LED Striplighting Kits Installation Manual
Please read this manual carefully before use This manual covers the following product codes: 3528-WW-N/352...
Please read this manual carefully before use This manual covers the following product codes: 3528-WW-N/3528-W-N/3528-RGB-N/5050-WW-N/5050-W-N/5050-RGB-N/3528-WWWT/3528-W-WT/3528-RGB-WT/5050-WW-WT/5050-W-WT/5050-RGB-WT
INTRODUCTION Thank you for purchasing a Biard LED striplighting kit. All products within these kits are manufactured to the highest standard. Please use in accordance with these instructions to ensure optimum performance and safety. Warning! Before installing or using the LED Striplighting Kit please ensure that these instructions have been carefully read with particular attention to all safety instructions, warnings and cautions. The product/s must be used correctly at all times for the purpose in which it is intended. Any damage and/or personal injury resulting from failure to comply with these instructions will invalidate the warranty. Please keep these instructions in a safe place for future use.
PRODUCT DESCRIPTION The Biard LED Striplighting Kits are designed by a team of electricians in the UK to the highest of industry standards. All components are CE and RoHS approved. All LED striplights referred to in this manual come in five meter lengths and are simple to set up. A M3 adhesive backing means you can install them quickly and easily virtually anywhere.
3|Page
APPLICATIONS
Cove lighting Architectural lights for canopy, corridor, windows and archways Backlight or edge lighting for signage DIY lights for home use Path and contour marking Decorative lights for Christmas, events, shows and exhibitions
SAFETY INSTRUCTIONS These LED Striplighting Kits are not intended for use by children. Additionally, any person with reduced sensory, physical or mental capabilities, or lack of experience and knowledge, must be instructed on how to use or install the kit by a person qualified to do so.
PRODUCT LIST 1 x 5m length of LED striplight 1 x 60W power supply 1 x LED controller with remote control (Only for the RGB striplighting)
SPECIFICATIONS Light Output (Lumen/M)
Beam Angle (Degree)
Voltage (VDC)
Current (Amps/M)
Max. Power Consumption (W/M)
IP Rating
Continuous Connection (Meters)
360
120
12
0.4
4.8
20
10
380
120
12
0.4
4.8
20
10
5
360
120
12
0.4
4.8
20
10
300
5
900
120
12
1.2
14.4
20
5
Cool White
300
5
1020
120
12
1.2
14.4
20
5
5050-RGB-N
RGB
300
5
900
120
12
1.2
14.4
20
5
3528-WWWT
Warm White
300
5
360
120
12
0.4
4.8
65
10
3528-W-WT
Cool White
300
5
380
120
12
0.4
4.8
65
10
RGB
300
5
360
120
12
0.4
4.8
65
10
Warm White
300
5
900
120
12
1.2
14.4
65
5
5050-W-WT
Cool White
300
5
1020
120
12
1.2
14.4
65
5
5050-RGBWT
RGB
300
5
900
120
12
1.2
14.4
65
5
Product Code
Color
LED QTY
Length Meter
3528-WW-N
Warm White
300
5
3528-W-N
Cool White
300
5
3528-RGB-N
RGB
300
5050-WW-N
Warm White
5050-W-N
3528-RGBWT 5050-WWWT
LED Type
3528 SMD
5050 SMD
3528 SMD
5050 SMD
4|Page
CONNECTING (Non RGB) 1. The striplights are connected to the power supply via the female jack plug from the striplighting and the male jack plug from the power supply as below.
Fig 1.1
Fig 1.2
CONNECTING (RGB) 1. The power supply is connected to the controller via the male jack plug from the power supply (Fig 1.1); the controller is then connected to the striplight via the female 4 pin connector from the controller to the male 4 pin connector from the striplight (Fig 1.2).
Fig 1.1
Fig 1.2
Fig 1.3
Fig 1.4
CUTTING The RGB and single coloured LED striplighting can be cut every 50mm on the indicated marks, as below.
Single Colour
RGB
5|Page
TROUBLESHOOTING If you are experiencing any problems with the LED striplighting or any components in the kit then this section may be able to help you solve the problem. If you have tried all the below and you are still having trouble then please call our customer services helpline. No power to the power supply (green LED light not lit)
Check the fuse in the power supply plug Make sure connections to the power supply are firmly pushed together
No power to the controller
Make sure all connections are firmly pushed together
LED lights not lit
Ensure all connections are good, check the lights are turned on via the remote (RGB only) Check the 4 pin plug (RGB only) is the correct way (remove and try opposite way)