MONTAGEANLEITUNG ekey home (net) integra HINWEIS ZUM DOKUMENT Diese Montageanleitung als auch die zusätzlichen Informationen und Anleitungen auf der beiliegenenden DVD unterliegen keinem Änderungsdienst. Die letztgültige Version dieser Dokumente finden Sie unter www.ekey.net. Optische und technische Änderungen, Satz- und Druckfehler bleiben vorbehalten. ACHTUNG ! Bitte beachten Sie zu dieser Anleitung unbedingt auch die Informationen auf der beiliegenden DVD.

AUSFRÄSUNG

* empfohlene Fräsmasse (können je nach Werkstoff variieren)

LIEFERUMFANG FINGERSCANNER

DICHTUNG

STEUEREINHEIT

2 STK. SCHRAUBEN LK 2.9 X 19

2 STK. SCHRAUBEN LK 2.9 X 38

DEKORELEMENT

ANLEITUNG

DVD

MONTAGE EKEY HOME (NET) INTEGRA - FINGERSCANNER MONTAGEHÖHE Fingerscanne r

Die vorgeschriebene Montagehöhe für den Fingerscanner liegt bei mindestens 155cm oder höher !

Steuereinhei t

155cm

m

m

130cm 130

c

Nur bei Montage in der richtigen Höhe ist eine gute Bedienung und damit eine einwandfreie Funktion gewährleistet!

Für den Einbau ohne Montagedübel (z.B. in einen Türrahmen) müssen die am Gehäuse angebrachten Dübel abgeschnitten werden. BEFESTIGUNG IM TÜRBLATT

Bevor Sie den Fingerscanner und Steuereinheit montieren ist eine entsprechende Ausfräsung im Türblatt bzw. Türstock erforderlich. Beachten Sie bitte bei der Montage, dass auf beiden Seiten des Fingerscanners etwa eine handbreit Platz bleiben soll, um so eine problemlose Funktion des Gerätes mit allen Fingern zu gewährleisten

MONTAGE ekey home Aufputz AUSFRÄSUNG UND MONTAGE EKEY HOME (NET) INTEGRA STEUEREINHEIT Türblatt

Ausfräsung für die Inneneinheit integra Bohrungen f. Befestigungsschrauben (optional)

TECHNISCHE DATEN Technische Daten ekey home (net) Fingerscanner integra Versorgung

Einheit VAC VDC W °C Finger FAR

Leistungsaufnahme Temperaturbereich Speicher Sicherheit

30.0

8-24 8-30 ca.1 -40 bis +85 home:99 net: 40/200/2000 1x 10-6 1,4x 10-2

FRR Schutzart Geschwindigkeit Lebendauer

IP s Fingerscans

Technische Daten ekey home (net) Steuereinheiten integra

Einheit

Versorgung

X


OK 273.00

254.00 233.25 Auslass für Kabelzuführung (von Außeneinheit, Motorschloss und Hauptzuleitung, die Position der Ausnehmung ist frei wählbar)

min. 8mm

Leistungsaufnahme Relais RELAIS Schaltleistung Relais Maximale Spannung (Peak AC) EIN- Widerstand (max.) Leckstrom Einschaltzeit Ausschaltzeit Temperaturbereich Schutzart Digitale Eingänge Maximaler Strom an X6 PIN 1 (nur bei Integra)*

VAC VDC W Anzahl

VAC(DC) Ω µA ms ms °C IP A

54 (frontseitig) 1-4 max. 4 Mio ekey integra

home

ekey home integra 2, pc ekey net integra

8-24 8-30 ca.1 1

8-24 8-30 ca.1 2

42VDC(AC)/2A 60 0,12 1 1.5 0.5 -40 bis +85 40 (Frontseite) 1 3

42VDC(AC)/2A 60 0,12 1 1.5 0.5 -40 bis +85 40(Frontseite) 1 3

Es steht 1 Relais (2 Relais in der Variante ekey home 2, pc und ekey net) zum Ansteuern von externen Geräten zur Verfügung. Relais 1 verfügt über einen potentialfreien bzw. potentialbehafteten Schließer der über JP1 konfigurierbar (Ist JP1 nicht bestückt, so ist immer der potentialbehaftete Schließer in Funktion) ist. Relais 2 ist generell potentialfrei und kann über JP2 als Öffner oder Schließer konfiguriert werden. Die maximale Schaltleistung beträgt 42V / 2A. Das Verbindungskabel zwischen Steuereinheit und Fingerscanner ist getrennt von der Hauselektroinstallation zu verlegen, da dieses Signale im Niederspannungsbereich führt, die durch benachbarte stromführende Kabel gestört werden können.

Fräsbreiten: 18mm, 20mm oder 24mm

Die Anschlüsse sind nicht verpolungsgeschützt! Ein falscher elektrischer Anschluss des Systems kann zur Zerstörung des Gerätes führen. Die Herstellung der elektrischen Verbindungen und der Anschluss an die Netzversorgung darf ausschließlich durch Fachpersonal durchgeführt werden!

PINBELEGUNG EKEY HOME (NET) INTEGRA

F Ü R V E R A R B E I T E R

X3- Verbindung zu RS485 (KLEMME 2) RS485 (KLEMME 1) Versorgung für Fingersc. (KLEMME 3) Versorgung für Fingersc. (KLEMME 4)

Arbeitsweise Relais 1

Kabel Typ A Farbe

PIN

Fingerscanner

JP1

1 2 3 4

X3

gelb grün braun weiss

Arbeitsweise Relais 2

Belegung RJ45

3

1

4

2

Kabel Typ A

JP2

5 4 7

Kabel Typ A Farbe gelb grün braun

8

weiss

PIN

RS485 (KLEMME 2) RS485 (KLEMME 1) Versorgung für Fingersc. (KLEMME 3) Versorgung für Fingersc. (KLEMME 4)

8 1

X3 Funktion potentialfrei, Schließer (NO) Funktion = Schaltspannung (Werkseinstellung)

mit

X6

– RELAIS Funktion

23

Funktion Schließer (NO)

X6

1

Anschluss

2

PIN

1 2

rot 1 2 3

2 1

rosa

Schalteingang 1

1

blau

E L E K T R I K E R

Schalteingang 2

2

grau

RS485 (KLEMME 2)

3

gelb

RS485 (KLEMME 1)

4

grün

8

5

braun

Versorgung DC + oder AC

6

weiss

Relais 2 C

7

rosa

Relais 2 NO/NC je nach

8

rot

AC

7 3

6 2

5 1

Netzteil

Kabel Typ B

X6

Taster für manuelle Türöffnung z.B. bei Sprechanlage

3 2 1

blau grau

gruen gelb

8 7 6 5

oder

weiss braun

JP2

4

Kabel Typ B Farbe

F Ü R

RELAIS 2: Beispiel: Steuersignal für eine Alarmanlage (potentialfreier Kontakt)

JP1

3

3

X1 -

Hauptzuleitung

V E R A R B E I T E R

PIN

&

F Ü R

DC-

Kabel Typ C

1

JP1 = JP1 = mit POTENTIALFREI SCHALTSPANNUNG Kontakt C Versorgung Motorschloss (+) (common) (Spannung von von X1, Pin 6, weiss) FREI – NICHT Versorgung Motorschloss (-) BELEGEN (Spannung von X1, Pin 5, braun) Kontakt NO (= Schaltimpuls (Spannung Schließer) X1, Pin 6, weiss, wird hier über Relais 1 geschalten)

Versorgung

RELAIS 1 Motorschloss oder Türöffner: Anschluss entsprechend der Bedienungsanleitung des Motorschlosses durchführen !

3

4 2

3 2

Funktion Öffner (NC)

12

3 1

2 1

F Ü R

4 3 2 1

X1

Potentialfreier Kontakt notwendig

ekey converter LAN ekey converter UDP ekey converter USB *) 1 2 3 4

X1 Netzteil

*) bei ekey converter USB sind Klemme 3 und 4 (Power supply) nicht zu belegen.

E L E K T R I K E R

MONTAGE ekey home Aufputz VERKABELUNGSBEISPIEL EKEY HOME (NET) INTEGRA MIT TÜRÖFFNER UND EKEY TÜRÜBERGANG Die im folgenden Verkabelungsplan dargestellten Kabel sind Standardkabel von ekey, die sie fertig konfektioniert, in unterschiedlichen Längen bei ekey erhalten können. Kabel Typ A: Verbindung Steuereinheit – Fingerscanner Kabel TypB: Verbindung zu externen Systemen Kabel Typ C: Verbindung Steureinheit Motorschloss (Türöffner) Die Zuweisung der Adernfarben, ist natürlich nur bei Verwendung dieser Kabel gültig ! Generell empfiehlt ekey die Verwendung obgenannter Kabel !

Kabel Typ A

X3

Kabel

Typ grün (+) Switch

Kabel Typ A

X6

F Ü R

3 2 1

braun (-) Gnd weiss (+) VCC

Kabel Typ C

X1 Kabel Typ B

blau grau gelb grün braun weiss rosa rot

Schalteingang 1 Schalteingang 2 RS485 (Kl.2) RS485 (Kl.1) (-)VCC (Kl.3) (+)VCC (Kl.4) REL2 C REL2

801066: Version 4 vom 16.12.09

Kabel Typ B1

E L E K T R I K E R

F Ü R

Belegung Motorschloss (Beispiel)

Kabel Typ C

Kabel Typ C

ekey Kabelübergang 100880 100881

weiss

(+) VCC

braun

(-) Gnd

grün (+)Switch

1 2 3

Fragen Sie nach Anschlussplänen für verschiedene Schlosstypen bei ekey.

Steuereinheit und Fingerscanner müssen mit einem 4-adrigen Kabel mit 0,14 mm² Aderquerschnitt verbunden werden. Bei Distanzen über 50 m muss für die stromführenden Adern (Anschlüsse 3 u. 4) ein Kabel mit größerem Aderquerschnitt gewählt werden. Die maximale Leitungslänge zwischen Fingerscanner und Steuereinheit beträgt 500m.

V E R A R B E I T E R

ASSEMBLY INSTRUCTIONS ekey home (net) integra NOTE ON THE DOCUMENT

Corner or radius 5mm

These assembly instructions as well as the additional information and instructions on the supplied DVD are not subject to updating. You can find the most up to date version of these documents at www.ekey.net. Subject to optical and technical amendments, as well as printing and typing errors WARNING ! Please also observe the information on the supplied DVD as well as these instructions.

COUNTER-SINK (on all 4 corners)

* recommended milling dimensions (can vary depending on the material)

DELIVERY CONTENTS FINGERSCANNER

2 X SCREWS LK 2.9 X 19

SEAL

CONTROL PANEL

2 X SCREWS LK 2.9 X 38

INSTRUCTIONS

DVD

DECORATIVE ELEMENT

ASSEMBLY OF THE EKEY HOME (NET) INTEGRA – FINGERPRINT SCANNER

Version 1 (installation screw anchors)

Version 2 (screws)

MOUNTING HEIGHT Fingerprint

Fingerscanne scanner r

The specified mounting height is 135cm or higher!

Steuereinhei Control t panel

155cm

m

m

130cm 130

Only by mounting the device at the correct height can guarantee good operation and thereby flawless functioning !

For mounting without assembly screw anchors (e.g. in a door frame) the screw anchors applied to the casing have to be cut off. ATTACHMENT TO THE DOOR LEAF

c

Before you mount the fingerprint scanner and control panel, a counter-sinking in the door leaf or door frame is necessary.

During installation please make sure that there is a space of approx. one hand’s width on both sides of the fingerprint scanner, in order to guarantee that the device functions without a problem.

MONTAGE ekey home Aufputz COUNTER-SINKING AND MOUNTING OF THE EKEY HOME (NET) INTEGRA CONTROL PANEL Türblatt DOOR

LEAF

COUNTERSINKING FOR THE

TECHNICAL DATA Technical data ekey home (net) scanner integra Power supply

Unit

Power input Temperature range Memory

V AC V DC W °C Fingerpts

Security

FAR

Ausfräsung für die INDOOR Inneneinheit INTEGRA UNIT integra

Hole for the fastening Bohrungen f. Befestigungsschrauben (optional) screws (optional) 30.0

Protection class Speed Life cycle

X


OK

ekey home integra ekey net integra

fingerprint

min. 8mm

1 relay (2 relays area available in the ekey home 2 and PC version) is available for controlling external devices. The programming is carried out via the programming menu. Relay 1 has a potential-free or non-isolated closing contact which can be configured via JP1.(if JP1 is not assembled, Relay 1 works non isolating) Relay 2 is generally potential-free and can be configured via JP2 as an opening or closing contact. The maximum switching capacity is 42V / 2A. The connection cable between the control panel and the fingerprint scanner is to be laid separately from the electrical installations of the building, as these signals produce a low-voltage area which can be impaired by adjacent live cables. Fräsbreiten: 18mm, 20mm oder 24mm

Widths of cuts: 18mm, 20mm or 24mm

The connections do not have reverse polarity protection! An incorrect electrical connection of the system can cause damage to the device. The creation of the electrical connection and the connection to the mains can only be carried out by specialists!

PIN ASSIGNEMENT EKEY HOME (NET) INTEGRA

F O R D O O R P R O D U C E R

X3

Connection to the fingerprint scanner RS485 (TERMINAL 2) RS485 (TERMINAL 1) Power supply to the fingerprint scanner (TERMINAL 3)) Power supply to the fingerprint scanner (TERMINAL 4)

Functioning of relay 1

JP1

Function of the potential-free contact (NO) Funktion = mit Function = with switched voltage (factory setting)

X6

– RELAY function JP1 = POTENTIAL -FREE Contact C (common) FREE – NOT OCCUPIED NO contact (= normally open)

1

Typ A cable colour

PIN 1 2 3

yellow green brown

4

3 4

white

Functioning of relay 2

JP2

12

Function contact (NO)

of

Function contact (NC)

of

connection

&

1

Typ A cable

2

ASSIGNMENT RJ45

PIN

RS485 (TERMINAL 2) RS485 (TERMINAL 1) POWER Supply (TERMINAL 3) POWER Supply (TERMINAL 4)

5 4 7 8

2 1

3

4 2

X6

3 2

Typ C cable

8 1

2 1

PIN

F O R

RELAY 2: example: control signal for an alarm system (potential-free contact)

Power supply for the motorised lock (+) (voltage from X1, pin 6, white) Power supply for the motorised lock (-) (voltage from X1, pin 5, brown) Switching pulse (voltage X1, pin 6, white, is switched here by relay 1)

PIN

D O O R P R O D U C E R

RELAY 1 MOTORISED LOCK OR DOOR OPENER: Connect in accordance with the operating instructions of the motorised lock!

JP1 = with SWITCHED VOLTAGE Contact C (common) FREE – NOT OCCUPIED NO contact (= normally open) Typ B cable colour

F O R

X1 -

Switching input 1

1

blue

E L E C T R I C I A N

Switching input 2

2

grey

RS485 (TERMINAL 2)

3

yellow

RS485 (TERMINAL 1)

4

green

main supply

TYPA cable colour yellow green brown white

X3 3 1

23

F O R

X3

DC-/AC Power Supply (TERM. 3)

5

brown

DC+ /AC Power Supply (TERM. 4)

6

white

RELAY 2 C

7

pink

RELAY 2 NO/NC depending

8

red

1 2 3

red

JP1

3 2 1

pink

white brown

JP2 8 4

7 3

6 2

Power Supply

5 1

Typ B cable

X6 Switch FOR OPENING THE DOOR MANUALLY e.g. with intercom

3 2 1

blue grey

green yellow

8 7 6 5 4 3 2 1

X1

Use only potential free contact !!

ekey converter LAN ekey converter UDP ekey converter USB *) 1 2 3 4

X1 Power Supply

*) WITH EKEY CONVERTER USB, TERMINALS 3 and 4 (power supply) are not to be assigned.

E L E C T R I C I A N

MONTAGE ekey home Aufputz WIRING EXAMPLE FOR EKEY HOME (NET) INTEGRA WITH A DOOR OPENER AND EKEY DOOR CABLE TRANSFER THE CABLES AND STANDARD CABLES SHOWN IN THE FOLLOWING WIRING PLAN FROM EKEY, WHICH THEY MANUFACTURE, ARE AVAILABLE IN DIFFERENT LENGTHS FROM EKEY. Type A cable: control panel – fingerprint scanner connection Type B cable: connection to external systems Type C cable: control panel – motorised lock (door opener) connection The allocation of the wire colours is, of course, only valid when using these cables! In general ekey recommends that the above-mentioned cables are used!

X3

Kabel

cable Typ A

F O R

green (+) Switch

D O O R

Typ

cable Typ A

F O R

X6

3 brown (-) Gnd Cable 2 white (+) VCC Typ C 1

X1

E L E C T R I C I A N

blue grey yellow gree brown white pink red

Input 1 Input 2 RS485 (Kl.2) RS485 (Kl.1) (-)VCC (Kl.3) (+)VCC (Kl.4) REL2 C REL2

801066: Version 4 vom 16.12.09

Kabel Typ B1

cable Typ B

pinning motor lock (example) cable Typ C

cable Typ C

ekey door tabel transfer 100880 100881

white

(+) VCC

brown

(-) Gnd

green (+)Switch

1 2 3

Check the Datasheet of the motor lock, before you connect it to the ekey home control panel!

The control panel and the fingerprint scanner must be connected with a 4-core cable which has a core diameter of 0.14mm2. For distances of over 50m a cable has to be selected with a larger core diameter for the live cores (connections 3 and 4). The maximum cable length between the fingerprint scanner and the control panel is 500m.

P R O D U C E R