SE5 Rotary Mower Rev 09-06
S/N 41507-Current
Part No. 00768613P
PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800-446-5158) to obtain a Free copy before operating the equipment.
RHINO® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email:
[email protected]
© 2006 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!
WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
PARTS SECTION
Parts Section – 1
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE:
Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals.
For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:
RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email:
[email protected]
©2006 Alamo Group Inc.
Parts Section – 2
PART NAME INDEX A-FRAME ASSEMBLY - LIFT TYPE ...................................................................................................................................... 4 BLADE PAN ASSEMBLY ..................................................................................................................................................... 21 CASTER FORK WHEEL ASSY S/N 39050-40386 & 41507-Current Pub 03-05 ................................................................ 12 CHAIN GUARD ASSEMBLY - FRONT (OPTION) ............................................................................................................... 33 CHAIN GUARD ASSEMBLY - REAR (OPTION) ................................................................................................................. 34 CHECK CHAIN ASSEMBLY (EXTRA EQUIPMENT)........................................................................................................... 35 DEFLECTOR ASSEMBLY - FRONT Rev 06-05 .................................................................................................................. 31 DEFLECTOR ASSEMBLY - REAR ...................................................................................................................................... 32 DRIVELINE ........................................................................................................................................................................... 29 DRIVELINE ASSEMBLY - SHEAR PIN S/N 39824-BELOW Rev 10-04 ............................................................................. 24 DRIVELINE ASSEMBLY - SLIP CLUTCH S/N 39374 -BELOW Rev 10-04 ........................................................................ 26 DRIVELINE ASSEMBLY S/N 39375 -CURRENT Pub 10-04 .............................................................................................. 22 DRIVELINE ASSEMBLY S/N 39825 -CURRENT Rev 09-05 .............................................................................................. 28 GEARBOX ASSEMBLY Rev 09-05 ...................................................................................................................................... 18 MOLDED TIRE ASSY Rev 10-04......................................................................................................................................... 11 OFFSET ADAPTER THREE-POINT (EXTRA EQUIPMENT) .............................................................................................. 36 SAFETY DECAL SHEETS ................................................................................................................................................... 37 SHIELD ASSEMBLY - U-JOINT ........................................................................................................................................... 20 SLIP CLUTCH ASSEMBLY S/N 39374 -BELOW Rev 10-04 .............................................................................................. 30 TAIL WHEEL ASSEMBLY - PULL TYPE Rev 08-04 ........................................................................................................... 16 TAIL WHEEL HUB ASSY S/N 39050-40386 & 41507-Current Rev 09-06.......................................................................... 13 TAILWHEEL ASSEMBLY - LIFT TYPE S/N 39049-BELOW Pub 11-04 ............................................................................... 8 TAILWHEEL ASSY -LIFT TYPE S/N 39050-40386 & 41507-Current Pub 03-05 ............................................................... 10 TAILWHEEL ASSY-LIFT TYPE S/N 40387-41506 Pub 03-05 .............................................................................................. 6 TONGUE ASSEMBLY - PULL TYPE Rev 08-04 ................................................................................................................. 14
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 3
A-FRAME ASSEMBLY - LIFT TYPE
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 4
A-FRAME ASSEMBLY - LIFT TYPE ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 14 15 16
00765331 00764839 00757949 00757953 00766587 00766586 00603500 00766086 37107B13 00755881 00762365 00770776 00770772 00770773 37107B12
2 2 1 1 1 1 2 8 1 10 2 8 1 1 1
BAR - LIFT STRAP BAR, A-FRAME LINK - TOP BUSHING, A-FRAME PLATE, HITCH EAR RH PLATE, HITCH EAR LH CAT. 1 HITCH PIN, NUT, & WASHER WASHER PIN LOCKNUT BOLT BOLT BOLT LOCKNUT PIN
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 5
TAILWHEEL ASSY-LIFT TYPE S/N 40387-41506 Pub 03-05
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 6
TAILWHEEL ASSY-LIFT TYPE S/N 40387-41506 Pub 03-05 ITEM
PART NO.
QTY.
DESCRIPTION
1 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 21 22
0891020100 00768968 00766611 00770781 00770777 02963669 00755881 0891030100 15B2000 00036900 00766603 00765337 00013701 00013600 00130010 00756750 00756760 00750621
1 1 1 4 4 2 2 1 1 1 1 2 2 2 1 1 1 2
TAIL WHEEL BEAM WELDMENT NUT GAUGE WHEEL MOUNT WELDMENT BOLT NUT BOLT NUT CASTER FORK WELDMENT WASHER COTTER PIN SPINDLE LOCK WELDMENT W/NUT SPACER BEARING CONE SEALS TIRE AND WHEEL ASSY - LAMINATED TIRE TIRE, WHEEL, CUPS WHEEL & TIRE ASSY - MOLDED TIRE (ITEMS 19-21) BEARING CUP
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 7
TAILWHEEL ASSEMBLY - LIFT TYPE S/N 39049-BELOW Pub 11-04
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 8
TAILWHEEL ASSEMBLY - LIFT TYPE S/N 39049-BELOW Pub 11-04 ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
0891020100 02957510 00768968 00766611 00770781 00770777 02963669 00755881 0891030100 15B2000 00036900 00766603 00765337 00013701 00013600 00130010 00756750 02961453 0891030201 00756760 00750621
1 1 1 1 4 4 2 2 1 1 1 1 2 2 2 1 1 1 2 1 2
TAIL WHEEL BEAM WELDMENT BOLT NUT GAUGE WHEEL MOUNT WELDMENT BOLT NUT BOLT NUT CASTER FORK WELDMENT WASHER COTTER PIN SPINDLE LOCK WELDMENT W/NUT SPACER BEARING CONE SEALS TIRE AND WHEEL ASSY - LAMINATED TIRE TIRE, WHEEL, CUPS GREASE FITTING BUSHING WHEEL & TIRE ASSY - MOLDED TIRE (ITEMS 19-21) BEARING CUP
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 9
TAILWHEEL ASSY -LIFT TYPE S/N 39050-40386 & 41507-Current Pub 03-05
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 6 7 8 9 10 11 12 13 14 17
0891020100 02957510 00768968 00766611 00770781 00770777 02963669 00755881 00776224 15B2000 00036900 0891030300 00776217 00776210
1 1 1 1 4 4 2 2 1 1 1 1 2 1
WLDMT T/W BEAM HEXB METRIC 16-P1.5 - 90MM 8 NUT MET TLE 16MM-P1.5 PL WLDMT-GAUGE WHEEL MOUNT HEXB METRIC 14-P1.5- 32MM LOCKNUT METRIC 14MM-P1.5 HEXB METRIC 12-P1.25- 80MM 5 NUT METRIC TLM 12MM-P1.25 PL5 FORK CASTER ASSEMBLY WASHER SAE 1 1/4 PLATED PIN-COTTER 1/4 X 2-1/2 WLDMT, SPINDLE w/NUT WASHER FLAT 026 X 044 X 4 FLAT AG SE CASTER FORK WHEEL ASSY
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 10
MOLDED TIRE ASSY Rev 10-04
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3
02961453 0891030201 00756760
1 2 1
GREASE FITTING 1/4-28 TAPER 45 BUSHING, SINTERED IRON WHEEL,DEMOUNTABLE 16X4X2057(COMPLETE W/ ITEMS 1 & 2)
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 11
CASTER FORK WHEEL ASSY S/N 39050-40386 & 41507-Current Pub 03-05
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6
00776210 373024H 00776214 00776217 00776224 00036900 152B000
1 1 2 1 1 1
AG SE CASTER FORK WHEEL ASSY LAMINATED WHEEL & TIRE ASSY HUB 4 BOLT WASHER FLAT 026 X 044 X 4 FLAT FORK CASTER ASSEMBLY PIN-COTTER 1/4 X 2-1/2 WASHER
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 12
TAIL WHEEL HUB ASSY S/N 39050-40386 & 41507-Current Rev 09-06
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10
00771620 00772017 00772018 00772082 00776211 00776212 00776213 00776215 07762462 00776219
1 2 2 1 1 1 2 4 4 2
PIN,COTTER 5/32X2-1/2 PL BUSHING SPINDLE STEP DUST CAP NIPPLE, GREASE M8X1 BOLT SPINDLE M24 X 2 X 186 NUT SPINDLE M24 X 2 BEARING LUG BOLT FLAT WASHER BOLT M12 X 1.5 X 25 SEAL OIL 40 X 62 X 8
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 13
TONGUE ASSEMBLY - PULL TYPE Rev 08-04
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
00766586 00766587 00775964 7092 00764515 00761037 00761267 00761046 5JRC1490 00776701 15B1400 02793900 00755881 00766086 00770776 00760820 00775967
1 1 1 1 1 1 1 1 2 2 2 2 8 8 8 1 1
HITCH EAR PLATE LH HITCH EAR PLATE RH TONGUE WELDMENT JACK CHAIN ADJUSTMENT BOLT ADJUSTMENT BUSHING TRUNION LOCKNUT BUSHING WASHER BOLT LOCKNUT FLATWASHER BOLT NUT NUT
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 14
THIS PAGE INTENTIONALLY LEFT BLANK
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 15
TAIL WHEEL ASSEMBLY - PULL TYPE Rev 08-04
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 16
TAIL WHEEL ASSEMBLY - PULL TYPE Rev 08-04 ITEM
PART NO.
QTY.
DESCRIPTION
1
00130010 00756760 00765337 0891030300 5JRC16140 00776008 7A16824 02030300 00775963 02918600 15B1200 00037200 00554600 8354 00606000 8527 00775996 02845700 00695100 00775967 00767294 511016
2 2 4 2 2 1 2 2 1 3 3 3 1 1 2 1 2 2 2 1 1 2
WHEEL & TIRE ASSEMBLY - LAMINATED WHEEL & TIRE ASSEMBLY - SOLID BUSHING SPINDLE WELDMENT LOCKNUT AXLE LUG BOLT LOCKNUT AXLE WELDMENT BOLT WASHER LOCKNUT RATCHET PIVOT PIN SHORT COTTER PIN PIVOT PIN LONG AXLE CYLINDER LUG BOLT LOCKNUT LEVEL ROD BUSHING BUSHING
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 17
GEARBOX ASSEMBLY Rev 09-05
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 18
GEARBOX ASSEMBLY Rev 09-05 ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 25 26 27
00775857 00775858 00775859 00564600 00564200 00775860 00564100 00775862 00780498 00780497 00760929 00760828 00755954 9313055 00758692 00606000 00563500 00757683 00757682 00564000 00563700 00564800 00769321 00770737 7192 7A81324 00001800 00765444
1 1 1 1 1 1 3 1 var. var. var. var. 10 10 1 1 1 1 1 1 3 1 2 2 1 1 1 1qt
GEARBOX ASSY HOUSING INPUT CAP 22 TOOTH GEAR INPUT SEAL INPUT SHAFT RETAINING RING GEAR SPACER INPUT GASKET (0.30) INPUT GASKET (0.13) INPUT GASKET (0.30) INPUT GASKET (0.13) LOCKWASHER BOLT SLOTTED FLANGE NUT COTTER PIN OUTPUT SEAL OUTPUT CAP OUTPUT BEARING SPACER 15 TOOTH OUTPUT SHAFT & PINION BALL BEARING BALL BEARING SEALING WASHER PLUG SNAP RING BOLT LOCKNUT QT,ALAMO 000 GEAR LUBE
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 19
SHIELD ASSEMBLY - U-JOINT
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5
00766581 00766559 00766086 00755881 00770066
1 1 1 1 1
SHIELD BRACKET FLATWASHER NUT CABLE & PIN ASSEMBLY
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 20
BLADE PAN ASSEMBLY
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5
00761358 00761357 00786629 00761402 00761535 00750226
1 1 2 2 2 2
PAN ASSY PAN BLADE KIT BLADE BOLT WASHER LOCKNUT
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 21
DRIVELINE ASSEMBLY S/N 39375 -CURRENT Pub 10-04
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 22
DRIVELINE ASSEMBLY S/N 39375 -CURRENT Pub 10-04 ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
00759318C 00764500A 00756231 ------------00759169 ------------------------00759165 ------------00773087 00764506 00754330 00764507 00768342 00754303 00773080 00773081 00768347 00773082 00768346 00754316 ------------------------------------------------00768294 00768339 ------------------------00774079
1 2 1 1 1 1 1 1 1 1 6 1 1 8 1 1 2 1 1 8 1 1 1 1 1 1 1 1 1
DRIVELINE SC SER.40 SE5 ASY,YOKE COLLAR - COMPLETE CROSS & BEARING KIT SERIES 40 OUTER YOKE PIN ROLL 8mm X 60mm OUTER TUBE WITH LABEL INNER TUBE PIN ROLL INNER TUBE INNER YOKE CLUTCH 1-3/8 BORE, SERIES 40 COLLAR-INNER-GUARD-RETAINER BOLT, NYLON - SAFETY SHIELD] COLLAR-OUTER-GUARD-RETAINER SHIELD, ASY, CMPLT SPRING CLUTCH YOKE FLANGED FOR 00773087 CLU BUSHING FOR 00773087 CLUTCH DISK, CLUTCH CLUTCH SUPPORT W/1-3/8 BORE PLATE, CLUTCH PRESSURE NUT & BOLT M10X80 FEMALE TUBE YOKE WITH LABEL MALE TUBE YOKE HALF FEMALE GUARD HALF MALE GUARD SHAFT, ASY, OUTER W/SHIELD SHAFT, ASY, INNER W/SHIELD DANGER LABEL FOR OUTER TUBE DANGER LABEL FOR OUTER GUARD TUBE KIT,SLIDE COLLAR REPAIR
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 23
DRIVELINE ASSEMBLY - SHEAR PIN S/N 39824-BELOW Rev 10-04
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 24
DRIVELINE ASSEMBLY - SHEAR PIN S/N 39824-BELOW Rev 10-04 ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14
00759161B 00768296 001465 00768257 00756231 00768295 00768294 00768293 00770391 00759170 00764506 00754330 00764507 00775112 00775113
1 1 1 2 1 1 1 1 1 1 6 1 1 1
DRIVELINE ASSEMBLY INNER SHAFT & SHIELD ASSY GREASE FITTING SHEAR BOTL YOKE CROSS & BEARING KIT INNER TUBE ASSEMBLY OUTER SHAFT & SHIELD ASSY OUTER TUBE ASSEMBLY TWIST COLLAR KIT YOKE ASSEMBLY INNER TUBE BEARING LOCKING PIN OUTER TUBE BEARING INNER HALF SHIELD ASSEMBLY OUTER HALF SHIELD ASSEMBLY
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 25
DRIVELINE ASSEMBLY - SLIP CLUTCH S/N 39374 -BELOW Rev 10-04
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 26
DRIVELINE ASSEMBLY - SLIP CLUTCH S/N 39374 -BELOW Rev 10-04 ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13
00759318B 00768339 00768340 00756231 00768295 00768294 00768293 00770391 00759170 00764506 00754330 00764507 00768341 00775113
1 1 2 1 1 1 1 1 1 6 1 1 1
DRIVELINE ASSEMBLY INNER SHAFT & SHIELD ASSY SLIP CLUTCH CROSS & BEARING KIT INNER TUBE ASSEMBLY OUTER SHAFT & SHIELD ASSY OUTER TUBE ASSEMBLY TWIST COLLAR KIT YOKE ASSEMBLY INNER TUBE BEARING LOCKING PIN OUTER TUBE BEARING INNER HALF SHIELD ASSEMBLY OUTER HALF SHIELD ASSEMBLY
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 27
DRIVELINE ASSEMBLY S/N 39825 -CURRENT Rev 09-05
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
00759161C 00764500A 00756231 ---------------00759169 ------------------------------00759165 ---------------00777329A 00764506 00754330 00764507 00768342 ------------------------------------------------------------00768294 00768296 ------------------------------00774079
1 2 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 1
DRIVELINE ASY,YOKE COLLAR - COMPLETE CROSS & BEARING KIT SERIES 40 OUTER YOKE PIN ROLL 8mm X 60mm OUTER TUBE WITH LABEL INNER TUBE PIN ROLL INNER TUBE INNER YOKE YOKE, 1-3/8 BORE SP COLLAR-INNER-GUARD-RETAINER BOLT, NYLON - SAFETY SHIELD] COLLAR-OUTER-GUARD-RETAINER SHIELD, ASY, CMPLT FEMALE TUBE YOKE WITH LABEL MALE TUBE YOKE HALF FEMALE GUARD HALF FEMALE GUARD SHAFT, ASY, OUTER W/SHIELD SHAFT, ASY, INNER W/SHIELD DANGER LABEL FOR OUTER TUBE DANGER LABEL FOR OUTER GUARD TUBE KIT,SLIDE COLLAR REPAIR
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 28
DRIVELINE
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
00775835 00775353 00189700 00756934 00775317 00775375 00775838 00775318 00775462 ------------------------8393 00775463 00756005 00756004 00759217
1 2 2 1 1 1 1 1 2 1 1 2 1 1 1 2
DRIVELINE YOKE CROSS BEARING KIT SPRING PIN INBOARD YOKE INNER PROFILE OUTER PROFILE INBOARD YOKE YOKE SHIELD CONE OUT. SHIELD TUBE OVL INN. SHIELD TUBE RND BEARING RING ZERK- IN ITEM 8 DECAL OUT-IN ITEM 10 DECAL INN-IN ITEM 6 SCREW- IN ITEM 9
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 29
SLIP CLUTCH ASSEMBLY S/N 39374 -BELOW Rev 10-04
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8
00768340 00768349 00756024 00768348 00768347 00768346 00762523 00768345 00768344
1 8 8 2 1 8 1 1
SLIP CLUTCH ASSEMBLY FLANGE YOKE LOCKNUT SPRING DISK PRESSURE PLATE BOLT SUPPORT HUB FLANGE YOKE
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 30
DEFLECTOR ASSEMBLY - FRONT Rev 06-05
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12
00775873 00015800 00011400 00011100 00001400 00695100 02675800 00758240 00775851 02035800 00778904 02030700 00001800
8 8 8 4 4 4 1 2 8 1 2 2
FRONT DEFLECTOR ASSY NUT BOLT FLATWASHER WASHER LOCKNUT BOLT DEFLECTOR MOUNT SIDE DEFLECTOR FLATWASHER FRONT DEFLECTOR PANEL BOLT NUT
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 31
DEFLECTOR ASSEMBLY - REAR
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10
00775510 00773667 00773663 00773659 00773658 002030700 00752860 00002700 00001800 00775653 00775654
1 1 1 2 4 22 1 17 23 1 1
COMPLETE DEFLECTOR ASSY DEFLECTOR, LEFT DEFLECTOR, RIGHT DEFLECTOR PANEL DEFLECTOR BAR BOLT BOLT FLATWASHER LOCKNUT RIGHT MOUNT PLATE LEFT MOUNT PLATE
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 32
CHAIN GUARD ASSEMBLY - FRONT (OPTION)
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8
00775871 00775870 00775869 00775739 00001400 00695100 02675800 02030700 00001800
1 1 2 4 4 4 2 2
ASY MAIN FRT CG LH CHAIN GUARD ASSEMBLY, COMPLETE ASY FRONT RH C/G DEFLECT SIDE FORMED WASHER LOCKNUT HHCS 5/8-11UNC 1-1/2 PL5 HHCS 1/2-13UNC 1-1/4 PL5 NUT
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 33
CHAIN GUARD ASSEMBLY - REAR (OPTION)
ITEM
1 2 3 4 5 6 7 8
PART NO.
QTY.
DESCRIPTION
00775643 00775512 00773667 00773663 00775512 02030700 00001800 00002700 7B81332 00775653 00775654
1 2 Ref. 1 1 2 22 23 17 1 1 1
COMPLETE CHAIN GUARD ASSY CHAIN & BAR ASSEMBLY (INCL. ITEMS 3,4 &5) CHAINGUARD DEFLECTOR LEFT CHIANGUARD DEFLECTOR RIGHT ASY, REAR CHAINGUARD HHCS 1/2-13UNC 1-1/4 PL5 LOCKNUT BOLT HHCS 1/2 NC 4 PLATE, RH C/G MOUNT PLATE, LH C/G MOUNT
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 34
CHECK CHAIN ASSEMBLY (EXTRA EQUIPMENT)
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4
3570 8709 8708 02845500 00695100
1 2 2 2 2
CHECK CHAIN ASSY CHAIN ASSEMBLY BRACKET BOLT NUT
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 35
OFFSET ADAPTER THREE-POINT (EXTRA EQUIPMENT)
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
0702310000 0702310100 0702310001 0702310300 0702310200 511027 7A14924 15B1400 423013 5JRC1490 3W6 02030400 00001300 00001200 7AH5121636 595062 00748539 7AH5101816 00749136 743013
1 1 1 1 1 2 2 4 4 2 2 4 4 4 1 1 1 2 2 2
OFFSET ADAPTER ASSY ADAPTER MAINFRAME BRACE BAR BRACE LUG AND CHAIN ADJUSTABLE LIFT LUG WRIST PIN BOLT WASHER BUSHING LOCKNUT RETAINING PIN BOLT LOCKWASHER HEX NUT BOLT SPACER LOCKNUT BOLT LOCKNUT BUSHING
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 36
SAFETY DECAL SHEETS
ITEM
PART NO.
QTY.
DESCRIPTION
1 2 3
00776481 00773311 2738332
1 1 2
SHEET,MANUALCANISTER DECAL KIT, DECAL SHEET SE-5 DECAL, RED OBLONG REFLECTOR (NOT SHOWN)
SE5 (Mar-05) S/N 41507- Current Rev 09-06 ©2007 Alamo Group Inc.
Parts Section – 37
SERVIS-RHINO LIMITED
WARRANTY
1. LIMITED WARRANTIES 1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) Repair or replace the defective goods or part(s) or (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Servis-Rhino Implement Model _______________________________ Serial Number ________________________________ Date Purchased __________________________________________ Dealer ______________________________________ ATTENTION: READ YOUR OPERATOR'S MANUAL
RHINO®
1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email:
[email protected]
R
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. 2. 3. 4.
Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and Ensure that each employee uses such Seatbelt while the tractor is moving; and Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS.
REQUIRED OF THE OPERATOR 1. 2. 3. 4. 5. 6. 7. 8. 9.
Securely fasten seatbelt if the tractor has a ROPS. Where possible, avoid operating the tractor near ditches, embankments, and holes. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. Stay off slopes too steep for safe operation. Watch where you are going - especially at row ends, on roads, and around trees. Do not permit others to ride. Operate the tractor smoothly - no jerky turns, starts, or stops. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery guards in place...
Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
SE5 PL 03/05 Printed U.S.A.
P/N 00768613P
