from a cross-connection between potable water lines and substances that are objectionable, but not health-hazards.

FEATURES • • • • •

In-line repairable Low pressure loss Corrosion resistant Compact and lightweight Independently-acting check valves

• • • •

ASSE 1024 CSA B64.6 Available in standard and swivel types MADE IN THE USA

PERFORMANCE RATING

Sizes 1/2", 3/4", 1"

Maximum Operating Pressure 175 psi Temperature Range 33° F - 180° F

MATERIALS Body Caps Springs Seat Discs

APPROVALS

Bronze Brass Stainless Steel EPDM

®

®

ASSE 1024 and CSA B64.6

ORDERING CODE 1,2

INLET CONNECTION A – FNPT B – MNPT C – Female Meter Thread E – Male Meter Thread S – Female Meter Swivel 2 – Female BSPP

40 - 3 X X - X X X

INLET AND OUTLET SIZE 3 – 1/2" 4 – 3/4" 5 – 1"

2

OPTIONS (CAN BE COMBINED) TP-w/Test Ports Drilled, Tapped w/Plugs TC-w/3 1/8”x1/4” Test Cocks

Example: 40-3S5-4A = 3/4” female meter swivel inlet x 3/4” FNPT outlet.

Notes: 1

1,2

OUTLET CONNECTION A – FNPT B – MNPT C – Female Meter Thread E – Male Meter Thread F – Female BSPP

For meter threads, order one size larger than meter size. Not all inlet and outlet combinations are available. Please contact Conbraco Customer Service for availability.

* Standard body not drilled & tapped for testcocks.

Dimensions (in.) – Weights (lbs.) Model No. Ordering No. Size A B C Wt. Wt. (w/test cocks & ball valves)

30

Customer Service 1-704-841-6000

DUC4012 40-3x3-3x 1/2" 4-3/8 3-1/2 1-1/2 2 4

DUC4034 40-3x4-4x 3/4" 4-3/8 3-1/2 1-1/2 2 4.6

DUC401 40-3x5-5x 1" 4-3/8 3-1/2 1-1/2 2.1 6.4

x=connection type

Carbonated Beverage Backflow Preventers

CBBP SERIES CARBONATED BEVERAGE BACKFLOW PREVENTER The Apollo CBBP Series Carbonated Beverage Backflow Preventer (CBBP) is designed to prevent the contamination of the potable water supply due to backflow when installed on water distribution lines serving beverage dispensing equipment. The device consists of two independently acting check valves biased to a normally closed position. A normally open atmospheric port is located between the check valves. During backflow conditions, the port vents gases and/or liquids. Additionally, the CBBP is equipped with a 100 mesh integral strainer screen at the inlet. All wetted areas of the device are non-toxic, corrosion resistant, and approved for use with potable water. The CBBP is suitable for supply pressures to 150 psig and water temperatures from 33˚ to 130˚ F.

Sizes 1/4", 3/8"

OPERATION

MATERIALS

Under static (non-flowing) conditions, the check valves remain in the closed position. When a valve is opened downstream (i.e. a drink is delivered from the beverage dispensing unit), the check valves open and permit the flow of water. Under backflow conditions, the diaphragm seat on the first check lifts and permits flow through the atmospheric port located between the two check valves. The strainer insures debris does not enter the carbonator.

End cap Strainer

FEATURES

Acetal PVC/Stainless Steel O-ring Nitrile Downstream Nitrile/Stainless Check Valve Steel/Acetal Upstream Check EPDM/Stainless Valve Body Acetal

• Compact Design • Lowest head loss • Atmospheric vent provides indication of problems • Integral strainer for equipment protection

• • • • •

Available in SAE & NPT connections Repairable check assemblies Non-metallic body for corrosion resistance CSA Certified to ANSI/NSF-61 ASSE1022

Contact local water authorities for installation/service requirements.

CBBP14

MODEL NO. ORDERING CODE -

4C - 1 0 X - 0X INLET & OUTLET CONNECTION 01 – Flare 02 – MNPT (3/8” only)

SIZE 1 – 1/4" 2 – 3/8"

Flow Curves :

(*) Rated flow as determined by USC’s FCCC&HR and ASSE design performance standards.

DIMENSIONS (IN.)

CBBP Size 1/4” 3/8” 3/8”

www.apollovalves.com

Connection Sizing 7/16”-20 UNF 5/8”-18 UNF 3/8” NPT

SAE Flare SAE Flare Male NPT

Wt./Ea .19 .19 .19

31

Hose Connection Dual Check Backflow Preventers

HBV2 SERIES 3/4" HOSE CONNECTION VACUUM BREAKERS Apollo’s HBV Hose Connection Vacuum Breakers are designed to prevent cross-connection caused by back-siphonage. They consist of a single check valve with atmospheric vacuum breaker vent. They feature a break-away set-screw for tamper-proof protection. They are not suitable for continuous pressure applications.

OPERATION At no flow situations, the check disc seats against the diaphragm with the atmospheric vent open. This prevents back-siphonage or backflow of water. At flow conditions, the spring-loaded check disc opens, thus allowing flow of water through the device and at the same time the diaphragm seals the atmospheric vent.

INSTALLATION 3/4”

It should only be installed in areas where spillage of water could not cause damage. For permanent installation, screw device directly into faucet, firmly hand tighten and turn set-screw in until head breaks off.

FEATURES • Maximum Working Pressure 125 psig • Maximum Temperature 180°F.

Ordering No. 38-314-AS 38-314-CS

• ASSE1011 • CSA B64.2

Model No. HBV234 HBVC234

Finish Satin Brass Satin Chrome

Wt./Ea .17 .17

38-314 shipped in 12 pcs./box

HBVB SERIES 3/4" ANTI-FREEZE HOSE CONNECTION VACUUM BREAKERS The Apollo Series HBVB Anti-Freeze Hose Connection Vacuum Breaker is especially designed to prevent back-siphonage on wall and yard hydrants. It features a break-away set-screw for tamper-proof protection and manual drain for protection against freezing conditions. It is not suitable for continuous pressure applications.

OPERATION The principle of operation is similar to the HCVB Series except it has a manual draining feature. To drain, slide water release ring to uppermost position. For use in non-freezing temperatures, slide ring to lowermost position.

INSTALLATION It should only be installed in areas where spillage of water could not cause damage. For permanent installation, screw device directly into faucet, firmly hand tighten and turn set-screw in until head breaks off.

FEATURES • Maximum Working Pressure 125 psig • Maximum Temperature 180°F.

• ASSE1011

3/4”

Ordering No. 38-404-AS

32

Customer Service 1-704-841-6000

Model No. HBVAF34

Finish Satin Brass

Wt./Ea .37

Hose Connection Vacuum Breaker/ Lab Faucet Dual Check Backflow Preventers

HBDUC SERIES 38-304-02

3/4" HOSE CONNECTION DUAL CHECK The Apollo Series HBDUC is designed to provide an in-line testable hose connection that will prevent backflow due to back-siphonage or low head back-pressure. Each device consists of two independent checks, forced loaded in the closed position with an atmospheric vent between the checks. The device is threaded for hose connection at both the inlet and outlet with a break-away set screw on the inlet for tamper proof installations. These devices are not suitable for continuous pressure applications.

OPERATION During initial pressurization, the inlet check shuttles forward to close the atmospheric vent. As flow is established, both the inlet and outlet check open to allow flow through the device. If a backflow condition is present, then both checks will close and the atmospheric vent opens to introduce air and break the siphon.

Size 3/4" MATERIALS

FEATURES

Body Brass Seats EPDM Check components Stainless steel Check guide Acetal

• Corrosion resistant body and checks • Low Head loss • Easy to install with break-away set screw

• Protects against back siphonage and low-head back pressure • ASSE1052 Flow Curves :

Contact local water authorities for installation/service requirements.

Ordering No. 38-304-02

Model No. HBDUC34

Wt./100 46

LFDUC Series LABORATORY FAUCET DUAL CHECK BACKFLOW PREVENTER The Apollo Series LFDUC is designed to provide protection against back-siphonage wherever a hose is connected to a faucet. The device consists of two independently acting checks with an intermediate relief port or vent. It is suitable for supply pressure up to 150 psig and a temperature range of 33°F-180°F. Not suitable for constant pressure conditions.

OPERATION

Sizes 1/4", 3/8"

During normal flow conditions, the two checks are held off their seats, supplying water downstream. The vent is held shut by supply pressure acting on the diaphragm. If the supply pressure should fall below atmospheric, the second check will close due to internal spring pressure and the vent will open to introduce air into the supply line and break the siphon. NOTE: This device should only be installed where spillage of water could not cause water damage.

FEATURES • Corrosion resistant • Forged brass body • Suitable for hot or cold water service up to 212°F and 125 psi

• • • •

Polished (-CP2 and -CP3 are rough brass only) Easy to maintain Compact and lightweight ASSE1035

Flow Curves :

Ordering No. 38-502-01 38-502-02 38-502-03 38-502-CP2** 38-502-CP3**

Model No. LFDUCMF38 LFDUCFF38 LFDUCFM38 LFDUCFF14 LFDUCFF38

Inlet 3/8" MNPSM* 3/8" FNPT 3/8'' FNPT 1/4" FNPT 3/8" FNPT

Outlet 3/8" FNPT 3/8" FNPT 3/8'' MNPSM 1/4" FNPT 3/8" FNPT

A(in.) 2.33 2.34 2.33 2.34 2.34

B(in.) 1.24 1.24 1.24 1.24 1.24

Wt./Ea .50 .50 .50 .50 .50

*American National Standard straight pipe thread for free-fitting mechanical joints (male) **-CP2 and -CP3 are non-approved devices with a rough brass finish for continuous pressure applications

www.apollovalves.com

33

Freeze Protection Valve Backflow Preventers

FPV Series FREEZE PROTECTION VALVE The Apollo Series FPV Freeze Protection Valve protects backflow preventers from freezing when installed in accordance with manufacturer’s instructions. All internal parts of the Freeze Protection Valve are replaceable.

OPERATION During flow conditions, the Freeze Protection Valve shall be drip-tight during above-freezing normal operating conditions. The Freeze Protection Valve shall be suitable for normal operating pressures of 20 to 175 psig.

FEATURES

MATERIALS Body Cap Spring Guide Spring Cap O-Ring Guide O-Ring Thermal Element

Bronze Brass Brass Stainless Steel Buna-N Buna-N Copper/Stainless Steel/EPDM

Contact local water authorities for installation/service requirements.

• • • • •

Installs easily on all backflow preventers Ease of repair with available repair kit 175 psig maximum operating pressure Corrosion resistant 1/4" male pipe thread inlet port

• • • • •

Mechanical operating principle Nominal start to open temperature of 35°F Maximum temperature of 180°F Compact design Patented design

•

Available with 1/8" male x 1/4" female Apollo® test cock

• •

IAPMO listed US patent #6,374,849

•

Discharge port accommodates 5/8" I.D. hose

ORDERING CODE -

MODEL NUMBERS Model 40-000-FPV1 Model 40-000-FPV2 – w/test cock

DIMENSIONS (in.) — Weights (lbs.)

34

NET WEIGHT EACH

(LB)

Model 40-000-FPV1 Model 40-000-FPV2

.70 .77

40 - 0 0 0 - F P V X OPTIONS 1 – w/1/8" NPT plug 2 – w/1/8" male x 1/4" female Apollo test cock R – Repair kit* for FPV1 and FPV2 * Repair kit includes: Thermal element, spring, spring guide, two O-rings (all internal parts)

“Y” Strainers Backflow Preventers

YB Strainer Series Y STRAINER FEATURES

A

• Maximum protection capability against foreign particles in piping systems and process equipment. • Cast bronze (81-3-7-9) body • 304 Stainless Steel screen • Sizes 1/8" thru 1/2" comes standard with 50 mesh (0.009" wire) • Sizes 3/4" thru 2" comes standard with 20

B

mesh (0.016" wire) • Other screen sizes available (contact customer service) • Operating pressure to 400 psig WOG • Removable self-aligning screen

Dimensions - in.(mm) – Weights - lbs.(kg) Ordering No.

Model No.

59-001-01 59-002-01 59-003-01 59-004-01 59-005-01 59-006-01 59-007-01 59-008-01

YB14 YB38 YB12 YB34 YB1 YB114 YB112 YB2

A

B

Cap Tapping Suffix-02

2 (50) 2-11/16 (68) 2-11/16 (68) 3-7/8 (98) 4-3/4 (121) 5-1/8 (130) 5-3/4 (146) 6-3/4 (171)

1-1/4 (32) 2 (50) 2 (50) 3-1/4 (83) 4 (100) 4-1/4 (108) 5 (127) 6 (150)

1/8 NPT 1/4 NPT 1/4 NPT 1/2 NPT 3/4 NPT 3/4 NPT 1 NPT 1-1/4 NPT

Size 1/4 NPT 3/8 NPT 1/2 NPT 3/4 NPT 1 NPT 1-1/4 NPT 1-1/2 NPT 2 NPT

Wt./Ea .42 (.19) .79 (.36) .75 (.34) 1.85 (.84) 2.76(1.25) 3.58(1.62) 5.41(2.45) 7.47(3.39)

YSCF SERIES FLANGED, STYLE 125YF, CLASS 125 WYE STRAINERS FEATURES • Iron strainers are complete with Flat Face flanges in accordance with ASME B16.1. • Strainer body meets applicable ASME Standard. • One piece cast body. • Strainers equipped with bolted cover flange that utilize a flat gasket seal. • Low pressure drop. • Upper and lower machined seats. • 304 SS perforated screens are standard. • Drain/Blow-off connection furnished with plug as standard.

• 2-1/2” thru 3” come standard with .045 perforated screens • 4” thru 10” come standard with .125 perforated screens • Other screen sizes available (contact customer service) • Generous screen area and properly proportioned straining chamber to minimize initial pressure drop while maximizing time between cleanings. • Compact end to end dimension. • Epoxy coated and lined option (add “E” Suffix)

Dimensions - in.(mm) – Weights - lbs.(kg) Ordering No.

Size

A

125YF25P045 125YF03P045 125YF04P125 125YF06P125 125YF08P125 125YF10P125

2-1/2" 3” 4” 6” 8” 10”

2.50 (65) 3.00 (80) 4.00 (100) 6.00 (150) 8.00 (200) 10.00 (250)

B 10.75 11.50 13.88 18.50 21.38 26.00

(273) (292) (353) (470) (543) (660)

C

D

E

Weight

8.00 (200) 8.75 (222) 9.50 (241) 12.63 (321) 16.38 (416) 19.00 (483)

11.25 (286) 12.25 (311) 13.38 (340) 17.69 (449) 23.00 (584) 26.70 (678)

1 1 1-1/4 1-1/2 1-1/2 2

35 (16) 43 (20) 75 (34) 154 (70) 243 (110) 390 (177)

NOTE: Add “E” to part number suffix for Epoxy option.

www.apollovalves.com

35

Accessories Backflow Preventers

EXV Series THERMAL EXPANSION RELIEF VALVES The Apollo EXV Thermal Expansion Relief Valves are designed primarily to relieve excessive water pressure build-up caused by thermal expansion. In a closed hot water piping system, as water is heated, thermal expansion occurs. The increase of pressure will exert unwarranted stress on the system components, which may reach harmful levels well before the emergency setting of the main relief valve is reached. By installing the Series EXV, it will control any amount of expanded water without causing pressure increase to exceed maximum setting.

FEATURES • Prevents excessive pressure build-up • Protects plumbing fixtures • Extends water heater life • Compact and lightweight design

• Economical • Easy to install and requires no special tool • Corrosion resistant

TYPICAL INSTALLATION

78 - X X X- R V

ORDERING CODE -

PRESSURE SETTING RELIEF VALVE CONNECTION

SIZE

3 4 5 6

- 3/4" - 3/4" - 1" - 1"

Dimensions (in.) Ordering No. 78-300 78-400 78-500 78-600

SWT THD SWT THD

0 1 2

- 125 psig - 100 psig - 80 psi

– Weights (lbs.) Model No. A EXVS34 2.6 EXVT34 2.5 EXVS1 3.1 EXVT1 3.2

4 5 6 7

B 3.9 2.7 4.5 3.5

C 3.2 3.4 3.7 3.9

-

Hose Barb Pex Comp. Fitting 1/2" NPT/SWT Fitting

Wt/Ea 1.5 1.1 2.05 2.15

36 Customer Service 1-704-841-6000

Relief valve shown rotated 90°. Valve should be assembled w/hose barb pointed out of page.

Accessories Backflow Preventers

Accessories TEST KITS The Apollo Backflow Preventer Test Kits are compact, lightweight and portable testing devices. They come equipped with a gauge, hoses (with integral filters) and all required adapter fittings. Also included is a flexible or adjustable strap for hanging the gauge, laminated test procedures and a molded plastic carrying case with foam inserts.

DIFFERENTIAL PRESSURE GAUGE TEST KITS

TK3 These are three-valve test kits used for testing all DCV, RPZ, PVB & SVB backflow preventers. • Differential pressure type with a dual scale of 0-15 psid/0-100kPa differential pressure range with a +2% accuracy (full scale).

TK5 This is a five-valve test kit used for testing all DCV, RPZ, PVB & SVB backflow preventers. The five valve test kit is similar to the three valve kit except it has two additional valves that make it possible to bleed lines without disconnecting hoses. Dimensions (in.) – Weights (lbs.) Ordering No. Model No. Application 40-200-TKU TK3 ALL DCV, RPZ, PVB & SVB 40-200-TK5U TK5 ALL DCV, RPZ, PVB & SVB

Wt./Ea. (lbs.) 6.5 6.5

TKF SERIES TEST KIT FITTING Brass fitting which installs onto Backflow Preventer Test Cocks by hand. No tools required. No Teflon® tape to deal with. Provides quicker testing. Sets of three fittings with o-rings for 1/4” SAE connections to the test kits. Packaged in a reclosable plastic bag.

Size 1/4” SAE x 1/4” NPT 1/4” SAE x 1/2” NPT 1/4” SAE x 3/4” NPT

Ordering No. 40-000-TFK 40-001-TFK 40-002-TFK

Model No. TFK14 TFK12 TFK34

Backflow Application 1/4” - 2” 2-1/2” - 6” 8” - 12”

HCPG Series 3/4" HOSE CONNECTION PRESSURE GAUGE The Apollo Hose Connection Pressure Gauge is designed to measure water pressure through a 3/4" hose thread connection. It consists of an indicator needle to determine maximum pressure. Ordering No. - W807800 Model No. - HCPG

FEATURES • 2-1/2" face dial • 0 - 300 psig pressure range • Swivel type 3/4" hose connection

• Adjustable indicator needle • Temperature range = 50°F - 130°F • Wt./100 46.0

ST1 Series ST1 SERIES SIGHT TUBE Used in USC testing procedures. The kit allows for visual inspection during testing, provides an extension to the check valve body and offers quick connection with the 90˚ elbow. Provides means to static test double check backflow preventers.

Ordering No. - 40-200-ST Model No. - ST1 www.apollovalves.com

37

Accessories Backflow Preventers

Accessories AIR GAP DRAIN

Model RP-40 & RP-4D Backflow Preventers

For installation with Conbraco’s RP-40 and RP-4D Series Reduced Pressure Principle backflow preventers. The Conbraco Air Gap Drain (AGD) is designed to funnel minor relief valve discharges, due to line pressure fluctuations and /or minor check valve fouling, into the drainage system. Drain piping is easily attached to the drain’s threaded bottom. Note: The AGD is NOT designed to collect the full discharge capacity of the relief valve. Dimensions - in.(mm) – Weights - lbs.(kg) R.P. AGD Order 4D-200 Series Model No. Code 2-1/2" - 4" AGD2 40-200-X1 6" AGD2 40-200-X1

The AGD4A Air Gap Drains are manufactured in the USA of lightweight ABS plastic. The versatile ABS plastic allows drainage piping to be attached to the internal NPT threads or to the outside with a coupling and the appropriate cement or using a flexible pipe coupling.

Dimensions - in.(mm) – Weights - lbs.(kg) R.P. AGD Order 40 Series Model No. Code 1/4", 3/8", 1/2" AGD1 40-200-XA 3/4" & 1" AGD2 40-200-X1 1-1/4" & 2" AGD2 40-200-X1 2-1/2" & 3" AGD3 40-200-X2 4" AGD3 40-200-X2 6" AGD3 40-200-X2 8" AGD4 40-200-X3 10" AGD4 40-200-X3 Dimensions - in.(mm) – Weights - lbs.(kg) R.P. AGD4A RP 4A Series Model No. 40 Series 1/2", 3/4”, 1” AGD4A-1 1/4”, 3/8”, 1/2” 1-1/4" - 1-1/2" AGD4A-112 3/4”, 1” 2 AGD4A-2 N/A

A 14-3/8 (365) 15-7/8 (403)

A 8-7/16 (214) 9-1/2 (241) 11-1/4 (286) 19 (483) 20 (508) 21 (533) 22-11/16 (576) 25-11/16 (652)

A 6.5 (165) 8.5 (216) 10.0 (254)

B 5-1/8 (130) 5-1/8 (130)

B 5 (127) 5-1/8 (130) 5-1/8 (130) 9-7/8 (251) 9-7/8 (251) 9-7/8 (251) 12-11/16 (322) 12-11/16 (322)

B 3.4 (86) 4.1 (104) 5.3 (135)

1" 1" 1" 2" 2" 2" 3" 3"

Exit Piping Threads C 1" NPT 1-1/2" NPT 2" NPT

C 1" NPT 1" NPT

C NPT NPT NPT NPT NPT NPT NPT NPT

Wt./Ea 3.4 (1.54) 3.4 (1.54)

Wt./Ea 2.3 (1.04) 3.4 (1.54) 3.4 (1.54) 11.0 (4.99) 11.0 (4.99) 11.0 (4.99) 12.45(5.65) 12.45(5.65)

OD of C 1-1/4” Pipe 2” Pipe 2-1/2” Pipe

Wt. Ea .10 (.05) .20 (.10) .35 (.16)

(RP-4A) (RP-40) (RP-40) 1/4”-2” 2 1/2”-10”

38

Customer Service 1-704-841-6000

1/2”-2”

Accessories Backflow Preventers

Accessories Series IBVE-125

EPOXY COATED CAST IRON FULL PORT CLASS 125 FLANGED BALL VALVE The new Conbraco Series IBVE-125 ball valves feature an FDA-approved, heat fused epoxy coating, making them ideal for corrosive water service as well as food contact applications. They can be used in place of any IBBM gate valve or plug valve. With their full port design, these valves assure an unobstructed, turbulence-free flow that gate and butterfly valves can’t match. Low profile handle for easy installation in tight places. Sizes from 21/2" to 8". Rated 125 WSP, 200 WOG, with maximum operating temperature of 140°F.

FEATURES • •

MATERIALS Body Seats

FDA Approved epoxycoated cast iron PTFE

• • •

Full port design offers superior flow rate No bronze seat rings, disc rings or stems to wear out Quarter turn offers instant, positive shutoff with zero leakage Stainless steel ball resists corrosion Large actuator mounting pad standard

• • • • • •

Dimensions (in.) – Weights (lbs.) Model # SIZE A B 6Q20901 2-1/2" 7.5 7 6Q20001 3" 8 7.5 6Q20A01 4" 9 9 6Q20C01 6" 10.5 11 6Q20E01 *8" 11.5 13.5

Handle indicates valve operation status Opens and closes easily, without cheater bar Blowout-proof stainless steel stem PTFE seats and packing, not Nitrile or EPDM Gear operator standard on 8" For more technical info ask for PHBRIRBV brochure

C 5.9 6.2 7 10.04 15.85

D 16 16 19.7 26 -

1/2 1/2 1/2 3/4 3/4

E WT./LBS NPT 34 NPT 38 NPT 58 NPT 118 NPT 345

NOTE: Gear operator standard on 8"

www.apollovalves.com

39

Accessories Backflow Preventers

Accessories Two-Piece Full Port Shut-Off Valves FULL-PORT HYDRO VALVE WITH DOUBLE FEMALE NPT Design features tee handle and side tapping; can be used as a drain feature or with 1/8" and 1/4" test cocks. Valve offers extended service life with its chromium-plated ball, PTFE seats and stainless steel handles.

FEATURES 7B-100 Series

• Stainless steel lever handles 1-1/4”-2” • Blowout-proof stem design • 125 psig SWP

• Rated 400 psig CWP, non-shock • Adjustable packing • Stainless steel t-handles 1/4”-1” Model Number 7B-101-01 7B-102-01 7B-103-01 7B-104-01 7B-105-01 7B-106-01 7B-107-01 7B-108-01

Size (in.) 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2

A 0.37 0.37 0.50 0.75 1.00 1.25 1.50 2.00

B 1.03 1.03 1.09 1.28 1.66 1.87 2.05 2.47

Dimensions (in.) C D E F 2.06 1.37 2.68 0.93 2.06 1.37 2.68 0.93 2.18 1.43 2.68 1.00 2.68 1.62 3.00 1.12 3.43 1.90 4.00 1.31 3.87 2.18 4.00 1.62 4.22 2.60 5.62 1.81 5.02 2.95 5.62 2.18

G 0.53 0.53 0.53 0.75 0.94 1.15 1.31 1.68

H 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 1/4 NPT

MALE X FEMALE FULL-PORT HYDRO BALL VALVE Eliminates leak path and need for extra nipples. Full-Port design assures full flow and minimum pressure drop. Long-life features include adjustable packing gland, chromium-plated ball, PTFE seats and stainless steel handles.

FEATURES

7B-800 Series

• Stainless steel t-handles 1/4”-1” • Stainless steel lever handles 1-1/4”-2” • 400 psig CWP, non-shock

• Rated 125 psig for saturated steam • -31 option: boss not drilled & tapped Model Number 7B-801-01 7B-802-01 7B-803-01 7B-804-01 7B-805-01 7B-806-01 7B-807-01 7B-808-01

Size (in.) 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2

Dimensions (in.) A B C D E F 0.37 1.40 2.43 1.37 2.56 0.93 0.37 1.46 2.50 1.37 2.56 0.93 0.50 1.68 2.78 1.43 2.56 1.00 0.75 1.88 3.28 1.70 2.68 1.12 1.00 2.39 4.17 1.93 3.62 1.31 1.25 2.66 4.66 2.13 3.62 1.62 1.50 2.86 5.03 2.71 5.12 1.81 2.00 3.34 5.89 3.06 5.12 2.18

BRONZE BALL VALVE TEST COCKS Male x Female Threaded. 400 psig CWP, non-shock. Air & liquid service.

FEATURES 78-290 Series

• • • •

Micro-finish ball Blow-out-proof stem design PTFE seats Nitrile stem seal

• • •

IPS & SAE flare connectons Compact design Screwdriver slot

BRONZE INSTRUMENTATION BALL VALVE TEST COCK - Screw Slot Model Size Dimensions (in.) Number (in.) A B C D E Cv Wt. 78-290-01 1/8M X 1/4F 0.21 0.80 1.60 0.72 N/A 4.00 0.19 78-291-01 1/4M X 1/4F 0.31 0.80 1.60 0.72 N/A 5.50 0.19 78-292-01 1/8 X 1/4 SAE Flare 0.31 0.80 1.60 0.72 N/A 5.50 0.22 78-293-01 1/4 X 1/4 SAE Flare 0.31 0.80 1.60 0.72 N/A 5.50 0.22

40

Customer Service 1-704-841-6000

G 0.53 0.53 0.53 0.75 0.94 1.15 1.31 1.68

1/8 1/8 1/8 1/8 1/8 1/4 1/4 1/4

H NPT NPT NPT NPT NPT NPT NPT NPT

Backflow Shut-Off Valves

Outside Stem & Yoke (OS&Y)

Non-Rising Stem (NRS) Size 2-1/2” 3” 4” 6” 8” 10”

Flg x Flg W-6785-00 W-6786-00 W-6743-00 W-6744-00 W-6827-00 W-6858-00

Flg x Grv W-5310-00 W-5311-00 W-5312-00 W-5313-00 W-5314-00 W-5315-00

Grv x Grv W-9369-00 W-9370-00 W-9371-00 W-9372-00 W-9373-00 N/A

Size 2-1/2” 3” 4” 6” 8” 10”

Flg x Flg W-6789-00 W-6790-00 W-6824-00 W-6825-00 W-6826-00 W-6829-00

Flg x Grv W-4733-00 W-4734-00 W-4735-00 W-4736-00 W-4737-00 W-4738-00

Grv x Grv W-5282-00 W-5283-00 W-5284-00 W-5285-00 W-5286-00 W-5231-00

Flange x Groove Shown

Groove x Groove Shown

Post Indicator (PI) Size 3” 4” 6” 8” 10”

Flg x Flg W-4478-00 W-4366-00 W-4367-00 W-4368-00 W-4369-00

Flg x Grv W-9125-00 W-9126-00 W-9127-00 W-9128-00 W-9129-00

Monitored Butterfly Grv x Grv W-9236-00 W-9237-00 W-9238-00 W-9239-00 N/A

Size 2-1/2” 3” 4” 6” 8” 10”

Grv x Grv W-5244-00 W-5245-00 W-5246-00 W-5247-00 W-5248-00 W-5249-00

Groove x Groove Only

Flange x Flange Shown

Cast Iron Ball Valve

Flange x Flange Only

Size 2-1/2” 3” 4” 6” 8”

Flg x Flg 6Q-209-01 6Q-200-01 6Q-20A-01 6Q-20C-01 6Q-20E-01

Bronze Ball Valve Size Inlet FxFNPT Outlet FxFNPT Inlet FxMNPT Outlet FxMNPT 1/4” 7B-101-01 7B-101-31 7B-801-01 7B-801-31 3/8” 7B-102-01 7B-102-31 7B-802-01 7B-802-31 1/2” 7B-103-01 7B-103-31 7B-803-01 7B-803-31 3/4” 7B-104-01 7B-104-31 7B-804-01 7B-804-31 1” 7B-105-01 7B-105-31 7B-805-01 7B-805-31 1-1/4” 7B-106-01 7B-106-31 7B-806-01 7B-806-31 1-1/2” 7B-107-01 7B-107-31 7B-807-01 7B-807-31 2” 7B-108-01 7B-108-31 7B-808-01 7B-808-31

www.apollovalves.com

FNPT x MNPT Shown

41

Available Assembly Shut-Off Valve Options Option Designation

Option Designation Part # Option

Model # Option

Part # Option

Model # Option

-01

-LS

-07

-OFG

Less Shut-Off Valves

-02

OS&Y Flange x OS&Y Groove

-08

-NF

-OG

NRS Flange x Flange OS&Y Groove x OS&Y Groove

-03

-09

-OF

-BG

Butterfly Groove x Butterfly Groove

OS&Y Flange x Flange

-04

-10

-OFBG

-OFPIG

OS&Y Flange x Post Indicator Groove

OS&Y Flange x Monitered Butterfly Grooved

-05

-11

-FBV

-NG

NRS Groove x NRS Groove

Ball Valve Flange x Ball Valve Flange

-06

-12

-OFPIF

OS&Y Flange x Post Indicator Flange

42

Customer Service 1-704-841-6000

-NFG

NRS Flanged x Groove

APPROVALS** TYPE OF DEVICE

MODEL

ORDER CODE

SIZE

APPROVALS USC

Double Check Double Check Double Check Double Check Double Check Carbonated Beverage Back.Prev Reduced Pressure Reduced Pressure Reduced Pressure Reduced Pressure Reduced Pressure Reduced Pressure Dual Check Dual Check Dual Check Atmospheric Port Pressure Vacuum Breaker Pressure Vacuum Breaker Spill-Resistant SVB Double Check Detector Assy Double Check Detector Assy Reduced Pressure Detector Assy Reduced Pressure Detector Assy Atmospheric Vacuum Breaker Atmospheric Vacuum Breaker Hose Conn. Vacuum Breaker Hose Conn. Backflow Dual Check Anti-Freeze Hose Con. V.B Lab Faucet Dual Check

DC-4A DC-40 DC-4S DC-4S DC-4SG CBBP RP-40 RP-4A RP-40S RP-40N/Z RP-40 RP-4D DUC-40 DUC-4N DCAP PVB-4A PVB-4V SVB DCDA-4SG DCDA-4S RPDA-40 RPDA-4D AVB1 AVB2 HVB HBDUC HBVB LFDUC

4A-100 40-100 4S-100 4S-100 4SG-100 4C-100 40-200 4A-200 40-200-T2S 40-20-T2N/Z 40-200 4D-200 40-300 4N-300 40-400 4A-500 4V-500 4W-500 4SG-600 4S-600 40-700 4D-700 38-100 38-200 38-304 38-304-02 38-404 38-500

1/2”-2” 3/4”-2” 1/2” 10” 2-1/2”-8” 1/4”-3/8” 1/4”-2” 1/4”-2” 1/4”-1” 3/4”-2” 2-1/2”-10” 2-1/2”-10” 1/2”-1” 3/8”-1” 1/2”-3/4” 1/2”-2” 1/2”-2” 1/4”-1/2” 2-1/2”-8” 2-1/2”-10” 3”-10” 2-1/2”-10” 1/4”-2” 1/4”-3/4” 3/4” 3/4” 3/4” 1/4”-3/8”

Pending Yes Yes Yes Yes N/A Yes Pending Yes Yes Yes Pending N/A N/A N/A Pending Yes Yes Yes Yes Yes Pending N/A N/A N/A N/A N/A N/A

ASSE 1/2”-2” 1015 1015 1015 1015 1022 1013 1/2”, 2” 1013 1013 1013 1013 1024 1024 1012 1/2”-2” 1020 1056 1048 1048 1047 1047 1001 1001 1011 1052 1011 1035

CSA

IAPMO

AWWA

UL*

FM*

Pending B64.5 B64.5 B64.5 B64.5 B64.3.1 B64.4 Pending Pending B64.4 B64.4 B64.4 B64.6 B64.6 B64.3 Pending B64.1.2 B64.1.2 B64.5 N/A N/A N/A B64.1.1 B64.1.1 B64.2 Pending B64.2 B64.7

Pending Yes Pending Yes Pending Yes Yes Pending Pending Pending Yes Pending N/A N/A N/A Pending Yes Yes N/A N/A N/A N/A Yes Yes Yes Pending Yes Yes

Pending C-510 N/A C-510 C-510 N/A C-511 Pending N/A N/A C-511 C-511 N/A N/A N/A N/A N/A N/A C-510 N/A N/A N/A N/A N/A N/A N/A N/A N/A

Pending 3/4”-2” N/A Yes Yes N/A 3/4”-2” Pending 3/4”-1” N/A N/A Yes N/A N/A N/A N/A N/A N/A Yes Yes Yes Yes N/A N/A N/A N/A N/A N/A

Pending N/A N/A Yes Yes N/A N/A N/A N/A N/A N/A Yes N/A N/A N/A N/A N/A N/A Yes Yes Yes Yes N/A N/A N/A N/A N/A N/A

Approved for horizontal and vertical installation * Must have indicating type shut-off valves ** Consult with factory for current approval details Note: For specific USC approved devices, please see the “FCCCHR” official listing. 4S-100 Series is listed as Model DC and 4S-600 is listed as Model DCDA on USC list.

WARRANTY & LIMITATIONS OF LIABILITY Conbraco Industries, Inc. warrants, to its initial purchaser only, that its products which are delivered to this initial purchaser will be of the kind described in the order or price list and will be free of defects in workmanship or material for a period of two years from the date of delivery to you, our initial purchaser. Should any failure to conform to this warranty appear within two years after the date of the initial delivery to our initial purchaser, Conbraco will, upon written notification thereof and substantiation that the goods have been stored, installed, maintained and operated in accordance with Conbraco’s recommendations and standard industry practice, correct such defects by suitable repair or replacement at Conbraco’s own expense. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHER WARRANTY, WHETHER EXPRESSED OR IMPLIED, EXCEPT THE WARRANTY OF TITLE AND AGAINST PATENT INFRINGEMENT. Correction of nonconformities, in the manner and for the period of time provided above, shall constitute fulfillment of all liabilities of Conbraco to our initial purchaser, with respect to the goods, whether based on contract, negligence, strict tort or otherwise. It is the intention of Conbraco Industries, Inc. that no warranty of any kind, whether express or implied shall pass through our initial purchaser to any other person or corporation. LIMITATION OF LIABILITY: Conbraco Industries, Inc. SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR SPECIAL OR CONSEQUENTIAL DAMAGES SUCH AS, BUT NOT LIMITED TO, DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF PROFITS OR REVENUE, COST OF CAPITAL, COST OF PURCHASED OR REPLACEMENT GOODS, OR CLAIMS OF CUSTOMERS OF OUR INITIAL PURCHASER. THE REMEDIES OF OUR INITIAL PURCHASER, AND ALL OTHERS, SET FORTH HEREIN, ARE EXCLUSIVE, AND THE LIABILITY OF CONBRACO WITH RESPECT TO SAME SHALL NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE CONBRACO GOODS UPON WHICH SUCH LIABILITY IS BASED. IT IS THE END USER’S RESPONSIBILITY TO CONFIRM THAT ITEMS INTENDED FOR USE SATISFY LOCAL CODES AND STANDARDS. www.apollovalves.com

43

Manufactured by Conbraco Industries, Inc. SALES AND SERVICE DEPARTMENT PO Box 247 • Matthews, NC 28106 Phone: 704-841-6000 • Fax: 704-841-6020 Fax

B. Lynch & Associates Spotswood Associates Pro Marketing, Inc. Mid South Marketing, Inc.

Florida Georgia/Alabama North Carolina/South Carolina/Tennessee-East Virginia/Maryland/Washington, D.C./WV-East

[email protected] [email protected] [email protected] [email protected]

813-792-5060 770-447-1227 864-578-4334 804-213-3801

813-792-5213 770-263-6899 864-578-4889 804-213-3802

Southern Marketing Group AVC Mechanical Sales, Inc. Armstrong/Weatherly Associates Lightsey Marketing

MS/TN-West/AR/Bowie Cty.-TX Oklahoma (Plmb & Ind’l)/Texas-North (All) Texas-South/Louisiana Oklahoma (Irrigation, Fire Protection, Water Works)

[email protected] [email protected] [email protected] [email protected]

901-547-0042 214-201-0100 713-692-5566 918-251-2828

901-547-0035 214-201-0104 713-692-6021 918-251-7742

HEBCO, Inc. New Tech Marketing New Tech Marketing Whitfill-McCarthy, LLC V.E. Sales Co., Inc. Formation Sales Marshall-Rodeno Heartland Midwest Spec Warren Thoma Associates

Kansas/Missouri-West IL/WI-East/IN-North/MI-Upper Peninsula/IA-/River Counties Eastern Missouri/Southern Illinois Kentucky/Indiana-South/Ohio-South Michigan (Except Upper Peninsula) Minnesota/North & South Dakota/Wisconsin-West Nebraska/Iowa (Except River Counties) Ohio-North/Pennsylvania-West/West Virginia-West MI/WI/IL/IN/KY/OH (Irrigation Only

[email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected]

913-491-0797 630-378-4300 618-394-0329 502-459-4545 586-774-7760 763-262-4700 303-575-6701 330-538-0406 815-477-1814

913-491-5126 630-378-0343 618-394-0427 502-459-9944 586-774-1490 763-262-4740 303-575-6706 330-538-0410 815-477-2009

Elmco and Associates Spec Management Group Cisco Speciality Products, Inc. Marshall-Rodeno Associated Braley-Gray & Associates Braley-Gray Washington Southwestern Industrial Sales Co. Jack Prust Sales Active Sales Northwest, Inc

California-North California-South (Irrigation), Hawaii (All Products) California-South CO/WY/MT/ID-SE/UT/NV-NE/NM/El Paso-TX Oregon/SW Washington/Western Idaho Alaska/Washington Arizona/Nevada-SW California-North (Irrigation) Oregon, WA, Western Idaho (Irrigation)

[email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected]

916-383-0110 949-481-4225 714-921-9228 303-575-6701 503-249-6972 206-405-4370 480-458-5838 530-878-2922 541-726-0320

916-383-0181 949-487-0990 714-921-0442 303-575-6706 503-288-4464 206-405-4390 480-458-5843 530-878-2341 541-726-1148

Urell, Inc. McMahon Marketing, Inc. Conroy & Griese Sales, Inc. Layden Company Keith Engle & Associates Waterlines, Inc.

Massachusetts/New England States New York-Upstate/New York-West New York-East/New Jersey-North Pennsylvania-East/Delaware/New Jersey-South OEM accounts New England/Upstate, Metro NY/PA/VA (Irrigation Only)

[email protected] [email protected] [email protected] [email protected] [email protected] [email protected]

617-923-9500 518-792-3350 856-663-4440 610-363-6657 610-827-9560 973-209-7777

617-926-9414 518-792-3351 856-663-6644 877-529-3361 610-827-9561 973-209-7421

Conbraco Industries, Canada Barclay Sales Ltd. Dynamic Agencies, Ltd. Tom Beggs Agencies Ltd. Task Controls, Inc. Agences J. Pierre Sylvain, Inc. Kern Industries, Ltd. Kern Industries Calgary, Ltd. J. Levandier Sales, Inc.

160 Pennsylvania Ave., Unit 3, Concord, Ontario L4K 4A9 British Columbia Saskatchewan Manitoba/NW Ontario Ontario Quebec Alberta-North Alberta-South Nova Scotia, New Brunswick, Prince Edward Island and Newfoundland Ontario-North Ottawa

[email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected]

905-761-6161 604-945-1010 306-343-1901 204-953-1900 416-291-3004 450-655-9588 780-451-2056 403-730-7791

905-761-6666 604-945-3030 306-343-1901 204-774-6915 416-754-3481 450-641-2737 780-454-6687 403-239-8179

506-858-1615 705-524-6714 1-800-363-8482

506-858-1084 705-566-0148 514-457-7111

Canada

Northeast Region

Western Region

Midwestern Region

Southeast Region

Phone

Southern Region

E-Mail Address

Int’l.

Key to the North Sales Agency, Inc. Steam and Industrial Equipment

[email protected] [email protected] [email protected]

Sadek Trading

Middle East (ex Israel)

[email protected]

704-618-6613

980-233-8437

Conbraco International Sales:

Mexico

[email protected]

956-631-4542

956-631-4681 954-252-8698

Caribbean

[email protected]

954-252-9781

Central & South America

[email protected]

506-8836-0759

Asia Pacific

[email protected]

65-9626-9241

65-6753-0131

Europe

[email protected]

44-161-212-3745

44-161-212-3747

Africa/Australia/Israel/India

[email protected]

954-252-9781

954-252-8698

Conway, SC • Matthews, NC • Pageland, SC • Customer Service 1-704-841-6000 • www.apollovalves.com Printed in USA Copyright 2/09 BP 7.5M

BFCA9000