Parts
8-1
Section 8 Parts 1. Introduction
To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use this five-column parts list, and the accompanying illustration, to describe and locate parts correctly. This section contains the following parts lists:
S FP-200 Gun System Major Components: Provides part numbers for the major components that make up the FP-200 gun system, including the gun, suspension system, and hose.
S FP-200 Gun Parts Lists: Provides part numbers for the individual parts that make up the FP-200 swirl and extrusion guns.
S Module Parts Lists: Provides part numbers for the individual parts that make up the modules that can be used with FP-200 guns.
S Nozzle Parts List: Provides part numbers for the nozzles that can be used with FP-200 guns.
S Accessories, Kits, and Recommended Spare Parts: Provides part numbers for accessories, kits, and commonly-used spare parts for the FP-200 gun system.
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-2
Parts
Using the Illustrated Parts List
Numbers in the Item column correspond to numbers that identify parts in illustrations following each parts list. The code NS (not shown) indicates that a listed part is not illustrated. A dash (–) is used when the part number applies to all parts in the illustration. The six-digit number in the Part column is the Nordson Corporation part number. A dash in this column (–) means the part cannot be ordered separately. The Description column gives the part name, as well as its dimensions and other characteristics when appropriate. Indentions show the relationships between assemblies, subassemblies, and parts.
Item
Part
Description
Quantity
--
000 000
Assembly
1
1
000 000
S Subassembly
2
2
000 000
S S Part
1
Note
A
S If you order the assembly, items 1 and 2 will be included. S If you order item 1, item 2 will be included. S If you order item 2, you will receive item 2 only. The number in the Quantity column is the quantity required per unit, assembly, or subassembly. The code AR (As Required) is used if the part number is a bulk item ordered in quantities or if the quantity per assembly depends on the product version or model. Letters in the Note column refer to notes at the end of each parts list. Notes contain important information about usage and ordering. Special attention should be given to notes.
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved
Parts
2. FP-200 Gun System Major Components
8-3
Table 8-1 lists the part numbers for the major components of the FP-200 gun system. Detailed parts lists for these components are provided later in this section. Table 8-1 FP-200 Gun System Major Components
Item Gun
Suspension package
Hose
Optional modules
E 1999 Nordson Corporation All rights reserved
Part
Description
Comments
234 896
FP-200 Swirl Gun
Comes with CF-200 wide pattern module (P/N 157 266)
234 897
FP-200 Extrusion Gun
Comes with H-200 adjustable module (P/N 276 119)
157 330
Floor-mounted column with swing arm and 4.5 kg (10 lb) capacity tool balancer
Sold as one part
724 122
Tool balancer, 6.8 kg (15 lb) capacity
Optional
100 832
RTD-style, high-flex construction hose, 7.3 m (24 ft)
Recommended for optimum performance
104 008
RTD-style, high-flex construction hose, 5 m (16 ft)
Use only if applicator is very close to gun
117 714
Extrusion module, H-200 reduced cavity, 0.30 mm (0.012 in.) orifice
Order nozzle separately.
117 804
Extrusion module, H-200 reduced cavity, 0.41 mm (0.016 in.) orifice
Order nozzle separately.
117 715
Extrusion module, H-200 reduced cavity, 0.51 mm (0.020 in.) orifice
Order nozzle separately.
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-4
Parts
3. FP-200 Gun Parts Lists FP-200 Swirl Gun Parts List (Side and Top Views) Item
Part
Description
Quantity
–
234 896
Gun, FP-200, Swirl
NS
234 965
S Shield, Heat, FP-200, Swirl
1
NS
276 644
S Clamp, Hose, 1.6 in. x 1.874 in.
12
NS
900 509
S Tubing, Polyethylene, 0.250 in. x 0.040 in., 50 ft
1
1
169 725
S Swivel, Ball, Multi-Plane,
2
220 644
S Elbow, Male, 1/4 in. x 10-32
1
3
981 735
S Screw, Fillister, 6-32 x 0.50 in. with Poly-Lok
4
4
971 607
S Connector, 10-32 x 1/4 in.
2
5
220 648
S Tubing, Air Supply, FP-200 (High Temperature)
1
6
971 618
S Union, Tube,
7
981 083
S Screw, Pan, 8-32 x 0.250 in., Slotted
2
8
983 011
S Washer, Lock, Internal, 8
6
9
971 605
S Elbow, Universal (Extrusion Air Line)
1
10
234 858
S Fitting, Hose, Barb, Swivel
1
1/
4
5/
16
in.
1
1
in., Brass
11
234 889
S Trigger, Gun, FP-200
1
12
985 216
S Pin, Dowel, 0.25 in. x 1.25 in.
1
13
271 620
S Spring, Wave, Safety
1
14
271 619
S Safety, Gun
1
15
234 888
S Shell, Handgun, Left, FP-200
1
16
234 887
S Shell, Handgun, Right, FP-200
1
17
982 743
S Screw, Socket, 8-32 x 1.375 in.
2
18
220 645
S Hose, Module, FP-200
1
19
101 887
S Clamp, Tube, 0.228 in.
1
20
234 870
S Spacer, FP-200
2
21
157 215
S Insulator, Mount
1
22
234 879
S Tube, Module, FP-200
23
973 402
S Plug, Pipe, Socket, Flush,
24
900 341
S Lubricant, Never-Seez, 16 oz
25
973 403
S Plug, Pipe, Socket, Flush,
26
157 266
S Module, CF-200, Wide Pattern
1
27
220 643
S Connector, Male, 0.125 in. x 0.125 in.
2
28
981 056
S Screw, Socket, 8-32 x 0.750 in.
2
29
983 011
S Washer, Lock, Internal, 8
2
30
234 964
S Manifold, Air, FP-200
1
31
234 880
S Tube, Manifold, FP-200
1
32
157 205
S Body, Gun, FP-200 (Service Block)
1
33
981 055
S Screw, Pan, 8-32 x 0.250 in., Slotted
6
34
178 475
S Tag, Hot Surface
1
35
220 646
S Hose, Manifold, FP-200
1
36
101 887
S Clamp, Tube, 0.228
1
37
174 881
S Cordset Assembly, FP-200 with Eyelets
1
Manual 42--FP200--MA--01 (formerly 42--88)
Note
–
1 1/
1/
8
in. (Opposite Side)
16
1 –
in.
237 478C Issued 4/99
2
E 1999 Nordson Corporation All rights reserved
8-5
Parts Item
Part
Description
Quantity
38
174 885
S Adhesive, Threadlocking
–
39
234 882
S Regulator, Air, Miniature
1
40
234 883
S Bracket, Mounting
41
972 623
S Fitting, Barbed, Elbow,
in.
1
42
981 837
S Screw, Pan, 6-32 x 0.375 in., Slotted
2
43
220 647
S Hose, Valve, FP-200
1
44
234 894
S Fitting, 10-32, T, Manifold
1
45
971 605
S Elbow, Universal (Swirl Air Line)
1
1 1/
4
in. x
1/
40
39
38
7
5
38
2
43
8 9
38
42
45
6 4
8
41
44 38
Note
38
10
3
11
12
3
13
1 38
37
36
15
16
17
8
14
18
35
19
34
20
33
21
32 31
22
30 28
24
29
27
24
23
25
24
3
26 4203216
Fig. 8-1
FP-200 Swirl Gun Parts (Side and Top Views)
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-6
Parts
FP-200 Swirl Gun Parts List (Front View, Air Valve, Wiring, and RTD) Item
Part
Description
Quantity
–
234 896
Gun, FP-200, Swirl
–
1
981 515
S Screw, Socket, 8-32 x 0.437 in.
2
2
983 011
S Washer, Lock, Internal, 8
6
3
234 875
S Plate, Mounting, Gun, FP-200
1
4
222 876
S Handle, Gun, FP-200 (Auxiliary Guide Handle)
1
5
220 643
S Connector, Male, 0.125 in. x 0.125 in
1
6
900 341
S Lubricant, Never-Seez, 16 oz
–
7
985 111
S Rivet, Blind, 3-32 x 0.125 in.
2
8
234 893
S Tag, Caution, Surface Temperature, FP-200
1
9
332 421
S Spring, 0.21 in. x 0.50 in.
1
10
981 536
S Screw, Button, Socket, 6-32 x 0.375 in.
2
11
332 419
S Guide, Puller, FP-200
1
12
271 626
S Plate, Bearing
1
13
234 869
S Washer, 0.437 in. x 0.113 in. x 0.063 in.
1
14
982 804
S Hex Nut, Lock, 4-40
1
15
332 420
S Puller, FP-200
1
16
234 884
S Valve, Cartridge, 3-Way (Air Valve)
1
17
986 503
S Retaining Ring, Internal, 37, Push-On
1
18
234 867
S Body, Valve, Air, FP-200
1
19
272 720
S Mounting Block, RTD, H-20
1
20
981 005
S Screw, Round 5-40 x 0.437 in., Slotted
2
21
939 586
S Connector, Plastic, 2 Station (Terminal Block)
1
22
972 862
S Eyelet, 0.065/0.075 in. x 0.187 in.
2
23
983 505
S Washer, Lock, Split, 5
1
24
981 000
S Screw, Fillister, 5-40 x 0.250 in., Slotted
1
25
938 129
S Heater, Cartridge, 0.375 in., 1.00 in., 80W, 240V
2
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
Note
E 1999 Nordson Corporation All rights reserved
8-7
Parts
3 2
FRONT VIEW
1
4 8
7
6
5 10
9
11
12 13 14 15
AIR VALVE
25 21
HEATER
22
18
17
16
HEATER
19 RTD
24
23
20 WIRING
RTD
4203218
Fig. 8-2
FP-200 Swirl Gun Parts (Front View, Air Valve, Wiring, and RTD)
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-8
Parts
FP-200 Extrusion Gun Parts List (Side and Top Views) Item
Part
Description
Quantity
–
234 897
Gun, FP-200, Extrusion
NS
304 250
S Shield, Heat, FP-200, Extrusion
1
NS
276 644
S Clamp, Hose, 1.6 in. x 1.874 in.
12
NS
900 509
S Tubing, Polyethylene, 0.250 in. x 0.040 in., 50 ft.
1
1
169 725
S Swivel, Ball, Multi-Plane,
2
220 644
S Elbow, Male, 1/4 in. x 10-32
1
3
981 735
S Screw, Fillister, 6-32 x 0.50 in. with Poly-Lok
4
4
971 607
S Connector, 10-32 x 1/4 in.
1
5
220 648
S Tube, Air Supply, FP-200 (High-Temperature)
1
6
971 618
S Union, Tube,
7
981 083
S Screw, Pan, 8-32 x 0.250 in., Slotted
2
8
983 011
S Washer, Lock, Internal, 8,
2
9
234 883
S Bracket, Mounting
1
10
971 605
S Elbow, Universal (Extrusion Air Line)
1
1/
4
Note
1
5/
16
in.
1
1
in., Brass
11
234 858
S Fitting, Hose, Barb, Swivel
1
12
234 889
S Trigger, Gun, FP-200
1
13
985 216
S Pin, Dowel, 0.250 in. x 1.250 in.
1
14
271 620
S Spring, Wave, Safety
1
15
271 619
S Safety, Gun
1
16
234 888
S Shell, Handgun, Left, FP-200
1
17
234 887
S Shell, Handgun, Right, FP-200
1
18
982 743
S Screw, Socket, 8-32 x 1.375 in.
2
19
101 887
S Clamp, Tube, 0.228 in.
1
20
234 870
S Spacer, FP-200
2
21
157 215
S Insulator, Mount, FP-200
1
22
234 879
S Tube, Module, FP-200
1
23
900 341
S Lubricant, Never-Seez, 16 oz
–
24
973 402
S Plug, Pipe, Socket, Flush, 1/8 in. (opposite side)
2
25
276 119
S Module, H-200 Adjustable
1
26
973 403
S Plug, Pipe, Socket, Flush,
27
981 055
S Screw, Pan, 8-32 x 0.250 in., Slotted
6
28
178 475
S Tag, Surface
1
29
157 205
S Body, Gun, FP-200 (Service Block)
1
30
220 645
S Hose, Module, FP-200
1
31
174 881
S Cordset Assembly, FP-200, with Eyelets
1
32
174 885
S Adhesive, Threadlocking
–
33
971 605
S Elbow, Universal (Inlet Air Line)
1
34
972 623
S Fitting, Barbed, Elbow, 1/4 in. x 1/8 in.
1
35
981 837
S Screw, Pan, 6-32 x 0.375 in., Slotted
2
36
220 647
S Hose, Valve, FP-200
1
37
234 885
S Fitting, Bulkhead
1
1/
16
in.
A
1
NOTE A: Reduced cavity modules may be ordered separately. Refer to Table 8-1
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved
Parts
35
34 32
8-9
33
36 37 6 7 32
5
4
8
10 32
9
11
32
3 32
2
12
13
3
14
1 32
15
31
18
16
17
19
30 29
20
28
21
27
24
8
22
3
23 23
26
25
4203217
Fig. 8-3
FP-200 Extrusion Gun Parts (Side and Top Views)
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-10
Parts
FP-200 Extrusion Gun Parts List (Front View, Air Valve, Wiring, and RTD) Item
Part
Description
Quantity
–
234 897
Gun, FP-200, Extrusion
1
1
981 515
S Screw, Socket, 8-32 x 0.437 in.
2
2
983 011
S Washer, Lock, Internal, 8
6
3
234 875
S Plate, Mounting, Gun, FP-200
1
4
222 876
S Handle, Gun, FP-200 (Auxiliary Guide Handle)
1
5
220 643
S Connector, Male, 0.125 in. x 0.125 in
1
6
900 341
S Lubricant, Never-Seez, 16 oz
–
7
985 111
S Rivet, Blind, 3-32 x 0.125
2
8
234 893
S Tag, Caution, Surface Temperature, FP-200
1
9
332 421
S Spring, 0.21 in. x 0.50 in.
1
10
981 536
S Screw, Button, Socket, 6-32 x 0.375 in.
2
11
332 419
S Guide, Puller, FP-200
1
12
271 626
S Plate, Bearing
1
13
234 869
S Washer, 0.437 in. x 0.113 in. x 0.063 in.
1
14
982 804
S Hex Nut, Lock, 4-40
1
15
332 420
S Puller, FP-200
1
16
234 884
S Valve, Cartridge, 3-Way (Air Valve)
1
17
986 503
S Retaining Ring, Internal, 37, Push-on
1
18
234 867
S Body, Valve, Air, FP-200
1
19
272 720
S Mounting Block, RTD, H-20
1
20
981 005
S Screw, Round, 5-40 x 0.437 in., Slotted
2
21
939 586
S Connector, Plastic, 2 Station (Terminal Block)
1
22
972 862
S Eyelet, 0.065/0.075 in. x 0.187 in.
2
23
983 505
S Washer, Lock, Split, 5
1
24
981 000
S Screw, Fillister, 5-40 x 0.250 in., Slotted
1
25
938 129
S Heater, Cartridge, 0.375 in., 1.00 in., 80W, 240V
2
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
Note
E 1999 Nordson Corporation All rights reserved
8-11
Parts
3 2
FRONT VIEW
1
4 8
7
6
5 10
9
11
12 13 14 15
AIR VALVE
25 21
HEATER
22
18
17
16
HEATER
19 RTD
24
23
20 WIRING
RTD
4203219
Fig. 8-4
FP-200 Extrusion Gun Parts (Front View, Air Valve, Wiring, and RTD)
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-12
Parts
4. Module Parts Lists CF-200 Wide Pattern Swirl Module Parts List Item
Part
Description
Quantity
–
157 266
Module, CF-200, Wide Pattern
–
1
272 288
S Screw, Loading
1
2
272 289
S Nut, Locking, 1/2-28
1
3
276 112
S Air Cap, Adjuster
1
4
987 022
S Spring, Compression, 1.146 in. x 0.360 in. x 0.065 in.
1
5
272 290
S Needle with Piston, H-200
1
6
940 111
S O-ring, Viton, 0.301 in. x 0.070 in.
3
7
276 113
S Body, Module
1
8
157 269
S Seat, with Carbide
1
9
119 202
S Nut, Nozzle Retaining, CF-WS
1
10
860 258
S Screw, Fillister, 8-32 x 0.875 in.
4
11
238 716
S Screw, Socket, Cap, 10-32 with O-ring
1
12
981 758
S Screw, Fillister, 6-32 x 0.625 in.
2
13
900 223
S Lubricant, O-ring, Parker 4 oz
–
14
145 671
S Seal, Spring Load
1
15
940 121
S O-ring, Viton, 0.364 in. x 0.070 in.
1
17
986 502
S Retaining Ring, Internal, 43, Push-on
1
18
983 012
S Disc, Seal Support
2
19
750 553
S Seal, Hat, Formed
2
21
144 892
S Spring, Compression, 0.420 in. x 0.500 in.
1
Note A
B
C
NOTE A: This item is a replacement assembly. B: This item is a kit containing 10 o-ring and screw assemblies. C: This item is a kit containing 10 seals.
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved
Parts
8-13
2
1
7
13
6
21
11
12
3 14
18
4 13
5
15
17 8
13
18
6
19 10 9
4201010A
Fig. 8-5
CF-200 Wide Pattern Swirl Module Parts
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-14
Parts
H-200 Adjustable Module Parts List Item
Part
Description
Quantity
–
276 119
Module, H-200 Adjustable
–
1
986 502
S Retaining Ring, Internal, 43, Push-on
1
2
276 113
S Body, Module
1
3
983 012
S Disc, Seal Support
2
4
750 553
S Seal, Hat, Formed
4
5
145 671
S Seal, Spring Load
1
6
940 111
S O-ring, Viton, 0.301 in. x 0.070 in.
2
9
981 758
S Screw, Fillister, 6-32 x 0.625 in.
2
10
272 288
S Screw, Loading
1
11
272 289
S Nut, Locking, 1/2-28
1
12
987 022
S Spring, Compression, 1.146 in. x 0.360 in. x 0.065 in.
1
13
276 112
S Air Cap, Adjuster
1
14
272 290
S Needle with Piston, H-200
1
17
940 121
S O-ring, Viton, 0.364 in. x 0.070 in.
1
18
–
S Seat, with Carbide, H-200
1
19
981 572
S Screw, Oval, 8-32 x 0.375 in., Slotted
4
20
238 716
S Screw, Socket, Cap, 10-32 with O-ring
2
23
144 892
S Spring, Compression, 0.420 in. x 0.50 in.
1
Note A
B
C
NOTE A: This item is a replacement assembly. B: This item is a kit containing 10 seals. C: This item is a kit containing 10 o-ring and screw assemblies.
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved
Parts
8-15
11
10
2
12 6 20
9
13
5 3
14
23 17
18 1 3 19
4
4201001
Fig. 8-6
H-200 Adjustable Module Parts
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-16
Parts
H-200 Reduced Cavity Module Parts List Item
Part
Description
Quantity
Note
–
117 714
Module, H-200 Reduced Cavity, 0.012 in.
–
A
–
117 804
Module, H-200 Reduced Cavity, 0.016 in.
–
A
–
117 715
Module, H-200 Reduced Cavity, 0.020 in.
–
A
1
272 288
S Screw, Loading
1
2
272 289
S Nut, Locking, 1/2-28
1
3
276 112
S Air Cap, Adjuster
1
4
981 001
S Screw, Pan, 4-40 x 0.187 in., Slotted
1
5
900 419
S Adhesive, Retaining Cylindrical
–
6
900 303
S Lubricant, Silicone
–
7
272 294
S Washer, Seal, Piston
1
8
940 111
S O-ring, Viton, 0.301 in. x 0.070 in.
2
9
940 121
S O-ring, Viton, 0.364 in. x 0.070 in.
1
13
276 113
S Body, Module
1
14
272 293
S Washer, Piston
2
15
981 758
S Screw, Fillister, 6-32 x 0.625 in.
2
16
900 236
S Sealant, Paste
–
17
987 022
S Spring, Compression, 1.146 in. x 0.360 in. x 0.065 in.
1
18
238 716
S Screw, Socket, Cap, 10-32 with O-ring
2
19
981 064
S Screw, Pan, 8-32 x 0.375, Slotted
4
20
986 502
S Retaining Ring, Internal, 43, Push-on
1
21
983 012
S Disc, Seal Support
2
22
750 553
S Seal, Hat, Formed
4
23
145 671
S Seal, Spring Load
1
C
25
161 336
S Nozzle Assembly with Needle, 0.012 in.
–
D
25
161 337
S Nozzle Assembly with Needle, 0.016 in.
–
D
25
161 338
S Nozzle Assembly with Needle, 0.020 in.
–
D
26
144 892
S Spring, Compression, 0.420 in. x 0.50 in.
1
B
NOTE A: This item is a replacement assembly. B: This item is a kit containing 10 o-ring and screw assemblies. C: This item is a kit containing 10 seals. D: Order the size (0.012, 0.016, 0.020) that matches the module size.
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved
Parts
8-17
2
1
13
17
8
18
4
3 23 15 14 21 7 26 25
9
20 25
21
22
19
22
4201004
Fig. 8-7
H-200 Reduced Cavity Module Parts
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Manual 42--FP200--MA--01 (formerly 42--88)
8-18
Parts The FP-200 gun accommodates any standard H-200 extrusion nozzle. Table 8-2 lists the part numbers for nozzles commonly used with the FP-200 gun.
5. Nozzle Parts List
Table 8-2 Nozzles Commonly Used with the FP-200 Gun Nozzle Type
Part No.
Description
Wide pattern s irl nozzles swirl no les
125 607
0.64 mm (0.025 in.) orifice diameter
131 998
0.76 mm (0.030 in.) orifice diameter
131 635
1.17 mm (0.046 in.) orifice diameter
104 100
0.20 mm (0.008 in.) orifice diameter
104 101
0.25 mm (0.010 in.) orifice diameter
860 548
0.31 mm (0.012 in.) orifice diameter
860 574
0.36 mm (0.014 in.) orifice diameter
860 575
0.41 mm (0.016 in.) orifice diameter
860 226
0.46 mm (0.018 in.) orifice diameter
860 435
0.51 mm (0.020 in.) orifice diameter
100 728
0.64 mm (0.025 in.) orifice diameter
810 381
0.76 mm (0.030 in.) orifice diameter
810 382
1.02 mm (0.040 in.) orifice diameter
810 300
1.27 mm (0.050 in.) orifice diameter
710 245
0.64 mm (0.025 in.) orifice diameter
56 mm (2.2 in.) engagement length
709 018
1.07 mm (0.042 in.) orifice diameter
710 246
1.55 mm (0.061 in.) orifice diameter
Use with H-200 adjustable module (P/N 276 119)
724 268
2.29 mm (0.090 in.) orifice diameter
703 223
4.75 mm (0.187 in.) orifice diameter
Swirl nozzles
Extended e tr sion extrusion nozzles
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
Notes One-piece nozzle and nut assembl assembly Use with CF-200 wide pattern module (P/N 157 266) Use with CS-WF nozzle retaining n t (P/N 119 202) nut Use with CF-200 wide pattern module ((P/N 157 266))
E 1999 Nordson Corporation All rights reserved
Parts
8-19
Tables 8-3 through 8-7 list commonly used accessories, kits, and spare parts for the FP-200 gun.
6. Accessories, Kits, and Recommended Spare Parts
Table 8-3 FP-200 Gun Accessories and Kits Part
Description
Notes
303 028
Conversion Kit, Extrusion to Swirl, FP-200 Gun
This kit may be used to convert an FP-200 extrusion gun (P/N 234 896) to an FP-200 swirl gun (P/N 234 897). It cannot be used to convert an air-control-kit FP-200 extrusion gun (P/Ns 176 122 and 157 253) to a current FP-200 extrusion gun (P/N 234 896). Order the heat shield separately.
303 029
Conversion Kit, Swirl to Extrusion, FP-200 Gun
This kit may be used to convert an FP-200 swirl gun (P/N 234 897) to an FP-200 extrusion gun (P/N 234 896). It cannot be used to convert an air-control-kit FP-200 swirl gun (P/Ns 173 209 and 153 609) to a current FP-200 swirl gun (P/N 234 897). Order the heat shield separately.
234 970
Heat Shield, FP-200 Extrusion Gun
Order with conversion kit P/N 303 029 (swirl to extrusion).
234 965
Heat Shield, FP-200 Swirl Gun
Order with conversion kit P/N 303 028 (extrusion to swirl).
It is not necessary to order a heat shield unless you are ordering a conversion kit. Nordson FP-200 FP 200 guns (P/Ns 234 896 and 234 897) come with a heat shield. The heat shield is required for the gun to meet CE approval standards.
Table 8-4 Other Accessories Part
Description
901 915
Nozzle Cleaning Kit
900 298
Heat-conductive Paste
132 426
Hose/gun diagnostic device with cable assembly
E 1999 Nordson Corporation All rights reserved
237 478C Issued 4/99
Note
Manual 42--FP200--MA--01 (formerly 42--88)
8-20
Parts
6. Accessories, Kits, and Recommended Spare Parts (contd.)
NOTE: Replacement modules are available as new or rebuilt parts. Contact the Nordson Customer Service Center for information on rebuilt modules available through the Rebuild/Exchange (RBX) program.
Table 8-5 Module Replacement Kits Part
Description
117 714
Service Kit, Extrusion Module, H-200 Reduced Cavity, 0.30 mm (0.012 in.) orifice
117 804
Service Kit, Extrusion Module, H-200 Reduced Cavity, 0.41 mm (0.016 in.) orifice
117 715
Service Kit, Extrusion Module, H-200 Reduced Cavity, 0.51 mm (0.020 in.) orifice
276 119
Service Kit, Module, H-200 Adjustable
Note
A
NOTE A: Order nozzle separately.
Table 8-6 Module Rebuilding Kit Part 272 818
Description
Note
Service Kit, Seal, H-200 Module
A
NOTE A: This kit can be used to rebuild the H-200 adjustable module (P/N 276 119) or the CF-200 swirl module (P/N 157 266). Order nozzles separately.
Table 8-7 Recommended Spare Parts Part
Description
Note
169 725
Swivel, Ball, Multi-plane, 5/16 in.
938 129
Heater Cartridge, 0.038 in. x 1.00 in., 240V, 80W (Two per gun.)
986 503
Retaining Ring, Internal, 37, Push-on (Required when replacing air valve.)
234 884
Valve, Cartridge, 3-way (Air Valve)
174 881
Cordset Assembly, FP-200 with Eyelets (Includes RTD.)
972 862
Eyelet, 0.065/0.075 x 0.187 in.
A
982 804
Hex Nut, Lock, 4-40
A
271 620
Spring, Wave, Safety
A
NOTE A: These items are easily misplaced when performing maintenance or repairs.
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved
9-2
Options Refer to the following for parts included in the Heated Air Manifold Kit.
2. Parts Item
Part
—
724 795
Kit, heated air manifold, FP-200
1
A
1
135 972
S Cable, adapter, 6P/12S, 24 ft., T-style
1
B
2
274 685
S Cordset assembly, 2300
1
3
984 155
S Nut, panel mounting
1
983 161
S Washer, lock, e-ring, 3/8
1
4
Description
1/ 4
Quantity
5
815 965
S Tubing,
OD x .1, 1 ft.
6
981 020
S Screw, pan, 6-32 x .250, slotted 1/ 4
1 1/ 8
3
7
971 154
S Connector, male,
8
220 787
S Manifold, heated air, FP200
1
9
981 516
S Screw, socket-head, 8-32 x 1.125
2
10
972 508
S Nut, with ferrule,
NS
900 236
S Sealant, paste
1/ 4
tube x
Note
NPT, brass
1
tube, brass
1 —
NOTE A: Air regulator is not included with the heated air manifold kit. E: Install this cable adapter between the heated air manifold kit and the applicator. NS: Not Shown
1
2, 3, 4 5 6 10 7 8
9 Fig. 9-1
4601142C
Gun with Heated Air Manifold
Manual 42--FP200--MA--01 (formerly 42--88)
237 478C Issued 4/99
E 1999 Nordson Corporation All rights reserved