11. LASHING SYSTEMS

LASHING SYSTEMS ANTI-SLIP MATS CAR LASHING / WINCHES TRACK LASHING LASHING BRACES CARGO AND ROPE NETS LASHING STRAP LASHING CHAINS LOAD BINDERS LASHING CHAIN ENDS CARGO TRACKS LOAD SUPPORTING LASHING POINTS

11

INSTRUCTIONS FOR CARGO SECURING

The regulations regarding the lashing of cargo in road transport in Finland differ from those in the rest of the EU region. In Finland, the regulation is decision 940/82 of the Finnish Transport Agency. On other parts of the EU region, a so-called LASHING CAPACITY is in effect. It is calculated with metal parts’ safety factor 2.0 and that of textile parts 3.0. Then, the LC value with, for example, 2,000kg nominal strength lashing is 1,700kg, which is expressed in Dekanewton, i.e. 1,700 daN. The LC value of a lashing with a nominal strength of 3,500kg in Finland, is only 2,500kg or 2,500daN.

LOAD PLACING Distribute the load equally length- and widthwise.

Pay attention to weight distribution.

Support the load against the front wall.

Mass centre down.

Support after partial unloading.

Pay attention to weight distribution.

ATTRITION / LASHING CAPACITY The The amount amount ofof friction friction force force depends depends onon the the roughness roughness ofof contact contact surfaces surfaces and and the the weight weight ofof the the load. load. It It is is weakened weakened significantly significantly byby ice, ice, impurities impurities and and dampness. dampness. The The size size ofof contact contact surface surface areas areas does does not not affect affect friction friction force. force. pallet

friction coefficient

dry damp snowy

Vehicle load weight = 8t Friction coefficient between load and pallet - 0.2 Friction force (0.2×8t) ≈ 1.6t (16kN) In addition to friction, the following securing requirements should be met: — forward 8t — 1.6t = 6.4t (64kN) — sideways 4t — 1.6t = 2.4t (24kN) — backward 4t — 1.6t = 2.4t (24kN) 8 tonnes

LASHING CAPACITY Direction of motion

Example:

Sling t

Friction coefficient = 0.2 0.2 x 16t ≈ 3t

Total t

Requirement t (kN)

Forward ≤ 60° 4 x 3.5t Sideways=90° 0.25 x 6 x 3.5t Backward ≤ 60° 2 x 3.5t

11 - 1

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

INSTRUCTIONS FOR CARGO SECURING

LOADING SECURING

Decision 940/82 of the Finnish Transport Agency APPLIES TO

● trucks ● truck trailers, when the total weight is over 3.5t

The load must be secured in a way that it will endure ● the forward weight of the entire load ● half of the load weight sideways and backwards

LASHING ANGLE When the lashing device is in a horizontal position, the biggest holding force can be achieved. In practice, the lashing force can be calculated according to the below table.

Angle of the lashing device

Lashing force % of the nominal strength

EXAMPLES OF CONSTRUCTION MACHINES Heavy plate bundles.

Tempered chain Ø 10mm (3/8”). If lashing webbings are used, corner protectors must also be used.

Paper rolls

Concrete links

Wedge wood height - 1/5 of the link radius.

TRANSPORTATION OF CONSTRUCTION MACHINES 1. Switch to the parking brake and to a small gear. 2. No machine part should rely merely on hydraulics. Dislocation during a journey must be prevented with a cylinder lock or other appropriate mechanic device. 3. Bind to a rigid or heavy axle.

Prevent the device from moving sideways!

TRANSPORTATION OF CONTAINERS In the transportation of containers, a vehicle equipped with container locks must primarily be used.

Container lock

If a container cannot be locked with container locks, it must be bound with at least four separate bindings.

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 2

11

LASHING SYSTEMS

All lashing system available as 1- and 2 part models, also in dimensions of customer choice and in accordance with endings (page 11-7). Manufactuing in our own sewing shop in Finland All Haklift lashing systems are in accordance with EU standard EN 12195-1 with their LC values

STRUCTURE OF RATCHET TIE DOWNS Long part

Ratchet buckle Short part

2-part with hooks

1-part without hooks

LASHING SYSTEM LC 400 KG ECONOMY

• • • • • • •

for light lashing in trailers, roof racks etc. length 0,4 + 4,6 m standard end fitting steel double J-hooks webbing width 25 mm webbing material 100 % polyester packed in plastic bag with handle and bar code package size 50 psc / pack

LASHING SYSTEM LC 400 KG

• • • • • • • •

Product code: SV100052EC

Product code: SV100052

LASHING SYSTEM LC 1000 KG

• • • • • • • •

for light lashing in vans length 0,5 + 5,5 m standard end fittings steel double J-hooks webbing width 35 mm webbing material 100 % polyester buckle and hooks also available in stainless steel standard lashing packed in plastic bag with handle package size 25 psc / pack

LASHING SYSTEM LC 1700 KG

• • • • • • • •

Product code: SV150062

for light lashing in trailers, roof racks etc. length 0,4 + 4,6 m standard end fitting steel double J-hooks webbing width 25 mm webbing material 100 % polyester packed in plastic bag with handle and bar code buckle and hooks also available in stainless steel package size 50 psc / pack

for normal lashing in trucks length 0,5 + 9,5 m standard end fittings double J-hooks webbing width 50 mm webbing material 100 % polyester buckle and hooks also available in stainless steel Standard lashing also available as packed in plastic bag aswell as a special bucle with two wheels and ABS loosening function package size 10 psc / pack

Product code: SV2000102H SV2000102P (packed in plastic bag)

SEE CORNER PROTECTORS FOR LASHING IN PRODUCT GROUP 12, AND ALTERNATIVE END FITTINGS PAGE 11-7

11 - 3

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

LASHING SYSTEMS

LASHING SYSTEM LC 2000 KG

• • • • •

for normal lashing in trucks length 0,5 + 9,5 m standard end fittings steel double J-hooks webbing width 50 mm webbing material 100 % polyester

LASHING SYSTEM LC 2500 KG

• • • • •

for lashing heavy items in trucks standard end fittings steel double J-hooks webbing width 50 mm webbing material 100 % polyester also downward tightening ERGO model, stainless steel buckle and hoosk as well as the ABS model that can be loosened gradually without the risk of a rolling or falling load are also available.

ERGO

Product code: SV3500102V

Product code: SV2500102V

LASHING SYSTEM LC 3000 KG

• • • • • •

for lashing heavy items length 0,5 + 9,5 m “Extra heavy” gear lock clamp standard end fittings steel double J-hooks duplex 50 mm webbing webbing material 100 % polyester

LASHING SYSTEM LC 4300 KG

• for lashing extremely heavy items on boats and • • • •

carriages etc. Length 0,5 + 5,5 m standard end fittings steel double J-hooks webbing width 75mm webbing material 100% polyester

Product code: SV4300102

Product code: SV700062

LASHING SYSTEM LC 6000 KG

LASHING SYSTEM LC 5800/7000 KG

• for lashing super heavy items on boats and

• for lashing super heavy items on boats and carriages

• • • •

• • • •

carriages etc. length 0,5 +5,5 m forged hooks as standard end fittings webbing width 100 mm webbing material 100% polyester

etc. length 0,5 + 2,0 m forged hooks as standard end fittings webbing width 60 mm webbing material 100% polyester

Ratchet mechanism SIVKI28

Product code: SV900062

Product code: SV150252 (LC 5800 kg) SV200252 (LC 7000 kg)

SEE CORNER PROTECTORS FOR LASHING IN PRODUCT GROUP 12, AND ALTERNATIVE END FITTINGS PAGE 11-7 • Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 4

11

CAR LASHING / TRACK LASHING SYSTEMS

LASHING SYSTEM FOR TRAILERS

• • • • • •

LASHING SYSTEM FOR TRAILERS

for lashing trailers on boats length 0,5 + 2,5 m breaking strength straights 10000 kg standard end fittings forged hook / elephant hook webbing width 50 mm webbing material 100 % polyester

• • • • • •

for lashing trailers on boats length 0,5 + 2,0 m breaking strength straight 20000 kg standard end fittings forged hook / elephant hook webbing width 75 mm webbing material 100 % polyester

Product code: SV200252L

Product code: SV10032

TRACK LASHING SYSTEM, LC 1000 KG

• for lashing from tracks of enclosed body trucks • lengths 1,0 + 3,0 m / 1,0 + 5,0 m • steel double wire hooks with latch standard end fittings

• webbing width 45 mm • webbing material 100% polyester

CAR LASHING LASHING SYSTEM, LC 1500 KG

• • • • • • •

for lashing a car on a car trailer length 0,3 + 1,5 m the hooks can be fitted directly to the trailer holes lashing over wheel in the same sidection rubber stop plate agains the wheel reeved with the stap of the lashing’s long part webbing disth 50 mm webbing material 100% polyester

Product code: SV200252L

Product codes: SVR11004V (1,0 + 3,0 m) SVR11006V (1,0 + 5,0 m) TRACK LASHING SYSTEM ABT-1100T, LC 1100 KG

• for lashing from tracks in trucks • Lenghts 1,0 + 3,0m (T4) and 1,0 + 5,0m (T6) • over-centre buckle "TENDEX" • standard end fittings steel double wire hooks • webbing width 45 mm • webbing material 100% polyester

STRAPULLI PULLING AND LIFTING WINCH, LC 1000 KG

• the webbing goes through ratchet so that it can be used for lashing and as pulling/lifting winch

• two lengths, 5 ja 10 m • WLL in lift 200 kg • steel double wire hooks with latch as standard end fittings

• webbing width 35 mm • webbing material 100% polyester • handy pulling winch for motor sledges, vehicles etc. Product codes: STRAP1500 (5 m) STRAP150010 (10 m)

Product codes: SV1100T4 (4 m) SV1100T6 (6 m) CORNER PROTECTORS FOR LASHING -> SEEN PRODUCT GROUP 12

11 - 5

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

ROLLO / LASHING STRAPS

ROLLO- LASHING SYSTEM Ratchet tie down that is very easilly operated especially due to automatical rewinding mechanism. Thanks to the mechanism webbings do not strangle anymore. Is suitable for lashing in transportet, trailer, boat trailer, van or any equivalent.

LC

Length

kg

Breaking strength kg

Weight

m

Webbing width mm

250 600

500 1200

3,0 0,5 + 2,7

25 50

0,75 1,45

Product code

kg

ROLLO253 ROLLO503

Clamp can be bolted on the floor

LASHING STRAP

• For bundeling and lashing for different purposes • • •

from industry to hobbies webbing width 25 mm webbing material 100% polyester also available in other lengths ja and end fittings eg. 35 ja 50 mm webbing

Pack

Length

Product code

m

seperate

2 psc / bag assortment

0,5 1,0 2,0 3,0 4,0 5,0 0,5 1,0 2,0 3,0 5,0

SVPL25005 SVPL2501 SVPL2502 SVPL2503 SVPL2504 SVPL2505 SVPL25005IPV SVPL2501IPV SVPL2502IPV SVPL2503IPV SVPL2505IPV SVPL250LABT

Assortment 8 kpl / 1,0 m red 8 kpl / 2,0 m orange 8 kpl / 3,0 m blue 8 kpl / 5,0 m black

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 6

11

END FITTINGS

NOTE! Breaking strength (BS)

LASHING FITTINGS

Webbing width (WW)

Double J hooks

Double J hooks with safety latch

BS WW PC 800 kg 25 mm KO25008 1600 kg 25 mm KO25016 3000 kg 35 mm KO3503 5000 kg 50 mm KO5005 8000 kg 60 mm KO6010 10000 kg 75 mm KO7510

BS WW PC 3000 kg 35 mm KOSA353IXI 5000 kg 50 mm KOSA505IXI

close rave-, claw-, flat hooks BS WW PC 2000 kg 50 mm KOPAL20

Single J hooks BS WW PC 2500 kg 35 mm KOK35025 3000 kg 50 mm KOK503 5000 kg 50 mm KOK505

KIKL5002

1600 kg

50 mm

KIKL50

KOKS45

5000 kg

50 mm

KOKS505S

2500 kg

50 mm

KOPAL25

50 mm

2000 kg

Strap hooks

20000 kg

65 mm

KO6520

20000 kg

AKO13L

Special end fittings plane and vertical rail

BS WW PC 1500 kg 25 mm KOL2501 1500 kg 35 mm KOL3503 5000 kg 5000 kg

50 mm 50 mm

KOL5005 KOL5005L

5000 kg

50 mm

KOL5005R

6000 kg

50 mm

KOL5006LH

20000 kg

60/75 mm

KOL7515

Combi track end

BS WW PC 2000 kg 50 mm COM5002 2000 kg 50 mm COM5002

EP18 KIP1800

BS 1800 kg

PC EP18 + KIP1800

2500 kg

EP25 (without link)

2300 kg

EP25E (circular link)

2300 kg

EP26 (oval link)

Elephant hooks BS 20000 kg

PC ELV20

24000 kg

ELH20

20000 kg

ELS20

Winch hooks

Swivel J hooks BS WW PC 3000 kg 35 mm KOSL3503 5000 kg 50 mm KOSL5005

11 - 7

SALKE5000LBS

BS WW PC 12000 kg 65 mm KO6512 15000 kg 65 mm KO6515

KOKS505K

D-, triangle-,delta- rings

- stainless

KOS50031

BS WW PC 5000 kg 50 mm KOSA5005

- with swivel

5000 kg

50 mm

fotgrd hook with ring

BS WW PC 2500 kg 25 mm KOS5002 45 mm

KOPAL50

3000 kg

Snap hooks

5000 kg

50 mm

BS WW PC 3000 kg 35 mm KOS3503 5000 kg 50 mm KOS5005

Track hooks

50 mm

5000 kg

Double J hook with tube

BS WW PC 1600 kg 50 mm KOKI5016 1600 kg

Product code (PC)

BS 2000 kg 3500 kg

PC VINSKOU VINSKOU35

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

WINCHES / WHEEL CHOCKS / ANTI-SLIP MATS

LASHING WINCHES

• standard fitting double J hook • webbing width 50 mm • webbing material 100% polyester Type

K-type

P-type

Ratchet mechanism Product code: SIVKI28

LC

Lashing winch with webbing, K-type Lashing winch with webbing, K-type Lashing winch with webbing, P-type Winch webbing 2500, fits K-type Winch webbing 1600, fits K- and P-types Only lashing winch, K-type Only lashing winch, P-type

Product code

kg

Standard length m

2500 1600 1600 2500 1600 2500 1600

10 10 10 10 10 -

SIV3500K10 SIV2000K10 SIV2000P10 VV350010 VV200010 SIV2035K SIV2000P

TRAILER WHEEL CHOCK

• full rubber wedge that you can equip with spikes • three sizes

Dimensions (l x w x h)

Weight kg

Product code

170 x 100 x 95 243 x 127 x 230 290 x 190 x 150

0,6 3,8 5,3

PYKMINI PYKPIENI PYKISO

ANTI-SLIP MATS • Anti-slip mat for transport protection of shipped goods. Also well suited for use as protective packaging in non-transport applications. • Rubber granulate 1-3 mm made from recycled materials, bound with polyurethane elastomer • tensile strenght apprx 0.6 N/mm2 • coefficient of friction apprx. 0.65 for dry mats

Thicknesss mm 3 5 6

roll

Tensile strenght

m

N/mm2

20 12 10

0,6 0,6 0,6

Product code

KITMA3R KITMA5R KITMA6R

Custom size available on request!

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 8

11

CARGO NETS / LASHING TARPAULINS

CARGO NETS

• for lashing trash, construction waste loads etc. • appr. n. 1.0 m lashing ropes • other sizes also available

Net size m

Net rope mm

Eye size mm

Weight kg

Product code

3,5 x 5 3,5 x 6 3,5 x 7

3,0 3,0 3,0

40 40 40

2,4 2,8 3,3

KUV35540 KUV35640 KUV35740

PVC CARGO TARPAULIN

• made as the cargo cover • holes reinforced with metal approx every 1 metre on the edges

• approx 1,5m lashing ropes are included in the delivery (seperate)

• lashing rubber can also be used in the trapaulin • other sizes also available

11 - 9

Net size m

Eye size approx. mm

Weight kg

Product code

3,5 x 6 3,5 x 7

2 2

7,4 8,6

KUV356PVC KUV357PVC

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

LASHING CHAINS / FORREST CHAINS

LASHING CHAINS FOR LOAD BINDERS / TOWING CHAIN

• • • • •

for lashing extremely heavy items on boats and carriages etc. latch hooks as standard end fittings short link grade 8 chain black or shiny Dacromet- chain also available with grade 10 components

Chain size

LC

mm

kg

6 (L-8) 8 (L-8) 10 (L-8) 13 (L-8) 16 (L-8)

2250 4000 6300 10600 16000

Breaking Standard Weight Product code Product code strenght length with shiny kg with black Dacrometkg m chain chain 4500 8000 12600 21200 32000

5 5 5 5 5

4,6 8,4 12,7 21,9 34,6

SIK0605M SIK0805M SIK1005M SIK1305M SIK1605M

SIK0605K SIK0805K SIK1005K SIK1305K SIK1605K

Ratches on the next page

HEAVY CARGO LASHING CHAINS

• lashing for extremely heavy cargo on boats and timber cars in automatic lashing devices

• by the meter or specific size with various hook etc. end fittings • ling link grade 8 chain Chain size (inner width x inner length)

LC

Breaking strength

Weight

mm

kg

kg

kg

6 (10x35) 9 (16x57) 11 (18x66) 13 (25x81) 16 (27x88)

2250 5000 7500 10500 16000

4500 10000 15000 21000 32000

0,65 1,50 2,10 2,90 4,60

Product code

SIK06P SIK09P SIK11P SIK13P SIK16P

You will find lever load binders and hooks on the next page

CHOKER CHAIN

• • • • •

chain 7 mm length of spike 250 mm length of chain 2.3 m breaking strength 6800 kg grade 8 Product code: JKE23

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 10

11

LOAD BINDERS

LOAD BINDER WITH COLLAPSIBLE TENSION GRIP • extended tension length • excelent use convenience • collapsible tension grip • EN-standard safety latch hooks • two sizes, for 8 and 10 mm lashing chains • breaking strength 8 t ( 8 mm ) and 12,6 t ( 10 mm ) • Equivalent EN-standard LC-rates: 4000 daN ja 6300 daN • In accordance with finnish road regulations

Handling is easy thanks to long main tube.

Product codes: VA8P ( 8 mm) VA10P (10 mm)

LOAD BINDER - RATCHET TYPE

• for short link lashing chains • binders with direction switch and grab

Chain size

hook ends

mm

Breaking strengthkg

LC

4000 8600 15000 21000

6 8 - 10 10 - 13 13 - 16

Weight

kg

Tension length appr. mm

2000 4300 7500 10500

150 150 150 150

1,6 4,8 5,8 6,5

VA6 VA8 VA1013 VA16

145 145 300

5,6 6,6 10,5

VA10EN VA13EN VA16EN

Weight

Product code

3,8 5,5

kg

Product code

EN- standard rachet load binders 10 13 16

LOAD BINDER - LEVER TYPE

12600 20000 32000

6300 10000 16000

• for short link lashing chains • tensioning with and eccentric handle • tensioin length appr. 120 mm Chain size

LC

mm

Breaking strength kg

kg

Tension length appr. mm

8 10 – 13

8600 15000

4300 7500

120 120

kg

PK810 PK1013

LASHING LEVER

• for long link lashing chains • only for lashing cargo on ships (not approved for road transport)

Chain size

Breaking strength

Weight

mm

kg

kg

9 11 13

10000 15000 20000

3,5 3,9 6,0

Product code

KAR9 KAR11 KAR13

MARINE HAMBURGER TURNBUCKLES

• for tightening a steel rope in cargo lashin on ships (tension length appr. n. 240 mm)

11 - 11

Seel rope dimensions mm

Breaking strength

12 –14 16 - 18

13000 20000

Thread koko

Weigth

M24 M27

1,9 3,0

kg

kg

Product code

HAV13 HAV20

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

LASHING CHAIN END FITTINGS

CLEVIS SLING HOOK WITH LATCH

• the hook is attached directly • •

to the chain without a connection link grade 8 not to be heat treated

For chain mm

LC

6 (L-8) 8 (L-8) 10 (L-8) 13 (L-8) 16 (L-8)

2,25 4,0 6,3 10,6 16,0

t

Breaking K H P1 Weigth Product code strength t mm mm mm kg 4,5 8,0 12,6 21,2 32,0

75 83 105 127 150

20 26 37 48 60

18 22 30 40 54

0,35 0,60 1,06 1,80 3,40

SALKH6 SALKH78 SALKH10 SALKH13 SALKH16

CLEVIS CRAB HOOK

• the chain is attached directly to • •

the chain without a connection link mainly for shortening 9 ja 10 mm chains not to be heat treated

For chain

LC

Weight

t

Breaking strength t

mm 9 / 10

6,3

12,6

0,3

Product code

kg AKOH1/2

CLEVIS HOOK FOR LASHING CHAIN

• the hook is attached directly to • •

the chain for long link chains not to be heat treated

For chain mm

Breaking strength t

Weight kg

Product code

10 15 21

0,5 0,9 1,1

AKOHS09 AKOHS11 AKOHS13

For chain mm

Breaking strength t

Weight kg

Product code

9/11/13

20

0,8

ELH20

9 11 13

CLEVIS ELEPHANT HOOK

• the foot is attached directly to • •

the chain for long link chain nt to be heat treated

PELICAN HOOK

• hook opens quicly by hitting / trigger • for chain or steel sope • not to be heat treated

Breaking strength t

Weight kg

Product code

17

1,6

PELISH16

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 12

11

CARGO TRACKS AND DECKING ACCESSORIES

CARGO TRACKS

• a wide range of special

Type

tracks is also available

Round hole track, steel Combi track, steel

Track with holes

Breaking strength kg

Length m

2000 2000

3,05 3,00

Weight Product code kg 5,50 8,00

SIRK1000 SICO3T

Track with holes

Combi track Combi track

END PARTS FOR TRACKS

• steel end part for track with holes • ABS plastic end part for combi tracks

SIRKPAA SICOPAA

type

product code

round hole track compi track

SIRKPAA SICOPAA

DECK BEAM FOR COMBI TRACK

• enables loading for several levels • beam to be used can be wood or metal sized 40 x 150 mm Type Deck beam.

11 - 13

Max. load appr. Weight kg / pair kg 300

0,7

Product code VTKA300

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11

LOAD SUPPORTONG ACCESSORIES / LASHING POINTS

CARGO BAR - LENGHT ADJUSTABLE

• for lashing cargo in enclosed body and pickup trucks horizontally or vercically • works mechanically or with gas springs • Spare parts also available Type

Mechanic Mechanic gas spring

Material

aluminium steel steel

Adjustment range m

Shape

2,35-3,2 2,35-3,1 2,35-3,35

round square square

Max workload appr. kg

Weight

300 300 300

6,0 7,0 7,0

Product code

kg KTTU300P KTTU300 KTTU300PGAS

KTTU300P

KTTU300PGAS

KTTU300

ROUND SHORING BAR

• bars suitable for cargo track holes • spring loaded

Type

TerAs

Adjustment Max workload range appr. m kg 2,22-2,6

400

Weight

Product code

kg 9,0

KTU400PT

LASHING POINT EP-1800

• dry installed base with screw fixing for EP18- (page 11-8) end fittings • very small, but high strength

EP18

Type

Dry install

KIP1800

Breaking strength kg

Mounting method

Weight

1800

screw

0,02

Product code

kg KIP1800

25,4

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS

11 - 14

11

CARGO LASHING POINTS

WELD-ON LASHING POINTS

• for ships carriage, rimber cars etc. • four size

KIPH10-36

KIPH67

LC

Breaking strength

kg

kg

5000 10000 18000 33500

10000 20000 36000 67000

Mounting method

welding welding welding welding

Dimensions

Paino

hxdxp

kg

18 X 95 X 80 25 X 110 X 85 22 X 130 X 80 35 X 155 X 95

0,8 1,2 2,9 5,3

Tuotekoodi

KIPH10 KIPH20 KIPH36 KIPH67

LASHING POINTS KIP-4000 JA -4000R

• pultti- ja/tai ruuvikiinniteinen upotettava kiinnityslenkki Type

LC kg

KIP4000R

Inlaid Inlaid

KIP4000

Breaking Mounting strength method kg

2000 2000

4000 4000

diameter x Weight height mm kg

bolt 82,0 x 19,0 bolt/screw 120,0 x 18,5

0,15 0,15

Product code KIP4000 KIP4000R

WELDABLE LASHING POINTS KIP-4000N / KIP-8000N/P

• weldable lashing points to be inlaid at pallet level • also enable lashing underneath Type

LC kg

KIP8000P

KIP8000N

KIP4000N Inlaid / rectangular 2000 Inlaid / square 4000 Inlaid / round 4000

Breaking Mounting point method kg 4000 8000 8000

width x lashing Weight Product length x poing code height inner (frame) mm width kg mm

welding 80 x 40 x 45 welding 70 x 70 x 110 welding 63,5 Ø x 110

31 30 24

0,3 0,5 0,5

KIP4000N KIP8000N KIP8000P

WELD ON LASHING POINT KIP-7500

• Weldable lashing point to be inlaid at pallet level Type

LC kg

Inlaid / square

3750

Breaking point kg

Mounting method

7500

welding

leveys x pituus x korkeus mm

Weight Product code kg

96 x 90 x 29

0,5

KIP7500

LASHING POINT KIP-6000

• weldable or boltable frame hook • suitable for triangle end (not round steel bar triangle) Type

Dry install

11 - 15

LC

Mounting method

Weight

kg

Breaking strength kg

3000

6000

hitsaus

0,3

Product code

kg KIP6000

• Tel. +358 2 511 5511 • [email protected] • www.haklift.com LIFTING, LASHING AND MATERIAL HANDLING PRODUCTS FOR PROFESSIONALS