Spiral plastic tubing
Spiral plastic tubing Product range overview
Spiral tubing, pre-assembled PUN-SG Polyurethane PPS Polyamide
2
Water (not drinking water)
PUN-S-DUO Polyurethane Paired tubing
Vacuum
PUN-S Polyurethane
Operating medium
Compressed air
[mm] Spiral tubing
Colour
Blue/black
j
Black
Type
Blue
Version
n
n
–
n
n
–
–
–
n
n
n
–
n
–
–
n
n
n
n
–
–
n
n
n
O.D. 4, 6, 8, 10, 12
4, 6, 8, 10, 12
I.D. 6.4; 7.9
4.75; 6.35
è Internet: www.festo.com/catalogue/...
Subject to change – 2015/11
Spiral plastic tubing Product range overview è Page/ Internet
Microbes
n
–
–
++1)
+
++
n
n
n
n
–
–
+
+
+
n
n
–
–
+
++
+
++
+
n
n
n
–
+
++
+
+
+
Spiral tubing PUN-S
PUN-S-DUO
Spiral tubing, pre-assembled PUN-SG
PPS
++ + 1) 2)
Shore hardness2)
Chemicals
n
Stress cracks
Approved by the German Technical Control Board (TÜV)
n
Hydrolysis
Suitable for use with energy chains
n
UV radiation
PWIS-free to FN 942 010
Resistance
Halogen-free
Type
D 52 _3
6
D 52 _3
8
A 87 _3
10
–
11
Highly suitable Limited suitability (on request) Not suitable Applies to black colour Values are determined using test boards. Values determined using tubing may vary.
2015/11 – Subject to change
è Internet: www.festo.com/catalogue/...
3
Spiral plastic tubing Technical data Method of measurement Flow-relevant bending radius Rd The tube is bent in the direction of its own curve until the tubing outer diameter is flattened by 5%. Rd is then calculated mathematically. The flow rate is not reduced until Rd is reached.
Cross section flattened by bending the tube. d = non-deformed tubing O.D. d1 = deformed tubing O.D.
Minimum bending radius Rmin The tube fixed to the base plate is bent until the deformation results in a kink. The measured value is the minimum bending radius Rmin. This Rmin results in significant reductions in flow rate.
Length specifications Working length
Block length
4
è Internet: www.festo.com/catalogue/...
With tensile load, 80% of the maximum section length
Without tensile load
-H-
Note
The working length represents 80% of the maximum permissible expan sion. This maximum expansion is the limit value before permanent deformation takes place.
Subject to change – 2015/11
Spiral plastic tubing Type codes Type codes spiral plastic tubing PUN PUN
—
PPS
—
6x1
—
S
—
1
—
DUO
—
BS
—
Material PUN
Polyurethane
O.D. x wall thickness [mm] Design S SG
Spiral Spiral with fabric
Working length [m] Number of tubes DUO
Single tube Paired tubing (only for S)
Colour BK BL BS
Black (only for S) Blue Blue/black (only for DUO)
Pneumatic connection (only for SG) ¼ y
Male thread G¼ Male thread Gy
Type codes spiral plastic tubing PPS 4
–
15
—
¼
—
BL
Material PPS
Polyamide
I.D. [mm] 4 6
I.D. 4.7 mm I.D. 6.2 mm
Working length [m] 7.5 15
Working length 7.5 m Working length 15 m
Pneumatic connection ¼
Male thread G¼
Colour BL
Blue
2015/11 – Subject to change
è Internet: www.festo.com/catalogue/...
5
Spiral plastic tubing PUN-S Technical data Spiral plastic tubing PUN-S Highly flexible plastic tubing.
General technical data Type Pneumatic connection
PUN-4x0,75-S
PUN-6x1-S
PUN-8x1,25-S
PUN-10x1,5-S
PUN-12x2-S
For push-in connector O.D. 4 mm For barbed connector I.D. 3 mm with union nut For barbed connector I.D. 3 mm
For push-in connector O.D. 6 mm For barbed connector I.D. 4 mm with union nut For barbed connector I.D. 4 mm
For push-in connector O.D. 8 mm For barbed connector I.D. 6 mm with union nut For barbed connector I.D. 6 mm
For push-in connector O.D. 10 mm –
For push-in connector O.D. 12 mm –
–
–
Operating and environmental conditions [bar]
–0.95 … +10 è graph
[°C]
Compressed air to ISO 8573-1:2010 [7:–:–] –35 … +60 German Technical Control Board (TÜV)
Operating pressure p as a function of temperature t
Possible fittings
p [bar]
Temperature-dependent operating pressure Operating medium Ambient temperature Approval
Push-in fitting QS, Quick Star1) è Internet: qs
Push-in fitting QS-B, Quick Star1) è Internet: qs-b
Push-in fitting CRQS, Quick Star, stainless steel è Internet: crqs
Push-in fitting NPQM è Internet: npqm
Quick connector CK è Internet: ck
Barbed fitting CN è Internet: cn
t [°C]
1)
Recommended fitting
-H-
Note
Greater force is required when assembling the fittings CK/CN. Expanding the tube ends using a tapered mandrel makes pushing them on easier.
6
è Internet: www.festo.com/catalogue/...
Subject to change – 2015/11
Spiral plastic tubing PUN-S Technical data Materials D 52 _3 TPE-U(PU) RoHS-compliant Free of copper and PTFE
Shore hardness Tube Note on materials
Dimensions and ordering data O.D. I.D. Winding [mm]
[mm]
[mm]
4
2.6
25
6
8
10
12
4
5.7
7
8
2015/11 – Subject to change
46
60
80
95
Number of windings
Working length [m]
Block length [m]
Weight
20
0.5
0.184
13
45
1
0.284
27
70
1.5
0.384
42
23
1
0.344
51
52
2
0.518
110
168
6
1.214
350
12
1
0.304
65
27
2
0.424
140
87
6
0.904
440
9.5
1
0.305
110
22
2
0.43
250
70
6
0.91
760
9
1
0.32
200
20
2
0.452
420
64
6
0.98
1300
Colour
Part No.
Type
Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black
197587 197602 197588 197603 197589 197604 197590 197605 197591 197606 197592 197607 197593 197608 197594 197609 197595 197610 197596 197611 197597 197612 197598 197613 197599 197614 197600 197615 197601 197616
PUN-4x0,75-S-0,5-BL PUN-4x0,75-S-0,5-SW PUN-4x0,75-S-1-BL PUN-4x0,75-S-1-SW PUN-4x0,75-S-1,5-BL PUN-4x0,75-S-1,5-SW PUN-6x1-S-1-BL PUN-6x1-S-1-SW PUN-6x1-S-2-BL PUN-6x1-S-2-SW PUN-6x1-S-6-BL PUN-6x1-S-6-SW PUN-8x1,25-S-1-BL PUN-8x1,25-S-1-SW PUN-8x1,25-S-2-BL PUN-8x1,25-S-2-SW PUN-8x1,25-S-6-BL PUN-8x1,25-S-6-SW PUN-10x1,5-S-1-BL PUN-10x1,5-S-1-SW PUN-10x1,5-S-2-BL PUN-10x1,5-S-2-SW PUN-10x1,5-S-6-BL PUN-10x1,5-S-6-SW PUN-12x2-S-1-BL PUN-12x2-S-1-SW PUN-12x2-S-2-BL PUN-12x2-S-2-SW PUN-12x2-S-6-BL PUN-12x2-S-6-SW
[g]
è Internet: www.festo.com/catalogue/...
7
Spiral plastic tubing PUN-S-DUO Technical data DUO spiral plastic tubing PUN-S-DUO Highly flexible paired plastic tubing. Two lengths of tubing are fused to gether into a tubing pair. For fitting,
the paired tubing is separated to the required length at both ends.
General technical data Type Pneumatic connection
PUN-4x0,75-S
PUN-6x1-S
PUN-8x1,25-S
PUN-10x1,5-S
PUN-12x2-S
For push-in connector O.D. 4 mm For barbed connector I.D. 3 mm with union nut For barbed connector I.D. 3 mm
For push-in connector O.D. 6 mm For barbed connector I.D. 4 mm with union nut For barbed connector I.D. 4 mm
For push-in connector O.D. 8 mm For barbed connector I.D. 6 mm with union nut For barbed connector I.D. 6 mm
For push-in connector O.D. 10 mm –
For push-in connector O.D. 12 mm –
–
–
Operating and environmental conditions [bar]
–0.95 … +10 è graph
[°C]
Compressed air to ISO 8573-1:2010 [7:–:–] –35 … +60 German Technical Control Board (TÜV)
Operating pressure p as a function of temperature t
Possible fittings
p [bar]
Temperature-dependent operating pressure Operating medium Ambient temperature Approval
Push-in fitting QS, Quick Star1) è Internet: qs
Push-in fitting QS-B, Quick Star1) è Internet: qs-b
Push-in fitting CRQS, Quick Star, stainless steel è Internet: crqs
Push-in fitting NPQM è Internet: npqm
Quick connector CK è Internet: ck
Barbed fitting CN è Internet: cn
t [°C]
1)
Recommended fitting
-H-
Note
Greater force is required when assembling the fittings CK/CN. Expanding the tube ends using a tapered mandrel makes pushing them on easier.
8
è Internet: www.festo.com/catalogue/...
Subject to change – 2015/11
Spiral plastic tubing PUN-S-DUO Technical data Materials D 52 _3 TPE-U(PU) RoHS-compliant Free of copper and PTFE
Shore hardness Tube Note on materials
Dimensions and ordering data O.D. I.D. Winding [mm]
[mm]
[mm]
4
2.6
25
6
4
46
8
5.7
60
10
7
80
12
8
95
2015/11 – Subject to change
Number of windings
Working length [m]
Block length [m]
Weight
20 45 70 23 52 168 12 27 87 9.5 22 70 9 20 64
0.5 1 1.5 1 2 6 1 2 6 1 2 6 1 2 6
0.268 0.468 0.668 0.488 0.836 2.228 0.408 0.648 1.608 0.41 0.66 1.62 0.44 0.704 1.76
25 55 84 102 230 700 130 280 870 220 490 1520 390 830 2600
Colour
Part No.
Type
Blue/black
197617 197618 197619 197620 197621 197622 197623 197624 197625 197626 197627 197628 197629 197630 197631
PUN-4x0,75-S-0,5-DUO-BS PUN-4x0,75-S-1-DUO-BS PUN-4x0,75-S-1,5-DUO-BS PUN-6x1-S-1-DUO-BS PUN-6x1-S-2-DUO-BS PUN-6x1-S-6-DUO-BS PUN-8x1,25-S-1-DUO-BS PUN-8x1,25-S-2-DUO-BS PUN-8x1,25-S-6-DUO-BS PUN-10x1,5-S-1-DUO-BS PUN-10x1,5-S-2-DUO-BS PUN-10x1,5-S-6-DUO-BS PUN-12x2-S-1-DUO-BS PUN-12x2-S-2-DUO-BS PUN-12x2-S-6-DUO-BS
[g]
Blue/black
Blue/black
Blue/black
Blue/black
è Internet: www.festo.com/catalogue/...
9
Spiral plastic tubing PUN-SG, pre-assembled Technical data Spiral plastic tubing PUN-SG Highly flexible and hydrolysisresistant pneumatic tubing with fibre reinforcement and captive rotatable fittings.
General technical data Type
PUN-10x1,5-SG
PUN-12x2-SG
Pneumatic connection 1, 2 Nominal tightening torque
Male thread G¼ 11 ±20%
Male thread Gy 12.5 ±20%
[Nm]
Operating and environmental conditions Type PUN-10x1,5-SG
1)
PUN-12x2-SG
–0.95 … +15 è graph
Temperature-dependent [bar] operating pressure Operating medium Ambient temperature [°C] Corrosion resistance class CRC1)
–0.95 … +13 è graph
Compressed air to ISO 8573-1:2010 [7:–:–] –40 … +60 1
Corrosion resistance class CRC 1 to Festo standard FN 940070 Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions).
Operating pressure p as a function of temperature t
p [bar]
1 PUN-10x1,5-SG 2 PUN-12x2-SG
t [°C] Materials A 87 _3 TPE-U(PU) Nickel-plated brass POM RoHS-compliant Free of copper and PTFE
Shore hardness Tube Connecting thread Protection against kinking Note on materials
Dimensions and ordering data O.D. I.D. Flow-relevant Winding Number of Working bending windings length radius [mm] [mm] [mm] [mm] [m] 9.5
6.4
50
42
11.7
7.9
65
51
10
21 50 66 41 53
2.4 4.8 6 4.8 6
Block length
Weight
[m]
[g]
0.889 1.165 1.317 1.172 1.312
180 340 430 480 560
è Internet: www.festo.com/catalogue/...
Colour
Part No.
Type
Blue
533463 533464 533465 533466 533467
PUN-10x1,5-SG-2,4-BL-¼ PUN-10x1,5-SG-4,8-BL-¼ PUN-10x1,5-SG-6-BL-¼ PUN-12x2-SG-4,8-BL-y PUN-12x2-SG-6-BL-y
Blue
Subject to change – 2015/11
Spiral plastic tubing PPS, pre-assembled Technical data Spiral plastic tubing PPS This hydrolysis-resistant plastic tubing demonstrates high thermal and mechanical load capacities. Each tubing length is delivered ready for
installation with 2 rotatable connectors and captive OL sealing rings. Kinks at the tubing ends are prevented by the anti-kinking springs.
General technical data Pneumatic connection 1, 2 Nominal tightening torque
Male thread G¼ 11 ±20%
[Nm]
Operating and environmental conditions Type PPS-4 –0.95 … +21.2 è graph
Temperature-dependent [bar] operating pressure Operating medium Ambient temperature [°C] Corrosion resistance class CRC1) 1)
PPS-6 –0.95 … +17.2 è graph
Compressed air to ISO 8573-1:2010 [7:–:–] –30 … +80 1
Corrosion resistance class CRC 1 to Festo standard FN 940070 Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions).
Operating pressure p as a function of temperature t
p [bar]
1 PPS-4 2 PPS-6
t [°C] Materials Tube Connecting thread Protection against kinking Note on materials
2015/11 – Subject to change
PA12-P Brass Galvanised steel RoHS-compliant
è Internet: www.festo.com/catalogue/...
11
Spiral plastic tubing PPS, pre-assembled Technical data Download CAD data è www.festo.com
Dimensions
1 Kink protection spring 2 Captive seal
Ordering data O.D. I.D.
Winding
[mm]
[mm]
[mm]
6.3
4.7
75
7.8
6.2
75
12
Number of windings
Working length [m]
Block length [m]
Weight
44 90 43 86
7.5 15 7.5 15
0.34 0.67 0.43 0.80
249 367 298 500
è Internet: www.festo.com/catalogue/...
Colour
Part No.
Type
Blue
19798 19799 19796 19797
PPS-4-7,5-¼-BL PPS-4-15-¼-BL PPS-6-7,5-¼-BL PPS-6-15-¼-BL
[g]
Blue
Subject to change – 2015/11