Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ-HR Series

SMBJ-HR Series

RoHS

Pb e3

Description

Uni-directional

The SMBJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.

Bi-directional

Features • Excellent clamping capability • Low incremental surge resistance • Typical IR ≤ 1µA for VR > 11.10V • SMT for minimal board footprint • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) • Built-in strain relief • Fast response time: typically less than 1.0ps from 0V to BV min

Agency Approvals AGENCY

AGENCY FILE NUMBER E128662/E230531

Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter

Symbol

Value

Unit

Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2)

PPPM

600

W

Power Dissipation on Infinite Heat Sink at TL=50OC

PM(AV)

5.0

W

Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3)

IFSM

100

A

Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only

VF

3.5V

V

TJ , TSTG

-65 to 150

°C

Typical Thermal Resistance Junction to Lead

RuJL

20

°C/W

Typical Thermal Resistance Junction to Ambient

RuJA

100

°C/W

Operating Junction and Storage Temperature Range

Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3.

• 600W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • VBR @TJ= VBR@25°C x (1+αT x (TJ - 25))

(αT:Temperature Coefficient)

• Glass passivated chip junction • High temperature soldering guaranteed: 260°C/40 seconds at terminals • UL Recognized compound meeting flammability rating V-0 • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant • 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01

Applications

2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal.

SMBJ-HR components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic

3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only, duty cycle=4 per minute maximum.

Functional Diagram

Bi-directional

Cathode

Anode Uni-directional 1

© 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18

Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ-HR Series

Electrical Characteristics (T =25°C unless otherwise noted) A

Part Number (Uni)

Part Number (Bi)

SMBJ5.0A-HR SMBJ6.0A-HR SMBJ6.5A-HR SMBJ7.0A-HR SMBJ7.5A-HR SMBJ8.0A-HR SMBJ8.5A-HR SMBJ9.0A-HR SMBJ10A-HR SMBJ11A-HR SMBJ12A-HR SMBJ13A-HR SMBJ14A-HR SMBJ15A-HR SMBJ16A-HR SMBJ17A-HR SMBJ18A-HR SMBJ20A-HR SMBJ22A-HR SMBJ24A-HR SMBJ26A-HR SMBJ28A-HR SMBJ30A-HR SMBJ33A-HR SMBJ36A-HR SMBJ40A-HR SMBJ43A-HR SMBJ45A-HR SMBJ48A-HR SMBJ51A-HR SMBJ54A-HR SMBJ58A-HR SMBJ60A-HR SMBJ64A-HR SMBJ70A-HR SMBJ75A-HR SMBJ78A-HR SMBJ85A-HR -

SMBJ5.0CA-HR SMBJ6.0CA-HR SMBJ6.5CA-HR SMBJ7.0CA-HR SMBJ7.5CA-HR SMBJ8.0CA-HR SMBJ8.5CA-HR SMBJ9.0CA-HR SMBJ10CA-HR SMBJ11CA-HR SMBJ12CA-HR SMBJ13CA-HR SMBJ14CA-HR SMBJ15CA-HR SMBJ16CA-HR SMBJ17CA-HR SMBJ18CA-HR SMBJ20CA-HR SMBJ22CA-HR SMBJ24CA-HR SMBJ26CA-HR SMBJ28CA-HR SMBJ30CA-HR SMBJ33CA-HR SMBJ36CA-HR SMBJ40CA-HR SMBJ43CA-HR SMBJ45CA-HR SMBJ48CA-HR SMBJ51CA-HR SMBJ54CA-HR SMBJ58CA-HR SMBJ60CA-HR SMBJ64CA-HR SMBJ70CA-HR SMBJ75CA-HR SMBJ78CA-HR SMBJ85CA-HR SMBJ90CA-HR SMBJ100CA-HR SMBJ110CA-HR SMBJ120CA-HR SMBJ130CA-HR SMBJ150CA-HR SMBJ160CA-HR SMBJ170CA-HR

Marking UNI

BI

KE KG KK KM KP KR KT KV KX KZ LE LG LK LM LP LR LT LV LX LZ ME MG MK MM MP MR MT MV MX MZ NE NG NK NM NP NR NT NV -

AE AG AK AM AP AR AT AV AX AZ BE BG BK BM BP BR BT BV BX BZ CE CG CK CM CP CR CT CV CX CZ DE DG DK DM DP DR DT DV DX DZ EE EG EK EM EP ER

Breakdown Voltage VBR (Volts) @ IT MIN

MAX

Test Current IT (mA)

6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00

7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00

10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Reverse Stand off Voltage VR (Volts) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0

Note: 1. For bidirectional type having VR of 10 volts and less, the IR limit is double. 2. 100% High Temperature Storage Life test and Reflow Simulation. 3. 100% HTRB(High Temperature Reverse Bias). For Unidirectional, 150OC/100%VR/96hours, for Bidirectional, 150OC/100%VR/192hrs(96hours for each direction for Bidirectional). 4. IR measured at room temperature +25OC 5. Each lot of parts will pass group B test requirement.

© 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18

2

Maximum Clamping Voltage VC @ Ipp (V)

Maximum Peak Pulse Current Ipp (A)

Maximum Reverse Leakage IR @ VR (µA)

9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0

65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.2

800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Agency Approval

X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X

Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ-HR Series

Screen Process 100% Vision Inspection

MIL-STD-750 method 2074

100% High Temperature Storage Life (168hrs,150°C)

MIL-STD-750 method 1031

100% X-RAY inspection

MIL-STD-750 method 2076

100% Temperature Cycle Test (-55 to150°C, 20 cycles, dwell time 15 min)

MIL-STD-750 method 1051

100% Reflow (2x)

JEDEC J-STD-020

100% Surge Test (2x)

MIL-STD-750 method 4066

100% HTRB 150°C Bias=VR(80% breakdown voltage, 96hrs, and each direction MIL–STD–750 method 1038 at 96 hrs for Bi-directional products) MIL-STD-750 method 4016.4021.4011

Final Electrical Test( 100% 3 sigma limit, 100% dynamic test and PAT limit)

Note: Up-screen program can be specified by customer’s request by contacting Littelfuse customer service

Group B Test Requirement Screen Surge test

Method

Condition

Requirement

10/1000 µs Peak Pluse Waveform

Maximum clamping Voltage (VC) @ Peak Plus Current (IPP)

Sample Size 45 perform 10x Accept 0 failures

MIL -STD-750, Method 1038.5

Applied voltage 100% VR@150°C

Sample size 45 340 hours (680 hours for bi-direction products, each direction 340 hours) Accept 0 failures

IR@VR, V(BR)@IT

Sample size 45 Accept 0 failures

Burn - In (HTRB)

Electrical test

--

I-V Curve Characteristics

Bi-directional

Uni-directional

Ipp

Vc VBR VR

IR VF IT

Vc VBR VR

V

IR IT

VR VBR Vc

V

Ipp

Ipp

PPPM VR VBR VC IR VF

IT IR

Peak Pulse Power Dissipation (IPP x VC) -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional

3

© 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18

Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ-HR Series

Ratings and Characteristic Curves (T =25°C unless otherwise noted) A

Figure 1 - TVS Transients Clamping Waveform

Figure 2 - Peak Pulse Power Rating

Voltage Transients

PPPM-Peak Pulse Power (kW)

100

Voltage or Current

Voltage Across TVS

Current Through TVS

10

1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1

0.000001

0.00001

Time

Figure 3 - Pulse Derating Curve

IPPM- Peak Pulse Current, % IRSM

Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage %

150

80 60 40 20

0

25

50

75

100

125

150

tr=10µsec

Half Value IPPM IPPM

( ) 2

50

0

175

10/1000µsec. Waveform as defined by R.E.A

td

1.0

0

2.0

3.0

4.0

t-Time (ms)

Figure 5 - Typical Junction Capacitance

Figure 6 - Steady State Power Dissipation Derating Curve

10000 PM(AV), Steady State Power Dissipation (W)

6 Bi-directional V=0V

1000

Uni-directional V=0V Uni-directional @VR

100 Bi-directional @VR

10 Tj=25C f=1.0MHz Vsig=50mVp-p

1 1.0

TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM

Peak Value IPPM

100

TA-Ambient temperature (ºC)

Cj (pF)

0.001

Figure 4 - Pulse Waveform

100

0

0.0001

td-Pulse Width (sec.)

10.0 100.0 VBR - Reverse Breakdown Voltage (V)

© 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18

5 4 3 2 1 0

1000.0

0

25

50

75

100

125

(˚C)(ºC) TA - TL-Lead AmbientTemperature Temperature

(Power Dissipation on Infinite H eat Sink )

4

150

175

Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ-HR Series

Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only

IFSM - Peak Forward Surge Current (A)

120 100 80 60 40 20 0 1

10

100

Number of Cycles at 60 Hz

Soldering Parameters

Pre Heat

Lead–free assembly

- Temperature Min (Ts(min))

150°C

- Temperature Max (Ts(max))

200°C

- Time (min to max) (ts)

60 – 180 secs

Ramp-up

TL

Average ramp up rate (Liquidus Temp (TL) to peak

3°C/second max

TS(max) to TL - Ramp-up Rate

3°C/second max

Reflow

- Temperature (TL) (Liquidus)

217°C

- Time (min to max) (ts)

60 – 150 seconds 260

Time within 5°C of actual peak Temperature (tp)

20 – 40 seconds

Ramp-down Rate

6°C/second max

Time 25°C to peak Temperature (TP)

8 minutes Max.

Do not exceed

280°C

tL

Critical Zone TL to TP

Ts(max)

Ts(min)

Ramp-down

ts

Preheat

25˚C

Peak Temperature (TP)

+0/-5

tp

TP

Temperature (T)

Reflow Condition

t 25˚C to Peak

Time (t)

°C

Environmental Specifications

Physical Specifications

High Temp. Storage

JESD22-A103

HTRB

JESD22-A108

Temperature Cycling

JESD22-A104

Weight

0.003 ounce, 0.093 grams

Case

JEDEC DO214AA. Molded plastic body over glass passivated junction

MSL

JEDEC-J-STD-020, Level 1

Polarity

Color band denotes cathode except Bidirectional

H3TRB

JESD22-A101

Terminal

Matte Tin-plated leads, Solderable per JESD22-B102

RSH

JESD22-B106

5

© 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18

Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ-HR Series

Dimensions DO-214AA (SMB J-Bend)

Dimensions

Cathode Band (for Uni-directional products only)

C

A B H D F

E

G

I Solder Pads

Millimeters

Min

Max

A

0.077

B

0.160

Min

Max

0.086

1.950

2.200

0.180

4.060

4.570

C

0.130

0.155

3.300

3.940

D

0.084

0.096

2.130

2.440

E

0.030

0.060

0.760

1.520

F

-

0.008

-

0.203

G

0.205

0.220

5.210

5.590

H

0.006

0.012

0.152

0.305

I

0.089

-

2.260

-

J

0.085

-

2.160

-

K

-

0.107

-

2.740

L

0.085

-

2.160

-

L

K

J

Inches

(all dimensions in mm)

Part Numbering System XXX C A -HR

Cathode Band

F

SMBJ

Part Marking System

High Reliability 5% VOLTAGE TOLERANCE

XX

BI-DIRECTIONAL

YMXXX

VOLTAGE

(for uni-directional products only)

Littelfuse Logo

Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code

SERIES

Packaging Part number

Component Package

SMBJxxxXX-HR

DO-214AA

Quantity

Packaging Option

3000

Tape & Reel - 12mm tape/13” reel

Packaging Specification EIA STD RS-481

Tape and Reel Specification 0.157 (4.0) 0.47 (12.0)

Cathode 0.315 (8.0)

0.059 DIA (1.5)

Cover tape

13.0 (330) 0.80 (20.2) Arbor Hole Dia.

0.49 (12.5)

© 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18

Dimensions are in inches (and millimeters).

Direction of Feed

6

(for unidirectional version only)