User’s Guide
November 2003
Audio Converter Products, Digital Audio SLEU038
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments Post Office Box 655303, Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product incorporating the goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may not meet the technical requirements of the directive. Should this evaluation kit not meet the specifications indicated in the EVM User’s Guide, the kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods. Please be aware that the products received may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). Due to the open construction of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Please read the EVM User’s Guide and, specifically, the EVM Warnings and Restrictions notice in the EVM User’s Guide prior to handling the product. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact the TI application engineer. Persons handling the product must have electronics training and observe good laboratory practice standards. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which such TI products or services might be or are used.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of ±15 V and the output voltage range of ±15 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM. Please consult the EVM User’s Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than 55°C. The EVM is designed to operate properly with certain components above 55°C as long as the input and output ranges are maintained. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified using the EVM schematic located in the EVM User’s Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated
Preface
About This Manual This user’s guide provides information needed by a technician for the operation and maintenance of the DEM-PCM/DSD1791/1793 evaluation module (EVM). This includes descriptions of connections, controls, audio interface selection, control via software and I2C, parts listings, board layouts, and schematic diagrams.
How to Use This Manual This document contains the following chapters: Chapter 1—Description Chapter 2—Schematics and Printed-Circuit Boards
Related Documentation From Texas Instruments DSD1791 24-Bit, 192-kHz Sampling, Advanced Segment, Audio Stereo Digital-to-Analog Converter data sheet, SLES072 DSD1793 24-Bit, 192-kHz Sampling, Advanced Segment, Audio Stereo Digital-to-Analog Converter data sheet, SLES075 PCM1791A 24-Bit, 192-kHz Sampling, Advanced Segment, Audio Stereo Digital-to-Analog Converter data sheet, SLES071 PCM1793 24-Bit, 192-kHz Sampling, Advanced Segment, Audio Stereo Digital-to-Analog Converter data sheet, SLES076
FCC Warning This equipment is intended for use in a laboratory test environment only. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference.
v
Contents
Trademarks Microsoft is a trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation. Other trademarks are the property of their respective owners.
vi
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Operating Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.1 SW001, SW002, SW003 DAI PCM Interface Format . . . . . . . . . . . . . . . . . . . . . 1.3.2 SW004 Reset for DAI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.3 SW005 DAI/External Interface Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.4 JP001 BCK Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.5 SW006 Operation Control for DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.6 SW001 on Daughter Card − Operation Control for PCM1793 . . . . . . . . . . . . . . 1.4 Audio Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.1 PCM Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.2 DSD Audio Interface for PCM1791/1793 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4.3 DSD Audio Interface for DSD1791/1793 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 Demonstration Software Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 I2C Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 Demonstration Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 DEM/DSD1791/1793 Parts List (BOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 DEM-AS/VDAC Board Section Parts List (BOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1 1-2 1-2 1-3 1-3 1-3 1-3 1-3 1-3 1-3 1-4 1-5 1-5 1-5 1-5 1-5 1-6 1-8 1-9
2
Schematics and Printed-Circuit Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.1 DEM-DAI/ASDAC Printed-Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.2 DEM-AS/VDAC Printed-Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 2.3 DEM-DAI/ASDAC Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 2.4 DEM-AS/VDAC Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
vii
Contents
1−1. 2−1. 2−2. 2−3. 2−4. 2−5. 2−6. 2−7. 2−8. 2−9. 2−10. 2−11.
DEM−PCM/DSD1791/1793 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 DEM-DAI/ASDAC Silkscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 DEM-DAI/ASDAC—Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 DEM-DAI/ASDAC—Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 DEM-AS/VDAC Silkscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 DEM-AS/VDAC—Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 DEM-AS/VDAC—Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 DEM-DAI/ASDAC Analog Section (Sockets for Daughter Board, Low-Pass Filter) . . . . . 2-7 DEM-DAI/ASDAC Regulator and Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 DEM-DAI/ASDAC—PCM/DSD1791, PCM1793 Digital Section (Digital Audio Interface) 2-8 DEM-DAI/ASDAC—PCM1793 Digital Section (Digital Audio Interface) . . . . . . . . . . . . . . . 2-9 DEM-AS/VDAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
1−1. 1−2. 1−3.
viii
SW001/002/003: For S8414 (DAI Receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Audio Interface Format Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 De-emphasis Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Chapter 1
The DEM-PCM/DSD1791/1793 is an evaluation module for the 192-kHz, 24-bit stereo differential voltage output DAC PCM/DSD1791/1793 family. - DEM-PCM1791: PCM1791A. Software control - DEM-PCM1793: PCM1793. Hardware control - DEM-DSD1791: DSD1791. Software control - DEM-DSD1793: DSD1793. I2C control
Topic
Page
1.1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.3
Operation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.4
Audio Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.5
Demonstration Software Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.6
I2C Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.7
Demonstration Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.8
DEM/DSD1791/1793 Parts List (BOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.9
DEM-AS/VDAC Board Section Parts List (BOM) . . . . . . . . . . . . . . . . . . 1-9
Description
1-1
Block Diagram
1.1 Block Diagram Figure 1−1. DEM−PCM/DSD1791/1793 Block Diagram DEM-AS/VDAC Daughter Card SW001
SW001~SW004 MODE Control
CN003 Register Control
MODE Control
S/PDIF COAX IN
S/PDIF OPT IN
DAC PCM1791 PCM1793 DSD1791 DSD1793
Logic Interface CN001
DAI CS8414
BAL Amp with LPF 5534
Lch OUT
BAL Amp with LPF 5534
Rch OUT
3.3 V REG CN058
DGND
+5 V Digital
+5 V AGND Analog
–15 V
AGND
+15 V
1.2 Connections The DEM-PCM/DSD1791/1793 can be operated by connecting ±15-V and 5-V power supplies and the S/PDIF interface. - CN051 AVCC
: 9 V to 15 V
Icc = 20 mA, typical
- CN053 AVCC−
: –9 V to –15 V
Icc = 20 mA, typical
- CN054 VCC
: 4.5 V to 5.5 V
Icc = 80 mA, typical (CN058 shorted, default)
- CN052 GND (analog)
- CN055 GND (analog) - CN056 VCC
: 4.5 V to 5.5 V
- CN057 GND (digital) - CN001 RCA jack
: S/PDIF coax input
- U001 TORX
: S/PDIF optical input
The S/PDIF interface accepts up to fs = 96 kHz sampling rate, fs = 192 kHz, 24-bit PCM data and 64 fs, 1-bit DSD data can be connected directly on interface connector. A stereo audio signal can be obtained by connecting RCA audio cables to the onboard RCA stereo jacks, CN103 and CN104.
1-2
Operating Controls - CN103: L-channel audio out (2.1 V rms) - CN104: R-channel audio out (2.1 V rms)
1.3 Operating Controls 1.3.1
SW001, SW002, SW003 DAI PCM Interface Format These switches select the PCM audio interface format for the S8414 DAI receiver, and the interface formats are listed in Table 1−1. The default interface format is 16- to 24-bit I2S.
Table 1−1. SW001/002/003: For S8414 (DAI Receiver)
1.3.2
SW001
SW002
SW003
Receiver Output Data Format
L
L
L
16- to 24-bit left-justified
L
H
L
16- to 24-bit l2S
H
L
H
16-bit right-justified (or standard)
L
H
H
18-bit right-justified (or standard)
SW004 Reset for DAI Switch SW004 is the reset control for the CS8414 DAI receiver.
1.3.3
SW005 DAI/External Interface Selection Switch SW005 selects whether the S/PDIF inputs for the PCM/DSD1791/1793 are provided through the CS8414 DAI receiver or supplied as external data. - INT:
S/PDIF, DAI receiver data (default)
- EXT: External data
1.3.4
JP001 BCK Selection Jumper JP001 selects the BCK clock format for the CS8414. - IIS:
I2S right-justified (default)
- 24L/J: 24-bit left-justified
1.3.5
SW006 Operation Control for DAC Switch SW006 is the register reset control for the PCM1791 and DSD1791. For normal board operation, all four switches must be set to H. - RESET: H / normal operation (default) - RESET: L / reset operation
1.3.6
SW001 on Daughter Card − Operation Control for PCM1793 SW001 on the daughter card is the operation control for the PCM1793 hardware model.
Description
1-3
Audio Data Interface
Table 1−2. Audio Interface Format Selection FMT2 PIN 28
FMT1 PIN 27
FMT0 PIN 26
L
L
L
16-bit standard format, right-justified
L
L
H
20-bit standard format, right-justified
L
H
L
24-bit standard format, right-justified
L
H
H
24-bit MSB-first, left-justified format
H
L
L
16-bit l2S format
H
L
H
24-bit l2S format
H
H
L
Reserved
H
H
H
Reserved
FORMAT
Switches FMT0, FMT1, and FMT2 select the audio interface format for the PCM1793. The interface formats are listed in Table 1−2.
Table 1−3. De-Emphasis Control DEMP1 PIN 25
DEMP0 PIN 24
L
L
Disabled
L
H
48 kHz
H
L
44.1 kHz
H
H
32 kHz
De-Emphasis Function
Switches DEMP0 and DEMP1 select the sampling frequency for which de-emphasis filtering is performed. The available frequencies are listed in Table 1−3.
1.4 Audio Data Interface CN001 on the daughter card selects the data interface. Available choices are DSD by device type and PCM. The default setting is for the PCM audio data interface with S/PDIF. The DSD interface can also be connected directly to this connector. P-SCLK
1-4
DBCK
MUTE
DSD-R
P-DATA
DSD-L
P-BCK
(DSD)
P-LRCK
(DSD)
Demonstration Software Control
1.4.1
1.4.2
1.4.3
PCM Audio Interface P-SCLK:
SYSTEM CLOCK
P-DATA:
DATA clock
P-BCK:
BCK clock
P-LRCK:
LRCK clock
DSD Audio Interface for PCM1791/1793 P-SCLK:
DSD BCK clock
P-LRCK:
DSD DATA-R
P-DATA:
DSD DATA-L
P-BCK:
GND
MUTE:
GND
DSD Audio Interface for DSD1791/1793 P-LRCK:
GND
P-BCK:
GND
P-DATA:
GND
DBCK:
DSD BCK clock
DSD-L:
DSD DATA-L
DSD-R:
DSD DATA-R
1.5 Demonstration Software Control Software provided with the DEM-PCM/DSD1791 allows programming of the PCM/DSD1791 internal registers. The software operates on computers running Microsoft Windows 3.1, 95, 98 or 2000. The demonstration software requires connection of the PC printer port to CN003 of the demo board using a standard printer port cable. After installing and executing the demo software, the main window shows register bit codes and the sub-window shows register control function.
1.6 I2C Control The DSD1793 has an I2C control function. The I2C interface is provided on 5-pin connector RA001, shown in the following diagram. NC
ADR0 SCL
SDA ADR1
Description
1-5
Demonstration Software
1.7 Demonstration Software Demonstration software is provided to control the PCM1791/DSD1791’s internal register using a PC running Microsoft Windows. The software requires the use of a printer cable to connect between the PC and connector CN003 of the DEM-PCM/DSD1791. The demonstration software includes a total five files in the DEM1791; these files include the following: DEM1791.exe DEM1791.ini Vbrjp200.dll Ver.dll Inpout.dll Copy these files to a convenient directory (folder) such as C: DEM1791 Then change the printer-port address in DEM1791.ini to: &H378, &H278, or &H3BCO (Most PCs use &H378 as the default printer port address.)
1-6
Demonstration Software
Top Menu
Attenuation Window
Operation Window
Function Window
Description
1-7
DEM/DSD1791/1793 Parts List (BOM)
1.8 DEM/DSD1791/1793 Parts List (BOM) Reference No.
Value
Part Type
Part Number
Manufacturer
C001, C002
0.01 µF
Film capacitor
AMFF0050J103
Nissei
C004, C006, C008, (C016), C051, C058
0.1 µF
Film capacitor
AMFF0050J104
Nissei
C009
0.068 µF
Film capacitor
AMFF0050J683
Nissei
C010, C011, C013, C014, C055
0.1 µF
Ceramic capacitor
RPE132F104Z50
Murata
C003, C005, C007, C109, C110, C111, C112
10 µF/16 V
Ceramic capacitor
ROA-16V100M
ELNA
(C015), 052, 053, 054, 057
100 µF/16 V
Ceramic capacitor
ROA-16V101M
ELNA
C101, C102, (C017), (C018)
10 µF/16 V
Ceramic capacitor
R3A-16V100M
ELNA
C105, C106, C107, C108
2700pF
Film capacitor
APSF0100J272
Nissei
C012
10 µF/16 V
Ceramic capacitor
SME16VB10M
Nikkemi
C056
10 µF/16 V
Tantalum capacitor
DN1C100M1S
NEC
CN003
L connector
57LE40360-7700(D3)
Daiichi Denshi
CN002, CN058, JP002
2-pin connector
FFC-2BMEP1
Honda
CN104
RCA (Red)
LPR6520-0802
SMK
CN103
RCA (Yellow)
LPR6520-0803
SMK
CN001
RCA (Yellow)
LPR6520-0804
SMK
CN051
Banana jack (Orange)
T-45 (Yellow)
Sato Parts
CN052
Banana jack (Green)
T-45 (Green)
Sato Parts
CN053
Banana jack (Blue)
T-45 (Blue)
Sato Parts
CN054, CN056
Banana jack (Red)
T-45 (Red)
Sato Parts
CN055, CN057
Banana jack (Black)
T-45 (Black)
Sato Parts
CN101, CN102, (CN006), (CN007)
C-T connector
XB-3-7-20
MAC8
D001
Diode
1SS133
ROHM
JP001
4-pin connector
FFC-4BMEP1
Honda
R001
75 Ω
Resistor
SN14C2C-75ΩF
KOA
R003
47 kΩ
Resistor
SN14C2C-47kΩF
KOA
R002, R004
470 Ω
Resistor
SN14C2C-470ΩF
KOA
R101−104, R109−112
360 Ω
Resistor
SN14C2C-360ΩF
KOA
R105−108
Resistor
R113, R114
100 Ω
Resistor
SN14C2C-100ΩF
KOA
RA001
47k Ω × 5
Resistor Array
M6-1-473J
BI
5-pin connector
FFC-5AMEP1
Honda
RA001 RA001
Resistor
SN14C2C-4.7kΩF
KOA
U001
TOSLINK
TORX179P
Toshiba
U002
Digital audio I/F receiver IC
CS8414-CS
Cirrus Logic
U003
Logic IC
TC74VHC14F
Toshiba
U004
Logic IC
TC74HCT32AF
Toshiba
U005, U006
Logic IC
TC74VHC244F
Toshiba
U051
Regulator IC
REG1117-3.3
Burr-Brown
1-8
4.7 kΩ
DEM-AS/VDAC Board Section Parts List (BOM) Reference No.
Value
Part Type
Part Number
Manufacturer
U101, U102
IC socket DIP 8-pin
100-008-000
3M
SW001, SW002, SW003
DIP switch
FT1D-2M
Fujisoku
SW004
Push SE
FP1D-2M
Fujisoku
SW005
DIP SW-2
FT2D-2M
Fujisoku
SW006
DIP SW-4
DSS104
Fujisoku
JP101−103
1.9 DEM-AS/VDAC Board Section Parts List (BOM) Reference No.
Value
Parts Type
Parts Name
Manufacturer
C001, C003, C005
10 µF/16 V
AL ELE capacitor
ROA-16V-100M
ELNA
C002
0.1 µF
Ceramic capacitor
RPE132F104Z50
Murata
C004, (C006)
0.1 µF/2125
Ceramic capacitor
GRM40F104Z25PT
Murata
(C007), (C008)
3900 pF
Film capacitor
APSF0100J392
Nissei
R001, R002, R003, R004
1 kΩ
Resistor
SN14C2C-1kΩF
KOA
R005
47 kΩ
Resistor
SN14C2C-47kΩF
KOA
RA001
47 kΩ × 5
Resistor array
M6-1-473J
Beckman
DIP SW, 5-contact
DSS105
Fujisoku
SW001 CN001
5 pins × 3
15-pin connector
FFC-15NSM1
Honda
CN002
3 pins
3-pin connector
FFC-3AMEP1
Honda
U001
28-pin SSOP
DSD1791
Burr-Brown
U001
28-pin SSOP
PCM1791
Burr-Brown
U001
28-pin SSOP
DSD1793
Burr-Brown
U001
28-pin SSOP
PCM1793
Burr-Brown
Description
1-9
1-10
Chapter 2
This chapter presents the DEM-DAI/ASDAC and the DEM-AS/VDAC printedcircuit boards and schematics
Topic
Page
2.1
DEM-DAI/ASDAC Printed-Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2
DEM-AS/VDAC Printed-Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.3
DEM-DAI/ASDAC Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.4
DEM-AS/VDAC Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Schematics and Printed-Circuit Boards
2-1
DEM-DAI/ASDAC Printed-Circuit Board
2.1 DEM-DAI/ASDAC Printed-Circuit Board Figure 2−1. DEM-DAI/ASDAC Silkscreen
2-2
DEM-DAI/ASDAC Printed-Circuit Board
Figure 2−2. DEM-DAI/ASDAC—Top View
Schematics and Printed-Circuit Boards
2-3
DEM-DAI/ASDAC Printed-Circuit Board
Figure 2−3. DEM-DAI/ASDAC—Bottom View
2-4
DEM-AS/VDAC Printed-Circuit Board
2.2 DEM-AS/VDAC Printed-Circuit Board Figure 2−4. DEM-AS/VDAC Silkscreen
Figure 2−5. DEM-AS/VDAC—Top View
Schematics and Printed-Circuit Boards
2-5
DEM-AS/VDAC Printed-Circuit Board
Figure 2−6. DEM-AS/VDAC—Bottom View
2-6
DEM-DAI/ASDAC Schematic
2.3 DEM-DAI/ASDAC Schematic Figure 2−7. DEM-DAI/ASDAC Analog Section (Sockets for Daughter Board, Low-Pass Filter) R109
3.3k C105
VDD
VCC1
R101
R105 680
1.8k (NC)
VCC
MUTE
VCC
VDD
GND
C101
VDD
GND
10uF/16V
GND
(NC)
C102
GND
(NC)
10uF/16V
RST-
RESET-
(NC)
MDO
MDO
MDI
MDI
VOUTL−
MC
MC
VOUTL+
ML
ML
GND
AGND
GND
AGND
2
/16V R113 100 C111
R107
R103 1.8k R111 3.3k
CN103 RCA pj
6 4
680
C107
10uF/16V AVCC-
560pF
AVCC− R110
3.3k
AVCC+ C106
VOUTR−
CLKO
CLKO/D_BCK VOUTR+
R102
R106
SCLK
P_SCLK
(NC)
1.8k
680
DSD_R
AVCC−
P_BCK
AVCC+
LRCK
P_LRCK
(NC)
DATA
P_DATA
GND
2
C110 10uF
7
/16V R114 100 C112
680 C108
3.3k
CN104 RCA pj
6
R108
1.8k R112
CN102 XB-3-7-20
CN101 XB-3-7-20
AVCC+
4
R104
GND
DSD_L
560pF
U102 NJM5534 3
C104 1800pF
D-SCLK D-BCK
7
U101 NJM5534 3
C103 1800pF
C109 10uF
(NC)
D_SCLK
BCK
560pF AVCC+
10uF/16V AVCC-
560pF
DSD-R DSD-L
Figure 2−8. DEM-DAI/ASDAC Regulator and Connector CN056 Banana Jack (Red) CN057 Banana Jack (Black)
CN054 Banana Jack (Red)
VCC2
VCC1
CN055 Banana Jack (Black)
CN058
CN052 Banana Jack (Gray)
CN053 Banana Jack (Blue)
CN051 Banana Jack (Orange)
VDD U051 REG1117-3.3 2
C056 10uF /16V
C058 0.1uF C057 100uF /16V
OUT IN GND 1
AVCC+
3
C055 0.1uF
C053 100uF /16V
C051 0.1uF
C054 100uF /16V
AVCC−
C052 100uF /16V
Schematics and Printed-Circuit Boards
2-7
DEM-DAI/ASDAC Schematic
Figure 2−9. DEM-DAI/ASDAC—PCM/DSD1791, PCM1793 Digital Section (Digital Audio Interface) 1
18
VDD
CN003 57LE-40360-7700(D3) 36
19
C014 U006 74VHC244
SW006 DSS104
0.1uF
1
Vcc
20
1
[RST-]
2
19
2
[MDO]
3
18
3
[MDI]
4
17
5
16
6
15
7
14
8
13
4 [MC]
[ML]
RA001 47k x5
9
RSTMDO MDI MC ML
12
VCC2 10
11
GND
CN007 XB-3-7-20 U002
C011
CN002 FFC-2BMEP1 1
C008 10uF /16V
(L001)
VERF
C 2 Cd/F1
Ce/F2
Cc/F0
SDATA
3 4 C005 10uF /16V
C006 0.1uF
Cb/E2
ERF
Ca/E1
M1
C0/E0
M0
5 6
3
7 VD+ 8 DGND C002
1
0.01uF
CS8414
U001 TORX173 (TORX179P)
VA+ AGND
9 RXP
FILT
RXN
MCK
10 2
4
5
6
C003 10uF /16V
11 C001 0.01uF
FSYNC
M2
SCK
M3
12 13
C004 0.1uF
CS12/FCK
SEL
U
CBL
14
U004
28 1
26
2
13
25
3
12
24 23 C008 0.1uF
22
4
11
5
10
10uF /16V
6
47k R004 470
9 C012 10uF /16V
8
7
21
GND
SW004 FP1F-2M
20 19 18 C010 17
R002 470
U003
0.1uF 74VHC14
16 1 Vcc
15
INT(CS8414) SW005 FT2D-2M C013
Vcc
R003
14
C007
DAI select
R001 75
D001 1SS133
27
C009 0.068uF
CN001 RCA pj
0.1uF 74HCT32
0.1uF
14
2
13
3
12
4
11
5
10
6
9
7
8 GND
1 EXT
[e-SCLK]
[SCLK] [e-BCK] [BCK] [e-LRCK] [LRCK] [e-DATA] [DATA]
Vcc
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
GND
[BCK]
20
[SCLK]
C017 10uF /16V
[BCK] SW001 FT1D-2M
SW002 FT1D-2M
SW003 FT1D-2M
CN006 XB-3-7-20
[LRCK]
[SCLK] [DATA]
JP001 FFC-4BMEP1
JP002 FFC-2BMEP1 AGND
[BCK]
11
[BCK(INV)]
U005 74VHC244
[LRCK] [DATA]
SCLK BCK
(FIL001) 3 IN
OUT 2
1
LRCK DATA (C015) 100uF/16V
DSD-L
[e-DATA]
[e-LRCK]
[e-BCK]
[e-SCLK]
GND 1
(C016) 0.1uF
DSD-R D-BCK D-SCLK
24 (CN004) FFC-48BMEP1
25
2-8
48
DEM-DAI/ASDAC Schematic
Figure 2−10. DEM-DAI/ASDAC—DSD1793 Digital Section (Digital Audio Interface) 1
18
VDD
CN003 57LE-40360-7700(D3) 36
19
(C014) (U006) 1
(SW006)
Vcc
20
1
[RST-]
2
19
2
[MDO]
3
18
3
[MDI]
4
17
5
16
6
15
7
14
8
13
4 [MC]
[ML]
(RA001)
9
RSTMDO MDI MC ML
12
VCC2 10
11
GND
CN007 XB-3-7-20 U002
C011
CN002 FFC-2BMEP1 1
C008 10uF /16V
(L001)
VERF
C 2 Cd/F1
Ce/F2
Cc/F0
SDATA
Cb/E2
ERF
3 4 C005 10uF /16V
C006 0.1uF
5
M1
Ca/E1 6
M0
C0/E0 3
7 VD+ 8 DGND C002
1
0.01uF
CS8414
U001 TORX173 (TORX179P)
VA+ AGND
9 RXP
FILT
RXN
MCK
10 2
4
5
6
C003 10uF /16V
11 C001 0.01uF
FSYNC
M2
SCK
M3
12 13
C004 0.1uF
CS12/FCK
SEL
U
CBL
14
U004
28 1
26
2
13
25
3
12
24
4
11
C007
5
10
10uF /16V
6
9
23 C008 0.1uF
22
R003
14
47k R004 470
C012 10uF /16V
8 GND
SW004 FP1F-2M
20 19 18 C010 17
R002 470
U003
0.1uF 74VHC14
16 1 Vcc
15
INT(CS8414) SW005 FT2D-2M C013
Vcc
7
21
DAI select
R001 75
D001 1SS133
27
C009 0.068uF
CN001 RCA pj
0.1uF 74HCT32
13
3
12
4
11
5
10
6
0.1uF
14
2
9
7
8 GND
1 EXT
[e-SCLK]
[SCLK] [e-BCK] [BCK] [e-LRCK] [LRCK] [e-DATA] [DATA]
Vcc
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
GND
[BCK]
20
2
[SCLK]
C017 10uF /16V
[BCK] SW001 FT1D-2M
SW002 FT1D-2M
SW003 FT1D-2M
CN006 XB-3-7-20
[LRCK]
[SCLK] [DATA]
JP001
JP002 FFC-2BMEP1
FFC-4BMEP1
AGND
[BCK]
11
[BCK(INV)]
U005 74VHC244
[LRCK] [DATA]
SCLK BCK
(FIL001) 3 IN
OUT 2
1
LRCK DATA (C015) 100uF/16V
DSD-L
[e-DATA]
[e-LRCK]
[e-BCK]
[e-SCLK]
GND 1
(C016) 0.1uF
DSD-R D-BCK D-SCLK
24 (CN004) FFC-48BMEP1
25
48
Schematics and Printed-Circuit Boards
2-9
DEM-AS/VDAC Schematic
2.4 DEM-AS/VDAC Schematic Figure 2−11. DEM-AS/VDAC VDD
(NC) MUTE VDD VDD
R005 47k
CN001 FFC-15NSM1 #1 Pin (DSD)
GND
#2 Pin (DSD)
GND
#3 Pin DSDL
RESET-
#4 Pin DSDR
MDO
#5 Pin DBCK
U001 PCM1791/93 P_LRCK
1
P_BCK
2
P_DATA
3
MUTE
4
P_SCLK
5
MDI MC
C002 0.1uF 7
ML
8
AGND D_SCLK CLKO/D_BCK
9 C001 10uF/16V
P_SCLK
13
P_BCK P_DATA DSD_L
11 12
DSD_R P_LRCK
10
14 C003 10uF /16V
MS-/FMT2
BCK
MC/FMT1
DATA/DDL
MDI/FMT0
MUTE/DDR MDO/DEMP1 SCKI/DBCK SCKO/DEMP0
RSTVDD DGND AGNDF
PCM1791/93
6
LRCK
ZEROL ZEROR VCCF VCCL
VCCR
AGNDL
AGNDR
VOUTL-
VOUTR-
VOUTL+
VOUTR+
AGNDC
VCOM
VCCC
28
RA001 47k x 5
27
1
FMT2
2
FMT1
3
FMT0
4
DEMP1
5
DEMP0 VCC
SW001 DSS105
VCC VCC
26 25 24 23 22
CN002 FFC-3AMEP1 SCKO ZERO-L ZERO-R
19
VOUTLC007 3900pF
R003 1k
GND GND VOUTR-
R001 1k
VOUTR+ (NC)
R004 1k C004 0.1uF
(NC)
VOUTL+ R002 1k
16 15
(NC)
(NC)
C005 10uF/16V
18 17
GND
(NC)
21 C006 0.1uF 20
GND
C008 3900pF
AVCCAVCC+ (NC) GND GND
2-10