User’s Manual Thermal receipt printer

Contents Contents..................................................... ...........................1 Physical dimension.........................................................................................2

RP-100-300II

Printer features..............................................................................................2 Printer specification.......................................................................................2 Drive installation........................................................................................4 Printer self-test page..................................................................................6 Hexadecimal mode...................................................................................6 Start DHCPfunction.............................................................................6 LAN port connection setting.......................................................................6 Standard TCP/IP port addition.......................................................................9 Baud rate setting........................................................................13 Buttons.....................................................................................................14 Buzzer...................................................................................................15 Interface..................................................................................................13 DIP switch....................................................................................................14 Cutter maintenance....................................................................................15

1

Greek/Hebrew/East Europe/Iran/WPC1252/PC866/PC852/

1. Printer Physical dimension：

PC858/IranII/Latvian/Arabic/PT151,1251/PC73

LxWxH：180x139x127mm；

7/WPC/

Weight：1.23kg；

1257/Thai Vietnam/PC864/PC1001/(Latvian)/(PC1001)/

2. Features:

(PT151,1251)/(WPC1257)/(PC864)/(Vietnam)/(

300mm/sec high print speed;

Thai) UPC-A/UPC-E/JAN13(EAN13)/JAN8(EAN8)C

Low power consumption：1.44w(Min.); Barcode mode

Multiple interface: Serial, USB, Ethernet port

CODABAR/CODE93/CODE128/QRCODE

Automatically resume printing after disconnection; EPSON ESC/POS & Star command compatible

Fonts

GB18030

Data

128K bytes

NV Flash

256K bytes

Buffer

3. Specification：

Printing

Print method

Direct thermal

Print width

72-50mm

Dot density

576-512dot/line

Print speed

300mm/s

Interface

Serial+Ethernet+Parallel

Paper diameter

83mm

Line space

3.75mm (adjustable by software)

Cashdrawer Power

out

AC 110V/220V，50 ~ 60Hz，DC 12V/2.5A

Physical

Weight

1.23kg

properties

Dimension

180*139*127mm

Environment

environment Storage environment

ANK Font Font A: 12×24dots Font B: 9×17dots

DC 24V/1A

Power supply

Work

Character Size

ODE39/ITF/

Auto Cutter

Reliability

Temperature:5-45℃， Humidity:10 ~ 80%

Temperature:-10 ~ 50℃，Humidity:10 ~ 90% 100km

Simplified/Traditional Chinese Character: 24×24dots

Barcode

2

Code page

PC437/Katakana/PC850/PC860/PC863/PC86 5/West Europe/

3

4. Driver installation 1）.Insert the driver CD disk, run the Partner 80Driver to set up

4）Choose the correct port.

2）Choose the system which you used.

5) Completed.

3) Choose the model RP-100-300II

4

5

5. Print self-test page A. Turn off the printer. B. Make sure the paper roll is installed correctly and the printer top cover is closed. C. Press and hold on the FEED button and turn on the printer. When the red indicator is OFF, then release the FEED button. printer will print out a page.

8. LAN port connection setting A. Connect printer to PC via LAN cable. Please make sure PC’s IP should be on the same network segment with the printer’s IP . For example: Printer default IP address：192.168.123.100. So PC’s IP address should be set 192.168.123.* network segment, but can not the same as the printer IP, otherwise printer will not be connected with the PC.

6. Hexadecimal mode A. Turn off the printer. B. Make sure the paper roll is installed correctly and the printer top cover is closed. C. Press and hold on the FEED button and turn on the printer. After 10 seconds, please release the FEED button, then printer will be entered the Hexadecimal mode. 7. Start the DHCP function A. Set from web browser. 1) Open the web browser through IP address shown on the self-test page. 2) Click “ DHCP Client, set the time of getting the IP (shortest is 14s) 3) Click “save” and then “Reboot”. 4) Print the self-test page with new IP address. If the printer can’t get the new IP successfully, it will print out the previous IP.

B. Connect with server Make sure the printer and PC are in the same segment, if not, please revise the printer’s IP as below method: 6

7

1) With Windows software utility tool.

9. Standard TCP/IP port addition Connect the printer with PC through Ethernet port. Install the printer. 1) Right click the printer, and choose the printer properties.

2) Configure using the web browser. Open the web browser through IP address showed on the self-test page. Click “Configure Interface”, put in the new IP address, Subnet mask and Gateway address. Then save and reboot. When the two red indicators light, showed the setting is successfully.

8

9

2) Create a new port

10

11

10. Baud rate setting Using serial port to print, printer serial baud rate must be same as the PC serial port baud rate, otherwise the printer won’t work. The setting method is as follows: A. Printer Baud rate ：Set the DIP switch on the bottom of the printer (SW7 , SW8Combination).

DIP SWITCH

3) Choose the new port.

SW7 SW8 Baud rate

ON ON 38400

OFF ON 115200

ON OFF 9600

OFF OFF 19200

Baudrate table

B. PC serial baud rate: Please install the printer driver first, then goto “Printer properties” to adjust the baud rate on the PC.

12

13

11. Buttons 1) Feed Button：A. Paper feed B. Print self-test page C. enter Hexadecimal mode 2) Power indicator (Blue): When the power indicator is ON, Printer is powered on. 3) Error indicator (Red): A. flashing slowly 2 time: Cutter error B. Flash fast: Printer overhead protection is activated C. Error indicator is ON: Paper shortage; 4) Paper shortage indicator (Red): Paper shortage indicator lights: Paper sensor error or close cover sensor error or Paper shortage 12. Buzzer 1) When cutter error occurred, buzzer will sound short beep 2 times, and then follow by a long beep 1 time. 2) When paper shortage or cover is not closed, buzzer will sound continuously short beep sound. 3) When printer resumes printing from un-printed data in buffer memory, buzzer will quickly sound 4 times after receipt printed. 13. Interface

USB 2.0

100M Ethernet RS232 Serial

14

Pin2/pin5Ca sh drawer port

DC24V power

15

14. DIP Switch

1

ON OFF

2

3

4

Sele ct cutt er

Select beeper

SELECT PRINT DENSITY

Two-byte character code

OFF

ON

Dark

ON

ON

OFF

Light

OFF

5 Character per line 42-font A /56-font B 48-font A /64-font B

6

7

8

Cutter with Select cash baudrate drawer Yes No

15. Auto Cutter Maintenance Improper usage and/or bad quality thermal paper may cause the cutter jam (stuck), thus printer cover is unable to open. In this case, you may power cycle the power button (turn off and turn back on after 3 seconds) and check if the auto cutter has recover itself from cutter jam by trying to open the printer lid. If print lid still can’t be opened, please follow below manual method to restore the cutter back into position. 1st: Open the printer front cover, and then start to turn the gear until the cutter knife has returned fully. Once it has cutter knife has returned fully, you can open the printer lid.

16

Turn the gear to reset the cutter Open cover by the arrow direction

Caution: Do not open the printer cover by force, doing so will result in damaging the print head and auto cutter.

17