Concrete Inserts

Continuous concrete inserts, installed in the ceiling, can be used to support trapeze hangers, suspended pipe racks, cable trays and single or multiple pipe hangers. When installed in walls, continuous concrete inserts can be used as a support for tunnel stanchions, equipment braces, brackets and pipe racks.

Concrete Inserts

Use spot inserts for single pipe-support or trapeze type hangers. Spot Inserts offer full flexibility of rod and fastener sizings. Our channel can be attached to continuous concrete inserts in walls or ceilings. Channel can also be attached to concrete walls and floors with expansion anchors.

Reference page 213 for general fitting and standard finish specifications. Strut Systems

214

Continuous Concrete Inserts B22I Continuous Concrete Insert

15/8” 4”

(41.3)

(101.6) • Design Load for B22-I-12 thru B22-I-240 is 2,000 lbs. (8.89 kN) per foot of concrete MATERIAL: 12 Gauge (2.6) insert length with safety factor of 3 in 11/2” 3000 psi concrete. (38.1) • Loads concentrated within the last 2 3/4” inches (50.8 mm) of concrete inserts (19.0) 1 3 /8” 8” (203.2 mm) and longer should not (79.4) exceed 1,000 lbs. (4.45kN). • Concrete insert should be secured to the .188 Knockouts For forms on 16” (406.4 mm) to 24” (609.6 mm) Nailing Inserts To 11 B22-I-3 Thru /16” intervals. Forms (17.4) B22-I-8 • B22-I continuous concrete inserts are made from B22 channel. Use channel 25/8” 15/8” Styrofoam nuts designed for use in B22 channel. 15/8” (66.7) Filler (41.3) • B22-I concrete inserts are supplied with (41.3) styrofoam fillers. B3322 end caps are furnished with inserts through 8” (203.2 mm) long, and B205 end caps are furnished with inserts 12” (304.8 mm) and longer. 15/8” • Material: Plain Steel ASTM A1011 (41.3) 33,000 PSI min. yield or Pre-Galvanized Steel ASTM A653SS 33,000 PSI min. Styrofoam B3322 yield. Filler End Cap • Finish: Plain, DURA GREEN™, Pre-Galv, B205 End Cap HDG B22-I-12 THRU B22-I-240

Concrete Inserts

Length Part No.

in.

B22-I-3 B22-I-4 B22-I-6 B22-I-8

3” 4” 6” 8”

Wt./C Lbs.

kg

Lbs.

kN

(76)

72 88 120 152

(32.6)

500 800 1000 1200

(2.22)

(101) (152) (203)

Length Part No. B22-I-12 B22-I-16 B22-I-20 B22-I-24 B22-I-32 B22-I-36 B22-I-40 B22-I-48 B22-I-60 B22-I-72 B22-I-84 B22-I-96 B22-I-108 B22-I-120 B22-I-144 B22-I-168 B22-I-192 B22-I-216 B22-I-240

Design Load

mm

(39.9) (54.4) (68.9)

(3.56) (4.45) (5.34)

Wt./C

in.

mm

Lbs.

kg

12” 16” 20” 24” 32” 36” 40” 48” 60” 72” 84” 96” 108” 120” 144” 168” 192” 216” 240”

(305)

224 289 353 420 553 620 686 820 1018 1218 1417 1616 1816 2016 2416 2816 3216 3616 4016

(101.6)

(406) (508) (609) (813) (914) (1016) (1219) (1524) (1829) (2133) (2438) (2743) (3048) (3657) (4267) (4877) (5486) (6096)

(131.1) (160.1) (190.5) (250.8) (281.2) (311.1) (371.9) (461.7) (552.5) (642.7) (733.0) (823.7) (914.4) (1095.9) (1277.3) (1458.7) (1640.2) (1821.6)

Reference page 213 for general fitting and standard finish specifications

215

Strut Systems

Continuous Concrete Inserts B32I Continuous Concrete Insert

4” (101.6)

• Design Load for B32-I-12 thru B32-I-240 is 2,000 lbs. (8.89 kN) per foot of concrete MATERIAL: 12 Gauge (2.6) 11/2” insert length with safety factor of 3 in (38.1) 3000 psi concrete. • Loads concentrated within the last 2 inches (50.8 mm) of concrete inserts 27/8” 8” (203.2 mm) and longer should not (73.0) exceed 1,000 lbs. (4.45kN). • Concrete insert should be secured to the B32-I-3 Thru forms on 16” (406.4 mm) to 24” (609.6 mm) 11/16” intervals. B32-I-8 (17.4) • B32-I continuous concrete inserts are 25/8” made from B32 channel. Use channel 13/8” (66.7) nuts designed for use in B32 channel. (34.9) • B32-I concrete inserts are supplied with styrofoam fillers. B3332 end caps are furnished with inserts through 8” (203.2 mm) long, and B206 end caps are furnished 15/8” with inserts 12” (304.8 mm) and longer. 13/8” (41.3) • Material: Plain Steel ASTM A1011 (34.9) 33,000 PSI min. yield or Pre-Galvanized Styrofoam Steel ASTM A653SS 33,000 PSI min. B3332 Filler yield. End Cap • Finish: Plain, DURA GREEN™, Pre-Galv, B206 End Cap HDG B22-I-12

Length Part No.

in.

B32-I-3 B32-I-4 B32-I-6 B32-I-8

3” 4” 6” 8”

Wt./C

.188 Knockouts For Nailing Inserts To Forms Styrofoam Filler

THRU B22-I-240

Design Load

Lbs.

kg

Lbs.

kN

(76)

65 80 108 137

(29.5)

500 800 1000 1200

(2.22)

(101) (152) (203)

(36.3) (49.0) (62.1)

Wt./C

in.

mm

Lbs.

12” 16” 20” 24” 32” 36” 40” 48” 60” 72” 84” 96” 108” 120” 144” 168” 192” 216” 240”

(305)

202 262 316 376 496 556 616 736 915 1095 1274 1453 1633 1813 2173 2533 2893 3253 3613

(406) (508) (609) (813) (914) (1016) (1219) (1524) (1829) (2133) (2438) (2743) (3048) (3657) (4267) (4877) (5486) (6096)

kg

(91.6) (118.8) (143.3) (170.5) (225.0) (252.2) (279.4) (333.8) (415.0) (496.7) (577.9) (659.0) (740.7) (822.3) (985.6) (1148.9) (1312.2) (1475.5) (1638.8)

Reference page 213 for general fitting and standard finish specifications. Strut Systems

3/4”

(19.0)

216

(3.56) (4.45) (5.34)

Concrete Inserts

B32-I-12 B32-I-16 B32-I-20 B32-I-24 B32-I-32 B32-I-36 B32-I-40 B32-I-48 B32-I-60 B32-I-72 B32-I-84 B32-I-96 B32-I-108 B32-I-120 B32-I-144 B32-I-168 B32-I-192 B32-I-216 B32-I-240

(41.3)

mm

Length Part No.

15/8”

Continuous Concrete Inserts B52I Continuous Concrete Insert

4” (101.6)

• Design Load for B52-I-12 thru B52-I-240 MATERIAL: 12 Gauge (2.6) is 1,500 lbs. (6.67 kN) per foot of concrete 11/2” (38.1) insert length with safety factor of 3 in 3000 psi concrete. 3/4” • Loads concentrated within the last 2 (19.0) 5 2 /16” inches (50.8 mm) of concrete inserts (58.7) 8” (203.2 mm) and longer should not exceed 750 lbs. (3.33kN). .188 Knockouts For • Concrete insert should be secured to the Nailing Inserts To 11/16” forms on 16” (406.4 mm) to 24” (609.6 mm) Forms (17.4) intervals. B52-I-3 Thru • B52-I continuous concrete inserts are 13/16” B52-I-8 made from B52 channel. Use channel Styrofoam (20.6) nuts designed for use in B52 channel. 29/16” Filler • B52-I concrete inserts are supplied with (65.1) styrofoam fillers. B3352 end caps are furnished with inserts through 8” (203.2 mm) long, and B220 end caps are furnished 15/8” with inserts 12” (304.8 mm) and longer. 13/16” (41.3) • Material: Plain Steel ASTM A1011 (20.6) 33,000 PSI min. yield or Pre-Galvanized B3352 Styrofoam Steel ASTM A653SS 33,000 PSI min. End Cap Filler yield. B220 End Cap • Finish: Plain, DURA GREEN™, Pre-Galv, B52-I-12 THRU B52-I-240 HDG

Concrete Inserts

Length Part No.

in.

B52-I-3 B52-I-4 B52-I-6 B52-I-8

3” 4” 6” 8”

Wt./C Lbs.

kg

Lbs.

kN

(76)

53 63 85 106

(24.0)

400 500 750 1000

(1.78)

(152) (203)

Length Part No. B52-I-12 B52-I-16 B52-I-20 B52-I-24 B52-I-32 B52-I-36 B52-I-40 B52-I-48 B52-I-60 B52-I-72 B52-I-84 B52-I-96 B52-I-108 B52-I-120 B52-I-144 B52-I-168 B52-I-192 B52-I-216 B52-I-240

(41.3)

Design Load

mm

(101)

15/8”

(28.6) (38.5) (48.1)

(2.22) (3.33) (4.45)

Wt./C

in.

mm

Lbs.

kg

12” 16” 20” 24” 32” 36” 40” 48” 60” 72” 84” 96” 108” 120” 144” 168” 192” 216” 240”

(305)

157 202 237 282 373 419 464 556 692 829 965 1107 1237 1374 1648 1922 2196 2470 2744

(71.2)

(406) (508) (609) (813) (914) (1016) (1219) (1524) (1829) (2133) (2438) (2743) (3048) (3657) (4267) (4877) (5486) (6096)

(91.6) (107.5) (127.9) (169.2) (190.0) (210.4) (252.2) (313.9) (376.0 (437.7) (502.1) (561.1) (623.2) (747.5) (871.8) (996.1) (1120.4) (1244.6)

Reference page 213 for general fitting and standard finish specifications

217

Strut Systems

Spot Inserts B2500 Spot Insert

N2500 Insert Square Nut

• • • •

• For use in B2500 Spot Insert • Material: Steel ASTM A36 • Standard finish: ZN 11/4”

Design Load 600 Lbs. (2.67 kN) Safety Factor of 5 Order N2500 Nuts Separately Material: Steel ASTM A1011 33,000 PSI min. yield • Standard finish: ZN • Wt./C 46 Lbs. (20.8 kg) 2”

11/4” (31.7) 5/16”

(7.9)

(31.7)

31/4”

Part No.

Thread Size

(82.5)

N2500-1/4

1/4”-20

(50.8)

N2500-5/16 N2500-3/8 N2500-1/2 N2500-5/8 19/16” N2500-3/4 (65.0) N2500-7/8

Material: 12 Gauge (2.6)

11/2” (50.8)

Wt./C

5/16”-18 3/8”-16 1/2-13 5/8”-11 3/4”-10 7/8”-9

B2503 Heavy Duty Spot Insert

B2505 Thru B2508 Spot Insert

• Designed for use where heavy loads are required in curtain wall applications • Design Load is 5000 Lbs. (22.2 kN) with a Safety Factor of 3 • Loading based on two N225 channel nuts spaced 3” (76.2 mm) on center and a minimum of 2” (50.8 mm) from the end of the insert • Styrofoam end caps prevent concrete seepage into the channel • 12” (304.8 mm) long insert is anchored into the concrete at a depth of 51/2” (139.7 mm) • Material: 12 Gauge (2.6 mm) thick steel • Standard finish: ZN • Wt./C 42 Lbs. (19.0 kg)

• Safety Factor of 5 • To support 10” (250) pipe use B2505 insert with 5/8”-11 Channel Nuts. • To support up to and including 8” (200) pipes use B2506, B2507 and B2508 inserts with the desired Channel Nuts. • Standard finish: ZN

Part No.

B22 B32 B42 B52

Lbs.

kg

13 13 12 12 11 10 9

(5.9) (5.9) (5.4) (5.4) (5.0) (4.5) (4.1)

Channel Size

Channel End Cap Style Part No.

B2505 B2506 B2507 B2508

Thread Size

B3322 B3332 B3342 B3352

End Caps

25/8” (66.7)

51/16” (128.6)

Design Load Lbs.

kN

1200 1000 1000 1000

(5.34)

Maximum Pipe Size 10” 8” 8” 8”

(4.45) (4.45) (4.45)

(250) (200) (200) (200)

Wt./C Lbs.

kg

96 88 77 69

(43.5) (39.9) (34.9) (31.3)

Concrete Inserts

B2501 Light Duty Spot Insert 51/2” (139.7)

15/8” 2” 5/32” (4.0)

(41.3)

(50.8)

15/8”

DIA. NAIL HOLES

(41.3)

• Safety Factor of 2 • The concrete attachment problem solver for light duty applications. • Fast and easy applications. • No concrete leakage problems. • One piece unitized construction. • Color coded cap on thread for rod size identification and to prevent concrete seepage. (1/4”-Yellow, 3/8”-Red, 1/2”-Blue)

A

H

8”

11/4”

(203.2)

(31.7)

Design Load 12” (304.8)

Styrofoam End Caps

Part No. & Size B2501-1/4 B2501-3/8 B2501-1/2

Height A

Height H

In.

In.

mm

mm

27/16” (61.9) 31/16” (77.8)

7/8” (22.2) 17/8” (47.6)

41/8” (104.8)

17/8” (47.6)

Reference page 213 for general fitting and standard finish specifications. Strut Systems

218

Design Load

Wt./C

Lbs.

kN

Lbs.

kN

250 610 880

(1.11)

16 22 26

(7.2)

(2.71) (3.91)

(9.9) (11.7)

Insert Accessories B205, B206, B220 X Type End Caps

B3322, B3332, B3342, B3352 Y Type End Caps

• UL listed for raceway use only • Material: 12 Gauge (2.6) • Standard finish: ZN

• UL listed for raceway use only • Material: 14 Gauge (1.9) • Standard finish: ZN 5/8” (9.5) DIA.

A

25/8” (66.7)

A 1”

113/16”

(25.4)

(46.0)

Part No. B205 B206 B220

Use With B22 B32 B52

A In.

Wt./C mm

Lbs.

121/32” (42.0) 113/32” (35.7)

kg

10 (4.5) 8 (3.6) 4 (1.8)

27/32” (21.4)

13/4”

B380 Joint Splice Plate

Part No.

Use With

In.

A mm

Lbs.

Wt./C kg

B3322 B3332 B3342 B3352

B22 B32 B42 B52

1.270 1.000 .645 .460

(32.2)

15 15 15 15

(6.8)

(25.4) (16.4) (11.7)

(6.8) (6.8) (6.8)

B22IFS-B52IFS Styrofoam Filler Strip

(44.1)

• Used at splice points to prevent concrete seepage in long A continuous runs of concrete inserts. 1/16” • Material: 18 Gauge (1.2) (1.6) • Standard finish: GALV

29/32”

(23.0)

15/8” (41.3)

B A

Concrete Inserts

Part No. B380-22 B380-32 B380-42 B380-52

Use With B22 B32 B42 B52

A In.

Wt./C mm

15/8” (41.3) 13/8” (34.9) 1” (25.4) 13/16” (20.6)

Lbs.

11 10 9 7

kg

(5.0) (4.5) (4.1) (3.2)

A Part No. B22-IFS B32-IFS B52-IFS

Ft.

4’ 4’ 4’

B mm

In.

mm

(1219)

17/32” (309)

(1219)

1” (254) 21/32” (167)

(1219)

Wt./C Lbs.

kg

10 9 7

(4.5) (4.1) (3.2)

Pipe Sleeve Fasteners • Allows for rigid attachment of pipe sleeves to wall and floor forms for concrete pouring. • Accommodates Schedule 40, Schedule 80, or 5/16" (8) and smaller wall thickness. • Simply installed with a hammer.

Part No. BD40

Sleeve Diameter All Dia.

BD40

BE-5-8 & BE-9-12

Wall Thickness 5/16”

& under

BE-5-8

6”

Schedule 80 pipe

BE-9-12

9” - 14”

Schedule 80 pipe

Reference page 213 for general fitting and standard finish specifications

219

Strut Systems

Anchors Wedge Anchors Catalog Number

Thread Size

AWA-37-225 AWA-37-275 AWA-37-300 AWA-37-350 AWA-37-375 AWA-37-500 AWA-50-275 AWA-50-375 AWA-50-450 AWA-50-550 AWA-50-700

3/8"-16

3/8"

3/8"-16

3/8"

Thread Length

Size in.

21/4"

x x 23/4" 3/8" x 3" 3/8" x 31/2" 3/8" x 33/4" 3/8" x 5" 1/2" x 23/4" 1/2" x 33/4" 1/2" x 41/2" 1/2" x 51/2" 1/2" x 7"

3/8"-16 3/8"-16 3/8"-16 3/8"-16 1/2"-13 1/2"-13 1/2"-13 1/2"-13 1/2"-13

Drill/Hole Size

mm

in.

mm

(9 x 57) (9 x 70) (9 x 76) (9 x 89) (9 x 95) (9 x 127) (13 x 70) (13 x 95) (13 x 114) (13 x 140) (13 x 178)

11/4"

(32) (41) (47) (60) (66) (98) (35) (60) (79) (105) (143)

15/8" 17/8" 23/8" 25/8" 37/8" 13/8" 23/8" 31/8" 41/8" 55/8"

in. mm

Load Cap. Tension* lbs.

Load Cap. Shear*

kN

lbs.

kN

3/8” (9)

760 (3.38)

940 (4.18)

1/2” (13)

1390 (6.18)

1700 (7.56)

Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.

Hollow Base Drop-In Anchors Catalog Number

Rod Size

Overall Length in.

mm

in.

mm

in.

mm

ADH-25 ADH-37 ADH-50 9323 9343 9353

1/4”-20

7/8”

(22)

5/8”

(16)

3/8”

(9)

3/8”-16

15/16” 13/4” ----

(33)

15/16” (24)

5/8” (16)

(44)

11/4” (32) -------

3/4” (19)

1/2”-13 1/4” 3/8” 1/2”

Sleeve Length

----

Drill/Hole Diameter

----

Load Cap. Tension* lbs.

kN

285 (1.27) 520 (2.31) 1005 (4.47) -------

----

Load Cap. Shear* lbs.

kN

300 (1.33) 640 (2.84) 1005 (44.70) -------

Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.

RAPID ROD™ Hangers for Concrete Rod

Shank Size

Drill/Hole

Size

& Length

Size

in.

mm

Load Cap. Tension*

Load Cap. Shear* Lbs.

kN

in.

mm

Lbs.

kN

ARC-25-125

1/4”-20

1/4”

x 11/4” (6 x 32)

1/4”

(6)

485

(2.16)

610

(2.71)

ARC-37-150

3/8”-16

1/4”

x

11/2” (6 x 38)

1/4”

(6)

650

(2.89)

660

(2.93)

ARC-50-275

1/2”-13

3/8”

x

23/4” (9 x 70)

1/4”

(6)

1510 (6.71)

1580 (7.03)

Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.

RAPID ROD™ Hangers for Steel Catalog Number

Rod Size

Shank Size & Length in.

Load Cap. Tension* In 12 Ga.

mm

Lbs.

(6 x 25)

390

(1.75)

1260 (5.60)

x 1” * (6 x 25)

512

(2.28)

1260 (5.60)

11/2” (6 x 38)

390

(1.75)

1260 (5.60)

x 11/2” (6 x 38)

512

(2.28)

1260 (5.60)

390

(1.75)

1260 (5.60)

ARS-25-100

1/4”-20

1/4”

x 1”

ARS-37-100HN

3/8”-16

1/4”

ARS-37-150

3/8”-16

1/4”

x

ARS-37-150HN

3/8”-16

1/4”

ARS-37-200

3/8”-16

1/4”

x 2”

(6 x 51)

kN

Load Cap. Tension* In 1/4” Lbs.

kN

Note: Loads shown for ASTM A36 beams and ASTM A572 steel purlins include a safety factor of 4. For UL and FM listings, steel rapid rod must be installed with a retaining nut.

Reference page 213 for general fitting and standard finish specifications. Strut Systems

220

Concrete Inserts

Catalog Number

Anchors Plastic Screw Anchors • Kits contain 100 anchors, 100 screws, and 1 concrete drill bit Catalog

Screw

Number

Size

Load Cap. Tension* Lbs.

#8 x 1” #10 x 1” #12 x 1”

APC-8K APC-10K APC-12K

Load Cap. Shear*

kN

Lbs.

110 (0.49) 140 (0.62) 140 (0.62)

kN

70 (0.31) 90 (0.40) 90 (0.40)

Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.

Wood-Knocker™† Anchors Catalog Number

Rod Size

ACPW-25 ACPW-37 ACPW-50 ACPW-62 ACPW-75

1/4”-20

Color

3/8”-16 1/2”-13 5/8”-11 3/4”-10

Brown Green Yellow Red Purple

Insert Thread Length

Overall Length

Load Cap. Tension*

Load Cap. Shear*

in.

mm

in.

mm

lbs.

kN

3/8”

(9)

(47)

(16)

930 1200 1200 1160 1160

(4.13)

5/8”

17/8” 17/8” 17/8” 17/8” 17/8”

11/16” (17) 15/16” (24)

11/8” (28)

(47) (47) (47) (47)

lbs.

kN

370 (1.64) 1330 (5.91) 1840 (8.18) 2800 (12.45) 2800 (12.45)

(5.33) (5.33) (5.16) (5.16)

Notes: Based on normal weight concrete with minimum compression strength of 3,000 psi. Allowable load capacities are calculated using applied safety factor of 4. Minimum embedment is 2” (51mm). † Wood-Knocker™ is a trademark of Powers® Fasteners

Concrete Inserts

Bang-It™† Anchors Catalog Number

Rod Size

ACPD-25 ACPD-37 ACPD-50 ACPD-62 ACPD-75 ACPD-87

1/4”-20 3/8”-16 1/2”-13 5/8”-11 3/4”-10 7/8”-9

Color Brown Green Yellow Red Purple Black

Insert Thread Upper Deck Lower Deck Upper Deck Lower Deck Length Tension Load* Tension Load* Shear Load* Shear Load* in.

mm

lbs.

kN

lbs.

kN

lbs.

kN

lbs.

kN

3/8”

(9)

(4.94)

625 837 837 837 837 837

(2.78)

625 837 837 837 837 837

(2.78)

(16)

830 830 830 990 990 990

(3.69)

5/8”

1112 1435 1775 2200 2200 2200

11/16” (17) 15/16” (24)

11/8” (28) 15/16” (33)

(6.38) (7.89) (9.78) (9.78) (9.78)

(3.69) (3.69) (4.40) (4.40) (4.40)

(3.72) (3.72) (3.72) (3.72) (3.72)

(3.72) (3.72) (3.72) (3.72) (3.72)

Notes: Based on normal weight concrete with minimum compression strength of 3,000 psi. Allowable load capacities are calculated using applied safety factor of 4. Minimum insert spacing of 12” (305mm), minimun end spacing of 12” (305mm). Minimum embedment is 2” (51mm). Length of sleeve is 33/8” (86mm. † Bang-It™ is a trademark of Powers® Fasteners

Reference page 213 for general fitting and standard finish specifications

221

Strut Systems

Anchors 1/4”

Concrete Screws

Catalog Number

Rod Size in.

ACS-125H ACS-175H ACS-225H ACS-275H ACS-325H

Drill/Hole Size

Load Cap. Shear*

in.

mm

lbs.

kN

lbs.

kN

1/4”

11/4” (6 x 32)

3/16”

(5)

(6 x 44)

3/16”

(5)

(6 x 57)

3/16”

(5)

(6 x 70)

3/16”

(5)

(6 x 82)

3/16”

(5)

205 205 205 205 205

(0.91)

13/4” 21/4” 23/4” 31/4”

265 265 265 265 265

(1.18)

1/4”

x x 1/4” x 1/4” x 1/4” x

mm

Load Cap. Tension*

(1.18) (1.18) (1.18) (1.18)

(0.91) (0.91) (0.91) (0.91)

Note: Based on 1” (25mm) embedment with concrete compression strength of 4,000 psi using applied safety factor of 4. Consult factory for loading of other embedment depths.

Self-Tapping Machine Screw Anchor Catalog Number ATM-37

Rod Size

Thread Depth

3/8”-16

Drill/Hole Size

Load Cap. Tension*

in.

mm

in.

mm

Lbs.

11/16”

(17)

1/2”

(13)

540 (2.40)

Load Cap. Shear*

kN

Lbs.

kN

825 (3.67)

Note: Based on concrete compression strength of 4,000 psi in uncracked concrete using applied safety factor of 4. Minimum concrete thickness 4” (101mm) with minimum embedment of 15/8” (41mm)

Wall Screws Catalog Number

Head Type

Thread Depth in.

Minimum Embedment mm

Load Cap. Tension*

Load Cap. Shear* Lbs.

in.

mm

Lbs.

kN

kN

Combo

3/16”

x 11/4” (5 x 32)

3/4”

(19)

90

(0.40)

260 (1.15)

AWS-OH

Oval

3/16”

x

11/4” (5 x 32)

3/4”

(19)

90

(0.40)

260 (1.15)

AWS-PH

Pan

3/16”

x 11/4” (5 x 32)

3/4”

(19)

90

(0.40)

260 (1.15)

AWS-CH

Sleeve Type Expansion Anchors Catalog Number

Anchor Size & Length in.

ASA-37-187HN ASA-37-300HN ASA-37-400HN ASA-50-225HN ASA-50-300HN ASA-50-400HN ASA-50-525HN ASA-50-600HN

3/8”

x

3/8”

mm

17/8” (9 x 47)

x 3” (9 x 76) 3/8” x 4” (9 x 101) 1/2” x 21/4” (13 x 57) 1/2” x 3” (13 x 76) 1/2” x 4” (13 x 101) 1/2” x 51/4” (13 x 133) 1/2” x 6” (13 x 152)

Thread Length in.

mm

Drill/Hole Minimum Diameter Embedment in.

Load Cap. Tension*

Load Cap. Shear*

mm

in.

mm

lbs.

kN

lbs.

kN

15/8” (41)

3/8”

(9)

15/8”

(41)

3/8”

(9)

(41)

(41)

3/8”

(9)

(57)

1/2” (13)

(57)

1/2” (13)

(57)

1/2” (13)

(57)

1/2” (13)

(57)

1/2” (13)

15/8” 15/8” 21/4” 21/4” 21/4” 21/4” 21/4”

610 610 610 1055 1055 1055 1055 1055

(2.71)

(41)

670 670 670 1255 1255 1255 1255 1255

(2.98)

15/8” 15/8” 21/4” 21/4” 21/4” 21/4” 21/4”

(41) (57) (57) (57) (57) (57)

(2.98) (2.98) (5.58) (5.58) (5.58) (5.58) (5.58)

Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.

Reference page 213 for general fitting and standard finish specifications. Strut Systems

222

(2.71) (2.71) (4.69) (4.69) (4.69) (4.69) (4.69)

Concrete Inserts

Note: Based on concrete compression strength of 4,000 psi. Allowable load capacities are calculated using an applied safety factor of 4.