DRILL & REAMER BLANKS

WIRE SIZE HUTCHINSON HSS BLANKS

Wire Size

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Decimal Equivalent

.2280 .2210 .2130 .2090 .2055 .2040 .2010 .1990 .1960 .1935 .1910 .1890 .1850 .1820 .1800 .1770 .1730 .1695 .1660 .1610 .1590 .1570 .1540 .1520 .1495 .1470 .1440 .1405 .1360 .1285

Length Overall Inches

3 7/8 3 7/8 3 3/4 3 3/4 3 3/4 3 3/4 3 5/8 3 5/8 3 5/8 3 5/8 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 3 3/8 3 3/8 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 3 3 3 3 3 3 3 2 3/4

M2

Net Price Each

2.48 2.48 2.48 2.48 2.48 2.21 2.21 2.21 2.21 2.21 1.94 1.94 1.86 1.86 1.86 1.68 1.68 1.68 1.65 1.65 1.65 1.65 1.65 1.65 1.65 1.46 1.46 1.46 1.46 1.46

M42

Net Price Each

Wire Size

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

3.74 3.74 3.74 3.74 3.74 3.34 3.34 3.34 3.34 3.34 2.93 2.93 2.86 2.86 2.86 2.58 2.58 2.58 2.47 2.47 2.47 2.47 2.47 2.47 2.47 2.20 2.20 2.20 2.20 2.20

CHOICE OF TOLERANCE

M2 M42

Length Overall Inches

Decimal Equivalent

.1200 .1160 .1130 .1110 .1100 .1065 .1040 .1015 .0995 .0980 .0960 .0935 .0890 .0860 .0820 .0810 .0785 .0760 .0730 .0700 .0670 .0635 .0595 .0550 .0520 .0465 .0430 .0420 .0410 .0400

+ .0002 – .0000

2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 2 2 2 2 2 1 7/8 1 7/8 1 7/8 1 7/8 1 3/4 1 3/4 1 5/8 1 5/8 1 5/8

OR

1.38 1.37 1.37 1.37 1.37 1.37 1.37 1.37 1.37 1.37 1.33 1.33 1.33 1.33 1.33 1.33 1.30 1.30 1.30 1.30 1.30 1.25 1.25 1.25 1.25 1.31 1.31 1.31 1.31 1.31

M42

Net Price Each

2.14 2.10 2.10 2.10 2.10 2.08 2.08 2.08 2.08 2.08 2.00 2.00 2.00 2.00 2.00 2.00 1.99 1.99 1.99 1.99 1.99 1.84 1.84 1.84 1.84 1.94 1.94 1.94 1.94 1.94

+ .0000 – .0002

Typical Analysis of M2 and M42 High Speed Steel C Cr Mo W V Co Hardness .83 4.0 5.0 6.0 2.0 — R/C 62-64 1.10 3.75 9.50 1.50 1.15 8.25 R/C 66-68

QUICK DELIVERY DIRECT FROM OUR PLANT NO ORDER TOO SMALL

CUT COSTS – USE HUTCHINSON HSS BLANKS FOR PUNCHES, EJECTOR PINS AND DOWELS.

WILLIAM T. HUTCHINSON CO.

Page 2

M2

Net Price Each

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

DRILL & REAMER BLANKS

WIRE SIZE HUTCHINSON HSS BLANKS HUTCHINSON HSS BLANKS ARE AVAILABLE IN ANY DIAMETER .005" - 1.500" GROUND TO .0002 TOLERANCE LENGTHS UP TO 36" TO SUIT YOUR REQUIREMENTS All standard size High Speed Steel blanks available for quick delivery from our plant M2 HSS - R/C 62-64

Wire Size

61 62 63 64 65 66 67 1/32 68 69 70 71 72 73 74 75 76 77 78 1/64 79 80

Decimal Equivalent

.0390 .0380 .0370 .0360 .0350 .0330 .0320 .03125 .0310 .0292 .0280 .0260 .0250 .0240 .0225 .0210 .0200 .0180 .0160 .015625 .0145 .0135

Length Overall Inches

1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2

M2

M42 HSS - R/C 66-68

M42

Net Price Each

Wire Size

Net Price Each

1.50 1.50 1.50 1.50 1.69 1.69 1.69 1.69 1.69 1.83 1.83 1.83 2.14 2.14 2.14 2.14 2.64 2.64 2.64 2.64 2.64 2.64

61 62 63 64 65 66 67 1/32 68 69 70 71 72 73 74 75 76 77 78 1/64 79 80

2.03 2.03 2.03 2.03 2.32 2.32 2.32 2.32 2.32 2.39 2.39 2.39 2.99 2.99 2.99 2.99 3.68 3.68 3.68 3.68 3.68 3.68

CHOICE OF TOLERANCE ONE END SOFT BLANKS AND BLANKS OF SPECIAL HARDNESS AVAILABLE

Length Overall Inches

Decimal Equivalent

.0390 .0380 .0370 .0360 .0350 .0330 .0320 .03125 .0310 .0292 .0280 .0260 .0250 .0240 .0225 .0210 .0200 .0180 .0160 .015625 .0145 .0135

+ .0002 – .0000

2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

OR

1.84 1.84 1.84 1.84 1.99 1.99 1.99 1.99 1.99 2.36 2.36 2.36 2.69 2.69 2.69 2.69 3.55 3.55 3.55 3.55 3.55 3.55

M42

Net Price Each

2.53 2.53 2.53 2.53 2.74 2.74 2.74 2.74 2.74 3.28 3.28 3.28 3.75 3.75 3.75 3.75 5.00 5.00 5.00 5.00 5.00 5.00

+ .0000 – .0002

QUANTITY DISCOUNTS

The following discounts apply to orders for blanks of standard length and standard diameter only: 100 pieces of one size 5% 250 pieces of one size 7 1/2% 500 pieces of one size 10% 1000 pieces of one size 15%

LIMITED SIZES OF M7 AVAILABLE

M2

Net Price Each

WHEN ORDERING, SPECIFY: DIAMETER LENGTH TOLERANCES

PRICES & AVAILABILITY UPON REQUEST

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

•

453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 3

DRILL & REAMER BLANKS

FRACTIONAL & LETTER SIZE HUTCHINSON HSS BLANKS

Size

1/64 1/32 3/64 1/16 5/64 3/32 7/64 1/8 9/64 5/32 11/64 3/16 13/64 7/32 15/64 1/4 17/64 9/32 19/64 5/16 21/64 11/32 23/64 3/8 25/64 13/32 27/64 7/16 29/64 15/32 31/64 1/2

Decimal Equivalent

.015625 .03125 .046875 .0625 .078125 .09375 .109375 .1250 .140625 .15625 .171875 .1875 .203125 .21875 .234375 .2500 .265625 .28125 .296875 .3125 .328125 .34375 .359375 .3750 .390625 .40625 .421875 .4375 .453125 .46875 .484375 .5000

Length Overall Inches

1 1/2 1 1/2 1 3/4 1 7/8 2 2 1/4 2 3/4 2 3/4 3 3 1/4 3 1/4 3 1/2 3 5/8 3 3/4 3 7/8 4 4 1/8 4 1/4 4 3/8 4 1/2 4 5/8 4 3/4 4 7/8 5 5 1/8 5 1/4 5 3/8 5 1/2 5 5/8 5 3/4 5 7/8 6

M2

Net Price Each

2.48 1.53 1.31 1.25 1.30 1.33 1.37 1.39 1.46 1.66 1.70 1.86 2.22 2.49 2.69 2.89 3.23 3.49 3.78 4.15 4.49 4.95 5.31 5.89 6.48 7.11 7.90 8.43 9.00 9.50 10.25 10.75

M42

Net Price Each

3.53 2.16 1.90 1.84 1.90 2.00 2.08 2.14 2.20 2.49 2.54 2.86 3.38 3.75 4.10 4.45 5.04 5.44 5.97 6.48 6.99 7.69 8.38 9.43 10.10 11.11 12.29 13.14 13.91 14.56 15.70 16.80

CHOICE OF TOLERANCE

M2

Letter Size Diameter

Decimal Equivalent

Length Overall Inches

Net Price Each

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

.234 .238 .242 .246 .250 .257 .261 .266 .272 .277 .281 .290 .295 .302 .316 .323 .332 .339 .348 .358 .368 .377 .386 .397 .404 .413

3 7/8 4 4 4 4 4 1/8 4 1/8 4 1/8 4 1/8 4 1/4 4 1/4 4 1/4 4 3/8 4 3/8 4 1/2 4 5/8 4 3/4 4 3/4 4 7/8 4 7/8 5 5 5 1/8 5 1/8 5 1/4 5 1/4

2.72 2.72 2.72 2.89 2.89 3.23 3.23 3.23 3.43 3.48 3.48 3.55 3.78 3.78 4.17 4.49 4.51 4.93 5.31 5.31 5.89 5.89 6.30 6.30 6.90 7.00

+ .0002 – .0000

OR

M42

Net Price Each

4.12 4.12 4.12 4.45 4.45 5.04 5.04 5.04 5.35 5.45 5.45 5.55 5.97 5.97 6.46 6.99 6.99 7.67 8.38 8.38 9.46 9.46 9.92 9.92 10.92 10.92

+ .0000 – .0002

A NOTE TO REMEMBER: We have large stocks of semi-finished material ready to be ground to meet your requirements. CUT COSTS – HUTCHINSON HSS BLANKS FOR MANDRELS AND SPECIAL END MILLS.

WILLIAM T. HUTCHINSON CO.

Page 4

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

Size

Decimal Equivalent

17/32

.53125

35/64

.546875

9/16

.5625

37/64

.578125

19/32

.59375

39/64

.609375

33/64

5/8

.515625

.6250

41/64

.640625

21/32

.65625

43/64

.671875

11/16

.6875

45/64

.703125

23/32

.71875

47/64

.734375

3/4

.7500

Length Overall Inches

6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12

M2

M42

Net Price Each

Net Price Each

13.52 22.76 30.41 13.91 24.08 31.65 14.31 24.67 32.78 15.46 26.34 34.28 15.87 27.11 36.63 16.92 28.55 38.39 17.91 30.15 39.85 18.38 31.02 41.24 19.68 34.00 44.65 20.29 34.80 45.69 21.48 35.65 47.43 21.70 37.20 49.22 22.71 38.50 51.44 23.91 39.87 53.15 24.54 40.39 54.25 25.11 42.08 54.68

20.44 35.08 46.90 21.00 37.12 48.77 21.62 38.01 50.50 22.91 40.60 52.84 23.95 41.80 56.20 25.54 44.01 58.91 26.58 47.40 62.45 28.31 48.76 64.63 29.22 51.58 65.18 30.13 52.78 69.17 31.78 53.98 71.81 32.25 56.39 74.57 33.71 58.32 77.95 35.50 60.41 80.48 36.41 61.19 82.16 37.31 63.71 82.79

CHOICE OF TOLERANCE

Size

Decimal Equivalent

25/32

.78125

51/64

.796875

13/16

.8125

53/64

.828125

27/32

.84375

55/64

.859375

49/64

7/8

Length Overall Inches

.765625

6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12 6 9 12

.8750

57/64

.890625

29/32

.90625

59/64

.921875

15/16

.9375

61/64

.953125

31/32

.96875

63/64

.984375

1”

1.0000

+ .0002 – .0000

OR

M2

Net Price Each

26.73 43.38 57.13 27.12 44.80 58.25 28.57 46.01 60.29 29.80 47.24 62.31 30.82 48.36 63.53 31.15 49.48 65.84 32.58 50.91 67.29 33.22 52.61 69.01 33.74 54.42 73.48 34.69 55.55 74.92 35.49 57.19 77.03 36.75 58.40 78.38 37.51 59.63 80.42 38.77 61.25 82.52 40.91 63.16 84.96 42.00 65.05 87.63

M42

Net Price Each

38.93 64.49 84.91 40.29 66.58 86.58 41.64 68.38 89.59 43.44 70.19 92.56 44.93 71.85 94.38 46.78 73.50 97.81 48.92 75.60 99.93 50.49 78.15 102.49 50.63 80.84 109.08 52.04 82.49 111.26 53.27 84.64 114.39 55.12 86.71 116.37 56.21 88.52 119.37 60.17 90.91 122.53 61.15 93.81 126.21 61.96 96.64 130.22

+ .0000 – .0002

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

•

453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 5

DRILL & REAMER BLANKS

FRACTIONAL HUTCHINSON HSS BLANKS

DRILL & REAMER BLANKS

METRIC HUTCHINSON HSS BLANKS METRIC BLANKS - .35mm - 4.70mm DIAMETER M2 HIGH SPEED STEEL - ROCKWELL “C” 62-64 M42 HIGH SPEED STEEL - ROCKWELL “C” 66-68

Diameter mm

.35 .40 .45 .50 .55 .60 .65 .70 .75 .80 .85 .90 .95 1.00 1.05 1.10 1.15 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05

Length Overall mm

38 38 38 38 38 38 38 38 38 38 38 38 38 38 41 44 44 48 48 48 48 48 48 48 48 48 51 51 51 51 51 51 51 51 57

M2

M42

Net Price Each

Diameter mm

Net Price Each

3.31 3.31 3.31 3.31 2.71 2.71 2.71 2.31 2.31 2.07 2.07 2.07 1.91 1.91 1.75 1.75 1.75 1.75 1.75 1.67 1.67 1.67 1.67 1.67 1.67 1.67 1.67 1.67 1.52 1.52 1.52 1.52 1.52 1.52 1.53

2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.60 2.70 2.75 2.80 2.90 3.00 3.10 3.20 3.25 3.30 3.40 3.50 3.60 3.70 3.75 3.80 3.90 4.00 4.10 4.20 4.25 4.30 4.40 4.50 4.60 4.70

4.71 4.71 4.71 4.71 3.81 3.81 3.81 3.27 3.27 2.90 2.90 2.90 2.63 2.63 2.50 2.50 2.50 2.50 2.50 2.39 2.42 2.42 2.42 2.42 2.42 2.42 2.42 2.42 2.28 2.28 2.28 2.28 2.28 2.36 2.37

CHOICE OF TOLERANCE

+ .0051 mm – .0000

Length Overall mm

57 57 57 57 57 57 57 64 64 64 64 70 70 70 70 70 70 70 76 76 76 76 76 76 76 76 83 83 83 83 83 86 86 89 89

OR

M2

Net Price Each

1.53 1.53 1.53 1.53 1.53 1.53 1.58 1.58 1.58 1.58 1.58 1.58 1.58 1.58 1.63 1.63 1.66 1.66 1.66 1.66 1.66 1.66 1.66 1.75 1.75 1.75 1.75 1.75 1.75 1.79 1.79 1.79 1.79 2.05 2.05

+ .0000 – .0051 mm

METRIC BLANKS AVAILABLE .25mm - 35.0mm DIAMETER LENGTHS UP TO 900mm TO SUIT YOUR REQUIREMENTS

WILLIAM T. HUTCHINSON CO.

Page 6

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

M42

Net Price Each

2.37 2.37 2.37 2.37 2.37 2.37 2.47 2.47 2.47 2.47 2.47 2.52 2.52 2.52 2.56 2.56 2.61 2.61 2.61 2.61 2.62 2.62 2.62 2.81 2.81 2.81 2.81 2.81 2.82 2.90 2.90 2.91 2.91 3.39 3.39

METRIC BLANKS - 4.75mm - 13.0mm DIAMETER M2 HIGH SPEED STEEL - ROCKWELL “C” 62-64 M42 HIGH SPEED STEEL - ROCKWELL “C” 66-68

Diameter mm

4.75 4.80 4.90 5.00 5.10 5.20 5.25 5.30 5.40 5.50 5.60 5.70 5.75 5.80 5.90 6.00 6.10 6.20 6.25 6.30 6.40 6.50 6.60 6.70 6.75 6.80 6.90 7.00 7.10 7.20 7.25 7.30 7.40 7.50 7.60

Length Overall mm

89 89 92 92 92 95 95 95 95 95 98 98 98 98 98 102 102 102 102 102 105 105 105 105 105 105 105 108 108 108 108 108 111 111 111

M2

Net Price Each

2.05 2.12 2.43 2.43 2.43 2.43 2.68 2.68 2.68 2.68 2.68 2.68 2.68 2.96 2.96 2.96 2.96 3.12 3.12 3.12 3.52 3.52 3.52 3.52 3.52 3.80 3.80 3.80 3.80 3.80 3.80 3.80 4.06 4.06 4.06

M42

Net Price Each

3.39 3.47 3.95 3.95 3.95 3.96 4.35 4.35 4.35 4.35 4.35 4.35 4.35 4.79 4.79 4.79 4.79 5.12 5.12 5.12 5.89 5.89 5.89 5.89 5.89 6.33 6.33 6.33 6.33 6.37 6.37 6.37 6.80 6.80 6.80

CHOICE OF TOLERANCE

Diameter mm

7.70 7.75 7.80 7.90 8.00 8.10 8.20 8.25 8.30 8.40 8.50 8.60 8.70 8.75 8.80 8.90 9.00 9.10 9.20 9.25 9.30 9.40 9.50 9.60 9.70 9.75 9.80 9.90 10.00 10.50 11.00 11.50 12.00 12.50 13.00

+ .0051 mm – .0000

Length Overall mm

114 114 114 114 114 117 117 117 117 121 121 121 121 124 124 124 124 124 127 127 127 127 127 130 130 130 130 130 130 133 140 142 149 152 152

OR

M2

Net Price Each

4.45 4.45 4.45 4.45 4.45 4.91 4.91 4.91 4.91 4.91 5.40 5.40 5.82 5.82 5.82 5.82 5.82 5.82 6.27 6.27 6.27 6.28 6.28 6.82 6.82 6.84 6.84 6.84 6.84 7.52 8.69 9.57 10.08 12.15 14.01

M42

Net Price Each

7.57 7.57 7.57 7.57 7.57 8.18 8.18 8.18 8.18 8.18 9.02 9.02 9.71 9.81 9.81 9.81 9.81 9.81 10.75 10.75 10.75 10.76 10.76 11.72 11.72 11.74 11.74 11.74 11.74 12.92 14.86 15.90 16.78 18.61 23.51

+ .0000 – .0051 mm

SPECIALLY EQUIPPED FOR SMALL LOT, HIGH PRECISION CENTERLESS GRINDING

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

• 453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 7

DRILL & REAMER BLANKS

METRIC HUTCHINSON HSS BLANKS

DRILL & REAMER BLANKS

HIGH SPEED STEEL DRILL BLANKS 36 INCH HSS LENGTHS

HARDENED, GROUND HSS DRILL BLANKS HAVE A HARDNESS OF R/C 62-64

TOLERANCE + .001

FRACTIONAL SIZE DRILL RODS

1/16 5/64 3/32 7/64 1/8 9/64 5/32 11/64 3/16 13/64 7/32 15/64 1/4 17/64 9/32 19/64 5/16 21/64 11/32 23/64 3/8 25/64 13/32 27/64 7/16 29/64 15/32 31/64 1/2 17/32 9/16 5/8 11/16 23/32 3/4 7/8 1 1 1/8

DECIMAL EQUIVALENT

.0625 .0781 .0938 .1094 .1250 .1406 .1562 .1719 .1875 .2031 .2188 .2344 .2500 .2656 .2812 .2969 .3125 .3281 .3438 .3594 .3750 .3906 .4062 .4219 .4375 .4531 .4688 .4844 .5000 .5312 .5625 .6250 .6875 .7188 .7500 .8750 1.0000 1.1250

ANNEALED M2 HIGH SPEED BLANKS–36”

7.17 7.68 8.19 8.64 9.48 10.50 11.64 12.81 13.77 15.06 16.41 17.55 19.11 20.85 22.56 24.48 26.52 28.50 30.72 32.64 34.89 37.35 39.78 42.45 45.24 47.94 50.01 53.97 56.97 63.36 70.41 82.77 98.79 107.22 116.04 155.22 200.34 265.60

ALL BLANKS CAN BE CUT TO MEET YOUR REQUIREMENTS.

HARDENED GROUND HIGH SPEED BLANKS–36”

19.18 20.71 20.80 22.86 23.97 24.11 24.26 25.44 25.62 26.69 26.91 28.03 29.28 32.42 32.70 34.28 34.60 39.26 41.61 43.82 44.19 50.94 51.15 54.09 56.13 57.13 59.60 61.26 63.76 161.78 171.18 185.44 209.02 215.38 220.38 245.74 275.46 370.02

PRECISION GRINDING AVAILABLE TO A .0002 TOLERANCE

36 INCH HARDENED & GROUND HSS LENGTHS

METRIC SIZE

WIRE SIZE

TOLERANCE +.0000 -.0005

TOLERANCE + -.0003

Wire Decimal Size Equiv. 61 .0390 62 .0380 63 .0370 64 .0360 65 .0350 66 .0330 67 .0320 68 .0310 69 .0292 70 .0280 71 .0260 72 .0250 73 .0240 74 .0225 75 .0210 76 .0200 77 .0180 78 .0160 79 .0145 80 .0135

Price Each 20.90 20.90 20.90 20.90 21.18 21.18 21.18 21.38 21.38 21.38 21.96 21.96 21.96 22.53 22.53 22.53 22.96 22.96 23.47 23.47

Metric Decimal Price Size Equiv. Each .50mm .0199 22.53 .60 .0236 21.96 .70 .0276 21.38 .80 .0315 21.38 .90 .0354 21.18 1.00 .0394 20.90 1.10 .0433 20.90 1.20 .0472 20.04 1.30 .0512 20.04 1.40 .0551 20.04 1.50 .0591 19.18 1.60 .0630 19.18 1.70 .0669 19.18 1.80 .0709 20.71 1.90 .0748 20.71 2.00 .0787 20.71 2.10 .0827 20.80 2.20 .866 20.80 2.30 .0906 20.80 2.40 .0945 22.86 2.50 .0984 22.86

24 INCH  HARDENED & GROUND HSS LENGTHS Diameter Inches 17/32 9/16 5/8 11/16 23/32 3/4 13/16 7/8 1

TOLERANCE + - .001

Decimal Equivalent .5312 .5625 .6250 .6875 .7188 .7500 .8125 .8750 1.0000

WILLIAM T. HUTCHINSON CO.

Page 8

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

Price Each

97.00 111.75 116.50 140.75 148.50 156.50 177.00 182.00 208.00

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

DRILL & REAMER BLANKS / CUTTING TOOLS

HSS DRILL BLANK & DRILL SETS

Conveniently packaged in all steel indexes, sets of general purpose jobber length drills and precision ground drill or reamer blanks are available for shipment from our plant. +.0002 Please specify when ordering: Drill set / Drill blank ( +.0000 -.0002 ) set / Reamer Blank ( -.0000 ) set DRILL SET

LETTER SET “A” - “Z” 26 PIECES

95.35

WIRE SET #1 - #60 60 PIECES

WIRE SET #61 - #80 20 PIECES

FRACTIONAL SET 1/16” - 1/2” x 1/64ths 29 PIECES

FRACTIONAL SET 1/16” - 1/2” x 1/32nds 15 PIECES

M2 HSS BLANK INDEX SET ONLY 121.59

9.45

81.90

103.89

7.45

29.00

49.34

4.95

110.30

136.98

8.65

59.60

74.25

7.10

METRIC BLANKS AVAILABLE AS DRILL BLANKS( +.0000 -.0051 MM )OR REAMER BLANKS ( +.0051 -.0000 MM )

METRIC SETS

OTHER SETS AVAILABLE TO SUIT YOUR NEEDS - CALL FOR PRICING AND DELIVERY

1 mm. - 6mm. x 1/2 mm. 11 PIECES

1 mm. - 13mm. x 1/2 mm. 25 PIECES 1 mm. - 5.9 mm. x .1 mm. 50 PIECES 6 mm. - 10 mm. x .1 mm. 41 PIECES

DRILL SET

M2 HSS BLANK INDEX SET ONLY 27.73

6.15

99.30

132.43

8.65

75.45

104.63

9.65

178.40

220.79

22.95

19.75

115 PIECES - COMPLETE IN ONE BOX

INCLUDES: WIRE SET #1 - #60, LETTER SET “A” - “Z”, 1/16” - 1/2” x 1/64ths

DRILL SET

297.15

M2 HSS BLANK SET 371.56

INDEX ONLY 34.65

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

• 453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 9

DRILL & REAMER BLANKS

36" LONG AIR HARDENING DRILL RODS Size 1/16 5/64 3/32 7/64 1/8 9/64 5/32 11/64 3/16 13/64 7/32 15/64 1/4 17/64 9/32 19/64 5/16 21/64 11/32 23/64 3/8 25/64 13/32 27/64 7/16 29/64 15/32 31/64 1/2 17/32 9/16 19/32 5/8 21/32 11/16 23/32 3/4 13/16 7/8 1 1-1/16 1-1/8 1-1/4 1-3/8 1-1/2 1-3/4 2

Decimal .0625 .0781 .0937 .1094 .1250 .1406 .1562 .1719 .1875 .2031 .2187 .2344 .2500 .2656 .2812 .2969 .3125 .3281 .3437 .3594 .3750 .3906 .4062 .4219 .4375 .4531 .4687 .4844 .5000 .5312 .5625 .5937 .6250 .6562 .6875 .7187 .7500 .8125 .8750 1.0000 1.0625 1.1250 1.2500 1.3750 1.5000 1.7500 2.0000

AISI TYPE A2

Price 2.21 3.80 3.56 4.26 3.91 5.49 5.56 6.71 5.94 7.68 8.27 9.50 8.13 9.06 10.17 11.37 10.49 12.79 14.00 15.31 14.93 17.87 19.34 20.87 20.32 24.04 25.77 27.51 25.45 32.25 32.19 39.59 39.28 47.86 47.55 57.45 56.14 65.88 76.41 99.19 111.99 125.54 145.09 175.61 207.21 281.99 365.51

Size 2mm 3mm 4mm 5mm 6mm 7mm 8mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm 21mm 22mm 23mm 24mm 25mm

Decimal .0787 .1181 .1575 .1969 .2362 .2756 .3150 .3543 .3937 .4331 .4724 .5118 .5512 .5906 .6299 .6693 .7087 .7480 .7874 .8268 .8661 .9055 .9449 .9843

AISI TYPE D2

Size 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 1 1/8 1 1/4 1 1/2 1 3/4 2

Price 5.95 8.82 10.52 11.37 15.17 15.33 18.89 22.96 28.19 35.04 40.48 46.88 54.36 61.88 68.49 78.14 88.01 95.72 111.78 118.33 129.88 139.26 153.83 166.88

Decimal .1250 .1875 .2500 .3125 .3750 .4375 .5000 .6250 .7500 .8750 1.0000 1.1250 1.2500 1.5000 1.7500 2.0000

DRILL ROD IS NOT HEAT TREATED

DRILL ROD TOLERANCES Diameter Tolerance ± .0003 Below .124 ± .0005 .125-1.500 ± 1.500-2.000 .001 TYPICAL ANALYSIS OF DRILL ROD MATERIALS C Si Mn W Cr V Mo S7 .50 .25 .75 3.25 1.40 D2 1.50 .30 .30 12.00 .90 .75 A2 1.00 .30 .75 5.00 .25 1.00 01 .94 .30 1.20 .50 .50

AISI TYPE S7

Price 21.17 17.30 24.30 33.47 46.52 63.44 79.43 120.20 173.10 235.39 295.81 372.84 509.50 732.40 713.47 904.88

Size

1/16 3/32 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 1 1/4 1 3/8 1 1/2 1 3/4 2

Page 10

•

( 908) 688-0533

•

.0625 .0937 .1250 .1562 .1875 .2187 .2500 .3125 .3750 .4375 .5000 .6250 .7500 .8750 1.0000 1.2500 1.3750 1.5000 1.7500 2.0000

4.47 6.51 7.97 10.35 12.28 14.22 15.96 18.82 25.74 35.01 37.08 56.31 81.12 110.42 140.53 219.58 265.67 316.16 430.36 562.64

PRECISION GRINDING OF DRILL ROD AVAILABLE TO A .0002 TOLERANCE. ALSO AVAILABLE IN LIMITED SIZES: AISI TYPE W1 CALL FOR PRICING AND DELIVERY.

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

Price

ALL DRILL ROD CAN BE CUT AND HEAT TREATED TO MEET YOUR REQUIREMENTS.

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

Decimal

Size 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38

NUMBER & LETTER SIZES

Decimal Price Size Decimal Price

Size 1/16 5/64 3/32 7/64 1/8 9/64 5/32 11/64 3/16 13/64 7/32 15/64 1/4 17/64 9/32 19/64 5/16 21/64 11/32 23/64 3/8 25/64 13/32 27/64 7/16

.039 .040 .041 .042 .045 .050 .055 .058 .063 .066 .069 .072 .075 .077 .079 .081 .085 .088 .092 .095 .097 .099 .101

8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 1.59 1.73 1.87 2.06 2.23 2.38 2.48 2.61 2.81 3.07 3.38 1.83 1.89 2.00 2.13

37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15

Decimal Price .0625 $1.45 .0781 2.43 .0937 1.74 .1094 2.43 .1250 2.22 .1406 2.98 .1563 2.79 .1719 3.63 .1875 3.21 .2031 4.05 .2188 3.84 .2344 4.76 .2500 3.65 .2656 4.43 .2813 4.59 .2969 5.49 .3125 4.59 .3281 6.00 .3438 6.08 .3594 7.19 .3750 6.47 .3906 8.28 .4062 8.40 .4219 9.64 .4375 8.77

.103 .106 .108 .110 .112 .115 .120 .127 .134 .139 .143 .146 .148 .151 .153 .155 .157 .161 .164 .168 .172 .175 .178

2.15 2.30 2.38 2.45 2.52 2.69 2.92 2.43 2.69 2.92 3.09 3.23 3.78 3.43 3.56 3.58 3.03 3.21 3.31 3.48 3.64 3.75 3.90

Size Decimal Price 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D F G H I J

.180 .182 .185 .188 .191 .194 .197 .199 .201 .204 .207 .212 .219 .227 .234 .238 .242 .246 .257 .261 .266 .272 .277

FRACTIONAL SIZES Size 29/64 15/32 31/64 1/2 33/64 17/32 35/64 9/16 37/64 19/32 39/64 5/8 41/64 21/32 43/64 11/16 45/64 23/32 47/64 3/4 49/64 25/32 51/64 13/16 53/64

Decimal .4531 .4688 .4844 .5000 .5156 .5313 .5469 .5625 .5781 .5938 .6094 .6250 .6406 .6563 .6719 .6875 .7031 .7188 .7344 .7500 .7656 .7813 .7969 .8125 .8281

Price 11.14 11.11 12.73 10.78 13.58 14.03 15.27 15.06 17.08 17.57 18.74 16.66 20.69 21.16 22.76 22.21 24.93 25.38 27.18 23.44 28.93 29.36 31.31 30.31 33.86

4.00 4.05 4.21 3.48 3.57 3.73 3.84 3.87 3.96 4.12 4.19 4.43 4.16 4.46 4.73 4.93 5.06 5.21 4.12 4.25 4.43 4.63 4.80

Size Decimal K .281 L .290 M .295 N .302 O .316 P .323 Q .332 R .339 S .348 T .358 U .368 V .377 W .386 X .397 Y .404 Z .413

Size Decimal Price 27/32 .8438 34.26 55/64 .8594 36.43 7/8 .8750 35.13 57/64 .8906 39.15 29/32 .9063 39.51 59/64 .9219 41.93 15/16 .9375 42.26 61/64 .9531 44.82 31/32 .9688 45.14 63/64 .9844 47.79 1 1.0000 39.67 1-1/16 1.0625 51.63 1-3/32 1.0938 54.44 1-1/8 1.1250 55.28 1-3/16 1.1875 64.52 1-1/4 1.2500 64.77 1-5/16 1.3125 74.79 1-3/8 1.3750 78.36 1-7/16 1.4375 89.76 1-1/2 1.5000 92.34 1-9/16 1.5625 99.56 1-5/8 1.6250 113.50 1-3/4 1.7500 125.69 1-7/8 1.8750 151.14 2 2.0000 162.83

Price 4.94 5.24 5.44 5.71 5.59 5.78 6.13 6.41 6.71 7.11 7.53 7.72 8.10 8.58 8.87 9.26

MILLIMETER SIZES Size Decimal Price .0787 2.98 2mm 3mm .1181 3.45 4mm .1575 3.77 5mm .1969 4.73 6mm .2362 6.50 7mm .2756 5.84 8mm .3150 7.02 9mm .3543 8.45 10mm .3937 10.34 11mm .4331 12.73 12mm .4724 14.63 13mm .5118 16.66 14mm .5512 19.30 15mm .5906 22.08 16mm .6299 24.28 17mm .6693 27.81 18mm .7087 31.26 19mm .7480 33.89 20mm .7874 37.53 21mm .8268 41.50 22mm .8661 45.51 23mm .9055 48.34 24mm .9449 54.01 25mm .9843 58.64

DRILL ROD TOLERANCES Diameter Tolerance ± .0003 Below .124 ± .0005 .125-1.500 ± .001 1.500-2.000

DRILL ROD IS NOT HEAT TREATED ALL DRILL ROD CAN BE CUT AND HEAT TREATED TO MEET YOUR REQUIREMENTS. PRECISION GRINDING OF DRILL ROD AVAILABLE TO A .0002 TOLERANCE. ALSO AVAILABLE IN LIMITED SIZES: AISI TYPE W1 CALL FOR PRICING AND DELIVERY.

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

• 453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 11

DRILL & REAMER BLANKS

36" LONG AISI 0-1 OIL HARDENING DRILL RODS

DRILL & REAMER BLANKS

HUTCHINSON SUPER HIGH ALLOY BLANKS ASP30 (8.5% COBALT) T15PM (12% TUNGSTEN) ASP60 (10.5% COBALT) M4PM (5.75 TUNGSTEN) ASP23 (AISI M3:2) CPM10V (AISI  A11)(9.75% VANADIUM) Diameter Inches

Decimal Equivalent

Length Overall Inches

3/32

.09375

2 1/2

1/16 1/8

3/16 1/4

.0625 .1250 .1875 .2500

2 1/2 2 1/2 4 6

2 1/2 4 6

2 1/2 4

4.72 6.80 3.81 5.83 9.21 5.02

7/16

.4375

6 4

6

5/8

.6250

4

3/4

.7500

4

7/8

.8750

6

6 6

6

Net Price Net Price Each Each

—

4.30

—

3.06

—

4.15

—

4.17

—

6.01

— — 7.33

Net Price Each

Net Price Each

—

4.07

—

— — — —

3.55

11.87

8.03

28.97

5.10

—

Net Price Each

4.34

18.91 11.51

4.21

—

3.01

4.69

5.89

11.20

4.96

7.04

4.09 3.75

4.99

7.87

11.41

4.25

6.48

17.08

6.33

10.00

9.66

14.06

8.33

21.86

8.13

13.37

11.83

16.89

10.04

26.33

9.81

16.28

22.92 18.55 25.89 31.57 42.49

9.97

19.78

11.71

25.35

15.05

32.77 26.60 37.28 43.49 60.40

39.50

14.71

24.40

15.66

40.88

15.31

24.18

26.59

69.69

25.98

39.23

19.58 21.90 35.86

74.67

106.30 63.17

92.64

35.33 48.70

132.46 78.62

CHOICE OF  TOLERANCE

15.05

11.45

59.44 82.00

9.76

30.67

41.89 57.58

26.33

+.0002 -.0000

—

57.01 93.73

19.74

21.38 35.04

92.41

34.54

—

—

126.98 47.56 207.83

OR

—

ASP23 An all around steel suitable for cutting tools such as reamers, taps, milling cutters, broaches, etc. . . Used where cutting conditions demand high wear resistance and superior toughness but where demands for hot hardness are not paramount. ASP23 is also suitable for cold work applications where tools for punching show an admirable combination of wear resistance and toughness.

6.25

10.92

16.79

M4PM is designed for high wear resistance. Its high vanadium and carbon content provide high resistance to wear in cold work and cutting applications. It exhibits improved performance working with abrasive materials. Manufactured powder-metallurgically for improved grindability and toughness.

7.46

7.47

17.74

4

1.0000

3.46

6

.3750

1

4.67

13.57

3/8

.5000

4.99

6

4

1/2

Net Price Each

11.50

.3125

T15PM is a tungsten type high speed steel containing high carbon and vanadium for very high hardness and maximum wear resistance, and cobalt for good red hardness. Manufactured powder—metallur gi cally for improved quality and grindability.

ASP30 T15PM M4PM ASP60 ASP23 CPM10V

6

5/16

ASP30 is an 8.5% cobalt content high-alloy high-speed steel man u factured powdermetallurgically. This high performance material exhibits good grindability, tough ness, hot hardness and wear resistance.

20.05

ASP60 is an extremely high alloy high speed steel. The steel is atomized, compacted and processed to required dimensions. The result is an extremely homogeneous steel. ASP 60’s homogeneous structure enhances such properties as dimensional stability and shape during heat treatment, as well as improving grindability and toughness. ASP-60’s method of manufacture and composition mean that it can provide high hot hardness and good wear resistance.

—

36.03 58.84

CPM10V(AISI  A11) is a unique tool steel made by a particle metallurgy process. Its high carbon and high vanadium content provides a combination of exceptionally good wear resistance, toughness and strength for both cold and warm work applications.

53.41

79.85

104.77

134.58

+.0000 -.0002

TYPICAL ANALYSIS OF SUPER HIGH ALLOY MATERIALS:

AVAILABLE IN ANY DIAMETER .0300 - 1.000 ADDITIONAL LENGTHS AVAILABLE TO SUIT YOUR REQUIREMENTS

ASP30 T15PM M4PM ASP60 ASP23 CPM10V

C 1.28 1.55 1.35 2.30 1.28 2.45

Cr 4.2 4.0 4.0 4.0 4.2 5.25

Mo 5.0 — 4.5 7.0 5.0 1.3

WILLIAM T. HUTCHINSON CO.

Page 12

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

W 6.4 12.0 5.75 6.5 6.4 —

V Co 3.1 8.5 5.0 5.0 4.0 — 6.5 10.5 3.1 — 9.75 —

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

Hardness R/C 65-67 R/C 64-66 R/C 63-65 R/C 67-69 R/C 63-65 R/C 62-64

DRILL & REAMER BLANKS

WKE 45 SUPER COBALT HSS BLANKS WKE 45 WITH 11% COBALT CONTENT, FINE GRAIN STRUCTURE AND UNIQUE CHEMICAL COMPOSITION, MEETS REQUIREMENTS FOR MAXIMUM PERFORMANCE IN MOST CUTTING TOOL APPLICATIONS Dia. mm 3 4 4 5 5 6 6 6 6 8 8 8 10 10 10 12 12 12 14 15 16 16 16 18 18 20

METRIC Length Overall mm 100 80 100 100 160* 63* 80* 100 160 100 160 200 100 160 200* 100 160 200* 160 100* 100* 160* 200* 100* 200* 200

Net Price Each 13.22 10.82 13.83 14.85 18.76 8.47 10.76 16.23 21.66 19.08 26.66 32.11 24.18 35.53 85.68 29.27 51.82 59.75 59.68 44.72 45.37 71.36 87.40 55.78 106.53 117.45

FRACTIONAL

Dia. Inches 1/8 3/16 3/16 1/4 1/4 1/4 5/16 5/16 5/16 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 3/4 3/4

Length Overall Inches 4 2 1/2 4 2 1/2* 4 6 4 6 9/32 8* 4 6 8* 4 6 8 4* 6 6 8*

HARDNESS: R/C 67-69

Net Price Each 9.36 8.08 11.59 9.55 14.63 22.45 19.74 28.25 32.72 24.53 30.96 41.21 35.44 48.15 64.67 46.75 74.22 94.45 159.32

STANDARD DIAMETER TOLERANCE + .0 – .002”

SPECIAL DIAMETERS AND TOLERANCES AVAILABLE–PRICES UPON REQUEST WKE45 SQUARE & RECTANGULAR TOOLBITS AVAILABLE SEE PAGE 41

WKE45 TYPICAL ANALYSIS C 1.40

Cr 4.2

Mo 3.5

W 9.0

V 3.5

*

Co 11.0

AVAILABLE UNTIL STOCK IS EXHAUSTED

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

• 453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 13

ENGRAVING BLANKS

ENGRAVING BLANKS

SPLIT HALF-ROUND

Solid Tungsten Carbide

Solid Tungsten Carbide Blanks with a close sub-micron grain structure, hardness of RA91.8 and high transverse rupture strength offer superior results when machining both ferrous and non ferrous metals as well as plastics, fiberglass and mylar.

SINGLE END

DIAMETER

O.A.L.

1/8 1/8 1/8 1/8 1/8 3/16 3/16 3/16 3/16 3/16 1/4 1/4 1/4 1/4 1/4 5/16 5/16 5/16 5/16 3/8 3/8 3/8 3/8 7/16 7/16 7/16 7/16 1/2 1/2 1/2

1-1/2 2 3 4 6 2 2-1/2 3 4 6 2 2-1/2 3 4 6 2-1/2 3 4 6 2-1/2 3 4 6 2-1/2 3 4 6 3 4 6

DOUBLE END

LENGTH OF SPLIT/FLAT 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8

SINGLE END PRICE EA. 5.47 6.67 8.35 11.64 19.08 8.55 9.43 12.38 17.27 24.44 11.25 11.96 16.23 22.74 33.26 17.67 26.97 34.78 48.68 23.13 30.84 41.45 60.89 24.41 30.84 41.45 60.89 44.91 59.04 98.24

DOUBLE END PRICE EACH 8.83 9.44 10.85 17.84 23.62 12.34 13.22 15.58 20.49 29.54 15.79 17.40 19.77 26.27 38.40 22.49 31.98 37.27 54.22 29.16 36.80 46.76 67.40 31.79 36.80 46.76 67.40 52.13 66.26 107.16

Tolerances: Diameter +.0 Split/Flats +.001 above centerline –.0005 –.0 END SHAPES AVAILABLE ON REQUEST - 6PC. MINIMUM PER ITEM

INFORMATION AND PRICING AVAILABLE ON REQUEST ALSO AVAILABLE IN BOXED SETS

WILLIAM T. HUTCHINSON CO.

Page 14

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

DRILL & REAMER BLANKS

CARBIDE DRILL BLANKS CENTERLESS GROUND - CUT TO LENGTH Dia.

1/16 3/32 1/8 5/32 3/16 1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1 1 1/4 Dia.

Decimal

.0625 .09375 .1250 .15625 .1875 .2500 .3125 .3750 .4375 .5000 .5625 .6250 .7500 .8750 1.0000 1.2500

11⁄2 2 3.48 — 2.34 3.00 1.16 1.93 5.21 2.99 2.82 3.44 5.90 6.87 — 9.27 7.49 12.17 — — — 16.40 — — — — — — — — — — — —

METRIC SIZES

3mm 4 5 6 6 8 10 10 12 14 16 18 20 25

Length 39mm 51 51 51 64 64 70 100 76 84 89 100 100 100

21⁄2 — 3.19 2.15 3.75 4.32 8.51 11.19 13.61 17.03 21.32 — — — 89.67 — —

LENGTH 3 31⁄2 4 5 6 3.23 — — — 8.77 2.39 — — — 10.20 3.49 — 4.65 — 10.68 — — — — 13.57 5.17 — 6.99 — 19.33 10.53 13.36 12.41 — 23.24 12.26 17.26 19.29 — 34.90 16.14 20.09 23.63 — 38.13 21.51 27.10 28.04 — 42.19 25.55 29.81 35.74 40.55 55.45 — 44.14 — — 73.69 40.11 46.78 57.27 73.52 88.23 71.37 77.75 76.45 96.21 116.65 — — 109.75 — 178.96 — — 126.69 165.95 201.74 — — 256.21 — —

12 16.07 16.39 18.12 22.37 30.81 47.79 74.67 99.27 127.00 158.83 201.02 248.16 285.89 389.11 361.91 —

C2 Micrograin Carbide 10% Cobalt Content Hardness R/A 91.8 TRS (nominal) 410 KPSI Density 14.50 Gm/CC

Price

1.47 4.30 4.61 5.53 7.81 11.81 18.06 28.06 25.76 38.49 53.47 87.47 100.57 132.09

Diameter Tolerance +.0 -.0005

STYLE STB 1000 & 2000 BLANKS AVAILABLE SEE PAGES 44 & 45

Additional grades and tolerances available on application Available in any diameter 1⁄64"-3" – lengths up to 30" WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

•

453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 15

DRILL & REAMER BLANKS

HARDENED & GROUND TOOL STEEL BLANKS SIX INCH LENGTHS

HEAT TREATED & GROUND TO A DIAMETER TOLERANCE OF +.0000 -.0003

SEE PAGE 10 FOR TYPICAL CHEMICAL ANALYSIS OF THESE MATERIALS

DIAMETER 1/16

5/64

3/32

7/64 1/8

5/32

3/16

7/32 1/4

9/32

5/16

11/32 3/8

7/16 1/2

9/16 5/8

3/4

7/8 1”

MATERIAL

DECIMAL EQUIV. .0625

.078125 .09375

.109375 .1250

.15625

AISI O1 R/C 60-62 Net Price Each $5.71

5.57

5.71

5.23

5.38

.3750

13.00

7.68

10.95

15.83

9.17

13.01

18.48

9.02

10.89

12.97

.5625

15.83

19.79

.6250

14.80

18.89

.7500

22.92

24.78

.8750

30.44

33.30

1.0000

42.81

41.34

7.80

9.71

7.39

12.18

5.14

8.52

11.09

.4375

.5000

5.88

6.76

6.43

8.07

$10.05

10.08

6.19

7.89

$5.83

5.69

5.40

6.82

.34375

9.03

5.63

6.72

.3125

5.59

5.38

6.01

.28125

5.44

5.07

5.74

.2500

AISI D2 R/C 60-62 Net Price Each

5.58

5.18

.21875

AISI S7 R/C 58-60 Net Price Each

$5.49

5.51

.1875

AISI A2 R/C 58-60 Net Price Each

50.90

6.02

7.07

8.42

10.64

16.77

16.18 —

25.16

34.22

46.38

57.79

8.04

9.05

11.35

14.80

25.92

24.65 —

37.94

52.62

71.37

88.84

AVAILABLE IN SPECIAL LENGTHS, DIAMETERS, HARDNESS & TOLERANCES TO MEET YOUR REQUIREMENTS CALL FOR PRICING & DELIVERY

WILLIAM T. HUTCHINSON CO.

Page 16

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com

DRILL & REAMER BLANKS

HARDENED & GROUND TOOL STEEL BLANKS TWELVE INCH LENGTHS

HEAT TREATED & GROUND TO A DIAMETER TOLERANCE OF +.0000 -.0003

SEE PAGE 10 FOR TYPICAL CHEMICAL ANALYSIS OF THESE MATERIALS

DIAMETER 1/16

5/64

3/32

7/64 1/8

5/32

3/16

7/32 1/4

9/32

5/16

11/32 3/8

7/16 1/2

9/16 5/8

3/4

7/8 1”

DECIMAL EQUIV. .0625

.078125 .09375

MATERIAL

AISI O1 R/C 60-62

AISI A2 R/C 58-60

AISI S7 R/C 58-60

AISI D2 R/C 60-62

Net Price Each

Net Price Each

Net Price Each

Net Price Each

$14.51

$14.19

$15.55

9.45

9.37

12.55

14.16

14.07

.109375

10.21

10.05

.15625

10.91

11.46

.1250

.1875

.21875 .2500

.28125 .3125

.34375 .3750

.4375

.5000

.5625

.6250

.7500

.8750

1.0000

10.59

10.33

10.62

10.84

11.94

11.99

10.96

12.27

13.35

15.75

12.24

15.20

14.84

21.45

23.86

29.96

37.07

46.59

61.05

76.97

14.17

16.56

18.26

26.90

30.49

40.22

45.43

59.32

83.05

92.25

15.55

$24.79

22.88

19.38

12.08

18.69

13.62

23.57

14.59

19.48

15.21

24.30

15.27

20.22

21.18

29.06

17.90

25.23

25.32

36.32

23.47

33.86

30.40

42.32

37.13

57.71

36.58

56.27

—

—

55.94

73.44

99.57

130.47

85.32

116.51

158.08

197.34

AVAILABLE IN SPECIAL LENGTHS, DIAMETERS, HARDNESS & TOLERANCES TO MEET YOUR REQUIREMENTS CALL FOR PRICING & DELIVERY

WILLIAM T. HUTCHINSON CO.

TOLL FREE 1-800-544-7934

• 453 LEHIGH AVENUE

www.hssblanks.com

• UNION, NEW JERSEY 07083-7926

Page 17

DRILL & REAMER BLANKS

HARDENED & GROUND 440C STAINLESS STEEL BLANKS SIX & TWELVE INCH LENGTHS

HEAT TREATED TO R/C 58-60 & GROUND TO A DIAMETER TOLERANCE OF +.0000 -.0003 DIAMETER 1/16

5/64

3/32

7/64 1/8

5/32

3/16

7/32 1/4

9/32

5/16

11/32 3/8

7/16 1/2

9/16 5/8

3/4

7/8 1”

DECIMAL EQUIV.

6” LONG

12” LONG

Net Price Each

Net Price Each

.0625

$16.42

$35.38

.09375

12.42

27.38

.078125 .109375 .1250

.15625

14.42

31.38

10.42

23.38

13.21

29.11

14.44

.1875

30.94

15.03

.21875

30.09

11.03

.2500

19.82

.3125

17.96

.28125

22.09

41.22

15.82

.34375

33.22

36.16

13.96

.3750

28.16

19.87

.4375

41.67

22.18

.5000

46.68

25.43

.5625

50.10

34.17

.6250

71.24

37.00

.7500

76.51

43.92

.8750

87.50

56.37

1.0000

111.72

63.36

125.71

HEAT TREATED 440C IS ONE OF THE HARDEST STAINLESS STEELS. IT IS MAGNETIC AND HAS GOOD WEAR RESISTANCE DUE TO HIGH CARBON CONTENT AVAILABLE IN SPECIAL LENGTHS, DIAMETERS, HARDNESS & TOLERANCES TO MEET YOUR REQUIREMENTS CALL FOR PRICING & DELIVERY

WILLIAM T. HUTCHINSON CO.

Page 18

TOLL FREE 1-800-544-7934

•

( 908) 688-0533

•

FAX ( 908) 688-8296 • ESTABLISHED 1927

www.hssblanks.com