Compact Design Hydraulic Cylinder 160S-1 Compact Design Hydraulic Cylinder

160S-1

21

16MPa Compact Design Hydraulic Cylinder

16MPa Compact Design Hydraulic Cylinder with Steel Body ●

Operates up to 10 million times at maximum 16 MPa.

●

Abrasion resistant seal is standard. Standard type cylinders are fully operable at ambient temperatures of up to 120°C.

●

Introducing special copper alloy for vital hydraulic cylinder.

●

Sliding type switches allow flexible switch placement.

Standard Specifications

Compact Design Hydraulic Cylinder

Types

Terminologies (Referred to the revised JIS B8367)

Specifications of General Purpose

Cutting Fluid Proof Types

Nominal pressure

16 MPa

Maximum operating pressure

16 MPa

Proof test pressure

24MPa

Minimum working pressure

0.3 MPa

Operationg speed range Temperature range (Ambient temperature and oil temperature)

Pressure to be used to express a cylinder model’s typical performance. This pressure value does not always match the actual operating pressure (rated pressure) at which the cylinder’s performance is ensured under the specified conditions.

Maximum operating pressure The cylinder’s maximum internal pressure available. This pressure differs from the relief valve’s set pressure. Pressures that are higher than the relief valve’s set pressure, such as surge pressure during valve changing, are applied to the inside of the cylinder.

8 - 100 mm/s Standard type ..................................... -10 - +120°C Switch set AX · AZ type ............... -10 - +70°C (Note) WR · WS type ............ -10 - +60°C

Proof test pressure Proof test pressure is defined what could keep performance of cylinder through test pressure and nominal pressure.

(free of freeze)

Structure of cushioning

None

Adaptable working oil

Petroleum-based fluid (For other working oil, refer to the table of working oil adaptability)

Minimum working pressure

Tolerance of thread

JIS 6 g/6H (JIS grade 2 or equivalence)

Tolerance of stroke

0 to 0.8mm

Mounting type

SD, ST, LA, LD, FA, FB

Rod end threads Suitable switches for switch set

Nominal pressure

The minimum pressure that the cylinder placed horizontally without a load can work. Notes) ● This cylinder is not equipped with an air bleeder. ● Since

lateral load (eccentric load) cannot be applied to the piston rod, carefully ad-

SD, LD, FA, FB

just it after rod end attachment.

Female and male threads 160S-1R:

AX · AZ types WR · WS types

● The

working temperature range depends on the material of packings. For details, refer to the selection materials in the be-

160SW-1R: WR · WS types

ginning of this catalogue. ● If

the piston touches the cylinder end at the stroke end, decelerate the cylinder to a speed lower than the minimum operat-

Note) The switch ‘AX125’ and ‘AZ125’ are newly developed for high temperature circumstance up to 100˚C.

ing speed.

Cutting fluid proof models ● These models can be used in environments where the machine tool cutting oil (coolant) can be splashed. ● Sealing materials suitable for each cutting oil are as shown

Allowable Seal Material (Hydrogenated Nitrile Rubber) and Cutting Oil Non-water Soluble Cutting Oil Water Soluble Cutting Oil Type 1

Type 2

K

×

in the right side table: K: All wable

×: Unallowable

K

160S-1

16MPa Compact Design Hydraulic Cylinder

Lines

22

Unit: mm

Structure

Type

Mounting Type ø20

ø25

ø32

ø40

ø50

ø63

ø80

ø100

ø125

SD (ST) Standard type

General purpose type

160S-1 Double Acting Single Rod

LD, FA, FB SD (ST) Switch set

160S-1R

SD Standard type

Double Acting Double Rod

160S-1D

160SW-1 Switch set

160SW-1R Standard type

Double Acting Double Rod

160SW-1D Switch set

160SW-1RD

SD LD, FA SD

Compact Design Hydraulic Cylinder

Standard type

Double Acting Single Rod

LA LD, FA

Switch set

Cutting fluid proof type

LA LD, FA, FB

160S-1RD

Notes)

LA

LD, FA, FB SD LD, FA, FB SD LD, FA SD LD, FA

●

Switches can’t be mounted on Standard type. You are requested to select “Switch set” type when you would like to use switches. ● The ST mounting type is a made-to-order product.

Standard type

Switch set Basic type (SD)

160SW-1R

Basic type

160SW-1RD

Foot type 160S-1R

Double acting single-rod (160S-1, 160SW-1)

Double acting double-rod (160S-1D, 160SW-1D)

Double acting single-rod (160S-1R, 160SW-1R)

● Cylinder dimensions are all the same for both general purpose and cutting fluid proof types.

160S-1RD

Double acting double-rod (160S-1RD, 160SW-1RD)

160S-1

16MPa Compact Design Hydraulic Cylinder

!

Th

Ai rv en t

ty

C

yl C

St ro ke 6 re ad Po rt ty sp pe ec 7 ifi ca tio Sw n8 itc h sy m bo Sw l9 itc hq ua nti ty ! 0 Lo ck nu t! 1

pe 5

e4 or

on

rb

hi

de in

nt ou

us

er

in g

m at ck in g Pa

ty pe 3

ia l2

s1 rie Se

2

■ Semi-standard components

Dotted lines for types and symbols are not written when unnecessary.

General purpose type

M

23

● Standard type

160S-1

6

SD

40

N

50

T

G

● Switch set

160S-1R

6

SD

40

N

50

T

G

AF

2

– L

–

V

– L

–

V

Standard type

None Without air vent (Standard) With air vent (Made-toV

160S-1 : Double acting single-rod 160S-1D : Double acting double-rod

order:bore 32mm to 125mm)

Switch set 160S-1R : Double acting single-rod 160S-1RD : Double acting double-rod

with one lock nut Note) Available only for male thread type Additional order is required when 2 or more lock nuts are necessary.

6 Hydrogenated nitrile rubber (standard) 3 Fluoric rubber (semi-standard)

Switch quantity (1 or 2)

Compact Design Hydraulic Cylinder

Note) The seal of bore size 20mm & 25mm is only Nitrile rubber for high temperature.

SD ST LA LD FA FB

Switch symbol Note) Select applicable switches out of the Switch List. Notes on order for switch sets ● If a switch is unnecessary, enter the switch symbol o and the switch quantity !0 of 0. ● When ordering a switch set, switches are not mounted to cylinders at delivery.

SD type, basic type

Thread holes mounting LA type, foot type Foot type Head flange mounting Cap flange mounting Note) LD,FA mounting style cylinders consist of SD cylinder and each bracket. In this case, SD cylinder’s

None Rc thread G thread G Note) G screw is only for SD Mounting.

Standard type SD : ø20 - ø125 ST : ø32 - ø80

– Female thread (no symbol for the standard type) T Male thread

LD, FA, FB : ø20 - ø80 LA : ø32 - ø63 Switch set SD, ST, LD, FA, FB : ø32 - ø80 LA : ø32 - ø63

Note) Double-rod and male thread means both sides are male thread as standard. Cylinder stroke (mm) Without cushion

Cutting fluid proof type ● Standard type

R160SW-1

6 SD

40

N

50

T

G

● Switch set

160SW-1R

6 SD

40

N

50

T

G

Standard type 160SW-1 : Double acting single-rod 160SW-1D : Double acting double-rod Switch set 160SW-1R : Double-acting single rod 160SW-1RD : Double-acting double rod Note) For explanations for models other than the above, refer to the general purpose type models. ST, LA is not available.

5

– L

– V

2 – L

– V

5

WR525 (cord extended from the rear, with 5 m cord)

8

WR535 (cord extended from the top, with 5 m cord)

5F WR525F (cord extended from the rear, with 5 m cord/flex tube attached) Cylinder bore (mm) ø32 - ø100 8F WR535F (cord extended from the top, with 5 m cord/flex tube attached) Note) 100mm bore is not available for RA AX205W (cord extended from the rear, with 5 m cord) LD, FA, FB. RB AZ205W (cord extended from the top, with 5 m cord)

Hydrogenated nitrile rubber

2

WS235 (cord extended from the rear, with 5 m cord)

1

WS245 (cord extended from the top, with 5 m cord)

2F WS235F (cord extended from the rear, with 5 m cord/flex tube attached) 1F WS245F (cord extended from the top, with 5 m cord/flex tube attached)

160S-1

16MPa Compact Design Hydraulic Cylinder

24

Switch List Kind Switch Symbol Load Voltage Range Load Current Range

Maximum Open/ Close Capacity

Protective Circuit Indicating Lamp

AF AX101 AG AX105 AH AX111

None DC:5 - 30 V DC:5 - 40mA AC:5 - 120 V AC:5 - 20mA

DC:1.5W AC:2VA

AJ AX115 AE AX125

Contact

DC:30V or less DC:40mA or less AC:120V or less AC:20mA or less

None

AK AX11A

AC:5 - 120 V

5 - 20mA

2VA

AL AX11B

DC:5 - 30 V

5 - 40mA

1.5W

5

DC:5 - 50 V DC:3 - 40mA AC:5 - 120 V AC:3 - 20mA

WR525

5F WR525F

Present

Present

DC:1.5W AC:2VA

None

AP AZ101 AR AZ105 AS AZ111

None DC:5 - 30 V DC:5 - 40mA AC:5 - 120 V AC:5 - 20mA

DC : 1.5W AC : 2VA

AT AZ115 AN AZ125

None

AU AZ11A

AC:5 - 120 V

5 - 20mA

2VA

AW AZ11B

DC:5 - 30 V

5 - 40mA

1.5W

8

WR535

8F WR535F

Present

DC:30V or less DC:40mA or less AC:120V or less AC:20mA or less

DC:5 - 50 V DC:3 - 40mA AC:5 - 120 V AC:3 - 20mA

Present

DC : 1.5W AC : 2VA

None

BE AX201 BF AX205

5 - 40mA

–

Present

DC:10 - 30 V

6 - 20mA

–

Present

CF AX215 No Contact

2

WS235-1

2F WS235-1F BM AZ201 BN AZ205 CM AZ211

DC:5 - 30 V

CN AZ215

5 - 40mA

–

Present

Cutting fluid RA AX205W proof type RB AZ205W No Contact

1

WS245-1

1F WS245-1F

DC:10 - 30 V

6 - 20mA

–

Present

5 - 40mA

–

Present

1.5m LED (Red light lights 0.3 mm2, 2-core, up during ON) outer dia. ø4 mm rear wiring None LED (Red light lights up during ON) LED (Red light lights up during ON)

(

)

5m 0.5m

0.3 mm2, 2-core, outer dia. ø4 mm rear wiring

5m

0.5m 5m 1.5m

None LED (Red light lights up during ON) LED (Red light lights up during ON) LED (Red light lights up during ON) LED (2-lamp type in red/green) LED (2-lamp type in red/green) LED (Red light lights up during ON) LED (2-lamp type in red/green) LED (Red light lights up during ON) LED (2-lamp type in red/green)

Small relay, programmable controller

5m 1.5m 5m 5m

4-pin connector type, upper wiring

0.5m

0.3 mm2, 2-core, outer dia. ø4 mm upper wiring

5m

0.5m 5m 1.5m

5m 0.3 mm2, 2-core, 1.5m outer dia. ø4 mm 5m rear wiring 5m 5m 1.5m 0.3 mm2, 2-core, outer dia. ø4 mm upper wiring

5m 1.5m 5m

0.3 mm2, 2-core, outer dia. ø4 mm rear wiring 0.3 mm2, 2-core, outer dia. ø4 mm upper wiring

5m

Small relay, programmable controller

5m 0.3 mm2, 2-core, 5m outer dia. ø4 mm 5m upper wiring 0.3 mm2, 2-core, 1.5m outer dia. ø4 mm 5m rear wiring

LED 4-pin connector type, 0.5m rear wiring (2-lamp type in 0.3 mm2, 2-core, 1.5m red/green) outer dia. ø4 mm 5m upper wiring 4-pin connector type, upper wiring

CY AZ21BCE

Notes)

5m

4-pin connector type, rear wiring

LED (Red light lights 0.3 mm2, 2-core, up during ON) outer dia. ø4 mm upper wiring

CT AX211CE CU AX215CE No Contact CV AX21BCE CE DC:5 - 30 V coformed CW AZ211CE CX AZ215CE

5m 1.5m

0.5m

●

For the switches without a protective circuit, be sure to provide the protective circuit (SK-100) with load devices when using induction load devices (relay, etc.). ● For the handling of switches, be sure to refer to the switch specifications in the end of this catalogue. ● The WR and WS type switches are cutting fluid proof type. ● We recommend AND UNIT (AU series) for multiple switches connected in series. ●

● General purpose type AX type (cord rear wiring)

● Cutting fluid proof type WR · WS type switch ● Cord

rear wiring

WR525 WS235-1 AZ type (cord upper wiring) ● Cord

For the switch symbol o, pay attention to the points below when ordering the cutting fluid proof type switches, WR and WS types.

5 8 2 1

WR525 WR535 WS235-1 WS245-1

5F 8F 2F 1F

WR525F The flex tube (F-05: 4.8 m) is attached to WR535F the switch and straight box connector WS235-1F (F-SB). WS245-1F

The switch and straight box connector (F-SB) are combined [the flex tube (F-05: 4.8 m) is required].

upper wiring

WR535 WS245-1

Switch body

Straight box connector: F-SB Flex tube: F-05

Compact Design Hydraulic Cylinder

DC:5 - 30 V

CE AX211

Applicable Wiring Method Cord Length Load Device

25

160S-1

16MPa Compact Design Hydraulic Cylinder

Standard stroke fabrication range (Single-rod)

Compact Design Hydraulic Cylinder

Structure

Type

Mounting Type

Bore

5

10

15

20

25

30

Cylinder Stroke (mm) 35 40 45 50 60

70

80

90 100

Male Thread Type

f20 f25 f32 f40 Basic type f50 (SD) f63 f80 f100 f125 Standard f20 Flange type f25 type 160S-1 f32 (FA, FB) f40 General f50 Foot type purpose f63 (LD) type f80 f32 f40 Foot type (LA) f50 f63 Basic type f32 (SD) f40 Flange type f50 (FA, FB) f63 Foot type Switch set (LD) f80 160S-1R f32 Foot type f40 (LA) f50 f63 f32 f40 Basic type f50 (SD) f63 Standard f80 type f100 160SW-1 f32 Flange Cutting type f40 fluid (FA, FB) f50 proof type Foot type f63 (LD) f80 Basic type f32 (SD) f40 Switch set Flange type f50 (FA, FB) 160SW-1R f63 Foot type (LD) f80 : Standard manufacturing range,

: Range available for manufacturing for order

Available bore range at ST mounting. (Single-rod only/Made-to-order) Structure

General purpose type

Type

Mounting Type

Standard type 160S-1

Thread holes mounting (ST)

Switch set 160S-1R

Thread holes mounting (ST)

Bore f32 f40 f50 f63 f80 f32 f40 f50 f63 f80

: Range available for manufacturing for order

110

120

130

140

Cylinder Stroke (mm) 150 160 170

180

190

200

Male Thread Type

16MPa Compact Design Hydraulic Cylinder

160S-1

26

Standard stroke fabrication range (Double-rod) Structure

Type

Mounting Type

Basic type (SD)

Standard type 160S-1D General purpose type

Flange type (FA) Foot type (LD)

Foot type (LA)

Basic type (SD)

Cutting fluid proof type

Standard type 160SW-1D

Flange type (FA) Foot type (LD)

Basic type (SD) Switch set Flange type (FA) 160SW-1RD Foot type (LD) : Standard manufacturing range,

5

10

15

20

25

30

Cylinder Stroke (mm) 35 40 45 50 60

f20 f25 f32 f40 f50 f63 f80 f100 f125 f20 f25 f32 f40 f50 f63 f80 f32 f40 f50 f63 f32 f40 f50 f63 f80 f32 f40 f50 f63 f80 f100 f32 f40 f50 f63 f80 f32 f40 f50 f63 f80 : Range available for manufacturing for order

70

80

Male Thread

90 100 Type

Compact Design Hydraulic Cylinder

Basic type (SD) Switch set Flange type (FA) 160S-1RD Foot type (LD)

Bore

27

160S-1

16MPa Compact Design Hydraulic Cylinder

Adaptability of Working Oil to Packing Material

Cutting Fluid Proof Type/Adaptability of Cutting Fluid to Packing Material

Adaptable Working Oil

Packing Material

Petroleum- Water-glycol Phosphoric W/O Water in based fulid fulid ester fluid oil fluid

cFluoric rubber

×

K

K

K

K

Type 1

Type 2

K

×

nHydrogenated nitrile rubber

×

nHydrogenated nitrile rubber

Non-water Soluble Cutting Oil

Packing Material

O/W Oil in water fluid

Water Soluble Cutting Oil K

K : applicable ✕: inapplicable

Notes) 1. The and K - marked items are applicable, while the ✕ - marked items are inapplicable. 2. The - marked items are the recommended packing materials in case of giving the first priority to abrasion resistance.

Specification of Air Vent (Option) • The air vents are laid on the port surface and located symmetrical position to the port.

How to order G screw piping port (only for SD type)

Set screw (Exclusive use for air vent)

• Please specify the model as following. ex. 160S-1 6SD63N30 – G G screw piping port

2-Air vent

Steel ball 2-Port (Figure)

(Structure): Single-rod, Double-rod SD/LD/FA/FB type

Note) In some bores, the apparent dimensions are changed from their standard when you specify G screw. Please refer to the detailed dimension table in following pages.

Location of air vent on the same surface as piping port (Option)

Compact Design Hydraulic Cylinder

Dimension Table

How to order only lock nut d

C

h

B

Bore

Part Model

d

B

C

h

ø20

LNH-10F-H

M10✕1.25

17

19.6

6

ø25

LNH-12F-H

M12✕1.25

19

21.9

7

ø32

LNH-16F-H

M16✕1.5

22

25.4

10

ø40

LNH-20F-H

M20✕1.5

27

31.2

12

ø50

LNH-24F-H

M24✕1.5

32

37.0

14

ø63

LNH-30F-H

M30✕1.5

41

47.3

17

ø80

LNH-39F-H

M39✕1.5

55

68.5

20

ø100

LNH-48F-H

M48✕1.5

70

80.8

26

ø125

LNH-64F-H

M64✕2

90

104

35

Switch Mounting Minimum Possible Stroke With A Switch

With Two Switches

Bore AX and AZ types

WR type

WS type

AX and AZ types

WR type

WS type

5

5

10

10✽

10

20

ø32 ø40 ø50 ø63 ø80 Note) • When attaching two switches of the WR or WS type, they cannot be attached to the same surface. (WR and WS type switches are not available for LA mounting.) ✽If you would like to mount two switches to 10mm stroke cylinder, please.

Operating Ranges and Differences Contact Bore

AX and AZ types

No Contact WR type

AX and AZ types

AX205W･AZ205W

WS type

Operating range Difference Operating range Difference Operating range Difference Operating range Difference Operating range Difference ø32 ø40 15 - 22 ø50

10 - 17

2 or less

10 - 17

2 or less

4-8

1 or less

2 or less

ø63 ø80

19 - 25

15 - 24

1 or less

160S-1

16MPa Compact Design Hydraulic Cylinder

Weight Table/General Purpose and Cutting Fluid Proof Types Basic type (SD)

28

Unit: kg Mounting accessories Rod end attachment additional weight additional weight

Foot type (LA)

Separate Bore Double Acting Single-rod Double Acting Double-rod Double Acting Single-rod Double Acting Double-rod flange Foot type Flange type (mm) joint Basic Added weight Basic Added weight Basic Added weight Basic Added weight (LD) (FA, FB) for each for each for each for each (M type weight stroke of 1 mm weight stroke of 1 mm weight stroke of 1 mm weight stroke of 1 mm joint)

Added male thread weight

ø20

0.6

0.013

0.7

0.014

–

–

–

–

0.25

0.46

0.2

0.015

ø25

0.8

0.016

1.0

0.017

–

–

–

–

0.30

0.58

0.3

0.026

ø32

1.4

0.025

1.6

0.024

1.4

0.027

1.9

0.028

0.62

1.09

0.3

0.057

ø40

1.8

0.030

2.1

0.032

1.8

0.034

2.4

0.036

1.16

1.42

0.4

0.114

ø50

2.5

0.037

2.7

0.036

2.6

0.044

3.3

0.048

1.60

2.43

0.6

0.201

ø63

3.8

0.047

4.1

0.041

4.1

0.062

5.0

0.068

2.02

3.30

0.8

0.435

ø80

6.6

0.067

7.6

0.083

–

–

–

–

3.77

5.86

1.4

0.798

ø100

12.5

0.102

14.9

0.121

–

–

–

–

–

–

3.0

–

ø125

21.5

0.152

29

0.222

–

–

–

–

–

–

5.3

–

Weight Table/Switch set

Unit: kg

Basic type (SD)

Foot type (LA)

Double Acting Double-rod

Double Acting Single-rod

Rod end attachment additional weight

Separate flange joint (M type joint)

Added male thread weight

Flange type

Foot type

(FA, FB)

(LD)

0.022

0.62

1.09

0.3

0.057

1.6

0.028

1.16

1.42

0.4

0.114

0.041

2.3

0.036

1.60

2.43

0.6

0.201

3.7

0.057

3.6

0.049

2.02

3.30

0.8

0.435

7.2

0.084

–

–

3.77

5.86

1.4

0.798

Basic weight

Added weight for each stroke of 1 mm

Basic weight

Added weight for each stroke of 1 mm

Basic weight

Added weight for each stroke of 1 mm

ø32

1.2

0.022

1.3

0.024

1.2

ø40

1.6

0.028

1.7

0.031

ø50

2.2

0.036

2.4

ø63

3.3

0.049

ø80

6.2

0.071

Switch Added Weight Table

Unit: kg

AX · AZ Type WR · WS Type Cord length 1.5 m

Cord length 5 m

Connector type

0.05

0.13

0.04

0.50

Formula Cylinder weight (kg) = Basic weight + (Cylinder stroke (mm) ✕ Added weight for each stroke of 1 mm) + (Added switch weight ✕ Number of switches) Calculation example 160S-1R: Bore of ø40, cylinder stroke of 50 mm, AZ101 (cord length of 1.5 m), with two switches 1.6 + (50 ✕ 0.028) + (0.05 ✕ 2) = 3.10 kg

Piston Pressurized Area Table Bore (mm)

Rod Diameter (mm)

Unit: mm2

Double Acting Single-rod Push side

Pull side

Double Acting Double-rod Push side

Pull side

ø20

ø12

314

201

201

ø25

ø14

491

337

337

ø32

ø18

804

550

550

ø40

ø22

1257

876

876

ø50

ø28

1963

1348

1348

ø63

ø36

3117

2100

2100

ø80

ø45

5027

3436

3436

ø100

ø56

7854

5391

5391

ø125

ø70

12272

8424

8424

Formula

F = A·P·β(N)

F: Cylinder force (N) A: Piston pressurized area (mm2) P: Applied pressure (MPa) β: Load rate Calculation example Double acting single-rod, bore of ø40, applied pressure of 16 MPa, load rate of 0.8 Push side cylinder force (N) = 1257 ✕ 16 ✕ 0.8 = 16090 (N) Pull side cylinder force (N) = 876 ✕ 16 ✕ 0.8 = 11213 (N)

Compact Design Hydraulic Cylinder

Double Acting Single-rod

Bore (mm)

Mounting accessories additional weight

29

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

CAD/DATA is available.

160S-1/THS16 Bore

SD

General purpose type 160S-1

6 SD Bore N Stroke

T

(ø20 - ø125)

Cutting fluid proof type 160SW-1 6 SD Bore N Stroke

T

(ø32 - ø100) None : Female thread T : Male thread

• Bore ø20, ø25 Less than 15 strokes EE

• Male thread A KK

Over 15 strokes EE

WF C

MM

Width across flats D Y

Compact Design Hydraulic Cylinder

4-FB holes 2✕4-Counter hole diameter FG, Depth BT

PJ+ Stroke PL

Y

PL

EE

KK depth KL

MM

MM

Width across flats D

Width across flats D

C TV

PJ+ Stroke

LL+Stroke

WF

C

WF

LF+Stroke

E

LL+Stroke LF+Stroke

• Bore ø32 - ø125 • Male thread A

G screw port DE

FF

KK

C

N N

MM

AE

EE

WF

Width across flats D

4-FB holes 2✕4-Counter hole diameter FG, Depth BT

Y

PJ+Stroke

KK depth KL

MM

Width across flats D C TV E

WF

LL+Stroke LF+Stroke

PL

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

30

Dimension Table Symbol AE

A

BT

C

DE

D

E

EE

FB

FF

KK

FG

KL

Female thread Male thread

Bore

ø20 15(25)

–

5.4

6

10

–

44

Rc1/8

ø5.5

–

ø9.5

M8✕1.25

M10✕1.25

10

ø25 18(30)

–

5.4

6

12

–

50

Rc1/8

ø5.5

–

ø9.5

M10✕1.5

M12✕1.25

12

ø32 25(40)

8

6.5

7

14

ø17.2

62

Rc1/4

ø6.6

G1/8

ø11

M12✕1.75

M16✕1.5

15

ø40 30(45)

8

8.6

7

19

ø17.2

70

Rc1/4

ø9

G1/8

ø14

M16✕2

M20✕1.5

20

ø50 35(50)

12

10.8

8

24

ø21.5

80

Rc1/4

ø11

G1/4

ø17.5

M20✕2.5

M24✕1.5

24

ø63 45(60)

12

13

9

30

ø21.5

94

Rc1/4

ø14

G1/4

ø20

M27✕3

M30✕1.5

33

ø80 60(80)

12

15.2

14

41

ø21.5

114

Rc3/8

ø16

G1/4

ø23

M30✕3.5

M39✕1.5

36

ø29

M39✕4

M48✕1.5

45

ø35

M48✕5

M64✕2

58

12

ø100 75(95)

14

ø125 95(125)

19.5 23.5

22 25

Symbol LF

LL

ø25.5

50

140

ø30

65

172

N

MM

Rc3/8 Rc1/2

ø20 ø24

PJ

G3/8 G1/2 PL

TV

Rc thread G thread

Rc thread G thread Rc thread G thread Rc thread G thread

Bore

Y

WF

–

10.5

–

12

–

30

8

20.5

–

–

12

–

36

8

20.5

–

51

43

ø12

ø25

53

45

ø14

–

–

12.5

ø32

64

54

ø18

10

10

14

14

12

12

47

10

28

28

ø40

65

55

ø22

10

10

16

16

12

12

52

10

27

27

ø50

71

60

ø28

10

14

19

13.5

13

18.5

58

11

28

28

ø63

80

67

ø36

10

16

24

20

13

17

69

13

30

30

ø80

95

78

ø45

15

19

25

24

18

18

86

17

35

36

ø100

122

96

ø56

15

18

26

26

28

28

106

26

42

42

ø125

135

105

ø70

25

25

29

29

30

30

132

30

46

46

Notes) • • • •

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

ø20

–

31

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1 ST

General purpose type 160S-1 6 ST Bore N Stroke

(ø32 - ø80/Made-to-order)

T

None : Female thread T : Male thread over 101 strokes (110, 120, 130, 140, 150, 160, 170, 180, 190, 200)

• Bore ø32 - ø80 • Male thread A

EE

WF C

KK

N

Compact Design Hydraulic Cylinder

MM

N

Width across flats D Y

2✕4-TT, Deapth BT

PJ

KK depth KL

MM

Width across flats D TV

C WF

E

LL

Y

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

32

Dimension Table Symbol

KK D

A

BT

C

E

EE

KL

MM

N

TT

ø32

25(40)

15

7

14

62

Rc1/4

M12✕1.75

M16✕1.5

15

ø18

10

M6✕1

ø40

30(45)

20

7

19

70

Rc1/4

M16✕2

M20✕1.5

20

ø22

10

ø50

35(50)

25

8

24

80

Rc1/4

M20✕2.5

M24✕1.5

24

ø28

ø63

45(60)

30

9

30

94

Rc1/4

M27✕3

M30✕1.5

33

ø80

60(80)

35

14

41

114

Rc3/8

M30✕3.5

M39✕1.5

36

Symbol Stroke

TV

WF

Y

47

10

28

M8✕1.25

52

10

27

10

M10✕1.5

58

11

28

ø36

10

M12✕1.75

69

13

30

ø45

15

M16✕2

86

17

35

Female thread Male thread

Bore

LL

PJ

110

120

130

140

150

160

170

180

190

200

110

120

130

140

150

160

170

180

190

200

ø32

192

202

212

222

232

242

252

262

272

282

136

146

156

166

176

186

196

206

216

226

ø40

192

202

212

222

232

242

252

262

272

282

138

148

158

168

178

188

198

208

218

228

ø50

195

205

215

225

235

245

255

265

275

285

139

149

159

169

179

189

199

209

219

229

ø63

202

212

222

232

242

252

262

272

282

292

142

152

162

172

182

192

202

212

222

232

ø80

215

225

235

245

255

265

275

285

295

305

145

155

165

175

185

195

205

215

225

235

Bore

Compact Design Hydraulic Cylinder

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

33

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

160S-1/THS16 Bore

LA

General purpose type 160S-1 6 LA Bore N Stroke

T

CAD/DATA is available.

(ø32 - ø63) None : Female thread T : Male thread

• Bore ø32 - ø63

4-GB holes 4-Counter hole diameter FG, Depth BT

• Male thread A

SG+Stroke SW

SY

2-EE

WF C

KK

N

MM

N

Compact Design Hydraulic Cylinder

Width across flats D

EA TS

EB

Y

PJ+ Stroke

PL

KK depth KL

MM LH

C TX

Width across flats D T

WF

TW

TZ+ Stroke

LL+Stroke LF+Stroke

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

34

Dimension Table Symbol C

BT

A

D

EA

EB

EE

KK

GB

FG

Bore

Female thread

Male thread

KL

LF

LH

ø32

25(40)

8.6

7

14

70

56

Rc1/4

ø14

ø9

M12✕1.75

M16✕1.5

15

64

25±0.06

ø40

30(45)

10.8

7

19

80

64

Rc1/4

ø17.5

ø11

M16✕2

M20✕1.5

20

65

29±0.06

ø50

35(50)

13

8

24

94

74

Rc1/4

ø20

ø14

M20✕2.5

M24✕1.5

24

71

34±0.06

ø63

45(60)

15.2

9

30

114

89

Rc1/4

ø23

ø16

M27✕3

M30✕1.5

33

80

42±0.06

LL

MM

N

PJ

PL

SG

SW

SY

T

TS

TW

TX

TZ

WF

Y

ø32

54

ø18

10

14

12

24

10

20

63

56

12

28

14

10

28

ø40

55

ø22

10

16

12

23

12

20

70

62

12

28

15

10

27

ø50

60

ø28

10

19

13

27

13

20

80

74

14

29

17

11

28

ø63

67

ø36

10

24

13

32

15

20

100

90

16

31

20

13

30

Symbol Bore

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

When using a parallel key:

b1

Parallel key attached to the cylinder r1

t1

r1

When not using a parallel key: Pulling stopper

Use the same dimensions for the stopper as the attached parallel key.

Dimension Table Key’s Nominal Dimensions b✕h✕1

b1

t1

ø32

12✕8✕63 (Both rounded)

0 12 –0.043

5 +0.2 0

ø40

12✕8✕70 (Both rounded)

0 12 –0.043

5 +0.2 0

ø50

14✕9✕80 (Both rounded)

0 14 –0.043

5.5 +0.2 0

ø63

16✕10✕100 (Both rounded)

0 16 –0.043

6 +0.2 0

Bore

Pushing stopper

Key Way Dimensions

r1

0.25 - 0.40

• When using the foot type, use the attached parallel key to install the cylinder, referring to the “Recommended Key Way Dimensions.” • When not using the parallel key, attach the stoppers to the cylinder’s front and rear sides toward its stroke direction. If the cylinder is used without using the key or stoppers, a large force is applied to the cylinder’s mounting bolts, possibly resulting in the fracturing of the bolts.

Compact Design Hydraulic Cylinder

Recommended Key Way Dimensions

35

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

160S-1/THS16 Bore General purpose type 160S-1

LD

6 LD Bore N Stroke

T

(ø20 - ø80)

Cutting fluid proof type 160SW-1 6 LD Bore N Stroke

T

(ø32 - ø80)

CAD/DATA is available.

None : Female thread T : Male thread

• Bore ø20, ø25

• Male thread

• Less than 15 strokes

• Over 15 strokes

EE A KK

EE

W C

MM Width across flats D

FP KK depth KL

E

PJ+ Stroke

FP

PK

LF+Stroke

PJ+ Stroke

PK

LF+Stroke

Compact Design Hydraulic Cylinder

EE

MM

MM

EH LH

Width across flats D

ST

C W SU

TS

4-SB

Width across flats D

US

SU

LL+Stroke

XS

SS+Stroke

C W SU

SY

XS

SY

SS+Stroke

ZB+Stroke

ZB+Stroke

• Bore ø32 - ø80

EE

• Male thread A

SU

LL+Stroke

W C

KK

N MM N Width across flats D

PJ+Stroke

FP E

KK depth KL

PK

LF+Stroke

MM

EH LH ST

Width across flats D C 4-SB

TS US

SU

W XS

LL+Stroke SS+Stroke ZB+Stroke

*Please be sure to use the Socket Head Screw when install the cylinder to the contact patch.

SU SY

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

36

Dimension Table Symbol A

C

ø20

15(25)

6

10

44

ø25

18(30)

6

12

ø32

25(40)

7

ø40

30(45)

ø50

D

E

EE

KK

LH

KL

LF

M10✕1.25

10

73

24±0.15

M10✕1.5

M12✕1.25

12

75

27±0.15

48

M12✕1.75

M16✕1.5

15

94

35±0.15

72.5

47

M16✕2

M20✕1.5

20

95

37.5±0.15

Rc1/4

85

53

M20✕2.5

M24✕1.5

24

110

45±0.15

94

Rc1/4

97

55

M27✕3

M30✕1.5

33

117

50±0.15

114

Rc3/8

117

65

M30✕3.5

M39✕1.5

36

138

60±0.25

EH

FP

Rc1/8

46

35.5

M8✕1.25

50

Rc1/8

52

35.5

14

62

Rc1/4

66

7

19

70

Rc1/4

35(50)

8

24

80

ø63

45(60)

9

30

ø80

60(80)

14

41

Bore

Female thread

Male thread

Symbol LL

MM

N

PJ

PK

ø20

43

ø12

–

10.5

27

ø25

45

ø14

–

12.5

ø32

54

ø18

10

ø40

55

ø22

ø50

60

ø63 ø80

SB

SS

ST

SU

SY

TS

US

W

XS

ZB

6.6

58

12

15

7.5

58

70

8

15.5

81

27

6.6

60

12

15

7.5

64

76

8

15.5

83

14

32

9

74

16

20

10

79

94

10

20

104

10

16

32

11

75

20

20

10

90

108

10

20

105

ø28

10

19

38

14

85

24

25

12.5

104

126

11

23.5

121

67

ø36

10

24

38

16

92

30

25

12.5

121

146

13

25.5

130

78

ø45

15

25

48

18

108

35

30

15

144

172

17

32

155

Bore

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

Notes) • • • •

37

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

160S-1/THS16 Bore General purpose type 160S-1

FA

6 FA Bore N Stroke

T

(ø20 - ø80)

Cutting fluid proof type 160SW-1 6 FA Bore N Stroke

T

(ø32 - ø80)

CAD/DATA is available.

None : Female thread T : Male thread

• Bore ø20, ø25 Less than 15 strokes

• Male thread

Over 15 strokes

EE

EE

W

A KK

C

MM

Width across flats D Y

E

Y

PJ+ Stroke

PL

KK depth KL

TV

Compact Design Hydraulic Cylinder

PJ+ Stroke PL

EE

FE R

MM Width across flats D

4-FB

Width across flats D

C W F

TF

MM

4-M

LL+Stroke

4-M

C

UF

LL+Stroke

W F

LF+Stroke

LF+Stroke

• Bore ø32 - ø80 EE

• Male thread W

A C

KK

N N MM Width across flats D

Y

E TV

FE R

PJ+Stroke

PL

KK depth KL

MM 4-M Width across flats D C

4-FB

TF UF

W

F

LL+Stroke LF+Stroke

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

38

Dimension Table Symbol A

C

ø20

15(25)

6

10

44

Rc1/8

10

ø5.5

ø25

18(30)

6

12

50

Rc1/8

10

ø32

25(40)

7

14

62

Rc1/4

ø40

30(45)

7

19

70

ø50

35(50)

8

24

ø63

45(60)

9

ø80

60(80)

14

D

E

F

EE

FB

KK

FE

KL

LF

M10✕1.25

10

61

M10✕1.5

M12✕1.25

12

63

62

M12✕1.75

M16✕1.5

15

79

ø11

70

M16✕2

M20✕1.5

20

85

20

ø14

85

M20✕2.5

M24✕1.5

24

91

Rc1/4

20

ø14

98

M27✕3

M30✕1.5

33

100

Rc3/8

25

ø18

118

M30✕3.5

M39✕1.5

36

120

Female thread

Male thread

46

M8✕1.25

ø5.5

52

15

ø6.6

Rc1/4

20

80

Rc1/4

30

94

41

114

Bore

Symbol LL

M

MM

N

PJ

PL

R

TF

ø12

—

10.5

12

30

60

12.5

12

36

TV

UF

W

Y

30

75

8

20.5

66

36

80

8

20.5

Bore

M5 ✕0.8

ø25

45

M5 ✕0.8

ø14

—

ø32

54

M6 ✕1

ø18

10

14

12

40

80

47

95

10

28

ø40

55

M8 ✕1.25

ø22

10

16

12

46

96

52

118

10

27

ø50

60

M10 ✕1.5

ø28

10

19

13

58

108

58

135

11

28

67

M12 ✕1.75

124

69

150

13

30

78

M14 ✕2

154

86

185

17

35

ø63 ø80 Notes) • • • •

ø36 ø45

10 15

24 25

13 18

65 87

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

43

ø20

39

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

160S-1/THS16 Bore

FB

General purpose type 160S-1

6 FB Bore N Stroke

T

(ø20 - ø80)

Cutting fluid proof type 160SW-1 6 FB Bore N Stroke

T

(ø32 - ø80)

CAD/DATA is available.

None : Female thread T : Male thread

• Bore ø20, ø25 Over 15 strokes EE

Less than 15 strokes EE

• Male thread WF

A C

KK

MM

Width across flats D Y

E

PJ+ Stroke PL

PJ+ Stroke

EE

4-M

FE R

4-M

MM Width across flats D

4-FB TF

MM

Width across flats D

C WF

LL+Stroke

F

C WF

LF+Stroke

UF

LL+Stroke LF+Stroke

• Bore ø32 - ø80

EE

• Male thread WF

A C

KK

N N

Width across flats D

E TV

Y

PJ+Stroke

PL

KK depth KL

4-M

FE R

MM Width across flats D C

4-FB

PL

KK depth KL

TV

Compact Design Hydraulic Cylinder

Y

TF UF

WF

LL+Stroke LF+Stroke

F

F

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Standard Type Unit: mm

160S-1

40

Dimension Table Symbol A

C

ø20

15(25)

6

10

44

Rc1/8

10

f5.5

ø25

18(30)

6

12

50

Rc1/8

10

ø32

25(40)

7

14

62

Rc1/4

ø40

30(45)

7

19

70

ø50

35(50)

8

24

ø63

45(60)

9

ø80

60(80)

14

D

E

F

EE

FB

KK

FE

KL

LF

M10✕1.25

10

61

M10✕1.5

M12✕1.25

12

63

62

M12✕1.75

M16✕1.5

15

79

f11

70

M16✕2

M20✕1.5

20

85

20

f14

85

M20✕2.5

M24✕1.5

24

91

Rc1/4

20

f14

98

M27✕3

M30✕1.5

33

100

Rc3/8

25

f18

118

M30✕3.5

M39✕1.5

36

120

Female thread

Male thread

46

M8✕1.25

f5.5

52

15

f6.6

Rc1/4

20

80

Rc1/4

30

94

41

114

Bore

Symbol LL

M

MM

N

PJ

PL

R

TF

TV

UF

WF

Y

Bore

43

M5 ✕0.8

f12

—

10.5

12

30

60

30

75

8

20.5

ø25

45

M5 ✕0.8

f14

—

12.5

12

36

66

36

80

8

20.5

ø32

54

M6 ✕1

f18

10

14

12

40

80

47

95

10

28

ø40

55

M8 ✕1.25

f22

10

16

12

46

96

52

118

10

27

ø50

60

M10 ✕1.5

f28

10

19

13

58

108

58

135

11

28

ø63

67

M12 ✕1.75

f36

10

24

13

65

124

69

150

13

30

ø80

78

M14 ✕2

f45

15

25

18

87

154

86

185

17

35

Notes) • • • •

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

ø20

41

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Standard Type Unit: mm

160S-1

160S-1/THS16 Bore

SD

General purpose type 160S-1D

6 SD Bore N Stroke

T

(ø20 - ø125)

Cutting fluid proof type 160SW-1D

6 SD Bore N Stroke

T

(ø32 - ø100)

CAD/DATA is available.

None : Female thread T : Male thread

• Bore ø20, ø25

WF

A KK

Over 15 strokes EE

Less than 15 strokes EE

• Male thread C

KK depth KL

KK depth KL

MM

Width across flats D Y

Compact Design Hydraulic Cylinder

4-FB holes 2✕4-Counter hole diameter FG, Depth BT

PJ+ Stroke

Y

PJ+ Stroke

Y

EE

KK depth KL

V cut machined circle

V cut machined circle

MM Width across flats D C WF

TV E

Y

MM MM

LL+Stroke

MM

Width across flats D C WF+ Stroke WF

LL+Stroke

WF+ Stroke

• Bore ø32 - ø125 EE

• Male thread A

• G screw port DE

KK

FF

WF

C

KK depth KL N N

AE

Width across flats D

4-FB holes 2✕4-Counter hole diameter FG, Depth BT

Y

PJ+Stroke

KK depth KL

Y

V cut machined circle

MM

MM

Width across flats D C TV E

• Face with no V cut machined circle is for mounting.

WF

LL+Stroke

WF+Stroke

16MPa Compact Design Hydraulic Cylinder Unit: mm Double Acting Double-rod/Standard Type

160S-1

42

Dimension Table Symbol AE

A

BT

C

D

DE

E

EE

FB

FF

KK

FG

KL

Female thread Male thread

Bore

ø20 15(25)

–

5.4

6

10

–

44

Rc1/8

ø5.5

–

ø9.5

M8✕1.25

M10✕1.25

10

ø25 18(30)

–

5.4

6

12

–

50

Rc1/8

ø5.5

–

ø9.5

M10✕1.5

M12✕1.25

12

ø32 25(40)

8

6.5

7

14

ø17.2

62

Rc1/4

ø6.6

G1/8

ø11

M12✕1.75

M16✕1.5

15

ø40 30(45)

8

8.6

7

19

ø17.2

70

Rc1/4

ø9

G1/8

ø14

M16✕2

M20✕1.5

20

ø50 35(50)

12

10.8

8

24

ø21.5

80

Rc1/4

ø11

G1/4

ø17.5

M20✕2.5

M24✕1.5

24

ø63 45(60)

12

13

9

30

ø21.5

94

Rc1/4

ø14

G1/4

ø20

M27✕3

M30✕1.5

33

ø80 60(80)

12

15.2

14

41

ø21.5

114

Rc3/8

ø16

G1/4

ø23

M30✕3.5

M39✕1.5

36

ø100 75(95)

12

19.5

22

50

ø25.5

140

Rc3/8

ø20

G3/8

ø29

M39✕4

M48✕1.5

45

ø125 95(125)

14

23.5

25

65

ø30

172

Rc1/2

ø24

G1/2

ø35

M48✕5

M64✕2

58

Symbol LL

N

MM

PJ

TV

Rc thread G thread Rc thread G thread

Bore

Y

WF

Rc thread G thread

54

ø12

ø25

56

ø14

–

–

15

–

36

8

ø32

72

ø18

10

10

16

16

47

10

28

28

ø40

72

ø22

10

10

18

18

52

10

27

27

ø50

75

ø28

10

14

19

19

58

11

28

28

ø63

82

ø36

10

16

22

22

69

13

30

30

ø80

95

ø45

15

19

25

23

86

17

35

36

ø100

108

ø56

15

18

24

24

106

26

42

42

ø125

120

ø70

25

25

28

28

132

30

46

46

Notes) • • • •

–

13

–

30

8

20.5

–

20.5

–

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

ø20

–

43

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Standard Type Unit: mm

160S-1

CAD/DATA is available.

160S-1/THS16 Bore

LA

General purpose type 160S-1D

6 LA Bore N Stroke

T

(ø32 - ø63)

None : Female thread T : Male thread

• Bore ø32 - ø63 4-GB holes 4-Counter hole diameter FG, Depth BT

• Male thread A

SY

SV+Stroke

SY

2-EE

WF C

KK

KK depth KL N N

MM Width across flats D

Compact Design Hydraulic Cylinder

EA TS

Y

PJ+Stroke

Y

KK depth KL

EB

V cut machined circle

MM

MM

LH

Width across flats D T

C TX WF

TW TZ+Stroke LJ+Stroke

WF+Stroke

16MPa Compact Design Hydraulic Cylinder Unit: mm Double Acting Double-rod/Standard Type

160S-1

44

Dimension Table Symbol BT

A

C

EA

D

EB

EE

FG

KK

GB

Bore

KL

Female thread

Male thread

ø32

25(40)

8.6

7

14

70

56

Rc1/4

ø14

ø9

M12✕1.75

M16✕1.5

15

ø40

30(45)

10.8

7

19

80

64

Rc1/4

ø17.5

ø11

M16✕2

M20✕1.5

20

ø50

35(50)

13

8

24

94

74

Rc1/4

ø20

ø14

M20✕2.5

M24✕1.5

24

ø63

45(60)

15.2

9

30

114

89

Rc1/4

ø23

ø16

M27✕3

M30✕1.5

33

Symbol LH

LJ

MM

N

PJ

SV

SY

T

TS

TW

TX

TZ

WF

Y

ø32

25±0.06

72

ø18

10

16

32

20

63

56

12

28

32

10

28

ø40

29±0.06

72

ø22

10

18

32

20

70

62

12

28

32

10

27

ø50

34±0.06

75

ø28

10

19

35

20

80

74

14

29

32

11

28

ø63

42±0.06

82

ø36

10

22

42

20

100

90

16

31

35

13

30

Bore

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

When using a parallel key:

b1

Parallel key attached to the cylinder r1

t1

r1

When not using a parallel key: Pulling stopper

Use the same dimensions for the stopper as the attached parallel key.

Dimension Table Key’s Nominal Dimensions b✕h✕1

b1

t1

ø32

12✕8✕63 (Both rounded)

0 12 –0.043

5 +0.2 0

ø40

12✕8✕70 (Both rounded)

0 12 –0.043

5 +0.2 0

ø50

14✕9✕80 (Both rounded)

0 14 –0.043

5.5 +0.2 0

ø63

16✕10✕100 (Both rounded)

0 16 –0.043

6 +0.2 0

Bore

Pushing stopper

Key Way Dimensions

r1

0.25 - 0.40

• When using the foot type, use the attached parallel key to install the cylinder, referring to the “Recommended Key Way Dimensions.” • When not using the parallel key, attach the stoppers to the cylinder’s front and rear sides toward its stroke direction. If the cylinder is used without using the key or stoppers, a large force is applied to the cylinder’s mounting bolts, possibly resulting in the fracturing of the bolts.

Compact Design Hydraulic Cylinder

Recommended Key Way Dimensions

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Standard Type Unit: mm

160S-1

45

CAD/DATA is available.

160S-1/THS16 Bore

LD

General purpose type 160S-1D

6 LD Bore N Stroke

T

(ø20 - ø80)

Cutting fluid proof type 160SW-1D

6 LD Bore N Stroke

T

(ø32 - ø80) None : Female thread T : Male thread

• Bore ø20, ø25 • Male thread KK

Less than 15 strokes

Over 15 strokes

EE

A W C

EE KK depth KL

KK depth KL

MM Width across flats D PJ+ Stroke

FP KK depth KP

E

LH

MM

SU

W

TS

4-SB

FP

EE

Width across flats D C

ST

PJ+ Stroke

FP

MM

EH

Compact Design Hydraulic Cylinder

FP

XS

US

W+ SU Stroke

LZ+Stroke

W

SU

LZ+Stroke

XS

XS+Stroke

SV+Stroke

MM

MM

Width across flats D C C

SV+Stroke

ZZ+Stroke✕2

W+ SU Stroke

C

XS+Stroke

ZZ+Stroke✕2

• Bore ø32 - ø80 EE

• Male thread A

W C

KK

KK depth KL N MM N Width across flats D

FP E

PJ+Stroke

FP

LG+Stroke

KK depth KL

MM

MM

EH LH ST

4-SB

Width across flats D TS US

C

C SU

W XS

LZ+Stroke SV+Stroke ZZ+Stroke✕2

*Please be sure to use the Socket Head Screw when install the cylinder to the contact patch.

SU

W+Stroke XS+Stroke

16MPa Compact Design Hydraulic Cylinder Unit: mm Double Acting Double-rod/Standard Type

160S-1

46

Dimension Table Symbol A

C

ø20

15(25)

6

10

44

ø25

18(30)

6

12

ø32

25(40)

7

ø40

30(45)

ø50

D

E

EE

KK

KL

LG

M10✕1.25

10

84

24±0.15

M10✕1.5

M12✕1.25

12

86

27±0.15

48

M12✕1.75

M16✕1.5

15

112

35±0.15

72.5

47

M16✕2

M20✕1.5

20

112

37.5±0.15

Rc1/4

85

53

M20✕2.5

M24✕1.5

24

125

45±0.15

94

Rc1/4

97

55

M27✕3

M30✕1.5

33

132

50±0.15

114

Rc3/8

117

65

M30✕3.5

M39✕1.5

36

155

60±0.25

EH

FP

Rc1/8

46

50

Rc1/8

14

62

7

19

35(50)

8

ø63

45(60)

ø80

60(80)

Female thread

Male thread

33.5

M8✕1.25

52

35.5

Rc1/4

66

70

Rc1/4

24

80

9

30

14

41

Bore

LH

Symbol LZ

MM

N

PJ

SB

ST

SU

SV

TS

US

W

54

ø12

–

13

6.6

12

15

69

58

70

8

15.5 100

ø14

–

15

6.6

12

15

71

64

76

8

15.5 102

ø18

10

16

9

16

20

92

79

94

10

20

132

ø22

10

18

11

20

20

92

90

108

10

20

132

ø28

10

19

14

24

25

100

104

126

11

23.5 147

ø36

10

22

16

30

25

107

121

146

13

25.5 158

ø45

15

25

18

35

30

125

144

172

17

32

XS

ZZ

Bore

ø20 ø25 ø32 ø40

ø63 ø80 Notes) • • • •

72 72 75 82 95

189

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

ø50

56

47

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Standard Type Unit: mm

160S-1

CAD/DATA is available.

160S-1/THS16 Bore

FA

General purpose type 160S-1D

6 FA Bore N Stroke

T

(ø20 - ø80)

Cutting fluid proof type 160SW-1D

6 FA Bore N Stroke

T

(ø32 - ø80) None : Female thread T : Male thread

• Bore ø20, ø25

EE

EE

W(WF)

A

Over 15 strokes

Less than 15 strokes

• Male thread C

KK

KK depth KL

KK depth KL

MM

Width across flats D Y

E TV

PJ+ Stroke

Y

Y

PJ+ Stroke

4-M

Compact Design Hydraulic Cylinder

Y

KK depth KL

MM

FE R

MM

C

W

TF UF

MM

Width across flats D

Width across flats D

4-FB

4-M

F

WF+Stroke W

LL+Stroke

MM

C F

LL+Stroke

WF+Stroke

• Bore ø32 - ø80 • Male thread A

EE

W(WF) C

KK

KK depth KL N N

MM Width across flats D

E TV

Y

PJ+Stroke

Y

KK depth KL 4-M

MM

MM

FE R

Width across flats D C 4-FB

TF UF

W

F

LL+Stroke

WF+Stroke

16MPa Compact Design Hydraulic Cylinder Unit: mm Double Acting Double-rod/Standard Type

160S-1

48

Dimension Table Symbol D

EE

E

F

FB

A

C

ø20

15(25)

6

10

44

Rc1/8

10

ø5.5

ø25

18(30)

6

12

50

Rc1/8

10

ø32

25(40)

7

14

62

Rc1/4

ø40

30(45)

7

19

70

ø63 ø80

35(50) 45(60) 60(80)

8 9 14

KL

Female thread

Male thread

46

M8✕1.25

M10✕1.25

10

ø5.5

52

M10✕1.5

M12✕1.25

12

15

ø6.6

62

M12✕1.75

M16✕1.5

15

Rc1/4

20

ø11

70

M16✕2

M20✕1.5

20

24

80

Rc1/4

20

ø14

85

M20✕2.5

M24✕1.5

24

30

94

Rc1/4

20

ø14

98

M27✕3

M30✕1.5

33

41

114

Rc3/8

25

ø18

118

M30✕3.5

M39✕1.5

36

TV

Bore

ø50

KK

FE

Symbol LL

M

MM

N

PJ

R

TF

UF

W

WF

Y

Bore

54

M5✕0.8

ø12

–

13

30

60

30

75

8

8

20.5

ø25

56

M5✕0.8

ø14

–

15

36

66

36

80

8

8

20.5

ø32

72

M6✕1

ø18

10

16

40

80

47

95

10

10

28

ø40

72

M8✕1.25

ø22

10

18

46

96

52

118

10

10

27

ø50

75

M10✕1.25

ø28

10

19

58

108

58

135

11

11

28

ø63

82

M12✕1.75

ø36

10

22

65

124

69

150

13

13

30

ø80

95

M14✕2

ø45

15

25

87

154

86

185

17

17

35

Notes) • • • •

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Compact Design Hydraulic Cylinder

ø20

49

160S-1

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm 160S-1/THS16 Bore

SD

CAD/DATA is available.

General purpose type 160S-1R

6 SD Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1R

6 SD Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 • Male thread A

• G screw port DE

KK

FF

WF

N N

MM

AE

EE

C

Width across flats D

Y

Cord extended to rear 4-FB holes AX type

Compact Design Hydraulic Cylinder

RV

PJ+Stroke

PL

Cord extended to top AZ type

2✕4-Counter hole diameter FG, Depth BT

RV

UX2

UX1

KK depth KL

MM Width across flats D C TV E

WF

LL+Stroke

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

50

General purpose type Dimension Table Symbol A

AE

ø32

25(40)

ø40

D

DE

E

EE

FB

FF

KK

BT

C

FG

8

6.5

7

14

ø17.2

62

Rc1/4

ø6.6

G1/8

ø11

M12 ✕1.75

M16 ✕1.5

15

30(45)

8

8.6

7

19

ø17.2

70

Rc1/4

ø9

G1/8

ø14

M16 ✕2

M20 ✕1.5

20

ø50

35(50)

12

10.8

8

24

ø21.5

80

Rc1/4

ø11

G1/4

ø17.5

M20 ✕2.5

M24 ✕1.5

24

ø63

45(60)

12

13

9

30

ø21.5

94

Rc1/4

ø14

G1/4

ø20

M27 ✕3

M30 ✕1.5

33

ø80

60(80)

12

15.2

14

41

ø21.5

114

Rc3/8

ø16

G1/4

ø23

M30 ✕3.5

M39 ✕1.5

36

Symbol LL

N

MM

KL

Female thread Male thread

Bore

PJ

PL

RV

TV

UX1

Y

UX2 WF

Rc thread G thread

Rc thread G thread Rc thread G thread Rc thread G thread AX type AZ type

Bore

ø32

54

ø18

10

10

14

14

12

12

37

44

47

19

17

10

28

28

ø40

55

ø22

10

10

16

16

12

12

41

48

52

20

17

10

27

27

ø50

60

ø28

10

14

19

13.5

13

18.5

46

53

58

22

20

11

28

28

ø63

67

ø36

10

16

24

20

13

17

53

60

69

24

25

13

30

30

ø80

78

ø45

15

19

25

24

18

18

63

70

86

30

30

17

35

36

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

12

16

ø40

41

57

48

57

82

114

96

114

14

17

20

11

14

16

ø50

46

62

53

62

92

124

106

124

16

19

21

14

16

20

ø63

54

69

61

69

108

138

122

138

17

20

24

18

21

23

ø80

63

79

70

79

126

158

140

158

22

25

29

22

25

29

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W (no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • • • •

51

160S-1 ST

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

General purpose type 160S-1R 6 ST Bore N Stroke

T

Switch symbol Quantity of Switch (ø32-ø80/Made-to-order)

– : Female thread T : Male thread over 101 strokes (110, 120, 130, 140, 150, 160, 170, 180, 190, 200)

• Bore ø32 - ø80 • Male thread A

EE

WF C

KK

N N

MM

Compact Design Hydraulic Cylinder

Width across flats D

Cord extended to rear AX type RV

Cord extended to top AZ type 2✕4-TT, Deapth BT

Y

PJ

Y

RV KK depth KL

UX2

UX1

MM Width across flats D

C TV WF E

LL

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

52

Dimension Table Symbol

RV

KK D

BT

C

ø32 25(40) 15

7

14

62

Rc1/4 M12 ✕1.75 M16 ✕1.5 15 ø18 10

37

44 M6✕1

47 29

35

10

28

ø40 30(45) 20

7

19

70

Rc1/4 M16 ✕2

M20 ✕1.5 20 ø22 10

41

48 M8✕1.25

52 30

34

10

27

ø50 35(50) 25

8

24

80

Rc1/4 M20 ✕2.5

M24 ✕1.5 24 ø28 10

46

53 M10✕1.5

58 32

35

11

28

ø63 45(60) 30

9

30

94

Rc1/4 M27 ✕3

M30 ✕1.5 33 ø36 10

53

60 M12✕1.75

69 34

40

13

30

ø80 60(80) 35

14

41

114 Rc3/8 M30 ✕3.5

M39 ✕1.5 36 ø45 15

63

70 M16✕2

86 40

47

17

35

A

EE

E

N

Female thread Male thread

Bore

Symbol Stroke

KL MM

TT

TV UX1 UX2 WF

Y

AX type AZ type

LL

PJ

110

120

130

140

150

160

170

180

190

200

110

120

130

140

150

160

170

180

190

200

ø32

192

202

212

222

232

242

252

262

272

282

136

146

156

166

176

186

196

206

216

226

ø40

192

202

212

222

232

242

252

262

272

282

138

148

158

168

178

188

198

208

218

228

ø50

195

205

215

225

235

245

255

265

275

285

139

149

159

169

179

189

199

209

219

229

ø63

202

212

222

232

242

252

262

272

282

292

142

152

162

172

182

192

202

212

222

232

ø80

215

225

235

245

255

265

275

285

295

305

145

155

165

175

185

195

205

215

225

235

Bore

Compact Design Hydraulic Cylinder

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

53

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1 LA

General purpose type 160S-1R

6 LA Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø63 • Male thread A

UX1

UX2

WF C

KK 4-GB holes 4-Counter hole diameter FG, Depth BT

MM Width across flats D

SG+Stroke

SE

SF

Compact Design Hydraulic Cylinder

EA TS

PJ+Stroke

Y

PL

KK depth KL

RV EB

N N

MM LH

C T

Width across flats D

WF

TX

TW

TZ+Stroke LJ+Stroke

2-EE

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

54

Dimension Table Symbol

KK D

EA

EB

EE

GB

FG

KL

LH

LJ

MM

M16✕1.5

15

25±0.06

72

ø18

M20✕1.5

20

29±0.06

72

ø22

ø14 M20✕2.5

M24✕1.5

24

34±0.06

75

ø28

ø16 M27✕3

M30✕1.5

33

42±0.06

82

ø36

A

BT

C

ø32

25(40)

8.6

7

14

70

56

Rc1/4

ø14

ø9

M12✕1.75

ø40

30(45)

10.8

7

19

80

64

Rc1/4

ø17.5

ø11

M16✕2

ø50

35(50)

13

8

24

94

74

Rc1/4

ø20

ø63

45(60)

15.2

9

30

114

89

Rc1/4

ø23

Female thread Male thread

Bore

Symbol N

PJ

PL

RV

SE

SF

SG

T

TS

TW

TX

TZ

UX1

UX2

WF

Y

ø32

8

16

28

62

13

13

46

63

56

12

28

32

19

35

10

28

ø40

10

18

27

70

13

13

46

70

62

12

28

32

20

34

10

27

ø50

10

15

30

80

13

13

49

80

74

14

29

32

22

35

11

30

ø63

10

18

32

95

15

15

52

100

90

16

31

35

24

40

13

32

Bore

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

When using a parallel key:

b1

Parallel key attached to the cylinder r1

t1

r1

When not using a parallel key:

Pulling stopper

Use the same dimensions for the stopper as the attached parallel key.

Dimension Table Key’s Nominal Dimensions b✕h✕1

b1

t1

ø32

12✕8✕63 (Both rounded)

0 12 –0.043

5 +0.2 0

ø40

12✕8✕70 (Both rounded)

0 12 –0.043

5 +0.2 0

ø50

14✕9✕80 (Both rounded)

0 14 –0.043

5.5 +0.2 0

ø63

16✕10✕100 (Both rounded)

0 16 –0.043

6 +0.2 0

Bore

Pushing stopper

Key Way Dimensions

r1

0.25 - 0.40

• When using the foot type, use the attached parallel key to install the cylinder, referring to the “Recommended Key Way Dimensions.” • When not using the parallel key, attach the stoppers to the cylinder’s front and rear sides toward its stroke direction. If the cylinder is used without using the key or stoppers, a large force is applied to the cylinder’s mounting bolts, possibly resulting in the fracturing of the bolts.

Compact Design Hydraulic Cylinder

Recommended Key Way Dimensions

55

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

CAD/DATA is available.

160S-1/THS16 Bore

LD

General purpose type 160S-1R

6 LD Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1R

6 LD Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 EE

• Male thread A KK

W C

N MM N

Compact Design Hydraulic Cylinder

Width across flats D

FP

PK

LF+Stroke

RV E

PJ+Stroke

UX1

KK depth KL

UX2

MM

EH LH ST

4-SB

Width across flats D

C SU

W

LL+Stroke

SU

TS XS

SS+Stroke

US ZB+Stroke

*Please be sure to use the Socket Head Screw when install the cylinder to the contact patch.

SY

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

56

General purpose type Dimension Table Symbol A

C

D

EE

ø32

25(40)

7

14

62

Rc1/4

66

ø40

30(45)

7

19

70

Rc1/4

ø50

35(50)

8

24

80

ø63

45(60)

9

30

ø80

60(80)

14

41

E

KL

LF

LH

LL

M16✕1.5

15

94

35±0.15

54

M16✕2

M20✕1.5

20

95

37.5±0.15

55

53

M20✕2.5

M24✕1.5

24

110

45±0.15

60

97

55

M27✕3

M30✕1.5

33

117

50±0.15

67

117

65

M30✕3.5

M39✕1.5

36

138

60±0.25

78

Female thread

Male thread

48

M12✕1.75

72.5

47

Rc1/4

85

94

Rc1/4

114

Rc3/8

Bore

Symbol MM

N

PJ

KK

FP

EH

RV

PK

SB

SS

ST

SU

SY

TS

US

UX1

UX2

W

XS

ZB

AX type AZ type

Bore

f32

f18

10

14

32

37

44

9

74

16

20

10

79

94

19

17

10

20

104

f40

f22

10

16

32

41

48

11

75

20

20

10

90

108

20

17

10

20

105

f50

f28

10

19

38

46

53

14

85

24

25

12.5

104

126

22

20

11

23.5 121

f63

f36

10

24

38

53

60

16

92

30

25

12.5

121

146

24

25

13

25.5 130

f80

f45

15

25

48

63

70

18

108

35

30

15

144

172

30

30

17

32

155

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

12

16

ø40

41

57

48

57

82

114

96

114

14

17

20

11

14

16

ø50

46

62

53

62

92

124

106

124

16

19

21

14

16

20

ø63

54

69

61

69

108

138

122

138

17

20

24

18

21

23

ø80

63

79

70

79

126

158

140

158

22

25

29

22

25

29

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W (no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

57

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

160S-1/THS16 Bore

FA

CAD/DATA is available.

General purpose type 160S-1R

6 FA Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1R

6 FA Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 • Male thread A

EE

W

C KK

N N

MM Width across flats D

Compact Design Hydraulic Cylinder

Y E TV

KK depth KL

FE R

UX2

UX1

RV

PL

PJ+Stroke

MM 4-M Width across flats D C

4-FB

TF UF

W

LL+Stroke

F

LF+Stroke

*Please be sure to use the Socket Head Screw when install the cylinder to the contact patch.

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

58

General purpose type Dimension Table Symbol EE

F

FB

KK

KL

LF

LL

M

M16 ✕1.5

15

79

54

M6 ✕1

M16 ✕2

M20 ✕1.5

20

85

55

M8 ✕1.25

85

M20 ✕2.5

M24 ✕1.5

24

91

60

M10 ✕1.5

ø14

98

M27 ✕3

M30 ✕1.5

33

100

67

M12 ✕1.75

ø18

118

M30 ✕3.5

M39 ✕1.5

36

120

78

M14 ✕2

A

C

ø32

25(40)

7

14

62

Rc1/4

15

ø6.6

62

M12 ✕1.75

ø40

30(45)

7

19

70

Rc1/4

20

ø11

70

ø50

35(50)

8

24

80

Rc1/4

20

ø14

ø63

45(60)

9

30

94

Rc1/4

20

ø80

60(80)

14

41

114

Rc3/8

25

D

E

FE

Female thread Male thread

Bore

Symbol MM

N

PJ

PL

RV

R

AX type AZ type

Bore

TF

TV

UF

UX1

UX2

W

Y

ø32

ø18

10

14

12

40

37

44

80

47

95

19

17

10

28

ø40

ø22

10

16

12

46

41

48

96

52

118

20

17

10

27

ø50

ø28

10

19

13

58

46

53

108

58

135

22

20

11

28

65

53

60

124

69

150

24

25

13

30

87

63

70

154

86

185

30

30

17

35

ø63 ø80

10

ø45

24

15

13

25

18

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

12

16

ø40

41

57

48

57

82

114

96

114

14

17

20

11

14

16

ø50

46

62

53

62

92

124

106

124

16

19

21

14

16

20

ø63

54

69

61

69

108

138

122

138

17

20

24

18

21

23

ø80

63

79

70

79

126

158

140

158

22

25

29

22

25

29

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W (no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • • • •

ø36

59

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

CAD/DATA is available.

160S-1/THS16 Bore

FB

General purpose type 160S-1R

6 FB Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1R

6 FB Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 • Male thread WF

A

EE

C KK

N N

MM Width across flats D

Y

PJ+Stroke

PL

Compact Design Hydraulic Cylinder

E TV

KK depth KL

UX2

UX1

RV 4-M

FE R

MM Width across flats D C

4-FB

TF UF

WF

LL+Stroke LF+Stroke

F

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

60

General purpose type Dimension Table Symbol C

A

D

E

EE

FB

F

KK

FE

Bore

KL

LF

LL

M

Female thread Male thread

ø32

25(40)

7

14

62

Rc1/4

15

ø6.6

62

M12✕1.75

M16✕1.5

15

79

54

M6 ✕1

ø40

30(45)

7

19

70

Rc1/4

20

ø11

70

M16✕2

M20✕1.5

20

85

55

M8 ✕1.25

ø50

35(50)

8

24

80

Rc1/4

20

ø14

85

M20✕2.5

M24✕1.5

24

91

60

M10 ✕1.5

ø63

45(60)

9

30

94

Rc1/4

20

ø14

98

M27✕3

M30✕1.5

33

100

67

M12 ✕1.75

ø80

60(80)

14

41

114

Rc3/8

25

ø18

118

M30✕3.5

M39✕1.5

36

120

78

M14 ✕2

MM

N

Symbol PJ

PL

RV

R

TF

TV

AX type AZ type

Bore

UF

UX1

UX2

WF

Y

ø32

ø18

10

14

12

40

37

44

80

47

95

19

17

10

28

ø40

ø22

10

16

12

46

41

48

96

52

118

20

17

10

27

ø50

ø28

10

19

13

58

46

53

108

58

135

22

20

11

28

ø63

ø36

10

24

13

65

53

60

124

69

150

24

25

13

30

ø80

ø45

15

25

18

87

63

70

154

86

185

30

30

17

35

When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. The lock nut needs to be ordered separately. 20mm and 25mm bore size of Cutting Fluid Proof Type are not available. Allowance of MM is f8.

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

12

16

ø40

41

57

48

57

82

114

96

114

14

17

20

11

14

16

ø50

46

62

53

62

92

124

106

124

16

19

21

14

16

20

ø63

54

69

61

69

108

138

122

138

17

20

24

18

21

23

ø80

63

79

70

79

126

158

140

158

22

25

29

22

25

29

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W(no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • • • •

61

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Switch set Unit: mm

160S-1

160S-1/THS16 Bore

SD

CAD/DATA is available.

General purpose type 160S-1RD

6 SD Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1RD

6 SD Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 • Male thread A

• G screw port DE

C

KK

FF

EE

WF

KK depth KL N N

MM

AE

Width across flats D

Compact Design Hydraulic Cylinder

Y

Cord extended to rear AX type

PJ+Stroke

Y

Cord extended to top AZ type

RV

RV

KK depth KL

UX2

UX1

V cut machined circle

MM

MM

Width across flats D 4-FB holes 2✕4-Counter hole diameter FG, Depth BT

C TV E

WF

LL+Stroke

WF+Stroke

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Switch set Unit: mm

160S-1

62

General purpose type Dimension Table Symbol

KK AE

A

C

BT

D

DE

E

EE

FB

FF

FG

Bore

KL Female thread Male thread

ø32

25(40)

8

6.5

7

14

ø17.2

62

Rc1/4

ø6.6

G1/8

ø11

M12✕1.75

M16✕1.5

15

ø40

30(45)

8

8.6

7

19

ø17.2

70

Rc1/4

ø9

G1/8

ø14

M16✕2

M20✕1.5

20

ø50

35(50)

12

10.8

8

24

ø21.5

80

Rc1/4

ø11

G1/4

ø17.5

M20✕2.5

M24✕1.5

24

ø63

45(60)

12

13

9

30

ø21.5

94

Rc1/4

ø14

G1/4

ø20

M27✕3

M30✕1.5

33

ø80

60(80)

12

15.2

14

41

ø21.5

114

Rc3/8

ø16

G1/4

ø23

M30✕3.5

M39✕1.5

36

Symbol

N

PJ

RV

UX2 WF

Y

LL

MM

ø32

72

ø18

10

10

16

14

37

44

47

19

35

10

28

28

ø40

72

ø22

10

10

18

16

41

48

52

20

34

10

27

27

ø50

75

ø28

10

14

19

13.5

46

53

58

22

35

11

28

28

ø63

82

ø36

10

16

22

20

53

60

69

24

40

13

30

30

ø80

95

ø45

15

19

25

24

63

70

86

30

47

17

35

36

Rc thread G thread Rc thread G thread AX type AZ type

Bore

TV

UX1

Rc thread G thread

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

28

32

ø40

41

57

48

57

82

114

96

114

14

17

20

11

33

36

ø50

46

62

53

62

92

124

106

124

16

19

21

14

35

37

ø63

54

69

61

69

108

138

122

138

17

20

24

18

36

40

ø80

63

79

70

79

126

158

140

158

22

25

29

22

43

47

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W (no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

63

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Switch set Unit: mm

160S-1

160S-1/THS16 Bore

LD

CAD/DATA is available.

General purpose type 160S-1RD

6 LD Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1RD

6 LD Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 EE

• Male thread A

W C

KK

KK depth KL N MM N

Width across flats D

FP

Compact Design Hydraulic Cylinder

FP

LG+Stroke

RV E

PJ+Stroke

UX1

KK depth KL

UX2

MM

MM

EH LH ST

4-SB

Width across flats D

C

C W

TS US

SU XS

LZ+Stroke SV+Stroke ZZ+Stroke✕2

*Please be sure to use the Socket Head Screw when install the cylinder to the contact patch.

SU

W+Stroke XS+Stroke

16MPa Compact Design Hydraulic Cylinder Double Acting Double-rod/Switch set Unit: mm

160S-1

64

General purpose type Dimension Table Symbol EE

KK

KL

LG

M16✕1.5

15

112

35±0.15

72

M16✕2

M20✕1.5

20

112

37.5±0.15

72

53

M20✕2.5

M24✕1.5

24

125

45±0.15

75

97

55

M27✕3

M30✕1.5

33

132

50±0.15

82

117

65

M30✕3.5

M39✕1.5

36

155

60±0.25

95

XS

ZZ

A

C

ø32

25(40)

7

14

62

Rc1/4

66

48

M12✕1.75

ø40

30(45)

7

19

70

Rc1/4

72.5

47

ø50

35(50)

8

24

80

Rc1/4

85

ø63

45(60)

9

30

94

Rc1/4

ø80

60(80)

14

41

114

Rc3/8

D

E

EH

FP

Symbol MM

N

RV

PJ

LH

LZ

Female thread Male thread

Bore

SB

ST

SU

SV

TS

US

UX1

UX2

W

AX type AZ type

Bore

ø32

ø18

10

16

37

44

9

16

20

92

79

94

19

35

10

20

132

ø40

ø22

10

18

41

48

11

20

20

92

90

108

20

34

10

20

132

ø50

ø28

10

19

46

53

14

24

25

100

104

126

22

35

11

23.5

147

ø63

ø36

10

22

53

60

16

30

25

107

121

146

24

40

13

25.5

158

ø80

ø45

15

25

63

70

18

35

30

125

144

172

30

47

17

32

189

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

28

32

ø40

41

57

48

57

82

114

96

114

14

17

20

11

33

36

ø50

46

62

53

62

92

124

106

124

16

19

21

14

35

37

ø63

54

69

61

69

108

138

122

138

17

20

24

18

36

40

ø80

63

79

70

79

126

158

140

158

22

25

29

22

43

47

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W (no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

65

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

160S-1/THS16 Bore

FA

CAD/DATA is available.

General purpose type 160S-1RD

6 FA Bore N Stroke

T

Switch symbol

Quantity of Switch

Cutting fluid proof type 160SW-1RD

6 FA Bore N Stroke

T

Switch symbol

Quantity of Switch

– : Female thread T : Male thread

• Bore ø32 - ø80 • Male thread EE

W(WF)

A C KK

KK depth KL N N

MM Width across flats D

Y

PJ+Stroke

Y

Compact Design Hydraulic Cylinder

E TV

KK depth KL

UX1

RV

UX2 4-M

MM

FE R

MM

Width across flats D C 4-FB

TF

W

F

LL+Stroke

UF

*Please be sure to use the Socket Head Screw when install the cylinder to the contact patch.

WF+Stroke

16MPa Compact Design Hydraulic Cylinder Double Acting Single-rod/Switch set Unit: mm

160S-1

66

General purpose type Dimension Table Symbol

KK

A

C

D

E

EE

F

FB

FE

ø32

25(40)

7

14

62

Rc1/4

15

ø6.6

62

M12✕1.75

ø40

30(45)

7

19

70

Rc1/4

20

ø11

70

ø50

35(50)

8

24

80

Rc1/4

20

ø14

ø63

45(60)

9

30

94

Rc1/4

20

ø80

60(80)

14

41

114

Rc3/8

25

KL

LL

M16✕1.5

15

72

M16✕2

M20✕1.5

20

72

85

M20✕2.5

M24✕1.5

24

75

ø14

98

M27✕3

M30✕1.5

33

82

ø18

118

M30✕3.5

M39✕1.5

36

95

Bore

Symbol M

MM

N

PJ

RV

R

TF

TV

Female thread Male thread

UF

UX1

UX2

W

WF

Y

AX type AZ type

Bore

f32

M6 ✕1

ø18

10

16

40

37

44

80

47

95

19

35

10

10

28

f40

M8 ✕1.25

ø22

10

18

46

41

48

96

52

118

20

34

10

10

27

f50

M10 ✕1.5

ø28

10

19

58

46

53

108

58

135

22

35

11

11

28

f63

M12 ✕1.75

ø36

10

22

65

53

60

124

69

150

24

40

13

13

30

f80

M14 ✕2

ø45

15

25

87

63

70

154

86

185

30

47

17

17

35

Cutting fluid proof type

Dimension Table RV

RY

UX1

R2

5o

UX2

Bore Cord rear wiring Cord upper wiring Cord rear wiring Cord upper wiring AX205W WR AX205W WR•WS AZ205W WR•WS AX205W WR•WS AZ205W WR•WS AZ205W

WS

rm

AX205W WR AZ205W

WS

ø32

37

53

44

53

74

106

88

106

13

11

15

11

28

32

ø40

41

57

48

57

82

114

96

114

14

17

20

11

33

36

ø50

46

62

53

62

92

124

106

124

16

19

21

14

35

37

ø63

54

69

61

69

108

138

122

138

17

20

24

18

36

40

ø80

63

79

70

79

126

158

140

158

22

25

29

22

43

47

ore

Recessed for the bend radius dimension.

When the switch cannot be attached as shown above, use the other type (cord upper wiring).

Note) Set the flex tube so that its bend radius becomes R25 or more. If the bend radius becomes smaller than this value, the cord may be disconnected.

Switch attachment dimensions • Cord rear wiring

• Cord upper wiring WR525 (contact)

AX205W (no contact)

WS235-1 (no contact)

RY RV

WR535 (contact) AZ205W (no contact)

RY RV

RV

WS245-1 (no contact)

RY RV

RV

RY RV

RV

RV

Compact Design Hydraulic Cylinder

Notes) • When you use the cylinder with lock nut, we recommend you change A dimension for parenthetic one. • The lock nut needs to be ordered separately. • Allowance of MM is f8.

160S-1

67

16MPa Compact Design Hydraulic Cylinder

Unit: mm

Special specification at the rod end • You can easily order following categolized items using the Semi-standard symbols and dimensional parameters. (No need to specify dimensional parameters if you would apply the basic dimensions.)

A00 (T) 3

KM✕KP

How to order Series Model number – X

15°

✽MM

Width across flats ✽S

Semi-standard symbols Dimensional parameters

A

WF

Parameter KM and KP need to be specified as a pair.

ex.

A83

Basic Dimension Table (Standard Dimensions)

3 ✽DR

✽DM

15°

✽DP

.2

C0

Compact Design Hydraulic Cylinder

✽MM

C1 ✽A2

✽A1

FA=W SD·FB=WF

✽A φ40~φ80 Note) Only WF dimension can be changed at A82 and A83 special rod end shape. If you would like to change other.

Bore

A

KM

KP

✽MM

✽S

WF

ø20

15

10

1.25

ø12

10

8

ø25

18

12

1.25

ø14

12

8

ø32

25

16

1.5

ø18

14

10

ø40

30

20

1.5

ø22

19

10

ø50

35

24

1.5

ø28

24

11

ø63

45

30

1.5

ø36

30

13

ø80

60

39

1.5

ø45

41

17

• A83, bore:40mm, WF:60mm 160S-1 6SD40N50T-X A83 WF-60

A51

A53 KM✕KP

Number of chamfering DN

3

3

15°

15° ✽øMM

✽MM

Width across flats ✽S A

L

WF

WF Note) Lengthen WF dimension by combining with L dimension.

Basic Dimension Table

Basic Dimension Table

Bore

✽MM

WF

Bore

A

DN

KM

KP

L

✽MM

✽S

WF

ø20

ø12

8

ø20

15

2

10

1.25

0

ø12

10

8

ø25

ø14

8

ø25

18

2

12

1.25

0

ø14

12

8

ø32

ø18

10

ø32

25

2

16

1.5

0

ø18

14

10

ø40

ø22

10

ø40

30

2

20

1.5

0

ø22

19

10

ø50

ø28

11

ø50

35

2

24

1.5

0

ø28

24

11

ø63

ø36

13

ø63

45

2

30

1.5

0

ø36

30

13

ø80

ø45

17

ø80

60

2

39

1.5

0

ø45

41

17

Use this type when the width across flats S of the A00 are required to be moved.

• Dimensions indicated by ✽Mark are fixed as our semi-standard. • You are requested to consult us if you would like to change fixed dimensions.

Unit: mm

160S-1

16MPa Compact Design Hydraulic Cylinder

68

A81

A54 Number of beveled locations DN

Width across flats ✽S

KM✕KP

KM✕KP

✽MM

Number of beveled locations DN

A

✽MM ✽A1

Width across flats ✽S 3

L

A

15°

WF

L

WF

Basic Dimension Table

Basic Dimension Table KP

L

✽MM ✽S WF

Bore

A

DN

KM

KP

L

✽MM

✽S

WF

2

10

1.25

0

ø12

10

8

ø20

10

2

8

1.25

0

ø12

10

8

4

2

12

1.25

0

ø14

12

8

ø25

12

2

10

1.5

0

ø14

12

8

25

4

2

16

1.5

0

ø18

14

10

ø32

15

2

12

1.75

0

ø18

14

10

ø40

30

4

2

20

1.5

0

ø22

19

10

ø40

20

2

16

2

0

ø22

19

10

ø50

35

4

2

24

1.5

0

ø28

24

11

ø50

24

2

20

2.5

0

ø28

24

11

ø63

45

4

2

30

1.5

0

ø36

30

13

ø63

33

2

27

3

0

ø36

30

13

ø80

60

4

2

39

1.5

0

ø45

41

17

ø80

36

2

30

3.5

0

ø45

41

17

A

ø20

15

4

ø25

18

ø32

A82 3

✽Exclusive M joint on the following pages.

3

3 ✽DR

✽DR

15°

A83 15°

15°

✽DM

✽DM ✽DP

✽DP

✽MM

✽MM

✽A2

✽A1

.2

C1

C0

.2

C0

✽A2

FA=W ✽A1 SD·FB=WF ✽A

FA=W SD·FB=WF

✽A φ40~φ80

Basic Dimension Table (Standard dimension)

Basic Dimension Table (Standard dimension)

W WF +0.5 –0.2 –0.2 Bore ✽A ✽A1+0.3 ✽A2–0.3 ✽DM ✽DP–0.3 ✽DR ✽MM ŶA ŶA ŶA FA type SD·FB type

W WF +0.5 –0.2 –0.1 –0.2 ✽DP –0.3 ✽DR ✽MM ✽A2 –0.3 ✽DM –0.4 Bore ✽A ✽A1+0.3 ŶA ŶA ŶD FA type SD·FB type

ø20 25

12.5

12.5

ø12

ø8

0.5 ø12 20

20

ø40 25

12.5

12.5

ø18

ø13

1.0 ø22 35

35

ø25 25

12.5

12.5

ø14

ø10

0.5 ø14 20

20

ø50 25

12.5

12.5

ø22

ø16

1.5 ø28 35

35

ø32 25

12.5

12.5

ø18

ø13

1.0 ø18 30

30

ø63 25

12.5

12.5

ø28

ø21

1.5 ø36 40

40

ø40 25

12.5

12.5

ø22

ø16

1.5 ø22 35

35

ø80 30

15

15

ø36

ø26

2.0 ø45 45

45

ø50 25

12.5

12.5

ø28

ø21

1.5 ø28 35

35

ø63 30

15

15

ø36

ø26

2.0 ø36 40

40

ø80 30

15

15

ø45

ø31

2.0 ø45 45

45

• Dimensions indicated by ✽Mark are fixed as our semi-standard. • You are requested to consult us if you would like to change fixed dimensions.

Compact Design Hydraulic Cylinder

✽A1 DN KM

Bore

69

160S-1

16MPa Compact Design Hydraulic Cylinder

Separate flange joint : Only for A82 rod end style

F G 4-D3 Reverse face/counter hole diameter D4 depth H

45˚

D2

D1

C

A

C

Compact Design Hydraulic Cylinder

J

B

B

E

3

• Need additional order for this item. Part No.: RMH-(bore(mm))

Unit: mm

Unit: mm

160S-1

16MPa Compact Design Hydraulic Cylinder

70

Dimension Table Symbol Parts code

A

B

C

D1

D2

D3

D4

E

F

G

H

J

Bore

ø20

RMH-12

ø44

20.5

0.5

ø13

ø8.5

ø5.5

ø9.5

19.6

25

12.5

5.4

ø29

ø25

RMH-14

ø46

21.5

0.5

ø15

ø10.5

ø5.5

ø9.5

19.6

25

12.5

5.4

ø31

ø32

RMH-18

ø49

23

1

ø19

ø13.5

ø6.6

ø11

18.5

25

12.5

6.5

ø34

ø40

RMH-22

ø57

27

1.5

ø23

ø16.5

ø9

ø14

16.4

25

12.5

8.6

ø40

ø50

RMH-28

ø71

34

1.5

ø29

ø21.5

ø11

ø17.5

14.2

25

12.5

10.8

ø50

ø63

RMH-36

ø77

37

2

ø38

ø27

ø11

ø17.5

19.2

30

15

10.8

ø55

ø80

RMH-45

ø100

48.5

2

ø48

ø33

ø14

ø20

17

30

15

13

ø76

Compact Design Hydraulic Cylinder