I NSTAL L AT ION MANUAL C LAW FOOT TUB AND T E L E PH ON E ST Y L E FA UCET Itm # / Art. No 401377 | Model No. 3JPS007WHI001

R ea d compl e t e i nst r ucti ons befor e be gi nni ng i nstal l at i o n

1

B E F OR E YOU START

1.

Inspect your unit before proceeding. Check surface for any flaws or damage. Your unit has been manufactured with a cast acrylic sheet providing an extremely durable surface. Once you unpack your unit, check for chips, scratches, cracks, dents or scuff marks. If any damage is noticed, do not install. Talk to your retailer where the unit was purchased.

2.

Please read instructions carefully and keep for future reference.

3.

Protect the entire surface during installation.

4.

Make sure the floor structure is capable of supporting 100 lbs (45.5 kgs) per square foot.

5.

All holes drilled into the unit must be done from the inside (finished surface) towards the outside (rough surface) and caulked very carefully to form a water-tight barrier.

6.

Your installation must comply with all local plumbing codes.

IMPOR TAN T Have a qualified tradesman do and/or approve your plumbing installation. Have all plumbing work approved by a qualified inspector. DO A DRY RUN FIRST. Read all installation instructions first, then assemble all elements without plumbing, drilling or using any permanent sealants. This ensures that the tub, faucet and plumbing is in the correct location and all elements work together with new or existing plumbing. Only when you are satisfied that everything is in the correct location and all elements work together should final installation begin.

2

M AIN T UB PAR TS

M8 Screws x8

M10 Screws x8

Leveling foot x4

M10 Washers x8

M12 Nuts x4

Claw foot x4

Support arm x4

Acrylic tub x1

3

T UB IN STAL L AT ION

NOTE: A thorough inspection must be made at the time of pick up or delivery. If the unit is damaged, do not install. The installation of this tub requires 2 people. 1.

Carefully unpack the tub and contents from the packaging.

2.

Inspect all areas of the tub and parts to ensure there is no damage. If you discover any damage, do not install this unit.

3.

Place a blanket on floor to protect the finish of the tub.

4.

Place the tub upside down on the blanket, with the tub base facing up. See fig. 1.

5.

Using 2 M8 bolts, attach each claw foot to a support arm. Tighten. See fig. 2.

6.

Insert leveling legs into the bottom of each of the 4 support arms. See Fig.2.

Fig. 1

Fig. 2

7. Attach the 4 support arms (with attached claw feet) to the tub base using 8 of the supplied M10 screws and 8 M10 washers. See Fig.3. 8.

Carefully turn tub over to rest on all feet.

9. Postion tub in desired location. Fig. 3

10. Turn leveling legs to ensure the tub is completely level when placed in the desired location. 11. Once the tub is level, tighten the locking nuts on each leveling leg. See Fig.4.

Fig. 4

4

S U P P LY L IN E IN STAL LATI O N

Unpack and identify all parts and read through the instructions before beginning installation. Parts List:

90 degree water supply tube x2

30.5 cm (12 in) Wall support tube x2

Screws x 14

Coupling nut with rubber washer x2

Shut-off valve (hot & cold) x2

Wall support flange x2

Wall support connecting ring x2

Water supply nut x2

Tightening nut x2

5

Floor flange x2

Plastic anchor x 14

Rubber cone washer x2

S U P P LY L IN E IN STAL LATI O N

Tools required: Pencil / Philips screw driver / teflon tape / adjustable wrench / pipe cutters / measuring tape drill and drill bits / flathead screwdriver Step 1 Attach floor flange to shut-off valve. Floor flange should be rotated until the threads are not showing. Attach shut-off valve to existing water supply lines from undemeath. Secure floor flange with supplied anchors and screws (position shut-off valve at desired position) - FIG.1

Step 2 Remove rubber washer from coupling nut. Install coupling nut onto water supply line and then insert rubber washers onto coupling nut. - FIG.2 Step 3 Slide wall support connecting ring onto water supply line. Leave wall support connecting ring loose ready to be secured onto the wall. - FIG.2 Step 4 Apply a small amount of Teflon tape on the threaded part of the water supply line. Attach water supply lines onto shut-off valves and position 90 degree angle of water supply lines over the bathtub making sure that supply lines are firmly attached to shut-off valves. - FIG.3

6

S U P P LY L IN E IN STAL LATI O N

Step 5 Measure the distance from the wall to the wall support connecting ring. You may need to cut the 30.5 cm (12 in) wall support tubes to required length. Attach wall support flange to desired height onto the wall. Attach wall support tubes onto the wall support flange. - FIG.4

Step 6 Attach wall support rod onto connecting ring and tighten adjustment screws on connecting ring. - FIG.5 Step 7 Attach desired faucet to water supply line. - FIG.6

7

D R AIN IN STAL L ATI O N

Step 1 Use plumbers putty under the chrome drain and place into the tub drain opening and screw into place. Clean off any excess putty. Fig. 1

Plumbers Putty

Gasket

Fig. 1

Fig. 2

Step 2 Using the gasket supplied, put it under the tub and tighten the drain, making sure the pipe sticks out straight as in Fig. 1. Step 3 Each end of the "T" pipe has a plastic compression gasket and nut. Transfer the nut, then the compression gasket onto the pipes with the tapered side pointing towards the "T". Fig. 2 Step 4 Install the "T" onto the horizontal drain pipe, a lightly tighten the nut. Install the vertical pipe into the "T" and align the top with the overflow hole. Lightly tighten the nut on the "T". Fig. 3

8

Fig. 3

Fig. 4

Step 5 Install the tapered gasket between the tub and the vertical overflow pipe as shown. Install the gasket with the relief cutout and the cover plate using the screw provided. Fig. 4 Step 6 Install the tailpiece into the ABS pipe system with the nut and compression gasket facing up. Drop the tub with the now installed waste and over flow over the tailpiece, and tighten. Tighten all 3 nuts on the "T" using a wrench and a cloth to protect the finsh. Fig.5

Fig. 5 Step 7 Install the drain plug into the drain.

9

FA UCET IN STAL L ATI O N

Unpack and identify all parts and read through the instructions before beginning installation. Parts: Faucet body x 1 Shower head x 1 Hose x 1 Cradle x 1 Washer x 3

Note: handles are identified hot and cold. The hot handle is on the left and the cold to the right. CAUTION: Ensure the water supply is turned off before starting installation. Cushion the wrench or slip joint pliers with a cloth to protect the finish of the fixture. Installation 1. Attach the faucet body with coupling nut on the water supply line. 2.

Install washer in the cradle nut and thread the cradle onto the faucet body..

3.

Install washer in the hose ends and attach the hose to the cradle and shower head. Do not over-tighten.

Note: This unit does not have an anti scald mechanism.

10

C L E A NIN G AN D MAIN TENANCE

To maintain the smooth, high gloss surface of the tub, follow these tips: ✔✔ Use common household cleaners (non-abrasive) or a mild liquid dish washing detergent. Rinse well and dry with a clean cloth. ✔✔ Do not allow your acrylic surface to come into contact with products such as acetone (nail polish remover), nail polish, dry cleaning solution, lacquer thinners, gasoline, pine oil, etc. ✔✔ Remove dust and dry dirt with a soft, damp cloth. ✔✔ Clean grease, oil, paint and ink stains with isopropyl (rubbing alcohol). Immediately rinse with water after removal of stain. ✔✔ Avoid using razor blades or other sharp instruments that might fall and scratch the surface.

11

F I VE YEAR GU AR ANTEE

This unit is warranted to the original purchaser to be free of defects in material and workmanship for five (5) years from the date of purchase. This warranty does not extend to commercial or institutional use or installation. Warranty service should be arranged through the point of purchase. The purchaser is responsible for transporting the unit to and from the point of purchase. Incidental repairs that would involve a minimum of time and effort on behalf of the purchaser will not be considered warranty work and no compensation will be deemed forthcoming. Any failure of the unit that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable items include, but are not limited to: • Change in colour or finish due to chemical usage. •

The use of abrasive cleansers on the acrylic surface.

•

Unit not properly installed in accordance with manufacturers instructions.

•

Damage caused during shipping, handling or installation (eg. Cracks, chips, scratches).

•

Operating, maintenance, safety guidelines not being followed.

•

Any alterations to the unit.

•

Damage to the unit as a result of accidental impact, fire, flood, freezing, normal wear.

•

Scratches, chips, cracks or holes caused due to shipping, storage or installation.

A thorough inspection must be made at time of pick up or delivery. If the unit is damaged a claim must be made with the carrier. Report any damage promptly and prior to installation. Quality Craft Ltd. will not be held liable for any freight damage or damage caused by leaks due to freight damage. Inspection prior to installation is the responsibility of the installer, contractor or

user. Quality Craft Ltd. will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing. Quality Craft Ltd. will not be held liable for damages resulting from the improper fit or installation of products not supplied by this company. Quality Craft Ltd. will not be held liable for loss of use of unit, inconvenience, costs incurred for labour, materials, removal and installation of replacement units or any other incidental or consequential damages. Costs relating to obtaining access for repair or replacement are the responsibility of the user. Under no circumstance shall Quality Craft Ltd. or any of its representatives be held liable for injury to any persons or damage to any property. Quality Craft Ltd. obligations shall be limited to the repair or replacement of a unit (at our option) that may prove, by our sole examination, to be defective under normal use and service during the warranty period. The Company may issue credit in the amount of the invoice value of the defective product (or a percentage of it according to use) in lieu of repair or replacement. All replacements FOB Quality Craft Ltd. nearest service depot. Quality Craft Ltd. warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer’s specifications. This warranty shall not apply to any product that has been subject to accident, alteration, misuse, abnormal chemical conditions. This warranty is made in lieu of all other warranties expressed or implied. No other warranty, expressed or implied, is assumed or will be assumed. Imported by: QUALITY CRAFT KITCHEN AND BATH LTD. 2436 Boul. Industriel Laval, Quebec Canada H7S 2G7 Tel: 1-800-459-4409 www.qualitycraft.com

12