Rodamientos rígidos de una hilera de bolas Radial deep groove ball bearings, single row
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm)
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
D (mm)
B (mm)
Dinámico Dynamic C
3
10
4
0.53
0.180
61200
72000
0.0015
623
4
9 11 12 13 16
2.5 4 4 5 5
0.53 0.71 0.79 0.92 1.1
0.180 0.230 0.230 0.290 0.380
65025 61200 57375 51255 45900
76500 72000 67500 60300 54000
0.0007 0.0017 0.0021 0.0031 0.0054
618/4 619/4 604 624 634
5
11 13 16 19
3 4 5 6
0.63 0.87 1.12 2.30
0.250 0.34 0.38 0.94
57375 51255 45900 38250
67500 60300 54000 45000
0.0012 0.0025 0.0050 0.009
618/5 619/5 625 635
6
13 15 19
3.5 5 6
0.87 1.2 2.30
0.34 0.47 0.94
51255 48195 38250
60300 56700 45000
0.002 0.0039 0.0084
618/6 619/6 626
7
14 17 19 22
3.5 5 6 7
0.94 1.45 2.30 3.4
0.4 0.55 0.94 1.35
48195 42840 40545 34425
56700 50400 47700 40500
0.0022 0.0049 0.0075 0.013
618/7 619/7 607 627
8
16 19 22 24
4 6 7 8
1.3 1.9 3.4 3.9
0.56 0.73 1.35 1.63
42840 38250 36720 30600
50400 45000 43200 36000
0.0030 0.0071 0.012 0.017
618/8 619/8 608 628
9
17 20 24 26
4 6 7 8
1.40 2.1 3.9 4.65
0.63 0.85 1.63 1.93
40545 36720 32895 29070
47700 43200 38700 34200
0.0034 0.0076 0.014 0.02
618/9 619/9 609 629
10
15 19 19 22 26 28 30 35
3 5 7 6 8 8 9 11
66 1.40 133 2.0 4.7 4.5 5.3 8.4
34 0.58 056 0.84 1.93 1.93 2.32 3.34
36000 36720 34000 34425 30600 30600 26010 24480
43000 43200 40500 40500 36000 36000 30600 28800
0.005 0.0055 0.007 0.01 0.019 0.022 0.032 0.053
61700 61800 63800 61900 6000 16100 6200 6300
12
18 21 21 24 28 30 32 37
4 5 7 6 8 8 10 12
72 1.40 149 2.2 5.30 5 7.2 9.9
41 0.66 0.68 0.97 2.32 2.32 3.04 4.07
31000 32895 30500 30600 29070 26010 24480 21420
37000 38700 36000 36000 34200 30600 28800 25200
0.004 0.0063 0.005 0.011 0.022 0.023 0.037 0.06
61701 61801 63801 61901 6001 16101 6201 6301
15
21 24 24
4 5 7
81 1.53 162
44 0.79 0.79
27000 29070 26000
32000 34200 31500
0.006 0.0074 0.01
61702 61802 63802
d (mm)
46
Coeficiente de carga (KN) Load rating (KN)
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm)
Coeficiente de carga (KN) Load rating (KN)
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
Dinámico Dynamic C
Estático Static C0
7 8 9 11 13
4.28 5.7 5.7 7.9 11.7
2.2 2.8 2.8 3.68 5.3
26010 24480 24480 21420 18360
30600 28800 28800 25200 21600
0.016 0.025 0.03 0.045 0.082
61902 16002 6002 6202 6302
23 26 26 30 35 35 40 40 47 62
4 5 7 7 8 10 9 12 14 17
80 1.65 175 4.53 6.24 6.24 9.37 9.8 14 22.5
50 0.92 0.90 2.5 3.19 3.19 4.66 4.66 6.42 10.6
25000 26010 24000 24480 21420 21420 18360 18360 16830 13770
30000 30600 29500 28800 25200 25200 21600 21600 19800 16200
0.007 0.0082 0.013 0.018 0.032 0.039 0.048 0.065 0.12 0.27
61703 61803 63803 61903 16003 6003 98203 6203 6303 6403
20
27 32 37 42 42 42 47 52 72
4 7 9 8 9 12 14 15 19
84 3.95 6.25 7.14 7.8 9.8 13.3 16.5 30
57 2.3 3.6 4 4.5 4.9 6.5 7.7 14.7
21000 21420 19890 18360 18360 18360 15300 14535 11475
25000 25200 23400 21600 21600 21600 18000 17100 13500
0.013 0.018 0.038 0.05 0.051 0.069 0.11 0.14 0.4
61704 61804 61904 16004 98204 6004 6204 6304 6404
22
50 56
14 16
13.8 18.3
7.5 9.2
14535 13770
17100 16200
0.12 0.18
62/22 63/22
25
32 37 42 47 47 52 52 62 80
4 7 9 8 12 9 15 17 21
90 4.28 6.88 7.9 11.7 10.4 14.5 22.9 35
66 2.6 4.3 4.7 6.5 6.5 7.7 11.4 19
19000 18360 16830 15300 15300 13770 13770 12240 9945
23000 21600 19800 18000 18000 16200 16200 14400 11700
0.017 0.022 0.045 0.06 0.08 0.078 0.13 0.23 0.53
61705 61805 61905 16005 6005 98205 6205 6305 6405
28
58 68
16 18
16.5 24.6
9.4 13.5
12240 10710
14400 12600
0.18 0.29
62/28 63/28
30
37 42 47 55 55 62 72 90
4 7 9 9 13 16 19 23
95 4.4 7.14 11.7 13.5 19.9 29 42.8
76 2.9 4.5 7.3 8.2 11 15.7 23.2
17000 15300 14535 13005 13005 11475 9945 8415
20000 18000 17100 15300 15300 13500 11700 9900
0.022 0.027 0.051 0.085 0.12 0.20 0.35 0.74
61706 61806 61906 16006 6006 6206 6306 6406
d (mm)
D (mm)
15
28 32 32 35 42
17
B (mm)
47
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
48
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
35
44 47 55 62 62 72 80 100
5 7 10 9 14 17 21 25
155 4.7 9.37 12.8 16.5 26.5 34.4 54.2
130 3.2 6.7 8 10 15 18.7 30.4
14000 13770 12240 11475 11475 9945 9180 7650
17000 16200 14400 13500 13500 11700 10800 9000
0.025 0.03 0.08 0.11 0.16 0.29 0.46 0.95
61707 61807 61907 16007 6007 6207 6307 6407
40
50 52 62 68 68 80 90 110
6 7 12 9 15 18 23 27
207 4.9 13.5 13.5 17.5 31.9 41.5 62.5
177 3.4 9.8 9 11.4 18.7 23.6 35.8
13000 12240 10710 10710 10710 8415 8415 6885
16000 14400 12600 12600 12600 9900 9900 8100
0.03 0.034 0.12 0.13 0.19 0.37 0.63 1.25
61708 61808 61908 16008 6008 6208 6308 6408
45
55 58 68 75 75 85 100 120
6 7 12 10 16 19 25 29
213 6.5 13.8 16.2 21.7 34.4 54.2 74.6
192 6 10.6 10.6 14.4 21.2 30.9 44.1
12000 10710 9945 9180 9180 8415 7268 6503
14000 12600 11700 10800 10800 9900 8550 7650
0.035 0.04 0.14 0.17 0.25 0.41 0.83 1.55
61709 61809 61909 16009 6009 6209 6309 6409
50
65 72 80 80 90 110 130
7 12 10 16 20 27 31
6.7 14.4 16.5 22.5 36.4 63.7 85.4
6.7 11.6 11.2 15.7 22.8 37.3 51
9945 9180 8415 8415 7650 6503 5738
11700 10800 9900 9900 9000 7650 6750
0.052 0.14 0.18 0.26 0.46 1.05 1.9
61810 61910 16010 6010 6210 6310 6410
55
72 80 90 90 100 120 140
9 13 11 18 21 29 33
8.86 16.2 19.9 29 45.3 72.7 97.6
8.7 13.8 13.8 20.8 28.5 44.1 60.8
9180 8415 7650 7650 6885 6120 5355
10800 9900 9000 9000 8100 7200 6300
0.083 0.19 0.26 0.39 0.61 1.35 2.3
61811 61911 16011 6011 6211 6311 6411
60
78 85 95 95 110 130 150
10 13 11 18 22 31 35
11.7 16.2 20.4 30.1 54.2 83.5 105.9
11.2 14.1 14.7 22.8 35.3 51 68.2
8415 7650 7268 7268 6120 5355 4820
9900 9000 8550 8550 7200 6300 5670
0.11 0.2 0.28 0.42 0.78 1.7 2.75
61812 61912 16012 6012 6212 6312 6412
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
65
85 90 100 100 120 140 160
10 13 11 18 23 33 37
12.2 17.1 22.1 31.3 57.4 95.6 116.7
12.5 15.7 16.3 24.5 39.7 58.8 76.5
7650 7268 6885 6885 5738 5126 4590
9000 8550 8100 8100 6750 6030 5400
0.13 0.22 0.3 0.44 0.99 2.1 3.30
61813 61913 16013 6013 6213 6313 6413
70
90 100 110 110 125 150 180
10 16 13 20 24 35 42
12.2 23.4 28.6 38.9 62.5 108.8 140.2
13 20.8 24.5 30.4 44.1 66.7 102
6885 6503 6120 6120 5355 4820 4055
8100 7650 7200 7200 6300 5670 4770
0.14 0.35 0.43 0.6 1.05 2.5 4.85
61814 61914 16014 6014 6214 6314 6414
75
95 105 110 115 115 130 160 190
10 16 12 13 20 25 37 45
12.5 23.8 28.1 29.6 40.8 67.7 116.7 150
19 26.5 26.5 32.9 48.3 75 111.8
6503 6120 6120 5738 5738 5126 4284 3825
7650 7200 7200 6750 6750 6030 5040 4500
0.15 0.37 0.38 0.46 0.64 1.2 3 6.8
61815 61915 16115 16015 6015 6215 6315 6415
80
100 110 125 125 140 170 200
10 16 14 22 26 39 48
12.8 24.6 34.4 48.5 71.4 127.4 159.8
14.8 20 30.9 39.3 54 84.8 122.6
6120 5738 5355 5355 4590 4055 3672
7200 6750 6300 6300 5400 4770 4320
0.15 0.4 0.6 0.85 1.4 3.6 8
61816 61916 16016 6016 6216 6316 6416
85
110 120 130 130 150 180 210
13 18 14 22 28 41 52
19.2 31.3 35.1 51 85.4 137.3 170.6
20.4 29.5 32.9 42.2 62.8 94.6 134.3
5738 5355 5126 5126 4284 3825 3443
6750 6300 6030 6030 5040 4500 4050
0.27 0.55 0.63 0.89 1.8 4.25 9.5
61817 61917 16017 6017 6217 6317 6417
90
115 125 140 140 160 190 225
13 18 16 24 30 43 54
19.2 32.6 42.8 59.3 99 148 182.3
21.6 30.9 38.3 49.1 72.1 105.9 147
5355 5126 4820 4820 4055 3672 3290
6300 6030 5670 5670 4770 4320 3870
0.28 0.59 0.85 1.15 2.15 4.9 11.5
61818 61918 16018 6018 6218 6318 6418
49
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
50
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
95
120 130 145 145 170 200
13 18 16 24 32 45
19.6 33.2 43.9 62.5 111.8 155.9
22.4 32.9 40.7 53 79.9 115.7
5126 4820 4590 4590 3825 3443
6030 5670 5400 5400 4500 4050
0.3 0.61 0.89 1.2 2.6 5.65
61819 61919 16019 6019 6219 6319
100
125 140 150 150 180 215
13 20 16 24 34 47
19.6 41.5 45.3 62.5 124.5 170.6
23.6 40.2 43.2 53 91.15 137.3
4820 4590 4284 4284 3672 3290
5670 5400 5040 5040 4320 3870
0.31 0.83 0.91 1.25 3.15 7
61820 61920 16020 6020 6220 6320
105
130 145 160 160 190 225
13 20 18 26 36 49
20.4 43.4 53 74.6 137.3 178.4
19.3 43.2 50 64.2 102 150
4820 4284 4055 4055 3443 3060
5670 5040 4770 4770 4050 3600
0.32 0.87 1.2 1.6 3.7 8.25
61821 61921 16021 6021 6221 6321
110
140 150 170 170 200 240
16 20 19 28 38 50
27.6 42.8 58.9 83.5 148 199
25.5 44.2 55.9 72.1 115.7 176.5
4284 4284 3825 3825 3290 2907
5040 5040 4500 4500 3870 3420
0.6 0.9 1.45 1.95 4.35 9.55
61822 61922 16022 6022 6222 6322
120
150 165 180 180 215 260
16 22 19 28 40 55
28.6 54.2 62.5 86.7 143.1 203.9
27.6 55.9 62.9 78.5 115.7 182.3
4055 3825 3672 3672 3060 2601
4770 4500 4320 4320 3600 3060
0.65 1.2 1.6 2.05 5.15 12.5
61824 61924 16024 6024 6224 6324
130
165 180 200 200 230 280
18 24 22 33 40 58
36.9 63.7 81.6 109.8 152.9 224.5
42.2 65.7 79.9 98 129.4 211.7
3672 3443 3290 3290 2754 3443
4320 4050 3870 3870 3240 4050
0.93 1.85 2.35 3.15 5.8 17.5
61826 61926 16026 6026 6226 6326 M
140
175 190 210 210 250 300
18 24 22 33 42 62
38.3 65 79 108.8 161.8 246
45.6 70.6 84.8 105.9 147 240.2
3443 4284 3060 3060 2601 3290
4050 5040 3600 3600 3060 3870
0.99 1.7 2.5 3.35 7.45 22
61828 61928 MA 16028 6028 6228 6328 M
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
150
190 210 225 225 270 320
20 28 24 35 45 65
47.9 86.7 90.4 122.6 170.6 270.5
59.8 91.2 96.1 1226 162.7 279.4
3290 4055 2907 2907 2448 3060
3870 4770 3420 3420 2880 3600
1.4 3.05 3.15 4.8 9.4 26
61830 61930 MA 16030 6030 6230 6330 M
160
200 220 240 240 240 290 340
20 28 25 38 38 48 68
48.5 90.5 97.6 140.2 140.2 182.3 270.5
62.8 96.1 105.9 140.2 140.2 182.3 279.3
3060 3825 2754 2754 3672 2295 2907
3600 4500 3240 3240 4320 2700 3420
1.4 3.2 3.7 5.9 5.9 14 29
61832 61932 MA 16032 6032 6032 M 6232 6332 M
170
215 230 260 260 310 360
22 28 28 42 52 72
60.6 91.8 116.7 164.7 207.8 305.8
76.5 103.9 126.5 169.6 219.7 334
2754 3672 2448 3290 2907 2601
3240 4320 2880 3870 3420 3060
1.9 3.4 5 7.9 17.5 34.5
61834 61934 MA 16034 6034 M 6234 M 6334 M
180
225 250 280 280 320 380
22 33 31 46 52 75
61.2 116.7 135.3 186.3 224.5 344
80 1312 143 197 236 397
2601 3290 3060 3060 2754 2448
3060 3870 3600 3600 3240 2880
2 5.05 6.6 10.5 18.5 42.5
61836 61936 MA 16036 6036 M 6236 M 6336 M
190
240 260 290 290 340 400
24 33 31 46 55 78
74.6 114.7 145.1 191.2 245 363.6
96 133 163 212 275 422
2448 3290 2295 2907 2601 2295
2880 3870 2700 3420 3060 2700
2.6 5.25 7.9 11 23 49
61838 61938 MA 16038 6038 M 6238 M 6338 M
200
250 280 310 310 360
24 38 34 51 58
74.6 145.1 164.7 211.7 264.7
100 163 186 240 304
2448 2907 2142 2754 2448
2880 3420 2520 3240 2880
2.7 7.4 8.85 14 28
61840 61940 MA 16040 6040 M 6240 M
220
270 300 340 340 400 460
24 38 37 56 65 88
76.5 148 170.6 242.1 290.1 401.9
108 177 200 285 358 510
2142 2754 1836 2448 2295 1989
2520 3240 2160 2880 2700 2340
3 8 11.5 18.5 37 72.5
61844 61944 MA 16044 6044 M 6244 M 6344 M
240
300 320 360
28 38 37
105.9 155.9 174.5
147 196 216
1989 2448 2295
2340 2880 2700
4.5 8.6 145
61848 61948 MA 16048 MA
51
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
52
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
240
360 440 500
56 72 95
250 350.9 433.2
309 456 574
2295 1989 1836
2700 2340 2160
19 51 92.5
6048 M 6248 M 6348 M
260
320 360 400 400 480 540
28 46 44 65 80 102
108.8 207.8 233.3 285.2 382.3 496.9
160 265 304 368 520 696
1836 2295 2142 2142 1836 1683
2160 2700 2520 2520 2160 1980
4.8 14.5 21.5 29.5 65 115
61852 61952 MA 16052 MA 6052 M 6252 M 6352 M
280
350 380 420 420 500
33 46 44 65 80
135.3 211.7 237.2 296 414.6
197 279 329 397 588
1683 2142 1989 1989 1683
1980 2520 2340 2340 1980
7.4 15 23 31 71
61856 61956 MA 16056 MA 6056 M 6256 M
300
380 420 460 460 540
38 56 50 74 85
168.6 264.7 280.3 350.9 452.8
241 368 397 491 657
1989 1836 1836 1836 1530
2340 2160 2160 2160 1800
10.5 24.5 32 44 88.5
61860 MA 61960 MA 16060 MA 6060 M 6260 M
320
400 440 480 480
38 56 50 74
168.6 270.5 275.4 363.6
250 393 397 530
1836 1836 1683 1683
2160 2160 1980 1980
11 25.5 34 46
61864 MA 61964 MA 16064 MA 6064 M
340
420 460 520 520
38 56 57 82
174.5 275.4 338.2 414.6
270 417 510 628
1836 1683 1530 1530
2160 1980 1800 1800
11.5 26.5 45 62
61868MA 61968MA 16068MA 6068M
360
440 480 540 540
38 56 57 82
178.4 285.2 344 452.8
280 442 539 721
1683 1683 1454 1454
1980 1980 1710 1710
12 28 49 64.5
61872 MA 61972 MA 16072 MA 6072 M
380
480 520 560 560
46 65 57 82
237.2 331.3 369.5 452.8
382 530 608 735
1530 1454 1377 1377
1800 1710 1620 1620
20 40 51 67.5
61876 MA 61976 MA 16076 MA 6076 M
400
500 540 600
46 65 90
242.1 338.2 509.7
397 559 848
1454 1377 1301
1710 1620 1530
20.5 41.5 87.5
61880 MA 61980 MA 6080 M
420
520 560 620
46 65 90
246 344 496.9
417 589 863
1377 1377 1224
1620 1620 1440
21.5 43 91.5
61884 MA 61984 MA 6084 M
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
440
540 540 600 600 650
31 46 50 74 94
155 250 305 401.9 542
285 432 550 706 946
870 1377 870 1224 1148
1000 1620 1000 1440 1350
16.5 22.5 41 60.5 105
60888 61888 MA 60988 61988 MA 6088 M
460
580 620 620 680
56 72 74 100
312.7 410 414.6 570.4
559 765 735 1039
1224 870 1224 1148
1440 1100 1440 1350
35 63 62.5 120
61892 MA 61992 61992 MA 6092 MB
480
600 650 700
56 78 100
318.6 440.1 605.7
588 799 1117
1224 1148 1071
1440 1350 1260
36.5 74 125
61896 MA 61996 MA 6096 MB
500
620 620 660 670 720
37 56 75 78 100
220 325.4 440 452.8 593
445 608 720 848 1117
800 1148 750 1071 995
950 1350 900 1260 1170
20 40.5 68.8 77 135
608/500 618/500 MA 619/500X3F1 619/500 MA 60/500 N1MAS
530
650 710 710 780
56 57 82 112
325.4 410 478.3 637
645 810 912 1245
1071 690 995 918
1260 840 1170 1080
39.5 60 90.5 185
618/530 MA 609/530 619/530 MA 60/530 N1MAS
560
680 680 750 820
37 56 85 115
220 338.2 484.2 649.8
460 682 961 1441
710 995 918 918
860 1170 1080 1080
30 42 105 210
608/560 618/560 MA 619/560 MA 60/560 N1MAS
600
730 730 800 870
42 60 90 118
260 356.8 573.4 692
550 750 1197 1450
670 918 842 600
800 1080 990 700
41 52 125 233
608/600 618/600 MA 619/600 MA 60/600/HC
630
780 780 850 850 920
48 69 71 100 128
355 433.2 475 611.6 802.7
765 946 1050 1314 1725
640 842 600 842 765
760 990 710 990 900
41 73 112 160 285
608/630 618/630 MA 609/630 619/630 N1MA 60/630 N1MAS
670
820 900 980
69 103 136
433.2 662.5 886
980 1470 1999
842 765 689
990 900 810
83.5 185 345
618/670 MA 619/670 MA 60/670 N1MAS
710
870 950 950 1030
74 78 106 140
465.6 545 649.8 936.9
1078 1280 1470 2157
765 500 689 650
900 610 810 765
93.5 148 220 375
618/710 MA 609/710 619/710 MA 60/710 MA
750
920 1000 1090
78 112 150
516.5 745.8 975
1226 1765 2370
689 650 450
810 765 530
110 255 490
618/750 MA 619/750 MA 60/750
53
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS, SINGLE ROW
Dimensiones (mm) Dimension (mm) d (mm)
54
D (mm)
B (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Sigla Weight (Kg) Designation
800
980 980 1060 1150
57 82 115 155
390 547.9 815.4 989.9
990 1343 2000 2500
430 650 612 574
510 765 720 675
100 130 275 535
608/800 618/800 MA 619/800 MA 60/800 N1MAS
850
1030 1030 1120 1220
57 82 118 165
385 547.9 815 1090
1000 1402 2150 2980
450 574 400 370
500 675 480 430
75 140 315 640
608/850 618/850 MA 619/850 60/850
900
1090 1180 1280
85 122 170
605.7 830 1080
1567 2270 3120
536 360 330
630 440 410
160 355 725
618/900 MA 619/900 60/900
950
1150 1250 1360
90 132 180
663 985 1145
1620 2850 3315
360 330 310
430 410 380
188 395 850
618/950F1 619/950 60/950
1000
1220 1220 1320 1320 1420
71 100 103 140 185
540 624.3 800 985 1320
1550 1765 2340 2880 3900
350 459 330 330 280
400 540 380 380 340
175 245 405 525 925
608/1000 618/1000 MA 609/1000 619/1000 60/1000
1060
1280 1400 1500
100 150 195
713.5 985 1320
2077.7 3030 3860
428 290 250
504 330 330
260 615 1090
618/1060 MA 619/1060 60/1060
1120
1360 1460 1580
106 150 200
726.2 1010 1430
2157 3070 4480
405 270 250
477 330 300
315 640 1245
618/1120 MA 619/1120 60/1120
1180
1420 1540
106 160
745.8 1115
2312.9 3630
367 210
432 270
330 765
618/1180 MB 619/1180
1250
1500
112
830
2740
210
270
390
618/1250
1280
1560
150
939
2750
220
280
606
66/1280F1
1320
1600 1720
122 128
955 1180
2830 4060
200 190
260 230
512 835
618/1320F3 609/1320
1400
1700 1820
132 185
1070 1550
3980 5520
190 180
230 230
620 1260
618/1400 619/1400
1500
1820 1950
140 195
1685.7 1680
5980 6220
245 160
288 190
690 1515
618/1500 MB 619/1500
1600
1950 2060
155 200
1240 1820
4750 6880
150 140
180 170
975 1660
618/1600 619/1600
1700
2060 2180
160 212
1240 1950
4950 7680
130 120
160 150
1110 1930
618/1700 619/1700
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
d (mm)
D (mm)
3
10 10
4 4
0.53 0.53
0.18 0.18
57000 38000
0.0015 0.0015
623-Z 623-RS
623-ZZ 623-2RS
4
9 9 11 12 13 16 16 16
3.5 4 4 4 5 5 5 5
0.53 0.53 0.71 0.79 0.92 1.09 1.09 1.09
0.18 0.18 0.23 0.28 0.29 0.38 0.38 0.38
66500 66500 59850 57000 50350 45600 45600 26600
0.001 0.0013 0.0017 0.0021 0.0031 0.0054 0.0054 0.0054
604-Z 624-Z 634-Z 634-RZ 634-RS
628/4-ZZ 638/4-ZZ 619/4-ZZ 604-ZZ 624-ZZ 634-ZZ 634-2RZ 634-2RS
5
11 11 13 16 19 19 19
4 5 4 5 6 6 6
0.63 0.63 0.87 1.12 2.3 2.3 2.3
0.25 0.25 0.34 0.38 0.94 0.94 0.94
57000 57000 50350 45600 38000 38000 22800
0.0014 0.0016 0.0025 0.005 0.009 0.009 0.009
625-Z 635-Z 635-RZ 635-RS
628/5-ZZ 638/5-ZZ 619/5-ZZ 625-ZZ 635-ZZ 635-2RZ 635-2RS
6
13 15 19 19
5 5 6 6
0.87 1.22 2.3 2.3
0.34 0.47 0.94 0.94
50350 47500 38000 22800
0.0026 0.0039 0.0084 0.0084
626-Z 626RS
628/6-ZZ 619/6-ZZ 626-ZZ 626-2RS
7
14 17 19 19 22 22
5 5 6 6 7 7
0.94 1.46 2.3 2.3 3.39 3.39
0.4 0.55 0.94 0.94 1.35 1.35
47500 42750 40850 22800 34200 20900
0.0031 0.0049 0.0075 0.0075 0.013 0.012
607-Z 607-RS 627-Z 627-RS
628/7-ZZ 619/7-ZZ 607-ZZ 607-2RS 627-ZZ 627-2RS
8
16 16 16 19 19 22 22 22 24 24 24 28
5 5 6 6 6 7 7 11 8 8 8 9
1.31 1.31 1.31 1.87 1.87 3.39 3.39 3.39 3.83 3.83 3.83 4.53
0.56 0.56 0.56 0.73 0.73 1.35 1.35 1.35 1.63 1.63 1.63 1.93
42750 24700 42750 38000 22800 36100 20900 20900 30400 30400 18050 28500
0.0036 0.0036 0.0043 0.0071 0.0071 0.012 0.012 0.016 0.017 0.017 0.017 0.03
608-Z 608-RS 628-Z 628-RZ 628-RS 638-RZ
628/8-ZZ 628/8-2RS 638/8-ZZ 619/8-ZZ 619/8-2RS 608-ZZ 608-2RS 630/8-2RS 628-ZZ 628-2RZ 628-2RS 638-2RZ
9
17 17 20 24 24
5 5 6 7 7
1.41 1.41 2.04 3.83 3.83
0.63 0.63 0.85 1.63 1.63
40850 22800 36100 32300 18050
0.0043 0.0043 0.0076 0.014 0.014
628/9-Z 609-Z 609-RS
628/9-ZZ 628/9-2RS 619/9-ZZ 609-ZZ 609-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
55
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm)
56
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
d (mm)
D (mm)
9
26 26
8 8
4.66 4.66
1.93 1.93
28500 18050
0.02 0.02
629-Z 629-RS
629-ZZ 629-2RS
10
15 19 19 19 22 22 26 26 26 28 30 30 30 35 35 35
4 5 5 7 6 6 8 8 12 8 9 9 14 11 11 17
66 1.36 1.36 133 2.04 2.04 4.66 4.66 4.53 4.53 5.3 5.3 4.97 8.35 8.35 7.9
34 0.58 0.58 0.56 0.84 0.84 1.93 1.93 1.93 1.93 2.32 2.32 2.32 3.34 3.34 3.34
36000 36100 20900 34000 34200 19000 32300 18050 18050 30400 26600 16150 16150 24700 14250 14250
0.0055 0.0055 0.0055 0.0055 0.01 0.01 0.019 0.019 0.025 0.022 0.032 0.032 0.04 0.053 0.053 0.06
6000-Z 6000-RS 6200-Z 6200-RS
61700ZZ 61800-ZZ 61800-2RS 63800ZZ 61900-ZZ 61900-2RS 6000-ZZ 6000-2RS 63000-2RS 16100-ZZ 6200-ZZ 6200-2RS 62200-2RS 6300-ZZ 6300-2RS 62300-2RS
12
18 21 21 21 24 24 28 28 28 30 30 32 32 32 37 37 37
4 5 5 7 6 6 8 8 12 8 8 10 10 14 12 12 17
72 1.41 1.41 149 2.21 2.21 5.3 5.3 4.97 4.97 4.97 7.14 7.14 6.76 9.9 9.9 9.56
41 0.66 0.66 0.68 0.97 0.97 2.32 2.32 2.32 2.32 2.32 3.04 3.04 3.04 4.07 4.07 4.07
31000 34200 19000 30500 30400 18050 28500 16150 16150 26600 15200 24700 14250 14250 20900 13300 13300
0.0063 0.0063 0.0063 0.0063 0.011 0.011 0.022 0.022 0.029 0.023 0.023 0.037 0.037 0.045 0.06 0.06 0.07
6001-Z 6001-RS 6201-Z 6201-RS 6301-Z 6301-RS
61701-ZZ 61801-ZZ 61801-2RS 63801-ZZ 61901-ZZ 61901-2RS 6001-ZZ 6001-2RS 63001-2RS 16101-ZZ 16101-2RS 6201-ZZ 6201-2RS 62201-2RS 6301-ZZ 6301-2RS 62301-2RS
15
21 24 24 24 28 28 28 32 32 32 32 35
4 5 5 7 7 7 7 8 9 9 13 11
81 1.53 1.53 162 4.28 4.28 4.28 5.74 5.74 5.74 5.48 7.9
44 0.79 0.79 0.79 2.2 2.2 2.2 2.8 2.8 2.8 2.8 3.68
27000 28500 16150 26000 26600 26600 15200 24700 24700 13300 13300 20900
0.0074 0.0074 0.0074 0.016 0.016 0.016 0.016 0.025 0.03 0.03 0.039 0.045
16002-Z 6002-Z 6002-RS 6202-Z
61702-ZZ 61802-ZZ 61802-2RS 613802-ZZ 61902-ZZ 61902-2RZ 61902-2RS 16002-ZZ 6002-ZZ 6002-2RS 63002-2RS 6202-ZZ
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
6300-Z 6300-RS
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Blindaje de un lado One side shield
Peso (Kg) Weight (Kg)
Blindaje en ambos lados Two side shield
D (mm)
B (mm)
15
35 35 42 42 42
11 14 13 13 17
7.9 7.65 11.67 11.67 11.18
3.68 3.68 5.3 5.3 5.3
12350 12350 18050 11400 11400
0.045 0.054 0.082 0.082 0.11
6202-RS 6302-Z 6302-RS -
6202-2RS 62202-2RS 6302-ZZ 6302-2RS 62302-2RS
17
23 26 26 26 26 30 30 30 35 35 35 35 40 40 40 47 47 47
4 5 5 5 7 7 7 7 8 10 10 14 12 12 16 14 14 19
80 1.65 1.65 1.65 175 4.53 4.53 4.53 6.25 6.25 6.25 5.93 9.76 9.76 9.37 14.02 14.02 13.23
50 0.92 0.92 0.92 0.90 2.5 2.5 2.5 3.19 3.19 3.19 3.19 4.66 4.66 4.66 6.42 6.42 6.42
25000 26600 26600 15200 24000 24700 24700 13300 20900 20900 12350 12350 18050 11400 11400 16150 10450 10450
0.0082 0.0082 0.0082 0.0082 0.0082 0.018 0.018 0.018 0.032 0.039 0.039 0.052 0.065 0.065 0.083 0.12 0.12 0.15
6003-Z 6003-RS 6203-Z 6203-RS 6303-Z 6303-RS -
61703-ZZ 61803-ZZ 61803-2RZ 61803-2RS 63803-ZZ 61903-ZZ 61903-RZ 61903-2RS 16003-ZZ 6003-ZZ 6003-2RS 63003-2RS 6203-ZZ 6203-2RS 62203-2RS 6303-ZZ 6303-2RS 62303-2RS
20
27 32 32 37 37 42 42 42 47 47 47 52 52 52
4 7 7 9 9 12 12 16 14 14 18 15 15 21
84 3.95 3.95 6.25 6.25 9.76 9.76 9.18 13.23 13.23 12.45 16.47 16.47 15.59
57 2.28 2.28 3.58 3.58 4.9 4.9 4.9 6.42 6.42 6.42 7.65 7.65 7.65
21000 20900 12350 19000 11400 18050 10450 10450 16150 9500 9500 14250 9025 9025
0.018 0.018 0.018 0.038 0.038 0.069 0.069 0.086 0.11 0.11 0.13 0.14 0.14 0.2
6004-Z 6004-RS 6204-Z 6204-RS 6304-Z 6304-RS -
61704-ZZ 61804-2RZ 61804-2RS 61904-2RZ 61904-2RS 6004-ZZ 6004-2RS 63004-2RS 6204-ZZ 6204-2RS 62204-2RS 6304-ZZ 6304-2RS 62304-2RS
22
50
14
13.72
7.5
8550
0.12
-
62/22-2RS
25
32 37 37 42 42 47 47 47
4 7 7 9 9 12 12 16
90 4.28 4.28 6.88 6.88 11.67 11.67 10.98
66 2.55 2.55 4.22 4.22 6.42 6.42 6.42
19000 18050 10450 17100 9500 15200 9025 9025
23000 0.022 0.022 0.045 0.045 0.08 0.08 0.1
6005-Z 6005-RS -
61705ZZ 61805-2RZ 61805-2RS 61905-2RZ 61905-2RS 6005-ZZ 6005-2RS 63005-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
57
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
58
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
D (mm)
B (mm)
25
52 52 52 62 62 62 62
15 15 18 17 17 17 24
14.51 14.51 13.72 22.94 22.94 22.94 22.05
7.65 7.65 7.65 11.37 11.37 11.37 11.37
13300 8075 8075 12350 12350 7125 7125
0.13 0.13 0.15 0.23 0.23 0.23 0.32
6205-Z 6205-RS 6305-Z 6035-RZ 6035-RS -
6205-ZZ 6205-2RS 62205-2RS 6305-ZZ 6305-2RZ 6305-2RS 62305-2RS
30
37 42 42 47 47 55 55 55 55 62 62 62 62 72 72 72 72
4 7 7 9 9 13 13 13 19 16 16 16 20 19 19 19 27
95 4.41 4.41 7.14 7.14 13.53 13.53 13.53 13.04 19.9 19.9 19.9 19.11 29.01 29.01 29.01 27.54
76 2.85 2.85 4.46 4.46 8.14 8.14 8.14 8.14 10.98 10.98 10.98 10.98 15.68 15.68 15.68 15.68
17000 15200 9025 14250 8075 13300 13300 7600 7600 11400 11400 7125 7125 10450 10450 5985 5985
0.027 0.027 0.027 0.051 0.051 0.12 0.12 0.12 0.16 0.2 0.2 0.2 0.24 0.35 0.35 0.35 0.48
6006-Z 6006-RZ 6006-RS 6206-Z 6206-RZ 6206-RS 6306-Z 6306-RZ 6306-RS -
61706ZZ 61806-2RZ 61806-2RS 61906-2RZ 61906-2RS 6006-ZZ 6006-2RZ 6006-2RS 63006-2RS 6206-ZZ 6206-2RZ 6206-2RS 62206-2RS 6306-ZZ 6306-2RZ 6306-2RS 62306-2RS
35
44 47 47 55 55 62 62 62 62 72 72 72 80 80 80
5 7 7 10 10 14 14 14 20 17 17 23 21 21 31
155 4.66 4.66 9.37 9.37 16.47 16.47 16.47 15.59 26.46 26.46 24.99 34.4 34.4 32.54
130 3.14 3.14 6.67 6.67 10 10 10 10 15 15 15 18.62 18.62 18.62
14000 13300 7600 12350 7125 11400 11400 6650 6650 9500 5985 5985 9025 5700 5700
0.03 0.03 0.03 0.08 0.08 0.16 0.16 0.16 0.21 0.29 0.29 0.37 0.46 0.46 0.66
6007-Z 6007-RZ 6007-RS 6207-Z 6207-RS 6307-Z 6307-RS
61707ZZ 61807-2RZ 61807-2RS 61907-2RZ 61907-2RS 6007-ZZ 6007-2RZ 6007-2RS 63007-2RS 6207-ZZ 6207-2RS 62207-2RS 6307-ZZ 6307-2RS 62307-2RS
40
50 52 52 62 62 68 68 68
6 7 7 12 12 15 15 15
207 4.85 4.85 13.53 13.53 17.45 17.45 17.45
177 3.39 3.39 9.8 9.8 11.37 11.37 11.37
13000 12350 7125 11400 6365 10450 10450 5985
0.034 0.034 0.034 0.12 0.12 0.19 0.19 0.19
6008-Z 6008-RZ 6008-RS
61708ZZ 61808-2RZ 61808-2RS 61908-2RZ 61908-2RS 6008-ZZ 6008-2RZ 6008-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
D (mm)
B (mm)
40
68 80 80 80 80 90 90 90 90
21 18 18 18 23 23 23 23 33
16.47 31.85 31.85 31.85 30.09 41.46 41.46 41.46 40.18
11.37 18.62 18.62 18.62 18.62 23.52 23.52 23.52 23.52
5985 8550 8550 5320 5320 8075 8075 4750 4750
0.26 0.37 0.37 0.37 0.44 0.63 0.63 0.63 0.89
6208-RZ 6208-Z 6208-RS 6308-Z 6308-RZ 6308-RS -
63008-2RS 6208-2RZ 6208-ZZ 6208-2RS 62208-2RS 6308-ZZ 6308-2RZ 6308-2RS 62308-2RS
45
55 58 58 68 68 75 75 75 85 85 85 100 100 100
6 7 7 12 12 16 16 23 19 19 23 25 25 36
213 6.5 6.5 13.72 13.72 21.66 21.66 20.39 34.4 34.4 32.54 54.2 54.2 51.65
192 5.98 5.98 10.59 10.59 14.31 14.31 14.31 21.17 21.17 21.17 30.87 30.87 30.87
12000 10450 6365 9500 5700 9500 5320 5320 8075 4750 4750 7125 4275 4275
0.04 0.04 0.04 0.14 0.14 0.25 0.25 0.34 0.41 0.41 0.48 0.83 0.83 1.15
6009-Z 6009-RS 6209-Z 6209-RS 6309-Z 6309-RS -
61709-ZZ 61809-2RZ 61809-2RS 61909-2RZ 61909-2RS 6009-ZZ 6009-2RS 63009-2RS 6209-ZZ 6209-2RS 62209-2RS 6309-ZZ 6309-2RS 62309-2RS
50
65 65 72 72 80 80 80 80 90 90 90 90 110 110 110
7 7 12 12 16 16 16 23 20 20 20 23 27 27 40
6.63 6.63 14.31 14.31 22.45 22.45 22.45 21.17 36.36 36.36 36.36 34.4 63.7 63.7 60.57
6.67 6.67 11.57 11.57 15.68 15.68 15.68 15.68 22.74 22.74 22.74 22.74 37.24 37.24 37.24
9500 5700 9025 5320 8550 8550 4750 4750 7600 7600 4560 4560 6365 4085 4085
0.052 0.052 0.14 0.14 0.26 0.26 0.26 0.37 0.46 0.46 0.46 0.52 1.05 1.05 1.55
6010-Z 6010-RZ 6010-RS 6210-Z 6210-RZ 6210-RS 6310-Z 6310-RS -
61810-2RZ 61810-2RS 61910-2RZ 61910-2RS 6010-ZZ 6010-2RZ 6010-2RS 63010-2RS 6210-ZZ 6210-2RZ 6210-2RS 62210-2RS 6310-ZZ 6310-2RS 62310-2RS
55
72 72 80 80 90 90 100 100 100
9 9 13 13 18 18 21 21 25
8.86 8.86 16.17 16.17 29.01 29.01 45.28 45.28 42.73
8.63 8.63 13.72 13.72 20.78 20.78 28.42 28.42 28.42
9025 5035 8075 4750 7600 4275 6650 4085 4085
0.083 0.083 0.19 0.19 0.39 0.39 0.61 0.61 0.7
6011-Z 6011-RS 6211-Z 6211-RS -
61811-2RZ 61811-2RS 61911-2RZ 61911-2RS 6011-ZZ 6011-2RS 6211-ZZ 6211-2RS 62211-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
59
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
B (mm)
Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
55
120 120 120
29 29 43
72.62 72.62 70.07
44.1 44.1 44.1
5985 3610 3610
1.35 1.35 1.95
6311-Z 6311-RS -
6311-ZZ 6311-2RS 62311-2RS
60
78 78 85 85 95 95 95 110 110 110 130 130 130
10 10 13 13 18 18 18 22 22 28 31 31 46
11.67 11.67 16.17 16.17 30.09 30.09 30.09 54.2 54.2 51.65 83.5 83.5 80.27
11.18 11.18 14.02 14.02 22.74 22.74 22.74 35.28 35.28 35.28 50.96 50.96 50.96
8075 4560 7600 4275 7125 7125 4085 5985 3800 3800 5320 3230 3230
0.11 0.11 0.2 0.2 0.42 0.42 0.42 0.78 0.78 0.97 1.7 1.7 2.5
6012-Z 6012-RZ 6012-RS 6212-Z 6212-RS 6312-Z 6312-2RS -
61812-2RZ 61812-2RS 61912-2RZ 61912-2RS 6012-ZZ 6012-2RZ 6012-2RS 6212-ZZ 6212-2RS 62212-2RS 6312-ZZ 6312-2RS 62312-2RS
65
85 85 90 90 100 100 120 120 120 140 140 140
10 10 13 13 18 18 23 23 31 33 33 48
12.16 12.16 17.06 17.06 31.27 31.27 57.33 57.33 54.79 95.55 95.55 90.46
12.45 12.45 15.68 15.68 24.5 24.5 39.69 39.69 39.69 58.8 58.8 58.8
7600 4275 7125 4085 6650 3800 5700 3420 3420 5035 3040 3040
0.13 0.13 0.22 0.22 0.44 0.44 0.99 0.99 1.25 2.1 2.1 3
6013-Z 6013-RS 6213-Z 6213-RS 6313-Z 6313-RS -
61813-2RZ 61813-2RS 61913-2RZ 61913-2RS 6013-ZZ 6013-2RS 6213-ZZ 6213-2RS 62213-2RS 6313-ZZ 6313-2RS 62313-2RS
70
90 90 100 100 110 110 125 125 125 150 150 150
10 10 16 16 20 20 24 24 31 35 35 51
12.16 12.16 23.33 23.33 38.91 38.91 62.43 62.43 59.29 108.78 108.78 101.92
12.94 12.94 20.78 20.78 30.38 30.38 44.1 44.1 44.1 66.64 66.64 66.64
7125 4085 6650 3800 5985 3420 5320 3230 3230 4750 2850 2850
0.14 0.14 0.35 0.35 0.6 0.6 1.1 1.1 1.3 2.5 2.5 3.55
6014-Z 6014-RS 6214-Z 6214-RS 6314-Z 6314-RS -
61814-2RZ 61814-2RS 61914-2RZ 61914-2RS 6014-ZZ 6014-2RS 6214-ZZ 6214-2RS 62214-2RS 6314-ZZ 6314-2RS 62314-2RS
75
95 95 105 105 115 115
10 10 16 16 20 20
12.45 12.45 23.72 23.72 40.77 40.77
14.02 14.02 18.92 18.92 32.83 32.83
6650 3800 5985 3420 5700 5700
0.15 0.15 0.37 0.37 0.64 0.64
6015-Z 6015-RZ
61815-2RZ 61815-2RS 61915-2RZ 61915-2RS 6015-ZZ 6015-2RZ
60
60
D (mm)
Coeficiente de carga (KN) Load rating (KN)
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
D (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
75
115 130 130 160 160
20 25 25 37 37
40.77 67.53 67.53 116.62 116.62
32.83 48.02 48.02 74.97 74.97
3230 5035 3040 4275 2660
0.64 1.2 1.2 3 3
6015-RS 6215-Z 6215-RS 6315-Z 6315-RS
6015-2RS 6215-ZZ 6215-2RS 6315-ZZ 6315-2RS
80
100 100 110 110 125 140 125 140 170 170
10 10 16 16 22 26 22 26 39 39
12.8 12.8 24.6 24.6 48.5 71.4 48.5 71.4 127.4 127.4
14.7 14.7 20 20 39.2 53.9 39.2 53.9 84.8 84.8
5985 3420 5700 3230 3040 4560 5320 2850 4085 2470
0.15 0.15 0.4 0.4 0.85 1.4 0.85 1.4 3.6 3.6
6016-RS 6216-Z 6016-Z 6216-RS 6316-Z 6316-RS
61816-2RZ 61816-2RS 61916-2RZ 61916-2RS 6016-2RS 6216-ZZ 6016-ZZ 6216-2RS 6316-ZZ 6316-2RS
85
110 110 130 130 150 150 180 180
13 13 22 22 28 28 41 41
19.2 19.2 51 51 85.4 85.4 137.2 137.2
20.4 20.4 42.2 42.2 62.8 62.8 94.6 94.6
5700 3230 5035 2850 4275 2660 3800 2280
0.27 0.27 0.89 0.89 1.8 1.8 4.25 4.25
6017-Z 6017-RS 6217-Z 6217-RS 6317-Z 6317-RS
61817-2RZ 61817-2RS 6017-ZZ 6017-2RS 6217-ZZ 6217-2RS 6317-ZZ 6317-2RS
90
115 115 140 140 160 160 190 190
13 13 24 24 30 30 43 43
19.2 19.2 59.3 59.3 99 99 148 148
21.6 21.6 49 49 72.1 72.1 105.9 105.9
5320 3040 4750 2660 4085 2470 3610 2280
0.28 0.28 1.15 1.15 2.15 2.15 4.9 4.9
6018-Z 6018-RS 6218-Z 6218-RS 6318-Z 6318-RS
61818-2RZ 61818-2RS 6018-ZZ 6018-2RS 6218-ZZ 6218-2RS 6318-ZZ 6318-2RS
95
120 120 130 145 145 170 170 200 200
13 13 18 24 24 32 32 45 45
19.6 19.6 33.2 62.5 62.5 111.8 111.8 155.9 155.9
22.4 22.4 32.9 53 53 79.9 79.9 115.7 115.7
5035 2850 2850 4560 2660 3800 2280 3420 2090
0.3 0.3 0.61 1.2 1.2 2.6 2.6 5.65 5.65
6019-Z 6019-RS 6219-Z 6219-RS 6319-Z 6319-RS
61819-2RZ 61819-2RS 61919-2RS 6019-ZZ 6019-2RS 6219-ZZ 6219-2RS 6319-ZZ 6319-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
61
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS SEALED RADIAL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
62
D (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Sigla Designation Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Blindaje de un lado One side shield
Blindaje en ambos lados Two side shield
100
125 125 150 150 180 180
13 13 24 24 34 34
19.6 19.6 62.5 62.5 124.5 124.5
23.6 23.6 53 53 91.2 91.2
5035 2850 4275 2470 3610 2280
0.31 0.31 1.25 1.25 3.15 3.15
6020-Z 6020-RS 6220-Z 6220-RS
61820-2RZ 61820-2RS 6020-ZZ 6020-2RS 6220-ZZ 6220-2RS
105
130 130 160 160 190 190 225
13 13 26 26 36 36 49
20.4 20.4 74.6 74.6 137.2 137.2 178.4
19.3 19.3 64.2 64.2 102 102 150
4750 2660 4085 2280 3420 2090 3040
0.32 0.32 1.6 1.6 3.7 3.7 8.25
6021-Z 6021-RS 6221-Z 6221-RS 6321-Z
61821-2RZ 61821-2RS 6021-ZZ 6021-2RS 6221-ZZ 6221-2RS 6321-ZZ
110
140 140 170 170 200
16 16 28 28 38
27.6 27.6 83.5 83.5 148
25.5 25.5 72.1 72.1 1095.7
4275 2470 3800 2280 3230
0.6 0.6 1.95 1.95 4.35
6022-Z 6022-RS 6222-Z
61822-2RZ 61822-2RS 6022-ZZ 6022-2RS 6222-ZZ
120
150 150 180 180 215
16 16 28 28 40
28.6 28.6 86.7 86.7 143.1
27.5 27.5 78.4 78.4 115.7
4085 2280 3610 2090 3040
0.65 0.65 2.05 2.05 5.15
6024-Z 6024-RS 6224-Z
61824-2RZ 61824-2RS 6024-ZZ 6024-2RS 6224-ZZ
130
165 165 200 200 230
18 18 33 33 40
37 37 109.8 109.8 152.9
42.2 42.2 98 98 129.4
3610 2090 3230 1900 2850
0.93 0.93 3.15 3.15 5.8
6026-Z 6026-RS 6226-Z
61826-2RZ 61826-2RS 6026-ZZ 6026-2RS 6226-ZZ
140
175 175 210 210
18 18 33 33
38.3 38.3 108.8 108.8
45.6 45.6 105.9 105.9
3420 1900 3040 1710
0.99 0.99 3.35 3.35
6028-Z 6028-RS
61828-2RZ 61828-2RS 6028-ZZ 6028-2RS
150
225 225
35 35
122.5 122.5
122.5 122.5
2850 1615
4.8 4.8
6030-Z 6030-RS
6030-ZZ 6030-2RS
160
240 240
38 38
140.2 140.2
140.2 140.2
2660 1520
5.9 5.9
6032-Z 6032-RS
6032-ZZ 6032-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, CON RANURADO PARA ARO DE FIJACIÓN SEALED RADIAL DEEP GROOVE BALL BEARINGS, WITH SNAP RING
Dimensiones (mm) Dimension (mm)
d (mm)
Coeficiente de carga (KN) Load rating (KN)
Dinámico D B b C f Dynamic (mm) (mm) (mm) (mm) (mm) C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Grease
Aceite Oil
Sigla Designation Peso (Kg) Weight (Kg) Con ranurado Con aro With snap With locating ring groove snap ring
Aro de fijación Snap ring
10
30
9
1.35
2.06
1.12
5.3
2.32
26010
30600
0.032
6200 N
6200 NR
SP 30
12
32
10
1.35
2.06
1.12
7.14
3.04
24480
28800
0.037
6201 N
6201 NR
SP 32
15
35
11
1.35
2.06
1.12
7.9
3.68
21420
25200
0.045
6202 N
6202 NR
SP 35
17
40 47
12 14
1.35 1.35
2.06 2.46
1.12 1.12
9.76 14.02
4.66 6.42
18360 16830
21600 19800
0.065 0.12
6203 N 6303 N
6203 NR 6303 NR
SP 40 SP 47
20
42 47 52
12 14 15
1.35 1.35 1.35
2.06 2.46 2.46
1.12 1.12 1.12
9.76 13.23 16.47
4.9 6.42 7.65
18360 15300 14535
21600 18000 17100
0.069 0.11 0.14
6004 N 6204 N 6304 N
6004 NR 6204 NR 6304 NR
SP 42 SP 47 SP 52
25
47 52 62
12 15 17
1.35 1.35 1.9
2.06 2.46 3.28
1.12 1.12 1.7
11.67 14.51 22.94
6.42 7.65 11.37
15300 13770 12240
18000 16200 14400
0.08 0.13 0.23
6005 N 6205 N 6305 N
6005 NR 6205 NR 6305 NR
SP 47 SP 52 SP 62
30
55 62 72
13 16 19
1.35 1.9 1.9
2.06 3.28 3.28
1.12 1.7 1.7
13.53 19.9 29.01
8.14 10.98 15.68
13005 11475 9945
15300 13500 11700
0.12 0.2 0.35
6006 N 6206 N 6306 N
6006 NR 6206 NR 6306 NR
SP 55 SP 62 SP 72
35
62 72 80 100
14 17 21 25
1.9 1.9 1.9 2.7
2.06 3.28 3.28 3.28
1.7 1.7 1.7 2.46
16.47 26.46 34.4 54.2
10 15 18.62 30.38
11475 9945 9180 7650
13500 11700 10800 9000
0.16 0.29 0.46 0.95
6007 N 6207 N 6307 N 6407 N
6007 NR 6207 NR 6307 NR 6407 NR
SP 62 SP 72 SP 80 SP 100
40
68 80 90 110
15 18 23 27
1.9 1.9 2.7 2.7
2.49 3.28 3.28 3.28
1.7 1.7 2.46 2.46
17.45 31.85 41.46 62.43
11.37 18.62 23.52 35.77
10710 8415 8415 6885
12600 9900 9900 8100
0.19 0.37 0.63 1.25
6008 N 6208 N 6308 N 6408 N
6008 NR 6208 NR 6308 NR 6408 NR
SP 68 SP 80 SP 90 SP 110
45
75 85 100 120
16 19 25 29
1.9 1.9 2.7 3.1
2.49 3.28 3.28 4.06
1.7 1.7 2.46 2.82
21.66 34.4 54.2 74.58
14.31 21.17 30.87 44.1
9180 8415 7268 6503
10800 9900 8550 7650
0.25 0.41 0.83 1.55
6009 N 6209 N 6309 N 6409 N
6009 NR 6209 NR 6309 NR 6409 NR
SP 75 SP 85 SP 100 SP 120
50
80 90 110 130
16 20 27 31
1.9 2.7 2.7 3.1
2.49 3.28 3.28
1.7 2.46 2.46 2.82
22.45 36.36 63.7 85.36
15.68 22.74 37.24 50.96
8415 7650 6503 5738
9900 9000 7650 6750
0.26 0.46 1.05 1.9
6010 N 6210 N 6310 N 6410 N
6010 NR 6210 NR 6310 NR 6410 NR
SP 80 SP 90 SP 110 SP 130
55
90 100 120 140
18 21 29 33
2.7 2.7 3.1 3.1
2.87 3.28 4.06 4.9
2.46 2.46 2.82 2.82
29.01 45.28 72.62 97.51
20.78 28.42 44.1 60.76
7650 6885 6120 5355
9000 8100 7200 6300
0.39 0.61 1.35 2.3
6011 N 6211 N 6311 N 6411 N
6011 NR 6211 NR 6311 NR 6411 NR
SP 90 SP 100 SP 120 SP 140
60
95 110 130 150
18 22 31 35
2.7 2.7 3.1 3.1
2.87 4.06 4.9 4.9
2.46 2.46 2.82 2.82
30.09 54.2 83.5 105.84
22.74 35.28 50.96 68.11
7268 6120 5355 4820
8550 7200 6300 5670
0.42 0.78 1.7 2.75
6012 N 6212 N 6312 N 6412 N
6012 NR 6212 NR 6312 NR 6412 NR
SP 95 SP 110 SP 130 SP 150
63
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, CON RANURADO PARA ARO DE FIJACIÓN SEALED RADIAL DEEP GROOVE BALL BEARINGS, WITH SNAP RING
Dimensiones (mm) Dimension (mm)
d (mm)
64
Coeficiente de carga (KN) Load rating (KN)
Dinámico D B b C f Dynamic (mm) (mm) (mm) (mm) (mm) C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Grease
Aceite Oil
Sigla Designation Peso (Kg) Weight (Kg) Con ranurado Con aro With snap With locating ring groove snap ring
Aro de fijación Snap ring
65
100 120 140 160
18 23 33 37
2.7 3.1 3.1 3.1
2.87 4.06 4.9 4.9
2.46 2.82 2.82 2.82
31.27 57.33 95.55 116.62
24.5 39.69 58.8 76.44
6885 5738 5126 4590
8100 6750 6030 5400
0.44 0.99 2.1 3.3
6013 N 6213 N 6313 N 6413 N
6013 NR 6213 NR 6313 NR 6413 NR
SP 100 SP 120 SP 140 SP 160
70
110 125 150
20 24 35
2.7 3.1 3.1
2.87 4.06 4.9
2.46 2.82 2.82
38.91 62.43 108.78
30.38 44.1 66.64
6120 5355 4820
7200 6300 5670
0.6 1.05 2.5
6014 N 6214 N 6314 N
6014 NR 6214 NR 6314 NR
SP 110 SP 125 SP 150
75
115 130 160
20 25 37
2.7 3.1 3.1
2.87 4.06 4.9
2.46 2.82 2.82
40.77 67.53 116.62
32.83 48.02 74.97
5738 5126 4284
6750 6030 5040
0.64 1.2 3
6015 N 6215 N 6315 N
6015 NR 6215 NR 6315 NR
SP 115 SP 130 SP 160
80
125 140
22 26
3.1 3.1
2.87 4.9
2.82 2.82
48.42 71.35
39.2 53.9
5355 4590
6300 5400
0.85 1.4
6016 N 6216 N
6016 NR 6216 NR
SP 125 SP 140
85
130 150
22 28
3.1 3.1
2.87 4.9
2.82 2.82
50.96 85.36
42.14 62.72
5126 4284
6030 5040
0.89 1.8
6017 N 6217 N
6017 NR 6217 NR
SP 130 SP 150
90
140 160
24 30
3.1 3.1
3.71 4.9
2.82 2.82
59.29 98.98
49 72.03
4820 4055
5670 4770
1.15 2.15
6018 N 6218 N
6018 NR 6218 NR
SP 140 SP 160
95
170
32
3.1
5.69
3.1
111.72
79.87
3825
4500
2.6
6219 N
6219 NR
SP 170
100
150 180
24 34
2.82 3.1
3.71 5.69
2.82 3.1
62.43 124.46
52.92 91.14
4284 3672
5040 4320
1.25 3.15
6020 N 6220 N
6020 NR 6220 NR
SP 150 SP 180
105
160
26
2.82
3.71
2.82
74.58
64.19
4055
4770
1.6
6021 N
6021 NR
SP 160
110
170
28
3.1
3.71
3.1
83.5
72.03
3825
4500
1.95
6022 N
6022 NR
SP 170
120
180
28
3.1
3.71
3.1
86.64
78.4
3672
4320
2.05
6024 N
6024 NR
SP 180
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS, BLINDADOS CON ARO DE FIJACIÓN RADIAL DEEP GROOVE BALL BEARINGS, SEALED WITH SNAP RING
Dimensiones (mm) Dimension (mm) d (mm)
10
D (mm)
30
B (mm)
Sigla Designation
Coeficiente de carga (KN) Load rating (KN) Dinámico Dynamic C
9
5.3
Estático Static C0 2.32
Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Abierto con blindaje en Open Shielded
Aro de fijación Snap ring
En ambos lados Un lado One side shield Two side shield 32300
0.032
6200-ZNR
6200-ZZNR
SP 30
12
32
10
7.14
3.04
30400
0.037
6201-ZNR
6201-ZZNR
SP 32
15
35
11
7.9
3.68
26600
0.045
6202-ZNR
6202-ZZNR
SP 35
17
40 47
12 14
9.76 14.02
4.66 6.42
22800 20900
0.065 0.12
6203-ZNR 6303-ZNR
6203-ZZNR 6303-ZZNR
SP 40 SP 47
20
42 47 52
12 14 15
9.76 13.23 16.47
4.9 6.42 7.65
22800 19000 18050
0.069 0.11 0.14
6004-ZNR 6204-ZNR 6304-ZNR
6004-ZZNR 6204-ZZNR 6304-ZZNR
SP 42 SP 47 SP 52
25
47 52 62
12 15 17
11.67 14.51 22.94
6.42 7.65 11.37
19000 17100 15200
0.08 0.13 0.23
6005-ZNR 6205-ZNR 6305-ZNR
6005-ZZNR 6205-ZZNR 6305-ZZNR
SP 47 SP 52 SP 62
30
62 72
16 19
19.9 29.01
10.98 15.68
14250 12350
0.2 0.35
6206-ZNR 6306-ZNR
6206-ZZNR 6306-ZZNR
SP 62 SP 72
35
72 80
17 21
26.46 34.4
15 18.62
12350 11400
0.29 0.46
6207-ZNR 6307-ZNR
6207-ZZNR 6307-ZZNR
SP 72 SP 80
40
80 90
18 23
31.85 41.46
18.62 23.52
10450 10450
0.37 0.63
6208-ZNR 6308-ZNR
6208-ZZNR 6308-ZZNR
SP 80 SP 90
45
85 100
19 25
34.4 54.2
21.17 30.87
10450 9025
0.41 0.83
6209-ZNR 6309-ZNR
6209-ZZNR 6309-ZZNR
SP 85 SP 100
50
90 110
20 27
36.36 63.7
22.74 37.24
9500 8075
0.46 1.05
6210-ZNR 6310-ZNR
6210-ZZNR 6310-ZZNR
SP 90 SP 110
55
100 120
21 29
45.28 72.62
28.42 44.1
8550 7600
0.61 1.35
6211-ZNR 6311-ZNR
6211-ZZNR 6311-ZZNR
SP 100 SP 120
60
110 130
22 31
54.2 83.5
35.28 50.96
7600 6650
0.78 1.7
6212-ZNR 6312-ZNR
6212-ZZNR 6312-ZZNR
SP 110 SP 130
65
120 140
23 33
57.33 95.55
39.69 58.8
7125 6365
0.99 2.1
6213-ZNR 6313-ZNR
6213-ZZNR 6313-ZZNR
SP 120 SP 140
70
125 150
24 35
62.43 108.78
44.1 66.64
6650 5985
1.05 2.5
6214-ZNR 6314-ZNR
6214-ZZNR 6314-ZZNR
SP 125 SP 150
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
65
Rodamientos rígidos de una hilera de bolas de acero inoxidable Radial stainless steel deep groove ball bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS
STAINLESS STEEL SINGLE ROW DEEP GROOVE
DE ACERO INOXIDABLE
RADIAL BALL BEARINGS
Los rodamientos ISB® rígidos de bolas de acero inoxidable resisten perfectamente a la corrosión provocada por la humedad. Este tipo específico de rodamiento rígido tiene las mismas características que el estándar de acero al cromo, por lo tanto encontraremos las mismas ranuras profundas y a elevados contactos. Sin escote de llenado, resisten a cargas axiales que inciden en las dos direcciones sumadas a cargas radiales, también en presencia de altas velocidades. Los rodamientos ISB® rígidos de bolas de acero inoxidable tienen las mismas características de funcionamiento que los rodamientos estándares con menor capacidad de carga. Los rodamientos ISB® rígidos de bolas de acero inoxidable se identifican con el prefijo SS.
ISB® stainless steel deep groove radial ball bearings are perfectly resistant to corrosion caused through moisture. This specific type of deep groove bearing has the same characteristics as the standard chromium steel bearing, therefore it has the same deep grooves and close conformities. They have no filling slots and withstand axial loads acting in both directions in addition to radial loads, even at high speeds. ISB® stainless steel deep groove radial ball bearings have the same operational characteristics as standard bearings but have a lower load carrying capacity. ISB® stainless steel deep groove radial ball bearings are identified with the designation prefix SS.
RODAMIENTOS ESTÁNDAR
STANDARD BEARINGS
Los rodamientos estándares ISB® se denominan abiertos cuando no tienen juntas laterales (Fig. 1).
The standard bearings of ISB® are open, because they have no seals at the sides (Fig. 1).
Fig. 1
RODAMIENTOS CON JUNTAS INCORPORADAS
SEALED BEARINGS
Buena parte de los rodamientos ISB® rígidos de bolas de acero inoxidable están disponibles en dos versiones, blindada y con juntas deslizantes. Dichos tipos de rodamientos están lubricados de por vida, no necesitan ningún mantenimiento y no deben ser lavados ni calentados a temperaturas superiores a 80°C. La cantidad de grasa ocupa del 20% al 30% del espacio libre del rodamiento. La grasa en los rodamientos ISB® rígidos de bolas de acero inoxidable se podrá requerir atóxica, ya que este tipo específico de rodamiento se utiliza generalmente en aplicaciones alimenticias. Antes de efectuar el pedido verificar la disponibilidad de los rodamientos con grasa atóxica.
Most of the ISB® stainless steel deep groove radial ball bearings are available in two versions: with shields and with contact seals. These types of bearings are lubricated for life and are maintenance-free. They should not be washed or heated to temperatures beyond 80°C. The quantity of grease used fills 20% to 30% of the free space of the bearing. The grease used in ISB® stainless steel deep groove bearings may have to be the non-toxic type because this specific type of bearing is usually used in food processing applications. Please check availability of bearings with non-toxic grease before placing any orders.
RODAMIENTOS BLINDADOS
SHIELDED BEARINGS
La utilización de la sigla ZZ permite reconocer inmediatamente los rodamientos ISB® blindados de acero inoxidable. Los blindajes están compuestos de chapa de acero, su agujero crea un laberinto con la superficie cilíndrica externa del aro interno (Fig. 2).
Fig. 2
68
The shielded stainless steel bearings of ISB® are immediately recognisable by their designation suffix ZZ. The shields are made of sheet steel and their bore creates a labyrinth with the external cylindrical surface of the inner ring (Fig. 2).
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
Los rodamientos blindados se emplean en las aplicaciones en las que el aro interno gira. En el caso que gire el aro externo, se corre el riesgo, sobre todo a altas velocidades, que salga grasa del rodamiento.
Shielded bearings are used primarily in applications where the inner ring rotates. If it is the outer ring that rotates, there is the risk that grease may leak from the bearing, especially at high speeds.
RODAMIENTOS CON BLINDAJES DESLIZANTES
BEARINGS WITH CONTACT SHIELDS
El sufijo indicativo de los rodamientos con blindaje deslizante es 2RS (Fig. 3). Las juntas de los 2RS son de goma acrilonitrilobutadieno (NBR) y reforzadas con una chapa. El diámetro externo de esta junta está inserido en un ranurado del aro externo que lo retiene en posición sin deformaciones garantizando al mismo tiempo buenos resultados de durabilidad. Las temperaturas de empleo serán de -40°C a +100°C con picos, sólo por breves períodos, que llegan hasta +120°C. Velocidades, temperaturas muy elevadas u otras condiciones de trabajo difíciles pueden causar salida de grasa por las juntas.
Bearings with contact shields have designation suffix 2RS (Fig. 3). The seals of the 2RS bearings are made of NitrileButadiene-Rubber (NBR) with sheet metal reinforcement. The outside diameter of this seal sits in a recess in the outer ring that holds it in position without deforming it, providing a good seal at the same time. The operating temperatures will be from -40°C to +100°C with peaks up to +120°C for short periods only. Excessive speeds and temperatures or other harsh working conditions could cause grease to leak from the seals.
Fig. 3
DIMENSIONES
DIMENSIONS
TOLERANCIAS
TOLERANCES
JUEGO INTERNO
INTERNAL CLEARANCE
MATERIALES
MATERIALS
DESALINEACIÓN
MISALIGNMENT
Las dimensiones generales de los rodamientos ISB® rígidos de bolas de acero inoxidable respetan la norma ISO 15:1998.
Los rodamientos ISB® rígidos de bolas de acero inoxidable se fabrican con tolerancias Normales, de conformidad con la norma ISO 492:2002.
Los rodamientos ISB® rígidos de bolas de acero inoxidable se fabrican con un juego interno Normal, de conformidad con la norma ISO 5753:1991.
Las bolas y los aros de los rodamientos ISB® son de acero inoxidable AISI 440C, los blindajes y las jaulas de acero inoxidable AISI 302.
La desalineación angular admisible, es decir aquella desalineación que no genera ulteriores solicitaciones inaceptables depende de cuatro factores: t juego interno radial del rodamiento en las condiciones de servicio; t dimensiones; t forma constructiva interna; t carga y movimientos a los que está sujeto. Cada desalineación que se verifica causa pérdida de silenciosidad y reducción de la vida del rodamiento. No es posible
The overall dimensions of ISB® stainless steel deep groove radial ball bearings comply with standard ISO 15:1998.
ISB® stainless steel deep groove radial ball bearings are manufactured pursuant to Normal tolerances. The tolerance values comply with standard ISO 492:2002.
ISB® stainless steel deep groove radial ball bearings are manufactured with Normal internal radial clearance, pursuant to standard ISO 5753:1991.
The balls and the rings of ISB® bearings are made of stainless steel AISI 440C, the shields and the cages are made of stainless steel AISI 302.
The admitted angular misalignment, being a misalignment that does not produce unacceptable additional strain, depends on four factors: t The internal radial clearance of the bearing in the operating conditions. t The size of the bearing. t The internal constructional design. t The loads and the movements acting on the bearing. Misalignment will result in increased noise of the bearing and will reduce its life span. It is impossible to draft a table with 69
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
hacer una tabla con valores específicos de referencia porque las relaciones entre los citados factores son muy complejas.
specific reference values because the relationships between these four factors just mentioned are too complex.
JAULAS
CAGES
Los rodamientos ISB® de bolas de acero inoxidable cuentan con una de las siguientes jaulas de acero inoxidable: t Jaula estampada de acero inoxidable del tipo a presión, centrada en las bolas, ningún sufijo en el nombre (Fig. 4a); t Jaula obtenida a partir de cinta de acero inoxidable centrada en las bolas, ningún sufijo en el nombre (Fig. 4b); t Jaula estampada de acero inoxidable remachada, centrada en las bolas, ningún sufijo en el nombre (Fig. 4c);
Fig. 4a
Fig. 4b
Fig. 4c
CARGA MÍNIMA
MINIMUM LOAD
La carga mínima es de vital importancia para garantizar un funcionamiento correcto. Cualquier tipo de rodamiento deben estar sujeto a una cierta carga mínima. En los casos en que exista rotación a altas velocidades, aceleraciones elevadas o repentinos cambios de dirección, las fuerzas de inercia de las bolas y de las jaulas, la fricción del lubricante, influyen negativamente sobre las condiciones del sistema rodamiento, provocando deslizamientos perjudiciales entre las bolas y los caminos de rodadura.
The minimum load is of vital importance guarantee efficient operation. All rolling bearings must be subjected to a certain minimum load. If they are to operate at high rotation speeds, high accelerations or sudden changes in direction, the inertia forces of the balls and of the cages and the friction of the lubricant have a detrimental effect on the conditions of the bearing arrangement and may cause harmful contact between the balls and the raceways.
CAPACIDAD CARGA AXIAL
AXIAL LOAD CARRYING CAPACITY
Si los rodamientos ISB® rígidos de bolas de acero inoxidable se someten a una carga axial, esta no debe superar un valor de C0 0.25. Cargas superiores pueden causar reducción de la vida del rodamiento.
70
Stainless steel ISB® bearings (Fig. 4) are fitted with one of the following stainless steel cages: t Pressed snap-type stainless steel cage, centred on the balls, without any designation suffix (Fig. 4a). t Pressed ribbon-type sheet stainless steel cage, centred on the balls, without any designation suffix (Fig. 4b); t Pressed riveted stainless steel cage, centred on the balls, without any designation suffix (Fig. 4c);
If ISB® stainless steel deep groove radial ball bearings are subjected to an axial load, the latter must not exceed a C0 value of 0.25. Higher loads may reduce the bearing life span.
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
1
D (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
3
1
Dinámico Dynamic C 0.055
Estático Static C0 0.017
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Grease
Aceite Oil
114750
135000
Peso (Kg) Weight (Kg)
0.000036
Sigla Designation
SS 618/1
2
5
1.5
0.153
0.047
91800
108000
0.00015
SS 618/2
3
6 10
3 4
0.212 0.382
0.083 0.126
76500 61200
90000 72000
0.00035 0.0016
SS 637/3 SS 623
4
9 11 12 13
2.5 4 4 5
0.440 0.593 0.662 0.777
0.170 0.220 0.265 0.274
65025 61200 57375 51255
76500 72000 67500 60300
0.0007 0.0019 0.0024 0.0031
SS 618/4 SS 619/4 SS 604 SS 624
5
11 13 16 19
3 4 5 6
0.529 0.726 0.905 1.823
0.240 0.319 0.358 0.897
57375 51255 45900 38250
67500 60300 54000 45000
0.0012 0.0023 0.005 0.009
SS 618/5 SS 619/5 SS 625 SS 635
6
13 15 19
3.5 5 6
0.726 1.019 1.823
0.328 0.446 0.897
51255 48195 38250
60300 56700 45000
0.002 0.0039 0.0084
SS 618/6 SS 619/6 SS 626
7
14 17 19 22
3.5 5 6 7
0.790 1.215 1.823 2.705
0.382 0.529 0.897 1.294
48195 42840 40545 34425
56700 50400 47700 40500
0.0022 0.0049 0.0075 0.013
SS 618/7 SS 619/7 SS 607 SS 627
8
16 19 22
4 6 7
1.098 1.558 2.705
0.539 0.696 1.294
42840 38250 36720
50400 45000 43200
0.003 0.0071 0.012
SS 618/8 SS 619/8 SS 608
9
17 20 24 26
4 6 7 8
1.166 1.705 3.058 3.822
0.608 0.813 1.568 1.862
40545 36720 32895 29070
47700 43200 38700 34200
0.0034 0.0076 0.014 0.02
SS 618/9 SS 619/9 SS 609 SS 629
10
15 19 22 26 30 35
3 5 6 8 9 11
0.701 1.117 1.705 3.822 4.145 6.625
0.417 0.559 0.799 1.862 2.234 3.185
42840 36720 34425 30600 26010 24480
50400 43200 40500 36000 30600 28800
0.0014 0.0055 0.01 0.019 0.032 0.053
SS 61700 SS 61800 SS 61900 SS 6000 SS 6200 SS 6300
12
21 24 28 32 37
5 6 8 10 12
1.186 1.862 4.145 5.733 8.026
0.627 0.931 2.234 2.940 3.969
32895 30600 29070 24480 21420
38700 36000 34200 28800 25200
0.0063 0.011 0.022 0.037 0.06
SS 61801 SS 61901 SS 6001 SS 6201 SS 6301
15
24 28 32 35 42
5 7 9 11 13
1.274 3.567 4.586 6.370 9.369
0.764 2.117 2.695 3.577 5.096
29070 26010 24480 21420 18360
34200 30600 28800 25200 21600
0.0074 0.016 0.03 0.045 0.085
SS 61802 SS 61902 SS 6002 SS 6202 SS 6302
* Bajo demanda se suministran diversas tipologías de diseños y medidas * Available under request another stainless steel bearings solution
71
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
72
D (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Grease
Aceite Oil
Peso (Kg) Weight (Kg)
Sigla Designation
17
26 30 35 40 47
5 7 10 12 14
2.75 3.822 4.969 7.899 11.172
1.69 2.401 3.087 4.557 6.174
21420 21420 21420 18360 16830
25200 25200 25200 21600 19800
0.008 0.018 0.039 0.065 0.12
SS 61803 SS 61903 SS 6003 SS 6203 SS 6303
20
32 37 42 47 52
7 9 12 14 15
3.312 6.27 7.771 10.584 13.230
2.195 3.63 4.802 6.272 7.497
20160 16560 17280 14400 13680
25200 20700 21600 18000 17100
0.018 0.036 0.069 0.11 0.14
SS 61804 SS 61904 SS 6004 SS 6204 SS 6304
25
37 42 47 52 62
7 9 12 15 17
4.21 5.802 8.350 11.662 16.856
2.89 4.067 5.586 7.497 10.584
15120 15840 14400 12960 11520
18900 19800 18000 16200 14400
0.022 0.045 0.08 0.13 0.23
SS 61805 SS 61905 SS 6005 SS 6205 SS 6305
30
42 47 55 62 72
7 9 13 16 19
4.61 7.11 10.878 15.974 22.050
3.58 4.9 7.840 10.584 14.308
12960 12240 12240 10800 9360
16200 15300 15300 13500 11700
0.026 0.048 0.12 0.2 0.35
SS 61806 SS 61906 SS 6006 SS 6206 SS 6306
35
47 55 62 72 80
7 10 14 17 21
4.8 10.98 13.230 21.168 32.83
3.97 7.31 9.800 14.308 18.72
11520 10800 10800 9360 7200
14400 13500 13500 11700 9000
0.029 0.74 0.16 0.29 0.457
SS 61807 SS 61907 SS 6007 SS 6207 SS 6307
40
52 62 68 80 90
7 12 15 18 23
5 14.31 13.720 24.206 39.69
4.31 10 10.584 16.954 23.52
10080 9360 10080 7920 6624
12600 11700 12600 9900 8280
0.033 0.11 0.19 0.37 0.63
SS 61808 SS 61908 SS 6008 SS 6208 SS 6308
45
58 68 75 85 100
7 12 16 19 25
6.27 15.1 17.444 27.048 53
5.54 11.2 14.308 19.208 32
8640 8640 8640 7920 5904
10800 10800 10800 9900 7380
0.04 0.128 0.25 0.41 0.814
SS 61809 SS 61909 SS 6009 SS 6209 SS 6309
50
65 72 80 90 100
7 12 16 20 25
6.47 15.29 17.836 29.008 60.76
5.98 11.96 15.680 21.952 37.73
7920 7920 7920 7200 5400
9900 9900 9900 9000 6750
0.052 0.132 0.26 0.46 1.07
SS 61810 SS 61910 SS 6010 SS 6210 SS 6310
* Bajo demanda se suministran diversas tipologías de diseños y medidas * Available under request another stainless steel bearings solution
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
D (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Grease
Aceite Oil
Peso (Kg) Weight (Kg)
Sigla Designation
55
72 80 90 100 120
9 13 18 21 29
8.624 15.68 27.734 42.63 70.07
7.938 13.034 20.776 28.616 44.1
7200 6912 6480 5472 4896
9000 8640 8100 6840 6120
0.083 0.18 0.388 0.601 1.37
SS 61811 SS 61911 SS 6011 SS 6211 SS 6311
60
78 85 95 110
10 13 18 22
11.27 16.072 28.91 51.45
10.388 14.014 22.736 35.28
6768 6408 5976 5040
8460 8010 7470 6300
0.106 0.193 0.414 0.783
SS 61812 SS 61912 SS 6012 SS 6212
65
85 90 100 120
10 13 18 23
11.368 17.052 29.89 56.35
10.78 15.778 24.696 39.2
6264 5904 5544 4680
7830 7380 6930 5850
0.128 0.206 0.421 0.99
SS 61813 SS 61913 SS 6013 SS 6213
70
90 100 110
10 16 20
11.858 23.226 37.24
11.662 20.776 30.38
5832 5544 5112
7290 6930 6390
0.137 0.334 0.604
SS 61814 SS 61914 SS 6014
75
95 105
10 16
12.25 23.912
12.642 22.148
5472 5184
6840 6480
0.145 0.353
SS 61815 SS 61915
80
100 110
10 16
12.446 24.402
13.034 23.52
5112 4824
6390 6030
0.154 0.373
SS 61816 SS 61916
* Bajo demanda se suministran diversas tipologías de diseños y medidas * Available under request another stainless steel bearings solution
73
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE BLINDADOS SEALED RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm) d (mm)
74
D (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Sigla Designation
1.5
4
2
0.112
0.033
104500
0.00014
SS 638/1.5-ZZ
2
5 6 6
2.3 2.3 3
0.153 0.233 0.233
0.047 0.074 0.074
90250 85500 85500
0.00018 0.00035 0.00035
SS 638/2-ZZ SS 619/2-ZZ SS 639/2-ZZ
3
6 7 8 8 10
3 3 3 4 4
0.212 0.212 0.382 0.382 0.382
0.083 0.083 0.126 0.126 0.126
76000 76000 71250 71250 59850
0.00035 0.00045 0.00067 0.0008 0.0015
SS 637/3-ZZ SS 638/3-ZZ SS 619/3-ZZ SS 639/3-ZZ SS 623-ZZ
4
9 9 11 12 13 13 16
3.5 4 4 4 5 5 5
0.440 0.440 0.593 0.662 0.777 0.777 0.905
0.170 0.170 0.220 0.265 0.274 0.274 0.358
66500 66500 59850 57000 50350 30400 45600
0.001 0.001 0.0017 0.0023 0.0031 0.0031 0.0054
SS 628/4-ZZ SS 638/4-ZZ SS 619/4-ZZ SS 604-ZZ SS 624-ZZ SS 624-2RS SS 634-ZZ
5
8 11 11 13 16 16 19
2.5 4 5 4 5 5 6
0.137 0.529 0.529 0.726 0.905 0.905 1.823
0.056 0.240 0.240 0.319 0.358 0.358 0.897
66500 57000 57000 50350 45600 26600 38000
0.00034 0.00062 0.0019 0.0025 0.005 0.005 0.009
SS 627/5-ZZ SS 628/5-ZZ SS 638/5-ZZ SS 619/5-ZZ SS 625-ZZ SS 625-2RS SS 635-ZZ
6
10 13 15 19 19
3 5 5 6 6
0.313 0.726 1.019 1.823 1.823
0.134 0.328 0.446 0.897 0.897
57000 50350 47500 38000 22800
0.0007 0.0027 0.0037 0.0087 0.0087
SS 627/6-ZZ SS 628/6-ZZ SS 619/6-ZZ SS 626-ZZ SS 626-2RS
7
11 14 17 19 19 22
3 5 5 6 6 7
0.285 0.790 1.215 1.823 1.823 2.705
0.124 0.382 0.529 0.897 0.897 1.294
53200 47500 42750 40850 22800 34200
0.0007 0.003 0.005 0.0082 0.0082 0.013
SS 627/7-ZZ SS 628/7-ZZ SS 619/7-ZZ SS 607-ZZ SS 607-2RS SS 627-ZZ
8
16 16 19 22 22
5 6 6 7 7
1.098 1.098 1.558 2.705 2.705
0.539 0.539 0.696 1.294 1.294
42750 42750 38000 36100 20900
0.004 0.0043 0.0076 0.013 0.013
SS 628/8-ZZ SS 638/8-ZZ SS 619/8-ZZ SS 608-ZZ SS 608-2RS
9
17 20 24 26
5 6 7 8
1.166 1.705 3.058 3.822
0.608 0.813 1.568 1.862
40850 36100 32300 28500
0.0044 0.0085 0.016 0.022
SS 628/9-ZZ SS 619/9-ZZ SS 609-ZZ SS 629-ZZ
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE BLINDADOS SEALED RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Sigla Designation
d (mm)
D (mm)
10
19 19 19 22 26 26 30 30 35 35
5 5 7 6 8 8 9 9 11 11
1.117 1.117 1.117 1.705 3.822 3.822 4.145 4.145 6.625 6.625
0.559 0.559 0.559 0.799 1.862 1.862 2.24 2.24 3.19 3.19
36100 20900 36100 34200 32300 18050 26600 16150 24700 14250
0.0056 0.0056 0.0074 0.01 0.019 0.019 0.032 0.032 0.053 0.053
SS 61800-ZZ SS 61800-2RS SS 63800-ZZ SS 61900-ZZ SS 6000-ZZ SS 6000-2RS SS 6200-ZZ SS 6200-2RS SS 6300-ZZ SS 6300-2RS
12
21 24 28 28 32 32 37 37
5 6 8 8 10 10 12 12
1.19 1.87 4.15 4.15 5.74 5.74 8.03 8.03
0.63 0.94 2.24 2.25 2.94 2.94 3.969 3.969
34200 30400 28500 16150 14250 24700 20900 13300
0.0065 0.012 0.022 0.022 0.037 0.037 0.06 0.06
SS 61801-ZZ SS 61901-ZZ SS 6001-ZZ SS 6001-2RS SS 6201-2RS SS 6201-ZZ SS 6301-ZZ SS 6301-2RS
15
24 28 28 32 32 35 35 42 42
5 7 7 9 9 11 11 13 13
1.23 3.57 4.38 4.59 5.86 6.38 6.38 9.37 9.37
0.78 2.12 2.26 2.70 2.86 3.58 3.58 5.10 5.10
28500 26600 24700 20900 12350 18050 11400
0.0076 0.019 0.019 0.03 0.03 0.045 0.045 0.082 0.082
SS 61802-ZZ SS 61902-ZZ SS 61902-2RS SS 6002-ZZ SS 6002-2RS SS 6202-ZZ SS 6202-2RS SS 6302-ZZ SS 6302-2RS
17
26 26 30 35 40 47 30 35 40 47
5 5 7 10 12 14 7 10 12 14
2.75 2.75 3.83 4.97 7.9 11.18 3.83 4.97 7.9 11.18
1.69 1.69 2.401 3.11 4.56 6.18 2.41 3.1 4.6 6.2
32300 32300 30400 20900 18050 16150 13300 12350 11400 10450
0.0082 0.0082 0.019 0.039 0.065 0.12 0.019 0.039 0.065 0.12
SS 61803-ZZ SS 61803-2RS SS 61903-ZZ SS 6003-ZZ SS 6203-ZZ SS 6303-ZZ SS 61903-2RS SS 6003-2RS SS 6203-2RS SS 6303-2RS
20
32 37 37 42 42 47 47 52 52
7 9 9 12 12 14 14 15 15
3.32 5.29 5.29 7.8 7.8 10.6 10.6 13.3 13.3
2.2 3.5 3.5 4.9 4.9 6.3 6.3 7.5 7.5
12350 11400 11400 18050 10450 16150 9500 14250 9025
0.018 0.04 0.04 0.069 0.069 0.11 0.11 0.14 0.14
SS 61804-2RS SS 61904-ZZ SS 61904-2RS SS 6004-ZZ SS 6004-2RS SS 6204-ZZ SS 6204-2RS SS 6304-ZZ SS 6304-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
75
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE BLINDADOS SEALED RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm)
76
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Sigla Designation
d (mm)
D (mm)
25
37 37 42 47 47 52 52 62 62
7 7 9 12 12 15 15 17 17
4.6 4.6 5.9 8.4 8.4 11.7 11.7 16.9 16.9
3.58 3.58 4.1 5.6 5.6 7.5 7.5 10.6 10.6
10500 10500 9500 15200 9025 13300 8075 12350 7125
0.022 0.022 0.047 0.08 0.08 0.13 0.13 0.23 0.23
SS61805-ZZ SS61805-2RS SS 61905-2RS SS 6005-ZZ SS 6005-2RS SS 6205-ZZ SS 6205-2RS SS 6305-ZZ SS 6305-2RS
30
42 42 47 47 55 55 62 62 72 72
7 7 9 9 13 13 16 16 19 19
4.61 4.61 7.11 7.11 10.9 10.9 16 16 22.1 22.1
3.58 3.58 4.9 4.9 7.9 7.9 10.6 10.6 14.4 14.4
12960 12960 12240 12240 13300 7600 11400 7125 10450 5985
0.026 0.026 0.048 0.048 0.12 0.12 0.2 0.2 0.35 0.35
SS 61806-ZZ SS 61806-2RS SS 61906-ZZ SS 61906-2RS SS 6006-ZZ SS 6006-2RS SS 6206-ZZ SS 6206-2RS SS 6306-ZZ SS 6306-2RS
35
47 47 55 55 62 62 72 72 80 80
7 7 10 10 14 14 17 17 21 21
4.8 4.8 10.98 10.98 13.3 13.3 21.2 21.2 32.83 32.83
3.97 3.97 7.31 7.31 9.9 9.9 14.4 14.4 18.72 18.72
11520 11520 10800 10800 11400 6650 9500 5985 7200 7200
0.029 0.029 0.74 0.74 0.16 0.16 0.29 0.29 0.457 0.457
SS 61807-ZZ SS 61807-2RS SS 61907-ZZ SS 61907-2RS SS 6007-ZZ SS 6007-2RS SS 6207-ZZ SS 6207-2RS SS 6307-ZZ SS 6307-2RS
40
52 52 62 62 68 68 80 80 90 90
7 7 12 12 15 15 18 18 23 23
5 5 14.31 14.31 13.8 13.8 24.3 24.2 39.69 39.69
4.31 4.31 10 10 10.6 10.6 17 17 23.52 23.52
10080 10080 9360 9360 10450 5985 8550 5320 6624 6624
0.033 0.033 0.11 0.11 0.19 0.19 0.37 0.37 0.63 0.63
SS 61808-ZZ SS 61808-2RS SS 61908-ZZ SS 61908-2RS SS 6008-ZZ SS 6008-2RS SS 6208-ZZ SS 6208-2RS SS 6308-ZZ SS 6308-2RS
45
58 58 68 68 75 75 85 85
7 7 12 12 16 16 19 19
6.27 6.27 15.1 15.1 17.5 17.5 27.1 27.1
5.54 5.54 11.2 11.2 14.4 14.4 19.3 19.3
8640 8640 8640 8640 9500 5320 8075 4750
0.04 0.04 0.128 0.128 0.25 0.25 0.41 0.41
SS 61809-ZZ SS 61809-2RS SS 61909-ZZ SS 61909-2RS SS 6009-ZZ SS 6009-2RS SS 6209-ZZ SS 6209-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE BLINDADOS SEALED RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm)
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Sigla Designation
d (mm)
D (mm)
45
100 100
25 25
53 53
32 32
5904 5904
0.814 0.814
SS 6309-ZZ SS 6309-2RS
50
65 65 72 72 80 80 90 90 100 100
7 7 12 12 16 16 20 20 25 25
6.47 6.47 15.29 15.29 17.9 17.9 29.1 29.1 60.76 60.76
5.98 5.98 11.96 11.96 15.7 15.7 22 22 37.73 37.73
7920 7920 7920 7920 8550 4750 7600 4560 5400 5400
0.052 0.052 0.132 0.132 0.26 0.26 0.46 0.46 1.07 1.07
SS 61810-ZZ SS 61810-2RS SS 61910-ZZ SS 61910-2RS SS 6010-ZZ SS 6010-2RS SS 6210-ZZ SS 6210-2RS SS 6310-ZZ SS 6310-2RS
55
72 72 80 80 90 90 100 100 120 120
9 9 13 13 18 18 21 21 29 29
8.624 8.624 15.68 15.68 27.734 27.734 42.63 42.63 70.07 70.07
7.938 7.938 13.034 13.034 20.776 20.776 28.616 28.616 44.1 44.1
7200 7200 6912 6912 6480 6480 5472 5472 4896 4896
0.083 0.083 0.18 0.18 0.388 0.388 0.601 0.601 1.37 1.37
SS 61811-ZZ SS 61811-2RS SS 61911-ZZ SS 61911-2RS SS 6011-ZZ SS 6011-2RS SS 6211-ZZ SS 6211-2RS SS 6311-ZZ SS 6311-2RS
60
78 78 85 85 95 95 110 110
10 10 13 13 18 18 22 22
11.27 11.27 16.072 16.072 28.91 28.91 51.45 51.45
10.388 10.388 14.014 14.014 22.736 22.736 35.28 35.28
6768 6768 6408 6408 5976 5976 5040 5040
0.106 0.106 0.193 0.193 0.414 0.414 0.783 0.783
SS 61812-ZZ SS 61812-2RS SS 61912-ZZ SS 61912-2RS SS 6012-ZZ SS 6012-2RS SS 6212-ZZ SS 6212-2RS
65
85 85 90 90 100 100 120 120
10 10 13 13 18 18 23 23
11.368 11.368 17.052 17.052 29.89 29.89 56.35 56.35
10.78 10.78 15.778 15.778 24.696 24.696 39.2 39.2
6264 6264 5904 5904 5544 5544 4680 4680
0.128 0.128 0.206 0.206 0.421 0.421 0.99 0.99
SS 61813-ZZ SS 61813-2RS SS 61913-ZZ SS 61913-2RS SS 6013-ZZ SS 6013-2RS SS 6213-ZZ SS 6213-2RS
70
90 90 100 100 110 110
10 10 16 16 20 20
11.858 11.858 23.226 23.226 37.24 37.24
11.662 11.662 20.776 20.776 30.38 30.38
5832 5832 5544 5544 5112 5112
0.137 0.137 0.334 0.334 0.604 0.604
SS 61814-ZZ SS 61814-2RS SS 61914-ZZ SS 61914-2RS SS 6014-ZZ SS 6014-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
77
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS DE ACERO INOXIDABLE BLINDADOS SEALED RADIAL STAINLESS STEEL DEEP GROOVE BALL BEARINGS
Dimensiones (mm) Dimension (mm)
78
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad limite* Speed limit*
Peso (Kg) Weight (Kg)
Sigla Designation
d (mm)
D (mm)
75
95 95 105 105
10 10 16 16
12.25 12.25 23.912 23.912
12.642 12.642 22.148 22.148
5472 5472 5184 5184
0.145 0.145 0.353 0.353
SS 61815-ZZ SS 61815-2RS SS 61915-ZZ SS 61915-2RS
80
100 100 110 110
10 10 16 16
12.446 12.446 24.402 24.402
13.034 13.034 23.52 23.52
5112 5112 4824 4824
0.154 0.154 0.373 0.373
SS 61816-ZZ SS 61816-2RS SS 61916-ZZ SS 61916-2RS
* Para los rodamientos blindados sólo de un lado son válidas las velocidades límite de los rodamientos abiertos * For one side shield bearings speed limit, use the same value of open bearings
Rodamientos rígidos de dos hileras de bolas Radial deep groove ball bearings, double rows
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE DOS HILERAS DE BOLAS
DOUBLE ROW DEEP GROOVE RADIAL BALL BEARINGS
Los rodamientos ISB® rígidos de dos hileras de bolas (Fig. 1) logran resistir cargas axiales en los dos sentidos sumadas a las cargas radiales, ya que cuentan con ranuras profundas y con un elevado grado de contacto entre las bolas y los caminos de rodadura. Este tipo de rodamiento está indicado para aplicaciones en las cuales la capacidad de carga de los rodamientos de una bola no es suficiente; en efecto con el mismo diámetro externo y con el mismo agujero, los rodamientos de dos hileras de bolas soportan cargas muy superiores respecto a los de una sola hilera de bolas
(Fig. 1) Due to the fact that the double row deep groove radial ball bearings produced by ISB® have deep grooves and very close conformity between balls and raceways, they are able to withstand axial loads in both directions in addition to radial loads. This type of bearing is suitable for applications in which the load carrying capacity of single row bearings is inadequate; with the same outside diameter and bore, double row ball bearings do indeed withstand much higher loads than single row bearings.
Fig. 1
DIMENSIONES
DIMENSIONS
Las dimensiones generales de los rodamientos ISB® rígidos de dos hileras de bolas respetan la norma ISO 15:1998.
The overall dimensions of ISB® double row deep groove radial ball bearings comply with standard ISO 15:1998.
TOLERANCIA
TOLERANCE
Los rodamientos ISB® rígidos de dos hileras de bolas se fabrican según las tolerancias normales.
ISB® double row deep groove radial ball bearings are manufactured pursuant to Normal tolerances.
JUEGO INTERNO
INTERNAL CLEARANCE
Los rodamientos ISB® rígidos de dos hileras de bolas se fabrican con un juego interno Normal, de conformidad con la norma 57-53:1991.
ISB® double row deep groove radial ball bearings are manufactured with Normal internal radial clearance, pursuant to standard ISO 57-53:1991.
DESALINEACIÓN
MISALIGNMENT
Cada desalineación de los aros del rodamiento causa una disminución de silenciosidad.
Misalignment in the rings of the bearing will result in higher noise of the bearing.
JAULAS
CAGES
Los rodamientos ISB® rígidos de dos hileras de bolas prevén dos jaulas moldeadas por inyección, a presión, en poliamida 6.6 reforzada en fibra de vidrio y centradas en las bolas (Fig. 2) sufijo TN9 en la sigla. Este tipo de rodamiento puede utilizarse a temperaturas que alcanza los +120ºC, los lubricantes utilizados generalmente no dañan las jaulas.
Fig. 2
80
ISB® double row deep groove radial ball bearings are fitted with two injection moulded snap-type cages of polyamide 6.6 with fibreglass reinforcement and centred on the balls (Fig. 2), with designation suffix TN9. This type of bearing can be used at temperatures up to +120°C. The lubricants used do not usually have a detrimental effect on the cages.
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
CARGA MÍNIMA
MINIMUM LOAD
CAPACIDAD DE CARGA AXIAL
AXIAL LOAD CARRYING CAPACITY
Necesaria para garantizar un funcionamiento correcto. Todos los rodamientos deben estar sujetos a una cierta carga mínima. En los casos en que exista rotación a altas velocidades, aceleraciones elevadas o repentinos cambios de dirección, las fuerzas de inercia de las bolas y de las jaulas, la fricción del lubricante, influyen negativamente sobre las condiciones del sistema rodamiento, provocando deslizamientos perjudiciales entre las bolas y los caminos de rodadura.
Si los rodamientos ISB® rígidos de bolas de acero se someten a una carga axial, ésta no debe superar un valor de 0.5 C0. Cargas superiores pueden causar reducción de la vida del rodamiento.
This is required to guarantee efficient operation. All rolling bearings must be subjected to a certain minimum load. If they are to operate at high rotation speeds, high accelerations or sudden changes in direction, the inertia forces of the balls and of the cages and the friction of the lubricant have a detrimental effect on the conditions of the bearing arrangement and may cause harmful contact between the balls and the raceways.
If ISB® deep groove steel ball bearings are subjected to an axial load, the latter must not exceed a value of 0.5 C0. Greater loads may reduce the bearing life span.
81
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE DOS HILERAS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS - DOUBLE ROW
Dimensiones (mm) Dimension (mm)
82
Coeficiente de carga (KN) Load rating (KN)
B (mm)
Dinámico Dynamic C
Estático Static C0
Velocidad límite (rpm) Speed limit (Rpm) Lubrificación Lubrication Grasa Aceite Grease Oil
Peso (Kg) Weight (Kg)
Sigla Designation
d (mm)
D (mm)
10
30
14
9.05
5.10
16830
19800
0.049
4200 ATN9
12
32 37
14 17
10.39 12.74
6.08 7.64
15300 13770
18000 16200
0.053 0.092
4201 ATN9 4301 ATN9
15
35 42
14 17
11.66 14.50
7.35 9.31
13005 11475
15300 13500
0.059 0.12
4202 ATN9 4302 ATN9
17
40 47
16 19
14.50 19.11
9.31 12.94
11475 9945
13500 11700
0.09 0.16
4203 ATN9 4303 ATN9
20
47 52
18 21
17.44 22.93
12.25 15.68
9945 9180
11700 10800
0.14 0.21
4204 ATN9 4304 ATN9
25
52 62
18 24
18.62 31.26
14.31 21.95
8415 7650
9900 9000
0.16 0.34
4205 ATN9 4305 ATN9
30
62 72
20 27
25.48 40.18
20.38 29.40
7268 6503
8550 7650
0.26 0.5
4206 ATN9 4306 ATN9
35
72 80
23 31
34.40 49.69
27.93 37.24
6120 5738
7200 6750
0.4 0.69
4207 ATN9 4307 ATN9
40
80 90
23 33
36.36 54.78
31.85 44.10
5355 5126
6300 6030
0.5 0.95
4208 ATN9 4308 ATN9
45
85 100
23 36
38.22 67.52
35.28 54.88
5126 4590
6030 5400
0.54 1.25
4209 ATN9 4309 ATN9
50
90 110
23 40
40.18 80.26
39.20 68.11
4590 4055
5400 4770
0.58 1.7
4210 ATN9 4310 ATN9
55
100 120
25 43
44.00 95.55
43.12 81.34
4284 3825
5040 4500
0.8 2.15
4211 ATN9 4311 ATN9
60
110 130
28 46
56.06 109.76
53.90 96.04
4055 3443
4770 4050
1.1 2.65
4212 ATN9 4312 ATN9
65
120 140
31 48
66.25 118.58
65.66 103.88
3672 3290
4320 3870
1.45 3.25
4213 ATN9 4313 ATN9
70
125 150
31 51
68.80 135.24
72.03 122.50
3290 2907
3870 3420
1.5 3.95
4214 ATN9 4314 ATN9
75
130 160
31 55
71.34 152.88
78.40 140.14
3060 2754
3600 3240
1.6 4.8
4215 ATN9 4315 ATN9
80
140
33
78.99
88.20
2907
3420
2
4216 ATN9
85
150
36
91.73
99.96
2754
3240
2.55
4217 ATN9
90
160
40
109.76
119.56
2601
3060
3.2
4218 ATN9
100
180
46
137.20
152.88
2295
2700
4.7
4220 ATN9
Rodamientos rígidos de bolas Radial deep groove ball bearings
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS RÍGIDOS DE UNA HILERA DE BOLAS
SINGLE ROW DEEP GROOVE RADIAL BALL BEARINGS
ISB® produce diversos tipos de rodamientos rígidos de una hilera de bolas, identificados por especificas características técnicas y peculiares aplicaciones mecánicas. En virtud de las amplias posibilidades propuestas al comprador, los rodamientos rígidos de una hilera de bolas se pueden subdividir en tres grupos: t Rodamientos estándar t Rodamientos con juntas t Rodamientos ranurados para el aro de fijación (con o sin aro de fijación). Los rodamientos rígidos de una hilera de bolas, siendo estructuralmente simples y no desmontables, no presentan exigencias específicas de mantenimiento, además, se presentan resistentes y particularmente idóneos para prestaciones de velocidad elevada, resultando por este motivo fiables y versátiles en sus posibles aplicaciones mecánicas. Los rodamientos rígidos de una hilera de bolas producidos por ISB®, contando con ranuras profundas y un elevado contacto, es decir un elevado coeficiente entre el radio del camino de rodadura y el diámetro de las bolas, pueden resistir, además de cargas radiales, requerimientos axiales en ambos sentidos. En caso de aplicaciones especiales de rodamientos rígidos de una hilera, contactar con el servicio técnico ISB®. Para informaciones inherentes a rodamientos, en lo relativo a las dimensiones o características morfológicas, contactar con la oficina técnica ISB®.
ISB® produces various types of single row deep groove radial ball bearings, which differ in terms of specific technical characteristics and of peculiar mechanical applications. In view of the assortment offered to purchasers, the single row deep groove radial ball bearings can be split-up into three groups: t Standard bearings t Sealed bearings t Bearings with snap ring grooves (with or without snap ring).
RODAMIENTOS ESTÁNDAR
STANDARD BEARING
Los rodamientos base ISB® (Fig. 1) son abiertos, sin juntas.
Seeing as the single row deep groove radial ball bearings are structurally simple and not separable, they do not involve any maintenance requirements in particular. They are resistant and particularly suited for high speed outputs and are consequently reliable and versatile in their possible mechanical applications. Due to the fact that the single row deep groove radial ball bearings produced by ISB® have deep grooves and very close conformity, or rather a high ratio between the radius of the raceway and the diameter of the balls, they are able not only to withstand radial loads but also axial loads in both directions. For special applications of the single row deep groove radial ball bearings, please contact the engineering department of ISB®. For information concerning the bearings with regard to sizes or morphologic specifications, please contact the application engineering department of ISB®.
The standard bearings of ISB® (Fig. 1) are open i.e. unsealed.
Fig. 1
RODAMIENTOS CON JUNTAS INCLUIDAS
Las dimensiones más usuales se fabrican también para los rodamientos con juntas incluidas. Dicho tipo de rodamiento está lubricado de por vida y no necesita mantenimiento. El tipo de grasa lubricante varía según la dimension, su grado de llenado es del 20/30% del espacio libre en el rodamiento. Para garantizar su correcto funcionamiento, los rodamientos no deben alcanzar temperaturas superiores a los 80º y no deben ser lavados. La realización de los rodamientos especiales, con otros grados de llenado o la utilización de grasas especiales se efectúan y suministran previa solicitud.
28
SEALED BEARINGS
The most popular sizes of bearings are also produced for sealed bearings. This type of bearing is lubricated for life and requires no future maintenance. The type of lubricant grease varies based on the sizes and the filling grade is 20/30% of the free space in the bearing. To guarantee the correct use of the bearings, they should not be heated to temperatures beyond 80 °C and should not be washed. Special bearings with other filling grades or ones with special grease can be produced and supplied on specific request.
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS BLINDADOS
Se reconocen gracias a los sufijos Z y ZZ en el nombre. Los blindajes son de chapa de acero, su orificio crea un laberinto con la superficie cilíndrica externa del aro interno (Fig. 2). Los rodamientos blindados se emplean en las aplicaciones en las que el aro interno gira. En el caso que gire el aro externo, se puede producir, sobre todo a altas velocidades, salida de grasa del rodamiento.
SHIELDED BEARINGS
Shielded bearings are identified by the designation suffix Z and ZZ. The shields are made of sheet steel and their bore creates a labyrinth with the external cylindrical surface of the inner ring (Fig. 2). Shielded bearings are used primarily in applications where the inner ring rotates. If it is the outer ring that rotates, there is the risk that grease may leak from the bearing, especially at high speeds.
Fig. 2
RODAMIENTOS CON BLINDAJES DE REDUCIDA FRICCIÓN.
Los rodamientos ISB® rígidos de bolas blindados con reducida fricción se identifican con los siguientes sufijos: RZ para rodamientos blindados de un solo lado, 2RZ para indicar aquellos con juntas en ambos lados (Fig. 3). Los blindajes son de goma acrilonitrilo-butadieno (NBR) y reforzados con una chapa. El NBR es resistente a los aceites y al desgaste. Los blindajes junto a la superficie cilíndrica externa del aro interno forman un espacio muy pequeño y son no deslizantes. Esta es la razón por la cual los rodamientos ISB® con blindajes de baja fricción tienen una durabilidad mayor y pueden trabajar a las mismas altas velocidades de los rodamientos blindados Z. Las temperaturas de utilización varían de -40°C a +100°C. Para breves períodos se puede alcanzar una temperatura máxima de +120°C.
BEARINGS WITH LOW-FRICTION SHIELDS
The deep groove radial ball bearings of ISB® with lowfriction shields are identified by the designation suffixes: RZ for ball bearings shielded just on one side, 2RZ for those with shields on both sides (Fig. 3). The shields are made of NitrileButadiene-Rubber (NBR) with sheet steel reinforcement. This rubber is resistant to oil and wear. The shields form a very small gap with the external cylindrical surface of the inner ring and do not touch each other. This is why ISB® ball bearings with low-friction shields have a better seal and can work at the same speeds as the Z type shielded ball bearings. The operating temperatures vary from -40°C to +100°C. They can even work at a maximum temperature of +120°C but for short periods only.
Fig. 3
RODAMIENTOS CON BLINDAJES DESLIZANTES
Los sufijos indicativos de los rodamientos con blindaje deslizante son RS y 2RS (Fig. 4). El diametro externo de las juntas está inserido en un ranurado de las caras del aro externo que lo retiene en posición sin deformaciones garantizando al mismo tiempo buenos resultados de durabilidad. Como hemos visto para los rodamientos con blindajes de reducida fricción, las juntas de los RS y 2RS son de goma acrilonitrilobutadieno (NBR) reforzadas con una chapa. Combinando el material de composición, las temperaturas de utilización serán las mismas, es decir de -40°C a +100°C con picos, sólo para períodos breves, que llegan hasta +120°C. Velocidades, temperaturas demasiado elevadas u otras condiciones de trabajo difíciles pueden causar perdidas de grasa de los labios.
BEARINGS WITH CONTACT SHIELDS
The ball bearings with contact shields are identified with designation suffix RS and 2RS (Fig. 4). The outside diameter of the seals sits in a recess in the outer ring that holds it in position without deforming it, providing a good seal at the same time. Likewise for the ball bearings with low-friction shields, the RS and 2RS seals are made of Nitrile-Butadiene-Rubber (NBR) with sheet steel reinforcement. Sharing the same composition material, the operating temperatures will be the same, in other words from -40°C to +100°C with peaks up to +120°C for short periods only. Excessive speeds and temperatures or other harsh working conditions could cause grease to leak from the inner rings.
29
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
Fig. 4
RODAMIENTOS CON UN RANURADO PARA ARO DE FIJACIÓN
Los rodamientos ISB® rígidos de una hilera de bolas con ranurado para aro de fijación se suministran en las siguientes versiones: t Abiertos, N es el sufijo en el nombre (Fig. 5a); t Abiertos con aro de fijación, NR es el sufijo en el nombre (Fig. 5b); t Con junta Z en el lado opuesto al ranurado y aro de fijación, ZNR es el sufijo en el nombre (Fig. 5c); t Con juntas Z en ambos lados y aro de fijación, 2ZNR es el sufijo en el nombre (Fig. 5d).
Fig. 5a
Fig. 5b
Estos tipos de rodamientos simplifican el proyecto ya que permiten la retención en sentido axial en el alojamiento mediante un aro de fijación o de retención (Fig. 6), garantizando al mismo tiempo un ahorro en términos de espacio. En la tabla de los productos se expone, ademas de los rodamientos, los nombres y las dimensiones de los aros de fijación, porque los mismos se podrán suministrar por separado o bien ya montados.
Fig. 6
30
BEARINGS WITH ONE SNAP RING GROOVE
ISB® single row deep groove radial ball bearings with one snap ring groove are supplied in the following versions: t t t t
Open, N being the designation suffix (Fig. 5a); Open with snap ring, NR being the designation suffix (Fig. 5b); With Z shield on the side opposite the groove and with snap ring, ZNR being the designation suffix (Fig. 5c); With Z shield on both sides and with snap ring, 2ZNR being the designation suffix (Fig. 5d).
Fig. 5c
Fig. 5d
These types of bearings simplify the project because they can be detained axially in the housing by a snap ring or retaining ring (Fig. 6), which also saves space. In the product table, together with the bearings, the designations and the dimensions of the snap rings are also given, because they may be supplied separately or already fitted on the bearing.
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
RODAMIENTOS DE BOLAS SELLADOS
Los rodamientos de bolas sellados (Fig.7) se basan en los rodamientos rígidos de bolas de la serie 62.
SEALED BALL BEARINGS
The sealed ball bearings (Fig.7) are based on series 62 deep groove ball bearings.
Fig. 7
Presentan una superficie de rotacion convexa y cuentan, en ambos lados, con juntas deslizantes de goma acrilonitrilobutadieno (NBR) reforzadas con chapa. Se suministran listos para el montaje y pre-engrasados. Gracias a su superficie de rotación convexa pueden ser utilizados en aplicaciones en las cuales resulte probable una desalineación angular respecto al camino de rodadura, y en aquellas donde sea necesario reducir al mínimo las solicitaciones periféricas.
They have a crowned rolling surface and have sliding shields in Nitrile-Butadiene-Rubber (NBR) with sheet steel reinforcement on both sides. They are supplied ready for assembly and pre-greased. Thanks to their crowned rolling surface they can be used in applications where there is a probable angular misalignment compared to the raceway and where peripheral strain must be minimised.
DIMENSIONES
DIMENSIONS
TOLERANCIAS
TOLERANCES
JUEGO INTERNO
INTERNAL CLEARANCE
DESALINEACIÓN
MISALIGNMENT
Las dimensiones generales de los rodamientos ISB® rígidos de una hilera de bolas respetan la norma ISO 15:1998.
Los rodamientos rígidos de una hilera de bolas ISB® se fabrican de conformidad con las tolerancias normales. Los valores de las tolerancias respetan la norma ISO 492:2002. ISB® , específicamente para los sistemas de rodamientos en los cuales la precisión resulta un factor determinante, produce algunos con grados de precisión conforme a las clases P6 o P5. Si Usted desea solicitar estos rodamientos rígidos de bolas particulares contacte con la oficina técnica.
Los valores de juego interno radial se indican en la tabla expuesta en la introducción, respetan la norma ISO 5753:1991 y se refieren a rodamientos no montados y carga de medida cero. Los rodamientos ISB® rígidos de una hilera de bolas se fabrican generalmente con juego interno radial denominado Normal. Una parte de los rodamientos se suministran con juegos radiales internos diferentes del estándar: C2 menores de la medida normal, C3, C4 y C5 mayores. Estas cuatro variantes están disponibles previa solicitud.
La desalineación angular admisible, es decir aquella desalineación que no genera ulteriores solicitaciones inaceptables depende de cuatro factores: t juego interno radial del rodamiento en las condiciones de servicio; t dimensiones; t forma constructiva interna; t cargas y movimientos a los que está sujeto.
The overall dimensions of ISB® single row deep groove radial ball bearings comply with standard ISO 15:1998.
ISB® single row deep groove radial ball bearings are manufactured pursuant to Normal tolerances. The tolerance values comply with standard ISO 492:2002. For bearing arrangements where precision is the key factor, ISB® produces some specific bearings with precision pursuant to class P6 or P5. If you wish to order these special types of deep groove radial ball bearings, please contact the application engineering department.
The internal radial clearance values are indicated in the table given in the introduction and comply with standard ISO 5753:1991: They refer to unfitted bearings with zero measuring load. ISB® single row deep groove radial ball bearings are usually manufactured with Normal internal radial clearance. Some of the bearings are supplied with non-standard internal radial clearances: C2 smaller than normal clearance, C3, C4 and C5 greater. These four variants are supplied on specific request.
The admitted angular misalignment, being a misalignment that does not produce unacceptable additional strain, depends on four factors: t The internal radial clearance of the bearing in the operating conditions. t The size of the bearing. t The internal constructional design. t The loads and the movements acting on the bearing. 31
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
Cada desalineación produce pérdida de silenciosidad y reducción de la vida del rodamiento; no es posible hacer una tabla con valores específicos de referencia porque las relaciones que interesan los citados factores son muy complejas.
Misalignment will result in increased noise of the bearing and will reduce its life span. It is impossible to draft a table with the specific reference values because the relationships between these four factors just mentioned are too complex.
JAULAS
CAGES
Los rodamientos con jaulas de chapa estampada en diseño normal están disponibles también en las otras versiones con jaulas mecanizadas de latón o moldeadas por inyección, a presión de poliamida 6.6.
Standard ball bearings with pressed steel cage are also available in other versions with solid machined brass or injection moulded snap-type cages made of polyamide 6.6.
En base a las diversas dimensiones, serie y diseños son siete las jaulas con las que cuentan los rodamientos ISB® rígidos de una hilera de bolas: t obtenidas a partir de cinta, en chapa de acero, centradas en las bolas, ningún sufijo en el nombre (Fig. 8a); t obtenidas a partir de cinta, en latón, centradas en las bolas, Y es el sufijo en el nombre; t remachadas, en chapa de acero, centradas en las bolas, ningún sufijo en el nombre (Fig. 8b); t remachadas, en latón, centradas en las bolas, Y es el sufijo en el nombre; t mecanizadas de latón, centradas en las bolas, M es el sufijo en el nombre (Fig. 8c); t mecanizadas de latón, centradas en el aro externo, M es el sufijo en el nombre; t moldeadas por inyección, a presión, en poliamida 6.6 reforzada en fibra de vidrio, centradas en las bolas, TN9 es el sufijo en el nombre (Fig. 8d);
Fig. 8a
Fig. 8b
Fig. 8c
Fig. 8d
Los rodamientos TN9 pueden ser utilizados hasta temperaturas que alcanzan los +120°C .
TN9 bearings can be used for temperatures up to +120°C .
Atención al utilizar aceites sintéticos, grasa a base de aceite sintético y lubricantes con alto porcentaje de adivitos EP si se los utiliza a altas temperaturas, podrían dañar las jaulas.
Beware when using synthetic oil, synthetic oil-based grease and lubricants with high percentage of EP additives if used at high temperatures, as they could damage the cages.
CARGA MÍNIMA
MINIMUM LOAD
Necesaria para garantizar un funcionamiento correcto. Todos los rodamientos envolventes deben estar sujetos a una cierta carga mínima. En los casos en que exista rotación a altas velocidades, aceleraciones elevadas o repentinos cambios de dirección, las fuerzas de inercia de las bolas y de las jaulas, la fricción del lubricante, influyen negativamente sobre las condiciones del sistema rodamiento, provocando deslizamientos perjudiciales entre bolas y aros.
32
Based on the various sizes, series and versions, ISB® single row deep groove radial ball bearings are fitted with one of the following cages: t pressed ribbon-type steel cage, centred on the balls, without any designation suffix (Fig. 8a); t pressed ribbon-type brass cage, centred on the balls, with designation suffix Y; t riveted pressed steel cage, centred on the balls, without any designation suffix (Fig. 8b); t riveted pressed brass cage, centred on the balls, with designation suffix Y; t Solid machined brass cage, centred on the balls, with designation suffix M (Fig. 8c); t Solid machined brass cage, centred on the outer ring, with designation suffix MA; t injection moulded snap-type cage made of polyamide 6.6 with fibreglass reinforcement, centred on the balls, with designation suffix TN9 (Fig. 8d);
This is required to guarantee efficient operation. All rolling bearings must be subjected to a certain minimum load. If they are to operate at high rotation speeds, high accelerations or sudden changes in direction, the inertia forces of the balls and of the cages and the friction of the lubricant have a detrimental effect on the conditions of the bearing arrangement and may cause harmful contact between the balls and the raceways.
RODAMIENTOS RÍGIDOS DE BOLAS RADIAL DEEP GROOVE BALL BEARINGS
CAPACIDAD CARGA AXIAL
AXIAL LOAD CARRYING CAPACITY
DESIGNACIONES SUPLEMENTARIAS
SUPPLEMENTARY DESIGNATIONS
La carga axial pura no puede superar 0.5 C0. En los rodamientos de pequeñas dimensiones (diámetros hasta aprox. 12 mm) y en aquellos de las series ligeras (serie diametrales 8, 9, 0, y 1), el correspondiente límite es 0,25 C0. Cargas axiales excesivas pueden reducir notablemente la durabilidad del rodamiento.
Los sufijos utilizados para identificar algunas características de los rodamientos rígidos de bolas ISB® son los siguientes: C2 C3 C4 C5 J M MA MB N NR P5 P6 P52 P62 P63 RS
RZ
TN TN9 Y Z ZNR
2RS
2RZ
ZZ ZZNR
Juego radial interno inferior al Normal Juego radial interno mayor al Normal Juego radial interno mayor que C3 Juego radial interno mayor que C4 Jaula estampada de acero Jaula mecanizada de latón centrada en las bolas Jaula mecanizada de latón, centrada en el aro externo Jaula mecanizada de latón, centrada en el aro interno Ranurado para anillo elástico en el aro externo Ranurado para anillo elástico en el aro externo, con anillo elástico Precisión dimensional y de rotación según la clase de tolerancia 5 de la norma ISO Precisión dimensional y de rotación según la clase de tolerancia 6 de la norma ISO P5 + C2 P6 + C2 P6 + C3 Obturación de goma acrilonitrilo-butadieno (NBR) con refuerzo de chapa estampada, de un lado del rodamiento Obturación con reducida fricción de goma acrilonitrilo-butadieno (NBR) con refuerzo de chapa estampada, de un lado del rodamiento Jaula moldeada por inyección de poliamida Jaula moldeada por inyección de poliamida 6,6 reforzada con fibras de vidrio Jaula moldeada de latón Blindaje de chapa moldeada (obturación no deslizante), de un lado del rodamiento Ranurado para anillo elástico en el aro externo, con anillo elástico y blindaje de chapa del lado opuesto del ranurado Obturación de goma acrilonitrilo-butadieno (NBR) con refuerzo de chapa, en ambos lados del rodamiento Obturación con reducida fricción de goma acrilonitrilo-butadieno (NBR) con refuerzo de chapa estampada, de ambos lados del rodamiento Blindaje Z de ambos lados del rodamiento Ranurado para anillo elástico en el aro externo, con anillo elástico y blindajes de chapa estampada de ambos lados del rodamiento
The pure axial load must not exceed 0.5 C0. For small bearings (diameters up to approximately 12 mm) and light series bearings (diameter series 8, 9, 0, and 1), the corresponding limit is 0,25 C0. Excessive axial loads may considerably reduce the bearing life span.
The designation suffixes used to identify certain characteristics of ISB® deep groove radial ball bearings are the following: C2 Internal radial clearance smaller than Normal C3 Internal radial clearance greater than Normal C4 Internal radial clearance greater than C3 C5 Internal radial clearance greater than C4 J Pressed steel cage M Solid machined brass cage, centred on the balls MA Solid machined brass cage, centred on the outer ring MB Solid machined brass cage, centred on the inner ring N Groove for snap ring on outer ring NR Groove for snap ring on outer ring, with snap ring P5 P6 P52 P62 P63 RS
RZ
TN TN9 Y Z ZNR
Dimensional and rotation precision pursuant to tolerance class 5 of ISO standard Dimensional and rotation precision pursuant to tolerance class 6 of ISO standard P5 + C2 P6 + C2 P6 + C3 Nitrile-Butadiene-Rubber (NBR) sealwith pressed sheet steel reinforcement, on one side of the bearing Nitrile-Butadiene-Rubber (NBR) low friction seal with pressed sheet steel reinforcement, on one side of the bearing Injection moulded cage ofpolyamide Injection moulded cage of polyamide 6.6 with fibreglass reinforcement Pressed brass cage Pressed sheet steel shield (no contact seal) on one side of the bearing Groove for snap ring on outer ring, with snap ring and sheet steel shield opposite the groove
2RS
Nitrile-Butadiene-Rubber (NBR) seal with sheet steel reinforcement, on both sides of the bearing
2RZ
Nitrile-Butadiene-Rubber (NBR) low friction seal with pressed sheet steel reinforcement, on both sides of the bearing
ZZ ZZNR
Z shield on both sides of the bearing Groove for snap ring on outer ring with snap ring and pressed sheet steel shields on both sides of the bearing
33