SECTION 8A
SEAT BELTS CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment co...
SEAT BELTS CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must be in B unless otherwise noted.
TABLE OF CONTENTS Description and Operation ................................... 8A-2
Rear Seat Belt ..................................................... 8A-4
Schematic and Routing Diagrams ....................... 8A-9 Seat Belt & Tension Reducer ............................... 8A-9
8A-2 SEAT BELTS
DESCRIPTION AND OPERATION DRIVER SEAT BELT WARNING The driver’s seat belt incorporates a seat belt warning lamp in the instrument cluster to remind the driver if the seat belt is not fastened when the ignition is turned ON. The warning lamp blinks for eight seconds with chime and goes out.
THREE-POINT FRONT SEAT BELT WITH PRETENSIONER The front seat belt contains an electronically controlled pyrotechnic retractor, pretensioner, which reduces seat belt slack when it activated in a head-on or angled front collision. The front seat belt must be replaced after an accident that causes its activation. At normal condition the driver’s seat belt operates as emergency locking retractor (ELR).
Emergency Locking Retractor (ELR) The ELR seat belt is always unlocked, allowing the passenger freedom of movement, except in emergencies such as rapid deceleration, rapid acceleration, or hard cornering maneuvers.
THREE-POINT REAR OUTBOARD SEAT BELT The rear outboard seating position uses the emergency locking retractor (ELR). Refer to Three-point front seat belt with pretensioner in this section for details.
TWO-POINT LAP REAR CENTER SEAT BELT The two-point lap rear center seat belt is a single continuous length of webbing. The webbing is routed from the anchor through plate and into a single retractor.
OPERATIONAL AND FUNCTIONAL CHECKS Caution: • Keep sharp objects and potentially damaged ob jects away from seat belts. • Avoid bending or damaging any portion of buckle or the latch plate • Do not breach or dye the belt webbing. Use only mild soap and water in order to clean the belts. • When installing the seat belt anchor bolts and screws, start the bolts and screws by hand in order to prevent cross-threading. • Do not attempt any repairs on the retractor mechanisms or covers. Replace any defective assemblies with new assemblies. • Replace any belts that are cut or damaged in any way. 1. Inspect all seat anchor bolts and screws in order to verify that they are secure. 2. Inspect the seat belt buckle. The buckle must lock and unlock easily. 3. After inserting the latch into the buckle, tug sharply on the belt. The buckle must remain locked. 4. Fully extend the shoulder belt portion to make sure that there is no twisting or tears in the belt. 5. Let the shoulder belt retract fully. The belt should retract easily.
CHILD SEAT TETHER ANCHOR There are three child seat tether anchors to hold the child seat firmly. One is located rear center of ceiling and two are located on the rear corner of floor.
SSANGYONG MY2002
SEAT BELTS 8A-3
COMPONENTS LOCATOR FRONT SEAT BELT
KAA8A010
1 2 3 4 5
Front Seat Belt Height Adjuster Front Seat Belt Upper Anchor Front Seat Belt With Pretensioner Buckle Assembly Front Seat Belt Lower Anchor
SSANGYONG MY2002
6 7 8 9
Seat Belt Retractor Bolt Seat Belt Retractor With Pretensioner Seat Belt Dust Cover and Screw Seat Belt Webbing Guide
8A-4 SEAT BELTS
REAR SEAT BELT
KAA8A020
1 2 3 4
Rear Seat Belt Upper Anchor Rear Seat Belt Webbing Hanger Rear Center Seat Belt Rear Center Seat Belt Buckle
5 6 7 8
Rear Seat Belt Buckle Rear Seat Belt Lower Anchor Rear Seat Belt Retractor Rear Seat Belt Dust Cover
SSANGYONG MY2002
yy ;; ;; yy ;; yy
SEAT BELTS 8A-5
REPAIR PROCEDURES ON-VEHICLE SERVICE THREE-POINT FRONT SEAT BELT WITH PRETENSIONER
KAA8A030
Caution: the sensing and diagnosis module (SDM) can maintain sufficient voltage to deploy the airbags and pretensioner for 0.15 minutes after the ignition is OFF and the fuse has been removed. If the airbags or pretensioners are not disconnected, do not begin service until one minute has passed after disconnecting power to the SDM. Otherwise, injury could result.
Removal and installation Procedure 1. Turn the ignition switch to LOCK and remove the key. 2. Remove the plastic cap to reveal the lower B-pillar seat belt anchor. 3. Remove the bolt and the lower B-pillar seat belt anchor. Installation Notice Tightening Torque
45 N•m (33 lb-ft)
4. Remove the lower quarter trim panel. Refer to Section 9G, Interior Trim. 5. Disconnect the pretensioner connector. 6. Remove the bolt, screw and the seat belt retractor (pretensioner). Installation Notice Tightening Torque
KAA8A040
SSANGYONG MY2002
Bolt 45 N•m (33 lb-ft)
8A-6 SEAT BELTS 7. Remove the plastic cap to reveal the upper Bpillar seat belt anchor. 8. Remove the bolt and B-pillar seat belt anchor. Installation Notice Tightening Torque
45 N•m (33 lb-ft)
9. Installation should follow the removal procedure in the reverse order.
KAA8A050
FRONT SEAT BELT HEIGHT ADJUSTER Removal and installation Procedure 1. Remove the front seat belt upper B-pillar anchor bolt. Installation Notice Tightening Torque
45 N•m (33 lb-ft)
2. Remove the rear seat belt upper anchor bolt. KAA8A060
Installation Notice Tightening Torque
45 N•m (33 lb-ft)
3. Remove the rear upper quarter trim panel. Refer to Section 9G, Interior Trim. 4. Remove the bolts and seat belt height adjuster. Installation Notice Tightening Torque
45 N•m (33 lb-ft)
5. Installation should follow the removal procedure in the reverse order.
THREE-POINT REAR OUTBOARD SEAT BELT Removal and installation Procedure 1. Remove the plastic cap to reveal the seat belt lower anchor bolt. 2. Remove the lower anchor bolt. Installation Notice Tightening Torque
45 N•m (33 lb-ft)
KAA8A070
SSANGYONG MY2002
SEAT BELTS 8A-7 3. Remove the lower quarter trim panel. Refer to Section 9G Interior Trim. 4. Remove the bolt, screw and seat belt retractor. Installation Notice Tightening Torque
Bolt 45 N•m (33 lb-ft)
KAA8A080
5. Remove the plastic cap to reveal the bolt. 6. Remove the upper anchor bolt. Installation Notice Tightening Torque
yyyy ;;;; ;;;; yyyy ;;;; yyyy
Bolt 45 N•m (33 lb-ft)
7. Installation should follow the removal procedure in the reverse order.
KAA8A090
TWO-POINT LAP REAR CENTER SEAT BELT Removal and installation Procedure 1. Fold the rear seat cushion. 2. Remove the bolts and the seat belt anchors. Installation Notice Tightening Torque
Bolt 45 N•m (33 lb-ft)
3. Installation should follow the removal procedure in the reverse order.
KAA8A100
CHILD SEAT TETHER ANCHOR Removal and installation Procedure 1. Open the tether anchor access cap if equipped. 2. Remove the bolt and the tether anchor. Installation Notice Tightening Torque
Bolt 19 N•m (14 lb-ft)
3. Installation should follow the removal procedure in the reverse order. KAA8A110
