the

to

®

a division of PABCO® building products, LLC

CONSTRUCTION GUIDE FIRE & SOUND RATED SYSTEMS

MGM CityCenter, Las Vegas, NV: Utilized approximately 18 mil s.f. of PABCO® Gypsum wallboard

2nd Edition

Fire Resistive Properties of Gypsum

G

ypsum—hydrous calcium sulfate—is an abundant, naturally occurring mineral quarried for a variety of uses, the most common, of course, being gypsum board. Roughly 90 percent of finished interior surfaces are covered today with gypsum products.

“The gypsum in the core of the board actually emits steam when exposed to fire and retards transfer through the panel. This slowdown provides extra time to evacuate a room or building.” It can, in a sense, be compared to what happens when a blowtorch is turned on a block of ice. Although the ice is being melted, one can hold a hand on the opposite side without being burned. Even though the ice gets very thin it effectively blocks the transfer of the intense heat and one’s hand would not be burned until the ice is melted.

Two molecules of water are chemically bound to each calcium sulfate group during the formation of the gypsum crystal. As a result, gypsum is about 21 percent chemically combined water. Calcium Sulfate Dihydrate One of the many unique properties of When gypsum-protected wood or steel gypsum is its ability to give up these structural members are exposed to a water molecules as steam when heated, in a process known fire, the chemically combined water (being released as calcination, making gypsum board ideally fire-resistant. as steam) acts as a thermal barrier until this slow process, known as calcination, is completed. The most important characteristic of drywall, say fire The temperature directly behind the plane of officials, is that it will not burn. “Statistics show that in calcination is only slightly higher than that of recent years, fewer people have died in fires in the U.S.,” boiling water (212°F), which is significantly says the Gypsum Association. “Naturally, there is no single lower than the temperature at which steel reason for the decline. But the diminished number has a begins losing strength or wood ignites. high correlation with the increased use of gypsum products Once calcination is complete, the in-place and other fire-resistant building materials,” they say. calcined gypsum continues to act as a barrier protecting the underlying structural members from direct exposure to flames.

Fire Safety in Building Design

F

ire safety today is one of the most critical issues in designing and constructing any modern structure. Of course, the basic goal and objective is to reduce the probability that a person in or adjacent to a building will be exposed to an unacceptable fire hazard as a result of the design and construction of the building. Although the potential for being killed or injured in a fire cannot be completely eliminated, fire safety in a building can be achieved through proven building design features intended to minimise the risk of harm to people from fire to the greatest extent possible.

Page #34

Designing a structure to ensure minimal risk or to meet a prescribed level of safety from fire is more complex than just the simple consideration of what building materials will be used. Our ability to design ever-more fire resistant structures emphasizes the vital importance architects and engineers face in selecting the proper building materials and fire-resistant assemblies to protect against loss of life, and limit fire impact on the community.

Fire & Sound Rated Systems

FIRE & SOUND RATED SYSTEMS

a division of PABCO® building products, LLC

"Quality to the Core"

R

Fire Resistance Assemblies:

PABCO® Gypsum is proud to list hundreds of UL fire tested assemblies shown on the opposite page. All of these assemblies are UL approved, and allow the use of one or more PABCO® products available from our extensive range of gypsum board product line. Each assembly is tested within a controlled laboratory setting, and receives individual engineering evaluations. The following design selection pages present a relative small fraction of the available approved assemblies. Individual designs are prefaced with a brief description and summary. The complete design, and updated information, may be found in the Underwriter Laboratories (UL) Fire Resistant Directory (www.ul.com), the Gypsum Association’s “Fire Resistance Design Manual” (GA-600) (www.gyspum.org), or by contacting PABCO® Gypsum Technical Services. PABCO® Gypsum type X products bear the UL Classification Mark and are covered by UL’s classification and Follow-Up Service. The facing page is a cross reference of appropriate PABCO® Gypsum panel products to use for different UL fire-resistive Designs. Although the systems are arranged herein (as well as the GA-600) in general groupings (i.e. walls and interior partitions, floor-ceilings, roof-ceilings, etc.), the listing of a system in a specific category is not intended to limit its use to that category. However, this shall not be interpreted to imply that vertical systems, such as walls and partitions, are permitted to arbitrarily be used in a horizontal orientation.1 1. Gypsum Association GA-600-2009, pg 7

Notes pertaining to design listings:

• • • •

Fire Resistance Ratings:

Underwriters Laboratories (UL), ASTM, and numerous building codes use fire-resistant ratings as a measure of fire-containment for varying types of building construction assemblies. In respect to buildings, the fire resistance rating classifies the ability of an assembly to confine and isolate fire within a zone comprised of fire resistance rated walls, ceiling and floor assemblies. These fire-resistance rated assemblies are tested, certified and listed in the directories of accredited Fire Testing Laboratories. The most up-to-date information is available at the fire testing laboratory website or from PABCO® Gypsum Technical Services.

For more information:

• Refer to Underwriters Laboratories (UL) Fire Resistance Directory at www.ul.com. • Refer to the Gypsum Association Fire Resistance Design Manual, publication GA-600. • Contact PABCO® Gypsum Technical Services, or your qualified PABCO® Gypsum Field Representative (please reference the back cover of this publication for contact information).

Abbreviations:

Spacing of stud, joist, or trusses are maximum for fire rating Size of the studs are minimum Metal studs and runners are nominal 25 gage unless otherwise specified Metal studs and runners greater than specified as tested shall be permitted, however STC ratings may be negatively effected

Agency

Fire

Agency

Sound

Sound Ratings

ASTM

American Society for Testing and Materials Consulting Engineers Group Gypsum Association (Fire Resistance Design Manual GA-600) Ohio State University University of California Underwriters Laboratories Inc Warnock Hersey International Factory Mutual Intertek Testing Services NA Inc Southwest Research Institute Western Fire Center, Inc.

BBN G&H CK KAL RAL SA USG NGCTS

Bolt, Beranek and Newman Geiger & Hamme Cedar Knolls Acoustical Labs Kodaras Acoustical Laboratories Riverbank Acoustical Laboratories Shiner & Assoc. USG Corporation National Gypsum Corp Testing Service

CAC

CEG GA OSU U of C UL WHI FM ITS SwRI WFCi

Page #36

IIC STC

Ceiling attenuation class per ASTM procedures Impact insulation class per ASTM procedures Sound transmission class per ASTM procedures

SJ B4--22-09/ Fire Rated Systems/ PABCO® Gypsum

a division of PABCO® building products, LLC

"Quality to the Core"

R

UL FIRE RATED SYSTEM ASSEMBLY CROSS REFERENCE by PRODUCT PABCO® products currently manufactured below are appropriate to use in the following UL Fire Rated Assemblies, as shown in UL CKNX.R7094. March 2009

PABCO® Product • 5/8" FLAME CURB® type X

UL Core PG-11*

• 5/8" Soffit Board type X * (PG-11 replaces PG-9)

• 5/8" FLAME CURB® Super C

Type C

• 5/8" Soffit Board Super C

• 1/2" FLAME CURB® Super C

PG-C

• 1/2" FLAME CURB® type XXX • 1/2" Soffit type XXX

PG-3

width

UL Fire Rated System Assembly listing

46" 5/8 in. thick, 46 to 54 in. wide, Type PG-11 for use in Design Nos.: G501, G503, to G505, G507, G508, G531, L501, L508, L532, L556, L591, N501, N502, N505, 54" P508, P510, P511, P517, P540, P541, U017, U026, U207, U208, U301, U302, U305, U309, U321, U326, U329, U330, U337, U338, U339, U341, U342, U344, U351, U354, U355, U356, U357, U358, U360, U364, U368, U369, U374, U379, U411, U418, U420, U421, U425, U434, U436, U439, U442, U445, U449, U450, U460, U465, U466, U467, U469, U473, U485, U487, U494, U502, U504, U505, U506, U510, U512, U603, U606, U609, U615, U617, U622, U625, U637, U640, V417, V419, V421, V431, X508, X510, X516, X517, X525, X526, X527, X528. 48" 5/8 in. thick, 4 ft wide, Type C for use in Design Nos.: D301, D501, D502, G501, G503, G505, G512, G515, G521, G523, G525, G526, G527, G528, G529, G530, G531, G538, J501, J502, J503, J504, L501, L505, L508, L511, L512, L513, L514, L516, L520, L523, L525, L526, L527, L528, L529, L530, L538, L539, L540, L541, L548, L588, L591, L592, N501, N502, N505, P501, P502, P503, P504, P505, P506, P507, P508, P509, P510, P513, P514, P519, P549, U023, U301, U302, U305, U309, U311, U329, U333, U334, U340, U342, U354, U355, U379, U411, U428, U429, U442, U445, U451, U457, U465, U466, U467, U469, U473, U485, U501, U502, U504, U505, U506, U510, U512, U602, U603, U605, U617, U618, U627, U634, U635, U639, U640, U642, U643, U644, U645, V414, V417, V419, X501, X502, X504, X508, X509, X516, X517, X525, X526, X527, X528. 1/2 in. thick, 4 ft wide, Type PG-C for use in Design Nos.: G502, G504, G515, 48" G523, G524, G526, G527, G528, G529, G530, G531, G533, G534, L502, L503, L504, L507, L510, L512, L514, L524, L525, L530, L542, P237, P510, P512, U312, U317, U320, U406, U410, U412, U426, U428, U429, U435, U436, U438, U440, U441, U443, U444, U448, U451, U452, U453, U454, U455, U467, U474, U478, U601, U603, U608, U611, U613, U614, U619, U620, U910, U912, U914, V418, X507, X513, X514, X515, X518, X520, X521, X522, X523, X524, X530, X531. 48" 1/2 in. thick, 4 ft wide, Type PG-3 for use in Design Nos.: G502, G504, G523, G524, G526, G528, L502, L503, L504, L507, L580, P237, U312, U317, U410, U502, U603, U608, U611, U613, U614, U619, U620, X513, X520. 46" 1/2 in. thick, 46 to 54 in. wide, Type PG-3 for use in Design Nos.: to 54" G504, L503, L504, U317, U502, U611, U613, U614.

• 5/8" WATER CURB® type X 48"

• 5/8" MOLD CURB® Plus type X • 5/8" Gypsum Sheathing type X • 5/8" MOLD CURB® Plus Sheathing type X

PG-5W PG-5WS

• ABUSE CURB™ • 1" PABCORE® SHAFTLINER, • 1" PABCORE® MOLD CURB® Plus SHAFTLINER

PG-10

5/8 in. thick, 4 ft wide, Type PG-3W , PG-3WS , PG-5W or PG-5WS for use in Design Nos.: U301, U305, U342, U354, U355, U379.

46" 5/8 in. thick, 46 to 54 in. wide, Type PG-5W or PG-5WS for use in to 54" Design Nos.: U301, U305, U354, U379. 24" 1 in. thick, 24 in. wide Type PG-10 for use in Design Nos. U428, U429. the

to

®

Updates and current information: Information referred to in this document may change without notice. Visit www.ul.com for current information, or call PABCO® Technical Services @ 866-282-9298

Page #37

SJ- 4-18-11 PABCO® Gypsum

GUIDE to ASSEMBLIES - Fire & Sound GUIDE OVERVIEW: This GUIDE to ASSEMBLIES presents a small selection of assemblies in which PABCO® Gypsum products have been approved for use. There are numerous other approved assemblies available within each of the following sections.

Fire Rating

STC

GA File Number

Page

WALLS & INTERIOR PARTITIONS Steel Framed 1 hr

55-59

WP 1015

40

1 hr

50-54

WP 1021

40

1 hr

45-49

WP 1070

40

Listed within each section (for example: Walls & Interior Partitions, Steel Framed), assemblies are arranged sequentially in increasing fire ratings. Within each grouping of fire ratings (for example, one hour), the assemblies’ Sound Ratings (STC) are listed in decreasing order of STC.

1 hr

40-44

WP 1206; (UL U425)

40

1 hr

35-39

WP 1350;

40

2 hr

55-59

WP 1521

41

2 hr

55-59

WP 1522

41

2 hr

50-54

WP 1545

41

2 hr

50-54

WP 1548

41

2 hr

45-49

WP 1616; (UL411)

42

Each assembly listing provides a reference to the Gypsum Association File Number and/or UL Design Number for additional information, as well as the page number directing you to the test description listed on the following pages of this guide.

2 hr

45-49

WP 1635; (UL U425)

42

2 hr

40-44

WP 1716; (UL U425)

42

2 hr

50*

(UL U421) *STC Estimated

42

3 hr

50-54

WP 2022; (UL U435)

43

4 hr

55-59

WP 2961; (UL U435)

43

As this is a “selection” of assemblies for which PABCO® products have been approved for use, it is important to note that there are numerous other approved assembles. These additional assemblies are described in detail in the Gypsum Association Fire Resistant Design Manual GA-600 (current is the 19th edition), as well as within UL’s Certification Directory CKNX.R7094 (see UL® Fire Rated Systems Product Selection Guide, previous page).

WALLS & INTERIOR PARTITIONS, CHASE WALLS Wood Framed 45 m

(UL U317)

44

1 hr

50-54

WP 3241; (UL U311)

44

1 hr

50-54

WP 3242; (UL U309)

44

1 hr

50-54

WP 3243; (UL U309)

44

1 hr

45-49

WP 3370; (UL U305)

45

1 hr

45-49

WP 5512; (UL U305)

45

1 hr

40-44

WP 3880; (UL U305)

45

1 hr

40-44

WP 5515; (UL U305)

45

1 hr

35-39

WP 3510; (UL U309; UL U314)

46

1 hr

35-39

WP 3514

46

1 hr

35-39

WP 3520

46

1 hr

30-34

WP 3605

46

2 hr

55-59

WP 3812

46

2 hr

55-59

WP 3810

47

2 hr

55-59

WP 3820; WP 5520

47

2 hr

50-54

WP 3910, WP 5530; (UL R4024)

47

2 hr

40-44

WP 4135, WP 4136

47

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

Page #38

SJ 6-14-11/Guide to Fire Rated Systems/ PABCO® Gypsum

GUIDE to ASSEMBLIES - Fire & Sound Fire Rating

STC

GA File Number

Page

SHAFT WALL SYSTEMS

Fire Rating

STC

GA File Number

Page

ROOF CEILING - Wood Framed

1 hr

45-49

WP 6800

48

1 hr

RC 2608; (UL P549)

58

2 hr

50-54

WP 7051; (UL U428)

48

1 hr

RC 2602

58

2 hr

50-54

WP 7052; (UL U429)

48

2 hr

RC 2750; (UL L556)

58

2 hr

45-49

WP 7082

49

2 hr

RC 2751; (UL L556)

59

2 hr

45-49

WP 7083

49

AREA SEPARATION WALL SYSTEMS

COLUMNS

2 hr

60-64

ASW 0985

50

Light Tubular Columns:

2 hr

50-54

ASW 1100

50

1 hr

CM 1452; (UL X528)

60

2 hr

50-54

ASW 1105

50

1 hr

CM 1851, (UL X528)

60

1.5 hr

CM 2455; (UL X531)

60

2 hr

CM 2455; (UL X528)

60

FLOOR CEILING - Steel Framed 1 hr

FC 4340

51

Column 10WF-49

FC 4529, (UL L524)

51

1 hr

CM 1001; (UL X528)

60

(UL L527)

51

2 hr

CM 2017; (UL X528)

61

FC 4750; (UL L556)

51

3 hr

CM 3120; (UL X509, X510)

61

50-54

FC 2030; (UL G514)

52

4 hr

(UL X501)

61

50-54

FC 3012; (UL G512)

52

Column 14WF-228

50-54

1 hr 1.5 hr 2 hr 2 hr 2 hr

FLOOR CEILING - Wood Framed

2 hr

CM 2110; (UL X520)

61

3 hr

CM 3130; (UL X513)

61

1 hr

55-59

FC 5105; (UL L502)

53

1 hr

55-59

FC 5107; (UL L514)

53

1 hr

50-54

FC 5111

53

1 hr

50-54

FC 5116; (UL L516)

53

1 hr

BM 1137; (UL L524)

62

1 hr

50-54

FC 5120

54

2 hr

BM 2120; (UL N501)

62

1 hr

45-49

FC 5241

54

1 hr

45-49

FC 5250; (UL L502)

54

1 hr

35-39

FC 5415; (UL L513)

54

1 hr

35-39

FC 5406

55

1 hr

35-39

FC 5407

55

1 hr

35-39

FC 5410; (UL L512, L522, L503, L519)

55

1 hr

35-39

FC 5420; (UL L501)

55

1 hr

FC 5520; (UL L592)

56

1 hr

FC 5515; (UL L528)

56

2 hr

FC 5751; (UL L556)

56

2 hr

FC 5710; (UL L511)

57

2 hr

FC 5724; (UL L505)

57

2 hr

FC 5750; (UL L556)

57

BEAMS & GIRDERS

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

Page #39

SJ 6-14-11/Guide to Fire Rated Systems/ PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

WALLS & INTERIOR PARTITIONS Steel Framed

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

Construction Detail

File No

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, STEEL STUDS

NA

1hr

4-1/4˝

Face layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel to each side.

WP 1015 55-59

Base layer PABCO® 1/4" Regular gypsum wallboard applied parallel to each side of 2-1/2" steel studs 24" o.c.

4-1/4˝

Joints staggered 24" each layer and side. Sound tested with 1-1/2" mineral fiber insulation, 3.0 pcf, friction fit in stud space.

4˝

1 hr

Sound Test: CK 684-14

NON-LOAD BEARING

PABCO® GYPSUM WALLBOARD, STEEL STUDS

NA

Fire Test: See WP 1051 (FM WP 152-1)

One layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to ONE SIDE of 2-1/2" steel studs 24" o.c.

Fire Test: FM WP 66

OPPOSITE SIDE: Base layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to studs. Face layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to studs.

WP 1021

50-54

4˝

Joints staggered 24" each layer and side. Sound tested with 3-1/2" glass fiber insulation friction fit in stud space and all layers screw attached without adhesive.

Sound Test: RAL TL88-55

NON-LOAD BEARING

PABCO® GYPSUM WALLBOARD, STEEL STUDS, MINERAL FIBER INSULATION

1 hr

45-49 WP 1070

3-1/2˝

One layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 2-1/2" steel studs 24" o.c. 2" mineral fiber insulation, 2.5 pcf, friction fit in stud space. Also fire tested with 1-1/2" mineral fiber insulation, 3.0 pcf, stapled to board in stud space. Joints staggered 24" on opposite sides

Fire Test: FM WP 51-1, OSU T-3362, Sound Test: RAL TL69-42

NON-LOAD BEARING PABCO® GYPSUM WALLBOARD, STEEL STUDS

1 hr

40-44 WP 1206

4-3/4˝

One layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel to each side of 3-1/2" 20 gage steel studs 24" o.c. Joints staggered 24" on opposite sides.

Fire Test: UL NC 505-2, UL DESIGN U425 Sound test: see WP 1350 NGC 2385

Bracing requirement. LOAD BEARING PABCO® GYPSUM WALLBOARD, STEEL STUDS

1 hr

35-39 WP 1350

One layer 5/8" FLAME CURB® type X gypsum wall board, 5/8" WATER CURB®, or 5/8" PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 3-5/8" steel studs 24" o.c. 4-7/8˝

Joints staggered 24" on opposite sides. NON-LOAD BEARING

Fire Test: FM WP-45; OSU T-1770; ULC 79T484, 79T500, 79T497, ULC Design W415 Sound Test: NGC 2005004 RAL TL06-114

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #40

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

WALLS & INTERIOR PARTITIONS Steel Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

GA Rating Rating File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, STEEL STUDS

NA 2 hr

5-5/8˝

WP 1521

Base layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 3-5/8" steel studs 24" o.c. Face layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side. Joints staggered 24" each layer and side. Sound tested with 3-1/2" glass fiber friction fit in stud space. NON-LOAD BEARING

55-59

Sound Test: NRCC 815-NV

5-5/8˝

PABCO® GYPSUM WALLBOARD, STEEL STUDS

NA

2 hr

Fire Test: See WP 1545 (UC; ULC 80T499 ULC Design W414)

6-1/8˝

Face layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel or at right angles to each side.

WP 1522

55-59

Base layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 3-5/8" steel studs 24” o.c.

6-1/8˝

Fire Test: See WP 1548 (WHI-495-0236

Sound Test: NRCC 818-NV

Joints staggered 24" each layer and side. Sound tested with 3-1/2" glass fiber friction fit in stud space. NON-LOAD BEARING PABCO® GYPSUM WALLBOARD, STEEL STUDS

NA

4-1/2˝

Base layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 2-1/2" steel studs 24" o.c. Face layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 1-5/8" steel studs 24" o.c.

2 hr

WP 1545

Joints staggered 24" each layer and side. Sound tested with 1-1/2" mineral fiber insulation friction fit in stud space. 4-1/2˝

50-54

NON-LOAD BEARING

PABCO® GYPSUM WALLBOARD, STEEL STUDS

NA

2 hr

5˝

Base Layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 2-1/2" steel studs 24" o.c. Face layer: 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel or at right angles to each side.

WP 1548

Joints staggered 24" each layer and side.

50-54

5˝

Fire Test: UC, ULC 80T499, ULC Design W414 Sound Test: CK 654-40

Fire Test: WHI-495-0236

Sound Test: WHI-218-1

Sound tested with 2-1/2" glass fiber insulation friction fit in stud space. NON-LOAD BEARING

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #41

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

WALLS & INTERIOR PARTITIONS Steel Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

GA Rating Rating File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel to each side of 3-5/8" steel studs 24" o.c.

2 hr

45-49 WP 1616

6-1/8˝

Face layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel to each side, laminating compound combed over entire surface. Metal base and top retainer channels.

Fire & Sound Test Numbers Fire Test: UL R1319-31 UL Design U411 Sound Test: NGC 2005005, RAL TL06-115,

Joints staggered 24" each layer and side. NON-LOAD BEARING PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 3-1/2" 20 gage steel studs 24" o.c.

2 hr

45-49 WP 1635

6-1/2˝

Second layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side.

Fire Test: UL NC 505-4 UL Design U425 Sound Test: Estimated

Face layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel or at right angles to each side. Studs attached to each side of floor and ceiling runners. Joints staggered 24" each layer and side. Bracing requirement. LOAD BEARING PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 5/8" FLAME CURB® type X gypsum wallboard, 5/8" WATER CURB® type X backing board, or 5/8" PABCO® type X gypsum sheathing applied parallel to each side of 3-1/2” 20 gage steel studs 24" o.c.

2 hr

40-44 WP 1716

6˝

Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel to each side.

Fire Test: UL NC 505-6, UL Design U425 Sound Test: See WP 1615 (NGC 2250)

Joints staggered 24" each layer and side. Bracing requirement LIMITED LOAD BEARING GYPSUM WALLBOARD, STEEL STUDS

2 hr

NA

50*

Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied vertically or horizontally on both sides of the studs, with vertical joints centered over studs and staggered one stud cavity on opposite sides of studs. Horizontal edge joints (when applied horizontally) and horizontal butt joints (when applied vertically) on opposite sides of studs need not be staggered or backed.

Fire Test: UL Design U421 Sound Test: *Estimated

Remaining two layers 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied vertically or horizontally on one side of the wall. Horizontal butt joints staggered a min of 6 in. on adjacent layers. When used in widths other than 48 in., gypsum panels to be installed horizontally. NON-LOAD BEARING

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #42

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

WALLS & INTERIOR PARTITIONS Steel Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 1/2" FLAME CURB® Super C gypsum wallboard applied parallel to each side of 1-5/8" steel studs 24" o.c.

NA

3 hr

4-5/8˝

Face layer 1/2" FLAME CURB® Super C gypsum wallboard applied at right angles to each side.

WP 2922

50-54

Second layer: 1/2" FLAME CURB® Super C gypsum wallboard applied at parallel or at right angles to each side.

Sound Test: WEAL 87-118,

Joints staggered 24" each layer and side. 4-5/8˝

Sound tested with 1-1/2" glass fiber insulation friction fit in stud space. NON-LOAD BEARING

PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 1-5/8" steel studs 24" o.c. 5-5/8˝

NA

Fire Test: WHI-495-0804, UL R7094, UL Design U435

Second layer: 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel to each side.

Fire Test: WHI 495-0819; UL R7094, UL Design U435

Third layer 1/2" FLAME CURB® type XXX gypsum wallboard applied parallel or at right angles to each side.

4 hr

Face layer 1/2" FLAME CURB® type XXX gypsum wallboard applied at right angles to each side.

WP 2961

Sound Test: WEAL 87-119

Joints staggered 24" each layer and side.

55-59

5-5/8˝

Sound tested with 1-1/2" glass fiber insulation friction fit in stud space. NON-LOAD BEARING

the

to

®

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #43

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

WALLS & INTERIOR PARTITIONS, CHASE WALLS - Wood Framed

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

45 min

GA File No

Construction Detail

Fire & Sound Test Numbers

Description

Fire Test: UL U317

1/2” PABCO® FLAME CURB® type XXX, or 1/2” PABCO® FLAME CURB® Super C. NA

NA

4-1/2˝

LOAD BEARING - Nail Attached

PABCO® GYPSUM WALLBOARD, RESILIENT CHANNELS, MINERAL FIBER INSULATION, WOOD STUDS

1 hr

50-54 WP 3241

5-3/8˝

Resilient channels 24” o.c. attached at right angles to ONE SIDE of 2 x 4 wood studs 16” or 24” o.c. One layer of 5/8” FLAME CURB® Super C gypsum wallboard applied parallel to channels. End joints backblocked with resilient channels. 3” mineral fiber insulation, 2.0 or 2.3 pcf, in stud space. OPPOSITE SIDE: One layer of 5/8” FLAME CURB® Super C gypsum wallboard applied at right angles to studs.

Fire Test: Based on UL R3660-7, UL R2717-61, UL Design U311 Sound Test: Estimated

Vertical joints staggered 48” on opposite sides. Sound tested with studs 16” o.c. and open face of mineral fiber insulation blankets toward resilient channel-side of stud space. LOAD BEARING - Screw attachment PABCO® GYPSUM WALLBOARD, RESILIENT CHANNELS, MINERAL OR GLASS FIBER INSULATION, WOOD STUDS

1 hr

50-54 WP 3242

5-3/8˝

Resilient channels 16” o.c. attached at right angles to ONE SIDE of 2 x 4 wood studs 24” o.c. One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to channels with vertical joints located midway between studs. 3” mineral or glass fiber insulation in stud space.

Fire Test: Based on UL R14196, 05NK05371, UL Design U309 Sound Test: NRCC TL-93-098, IRC-IR-761,

OPPOSITE SIDE: One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to studs. Vertical joints staggered 24” on opposite sides. LOAD-BEARING - Nail attachment PABCO® GYPSUM WALLBOARD, RESILIENT CHANNELS, MINERAL OR GLASS FIBER INSULATION, WOOD STUDS

1 hr

50-54 WP 3243

5-3/8˝

Resilient channels 24” o.c. attached at right angles to ONE SIDE of 2 x 4 wood studs 24” o.c. One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to channels with vertical joints located midway between studs. 3” mineral or glass fiber insulation in stud space.

Fire Test: Based on UL R14196, 05NK05371, UL Design U309 Sound Test: NRCC TL-93-103, IRC-IR-761,

OPPOSITE SIDE: One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to studs. Vertical joints staggered 24” on opposite sides. LOAD-BEARING - Nail attachment

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #44

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

WALLS & INTERIOR PARTITIONS, CHASE WALLS Wood Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, WOOD STUDS One layer 5/8” FLAME CURB® type X gypsum wall board, 5/8” WATER CURB®, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of double row of 2 x 4 wood studs 16” o.c. on separate plates 1” apart.

1 hr

45-49 WP 3370

9-1/2˝

Joints staggered 16” on opposite sides. Horizontal bracing required at mid-height. LOAD BEARING - Nail Attachment

Sound Test: NRCC TL-93-261 IRC-IR-761

PABCO® GYPSUM WALLBOARD, WOOD STUDS One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of double row of 2 x 4 wood studs 16” o.c. on separate plates 1” apart.

1 hr

45-49 WP 5512

9-1/4˝

Joints staggered 16” on opposite sides. Horizontal bracing required at mid-height. LOAD BEARING - Nail attachment

One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 2 x 4 wood studs 16” o.c. staggered 8” o.c. on 2 x 6 wood plates.

40-44 WP 3380

7-3/4˝

Joints staggered 24” on opposite sides. Horizontal bracing required at mid-height. LOAD BEARING - Nail attachment

One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 2 x 4 wood studs 16” o.c. staggered 8” o.c. on 2 x 6 wood plates.

40-44 WP 5515

7-3/4˝

Joints staggered 24” on opposite sides. Horizontal bracing required at mid-height. LOAD BEARING - Nail attachment

Fire Test: See WP 3605 (UL R1319-4,-6, UL R2717-39, UL R3501-52, UL Design U305; ULC Design W301); UL R4024 Sound Test: NRCC TL-93-254, IRC-IR-761

PABCO® GYPSUM WALLBOARD, WOOD STUDS

1 hr

Fire Test: See WP 3605 (UL R1319-4, -6, UL R2717-39, UL R3501-52, UL Design U305; ULC Design W301); UL R4024 Sound: NRCC TL-93-261 IRC-IR-761

PABCO® GYPSUM WALLBOARD, WOOD STUDS

1 hr

Fire Test: See WP 3605 (UL R1319-4, 6, UL R2717-39, UL R3501-52, UL Design U305; ULC Design W301); UL R 4024

Fire Test: See WP 3605 (UL R1319-4,-6, UL R2717-39, UL R3501-52, UL Design U305; ULC Design W301); UL R4024 Sound Test: NRCC TL-93-254 IRC-IR-761

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #45

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

WALLS & INTERIOR PARTITIONS, CHASE WALLS Wood Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, WOOD STUDS

1 hr

1 hr

35-39

WP 3510

35-39 WP 3514

4-7/8˝

4-7/8˝

One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 2 x 4 wood studs 24” o.c. Joints staggered 24” on opposite sides. LOAD-BEARING - Nail Attachment.

Sound Test: NGC 2404

PABCO® GYPSUM WALLBOARD, WOOD STUDS

Fire Test: SWRI 01-4511619[1]

One layer of 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 2 x 4 wood studs 16” o.c. Joints staggered 16” on opposite sides. LOAD BEARING - Screw Attachment PABCO® GYPSUM WALLBOARD, WOOD STUDS

1 hr

35-39 WP 3520

4-7/8˝

Fire Test: UL R3501-47, -48, UL Design U309; UL R1319-129; UL Design U314

One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel to each side of 2 x 4 wood studs 24” o.c Joints staggered 24” on opposite sides.

Sound Test: See WP 3520 G&H NG-246FT

Fire Test: FM WP 90 Sound Test: G&H NG-246FT

LOAD-BEARING - Nail Attachment PABCO® GYPSUM WALLBOARD, WOOD STUDS

1 hr

30-34 WP 3605

NA

2 hr

4-7/8˝

11-1/4˝

LOAD-BEARING - Nail Attachment.

Sound Test: OR 64-8

PABCO® GYPSUM WALLBOARD, WOOD STUDS

Fire Test: See WP 3810 (FM WP 297)

Base layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to 2 x 4 wood studs 24” o.c. Face layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to studs over base layer and to top and bottom plates. Joints offset 24” from base layer joints. Inner layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel. Joints in inner layer need not be taped.

WP 3812

55-59

One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied parallel or at right angles to each side of 2 x 4 wood studs 16” o.c. Joints of square edge, bevel edge or predecorated wallboard may be left exposed. Joints staggered 16” on opposite sides.

Fire Test: UL R1319-4, -6, UL R2717-39, UL R3501-52, UL Design U305; ULC Design W301

11-1/4˝

Second wall duplicate of first wall and separated by 1” space. Walls independently loaded.

Sound Test: Estimated Based on WP 3810 (RAL TL73-215; RAL TL73-224)

Sound tested with 3-1/2” glass fiber insulation, 0.75 pcf, friction fit in stud spaces. LOAD BEARING - Nail Attachment PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #46

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

WALLS & INTERIOR PARTITIONS, CHASE WALLS Wood Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

GA Rating Rating File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, WOOD STUDS

2 hr

55-59 WP 3810

11˝

Base layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to 2 x 4 wood studs 24” o.c. Face layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” PABCO® FLAME CURB® Super C applied at right angles. Joints offset 24” from base layer joints. Inner layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied parallel to studs. Joints in inner layer need not be taped. Second wall duplicate of first wall and separated by 1” space. Walls independently loaded. STC 59 with 3-1/2” glass fiber insulation friction fit in stud spaces both sides; STC 57 without glass fiber insulation.

Fire Test: FM WP 297 Sound Test: RAL TL73-215, RAL TL73-224

LOAD BEARING - Nail Attachment PABCO® GYPSUM WALLBOARD, WOOD STUDS 10-3/4˝

NA

Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to each side. Joints staggered 16” each layer and side.

WP 3820

2 hr

&

WP 5520 10-3/4˝

55-59

Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to each side of double row of 2 x 4 wood studs 16” o.c. on separate plates 1” apart.

Fire Test: See WP 4135 (FM WP 360); UL R4024

Sound Test: NGC 3056

Sound tested with 3-1/2” glass fiber insulation stapled to studs in stud spaces on one side and with nails for base layer spaced 6” o.c.. Horizontal bracing required at mid-height. LOAD-BEARING - Nail Attachment PABCO® GYPSUM WALLBOARD, WOOD STUDS

2 hr

50-54

WP 3910 &

WP 5530

Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to each side of 2 x 4 wood studs 16” o.c., staggered 8” o.c. on 2 x 6 wood plates. 8˝

Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to each side. Joints staggered 16” each layer and side.

Fire Test: See WP 4135 (FM WP 360); UL R4024 Sound Test: NGC 2377,

Sound tested with nails for base layer spaced 6” o.c. Horizontal bracing required at mid-height. LOAD BEARING - Nail Attachment PABCO® GYPSUM WALLBOARD, WOOD STUDS

WP 4135 (Nail attached)

2 hr

6-1/8˝

40-44 WP 4136 (Screw attached)

Base layer 5/8” FLAME CURB® type X gypsum wall board, 5/8” WATER CURB®, or 5/8” PABCO® type X gypsum sheathing applied at right angles (parallel or at right angles for WP 4136) to each side of 2 x 4 wood studs 24” o.c. (16” o.c for WP 4136). Face layer 5/8” FLAME CURB® type X gypsum board applied at right angles to each side. Joints staggered 24” (16” o.c. for WP 4136) each layer and side. Sound tested with studs 16” o.c. (WP 4135 only). LOAD BEARING

Fire Test: FM WP 360, Sound Test: NGC 2363 Fire Test: SRWI 01-5920614, Sound Test: See WP4135 (NGC 2363)

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #47

SJ- 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

SHAFT WALL SYSTEMS

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

Construction Detail

File No

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, STEEL C-T STUDS

NA

1 hr

3-1/8˝

One layer 1” x 24” PABCORE® Shaftliner type X, or 1” x 24” PABCORE® MOLD CURB® Plus Shaftliner type X gypsum panels inserted between 2-1/2” floor and ceiling runners with T-Section of 2-1/2” steel C-T studs between panels. OPPOSITE SIDE: One layer of 5/8” PABCO® FLAME CURB® Super C gypsum wallboard applied parallel to studs.

WP 6800

Sound tested with horizontal resilient channels 24” o.c. and 2-1/2” glass fiber friction fit in stud space.

45-49

3-5/8˝

2 hr

3-1/2˝

One layer 1” x 24” PABCORE® Shaftliner type X, or 1” x 24” PABCORE® MOLD CURB® Plus Shaftliner type X gypsum panels inserted between 2-1/2” floor and ceiling J runners with T-Section of 2-1/2” steel C-H or C-T studs between panels. OPPOSITE SIDE: Base layer 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to studs.

WP 7051

Face layer 1/2” FLAME CURB® Super C gypsum wallboard applied parallel to studs.

50-54

3-1/2˝

3-1/2˝

2 hr

50-54

3-1/2˝

Sound Test: RAL TL93-181

NON LOAD BEARING

One layer 1” x 24” PABCORE® Shaftliner type X, or 1” x 24” PABCORE® MOLD CURB® Plus Shaftliner type X gypsum panels inserted between 2-1/2” floor and ceiling J runners with T-Section of 2-1/2” steel C-H or C-T studs between panels. Face layer 1/2” FLAME CURB® Super C gypsum wallboard applied parallel to studs with vertical joints midway between studs and laminated to 1” x 24” PABCORE® Shaftliner type X, or 1” x 24” PABCORE® MOLD CURB® Plus Shaftliner type X gypsum panels with 4” wide strips of taping compound at wallboard perimeter and vertical centerline.

WP 7052

Fire Test: UL R7094, 93NK8151, UL R3660, 07NK22992 UL Design U428

Sound tested with 1-7/8” glass fiber insulation in stud space.

PABCO® GYPSUM WALLBOARD, STEEL C-H or C-T STUDS

NA

Sound test: RAL TL96-28,

NON LOAD BEARING

PABCO® GYPSUM WALLBOARD, STEEL C-H or C-T STUDS NA

Fire Test: WHI-495-1303

OPPOSITE SIDE: One layer 1/2” FLAME CURB® Super C gypsum wallboard applied at rightangles to studs. Sound tested with 1-7/8” glass fiber in stud space.

Fire Test: See WP 7051 (UL R7094, 93NK8151, UL Design U429)

Sound Test: See WP 7051 (RAL TL93-181)

NON LOAD BEARING

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #48

SJ 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

SHAFT WALL SYSTEMS (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

Construction Detail

File No

Fire & Sound Test Numbers

Description

Fire Test: WHI 495-0528, WHI 495-0566

PABCO® GYPSUM BOARD, SLOTTED STEEL I STUDS 3-1/2˝

NA

2 hr

OPPOSITE SIDE: Base layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied at right angles to studs.

WP 7082

3-1/2˝

45-49

One layer 1” x 24” PABCO® PABCORE® SHAFTLINER type X, or 1”x 24” PABCORE® MOLD CURB® Plus SHAFTLINER type X inserted between 2-1/2” floor and ceiling runners with tabflange section of 2-1/2” slotted steel I studs between panels.

Sound Test: See WP 7083 (WEAL 84-108)

Face layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied parallel to studs. Sound tested with 1” glass fiber insulation friction fit in stud space. NON LOAD BEARING PABCO® GYPSUM WALLBOARD, SLOTTED STEEL I STUDS

3-1/2˝

NA

2 hr

One layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied parallel to each side.

WP 7083

45-49

One layer 1” x 24” PABCO® PABCORE® SHAFTLINER type X, or 1”x 24” PABCORE® MOLD CURB® Plus SHAFTLINER type X gypsum panels inserted between 2-1/2” floor and ceiling runners with tab-flange section of 2-1/2” slotted steel I studs between panels.

3-1/2˝

Fire Test: WHI 495-0569, WHI 495-0570

Sound Test: WEAL 84-108

Sound tested with 1” glass fiber insulation friction fit in stud space. NON LOAD BEARING

the

to

®

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #49

SJ 6-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

AREA SEPARATION WALLS

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, STEEL H STUDS

NA

Two layers 1” x 24” PABCORE® SHAFTLINER type X, or 1”x 24” PABCORE® MOLD CURB® Plus SHAFTLINER type X inserted between 2” floor and ceiling runners with 2” steel H studs between adjacent pairs of gypsum panels.

3-1/2˝

Fire & Sound Test Numbers Fire Test: WFCi #07073

NON LOAD BEARING ASFW 0985 Area Separation Fire Wall

ASW 0985

2 Hr

11-3/4˝

60-64

A 3/4” minimum air space must be maintained between steel components and adjacent framing (indicated by dashed lines in sketch). As an alternate, the steel components may be covered with 6” wide battens or full sheets of 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard. Sound tested with 2 x 4 stud wall faced with 1/2” PABCO® Regular wallboard each side of system and 3-1/2” glass fiber insulation in stud space.

PABCO® GYPSUM WALLBOARD, STEEL STUDS

3-5/8˝

NA

Sound Test: RAL TL07-373

Base layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 1-5/8” steel studs 24” o.c.

Fire Test: UC

Face layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied parallel to each side. Joints staggered 24” each layer and side. Sound tested with 1-1/2” mineral fiber insulation in stud space.

ASW 1100

2 Hr

50-54

Field Sound Test: ACI 1131a

PABCO® GYPSUM WALLBOARD, STEEL STUDS

Fire Test: UC

3-5/8˝

NA

4-1/2˝

Base layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied parallel to each side of 2-1/2” steel studs 24” o.c. Face layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied parallel to each side.

ASW 1105

2 Hr

NON LOAD BEARING

Joints staggered 24” each layer and side. Sound tested with 1-1/2” mineral fiber insulation in stud space. NON LOAD BEARING

50-54

Sound Test: CK 654-40

4-1/2˝

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #50

SJ 06-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

FLOOR CEILING - STEEL FRAMED

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

File No.

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, STEEL CHANNEL JOISTS, PLYWOOD FLOOR

NA

1 hr

FC 4340

50- 54

Base layer 1/2” PABCO®FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to resilient furring channels 16” o.c. Resilient furring channels applied at right angles to channel shaped, minimum 8” deep, 18 gage galvanized steel joists 16”o.c. Face layer 1/2” PABCO®FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to channels with end joints located midway between channels. Joints offset 24” from base layer joints. 3-1/2” glass fiber batt insulation in joist space. Floor of 5/8” T & G edge plywood applied at right angles to joists. STC tested with 1/4” carpet applied over a 3/8” foam pad. PABCO® GYPSUM WALLBOARD CEILING, STEEL CHANNEL JOISTS, PLYWOOD FLOOR

1 hr

1.5 hr

2 hr

NA

NA

NA

FC 4502

-

FC 4750

Base layer 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to channel shaped, minimum 7” deep, 18 gage galvanized steel joists 24” o.c. Face layer 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to joists. Joints offset from base layer joints. Steel joists supporting 5/8” T& G edge plywood floor applied at right angles to joists. For alternate floor systems, consult manufacturer.

Fire Test: NRCC A-4219.A Assembly FF-23

Sound Test: NRCC B-3163.2 IIC & Test: 69; NRCC B-3163.2

Fire Test: Based on UL R3660-7, -8; UL R1319-133; UL R7094, 90NK10635; UL Design L524

Two layers 5/8” PABCO® FLAME CURB® Super C type C gypsum wallboard applied with long dimension perpendicular to resilient channels. Upper layer attached to resilient channels. Butt joints to be centered under resilient channels. Face layer installed perpendicular to resilient channels and attached to resilient channels through upper layer. All long edge joints in face layer boards to be offset from long edge joints in upper layer a min of 16 in. Butt joints of face layer to occur between resilient channels with each end of butted boards attached to upper board.

Fire Test: UL L527

PABCO® GYPSUM WALLBOARD, WOOD FLOOR, STEEL CHANNEL JOISTS, RIGID FURRING CHANNELS

Fire Test: UL R4024, 02NK04478, UL Design L556; ULC Design M514

Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to channel shaped, minimum 8” deep, 18 gage galvanized steel joists 24” o.c. Second layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to joists. Second layer joints offset 24” from base layer joints. Third layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to joists. Third layer joints offset 12” from second layer joints. Hat-shaped rigid furring channels 24” o.c. applied at right angles to joists over third layer. Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to furring channels. Joists supporting 3/4” T & G edge plywood floor applied at right angles to joists.

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #51

SJ 06-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

FLOOR-CEILING STEEL FRAMED (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, STEEL JOISTS, CONCRETE SLAB One layer 1/2” PABCO® FLAME CURB® type XXX, or PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to rigid furring channels 24” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 54” long.

2 hr

50-54

FC 2030

Furring channels attached to open web steel joists 24” o.c. supporting 3/8” rib metal lath or 9/16” deep 28 gage corrugated steel and 2-1/2” concrete slab measured from top of flute. Furring channels may be attached to 1-1/2” cold rolled carrying channels 48” o.c. suspended from joists.

Fire Test: UL R3501-28, UL Design G514; ULC Design I511 Sound Test: NGC 4075

(Two hour restrained and unrestrained.) (See GA file No BM 3310) PABCO® GYPSUM WALLBOARD, STEEL JOISTS, CONCRETE SLAB One layer 5/8” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to furring channels 24” o.c. (double channels at end joints). 5/8” x 2-3/4” PABCO® FLAME CURB® type X gypsum wallboard strips over butt joints.

3 hr

50-54

FC 3012

Furring channels wire tied to open web steel joist 24” o.c. supporting 3/8” rib metal lath and 2- 1/2” concrete slab. (Three hour restrained and unrestrained.)

Fire Test: UL R1319-79; UL R3501, 88NK21023, Based on UL R3660-7, -8; UL R2717-61, UL Design G512 Sound Test: Est. see FC 2030 (NGC 4075)

the

to

®

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #52

SJ 06-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

FLOOR CEILING - WOOD FRAMED

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

GA Rating Rating File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, RESILIENT CHANNELS, WOOD JOISTS

NA

1 hr

FC 5105

55-59

One layer 1/2” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to resilient furring channels 24” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 60” long. Resilient channels applied at right angles to 2 x 10 wood joists 16” o.c. Wood joists supporting 19/32” plywood and 1” proprietary sanded gypsum underlayment. STC rated with 3-1/2” glass fiber insulation in joist spaces and with carpet and pad. Second layer of 1/2” or 5/8” type X gypsum wallboard required to achieve 1 hour fire resistance rating when glass fiber insulation is used. PABCO® GYPSUM WALLBOARD, RESILIENT CHANNELS, WOOD JOISTS, GYPSUM FLOOR UNDERLAYMENT

1 hr

55-59

FC 5107

One layer PABCO® 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to resilient furring channels 24” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 54” long. Resilient furring channels applied at right angles to 2 x 10 wood joists 16” o.c. Wood joists supporting 19/32” plywood subfloor and 3/4” 1000 psi sanded gypsum floor underlayment. PABCO® GYPSUM WALLBOARD, WOOD I-JOISTS, RESILIENT CHANNELS

NA

1 hr

FC 5111

50-54

Base layer PABCO® 1/2” FLAME CURB® type XXX, or PABCO® 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to resilient channels 16" o.c. Resilient channels applied at right angles to minimum 9-1/2” deep wood I-joists, with minimum 1-1/4” deep x 1-1/2” wide flanges and minimum 3/8” webs, 24” o.c. Face layer PABCO® 1/2” FLAME CURB® type XXX, or PABCO® 1/2” FLAME CURB® Super C gypsum applied at right angles to channels. Face layer end joints located midway between channels and attached to base layer. Edge joints offset 24” from base layer edge joints. Wood I-joists supporting 5/8” oriented strand board applied at right angles to I-joists.

Fire & Sound Test Numbers Fire Test: UL R6352, UL Design L502

Sound Test: G&H BW-10 MT IIC & Test: (73 C & P) G&H BW-10 MT

Fire Test: UL R1319-65, UL Design L514 Field Sound Test: INTEST 5-761-3

Fire Test: NRCC A-4440.1 (Revised)

Sound Test: NRCC B-3150.2 IIC & Test: (68 C & P) NRCC B-3150.2

STC and IIC tested with 40 oz carpet over 1/4” foam pad. PABCO® GYPSUM WALLBOARD, WOOD JOISTS, RESILIENT CHANNELS, GLASS FIBER INSULATION

1 hr

50-54

FC 5116

One layer 5/8” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to resilient furring channels 24” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 54” long. Resilient furring channels applied at right angles to 2 x 10 wood joists 16” o.c. Wood joists supporting 5/8” interior plywood with exterior glue subfloor and 1-5/8” perlite-sand concrete reinforced with No. 19 SWG galvanized hexagonal wire mesh. 3” glass fiber insulation 0.90 pcf in joist space stapled to subfloor.

Fire Test: UL R3453-7 Based on UL R3660-7, -8; R2717-61; Based on UL R7094, 90NK10635; Based on UL R8742, 88NK22591, UL Design L516 Sound Test: KAL L 224-28-65 IIC & Test: (74 C & P) KAL L 224-27-65

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #53

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

FLOOR-CEILING WOOD FRAMED (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, WOOD JOISTS, RESILIENT CHANNELS, GLASS FIBER INSULATION

1 hr

FC 5120

One layer PABCO® 1/2” FLAME CURB® type XXX, or PABCO® 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to resilient furring channels 24” o.c. Resilient channels applied at right angles to 2 x 10 wood joists 16" o.c. Wood joists supporting 5/8" interior plywood with exterior glue subfloor and 3/8" particleboard, 1.5 psf. 3-1/2" glass fiber insulation batts, 0.7 pcf, friction fit in joist cavities, supported by alternately every 12" by wire ords and resilient furring channels. Sound tested with carpet and pad and with insulation stapled to joists.

50-54

PABCO® GYPSUM WALLBOARD, WOOD I-JOISTS, RESILIENT CHANNELS

1 hr

45-49

FC 5241

Base layer PABCO® 1/2” FLAME CURB® type XXX, or PABCO® 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to resilient channels 16” o.c. Resilient channels applied at right angles to minimum 9-1/2” deep wood I-joists, with minimum 1-1/4” deep x 1-1/2” wide flanges and minimum 3/8” webs, 24” o.c. Face layer PABCO® 1/2” FLAME CURB® type XXX, or PABCO® 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to channels. Face layer end joints located midway between channels and attached to base layer. Edge joints offset 24” from base layer edge joints. Wood I-joists supporting 5/8” oriented strand board applied at right angles to I-joists. PABCO® GYPSUM WALLBOARD, WOOD JOISTS, RESILIENT CHANNELS

1 hr

45-49

FC 5250

One layer PABCO® 1/2” FLAME CURB® type XXX, or PABCO® 1/2” FLAME CURB® Super C gypsum applied at right angles to resilient furring channels 24” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 60” long. Resilient furring channels applied at right angles to 2 x 10 wood joists 16” o.c. Wood joists supporting 1” nominal wood subfloor and 1” nominal wood finish floor, or 19/32” plywood finished floor with long edges T & G and 15/32” interior plywood with exterior glue subfloor perpendicular to joists with joints staggered. PABCO® GYPSUM WALLBOARD, WOOD JOISTS, RESILIENT CHANNELS One layer 5/8” PABCO® FLAME CURB® Super C gypsum wallboard applied at right angles to resilient furring channels 16” o.c.

1 hr

35-39

FC 5415

Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 72” long. Resilient furring channels applied at right angles to 2 x 10 wood joists 24” o.c. Wood joists supporting 3/4” nominal interior plywood with exterior glue T & G subfloor perpendicular to joists with joints staggered. Underside of T & G joints covered between joist spaces with 6” x 22-1/2” x 5/8” type X gypsum wallboard battens attached to flooring.

Fire & Sound Test Numbers Fire Test: FM FC-181, 8-31-72

Sound Test: G&H OC-3MT, 10-31-71 IIC & Test: (73 C & P) G&H OC-3MT, 10-31-71 Fire Test: NRCC A-4440.1 (Revised) Sound Test: NRCC B-3150.1 IIC & Test: 40 (68 C & P) NRCC B-3150.1, NRCC B-3150.2

Fire Test: UL R2717-29, UL Design L502; ULC Design M501 Sound Test: RAL TL64-155 IIC & Test: 39 (67 C & P) See FC 5240 (CK 6512-6) Fire Test: UL R5229-2, UL Design L513 Sound Test: Estimated

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #54

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

FLOOR-CEILING WOOD FRAMED (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, WOOD JOISTS Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to 2 x 10 wood joists 24” o.c.

1 hr

35-39

FC 5406

Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to joists. Joints offset 24” from base layer joints. Wood joists supporting 1/2” plywood with exterior glue applied at right angles to joists.

Fire & Sound Test Numbers Fire Test: FM FC 172; ITS. Sound Test: Estimated

Ceiling provides one hour fire resistance protection for framing, including trusses. PABCO® GYPSUM WALLBOARD, WOOD I-JOISTS, Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to wood I-joists 24” o.c.

1 hr

35-39

FC 5407

Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to I-joists. Joints offset 24” from base layer joints.

Fire Test: FM FC 172, ITS Sound Test: Estimated

Wood I-joists supporting 1/2” wood structural panels applied at right angles to joists. Ceiling provides one hour fire resistance protection for I-joists. PABCO® GYPSUM WALLBOARD, WOOD JOISTS One layer 1/2” PABCO®FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied at right angles to 2 x 10 wood joists 16” o.c.

1 hr

35-39

FC 5410

Wood joists supporting 1” nominal T & G wood subfloor and 1” nominal wood finish floor, or 19/32” plywood finished floor with long edges T & G, and 15/32” interior plywood with exterior glue subfloor perpendicular to joists with joints staggered.

Fire Test: UL R1319-66, UL Design L512; UL R3501-45, UL Design L522; UL R2717-38, UL Design L503; UL R3543-6, UL Design L519; ULC Design M502 Sound Test: NGC 4024, IIC & Test: 32 (66 C & P) NGC 5032

PABCO® GYPSUM WALLBOARD, WOOD JOISTS One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to 2 x 10 wood joists 16” o.c.

1 hr

35-39

FC 5420

Wood joists supporting 1” nominal wood subfloor and 1” nominal wood finish floor, or 19/32” plywood finished floor with long edges T & G and 15/32” interior plywood with exterior glue subfloor perpendicular to joists with joints staggered.

Fire Test: UL R3501-5, 9, UL R1319-2, 3; UL Design L 501; ULC Design M500 Sound Test: See FC 5410 (NGC 4024) IIC & Test: 32 (66 C & P) NGC 5032

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #55

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

FLOOR-CEILING WOOD FRAMED (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

1 hr

1 hr

2 hr

NA

NA

NA

GA File No

Construction Detail

Description

Fire & Sound Test Numbers

PABCO® GYPSUM WALLBOARD, WOOD TRUSSES, WOOD STRUCTURAL PANELS, GYPSUM FLOOR TOPPING, RESILIENT CHANNELS, GLASS OR MINERAL FIBER BATT OR LOOSE FILL INSULATION, CEILING DAMPER One layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to resilient furring channels 12” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 60” long located 3” back on either side of end joint. Resilient channels applied at right angles to 18” deep parallel chord wood trusses 24” o.c. Glass or mineral fiber batt insulation stapled to subfloor or loose fill insulation applied directly over gypsum board. Wood trusses supporting 23/32” wood structural panel subfloor, long edges T & G, applied at right angles to trusses. Either 3/4” gypsum floor topping or 15/32” wood structural panel underlayment applied over subfloor. Optional ceiling damper (refer to manufacturer for information on the type of damper).

Fire Test: UL R7094, 07NK11121, UL Design L592; WFCi 07002C/07048

Fire Test: UL R9500-1, 80NK15492; UL R2717-61; UL Design L528

FC 5515

PABCO® GYPSUM WALLBOARD, WOOD TRUSSES One layer 5/8” PABCO® FLAME CURB® Super C type C gypsum wallboard applied at right angles to rigid furring channels 24” o.c. Gypsum board end joints located midway between continuous channels and attached to additional pieces of channel 60” long. Rigid furring channels applied at right angles to 12” deep parallel chord wood trusses 24” o.c. Wood trusses supporting 3/4” nominal interior plywood with exterior glue, T & G edges, applied at right angles to trusses. End joints staggered 48”. Consult the gypsum board manufacturer for truss details.

Fire Test: UL R4024, 00NK26545, UL Design L556; ULC Design M514

FC 5751

PABCO® GYPSUM WALLBOARD, WOOD FLOOR, WOOD TRUSSES, RIGID FURRING CHANNELS Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to 18” deep parallel chord wood trusses 24” o.c. Second layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to trusses. Second layer joints offset 24” from base layer joints. Third layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to trusses. Third layer joints offset 12” from second layer joints. Hat-shaped rigid furring channels 24” o.c. applied at right angles to trusses over third layer. Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to furring channels. Wood trusses supporting 3/4” T & G edge plywood floor applied at right angles to trusses. Ceiling provides two-hour fire resistance protection for wood framing.

FC 5520

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #56

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

FLOOR-CEILING WOOD FRAMED (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, WOOD FLOOR, WOOD JOISTS, RESILIENT CHANNELS

2 hr

NA

FC 5710

Base layer 5/8” PABCO® FLAME CURB® Super C type C gypsum wallboard applied at right angles to 2 x 10 wood joists 16” o.c. Resilient channel 24” o.c. applied at right angles to wood framing through base layer. Double channel installed at face layer end joints.

Base layer 5/8” PABCO® FLAME CURB® Super C type C gypsum wallboard applied at right angles to 2 x 10 wood joists 16” o.c. Resilient furring channels 24” o.c. applied at right angles to joists through base layer at each joist.

NA

FC 5724

Fire Test: UL R1319-114, UL Design L511

Face layer 5/8” PABCO® FLAME CURB® Super C type C gypsum wallboard applied at right angles to resilient furring channels. Wood joists supporting 15/32” plywood subfloor and 19/32” plywood finish floor applied at right angles to joists with joints staggered. Consult the gypsum board manufacturer for other flooring options.

PABCO® GYPSUM WALLBOARD, WOOD FLOOR, WOOD JOISTS, RESILIENT CHANNELS

2 hr

Fire & Sound Test Numbers

Fire Test: UL R2717-35, UL Design L505; ULC Design M503

Face layer 5/8” PABCO® FLAME CURB® Super C type C gypsum wallboard applied at right angles to resilient furring channels. Double channel installed at face layer end joints. Wood joists supporting 1” nominal T & G wood subfloor and 1” nominal wood finish floor or 19/32” plywood finished floor with long edges T & G and 15/32” interior plywood with exterior glue subfloor perpendicular to joists with joints staggered. PABCO® GYPSUM WALLBOARD, WOOD FLOOR, WOOD I-JOISTS, RIGID FURRING CHANNELS Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to 9-1/2” deep wood I-joists 24” o.c.

Fire Test: UL R4024, 00NK26545, UL Design L556; ULC Design M514

Second layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to I-joists. Second layer joints offset 24” from base layer joints.

2 hr

NA

FC 5750

Third layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to I-joists. Third layer joints offset 12” from second layer joints. Hat-shaped rigid furring channels 24” o.c. applied at right angles to I-joists over third layer. Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at rightangles to furring channels. Wood I-joists supporting 3/4” T & G edge plywood floor applied at right angles to I-joists. Ceiling provides two-hour fire resistance protection for wood framing.

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #57

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

ROOF CEILING - WOOD FRAMED

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

File No

Construction Detail

Description PABCO® GYPSUM WALLBOARD, WOOD ROOF TRUSSES, RESILIENT CHANNELS, GLASS OR MINERAL FIBER INSULATION, CEILING DAMPER

1 HR

NA

RC 2608

One layer 5/8” FLAME CURB® Super C type C gypsum wallboard applied at right angles to resilient furring channels 16” o.c. (12” o.c. when insulation is draped over channels). Gypsum board end joints attached with screws 8” o.c. to additional pieces of channel 60” long located 3” back on either side of end joint.

Fire & Sound Test Numbers Fire Test: UL R7094, 07NK11121, UL Design P549; WFCi 07002C/07048

Resilient channels applied at right angles to bottom chord of pitched wood trusses 24” o.c. Optional glass fiber or mineral fiber batt insulation secured to wood structural panels or applied directly over gypsum board. Trusses supporting 15/32” wood structural panels applied at right angles to trusses. Optional ceiling damper (refer to manufacturer for information on the type of damper). PABCO® GYPSUM WALLBOARD, WOOD TRUSSES

1 HR

NA

RC 2602

Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to wood roof trusses 24” o.c. Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to trusses. Joints offset 24” from base layer joints. Wood trusses supporting 1/2” wood structural panels applied at right angles to trusses. Appropriate roof covering.

Fire Test: FM FC 172; ITS

Ceiling provides one hour fire resistance protection for trusses. PABCO® GYPSUM WALLBOARD, RIGID FURRING CHANNELS WOOD JOISTS or WOOD I-JOISTS, ROOF COVERING Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to either 2 x 8 wood joists or 9-1/2” deep wood I-joists 24” o.c. Second layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to joists or I-joists. Second layer joints offset 24” from base layer joints.

2 HR

NA

RC 2750

Fire Test: UL R4024, 00NK26545, UL R4042, 03NK11206; UL Design L556; ULC Design M514

Third layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to joists or I-joists. Third layer joints offset 12” from second layer joints. Hat-shaped rigid furring channels 24” o.c. applied at right angles to joists or I-joists over third layer. Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to furring channels. Wood joists or I-joists supporting 3/4” T & G edge plywood applied at right angles to joists or I-joists. Appropriate roof covering. Ceiling provides two-hour fire-resistance protection for wood framing.

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #58

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

ROOF-CEILING Wood Framed (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA

File No

Construction Detail

Fire & Sound Test Numbers

Description PABCO® GYPSUM WALLBOARD, WOOD ROOF TRUSSES, RIGID FURRING CHANNELS Base layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to wood roof trusses 24” o.c.

Fire Test: UL R4024, 00NK26545, UL Design L556; ULC Design M514

Second layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to trusses. Second layer joints offset 24” from base layer joints.

2 HR

NA

RC 2751

Third layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to trusses. Third layer joints offset 12” from second layer joints. Hat-shaped rigid furring channels 24” o.c. applied at right angles to trusses over third layer. Face layer 5/8” FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied at right angles to furring channels. Wood trusses supporting 3/4” T & G edge wood structural panels applied at right angles to trusses. Appropriate roof covering. Ceiling provides two-hour fire-resistance protection for wood framing.

the

to

®

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #59

SJ 06-14-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

COLUMNS - Noncombustible

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

GA Rating Rating File No

Construction Detail Light Tubular Column

Description PABCO® GYPSUM WALLBOARD, STEEL STUDS

1 hr

NA

Base layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied without horizontal joints to 1-5/8” steel studs located at each corner of TS 4x4x0.188 tube steel column.

CM 1452

Fire & Sound Test Numbers Fire Test: UL NC505, 77NK1747; UL Design X528

Face layer 1/2” PABCO® FLAME CURB® type XXX gypsum wallboard applied without horizontal joints to studs. Metal cornerbead applied to all corners. Joint compound 1/16” thick applied over corner bead. PABCO® GYPSUM WALLBOARD, STEEL STUDS

1 hr

NA

One layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied without horizontal joints and parallel to 1-5/8” steel studs located at each corner of TS 8x8x0.250 tube steel column.

CM 1851

Fire Test: UL NC505, 77NK1747; UL Design X528

Steel cornerbead, 1-1/2” flanges, applied. Joint compound 1/16” thick applied over corner bead. PABCO® GYPSUM WALLBOARD, STEEL STUDS

1.5 hr

NA

Two layers of 1/2" PABCO® FLAME CURB® Super C type PG -C gypsum wallboard applied vertically to 1-5/8" steel studs and channels, furred from 4-1/2" min OD steel pipe column (min wall thickness 0.109” and min 5.1 lbs/ft weight). Channels tied to column with No. 18 SWG tie wire.

NA

Fire Test: UL X531

Steel cornerbead, 1-1/4” legs, applied. Joint compound 1/16” thick applied over corner beads, joints, and surfaces of wallboard. PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied without horizontal joints to 1-5/8” steel studs located at each corner of TS 4x4x0.188 tube steel column .

2 hr

NA

Fire Test: UL NC505, 77NK1747; UL NC505; UL Design X528

Second layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied without horizontal joints.

CM 2455

Face layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8” WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied without horizontal joints to studs. Metal corner bead applied to all corners. Joint compound 1/16” thick applied over corner bead

Column 10WF-49 PABCO® GYPSUM WALLBOARD, STEEL STUDS

1 hr

NA

CM 1001

One layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied without horizontal joints to 1-5/8” steel studs located at each corner of W10x49 column. Metal corner bead applied to all corners.

Fire Test: UL NC505, 77NK1747; UL Design X528

Joint compound 1/16” thick applied over corner bead.

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #60

SJ 06-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

COLUMNS -Noncombustible (continued) Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

STC

Rating Rating

GA File No

Construction Detail Column 10WF-49

Description PABCO® GYPSUM WALLBOARD, STEEL STUDS

2 hr

NA

Base layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied without horizontal joints to 1-5/8” steel studs located at each corner of W10x49 column.

CM 2017

Fire & Sound Test Numbers Fire Test: UL NC505, 77NK1747; UL Design X528

Face layer 1/2” PABCO® FLAME CURB® Super C type PG -C gypsum wallboard applied without horizontal joints to studs. Metal corner bead applied to all corners. Joint compound 1/16” thick applied over corner bead PABCO® GYPSUM WALLBOARD, STEEL STUDS Base layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied to 1-5/8” steel studs located at each corner of W10x49 column.

3 hr

NA

Second layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied to studs.

CM 3120

Fire Test: UL R2717-31, UL Design X509; UL R3501-36, UL Design X510; ULC Design Z502

Face layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied to studs. Metal corner bead applied at all corners. Base Layer and Second layer 5/8” PABCO® FLAME CURB® Super C Type C gypsum wallboard applied to 1-5/8” steel studs located at each corner of W10x49 column.

4 hr

NA

Fire Test: UL Design X501

Third layer and Face layer 5/8” PABCO® FLAME CURB® Super C Type C gypsum wallboard applied to 2" x 2" sheet metal angles placed at the corners of the second layer of wallboard.

NA

Metal corner bead applied at corners and covered with joint compound treatment.

Column 14WF-228 PABCO® GYPSUM WALLBOARD, STEEL STUDS

2 hr

NA

CM 2110

One layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard attached to 1-5/8” steel studs located at each corner of heavy steel W14x228 columns. 1-1/4” metal corner bead applied by crimping 6” o.c.

PABCO® GYPSUM WALLBOARD, STEEL STUDS

3 hr

NA

CM 3130

Base layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied to 1-5/8” steel studs located at corners of heavy steel W14x228 column.

Fire Test: UL R3501-58, UL Design X520; ULC Design X520

Fire Test: UL R3501-61, UL Design X513; ULC Design X513

Face layer 1/2” PABCO® FLAME CURB® type XXX, or 1/2” FLAME CURB® Super C gypsum wallboard applied to studs. 1” corner bead applied. PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #61

SJ 06-07-11/ Fire Rated Systems- PABCO® Gypsum

FIRE RATED SYSTEMS

a division of PABCO® building products, LLC

BEAMS & GIRDERS - Noncombustible

"Quality to the Core"

R

Please refer to the referenced test report for construction details. Assemblies listed are examples of systems where PABCO Gypsum board products have been approved for use. Additional assemblies are available. For more information please contact PABCO Gypsum Technical Services at 866-282-9298, or email to [email protected]. www.pabcogypsum.com

FIRE

Rating

GA File No

Construction Detail

Fire & Sound Test Numbers

Description

Fire Test: UL R1319-133; Based on UL R3660-7 & -8; UL Design L524

PABCO® GYPSUM WALLBOARD, STEEL FRAME Base layer 1/2” PABCO® FLAME CURB® Super C type PC-C gypsum wallboard applied to beam cage.

1 hr

BM 1137

Face layer 1/2” PABCO® FLAME CURB® Super C type PC-C gypsum wallboard applied to beam cage. Joints offset from base layer joints. Beam cage fabricated from No. 24 gage 7/8” x 1-3/8” steel angles screw attached to steel joists at beam top flange and No. 25 gage 2-1/2” steel runners hooked over beam lower flange and supporting 1-5/8” steel studs 24” o.c. Minimum beam size W8x15. (One hour unrestrained beam.)

Fire Test: UL R4024-5, UL Design N501; ULC Design O501

PABCO® GYPSUM WALLBOARD, STEEL FRAME Base layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied to beam cage.

2 hr

BM 2120

Face layer 5/8” PABCO® FLAME CURB® type X gypsum wallboard, 5/8”WATER CURB® type X backing board, or 5/8” PABCO® type X gypsum sheathing applied to beam cage. Beam cage fabricated from horizontally installed steel angles (25 gage steel having 1” and 2” legs). “U” shaped brackets formed of 25 gage “U” shaped steel channels (1-11/16” wide with 1” legs) 24” o.c. suspended from upper angles. Minimum beam size W8x24. (Two hour restrained or unrestrained beam.)

the

to

®

PABCO®, FLAME CURB®, WATER CURB®, PABCORE®, MOLD CURB®, ABUSE CURB™, “Quality to the Core”®, are registered trademarks of Pacific Coast Building Products and licensed to PABCO® Gypsum

Page #62

SJ 06-07-11/ Fire Rated Systems- PABCO® Gypsum

Quality Matters.

At PABCO® Gypsum, quality is a serious part of our business; a core fundamental value. It’s what sets us apart from our competitors, a core key-success-factor, a commitment to you. It’s why customers ask for our products, and why they come back year after year. PABCO® Gypsum, Commitment to the Core™

Quality to the Core

®

the

to

®

MGM CityCenter, Las Vegas, NV: utilized approximately 18 mil sf of PABCO® Gypsum wallboard

Technical Service • Literature • Samples

866-282-9298

[email protected] www.PabcoGypsum.com

Limited Warranty: PABCO® Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE GYPSUM BOARD APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE GYPSUM BOARD PRIOR TO SUCH VISIBLY DEFECTIVE GYPSUM BOARD BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO® BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. PABCO® BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES – WHETHER EXPRESS, IMPLIED, OR STATUTORY – INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE. If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO® Building Products, LLC, in writing, and within 60 days of discovery, PABCO® Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY. IN NO EVENT SHALL PABCO® BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory.

a division of PABCO® building products, LLC PABCO® Gypsum Construction Guide - Fire & Sound Rated Systems Copyright © 2009, 2011 • 2nd Edition PABCO® Gypsum • a division of PABCO® Building Products, LLC PO Box 417094 • Rancho Cordova • CA • 95741 www.pabcogypsum.com; 7-2011; 3M

Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO® Gypsum: PABCO®, PABCORE®, FLAME CURB®, WATER CURB®, MOLD CURB®, Quality to the Core®, ABUSE CURB™. Notice: Products described herein may not be available in all geographic markets. Consult your PABCO® Gypsum sales representative for information or call our Technical Services. Current updated information is available on our website: www.pabcogypsum.com. The information in this publication may change without notice.