D-Show Profile Hardware Accessories Installation Guide For VENUE D-Show Profile Systems Assembling and Attaching the Video Monitor Mount to D-Show Profile D-Show Profile includes a Video Monitor Mount for your VGA monitor. Follow the instructions in this section to attach your video monitor to the mounting hardware.

3 Attach your monitor to the Video Monitor Mount by doing

either of the following, as appropriate for your video monitor: 100mm (MIS-D100) Attach the U bracket to the included mounting plate using the provided hardware. To complete the assembly, remove the 4 mounting screws from the back of the video monitor, line up the holes of the mounting plate, and use the screws you removed to secure the plate to the back of your monitor. back

Assembling the Video Monitor Mount requires the following items: • A VGA flat panel display with 100mm or 75mm mounting compatibility • A medium sized Phillips screwdriver • A table or similar clear, flat area with a towel or other padded surface (big enough to safely lay your video monitor face down)

screws screws

Mounting arm (top) U bracket Mounting plate Video monitor

front

Attaching a 100mm VGA monitor to the mounting plate, U bracket and mounting arm, viewed from the top edge of the monitor

75mm (MIS-D 75) Use the included U bracket. Remove the appropriate screws from the back of your monitor and use them to secure the U bracket to the back of the monitor.

Assembling the Video Monitor Mount back

The Video Monitor Mount is assembled by attaching a flat panel VGA monitor to the mounting arm. Both the 100mm and 75mm VESA (FDMI) video mounting standards are supported.

screws Mounting arm screws U bracket front

Video monitor

Attaching a 75 VGA monitor to the U bracket and mounting arm, viewed from the top edge of the monitor

To assemble the Video Monitor Mount: 1 Remove the Video Monitor Mount components from their packaging. Components include two T-bolts, two knurled locking nuts, the mounting arm, a U bracket, an additional mounting plate (for 100mm monitors only), and screws.

4 Hold the mounting arm face down so that the narrow (top)

end is against the back of the U bracket. Make sure the arm is facing the correct way, and attach the arm to the U bracket using the four screws provided. 5 Make sure all screws are tightened securely before attaching

(top) U bracket

the assembled video mount to the console.

Mounting Arm

T-bolt (2) Locking Nut (2) Components of the Video Monitor Mount 2 Make sure your video monitor is powered off and disconnected, and lay it face down on a padded table.

D-Show Profile Hardware Accessories Installation Guide 1

Attaching the Video Monitor Mount to D-Show Profile

Removing and Attaching the Video Monitor Mount

To attach the Video Monitor Mount to the console:

To remove the Video Monitor Mount:

1 From the back of the console, locate the Video Mount slot below the edge of the outermost back panel extrusion.

1 Stand at the back of the console.

2 Take one of the T-bolts included with the Video Mount and

that secure the Video Monitor Mount to the extrusion on the back of the console.

insert it into the wider opening at the far left end of the Video Mount slot. Slide the T-bolt to the right along the slot until it stays in the track.

2 Holding the VGA screen in one hand, loosen the lock nuts

3 Slide the Video Monitor Mount straight back off the T-bolts. 4 Tighten the lock nuts to secure the T-bolts and locking nuts

in place. To attach the assembled Video Monitor Mount to the console: 1 Loosen the two lock nuts securing the T-bolts in place, along the extrusion at the back of the console.

Video Mount slot Location of the Video Mount slot 3 Take the second T-bolt, insert it into the opening at the left and slide it to be a few inches away from the first T-bolt.

2 Position the Video Monitor Mount so that its base slots line up with the T-bolts, and slide the Video Monitor Mount into position. 3 Tighten the lock nuts to secure the mount into place.

4 Take the two silver lock nuts (thumb nuts) and thread them

loosely onto the T-bolts (do not tighten them). 5 Pick up the assembled Video Monitor Mount and hold it at the bottom of the VGA monitor, so you can balance the unit with one hand. 6 Position the base of the video mount under the back panel extrusion and feed the T-bolts through the two slots on the front edge of the arm assembly. Loosen the lock nuts if necessary. 7 Tighten the lock nuts thumb nuts to secure the Video Mon-

itor Mount in position. To move the monitor left or right: 1 Loosen the thumb nuts slightly. 2 Slide the Video Monitor Mount to the left or right, being carefully not to twist it off either of the T-bolts. (If the mount comes off the T-bolts, simply reattach it and resume). 3 When in the desired position, tighten the lock nuts.

To adjust the height of the monitor: 1 Determine the desired height and mark the location on the

mounting arm. 2 Detach the Video Monitor Mount from the console (see “Re-

moving and Attaching the Video Monitor Mount” on page 2). 3 Loosen the screws holding monitor (or the U bracket) to the mounting arm, and slide it down or up to the desired height. 4 Tighten all screws to secure the monitor in its new position.

D-Show Profile Hardware Accessories Installation Guide 2

Assembling and Attaching the Trackball Mount to D-Show Profile The Trackball Mount can be placed anywhere along the front edge of the console to provide a tray for your trackball or a mouse that accommodates left- or right-handed operation. A small hook underneath the Trackball mount lets you hang a pair of headphones.

Removing and Attaching the Trackball Mount The Trackball Mount can be removed quickly before packing or storing the console.

Always disconnect USB and headphones from the front panel ports before removing or attaching the Trackball Mount. To remove the Video Monitor Mount:

Assembling the Trackball Mount To attach the Trackball Mount

1 Holding the Trackball Mount in one hand, loosen the lock

nuts that secure it to the front of the console.

1 Unpack the Trackball Mount and components from their

2 Drop the Trackball Mount off track to remove the entire as-

packaging.

sembly from the console.

2 Make sure to unplug any USB or headphone connections at

3 Replace the lock nuts onto the T-bolts and tighten them

the front of the console.

down, to secure them in place.

3 From the front of the console, locate the slot for the Trackball mount (located below the extrusion).

To attach the assembled Trackball Mount to the console:

4 Take one of the T-bolts included with the Trackball Mount

and insert it into the opening at the right end of the Trackball Mount slot. Slide the T-bolt to the left along the slot until it is just to the left of the front panel USB and headphone ports. 5 Take the second T-bolt, insert it into the opening at the right

1 Loosen the two lock nuts securing the T-bolts in place, along the extrusion at the front of the console. 2 Position the Trackball Mount so that its base slots line up

with the T-bolts, and slide the Trackball Mount into position. 3 Tighten the lock nuts to secure the mount into place.

and slide it into place a few inches away from the first T-bolt. 6 Take the two silver lock nuts (thumb nuts) and thread them loosely onto the T-bolts (do not tighten them). 7 Place the Trackball Mount in position so that you can feed

the T-bolts through the two slots on the lip of the Trackball Mount. 8 Move the Mount and T-bolts left or right to line up the opening in the mount with the front panel USB and Headphone ports. 9 Tighten the lock nuts to secure the assembled Trackball Mount to the console. 10 Reconnect USB and headphones to the front panel ports.

Copyright © 2007 Digidesign, a division of Avid Technology, Inc. All rights reserved. This guide may not be duplicated in whole or in part without the express written consent of Digidesign. Avid, Digidesign, D-Show, and Pro Tools are either trademarks or registered trademarks of Avid Technology, Inc. in the US and other countries. All other trademarks contained herein are the property of their respective owners. Product features, specifications, system requirements, and availability are subject to change without notice. PN 9340-57169-00 REV A 07/07

D-Show Profile Hardware Accessories Installation Guide 3

www.digidesign.com

DIGIDESIGN 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA Tel: 650.731.6300 Fax: 650.731.6399

TECHNICAL SUPPORT (USA) Tel: 650.731.6100 Fax: 650.731.6384

PRODUCT INFORMATION (USA) Tel: 800.333.2137

INTERNATIONAL OFFICES Visit the Digidesign website for contact information