 Installation guide You just bought the Stainless steel projector colour OR white from the SeaMAID range. Thank you for your trust. Follow this guide for an easy and quick installation.

STAINLESS STEEL PROJECTOR References White 500873 and 501207 References RGB 500880 and 501214

 Presentation of the product

This ~12V flat LED lighting system has been designed for all types of fountains, fresh water sources and gardens.

4

2 3 4

3

1 Stainless steel projector

Junction box

Cable

Transformer

1

2

3

4

~12V MAX

> Installation A step by step assistance

Recommendations For a correct installation, the projector power socket will have to possess a protection device by residual current with a maximum intensity of 30 mA. This projector will only be connected to a safety isolating transformer with double winding and a maximum output voltage of 12VAC. Another type of transformer is prohibited. This transformer power will always be higher by at least 20% to the total power of the connected projector.

This projector will be connected to the ~12VAC power cable from the transformer in a sealed box. The minimum cross section of the cable will be 2x1,5mm² with a conduit suitable for an outdoor use. This projector can be installed to light a fountain, a pond, a natural pool immersed in fresh water at a maximum immersion depth of 1 meter. It can be also used to light a plant massif, a rocky area or other part of the garden. Handle the projectors with care and on a clean cloth support.

> Installation A step by step assistance 1. Before any operation, cut the power supply from the safety isolating transformer.

2. Connect the projector cable to the ~12V power cable in the provided sealed connection box.

3. Secure the projector to the chosen location.

4. Assure that the power supply voltage is only ~12V 5. In case of immerged use, check the support sealing

6.

Switch on the projector

CAUTION : DO NOT CONNECT TO THE MAIN 220/230V POWER GRID. IT WOULD CAUSE IRREVERSIBLE DAMAGES

> Use RGB 500880 and 501214 models, 16 On/Off programs Manual program with 11 static colours and 5 controlled atmospheres The RGB On/Off stainless steel projector control is manual, using the on/off switch of the projector power. A cut of the current of less than 2 seconds makes the program change. After a cut of the current for over 10 seconds, switch on restarts from the last program used.

Recommendations :

For the first use, the stainless steel projector lights on the program 1 (all LED lit). Then you go to the 11 static colours, followed by 5 automatic programs.

In all cases, refer to the leaflet provided with the product.

It is as well possible to use a ~12V radio switch and install it on the ~220V/12V safety isolating transformer output.

In case of difficulty during the installation or use, it is recommended to watch the installation video and to read the FAQ on our website.

To be synchronized on the On/Off manual mode, the colour projectors must be connected to the same power supply.

> Accessories

> Grass plug

Find here the compatible and recommended accessories SeaMAID low voltage radio switch:

To be used in place of the stainless steel plate for a better fixing in the ground or turf

To control 1 to 12 lamps, choose between the 1 and 4 channel module to install on the ~12V power supply. Model 501078

Recommendations : Discover the online SeaMAID range products Model 500743

Model 500750

> SeaMAID power supply box: Special power box for the SeaMAID range low voltage LED projectors, ~220/230V – 12V with 100W safety transformer Model 500996

In case of difficulty during theinstallation or the use, it is recommended to watch the installation video and read the FAQ on our website.

> SeaMAID, proof of quality and reliability

> Quality: SeaMAID products are developed exclusively by our French R&D team then manufactured in China and marketed after a rigorous quality-control. SeaMAID products range is certified TÜV Rheinland thus proving the safety and quality of the proposed products.

> Reliability : Each SeaMAID product is guaranteed 24 months in standard exchange. Thanks to an exclusive development, the optics brings a confort in the use of the products; plastic parts are soldered by friction thus ensuring a perfect seal.