HEAVY DUTY MOTORS

HEAVY DUTY HYDRAULIC MOTORS

CONTENTS Page

•

Hydraulic Motors Series MSWM ........................................................................................ 4

•

Hydraulic Motors Series MTM ................................................................................... 8

•

Hydraulic Motors Series TMF ................................................................................... 20

•

Hydraulic Motors Series MVM .................................................................................. 25

•

Hydraulic Motors Series VMF ................................................................................... 30

•

Motor Special Features............................................................................................... 34

•

Motors with Speed Sensor................................................................................................... 35

•

Application Calculation ...................................................................................................... 37

“M+S HYDRAULIC” can accept no responsibility for possible errors in catalogues, brochures and other printed material. “M+S HYDRAULIC” reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.

DISC VALVE HYDRAULIC MOTORS GENERAL INFORMATION: Orbit motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Hydraulic orbit motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into motor which is then delivered via the motor's output shaft. Orbit motors have high starting torque and constant output torque at wide speed range. The output shaft runs on tapered roller bearings and can absorb high axial and radial forces. DISTRIBUTOR VALVE MSEM, MTM, TMF, MVM, VMF series motors have disk valve: the distributor valve has been separated from output shaft and is driven by short cardan shaft. A balance plate counterbalances the hydraulic forces around the distributor valve. It gives the motors high efficiency- even at high pressures, and good starting characteristics. GEAR WHEEL SET There are two forms of gear wheel set: Gerotor set have plain teeth and Roll-gerotor set with teeth fitted with rollers. MSEM, MTM, TMF, MVM, VMF series motors have roll-gerotor set. The rollers reduce local stress and the tangential reaction forces on the rotor reducing friction to a minimum. This gives long operating life and better efficiency even at continuous high pressures.

FEATURES: Standard Motor The standard motor mounting flange is located as close to the output shaft as possible. This type of mounting supports the motor close to the shaft load. This mounting flange is also compatible with many standard gear boxes.

Wheel Motor The wheel motor mounting flange is located near the center of the motor which permits part or all of the motor to be located inside the wheel or roller hub. In traction drive applications, loads can be positioned over the motor bearings for best bearing life. This wheel motor mounting flange provides design flexibility in many applications.

Short Motor This motor is assembled without the output shaft, bearings and bearing housing and has the same drive components as the standard motors. The short motor is especially suited for applications such as gear boxes, winch, reel and roll drives. Short motor applications must be designed with a bearing supported internal spline to mate with the short motor drive. Product designs using these hydraulic motors provide considerable cost savings.

LL Series hydraulic motors are designed to operate at the whole standard range of working Low Leakage conditions (pressure drop and frequency of rotation ), but with considerable decreased volumetric losses in the drain ports. This motors are suitable for hydraulic systems with series-conected motors with demands for low leakage.

LSV feature optimizes the motor for low-speed performance. Motors with this valving provide very Low Speed Valve low speed while maintaining high torque. They are designed to run continuously at low speed (up to 200 RPM) at normal pressure drop and reduced flow. Optimal run is guaranteed at frequency of rotation from 20 to 50 RPM . Motors with this valving have an increased starting pressure and are not recommended for using at pressure drop less than 40 bar. Motors with Speed Sensor

Motors are available with integrated inductive speed sensor. The output signal is a standardized voltage signal that can be used to control the speed of a motor. The torque and the radial load of the motor are not affected by the installation of speed sensor.

3

HYDRAULIC MOTORS MSWM APPLICATION » » » » » » » »

Sawmill machines Woodworking machines Metal working machines Agriculture machines Road building machines Mining machinery Food industries Special vehicles etc.

CONTENTS

OPTIONS

Specification data ....................................... 5 Dimensions and mounting ...........................6 Permissible shaft loads .............................. 6 Shaft extensions ......................................... 7 Order code ................................................. 7

» Model- Disc valve, roll-gerotor » Wheel mount » Side and rear ports » Shafts- straight, splined and tapered » Metric and BSPP ports » Other special features

GENERAL Max. Displacement,

3

3

397 [24.2]

cm /rev [in /rev]

Max. Speed,

560

[RPM]

Max. Torque,

daNm [lb-in]

Max. Output,

kW [HP]

Max. Pressure Drop, Max. Oil Flow,

cont.: 90 [7965]

24 [32.2 cont.: 200 [2900]

bar [PSI]

5

[RPM]

Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)

Pressure fluid O

Temperature range,

-40÷140 [-40÷284]

O

C [ F]

20÷75 [98÷347]

2

Optimal Viscosity range, mm /s [SUS]

ISO code 20/16 (Min. recommended fluid filtration of 25 micron)

Filtration

p

Oil flow in drain line

Oil flow in Pressure drop Viscosity drain line 2 bar [PSI] mm /s [ SUS] lpm [GPM ] 140 [2030] 210 [ 3045]

int: 225 [3270]

90 [24]

lpm [GPM]

Min. Speed,

int: 110 [9735]

20 [ 98 ]

1,5 [ .396 ]

35 [ 164 ]

1 [ .264 ]

20 [98]

3 [ .793 ]

35 [164]

2 [ .528 ]

Pressure Losses

p

bar

PSI

14 12 10 8 6 4

200 150 100 50

2 0

0

4

0

2.5

5

0

10

20

7.5

30

10

40

12.5

50

15

60

17.5

70

20

22.5 Q, GPM

80

90 Q, lpm

MSWM EPMS MOTORS MOTORS

SPECIFICATION DATA

MSWM 160

Type Displacement, cm3/rev. [in3/rev.]

MSWM 200

159,7 [ 9.74 ] 200 [12.2]

MSWM 250

MSWM 315

MSWM 400

250 [15.3] 19.2 [314,9] 397 [24.2]

Max. Speed,

cont.

470

375

300

240

185

[RPM]

Int.*

560

450

360

285

225

Max. Torque

cont.

46 [ 4070 ]

daNm [in- lb]

Int.*

51,5 [ 4560 ] 64,5 [5710] 80,6 [7135] 96,0 [8500] 97,0 [8585]

peak**

51,5 [ 4560 ]

Max. Output

cont.

18, 6 [24. 9 ] 18,1 [24.3] 18,0 [24.1] 17,0 [22.8] 11,0 [14.7]

kW [HP]

int.*

24,0 [32.2] 24,0 [32.2] 23,8 [31.9] 20,2 [27.1]

Max. Pressure Drop

cont.

200 [2900] 200 [2900] 200 [2900] 200 [2900] 160 [2320]

bar [PSI]

Int.*

225 [3270] 225 [3270] 225 [3270] 22 0 [3 19 0] 175 [2540]

peak**

225 [3270] 225 [3270] 225 [3270] 225 [3270] 200 [2900]

56,6 [5010] 70,8 [6270] 90,0 [7965] 90,0 [7965] 65 [5755] 80,6 [7135] 108 [9560] 110 [9735] 12 [16.1]

Max. Oil Flow

cont.

75 [20]

75 [20]

75 [20]

75 [20]

75 [20]

lpm [GPM]

Int.*

90 [24]

90 [24]

90 [24]

90 [24]

90 [24]

Max. Inlet Pressure

cont.

210 [3045] 210 [3045] 210 [3045] 210 [3045] 210 [3045]

bar [PSI]

Int.*

250 [3625] 250 [3625] 250 [3625] 250 [3625] 250 [3625]

peak**

300 [4350] 300 [4350] 300 [4350] 300 [4350] 300 [4350]

Max. Return Pressure

cont.

140 [2030] 140 [2030] 140 [2030] 140 [2030] 140 [2030]

with Drain Line

Int.*

175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540]

bar [PSI]

peak**

210 [3045] 210 [3045] 210 [3045] 210 [3045] 210 [3045]

Max. Starting Pressure with Unloaded Shaft, bar [PSI] Min. Starting Torque daNm [in- lb] Min. Speed***, [RPM]

10 [1 4 5]

10 [1 4 5]

10 [1 4 5]

10 [1 4 5]

10 [1 4 5]

36,9 [ 3270 ] 46,2 [4090] 58,0 [5135] 73,8 [6530] 72,0 [6370] 6

6

6

5

5

* Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better. 3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4). If using synthetic fluids consult the factory for alternative seal materials. 2 4. Recommended minimum oil viscosity 13 mm /s [70 SUS] at 50°C [122°F]. 5. Recommended maximum system operating temperature is 82°C [180°F]. 6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

5

MSWM EPMS MOTORS MOTORS

DIMENSIONS AND MOUNTING DATA max L

L1

4xø13,5 [.531]

P(A,B) 16±0,3 [.63±.0118] 21±0,3 [.827±.0118]

54 [2.126]

9 [.354]

max 139 [5.47] 16±0,3 [.63±.0118] 21±0,3 [.827±.0118]

102 [4.016]

ø125 -0,063 [4.921-.0025 ] ø85 [3.346

160

T 44 [1.732]

C

22±0,3 [.866±.0118]

5±0,15 [.197±.0059]

41 [1.614]

L2

ø160±0,2 [6.299±.0078]

27±0,3 [1.063±.0118]

C: 2xM10-12 mm [.47 in] depth P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged) Type

E Rear Ports 53 [2.086]

53 [2.086] max 139 [5.47]

P(A,B) 32±0,3 [1.26±.0118]

max 128 [5.039] max 96,5 [3.8] for M shaft

L, mm[in.] L2, mm[in.] L1, mm[in.]

MSWM 160 170,5 [6.71] 129,3 [5.09] 27,8 [1.09] MSWME 160 177,5 [6.99]

Port B

MSWM 200 177,5 [6.99] 136,3 [5.37] 34,8 [1.37] MSWME 200 184,5 [7.26]

Port A 32±0,3 [1.26±.0118]

MSWM 250 186,0 [7.32] 145,0 [5.71] 43,5 [1.71] MSWME 250 193,0 [7.60] MSWM 315 197,5 [7.78] 157,3 [6.19] 54,8 [2.16] MSWME 315 206,5 [8.13]

Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

MSWM 400 212,0 [8.35] 171,0 [6.73] 69,4 [2.73] MSWME 400 219,0 [8.62]

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

PERMISSIBLE SHAFT LOADS The output shaft runs in tapered bearings that permit high axial and radial forces. Curve "1" shows max. radial shaft load at bearing life of 2000 hours at 100 RPM. Curve "2" shows max. radial shaft load at bearing life of 3000 hours at 200 RPM. Pr daN

8000

-.5

0

.5

1

1.5

2

2.5

3

3.5

4

4.5

in 5

Pr lbs 18000

7000

16000

6000

14000 12000

5000 4000

3000

1

10000

2

8000

6000

2000

4000

1000 0 -20

2000 -10

0

10

20

30

40

50

60

6

70

80

90

100 110 120 mm

mm [in]

MSWM EPMS MOTORS MOTORS

SHAFT EXTENSIONS

C -ø40 straight, Parallel key A12x8x70 DIN 6885

K -tapered 1:10, Parallel key B12x8x28 DIN 6885

Max. Torque 132,8 daNm [11755 ln-in]

Max. Torque 210,7 daNm [18650 lb-in]

A-A

12 -0.043

82 -0,2 [3.228-.0079]

M12 min 25 [.984] deep

ø56 [2.205]

[1.5 -.001 ]

ø38,1 -0,025

45 0

56 +2 [2.205 +.079 ]

ø45 [1.771]

[1.5 -.0019]

ø38,1 -0,05

9

[.354]

Max. Torque 132,8 daNm [11755 ln-in]

45 0

ø45 [1.771]

54±0,4 4 [2.126±.016] [.157] 82±0,2 [3.228±.0079]

SH -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976

Max. Torque 132,8 daNm [11755 ln-in]

42,4 -0,2 [1.669-.0079 ]

A

Taper 1:10

CO-ø1½" straight, Parallel key 3 8"x 3 8"x 2¼" BS46

M30x2

ø6,3 [.248]

82 -0,2 [3.228-.0079]

3/8-16 UNC min 25 [.984] deep

S=46 Tightening torque 50±3 daNm [4425±265 lb-in]

ø45 [1.771]

24,15 -0,2 [.95 -.0079]

+0,018

ø40 +0,002

M12 min 25 [.984] deep

9.545 -0,02 [.379-.0008]

A

[.472-.0017 ]

0

[1.575+.0007 +.0001 ]

45

ø45 [1.771]

43 -0,2

[1.692 -.0079]

[.472-.0017 ]

12 -0.043

82 -0,2 [3.228-.0079]

M -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976 Max. Torque 132,8 daNm [11755 ln-in]

[1.5 -.001 ]

ø45 [1.771]

ø38,1 -0,025

45 0

min 34 [1.34]

52 -0,2 [2.047-.0079]

M12 min 25 [.984] deep

mm [in]

ORDER CODE 1

2

3

4

5

6

MSWM Pos.1 - Port type omit - Side ports E

Pos. 4 - Ports omit M

- Rear ports

Pos.2 - Displacement code 160 200 250 315 400

- BSPP (ISO 228) - Metric (ISO 262)

Pos. 5 - Special Features (see page 34)

- 159,7 cm3/rev [9.74 in3/rev] - 200,0 cm3/rev [12.20 in3/rev] - 250,0 cm3/rev [15.30 in3/rev] - 314,9 cm3/rev [19.20 in3/rev] - 397,0 cm3/rev [24.20 in3/rev]

Pos. 6 - Design Series omit - Factory specified

Pos.4 - Shaft Extensions*

NOTES: * The permissible output torque for shafts must not be exceeded!

- ø40 straight, Parallel key A12x8x70 DIN6885 C 3 3 CO - ø1½ ” straight, Parallel key /8”x /8”x2¼” BS46

The hydraulic motors are mangano-phosphatized as standard.

- ø45 tapered 1:10, Parallel key B12x8x28 DIN6885 K SH - ø1½" splined 17T ANS B92.1-1976 - ø1½" splined 17T ANS B92.1-1976 M 7

HYDRAULIC MOTORS MTM APPLICATION » Skid Steer Loaders » Metal working machines » Trenchers » Augers » Agriculture machines » Road building machines » Special vehicles » Mine machines » Woodworking and sawmill machinery » Conveyors etc.

CONTENTS

» High torque and pressure drop » High inlet pressure » High starting torque » Improved efficiency at high pressure drop » Smooth operation at low speed

3

724,3 [44.2]

cm /rev [in /rev]

Max. Speed,

OPTIONS

EXCELLENCE

GENERAL 3

B

» Model- Disc valve, roll-gerotor » Flange with wheel mount » Short motor » Side ports » Shafts- straight, splined and tapered » BSPP ports; » Other special features.

Specification data ......................................... 9 Function diagrams ................................. 10÷12 Dimensions and mounting ...................... 13÷15 Shaft extensions ............................................ 16 Permissible shaft loads .................................. 16 Dimensions and mounting- MTMV ................. 17 Dimensions and mounting- MTM6V ............... 18 Internal Spline data ....................................... 19 Order code ................................................... 19

Max. Displacement,

A

750

[RPM]

Max. Torque,

daNm [in-lb]

Max. Output,

kW [HP]

Max. Pressure Drop,

bar [PSI]

Max. Oil Flow,

cont.: 183 [16200]

70 [94] cont.: 250 [3600] 5

[RPM]

Permissible Shaft Loads

Pa=1000 [2250]

daN [lbs]

Pressure fluid

int.: 350 [5080]

150 [40]

lpm [GPM]

Min. Speed,

int.: 229 [20270]

Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) O

Temperature range,

O

C [ F]

-40÷140 [-40÷284]

2

20÷75 [98÷347]

Optimal Viscosity range, mm /s [SUS]

ISO code 20/16 (Min. recommended fluid filtration of 25 micron)

Filtration

Pressure Losses Oil flow in drain line

flow in Pressure drop Viscosity Oil drain line bar [PSI] mm 2/s [ SUS] lpm [GPM ] 2,5 [.660 ] 20 [98] 200 [2 90 0] 2 75 [3990]

350

25

300

20

250 200 150

35 [164]

1,5 [ .400]

100

20 [98]

4 [1.057]

50

35 [164]

2,5 [.660]

15 10 5

0

0

0 0

8

25 5

75

50 10

15

20

100 25

125 Q, lpm 30

Q, GPM

MTM MOTORS

SPECIFICATION DATA Type Displacement, 3

3

cm /rev [in /rev]

MTM 200

MTM 250

MTM 315

MTM 400

MTM 470

MTM 500

MTM 630

MTM 725

201,4

251,8

326,3

410,9

475

523,6

631,2

724

[12.29]

[15.36]

[19.9]

[25.06]

[28.97]

[31.95]

[38.52]

[44.2]

Max. Speed,

Cont.

625

500

380

305

260

240

190

170

[RPM]

Int.*

750

600

460

365

315

285

230

215

Max. Torque

Cont.

72[6375] 90[7965] 116[10265] 147[13010] 171[15135] 172[15225] 183[16200] 160[14160]

daNm [in-lb]

Int.*

102[9030] 128[11330] 163[14425] 206[18232] 215[16030] 215[16030] 229[20270] 192[17000]

Peak**

115[10180] 144[12745] 186[16460] 235[20800] 240[21240] 240[21240] 274[24250] 240[21240]

Max. Output

Cont.

41 [55]

41 [55]

41 [55]

41 [55]

41 [55]

37,5[50]

28 [37,5]

26 [35]

kW [HP]

Int.*

70[94]

70[94]

70[94]

70[94]

55[74]

51 [68]

42 [56]

40 [54]

Max. Pressure Drop

Cont.

250[3600] 250[3600] 250[3600] 250[3600] 250[3600] 230[3340] 200[2900] 160[2320]

bar [PSI]

Int.*

350[5080] 350[5080] 350[5080] 350[5080] 315[4570] 280[4060] 250[3625] 210[3045]

Peak**

400[5800] 400[5800] 400[5800] 400[5800] 350[5080] 320[4640] 300[4350] 260[3770]

Max. Oil Flow

Cont.

125[33]

125[33]

125[33]

125[33]

125[33]

125[33]

125[33]

125[33]

lpm [GPM]

Int.*

150[40]

150[40]

150[40]

150[40]

150[40]

150[40]

150[40]

150[40]

Max. Inlet Pressure

Cont.

270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920]

bar [PSI]

Int.*

370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370]

Peak**

420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100]

Max. Return Pressure

Cont.

without Drain Line or

Cont. 100-300 RPM 40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

Cont.

20 [290]

20 [290]

20 [290]

20 [290]

-

-

-

Max. Pressure in Drain Line, bar [PSI]

Int.*

0-100 RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100] >300 RPM 20 [290]

75 [1100] 75 [1100] 75 [1100] 75 [1100]

0-max. RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100]

75 [1100] 75 [1100] 75 [1100] 75 [1100]

Max. Return Pressure

Cont.

270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920]

with Drain Line

Int.*

370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370]

bar [PSI]

Peak**

420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100]

Max. Starting Pressure with Unloaded Shaft, bar [PSI] Min. Starting Torque daNm [in-lb] Min. Speed***, [RPM] Weight, kg [lb]

6 [90]

6 [90]

60[5310] 75[6640] 5

5

6 [90]

6 [90]

6 [90]

6 [90]

6 [90]

6 [90]

97[8585] 122[10800] 142[12570] 143[12655] 145[12830] 148[13100] 5

5

5

5

5

5

MTM

26,9 [59.3] 27,3 [60.2] 28,1 [62]

MTMW

27,4 [60.4] 27,8 [61.3] 28,6 [63.1] 29,5 [65.1] 30,2 [66.6] 30,7 [67.7] 30,2 [66.6] 31,5 [69.5]

MTMV

15,7 [34.6] 16,1 [35.5] 16,9 [37.3] 17,8 [39.3] 18,5 [40.8] 19 [41.9] 18,5 [40.8] 19,8 [43.7]

29 [64]

29,7 [65.5] 30,2 [66.6] 29,7 [65.5] 31 [68.4]

Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds of 5 RPM lower than given, consult factory or your regional manager.

*

1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better. 3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4). If using synthetic fluids consult the factory for alternative seal materials. 4. Recommended minimum oil viscosity 70 SUS [13 mm²/s] at 50°C [122°F]. 5. Recommended maximum system operating temperature is 82°C [180°F]. 6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

9

MTM MOTORS

FUNCTION DIAGRAMS

10000

33 GPM

100

150 l/min

125 l/min

100 l/min

80 l/min

120

39.6 GPM

21.2 GPM

60 l/min

40 l/min

26.4 GPM

10.6 GPM

15.85 GPM

140

p=350 bar 5075 PSI 325 bar 4715 PSI 300 bar 4350 PSI 275 bar 3990 PSI 250 bar 3625 PSI 225 bar 3265 PSI 200 bar 2900 PSI

60 kW 50 kW

int.

12000

20 l/min

M M lb-in daNm

5.3 GPM

Q=10 l/min

2.65 GPM

MTM 250

40 kW

8000 80

4000

2000

0

20 kW 60

cont.

6000

30 kW

10 kW

40

160 bar 2320 PSI

85%

=86%

t

80%

120 bar 1740 PSI

78%

5 kW

N=2,5 kW

20

83%

75%

70%

0

60%

cont.

50

0

100

150

200

250

350

300

400

80 bar 1160 PSI 40 bar 580 PSI

int.

450

500

550

n -1 600 min (rpm)

14000 12000

150

150 l/min

39.6 GPM

100 l/min

33 GPM

26.4 GPM

80 l/min

21.2 GPM

60 l/min

15.85 GPM

40 l/min

10.6 GPM

125 l/min

p=350 bar 5075 PSI 325 bar 4715 PSI 300 bar 4350 PSI 275 bar 3990 PSI 250 bar 3625 PSI 225 bar 3265 PSI 200 bar 2900 PSI

50 kW

int.

16000 175

20 l/min

Q=10 l/min

2.65 GPM

M M lb-in daNm

5.3 GPM

MTM 315

125

40 kW

10000

75

cont.

100 8000

30 kW

6000 4000 2000 0

10 kW

5 kW

20 kW

=88%

160 bar 2320 PSI

t

50

87%

85%

83%

N=2,5 kW

25 0

120 bar 1740 PSI

80%

75% 70% 60%

cont. 0

50

100

150

200

250

300

350

40 bar 580 PSI

int. 400

n 450

The function diagrams data was collected at back pressure 5÷10 bar (72.5PSI÷145PSI) O and oil with viscosity of 32 mm²/s [150SUS] at 50° C [122 F]. 10

80 bar 1160 PSI

500

min-1 (rpm)

MTM MOTORS

FUNCTION DIAGRAMS

18000

200

14000 12000

175

6000 4000

150 l/min

39.6 GPM

125 l/min

100 l/min

33 GPM

26.4 GPM

80 l/min

60 l/min

40 l/min

21.2 GPM

10.6 GPM

40 kW

50 kW

30 kW

150

250 bar 3625 PSI 225 bar 3265 PSI

125

10000 8000

p=350 bar 5075 PSI 325 bar 4715 PSI 300 bar 4350 PSI 275 bar 3990 PSI

60 kW

100

200 bar 2900 PSI

cont.

16000

15.85 GPM

225

int.

20000

20 l/min

M M lb-in daNm

5.3 GPM

Q=10 l/min

2.65 GPM

MTM 400

=87% 5 kW

50

2000

25

0

0

20 kW

10 kW

t

75

160 bar 2320 PSI

86% 85%

N=2,5 kW

120 bar 1740 PSI

78% 83%

80%

80 bar 1160 PSI

75%

70% 60%

40 bar 580 PSI

cont.

0

100

50

200

150

250

int.

300

350

n 400

-1

min (rpm)

12000 10000 8000 6000 4000

33 GPM

150 l/min

125 l/min

100 l/min

26.4 GPM

39.6 GPM

p=350 bar 5075 PSI 325 bar 4715 PSI 300 bar 4350 PSI 275 bar 3990 PSI 250 bar 3625 PSI 225 bar 3265 PSI 200 bar 2900 PSI

50 kW 30 kW

40 kW

150 125 100

cont.

14000

80 l/min

175

21.2 GPM

16000

60 l/min

200

15.85 GPM

18000

40 l/min

225

10.6 GPM

20000

5.3 GPM

250

20 l/min

22000

Q=10 l/min

M daNm

int.

M lb-in

2.65 GPM

MTM 470

10 kW

160 bar 2320 PSI

5 kW

75

=87%

t

50

2000

25

0

0

20 kW

N=2,5 kW

85%

120 bar 1740 PSI

78% 83%

80%

80 bar 1160 PSI

70%

75% 60%

40 bar 580 PSI

cont.

0

50

100

150

200

int.

250

300

The function diagrams data was collected at back pressure 5÷10 bar (72.5PSI÷145PSI) O and oil with viscosity of 32 mm²/s [150SUS] at 50° C [122 F]. 11

n 350

min-1 (rpm)

MTM MOTORS

FUNCTION DIAGRAMS

14000 12000

150

6000 4000

25

0

0

150 l/min

39.6 GPM

33 GPM

125 l/min

100 l/min

80 l/min

160 bar 2320 PSI

80% 83%

=86%

t

50

2000

200 bar 2900 PSI

30 kW

10 kW

cont.

75

26.4 GPM

21.2 GPM

20 kW

125 100

p=325 bar 4715 PSI 300 bar 4350 PSI 275 bar 3990 PSI 250 bar 3625 PSI 225 bar 3265 PSI

50 kW

40 kW

10000 8000

60 l/min

175

15.85 GPM

16000

40 l/min

200

10.6 GPM

18000

20 l/min

225

5.3 GPM

20000

Q=10 l/min

M daNm

int.

M lb-in

2.65 GPM

MTM 500

78%

5 kW

N=2,5 kW

120 bar 1740 PSI

75%

80 bar 1160 PSI

70% 60%

cont.

0

50

100

150

40 bar 580 PSI

int.

200

250

n 300

-1

min (rpm)

14000 12000 10000 8000 6000

2000 0

0

150 l/min

160 bar 2320 PSI

20 kW 85%

75

25

39.6 GPM

10 kW

100

4000

225 bar 3265 PSI

40 kW

200 bar 2900 PSI

150

50

125 l/min

30 kW

175

125

33 GPM

100 l/min

80 l/min

26.4 GPM

21.2 GPM

250 bar 3625 PSI

cont.

16000

60 l/min

200

15.85 GPM

18000

40 l/min

225

10.6 GPM

20000

5.3 GPM

250

20 l/min

22000

Q=10 l/min

M daNm

int.

M lb-in

2.65 GPM

MTM 630

N=2,5 kW

5 kW

83%

78% 80%

120 bar 1740 PSI

75%

=87%

80 bar 1160 PSI

t

70% 40 bar 580 PSI

60% cont.

0

25

50

75

100

125

150

175

int.

200

225

The function diagrams data was collected at back pressure 5÷10 bar (72.5PSI÷145PSI) O and oil with viscosity of 32 mm²/s [150SUS] at 50° C [122 F]. 12

n 250

min-1 (rpm)

MTM MOTORS

DIMENSIONS AND MOUNTING DATA - MTM and MTMC

82,5 [3.248]

[2.181]

55,4

Flange Dim. See Page 15

SH Shaft

82 [3.228]

82 [3.228]

40...40,4 [1.575...1.59]

K Shaft C,CO Shaft

Shaft Dim. See Page 16

82 [3.228]

SH Shaft

30,8...31,2 [1.212...1.228]

C,CO Shaft

82 [3.228]

K Shaft

T

L2

max L

ø139 [5.472]

L1

ø139 [5.472]

L1

max L

L2

T

21±0,15 [.827±.0059]

P(A,B)

P(A,B)

42±0,15 42±0,15 [1.653±.0059] [1.653±.0059]

Port A

T - Drain port

Port B

F

ø21 +0,4 G1/4

12 [.472]

F

[.827 +.0157 ]

1 [.0394]

139 [5.472]

72

[2.834]

Warning: Drain line should always be used. P(A, B): 2xG3/4 - 17 mm [.669 in] depth T : G1/4 - 12 mm [.472 in] depth (plugged) Type MTM 200 MTM 250 MTM 315 MTM 400 MTM 470 MTM 500 MTM 630 MTM 725

Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

L, mm [in] 188 [7.40] 194 [7.64] 203 [7.99] 214 [8.43] 222 [8.74] 228 [8.98] 224 [8.82] 233 [9.17]

L2, mm [in] 142,3[5.60] 148,6 [5.85] 157,8 [6.21] 168,3 [6.63] 176,3 [6.94] 182,3 [7.18] 178,3 [7.02] 187,3 [7.37]

Type MTMC 200 MTMC 250 MTMC 315 MTMC 400 MTMC 470 MTMC 500 MTMC 630 MTMC 725

L, mm [in] L2, mm [in] 198 [7.79] 153 [6.02] 204,5 [8.05] 159,3 [6.27] 213,5 [8.40] 168,5 [6.63] 224 [8.82] 179 [7.04] 232 [9.13] 187 [7.36] 238 [9.37] 193 [7.60] 234 [9.21] 189 [7.44] 243 [9.56] 198 [7.79]

L1, mm [in] 25 [.98] 31,3 [1.23] 40,5 [1.59] 51 [2.01] 59 [2.32] 65 [2.56] 61 [2.40] 70 [2.76]

mm [in] 13

MTM MOTORS

DIMENSIONS AND MOUNTING DATA - MTMW

K Shaft

C, CO Shaft

SH Shaft

82

[3.228]

[3.905...3.929]

Flange Dim. See Page 15

L1

ø139 [5.472]

Port Dim. See Page 13

max L

L3

L2

99,2...99,8

82 [3.228]

Shaft Dim. See Page 16

P(A,B)

Port A

Warning: Drain line should always be used.

P(A, B): 2xG3/4 - 17 mm [.669 in] depth T : G1/4 - 12 mm [.472 in] depth (plugged)

Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

T

Port B

Type MTMW 200 MTMW 250 MTMW 315 MTMW 400 MTMW 470 MTMW 500 MTMW 630 MTMW 725

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

L, mm [in] L1, mm [in] L2, mm [in] L3, mm [in] 129 [5.08] 25 [.98] 83,8 [3.30] 111,1 [3.37] 135 [5.32] 31,3 [1.23] 90,1 [3.55] 117,4 [4.62] 144 [5.67] 40,5 [1.59] 99,3 [3.91] 126,6 [4.98] 155 [6.10] 51 [2.01] 109,8 [4.32] 137,1 [5.40] 163 [6.42] 59 [2.32] 117,8 [4.64] 145,1 [5.71] 169 [6.65] 65 [2.56] 123,8 [4.87] 151,1 [5.95] 165 [6.50] 61 [2.40] 119,8 [4.72] 147,1 [5.79] 174 [6.85] 70 [2.76] 128,8 [5.07] 156,1 [6.15]

mm [in] 14

MTM MOTORS

MOUNTING 4-Bolt flange spigot diameter ø160 mm [6.3 in] - BC ø200 [7.874 in] mm

ø160 -0,063

180 [7.086]

[6.299 -.0025]

40,2 [1.582]

9 [.354]

ø139 [5.472]

ø200±0,4 [7.874±.0157]

ø98±0,5 [3.858±.0197]

4xø18±0,15 [.708±.0059]

24 [.945]

C 4-Bolt flange spigot diameter ø125 mm [4.921 in] - BC ø160 mm [6.3 in] ø160±0,4

-.0004] [4.921-.0019

147 [5.787]

-0,01

ø125 -0,05

9±0,5 [.354±.0197]

[6.3±.0157] R16 [.63]

ø125 -0,1

[.551+.0039 +.0118 ]

[4.921-.0039]

+0,1 4xø14 +0,3

21±0,5 [.827±.0197]

W 4-Bolt flange, Wheel Motor spigot diameter ø160 mm [6.3 in] - BC ø200 mm [7.874 in]

42 [1.653]

4 [.157]

15

21 [.827]

ø160 -0,063

ø172 -0,063

7 [.275]

[6.299 -.0025]

ø200±0,4 [7.874±.0157]

[6.772 -.0025]

180 [7.086]

4xø18±0,15 [.708±.0059]

mm [in]

MTM MOTORS

SHAFT EXTENSIONS

C - ø40 straight, Parallel key A12x8x70 DIN 6885

SH - ø1½" splined 17T, DP 12/24 ANSI B92.1-1976

Max. Torque 132,8 daNm [11755 lb-in] °

R2±0,2 [.0787±.0078]

ø38,1 -0,025 [1.5 -.001 ]

ø50 [1.968]

+0,018

ø40 -0,002

[1.575 +.0007 -.0001 ]

56 [2.205]

M12 min 25 [.984] Deep

M12 min 25 [.984] Deep

CO-ø1½" straight, Parallel key 3 8"x 3 8"x 2¼" BS46

K - tapered 1:10, Parallel key B12x8x28 DIN 6885

Max. Torque 132,8 daNm [11755 lb-in]

Max. Torque 210,7 daNm [18650 lb-in] 82 -0,2 [3.228 -.0079 ] 4 B [.157]

° R2±0,2 [.0787±.0078]

12 +0,01 -0,05 [.472 +.0004 -.0019 ]

[1.5 -.0019]

ø38,1 -0,05

ø50 [1.968]

42,4 -0,2 [1.669-.0079 ]

ø50 [1.968]

82 -0,2 [3.228 -.0079 ]

9.545 -0,02 [.379-.0008]

B-B

6 [.236]

ø6 [.236]

54±0,4 [2.126±.0157]

S=46 Tightening Torque 50±3 daNm [4425±265 lb-in]

B

Taper 1:10

ø56 [2.205]

R2±0,2 [.0787±.0078]

M30x2

45

Pitch 12/24 Teeth 17 0 Pressure angle 30

82 -0,2 [3.228 -.0079 ]

5:1

ø50 [1.968]

[1.693-.0079]

°

R2±0,2 [.0787±.0078]

82 -0,2 [3.228 -.0079 ]

12 -0,043 [.472-.0017]

43 -0,2

45

R2±0,2 [.0787±.0078]

R2±0,2 [.0787±.0078]

16,15 -0,2 [.634-.0079]

45

Max. Torque 132,8 daNm [11755 lb-in]

mm [in]

3/8-16 UNC min 25 [.984] deep

PERMISSIBLE SHAFT LOADS The curves apply to a B10 bearing life (ISO281) of 2000 hours at 200 RPM. Pr lbs

MTM

Pr daN 5600

Pr lbs 12000

12000 5000

5000 10000

10000 4000

4000 8000

8000 3000

3000 6000

6000 4000

2000

4000

2000 1000 0

MTMC

Pr daN 5600

2000

2000 1000

0 -80 -3

-60 -2

-40

-20 -1

0 0

20

40

60

1

80 3

2 Pr lbs

100

120

4

140

5

0 -80

0

mm

160

-60

-3

7 in

6

-40

-2

-20 -1

0

20

40

0

1

160

mm

MTMW

Pr daN 5600

12000 5000 10000 4000 8000 3000 6000 4000

2000

2000 1000 0

0 -80 -3

-60 -2

-40

-20 -1

0 0

20 1

40

60 2

16

80 3

100 4

120 5

140 6

7 in

60 2

80 3

100 4

120 5

140

160 mm 6

in

MTM MOTORS

DIMENSIONS AND MOUNTING DATA - MTMV

45,6 -1 [1.795 -.0394]

14 max [.551]

T

21±0,2 [.827±.0078]

ø110±0,1 [4.33±.0039] 9xM12

139 [5.472]

84±0,3

[3.307±.0118]

ø139 [5.472]

ø139 -0,2 [5.472 -.0079]

Port B

Port A

P(A,B) L1

L3

72 [2.834]

L2 max L

mm [in] Warning: Drain line should always be used. P(A, B): 2xG3/4 - 17 mm [.669 in] depth T : G1/4 12 mm [.472 in] depth (plugged) Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

L, mm [in] Type MTMV 200 151 [5.945] MTMV 250 157 [6.181] MTMV 315 167 [6.575] MTMV 400 177 [6.968] MTMV 470 185 [7.283] MTMV 500 191 [7.520] MTMV 630 187 [7.362] MTMV 725 196 [7.717]

L1, mm [in] 25 [.98] 31,3 [1.23] 40,5 [1.59] 51 [2.01] 59 [2.32] 65 [2.56] 61 [2.40] 70 [2.76]

L2, mm [in] L3, mm [in] 106,5 [4.193] 27,8 [1.094] 112,8 [4.441] 26,5 [1.043] 122,0 [4.803] 22,3 [.878] 132,5 [5.217] 21,8 [.858] 140,5 [5.531] 23,8 [.937] 146,5 [5.768] 27,8 [1.094] 142,5 [5.610] 26,8 [1.055] 151,5 [5.965] 27,8 [1.094]

DIMENSIONS OF THE ATTACHED COMPONENT 47 +0,5 [1.85+.0197 ]

T

ø90 [3.543]

min ø55 [2.165]

K

16DP 12/24

17 +0,4 [.669 +.0157 ]

ANS B92.1-76

F

J

I

F: Oil circulation hole J: 9xM12-30 mm [1.181 in] depth, 400, ø110±0,1 [4.33±.0039]

17

I: O- Ring 93x1,5mm [3.661x.059 in] T: Drain connection G1/4

MTM MOTORS

DIMENSIONS AND MOUNTING DATA - MTM6V

45,6 -1 [1.795 -.0394]

10° 14 max [.551]

T

21±0,2 [.827±.0078]

ø110±0,1 [4.33±.0039]

40°

139 [5.472]

20°

84±0,3 [3.307±.0118]

ø139 [5.472]

ø139 -0,2 [5.472 -.0079]

Port B

6xM12

20°

Port A

P(A,B)

L1

L3

40° 10°

L2 max L

Fig.1

mm [in] Warning: Drain line should always be used. P(A, B): 2xG3/4 - 17 mm [.669 in] depth T : G1/4 12 mm [.472 in] depth (plugged) Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

Type MTM6V 200 MTM6V 250 MTM6V 315 MTM6V 400 MTM6V 470 MTM6V 500 MTM6V 630 MTM6V 725

L, mm [in] 151 [5.945] 157 [6.181] 167 [6.575] 177 [6.968] 185 [7.283] 191 [7.520] 187 [7.362] 196 [7.717]

L1, mm [in] 25 [.98] 31,3 [1.23] 40,5 [1.59] 51 [2.01] 59 [2.32] 65 [2.56] 61 [2.40] 70 [2.76]

72 [2.834]

L2, mm [in] L3, mm [in] 106,5 [4.193] 27,8 [1.094] 112,8 [4.441] 26,5 [1.043] 122,0 [4.803] 22,3 [.878] 132,5 [5.217] 21,8 [.858] 140,5 [5.531] 23,8 [.937] 146,5 [5.768] 27,8 [1.094] 142,5 [5.610] 26,8 [1.055] 151,5 [5.965] 27,8 [1.094]

DIMENSIONS OF THE ATTACHED COMPONENT FOR MTM6V 47 +0,5 [1.85+.0197 ]

J

ø90 [3.543]

K

T

min ø55 [2.165]

17 +0,4 [.669 +.0157 ]

16DP 12/24 ANS B92.1-76

F

I F: Oil circulation hole 0 J: 9xM12-30 mm [1.181 in] depth, 40 , ø110±0,1 [4.33±.0039] or 6xM12-30 mm [1.181 in] depth, situated in accordance with the bolts M12, shown on Fig.1, ø110±0,1 [4.33±.0039]

I: O- Ring 93x1,5mm [3.661x.059 in] T: Drain connection G1/4

DRAIN CONNECTION A drain line ought to be used when pressure in the return line can exceed the permissible pressure. It can be connected at the drain connection of the attached component. The maximum pressure in the drain line is limited by the attached component and its shaft seal. The drain line must be possible for oil to flow freely between motor and attached component and must be led to the tank. The maximum pressure in the drain line is limited by the attached component and its seal. 18

MTM MOTORS

INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT

Standard ANS B92.1-1976, class 5 [m=2.1166; corrected x.m=+1,0]

Fillet Root Side Fit Number of Teeth Diametral Pitch Pressure Angle Pitch Dia. Major Dia. Minor Dia. Circular Space Width Fillet Radius Dimension Between Two Pins Pin Dia.

mm 16 12/24 0 30 33,8656 +0,4 38,4 +0,04 32,15 4,516±0,037 0,5 +0,10 26,9

D Dri Di Lo R L

inch 16 12/24 0 30 1.3333 1.5118÷1.5275 1.2657÷1.2673 .1763÷.1791 .02 1.063÷1.059

d

.19026÷.19034 4,835±0,001

z DP

L

Hardening Specification: HV=750±50 on the surface. HV=560 at 0,7±0,2 [.035÷.019] case depth Material: 20 MoCr4 EN 10084 or SAE8620.

ORDER CODE

1

2

3

4

5

6

7

MTM Pos.1 - Mounting Flange omit - 4-Bolt flange, spigot dia. ø160, BC ø200 C

- 4-Bolt flange, spigot dia. ø125, BC ø160

Pos.3 - Shaft Extensions* - ø40 straight, Parallel key A12x8x70 DIN6885 C 3 3 CO - ø1½ ” straight, Parallel key /8”x /8”x2¼” BS46

W

- Wheel motor

K

- ø45 tapered 1:10, Parallel key B12x8x28 DIN6885

V

- Very short mount, 9xM12 mounting bolts

6V

- Very short mount, 6xM12 mounting bolts

SH

- ø1½" splined 17T ANSI B92.1-1976

Pos.2 - Displacement code 200 250 315 400 470 500 630 725

- 201,4 cm3/rev [12.29 in3/rev] - 251,8 cm3/rev [15.36 in3/rev] - 326,3 cm3/rev [19.90 in3/rev] - 410,9 cm3/rev [25.06 in3/rev] - 475,0 cm3/rev [28.97 in3/rev] - 523,6 cm3/rev [31.95 in3/rev] - 631,2 cm3/rev [38.52 in3/rev] - 724,3 cm3/rev [44.20 in3/rev]

Pos.4 - Check Valves omit - without check valves 1 - with check valves

Pos.5 - Ports omit - BSPP (ISO 228)

Pos.6 - Special Features (see page 34) Pos.7 - Design Series omit - Factory specified

NOTES: * The permissible output torque for shafts must be not exceeded! ** Color at customer's request. The hydraulic motors are mangano-phosphatized as standard. 19

HYDRAULIC MOTORS TMF APPLICATION » » » » » » »

A

Marine equipment Forestry equipment Metal working machines Agriculture machines Road building machines Mining machinery Special vehicles etc.

B

CONTENTS

OPTIONS

Specification data ............................................ 21 Dimensions and mounting TMF....................... 22 Dimensions and mounting TMFA .................... 23 Permissible shaft loads ................................... 24 Order code ...................................................... 24

» Model- Disc valve, roll-gerotor » Wheel mounting flange » Side ports » Shaft- thread hole flange » SAE and BSPP ports » Other special features

GENERAL Max. Displacement,

3

3

cm /rev [in /rev]

Max. Speed,

724,3 [44.2] 750

[RPM]

Max. Torque,

daNm [in-lb]

Max. Output,

kW [HP]

Max. Pressure Drop,

bar [PSI]

Max. Oil Flow,

cont.: 175 [15490]

70 [94] cont.: 250 [3600] 5

[RPM]

Permissible Shaft Loads

Pa=1000 [2250]

daN [lbs]

Pressure fluid

int.: 350 [5080]

150 [40]

lpm [GPM]

Min. Speed,

int.: 215 [16030]

Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) O

Temperature range,

O

C [ F]

-40÷140 [-40÷284]

2

20÷75 [98÷347]

Optimal Viscosity range, mm /s [SUS]

ISO code 20/16 (Min. recommended fluid filtration of 25 micron)

Filtration

Pressure Losses Oil flow in drain line

flow in Pressure drop Viscosity Oil drain line bar [PSI] mm 2/s [ SUS] lpm [GPM ] 200 [2 90 0] 2 75 [3990]

20 [98]

2,5 [.660 ]

35 [164]

1,5 [ .400]

20 [98]

4 [1.057]

35 [164]

2,5 [.660]

350

25

300

20

250 200 150 100 50 0

15 10 5 0

0 0

20

25 5

75

50 10

15

20

100 25

125 Q, lpm 30

Q, GPM

MLHV TMF MOTORS

SPECIFICATION DATA

Type Displacement, 3

3

cm. /rev. [in. /rev.]

TMF 200

TMF 250

TMF 315

TMF 400

TMF 470

TMF 500

TMF 630

TMF 725

201,4

251,8

326,3

410,9

475

523,6

631,2

724

[12.29]

[15.36]

[19.9]

[25.06]

[28.97]

[31.95]

[38.52]

[44.2]

500

380

305

260

240

185

170

600

460

365

315

285

225

2 15

Max. Speed,

Cont.

625

[RPM]

Int.*

750

Max. Torque

Cont.

72 [6375] 90[7965] 116[10265] 147[13010] 171[15135] 172[15225] 175[15490] 160[14160]

daNm [in-lb]

Int.*

102 [9030] 128[11330] 163[14425] 206[18232] 215[16030] 215[19030] 215[19030] 192[17000]

Peak**

115[10180] 144[12745] 186[16460] 235[20800] 240[21240] 240[21240] 250[21225] 240[21240]

Max. Output

Cont.

41 [55]

41 [55]

41 [55]

41 [55]

41 [55]

37,5 [50]

28 [37,5]

26 [35]

kW [HP]

Int.*

65 [87]

70 [94]

70 [94]

70 [94]

55 [74]

51 [68]

42 [56]

40 [54]

Max. Pressure Drop

Cont.

250[3600] 250[3600] 250[3600] 250[3600] 250[3600] 230[3340] 185[2680] 160[2320]

bar [PSI]

Int.*

350[5080] 350[5080] 350[5080] 350[5080] 350[5080] 280[4060] 225[3260] 210[3045]

Peak**

400[5800] 400[5800] 400[5800] 400[5800] 400[5800] 320[4640] 270[3915] 260[3770]

Max. Oil Flow

Cont.

125[33]

125[33]

125[33]

125[33]

125[33]

125[33]

125[33]

125[33]

lpm [GPM]

Int.*

150[40]

150[40]

150[40]

150[40]

150[40]

150[40]

150[40]

150[40]

Max. Inlet Pressure

Cont.

270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920]

bar [PSI]

Int.*

370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370]

Peak**

420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100]

Max. Return Pressure

Cont.

without Drain Line or

Cont. 100-300 RPM 40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

40 [580]

Cont.

20 [290]

20 [290]

20 [290]

20 [290]

-

-

-

Max. Pressure in Drain Line, bar [PSI]

Int.*

0-100 RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100] >300 RPM 20 [290]

0-max. RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100]

75 [1100] 75 [1100] 75 [1100] 75 [1100]

75 [1100] 75 [1100] 75 [1100] 75 [1100]

Max. Return Pressure

Cont.

270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920]

with Drain Line

Int.*

370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370]

bar [PSI]

Peak**

420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100]

Max. Starting Pressure with Unloaded Shaft, bar [PSI] Min. Starting Torque daNm [in-lb] Min. Speed***, [RPM] Weight, kg [lb]

6 [90]

6 [90]

60[5310]

75[6640]

5

5

6 [90]

6 [90]

6 [90]

6 [90]

6 [90]

6 [90]

97[8585] 122[10800] 142[12570] 143[12655] 145[12830] 148[13100] 5

26,9[59.3] 27,3[60.2] 28,1[62]

5

5 29 [64]

5

5

5

29,7[65.5] 30,2[66.6] 29,7[65.5]

31[68.4]

* Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds of 5 RPM lower than given, consult factory or your regional manager.

1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better. 3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4). If using synthetic fluids consult the factory for alternative seal materials. 4. Recommended minimum oil viscosity 70 SUS [13 cm2/s] at 50°C [122°F]. 5. Recommended maximum system operating temperature is 82°C [180°F]. 6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

21

MLHV TMF MOTORS

DIMENSIONS AND MOUNTING DATA - TMF

60

60

5x 1 5

72 [2.835]

5 ø189 [7.441]

ø180 [7.087]

ø172 [6.772]

10xø14,2 +0,15 5xM14x1,5

[.559+.0059 ] (ø238) [9.37] 18 [.708]

6 [.236]

P(A,B)

21±0,15 [.827±.0059]

ø139 [5.472]

42±0,15 42±0,15 [1.654±.0059] [1.654±.0059]

Port B

ø92,8 [3.654]

ø180 [7.087]

5x 1

0 ø14 2] 1 [5.5

ø2 [8.2 10 68]

Port A

T

L1

7

12

[.276]

[.472] 113 max [4.449]

5 [.197]

P(A, B): 2xG3/4 - 17 mm [.669 in] depth T : G1/4 - 12 mm [.472 in] depth

L2 L3

mm [in]

max L

Warning: Drain line should always be used.

Type Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

TMF 200 TMF 250 TMF 315 TMF 400 TMF 470 TMF 500 TMF 630 TMF 725

22

L, mm [ in] L1, mm [in] L2,mm [in] L3, mm [in] 126 [4.96] .98 [25] 83 [3.268] 110,3 [4.34] 132.3 [5.21] 31,3 [1.23] 89.3 [3.516] 116,6 [4.59] 141.5[5.57] 40,5 [1.59] 98.5 [3.878] 125,8 [4.95] 152 [5.98] 51 [2.01] 109 [4.291] 136,3 [5.37] 160 [6.30] 59 [2.32] 117 [4.606] 144,3 [5.68] 166 [6.54] 65 [2.56] 123 [4.843] 150,3 [5.92] 162 [6.38] 61 [2.40] 119 [4.69] 146,3 [5.76] 171 [6.73] 70 [2.76] 128 [5.04] 155,3 [6.11]

MLHV TMF MOTORS

DIMENSIONS AND MOUNTING DATA - TMFA

60

5x 1 5

ø189 10xø14,2 +0,15 [.559+.0059 ]

ø152,4

ø210

[6.0]

[8.268]

ø238 18 [.708]

6 [.236]

[9.37]

P(A,B)

21±0,15 [.827±.0059]

Port A L1 7

12

[.276]

[.472] 5 113 max

[.197]

[4.449]

T

[5.472]

ø139

ø109,22 [4.3]

42±0,15 42±0,15 [1.654±.0059][1.654±.0059]

Port B

P(A, B): 2x1 1/16-12 UN, O-ring port 17 mm [.669 in] depth T : 9/16-18 UNF, O-ring port 12 mm [.472 in] depth

L2 L3 max L

mm [in] Warning: Drain line should always be used.

Type

TMFA 200 Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

TMFA 250 TMFA 315 TMFA 400 TMFA 470 TMFA 500 TMFA 630 TMFA 725

23

L, mm [ in] L1, mm [in] L2,mm [in] L3, mm [in] 126 [4.96] .98 [25] 83 [3.268] 110,3 [4.34] 132.3 [5.21] 31,3 [1.23] 89.3 [3.516] 116,6 [4.59] 141.5[5.57] 40,5 [1.59] 98.5 [3.878] 125,8 [4.95] 152 [5.98] 51 [2.01] 109 [4.291] 136,3 [5.37] 160 [6.30] 59 [2.32] 117 [4.606] 144,3 [5.68] 166 [6.54] 65 [2.56] 123 [4.843] 150,3 [5.92] 162 [6.38] 61 [2.40] 119 [4.69] 146,3 [5.76] 171 [6.73] 70 [2.76] 128 [5.04] 155,3 [6.11]

[7.441]

ø180

[7.087]

72

[2.835]

5

ø172 [6.772]

5x 1

ø180 [7.087]

60 6x5/8-18 UNF

MLHV TMF MOTORS

PERMISSIBLE SHAFT LOADS The load diagram is valid for an average bearings life of 2000 hours at 100 RPM Prad daN 12000

1

0.5

2

1.5

2.5

3

3.5

4

4.5 L, in

24000

B

10000

Prad lbs 26000 22000 20000

8000

18000

A

16000 14000

6000

12000 10000

4000

8000 6000

2000

4000 2000

0

10

20

30

40

50

60

70

80

90

100

110

120 L, mm

A - Permissible radial shaft load. B - Max. radial shaft load. Any shaft load exceeding the values shown in the curve will involve a risk of breakage

ORDER CODE 1

2

3

4

TMF Pos.1 - Mounting Flange omit - Thread hole flange, 5xM12x1,5 on ø140 A

- Thread hole flange, 6x5/8-18 UNF on ø152,4

Pos.2 - Displacement code 200 250 315 400 470 500 630 725

3

3

- 201,4 [12.29] cm. /rev. [in. /rev.] 3 3 - 251,8 [15.36] cm. /rev. [in. /rev.] 3 3 - 326,3 [19.90] cm. /rev. [in. /rev.] 3 3 - 410,9 [25.06] cm. /rev. [in. /rev.] 3 - 475,0 [28.97] cm. /rev. [in.3/rev.] - 523,6 [31.95] cm.3/rev. [in.3/rev.] - 631,2 [38.52] cm.3/rev. [in.3/rev.] - 724,3 [44.20] cm.3/rev. [in.3/rev.]

Pos.3 - Special Features (see page 34) Pos.4 - Design Series omit - Factory specified The hydraulic motors are mangano-phosphatized as standard.

24

HYDRAULIC MOTORS MVM APPLICATION » » » » » » » »

Conveyors Metal working machines Agriculture machines Road building machines Mining machinery Food industries Special vehicles Plastic and rubber machinery etc.

A

B

OPTIONS » Model- Disc valve, roll-gerotor » Flange with wheel mount » Short motor » Side ports » Shafts- straight, splined and tapered » BSPP ports; » Other special features.

CONTENTS Specification data .......................... 26 Dimensions and mounting ...............27 Shaft extensions ............................ 27 Permissible shaft Seal Pressure .... 28 Permissible shaft loads .................. 29 Order code ..................................... 29

EXCELLENCE » High torque and pressure drop » High inlet pressure » High starting torque » Improved efficiency at high pressure drop » Smooth operation at low speed » High radial and axial bearing capacity

GENERAL Max. Displacement,

3

3

801,8 [48.91]

cm /rev [in /rev]

Max. Speed,

736

[RPM]

Max. Torque,

daNm [lb-in]

Max. Output,

kW [HP]

Max. Pressure Drop,

bar [PSI]

Max. Oil Flow,

cont.: 259 [22920]

112 [150] cont.: 250 [3630] 5

[RPM]

Permissible Shaft Loads,

int.: 350 [5080]

240 [63.4]

lpm [GPM]

Min. Speed,

int.: 340 [30090]

Pa=1500 [3370]

daN [lbs]

Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)

Pressure fluid O

Temperature range,

-40÷140 [-40÷284]

O

C [ F]

20÷75 [98÷347]

2

Optimal Viscosity range, mm /s [SUS]

ISO code 20/16 (Min. recommended fluid filtration of 25 micron)

Filtration

Pressure Losses

Oil flow in drain line 30 400

flow in Pressure drop Viscosity Oil drain line 2 bar [PSI] mm /s [ SUS] lpm [GPM ] 200 [2 90 0] 2 75 [3990]

20 [98]

2,5 [.660 ]

35 [164]

1,5 [ .400]

20 [98]

4 [1.057]

35 [164]

2,5 [.660]

25 300 200

20 15 10

100 0

5 0

0 0

25

25 5

50 10

15

75 20

100 25

125 30

35

150 40

200 Q, lpm

175 45

50

Q, GPM

MVM MOTORS

SPECIFICATION DATA

Type Displacement, cm3/rev. [in3/rev.]

MVM 315

MVM 400

314,5 [19.18] 400,9 [24.5]

MVM 500

MVM 630

MVM 800

499,6 [30.5]

629,1 [38.38]

801,8 [48.91]

Max. Speed,

cont.

636

500

400

315

250

[RPM]

Int.*

736

600

480

380

300

Max. Torque

cont.

115 [10180]

144 [12745]

180 [15930]

227 [20090]

259 [22920]

daNm [lb-in]

Int.*

160 [14160]

200 [17700]

260 [23010]

310 [27440]

340 [30090]

peak**

180 [15930]

230 [20355]

286 [25315]

360 [31860]

402 [35580]

Max. Output

cont.

67 [90]

67 [90]

67 [90]

67 [90]

67 [90]

kW [HP]

int.*

112 [150]

112 [150]

112 [150]

112 [150]

112 [150]

Max. Pressure Drop

cont.

250 [3630]

250 [3630]

250 [3630]

250 [3630]

225 [3263]

bar [PSI]

Int.*

350 [5080]

350 [5080]

350 [5080]

350 [5080]

300 [4350]

peak**

400 [5800]

400 [5800]

400 [5800]

400 [5800]

350 [5080]

Max. Oil Flow

cont.

200 [52.8]

200 [52.8]

200 [52.8]

200 [52.8]

200 [52.8]

lpm [GPM]

Int.*

240 [63.4]

240 [63.4]

240 [63.4]

240 [63.4]

240 [63.4]

Max. Inlet Pressure

cont.

270 [3915]

270 [3915]

270 [3915]

270 [3915]

270 [3915]

bar [PSI]

Int.*

370 [5365]

370 [5365]

370 [5365]

370 [5365]

370 [5365]

peak**

420 [6090]

420 [6090]

420 [6090]

420 [6090]

420 [6090]

140 [2030]

140 [2030]

140 [2030]

140 [2030]

140 [2030]

Max. Return Pressure cont. with Drain Line

Int.*

175 [2540]

175 [2540]

175 [2540]

175 [2540]

175 [2540]

bar [PSI]

peak**

210 [3045]

210 [3045]

210 [3045]

210 [3045]

210 [3045]

5 [70]

5 [70]

5 [70]

5 [70]

5 [70]

92 [8140]

115 [10180]

144 [12745]

180 [15930]

205 [18145]

10

6

8

6

5

41,3 [91]

42,1 [93]

43 [95]

44,5 [98]

46 [101.4]

Max. Starting Pressure with Unloaded Shaft, bar [PSI] Min. Starting Torque daNm [lb-in] Min. Speed***, [RPM] Weight, kg [lb]

* Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron or better. 3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4). If using synthetic fluids consult the factory for alternative seal materials. 4. Recommended minimum oil viscosity 13 mm²/s [70 SUS] at 50°C [122°F]. 5. Recommended maximum system operating temperature is 82°C [180°F]. 6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

26

MVM MOTORS

DIMENSIONS AND MOUNTING DATA CO Shaft

K Shaft

SH Shaft

C Shaft

ø160 -0,063

L2

20±0,3 [.787±.012]

[.433 +.0079]

Shaft Dim. See Page 28

11+0,2

145 [5.71]

105 [4.134]

79 [3.11]

122 [4.8]

[6.3 -.0025 ]

L1

15±0,15 [.59±.0059]

21±0,15 [.827±.0059]

max L

ø160 [6.299]

P(A,B)

50±0,15 50±0,15 [1.97±.0059] [1.97±.0059]

85 -0,5 [3.35 -.0196 ]

160 [6.299]

Port A

ø200±0,4 [7.87±.016] 4xø18 [.708]

Port B

2

P (A,B) T

179 [7.05]

T

Versions

2xG1 G¼

4

2x15/ 16 -12UN 9 / 16 -18UNF

Warning: Drain line should always be used. 179 [7.05]

Type

L,mm [in]

L2,mm [in]

L1,mm [in]

MVM 315 226,5 [8.92]

172,5 [6.79] 25,5 [1.00]

MVM 400 233,5 [9.19]

179,5 [7.07] 32,5 [1.28]

MVM 500 241,5 [9.51]

187,5 [7.38] 40,5 [1.59]

MVM 630

252 [9.92]

198 [7.79]

51 [2.01]

MVM 800 266 [10.47]

212 [8.35]

65 [2.56]

Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

mm [in] 27

MVM MOTORS

SHAFT EXTENSIONS C - ø50 straight, Parallel key A14x9x70 DIN 6885

12,72-0,02 [.502-.0008]

+.0008

M12 min 26 [1.024] deep

ø57,15 - 0,015 [2.25 - .0006]

79 [3.11]

ø62,9- 0,2 [2.48 - .0079]

[1.968 +.0007 ]

+0,018 ø50 +0,002

3/8-16 UNC min 25 [.98] deep

K - tapered 1:10, Parallel key B16x10x32 DIN 6885 70 [2.756]

79 [3.11]

16 -0,043 [.63 -.0017 ]

M12 min 26 [1.024] deep

7 [.275]

S=65 Tightening Torque 70±1 daNm [6196±88.5 lb-in]

ø8 [.315]

40 [1.575]

ø60 [2.362]

32,25 - 0,2 [2.27- .0079 ]

ø53,975 - 0,025 [2.125 - .001]

56 +2 [2.205+.079 ]

ø60 [2.362]

A

A-A

A

Taper 1:10

105 [4.134]

ø78 [3.01]

SH - ø2 1/8 "splined, 16 DP 8/16 ANS B92.1-1976

M42x3

+0,5 ø53 +0,2

+.0197 [2.086+.0079 ]

ø60 [2.362]

79 [3.11]

ø60 [2.362]

14 -0,043 [.551-0017]

CO - ø2¼"[57,15] straight,Parallel key ½ "x½"x 2¼" BS46

6 [.236]

mm [in]

MAX. PERMISSIBLE SHAFT SEAL PRESSURE Max. return pressure without drain line or max. pressure in the drain line DP [PSI] 1000

DP [bar] 80 70 60

750 500 250

50

- continuous operations - intermittent operations

40 30 20 10

0

0

n 0

50 100 150 200 250 300 350 400 450 500 550 600 [RPM] 28

MVM MOTORS

PERMISSIBLE SHAFT LOADS The output shaft runs in tapered bearings that permit high axial and radial forces. Curve "1" shows max. radial shaft load. Any shaft load exceeding the values quoted in the curve will seriously reduce motor life. The two other curves apply to a B10 bearing life of 3000 hours at 200 RPM. Prad daN

4

3

2

0

1

-1 in

Prad lbs 14000

6000 1500 daN 3370 lbs.

5000

1

2

12000

1500 daN 3370 lbs.

10000

4000

2 - Pa=0 daN [0 lbs] 3 - Pa=1500 daN [3370 lbs]

8000 3000

3 6000

2000

4000

1000

2000

-125 -100 -75

-50

-25

25

0

50 mm

ORDER CODE 1

2

3

4

5

6

MVM Pos.1 - Displacement code 315 400 500 630 800

3

Pos.3 - Ports 3

- 314,5 cm /rev [19.8 in /rev] - 400,9 cm3/rev [24.45 in3/rev] - 499,6 cm3/rev [30.48 in3/rev] - 629,1 cm3/rev [38.38 in3/rev] - 801,8 cm3/rev [48.91 in3/rev]

2 4

- side ports, 2xG1, G1/4, BSP thread, ISO 228 - side ports, 2x1 5/16-12 UN, O-ring, 9/16-18 UNF

Pos.4 - Check Valves omit - without check valves 1 - with check valves

Pos.2 - Shaft Extensions*

Pos.5 - Special Features (see page 34)

- ø50 straight, Parallel key A14x9x70 DIN6885 C 1 1 1 1 CO - ø2 /4" straight, Parallel key /2"x /2"x2 /4" DIN6885 1

SH

- ø2 /8" splined, ANS B92.1-1976

K

- ø60 tapered 1:10, Parallel key B16x10x32 DIN6885

Pos.6 - Design Series omit - Factory specified

NOTES: * The permissible output torque for shafts must be not exceeded! The hydraulic motors are mangano-phosphatized as standard. 29

HYDRAULIC MOTORS VMF APPLICATION » » » » » » »

A

Marine equipment Forestry equipment Metal working machines Agriculture machines Road building machines Mining machinery Special vehicles etc.

B

CONTENTS

OPTIONS

Specification data ............................................ 31 Dimensions and mounting ............................... 32 Permissible shaft seal pressure........................32 Permissible shaft loads ................................... 33 Order code ...................................................... 33

» Model- Disc valve, roll-gerotor » Wheel mounting flange » Side ports » Shaft- thread hole flange » SAE and BSPP ports » Other special features

GENERAL Max. Displacement,

3

3

801,8 [48.91]

cm /rev [in /rev]

Max. Speed,

736

[RPM]

Max. Torque,

daNm [lb-in]

Max. Output,

kW [HP]

Max. Pressure Drop,

bar [PSI]

Max. Oil Flow,

cont.: 259 [22920]

112 [150] cont.: 250 [3630] 5

[RPM]

Permissible Shaft Loads,

Pa=1500 [3370]

daN [lbs]

Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)

Pressure fluid O

Temperature range,

-40÷140 [-40÷284]

O

C [ F]

20÷75 [98÷347]

2

Optimal Viscosity range, mm /s [SUS]

ISO code 20/16 (Min. recommended fluid filtration of 25 micron)

Filtration

Pressure Losses

Oil flow in drain line 400

flow in Pressure drop Viscosity Oil drain line 2 bar [PSI] mm /s [ SUS] lpm [GPM ] 200 [2 90 0] 2 75 [3990]

int.: 350 [5080]

240 [63.4]

lpm [GPM]

Min. Speed,

int.: 340 [30090]

20 [98]

2,5 [.660 ]

35 [164]

1,5 [ .400]

20 [98]

4 [1.057]

35 [164]

2,5 [.660]

300 200

30 25 20 15 10

100 0

5 0

0

25 5

0

30

50 10

15

75 20

100 25

125 30

35

150 40

200 Q, lpm

175 45

50

Q, GPM

MLHV VMF MOTORS

SPECIFICATION DATA Type Displacement, cm3/rev. [in3/rev.]

VMF 315

VMF 400

314,5 [19.18] 400,9 [24.5]

VMF 500

VMF 630

VMF 800

499,6 [30.5]

629,1 [38.38]

801,8 [48.91]

Max. Speed,

cont.

636

500

400

315

250

[RPM]

Int.*

736

600

480

380

300

Max. Torque

cont.

115 [10180]

144 [12745]

180 [15930]

227 [20090]

259 [22920]

daNm [lb-in]

Int.*

160 [14160]

200 [17700]

260 [23010]

310 [27440]

340 [30090]

peak**

180 [15930]

230 [20355]

286 [25315]

360 [31860]

402 [35580]

Max. Output

cont.

67 [90]

67 [90]

67 [90]

67 [90]

67 [90]

kW [HP]

int.*

112 [150]

112 [150]

112 [150]

112 [150]

112 [150]

Max. Pressure Drop

cont.

250 [3630]

250 [3630]

250 [3630]

250 [3630]

225 [3263]

bar [PSI]

Int.*

350 [5080]

350 [5080]

350 [5080]

350 [5080]

300 [4350]

peak**

400 [5800]

400 [5800]

400 [5800]

400 [5800]

350 [5080]

Max. Oil Flow

cont.

200 [52.8]

200 [52.8]

200 [52.8]

200 [52.8]

200 [52.8]

lpm [GPM]

Int.*

240 [63.4]

240 [63.4]

240 [63.4]

240 [63.4]

240 [63.4]

Max. Inlet Pressure

cont.

270 [3915]

270 [3915]

270 [3915]

270 [3915]

270 [3915]

bar [PSI]

Int.*

370 [5365]

370 [5365]

370 [5365]

370 [5365]

370 [5365]

peak**

420 [6090]

420 [6090]

420 [6090]

420 [6090]

420 [6090]

140 [2030]

140 [2030]

140 [2030]

140 [2030]

140 [2030]

Max. Return Pressure cont. with Drain Line

Int.*

175 [2540]

175 [2540]

175 [2540]

175 [2540]

175 [2540]

bar [PSI]

peak**

210 [3045]

210 [3045]

210 [3045]

210 [3045]

210 [3045]

5 [70]

5 [70]

5 [70]

5 [70]

5 [70]

92 [8140]

115 [10180]

144 [12745]

180 [15930]

205 [18145]

10

6

8

6

5

46 [101.4]

47,2 [104,1]

48,5 [106.9]

50 [110.2]]

51,5 [113.5]

Max. Starting Pressure with Unloaded Shaft, bar [PSI] Min. Starting Torque daNm [lb-in] Min. Speed***, [RPM] Weight, kg [lb]

* Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal fi ltration of 25 micron or better. 3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4). If using synthetic fluids consult the factory for alternative seal materials. 4. Recommended minimum oil viscosity 13 mm²/s [70 SUS] at 50°C [122°F]. 5. Recommended maximum system operating temperature is 82°C [180°F]. 6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

31

MLHV VMF MOTORS

DIMENSIONS AND MOUNTING DATA ø302±0,5 [11.89±.0197] 8xø17,6 +0,2

20

20

0

ø17 [6.6 0 93]

0

ø235 [9.252]

85 -0,5 -0,1

[8.819-.0039 -.0079]

ø224 -0,2

-0,1

ø224 -0,2

[8.819-.0039 -.0079]

ø200 -0,2 [7.874-.0079 ]

[3.346-.0197]

[.693+.0079 ]

65 ] ø2 433 0. 1 [ 20

0

6x

138,5±0,8 [5.453±.032]

60

0

6xM16

max L

L2

6±0,1 [.236±.0039]

16±0,25 [.63±.0098]

5±0,15

50±0,15 50±0,15

Port B

Type

2

4

2xG1 G¼

2x15/ 16 -12UN 9 / 16 -18UNF

L, mm [in] L1, mm [in] L2, mm [in]

VMF 315 286,5 [11.28] 25,5 [1.00] 109,5 [4.31] VMF 400 293,5 [11.56] 32,5 [1.28] 116,5 [4.59] VMF 500 301,5 [11.87] 40,5 [1.59] 124,5 [4.90]

Port A

VMF 630 312,0 [12.28] 51,0 [2.01] 135,0 [5.31] VMF 800 326,0 [12.83] 65,0 [2.56] 149,0 [5.87]

21±0,15 [.827±.0059]

[.905]

[.197±.0059]

P (A,B) T

T

L1

23

[1.968±.0059] [1.968±.0059]

ø160 -0,2 [6.299-.0079]

ø160 -0,2 [6.299-.0079]

0

[5.118-.0039 -.0118 ]

-0,1 ø130 -0,3

30

Versions

15±0,15 [.59±.0059]

P(A,B)

5±0,15 [.197±.0059]

Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW

Warning: Drain line should always be used.

Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

MAX. PERMISSIBLE SHAFT SEAL PRESSURE P PSI 1000 800 600 400

P bar 70 60 50 40 30 20

200 0

10 0

100

200

300

32

400

500

600

700 n, RPM

mm [in]

MLHV VMF MOTORS

PERMISSIBLE SHAFT LOADS Pr daN 15000

-1

-.5

0

.5

1

1.5

2

2.5

3

3.5

Pr lbs

4.5 in

4

32000

14000

30000

13000

28000

12000

26000

11000

24000

10000

22000

9000

2

8000

20000 18000

7000

16000

6000

14000

1

5000

10000

4000

0

12000 8000

-20 -10

0

10

20

30

40

50

60

70

80

90 100 110 120 mm

1 - Bearing curve: The curve applies to a B10 bearing life of 2000 hours at 100 RPM. 2 - Shaft curve: The curve represents Max. permissible radial shaft load with safety factor 2:1.

ORDER CODE 1

2

3

4

VMF Pos.1 - Displacement code 315 400 500 630 800

3

3

- 314,5 cm /rev [19.18 in /rev] - 400,9 cm3/rev [24.45 in3/rev] - 499,6 cm3/rev [30.48 in3/rev] - 629,1 cm3/rev [38.38 in3/rev] - 801,8 cm3/rev [48.91 in3/rev]

Pos.2 - Ports 2

- side ports, 2xG1, G¼, BSP thread, ISO 228

4

- side ports, 2x15 16 -12 UN, O-ring, 9 16 -18 UNF

Pos.3 - Special Features (see page 34) Pos.4 - Design Series omit - Factory specified The hydraulic motors are mangano-phosphatized as standard.

33

MOTOR SPECIAL FEATURES

Special Feature Description

Order Code

MSWM

MTM

TMF

MVM

VMF

Motor type

Speed Sensor*

RS

O

O

O

O

O

Reinforced motor

HD

-

O

O

O

O

Low Leakage

LL

O

O

O

O

O

LSV

O

O

O

O

O

Reverse Rotation

R

O

O

O

O

O

Paint**

P

O

O

O

O

O

PC

O

O

O

O

O

S

O

-

O

-

Low Speed Valving

Corrosion Protected Paint** Check Valves

O Optional - Not applicable S Standard * For sensor ordering see pages 35-36. ** Color at customer's request.

For more information about HD option please contact with "M+S Hydraulic".

34

MOTORS WITH SPEED SENSOR MSWM...RS 53 [2.086]

max 50 [1.97]

max 110 [4.33]

M12x1

MTM...RS TMF...RS

80

0

60 [2.36]

max 51,5 [2.03]

57 [2.24]

71 [2.8] 0

M12x1

80

MVM...RS VMF...RS

M12x1

140 [5.51]

35

max 70,5 [2.77]

SPEED SENSOR

MOTORS

TECHNICAL DATA OF THE SPEED SENSOR

Technical data Frequency range Output Power supply Current input Ambient Temperature Protection Plug connector Mounting principle

Output signal

0...15 000 Hz PNP, NPN 10...36 VDC 20 mA (@24 VDC) -40...+1250C [-40...+2570F] IP 67 M12-Series ISO 6149

Uhigh>Ud.c.-2V

U

Ulow