SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Preparation NOTE: Part number of this accessory may not be the same as the part number shown. General Applicability
Part Number: PT545-00112 Kit Contents Item # 1 2 3 4
Quantity Reqd. 1 1 1 1
5 6 7
1 1 1
Description Receiver Assembly Navigation Owner’s Manual Hardware Bag Template A (to locate bracket mounting location) Antenna Bag Receiver Bracket Navigation Harness
Quantity Reqd. 4 17 3 2 Quantity Reqd. 1 1 2
Item #
Quantity Reqd. 1
Description Antenna Earth Plate Velcro Tape Description PT545-00111
Conflicts None
Recommended Tools Personal & Vehicle Protection
Blanket
Installation Tools
Notes
Ratchet Extension Socket Torque Wrench Screwdriver Masking Tape Panel Clip Removal Tool Wrench Scissor Matt Knife
STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue.
10 mm Socket & Deep Socket, 14 mm 4.1 N-m (36 in-lbf), 3.7 N-m (27 in-lbf) Phillips, #2 (2” wide) e.g. Toyota SST P/N: 00002-06022-01 Open End, 10 mm
Special Chemicals
Notes
Cleaner
VDC Approved Cleaner Page 1 of 16 pages
Issue: C
10/10/10
Description
SAFETY TORQUE: This mark indicates that torque is related to safety.
Notes
Safety Goggles Seat Protector Vehicle Protection
Quantity Reqd.
Legend
Additional Items Required For Installation Item # 1
Accessory VIP-RS3200+ Remote Engine Start Interior Lights Subwoofer Satellite Radio Audio System/Navi System
Vehicle Service Parts (may be required for reassembly)
Description Screw (M4x8) Lock Tie Cushion Tape Foam Tape
Antenna Bag Contents Item # 1 2 3
Item # 1 2 3 4 5 6
*Mandatory
Hardware Bag Contents Item # 1 2 3 4
Recommended Sequence of Application
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Preparation Parts Description of Receiver Assembly Navigation Unit (PT545-00112)
Item #
Parts Name
1 2 3 A B C D 4 5 A B C 6 7
Receiver Assembly Navigation Owner’s Manual Hardware Bag Screw (M4x8) Lock Tie Cushion Tape Foam Tape Template A Antenna Bag Antenna Earth Plate Velcro Tape Receiver Bracket Navigation Harness
Page 2 of 16 pages Issue: C
10/10/10
Qty 1 1 1 4 17 3 2 1 1 1 1 2 1 1
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). Safety (eye protection, rechecking torque procedure, etc.). Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Scion dealer for a copy of this document.
1. Vehicle Protection. (a) Remove the negative battery cable (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool when removing cable.
2. Vehicle Disassembly. NOTE: Place all remove parts on a protected surface. NOTE: When disconnecting wiring connectors, do not pull on the wiring, pull on the connector only. NOTE: Engage the parking brake while working. (a) Remove the shift lever knob (Fig. 2-1). NOTE: For manual transmission only.
Shift lever knob
Fig. 2-1
Page 3 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure Panel Removal Tool Clips (x6)
(b) Remove the lower right instrument pad cushion (Fig. 2-2). (1) Using a panel removal tool, detach the six (6) clips and remove the pad cushion.
Lower right instrument pad cushion
Fig. 2-2
(c) Remove the console cluster.
Panel Removal Tool
(1) Disengage five (5) clips and remove the console cluster (Fig. 2-3).
Clips (x5)
(2) Disconnect the connectors.
Console cluster
Fig. 2-3
(d) Remove the console upper panel. Panel Removal Tool
(1) Disengage four (4) clips and remove the console upper panel (Fig. 2-4).
Clips (x4)
(2) Disconnect one (1) clip.
Console upper panel
Fig. 2-4
(e) Remove the lower center cluster. Panel Removal Tool
(1) Disengage six (6) clips and remove the console cluster (Fig. 2-5). (2) Disconnect the connectors.
Lower center cluster
Clips (x6)
Fig. 2-5 Page 4 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure (f) Remove the center cluster.
Panel Removal Tool
Clips (x5)
(1) Disengage five (5) clips and remove the center cluster (Fig. 2-6). Make sure to disengage the harness at the top of the panel.
Center cluster
Fig. 2-6
(g) Remove the radio bracket.
Ratchet, 10mm Socket (Deep), Extension
(1) Remove four (4) nuts and radio brackets (L and R) (Fig. 2-7).
Nuts (x4)
Radio bracket (L)
Radio bracket (R)
Fig. 2-7
(h) Remove the meter cluster side panel. Panel Removal Tool Clips (x4)
(1) Using a panel removal tool, detach the four (4) clips and remove the pad cushion (Fig. 2-8). (2) Disconnect the connectors.
Meter cluster side panel
Fig. 2-8
(i) Remove the meter cluster panel.
Panel Removal Tool Clips (x8)
(1) Using a panel removal tool, detach the eight (8) clips and remove the meter cluster panel (Fig. 2-9).
Meter cluster panel
Fig. 2-9
Page 5 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure Screwdriver
(j) Remove the combination meter assembly.
Screw (x1)
(1) Remove the one (1) screw, disengage two (2) clips and then remove the combination meter assembly (Fig. 2-10).
Fig. 2-10
A
Combination meter assembly
B
Clips (x3)
B
A
NOTE: Hold the part labeled A in Fig. 2-11 and detach the clips. Do not hold the part labeled B in Fig. 2-11.
(2) Disconnect the connectors. Fig. 2-11
(k) Remove the driver seat track bracket cover outer side.
Screwdriver
Clips (x2)
(1) Using a screwdriver, detach two (2) clips and remove the bracket cover (Fig. 2-12). NOTE: Tape the screwdriver tip before use.
Fig. 2-12
Screwdriver
(l) Remove the driver seat track bracket cover inner side. (1) Using a screwdriver, detach three (3) clips and remove the cover (Fig. 2-13). NOTE: Tape the screwdriver tip before use. (m) Remove front seat assembly.
Fig. 2-13
(1) Lift up the seat track adjusting handle and move the seat to the rearmost position. Page 6 of 16 pages
Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure (2) Remove two (2) bolts on the front side of the seat (Fig. 2-14).
14mm Socket
Bolts (x2) Bolts (x2)
(3) Lift up the seat track adjusting handle and move the seat to the foremost position. (4) Remove two (2) bolts on the rear side of the seat (Fig. 2-14).
Fig. 2-14
(5) Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position. (6) Tilt the seat back to install the navigation receiver. Remove one (1) clip under the seat. NOTE: Be careful not to damage the vehicle body.
3. Install the Navigation Receiver. (a) Install the navigation receiver onto the bracket using four (4) 4 mm machine screws (Fig. 3-1).
Screwdriver
Screws (x4)
NOTE: Ensure the arrow of the navigation receiver is facing the front of the bracket (Fig. 31). NOTE: The triangle mark must face toward the hole of the bracket.
Fig. 3-1
Page 7 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure (b) Install the bracket. Cushion Tape (x2)
(1) Install two (2) cushion tapes onto the bottom of the base bracket (Fig. 3-2). (2) Clean the mounting surface of the bracket. Use a VDC-approved cleaner and cleaning method. Fig. 3-2
(c) Fold the short edge of template A. Matt Knife
Template A
(d) Position template A under the driver’s seat as shown. (1) Align the template so the folded edge of template lines up next to the amplifier (Fig. 3-3).
Amplifier
Fig. 3-3
(e) Using a matt knife, cut the carpet all the way through to the floor. (1) Make sure there are no wires under the carpet where the cuts are made. (2) Cut the full length of the cutting lines on the template. (3) Clean the bracket mounting surface of the vehicle floor pan. Use a VDC-approved cleaner and cleaning method. (f) Insert the bracket into the opening. Position the bracket until the bracket is stable.
Side cutter
Lock tie (x1)
(g) Remove the release paper from two (2) pieces of cushion tape A. (1) Make sure to push all the lint away from the cushion tape. Press down to secure the bracket to the vehicle.
Navigation harness and GPS Antenna cable
Fig. 3-4
(h) Route the navigation harness and GPS antenna cable under the carpet to the opening of carpet under the driver’s seat and secure with one (1) lock tie (Fig. 3-4). Page 8 of 16 pages
Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure (1) Make sure there are no cables disturbing driver seat track. (i) Connect the three (3) connectors into the navigation receiver (Fig. 3-5).
Side Cutter
(1) Connect main navigation cable. (2) Connect navigation power cable. (part of navigation cable) (3) Connect GPS antenna cable. Lock Tie (x2)
Fig. 3-5
(j) Secure the cables using two (2) lock ties (Fig. 3-5). (1) Wrap cables with one lock tie and secure cables to mounting bracket with the second lock tie. (Fig. 3-5) 4. Route Cables to the Head Unit.
Side Cutter
(a) Route the navigation cable and GPS antenna cable along with the vehicle harness and secure with one (1) lock tie (Fig. 4-1).
Navigation cable and GPS antenna cable
Vehicle harness Lock tie (x1)
Fig. 4-1
(b) Route the navigation cable and GPS antenna cable at the center console (Fig. 4-2).
Navigation cable and GPS Antenna cable
Vehicle harness
Fig. 4-2 Page 9 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure Side Cutter
Navigation cable and GPS antenna cable
Lock tie (x2)
Fig. 4-3
(c) Route the navigation cable, GPS antenna cable along with the vehicle harness from the center console. (d) Secure the navigation cable and GPS antenna cable with two (2) lock ties behind the center console (Fig. 4-3).
Vehicle harness
Side Cutter
GPS antenna cable
(e) Route the GPS antenna cable along with the vehicle harness behind the head unit (Fig. 4-4).
Vehicle harness Lock tie (x1)
Navigation cable Lock tie (x1)
(f) Secure the navigation cable and GPS antenna cable together with one (1) lock tie at the vehicle harness (Fig. 4-4).
Vehicle harness
(g) Secure the navigation cable with one (1) lock tie at the vehicle harness (Fig. 4-4).
Fig. 4-4
Page 10 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure 5. Install the GPS Antenna. (a) Clean the AC duct surface. Use a VDCapproved cleaner and cleaning method.
Side cutter Velcro tape (x2)
Earth plate
(b) Remove the release paper from the double sided tape at the earth plate and apply the two (2) Velcro tape to the bottom of the earth plate (Fig. 5-1-1).
AC duct
Fig. 5-1-1
GPS Antenna
(c) Attach the earth plate to the area indicated by the hatched lines in the illustration (Fig. 5-1-1).
Foam tape AC duct
(d) Attach the GPS antenna to the center of the earth plate (Fig. 5-1-2).
Antenna cable
Fig. 5-1-2 AC duct
(e) Secure the GPS antenna with one (1) foam tape to the vehicle harness as shown in the illustration (Fig. 5-1-2).
Antenna cable
NOTE: Cover the GPS antenna cable with foam tape all way to the edge of antenna.
Vehicle harness Lock tie (x1)
(f) Route and secure the GPS antenna cable with one (1) lock tie to the vehicle harness as shown in the illustration (Fig. 5-1).
Fig. 5-1
(g) Bundle the navigation cable and GPS antenna cable at the center console using two (2) lock ties (Fig. 5-2).
Side cutter
(1) Provide the sufficient cable length, so the bundle will be tied at the vehicle harness comfortably.
Lock tie (x2)
Lock tie (x1) Vehicle harness
(2) Secure the navigation cable and GPS antenna cable to the vehicle harness with one (1) lock tie (Fig. 5-2).
Navigation cable and GPS Antenna cable
Fig. 5-2
Page 11 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure (h) Place bundled navigation cable and GPS antenna cable inside the center console (Fig. 5-3).
Side cutter
Navigation cable and GPS Antenna cable
Fig. 5-3
6. Install the Head Unit (a) Install the brackets. Phillips Screwdriver
Bolts (M5x8) (x6)
Fig. 6-1
Right Side View
(1) Install the brackets (L and R) onto the head unit with six (6) bolts (M5x8) (Fig. 6-1).
Bracket (R)
Head Unit
Ratchet, 10mm Socket (Deep), Extension, Bolts(x2)
(b) Install the head unit. (1) Connect the connectors to the head unit. (2) Install the head unit onto the vehicle with and four (4) bolts (Fig. 6-2).
Fig. 6-2
Bolts (x2)
Page 12 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure 7. In Process Functionality Test (a) Temporarily reconnect the negative battery cable. (b) Temporarily install the DCC (c) Turn ignition key to the “ACC” position. (d) Verify the connection of the tuner/player. Press the POWER button on the tuner/player head unit. Verify that the display turns on. (e) Verify the connection of the navigation. Press the NAV button on the head unit. Verify the disclaimer screen is shown. (1) Press the “I Accept” soft key (Fig. 7-1).
Fig. 7-1
(2) Press the “Info” soft key (Fig. 7-2).
Fig. 7-2
(3) Press the “GPS” soft key (Fig. 7-3).
Fig. 7-3
(4) Wait approx. 60 seconds for GPS signals start to appear (yellow or gray bars) (Fig. 7-4). NOTE: If no yellow or gray bars are displayed, the GPS antenna cable may not be connected on the navigation receiver. Navigation might not be able to receive GPS signal in a covered area. Check in an open area if possible.
Fig. 7-4
Page 13 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure (5) Exit by pressing the “Map” soft key in the lower right corner of the display (Fig. 7-5).
Fig. 7-5
8. Set the Car Type. (a) After the head unit turns on, press the MENU button ① (Fig. 8-1). ② ①
Fig. 8-1
(b) From the menu setting screen, press the “Car Type” soft key (Fig. 8-2).
Fig. 8-2
(c) Press the right arrow soft key until the car type “tC” is displayed (Fig. 8-3). (d) Exit by pressing the RETURN button ② twice (Fig. 8-1). The car type setting is saved. (e) Disconnect the negative battery cable. Fig. 8-3 Page 14 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Procedure 9. Complete the Installation. (a) Reassemble the vehicle. (b) Tighten the seat to 3.7 N-m (27 in-lbf). Screwdriver
Tab
(c) Line up tab of the combination meter assembly. (Fig. 9-1) (d) Reconnect any disconnected connectors. (e) Verify the panels fit together properly with no uneven gaps between them. Fig. 9-1
Combination meter assembly
(f) Clean up and remove any trash. (g) Place owner’s manual in the glove box. (h) Reconnect the battery cable. Tighten the nut to 4.1 N-m (36 in-lbf). (i) Perform functional check again.
Page 15 of 16 pages Issue: C
10/10/10
PPO
SCION
tC
2011 -
SCION NAVIGATION SYSTEM
Checklist - these points MUST be checked to ensure a quality installation. Check:
Look For:
Accessory Function Checks Radio receiver assembly
Functioning radio receiver assembly. Refer to the receiver assembly manual and the radio owner’s manual. AM/FM reception.
Antenna is functional. Functioning navigation receiver. Navigation receiver Verify the proper operation of the satellite Satellite radio tuner
radio tuner. Refer to the tuner assembly and tuner owner’s manual.
Connect the USB checker to the USB &
Verify the proper operation of the USB
AUX jack and check the speaker emits
connector.
sound.
Verify the proper operation of AUX
AUX
connector.
Vehicle Function Checks Steering wheel audio controls
Functioning audio controls.
Rheostat
Functioning dimmer control.
Remove the DCC audio fuse. (PPO only) Hazard switch
Functioning hazard switch.
Air conditioner
Functioning air conditioner.
Front passenger seat belt monitor
Functioning front passenger seat belt M.
Door key lock monitor
Functioning door key lock monitor.
Cigarette lighter
Functioning cigarette lighter.
Power Sun/Moon roof
Functioning power sun/moon roof.
VSC
Functioning VSC off button.
Page 16 of 16 pages Issue: C
10/10/10
PPO
