VINCI TECHNOLOGIES PETROPHYSICS CATALOGUE OF PRODUCTS 2011

2011 PETROPHYSICS VINCI TECHNOLOGIES CATALOGUE OF PRODUCTS PETROPHYSICS Core preparation Routine core analysis Special core analysis Component...
26 downloads 3 Views 3MB Size
2011

PETROPHYSICS

VINCI TECHNOLOGIES

CATALOGUE OF PRODUCTS

PETROPHYSICS

Core preparation

Routine core analysis

Special core analysis

Components

LIST OF INSTRUMENTS

PETROPHYSICS

CORE PREPARATION ______________________________________ 6  PLUGGING MACHINE __________________________________________________________ 7  RADIAL CORE SLABBING SAW ___________________________________________________ 8  AUTOMATIC SLABBING SAW ____________________________________________________ 9  CORE CUTTING SAW __________________________________________________________ 10  TRIMMING SAW _____________________________________________________________ 11  ENDFACE GRINDER __________________________________________________________ 12  TRIMMING / ENDFACE GRINDER ________________________________________________ 13  CENTRIFUGAL EXTRACTOR ____________________________________________________ 14  CO2 SOLVENT CORE CLEANER (CSC 70)__________________________________________ 15  SOXHLET EXTRACTOR ________________________________________________________ 16  FLOW THROUGH CORE CLEANER ________________________________________________ 17  RECOVERY STILL FOR SOLVENT_________________________________________________ 18  HUMIDITY DRYING OVEN ______________________________________________________ 19  VACUUM DRYING OVEN _______________________________________________________ 20  AIR FORCED DRYING OVEN ____________________________________________________ 21  HEATED VACUUM DESSICATOR _________________________________________________ 22  MANUAL SATURATOR ________________________________________________________ 23  AUTOMATED SATURATOR _____________________________________________________ 24  CORE DESAGREGATOR ________________________________________________________ 25  STEREOMICROSCOPE _________________________________________________________ 26  ULTRA VIOLET BOX __________________________________________________________ 27  CORE PRESERVATION KIT _____________________________________________________ 28 

ROUTINE CORE ANALYSIS _________________________________ 29  HIGH PRECISION DIGITAL BALANCES _____________________________________________ DEAN STARK EXTRACTOR _____________________________________________________ RETORT OVEN ______________________________________________________________ GAMMA RAY LOGGER (NGR 200) _______________________________________________ GEOMETRIC BULK VOLUME METER (GBV) _______________________________________ IMMERSED BULK VOLUME METER (IBV) _________________________________________ MERCURY POROMETER _______________________________________________________ HELIUM POROSIMETER (HEP) __________________________________________________ HELIUM POROSIMETER FOR EDUCATIONAL PURPOSES (HEP-E) ________________________ STEADY STATE GAS PERMEAMETER (GASPERM) ____________________________________ STEADY STATE GAS PERMEAMETER FOR EDUCATIONAL PURPOSES (GPE30) ______________ WHOLE CORE STEADY STATE GAS PERMEAMETER (WHOLEPERM) ______________________ STEADY STATE GAS PERMEAMETER AND POROSIMETER (POROPERM) ___________________

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

3/100

30  31  32  33  34  35  36  37  38  39  40  41  42 

PETROPHYSICS

STEADY STATE GAS PERMEAMETER AND POROSIMETER FOR EDUCATIONAL PURPOSE (POROPERM - E) _____________________________________________________________ 43  CALIBRATED PERMEABILITY CHECK PLUGS _______________________________________ 44  UNSTEADY STATE AND STEADY STATE GAS PERMEAMETER AND POROSIMETER AT MODERATE CONFINING PRESSURE (COREVAL 30) ___________________________________

45 

UNSTEADY STATE AND STEADY STATE GAS PERMEAMETER AND POROSIMETER AT (COREVAL 700) ______________________________________ OVERBURDEN PRESSURE

46 

AUTOMATED SAMPLE LOADING UNSTEADY STATE AND STEADY STATE PERMEAMETER AND POROSIMETER AT OVERBURDEN PRESSURE (KEYPHI) ________________________________ 47  LIQUID PERMEAMETER (LIQPERM) ______________________________________________ 48  BENCH TOP PERMEABILITY SYSTEM (BPS 350) ____________________________________ 49  BENCH TOP UNSTEADY STATE RELATIVE PERMEAMETER (BRP 350) ___________________ 50  BENCH TOP UNSTEADY & STEADY STATE LIQUID – LIQUID RELATIVE PERMEAMETER (SRP 350) ______________________________________________________________________ 51  ELECTRICAL PROPERTIES SYSTEM @ AMBIENT CONDITIONS (EPS-A) __________________ 52  ELECTRICAL PROPERTIES SYSTEM @ OVERBURDEN PRESSURE (EPS 700)________________ 53  EDUCATIONAL CAPILLARY PRESSURE CELL _______________________________________ 54  MULTI SAMPLE CAPILLARY PRESSURE CELL _______________________________________ 55  CAPILLARY PRESSURE REFRIGERATED CENTRIFUGE (RC4500) ________________________ 56  CAPILLARY PRESSURE MERCURY SYSTEM (CPM 140) _______________________________ 57  DIGITAL CORE PHOTOGRAPHY SYSTEM (DCP) _____________________________________ 58 

SPECIAL CORE ANALYSIS _________________________________ 59  CORE FLOOD SYSTEM FOR EOR STUDIES (CFS 700) _________________________________ UNSTEADY STATE RELATIVE PERMEAMETER (AUTOFLOOD 700) _____________________ STEADY STATE AND UNSTEADY STATE RELATIVE PERMEAMETER SYSTEM (RPS 700) _______ XRAY SCANNER FOR IN-SITU SATURATION MONITORING _____________________________ FORMATION DAMAGE AND WELL TREATMENT EVALUATION SYSTEM (FDS 350) __________ CAPILLARY PRESSURE AND RESISTIVITY INDEX SYSTEM (CAPRI) _____________________ ROCK COMPRESSIBILITY SYSTEM (RCS 700) ______________________________________ ATMOSPHERIC ACOUSTIC VELOCITY SYSTEM (AVS A) ______________________________ OVERBURDEN ACOUSTIC VELOCITY SYSTEM (AVS 700) _____________________________ AUTOMATED HP-HT ACOUSTIC VELOCITY SYSTEM (AVS 700-HT) ___________________ AGING CELL APPARATUS (ACA 700) ____________________________________________

60  61  62  63  64  65  66  67  68  69  70 

COREHOLDERS __________________________________________ 71  HASSLER COREHOLDER (HAS SERIES) ____________________________________________ HYDROSTATIC COREHOLDER (HYC SERIES) ________________________________________ TRIAXIAL COREHOLDER (TRC SERIES) ____________________________________________ LEAKOFF COREHOLDER (LEC SERIES) ____________________________________________ QUICK RELEASE COREHOLDER (QRC SERIES)_______________________________________ TRANSPARENT COMPOSITE COREHOLDER (TCC SERIES) ______________________________ ACOUSTIC VELOCITY COREHOLDER (AVC SERIES) __________________________________ ELECTRICAL RESISTIVITY AND CAPILLARY PRESSURE COREHOLDER (ECP SERIES) _________

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

4/100

72  73  74  75  76  77  78  79 

HEATING SYSTEM (HES SERIES) _________________________________________________ 80  STANDS (STA SERIES) _________________________________________________________ 81 

PETROPHYSICS

CORE ANALYSIS COMPONENTS ____________________________ 82  LEVEL TRACKER SEPARATOR (LTS SERIES) ________________________________________ 83  DUAL LEVEL TRACKER (DLT SERIES) ____________________________________________ 84  AMBIENT CONDITIONS TWO PHASE VIDEO SEPARATOR (VSE -A) ________________________ 85  HP-HT TWO PHASE VIDEO SEPARATOR (VSE 700) ____________________________________ 86  WET GAS METER (WG SERIES) __________________________________________________ 87  CAPILLARY SIGHT GLASS TUBE _________________________________________________ 88  BACK PRESSURE REGULATOR (BPR) _____________________________________________ 89  ELECTRICAL ISOLATOR (EI 700) ________________________________________________ 90  AUTOMATED CONFINING PRESSURE CONTROLLER (ACP 700) _______________________ 91  FLOATING PISTON ACCUMULATOR (FPA SERIES) ___________________________________ 92  MIXER CYLINDER (MC SERIES) _________________________________________________ 93  FLUID TRANSFER VESSELS (FTV SERIES) __________________________________________ 94  HYDRAULIC INTENSIFIER (HI SERIES) ____________________________________________ 95  PRESSURE GENERATOR SYSTEM (PGS) ___________________________________________ 96  DIGITAL PRESSURE GAUGE (DPG SERIES)__________________________________________ 97  DEADWEIGHT GAUGE ________________________________________________________ 98  UNINTERRUPTABLE POWER SUPPLY (UPS 16) ______________________________________ 99  OTHER COMPONENTS ________________________________________________________ 100  The specifications and photos contained in this catalogue can be subject to change without notification. Copyright© Vinci Technologies. All rights reserved.

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

5/100

PETROPHYSICS

CORE PREPARATION

Core cutting

Core cleaning

Core drying

Core saturation

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

6/100

PLUGGING MACHINE

PETROPHYSICS

The heavy built diamond tooled drill press is especially designed to drill in various size core samples. The standard machine comes with a floor standing drill press, a rotary union, a coolant feeding system, a coolant recovery pan with splash guard and a core clamping vise. The union permits to connect the coring bit to the drill press and feed coolant to the coring bit. The vise assembly can be mounted on the pan table and allows for the positioning of the core. Various sizes of coring bits as well as the recirculating coolant system are available.

FEATURES Coring bit internal diameter: Maximum coring depth: Drip pan dimension: Compatible coolant: Drill speed: Motor power: Electrical: Weight: Volume:

1", 1.5", 2" 5 inches (12.5 cm) L x W x H: 600 x 300 x 250 mm Water, Oil 360, 520, 800, 1150, 1840, 2650, 4070, 5750 RPM 1100 watts, 1500 RPM 220 VAC 1 phase, 60 Hz 150 kg 500 x 500 x 1800 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

7/100

RADIAL CORE SLABBING SAW

PETROPHYSICS

Versatile diamond impregnated radial blade utilised to slab core samples in two halves or to trim full diameter rock samples. The standard machine comes with a worktable, blade guard, motor to power the saw, core clamp assembly for holding core, sample trolley on ball bearing guide, coolant feeding system , coolant recovery pan and diamond impregnated saw blade. The recirculating coolant system is also available.

FEATURES Saw blade diameter Maximum cutting depth Max core length Compatible coolants Power supply Weight

400 mm (16’’) (other upon request, max 500 mm) 125 mm (5”) 300 mm, 1000 mm in option Water and oil 220 VAC, 50 Hz, 4,000 W 320 kg

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

8/100

AUTOMATIC SLABBING SAW

PETROPHYSICS

Versatile diamond impregnated radial blade utilized to slab core samples in two halves or to trim full diameter rock samples. The automated machine is fitted with a variable rate feed mechanism that enables the cutting of long section of very dense core in one pass without fracturing, grooving or chipping and producing a high-finished surface. The core sample remains fixed, while the carriage holding the diamond disc and motor unit moves along the core sample at an adjustable and regulated speed. The moving of the saw blade along the core sample starts when the cutting depth is reached. The saw arm oscillates around an axis so that a constant cut pressure is maintained whatever the hardness of the sample material encountered. This pressure is easily adjusted while the machine is in operation.

FEATURES Saw blade diameter Maximum cutting depth Maximum core length Compatible coolants Power supply Weight Volume

500 mm (20’’) 125 mm (5”) 1 meter Water and oil 380 VAC 3 Phases, 50 or 60 Hz, 8,000 W 1200 kg 4000x1050x2030 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

9/100

CORE CUTTING SAW

PETROPHYSICS

Versatile bench top diamond impregnated radial blade utilized to cut plug sized core samples in two halves or to trim rock samples. The standard machine comes with a blade guard, a motor to power the saw, a sample trolley on ball bearing guide, a shut off button, a coolant feeding system, a coolant recovery pan and a diamond impregnated saw blade.

FEATURES Saw blade diameter Maximum cutting depth Max core length Compatible coolants Power supply Weight Volume

350 mm (14”) 100 mm (4”) 300 mm Water and oil 220 or 380 VAC, 50 Hz, 3 horses 82 kg 1120x620x710 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

10/100

TRIMMING SAW

PETROPHYSICS

Bench top tool designed to cut preset core sample lengths. The preset sample lengths can be adjusted at any time by rearranging machined spacers to the desired length between the blades. The quality of the saw blade allows for extreme precision of the end face after trimming of 0.002 inch (5/100 mm). All wetted components are constructed from stainless steel and anodized aluminium for long lasting corrosion free operation. All bearings are sealed to insure long lasting free movement. The containment pans and splash guards are also constructed of heavy gauge stainless steel, anodized aluminium and corrosion free plastic. Recirculating coolant system is also available.

FEATURES Saw blade diameter Saw blade thickness Core diameter Core length Lubricants Power supply Motor power Weight Dimension

200 mm (8’’) 2 mm up to 2’’ 2”, 3” other upon request water (usually), oil 220 VAC 1 phase 50 or 60 Hz 550 W, 3,000 RPM 80 kg 700x800x600 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

11/100

ENDFACE GRINDER

PETROPHYSICS

Tool designed to provide flat, parallel end-faces when sample geometry is critical for advanced rock property test. The tool comes with a core clamping device, housing and cover parts, a coolant feeding system, a coolant recovery pan and a diamond tool end-face grinding wheel. A core clamping device for whole diameter core sample, a recirculating coolant system and hoover for dry grinding operations are also available.

FEATURES Core diameter Grinding wheel precision Wheel diameter Power supply Motor power Weight Volume

up to 2" +/- 0.001 inch (2.5 / 100 mm) 150 mm 220 VAC 1 ph50 or 60 Hz 0,55 kW, 3,000 RPM 70 kg 600x500x500 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

12/100

TRIMMING / ENDFACE GRINDER

PETROPHYSICS

Bench top tool which combines a trimming saw at one side and an endface grinder on the other side. It is designed to cut preset core sample lengths and grind the sample with extreme precision of the end face after trimming of 0.002 inch (5/100 mm).

FEATURES Saw blades diameter Saw blades thickness Grinding precision Grinding wheel diameter Core diameter Core length Lubricants Power supply Motor power Weight Volume

200 mm (8’’) 2 mm +/- 0.001 inch (2.5 / 100 mm) 150 mm up to 2’’ 2”, 3” other upon request Water (usually), Oil 220 VAC 1 ph 50 / 60 Hz 550 W, 3,000 RPM 100 kg 700x800x600 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

13/100

CENTRIFUGAL EXTRACTOR

PETROPHYSICS

The centrifugal extractor is designed to spray warm, clean solvent from a still against the core samples. The centrifugal force causes solvent to flow through samples displacing and extracting the oil (and water). The speed of rotation can be selected depending on the permeability and degree of consolidation of the core. Most common solvents can be used. A solvent recovery still is also provided to recycle clean and warm solvent into the centrifugal extractor in closed loop.

FEATURES Core diameter Core length Quantity of sample Wetted materials Centrifuge speed Electrical

up to 2" up to 3’’ between 6 to 18 depending on the core length Stainless steel, teflon up to 3000 rpm 220V, 50Hz, 1500W

BENEFITS Centrifugal Extractor : Rapid and efficient extraction of oil, water and salt from consolidated core samples Speed controller Rotor geometry to accomodate the core samples Solvent inlet and outlet Vibration free chassis

Solvent recovery still : Heated solvent flask Water refrigerant for solvent condensation Temperature controller

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

14/100

CO2 SOLVENT CORE CLEANER (CSC 70)

PETROPHYSICS

The core Cleaner is a device for cleaning crude oil, drilling mud liquids, and water from a single piece of whole core or from a batch of core plug samples. The principle consists of filling the gas filled space in the core with solvent (e.g. toluene) by surrounding the core with a suitable solvent containing dissolved CO2 gas and applying sufficient hydraulic pressure. The solvent mixes with oil in the core and subsequent depressurizing to atmospheric pressure removes residual oil from the core. A number of repeated cycles are required to clean the core of hydrocarbons. The apparatus fits into a standard size floor hood. The cleaning chamber is a pressure vessel heated electrically with a two-kilowatt, 220-volt heater enclosed in an explosion proof housing. The solvent is pumped from an onboard supply tank to the cleaning vessel with a high pressure pump. A cyclone separator with a stainless steel-packed, water-cooled after-cooler is provided to separate the CO2 and the used hot solvent when the vessel is drained. The used toluene drains into an explosion proof electric still where it is recovered and delivered back to the clean solvent supply. The still operation is automatic. The process controls are housed in a nonexplosion proof box intended to be mounted outside of the hood.

FEATURES Vessel diameter: Vessel length CO2 pressure Solvent pressure Wetted materials Net weight Requirements: Air Electrical Cooling water

Model 1:4.6” (118 mm) - Model 2: 5.2” (134 mm) Model 1:10.7” (274 mm) - Model 2: 27” (660 mm)

200 psi 1,000 psi 316 Stainless steel 200 kg

100 psi 220V, 50Hz, 2,000 Watts 8 l/m @ 14 kPa (2 gpm @ 20 psi)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

15/100

SOXHLET EXTRACTOR

PETROPHYSICS

The soxhlet distillation extraction method is used to dissolve and extract oil and brine from rock core sample by using solvents. The cleanliness of the sample is determined from the color of the solvent that siphons periodically from the extractor which must be clear. The samples are placed in the extractor and cleaned by refluxing solvent. The solvent is heated and vaporized in boiling flasks and cooled at the top by condenser. The cooled solvent liquid falls into the sample chamber. The cleaned solvent fills the chamber and soaks the core sample. When the chamber is full, the dirty solvent which was used to clean the core siphons back into the boiling flask and is redistilled again The apparatus consists of a distillation/extraction glassware unit and a heating mantle with thermostatic controller. The glassware is composed of boiling flask, soxhlet extractor and condenser. A flexible plastic tubing is also used to connect the condenser to the water cooling unit. All these devices are mounted on a mounting rack.

FEATURES SOXHLET FOR PLUG SIZED CORE SAMPLES Configuration Core sample diameter Core sample length Extractor capacity Boiling flask Heating temperature Water cooling system

Single unit model/ Multiple units model (up to 6 extractors) up to 1,5” up to 4” 250 ml 500 ml up to 450°C 0.5 to 3 liters per minute, 18°C

Power supply

220 VAC 50 Hz

SOXHLET FOR FULL SIZED CORE SAMPLES Configuration Core sample diameter Core sample length Extractor capacity Boiling flask Heating temperature Water cooling system Power supply

Single unit model / Multiple units model (up to 6 extractors) up to 4” up to 6” 3 liters 6 liters up to 450°C 0.5 to 3 liters per minute, 18°C 220 VAC 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

16/100

FLOW THROUGH CORE CLEANER

PETROPHYSICS

The apparatus is a rapid and efficient core cleaning system based on controlled sequential solvent displacement under moderate pressure. Extraction of hydrocarbons and salts from reservoir rocks is achieved by injecting one or more solvents into the core sample under pressure and moderate temperature. The pressure used depends on the sample permeability. The core is considered clean when the effluent is clean.

FEATURES Maximum confining pressure Core diameter Core length Fluid flow rate Wetted parts Electrical Weight

1,000 psi 1.5” (other upon request) Up to 3” (other upon request) 5 cc/min (recommended) Stainless steel 220 VAC, 50 Hz 40 Kg

BENEFITS Possibility to pump different solvents Constant injection flow for solvent Easy core loading and unloading operation Cleaning at pressure for high permeability sample

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

17/100

RECOVERY STILL FOR SOLVENT

PETROPHYSICS

The recovery still is designed to reclaim clean solvent from dirty solvent containing a mixture of crude oil and solvent. The recovery process is based on fractional distillation by boiling point temperature difference between the crude oil and the solvent. The apparatus is explosion proof and should be installed away from any area of hazardous atmosphere. It consists mainly of (a) an insulated boiler tank equipped with heaters located at the bottom and (b) a condenser using house water. The recovered solvent is evacuated into a container whereas the dirty toluene is transferred manually into the tank. The plastic bag located in the tank in which the dirty solvent is poured permits to facilitate the evacuation of sludge deposit after the recovery process.

FEATURES Recovery Recovery time Max temperature Tank capacity Protection Material House water consumption Power supply Dimensions Weight

95 % 3 to 5 hours for 20 litres 200°C 20 litres, other upon request IP 66 stainless steel 50 litres per hour 220 VAC 50 Hz , 2,500 W 850x1000x1000 mm 165 Kg

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

18/100

HUMIDITY DRYING OVEN

PETROPHYSICS

The humidity drying oven is used to dry core samples under constant relative humidity condition; in particular it is very important when the core contains hydratable clays or gypsum. This oven is composed of a robust air bath, an electronic temperature regulator, a water vapor injection system, a capacitance probe to control humidity level and a timer.

FEATURES Capacity Humidity range Temperature Humidity stability Temperature stability Internal dimensions Power supply Weight Water consumption

240 liters 10% to 90% +10°C + 90°C +/- 1% +/- 0.1 °C 800 x 500 x 600 mm 220V / 50Hz , 2500 W 184 kg 1 – 10 bar (200 – 500 S/cm)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

19/100

VACUUM DRYING OVEN

PETROPHYSICS

The vacuum drying oven enables fast drying of core under vacuum. This oven is composed of a robust vacuum air bath, an electronic temperature regulator and digital vacuum control through solenoid valves. Two sizes can be selected.

FEATURES MODEL 1: 53 LITRES VACUUM OVEN Capacity Temperature Vacuum Internal dimensions Power supply Weight

53 liters 20 to 200°C 10 mb 400 x 400 x 330 mm (WxHxD) 220V, 50Hz, 1200 W 80 kg

MODEL 2: 115 LITRES VACUUM OVEN Capacity Temperature Vacuum Internal dimensions Power supply Weight

115 liters 20 to 200°C 10 mb 506 x 506 x 450 mm (WxHxD) 220V, 50Hz , 1900 W 150 kg

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

20/100

AIR FORCED DRYING OVEN

PETROPHYSICS

The air forced drying oven enables efficient drying of core samples after cleaning with solvents before permeability or porosity measurements. This oven is composed of a robust air forced convection air bath, a variable speed turbine, an electronic temperature regulator and a timer . Two sizes are available.

FEATURES 53 LITERS MODEL Capacity ……………………. 53 liters Temperature ………………… 220°C Internal dimensions…………..400 x 330 x 400 mm Power supply ……………….220V , 50Hz , 2,000 W Weight ……………………….42 kg

108 LITERS MODEL Capacity ……………………. 108 liters Temperature ………………... 220°C Internal dimensions…………. 556 x 400 x 480mm Power supply………………… 220V , 50Hz , 2,000 W Weight ………………………63 kg

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

21/100

HEATED VACUUM DESSICATOR

PETROPHYSICS

The vacuum heated dessicator is designed especially to dry a bunch of core samples under vacuum. This operation is required to remove humidity of core samples before gas permeability or porosity measurements. The system includes an heated dessicator and a vacuum pump. The dessicator includes a machined stainless steel heating plate with a glass bell, designed to withstand the pressure difference between in and outside. The sealing is secured by a viton Oring between the heating plate and the bell. The samples are dried by direct contact with the heating plate. The small volume and the compact design guarantee a short heating time. It is easy and safe to operate, requires hardly any maintenance, and visibility is perfect.

FEATURES Temperature………………… up to 80°C Vacuum... …...……………… 10 -3 mbar Max pumping speed………… 2.5 m3/h Quantity of sample…………… around 30 Material ………………………..stainless steel 316L Electrical …………………….. 220V, 50Hz,

BENEFITS Rapid and efficient drying Total visibility on the product to be dried Compact

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

22/100

MANUAL SATURATOR

PETROPHYSICS

The manual saturator permits to perform a sequence of vacuum and saturation cycles on plug size samples. The standard apparatus includes a plug sized core cell, a vacuum pump, an hand operated pressure pump (2,000 psi output), a saturant vacuum tank and necessary hand operated valves and plumbing. A larger capacity cell to accommodate full size core samples is also available.

FEATURES Max saturating pressure

2,000 psi

Cell diameter Cell height Wetted materials

58 mm 300 mm 316 Stainless steel (other on request)

Saturant

water, brine, oil or other liquids

BENEFITS Rapid and efficient saturation Can accomodate plug size sample and full sized core sample in option Manual operations Loading carrier for easy loading Dead volume sets to minimize volume of saturant

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

23/100

AUTOMATED SATURATOR

PETROPHYSICS

The automated saturator permits to perform a sequence of vacuum, filling and saturation cycles on plug size samples in an automated mode to free the operator for other tasks. The bench top apparatus comes with a plug sized core cell, a vacuum pump, a high pressure liquid pump (2,000 psi output), a saturant vacuum tank and necessary automated valves and plumbing. A larger capacity cell to accommodate full size core samples is also available. The apparatus is controlled by a computer which allows the operator to open or close the valves, start and stop the high pressure pump, the vacuum pump and to run automatic saturation cycles.

FEATURES Max saturating pressure

2,000 psi

Cell diameter Cell height Wetted materials

58 mm 300 mm 316 Stainless steel (other on request)

Saturant Power supply

water, brine, oil or other liquids 220 VAC, 50 Hz

BENEFITS

Rapid and efficient saturation Can accomodate plug sized sample and full sized core sample Fully automated operations Loading carrier for easy loading Dead volume sets to minimize volume of saturant

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

24/100

CORE DESAGREGATOR

PETROPHYSICS

Designed to pulverize core samples into a small granular texture to be loaded in the sample chamber. The sample is crushed under high pressure between two crushing plates in an enclosed chamber.

FEATURES Crushing type Feed size Initial core size Final particle size Capacity Power supply Dimensions Net weight

by pressure 65 x 65 mm 60 mm 1 to 15 mm up to 200 kg/h 220 or 380 VAC , 50 Hz , 1,100 W 410 x 830 x 720 mm 177 Kg

BENEFITS Adaptable crushing geometry 10 stage gap setting adjustment Crushing plates easily accessed and replaced Not accessible, moving part fully interlocked casing Very fast, uniform comminution Almost loss free grinding Closed grinding chamber with extraction part for dust free operations Easy cleaning, minimum contamination between samples

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

25/100

STEREOMICROSCOPE

PETROPHYSICS

The Stereomicroscope Stemi 2000 meets your demands in two respects. On the one hand it offers the low-price advantage common with Greenough-type instruments, on the other hand it features a performance that will surely surprise you. The extremely wide 7.7:1 zoom range (pancratic system 0.65x...5.0x) zooms them in as hardly any other stereomicroscope of this class can do. It includes a cold light source.

FEATURES Model Magnification Viewing field Working distance Power supply

ZEISS STEMI 2000 x6.5 …x50 Max 23mm 90 mm 220 VAC 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

26/100

ULTRA VIOLET BOX

PETROPHYSICS

The ultra violet box is composed of a ultra violet light tube and a fluorescent white light to enable observation of core and cutting samples under both UV light and white light. An access permits to introduce the sample inside the box without introducing exterior light.

FEATURES: Light Power supply

UV and white fluorescent light 220 VAC 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

27/100

CORE PRESERVATION KIT

PETROPHYSICS

The core preservation kit provides the components necessary for the core preservation technique. It consists of wrapping the core sample in several layers of high quality plastic film to prevent puncturing and then wrapped it again with several layers of aluminum foil, with the free ends crimped together. A wire is tied around the core to make a handle. The foil-wrapped core sample is then dipped in a molten wax coating material for mechanical stabilization. The prepared core is then introduced in a heat sealed plastic bag for transportation.

FEATURES: Roll of high quality plastic film Roll of aluminium film Roll of wire Melting pot for wax coating Wax coating Cooling rack Heat sealer Bag film kit Bags Glue Shovel Pair of gloves Labelling facilities Grabs and scissors

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

28/100

PETROPHYSICS

ROUTINE CORE ANALYSIS

Capillary pressure

Coreval 30

Electrical Properties System

BRP 350

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

29/100

HIGH PRECISION DIGITAL BALANCES

PETROPHYSICS

Digital balances especially selected for core applications where measurement accuracy is required.

FEATURES TYPICAL BALANCE FOR PLUG SIZED CORE SAMPLES Weighing range Accuracy Power supply

0-620 g, other upon request 0.001 g 220 VAC 50 Hz

TYPICAL BALANCE FOR FULL SIZED CORE SAMPLES Weighing range Accuracy Power supply

6,200 g, other upon request 0.01 g 220 VAC 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

30/100

DEAN STARK EXTRACTOR

PETROPHYSICS

The dean stark extractor is used to determine fluid saturation of core samples. The sample is first weighed and then introduced into the dean stark extractor. The water fraction is vaporized by boiling solvent, condensed and then collected in a calibrated receiver. Vaporized solvent also condenses, soaks the sample, and extracts the oil. The sample is then oven dried and weighed. The oil content is determined by gravimetric difference while the water content is volumetrically measured by the receiving tube. The apparatus consists of a distillation/extraction glassware unit and a heating mantle with thermostatic controller. The glassware is composed of boiling flask with extractor, a sample support screen, volumetrically graduated water receiving tube, condenser and desiccant drying tube. A flexible plastic tubing is also used to connect the condenser to the water cooling unit. All these devices are mounted on a mounting rack

FEATURES DEAN STARK FOR PLUG CORE SAMPLE Configuration Core sample diameter Core sample length Extractor capacity Boiling flask Receiving tube Heating temperature Water cooling system Power supply

Single unit model / Multiple units model (up to 6 extractors) up to 1.5” up to 4” 250 ml 500 ml 5 & 10 ml, 0.1 ml graduation up to 450°C 0.5 to 3 liters per minute, 18°C 220 VAC 50 HZ

DEAN STARK FOR FULL SIZE CORE SAMPLE Configuration Core sample diameter Core sample length Extractor capacity Boiling flask Receiving tube Heating temperature Water cooling system Power supply

Single unit model / Multiple units model (up to 6 extractors) up to 4” up to 6” 3 liters 6 liters 40 ml, 0.2 ml graduation with drain valve up to 450°C 0.5 to 3 liters per minute, 18°C 220 VAC 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

31/100

RETORT OVEN

PETROPHYSICS

The retort oven is designed to determine oil and water fluid saturation by a high temperature retorting process in which the oil and water contained in a fresh sample of crushed core material are vaporized, condensed and collected in calibrated glassware. The samples are progressively heated to remove water and then heat up to 650°C (1,200°F) to remove oil from the sample. The gas saturation is determined on an adjacent, litho logically similar sample by placing the core sample in a mercury porosimeter and measuring the amount of mercury injected with the water and/or oil in place. The system comprises a retort cabinet containing two chambers of five sample bombs capable of holding crushed core material. Each bomb is equipped with a sealed threaded cap and is connected to a long, stainless steel condensing tube. The tube passes through a water bath thereby enhancing condensation of the evolved gases. Calibrated glass receiving tube is affixed to each condensing tube with a rubber stopper to collect the water and oil produced from the sample.

FEATURES Sample bomb capacity Receiving tube capacity Number of sample bomb / receiving tub Max Temperature Material Weight Dimensions Electrical

100 grams of crushed core material 20 ml (other size upon request) 10 650°C (1,200 °F) carbon refractory steel 50 kg 1150 x 915 x 535 mm (45 x 36 x 21 in) 220V, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

32/100

GAMMA RAY LOGGER (NGR 200)

PETROPHYSICS

The NGR200 core gamma ray logger provides both total and spectral analysis of the natural gamma radiations emitted from the core samples upon arrival at the laboratory. It permits to differentiate uranium, thorium and potassium concentrations. The data obtained with this apparatus can be used to adjust the depth of the core to coincide with the open-hole logging depths and to identify zones where core has been lost. The apparatus consists of a conveyer for moving core, lead shielding to reduce background gamma radiation and a suitable gamma ray detector. The detector system consists of a shielded scintillation crystal coupled with a photo multiplier. Signals from the detector are processed using a multi channel spectrum analyzer and analytical software. The gamma ray events are energy - sorted and counted over three energy windows K, U and Th as well as the total gamma radiation. Core samples can be in barrel, in a fibre glass, or aluminium, liner or exposed. The core is scanned along its length from bottom to top simulating a wire-line log pass. The logging speed is adjustable to suit the core and data requirements.

FEATURES Belt length Suitable for core Shielding area Sodium Iodine detector Variable logging speed Power supply

3 meters up to 5.5’’ 5 & 3.7 cm around the crystal 3” by 3” up to 5 feet / min 230 VAC 50/60 Hz 1 phase

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

33/100

GEOMETRIC BULK VOLUME METER (GBV)

PETROPHYSICS

This instrument is designed to measure bulk volume of plug sized and/or full diameter core samples with excellent accuracy. The principle consists of measuring accurately the length and diameter of the samples at different grades. Minimum of 8 measurements along the diameter and one every 50 mm along the length are necessary to get an accurate bulk volume measurement. The bulk volume is determined by integrating those measurements. This calculation can be done by hand or by optional computer program. In the latest, calipered dimensional data on core samples are automatically logged and the geometric bulk volume, shape factor, effective flow area and caliper bulk factor are automatically calculated by the program.

FEATURES A digital 150 mm caliper for plug cores with accuracy of +/- 0.02 mm A digital 300 mm caliper for full diameter cores with accuracy of +/- 0.02 mm A software to calculate the bulk volume parameters. Electrical: 220V, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

34/100

IMMERSED BULK VOLUME METER (IBV)

PETROPHYSICS

The immersed bulk volume determination system is designed to measure bulk volume of plug sized core samples with excellent accuracy. The principle consists of immersing the core sample under mercury and measuring with a high precision weighing balance the resulting buoyant force. The bulk volume is then determined by using the Archimede principle.

FEATURES A robust base which supports the balance and a vertical post An adjustable immersion depth and precision ram with level mark A cradle which supports the sample when it is immerged in the mercury A high precision balance with RS232 communication port Reading accuracy: 0.01 g Max weighing: 6,200 g Repeatability: +/- 0.01 g Linearity: +/- 0.01 g A thermometer for mercury density determination Mercury immersion bath Electrical: 220V, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

35/100

MERCURY POROMETER

PETROPHYSICS

Tool designed to measure the gas space and bulk volume of a freshly recovered core sample. The instrument consists of a hand operated pump, a sample cell equipped with a needle valve mounted on its lid. The cell can accommodate a sample with a bulk volume of 10 to 15 cm3. The mercury pump is equipped with a vernier calliper graduated in 0.01 cm3 increments. A pressure gauge capable of indicating pressure up to 100 bar and a vacuum gauge are connected to the system.

FEATURES Max pressure Sample volume Cell size Pump volume Direct reading by vernier Wetted part

100 bar (1,500 psi) 10 to 15 cc 40 x 70 mm 100 cc 0.01 cm3 Stainless steel

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

36/100

HELIUM POROSIMETER (HEP)

PETROPHYSICS

The Helium gas expansion porosimeter is based on the Boyle’s and Charles’ law expansion of helium gas and is used for direct grain volume and pore volume measurement in auxiliary cell at isothermal conditions. Subsequently, porosity and grain density can be derived from the direct measurements. A data acquisition computer allows for data logging and calculation of parameters and also calibration data. The instrument measures grain volume of plug samples of 1” and 1.5” diameter. An optional full diameter matrix cup can be added for determination of grain volume of whole diameter core samples. Each sample matrix cup is interchangeable and is provided with stainless steel calibration check plugs. An auxiliary core holder for plug and whole diameter core samples can also be used to measure pore volume at ambient or overburden pressure.

FEATURES Core diameter: Core length: Porosity Range: Charge Pressure in reference volume: Pressure sensor accuracy: Porosity Range: Electrical requirements: N2/Helium requirements: Dry air requirements:

1” and 1.5”, (4” optional) up to 3”, (up to 12” optional) up to 60% 200 psi 0.1% up to 60% 220 VAC, 50 Hz 500 psi 100 psi

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

37/100

HELIUM POROSIMETER FOR EDUCATIONAL PURPOSES (HEP-E)

PETROPHYSICS

The Helium gas expansion porosimeter is based on the Boyle’s and Charles’ law expansion of helium gas and is used for direct grain volume and pore volume measurement in auxiliary cell at isothermal conditions. Subsequently, porosity and grain density can be derived from the direct measurements. An excel spreadsheet calculation template allows for calculation of grain volume and porosity.

FEATURES Core diameter Core length Porosity Range Charge Pressure in reference volume Pressure sensor accuracy Porosity Range Electrical requirements N2/Helium requirements

1” and 1.5” up to 3" up to 60% 200 psi 0.1% up to 60% 220 VAC, 50 Hz 500 psi

BENEFITS Cost effective Ideal for educational purposes Compact system

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

38/100

STEADY STATE GAS PERMEAMETER (GASPERM)

PETROPHYSICS

The Gasperm instrument is dedicated to measure permeability to gas (air, nitrogen ...) of plug sized core samples at room conditions and reservoir overburden pressure using the steady state method. The instrument is designed for the injection of gas through the test sample at various conditions of pressure and flow rates. The injection pressure at the core face is measured using a pressure transducer and the gas flow rate is measured using a precision mass flow meter. The permeameter console can be configured with a precision pressure control valve to vary the differential pressure and gas flow in the core which allows for the determination of slip factor and Klinkenberg permeability versus reciprocal mean pressure relationship.

FEATURES Permeability Range Flow Pressure Gas flow Temperature Temperature accuracy Pressure transducer accuracy Flow accuracy Nitrogen supply Power

0.01md to 10 darcies 0 to 100 psi 0-50, 0-600 cc/min ambient +/- 0.1 °C 0.1% F.S. 1 % F.S. 250 psi 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

39/100

STEADY STATE GAS PERMEAMETER FOR EDUCATIONAL PURPOSES (GPE30)

PETROPHYSICS

The educational gasperm instrument is dedicated to measure permeability to gas (air, nitrogen,..) of plug sized core samples at room conditions and reservoir overburden pressure using the steady state method. The instrument is designed for the injection of gas through the test sample at various conditions of pressure and flow rates. The injection pressure at the core face is measured using a pressure transducer and the gas flow rate is measured using a precision mass flow metes. An excel spreadsheet calculation template allows for calculation of gas permeability.

FEATURES Permeability Range Flow Pressure Gas flow Temperature Temperature accuracy Pressure transducer accuracy Flow accuracy Nitrogen supply Power

1md to 1 darcy 0 to 30 psi 0-500 cc/min ambient +/- 0.1 °C 0.1% F.S. 1 % F.S. 250 psi 220 VAC, 50 Hz

BENEFITS Cost effective Ideal for educational purposes Compact system

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

40/100

WHOLE CORE STEADY STATE GAS PERMEAMETER (WHOLEPERM)

PETROPHYSICS

The wholeperm instrument is dedicated to measure horizontal and vertical permeability to gas (air, helium, nitrogen,..) of full size core samples at room conditions. The instrument is provided with a gas permeameter console, a full size coreholder and a data acquisition computer station. The air permeability determination is based on the steady state method. The instrument is designed for the injection of gas through the test sample at various conditions of pressure and flow rates. The injection pressure at the core face is measured using a pressure transducer and the gas flow rate is measured using a precision mass flow meter. The permeameter console features a precision pressure metering valve to vary the pressure differential and gas flow in the core which allows for the determination of slip factor and Klinkenberg permeability versus reciprocal mean pressure relationship.

FEATURES Permeability Range Flow Pressure Confining Pressure Gas flow Temperature Temperature accuracy Pressure transducer accuracy Flow accuracy Core diameter Core length

0. 01md to 10 darcies 0 - 100 psi 0 - 400 psi 0-50 and 0-600 cc/min ambient +/- 0.1 °C 0.1% F.S. 1 % F.S. 4” (other upon request) 3 to 6” (other upon request)

BENEFITS Fast loading and unloading operation Wide range of core diameter

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

41/100

STEADY STATE GAS PERMEAMETER AND POROSIMETER (POROPERM)

PETROPHYSICS

The Poroperm instrument is dedicated to measure steady state gas permeability, Klinkenberg permeability, pore volume and grain volume of plug sized core samples at room conditions. The instrument is provided with a permeameter console, an hassler coreholder, a matrix cup and a data acquisition computer station to be operated in manual and automatic mode. An optional hydrostatic coreholder can be used to perform measurement at overburden pressure.

FEATURES Permeability Range: Flow Pressure: Confining Pressure:

0.01md to 10 darcies 0 - 200 psi 0 - 400 psi (option 10,000 psi) Gas flow: 0-50 and 0-600 cc/min Temperature: Ambient Pressure transducer accuracy: 0.1% F.S. Diff. Pressure transducer accuracy: 0.25% F.S. Flow accuracy: 1 % F.S. Core diameter: 1” and 1.5” (option) Core length: Up to 3”

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

42/100

STEADY STATE GAS PERMEAMETER AND POROSIMETER FOR EDUCATIONAL PURPOSE (POROPERM - E)

PETROPHYSICS

The educational poroperm instrument is dedicated to measure steady state gas permeability and porosity of plug sized core samples at room conditions. The instrument is provided with a permeameter console, an hassler coreholder, a matrix cup and a data acquisition computer station to be operated in manual and automatic mode.

FEATURES Permeability Range: Flow Pressure: Confining Pressure: Gas flow: Temperature: Pressure transducer accuracy: Flow accuracy: Core diameter: Core length:

0.5 md to 5 darcies 0 - 100 psi 0 - 400 psi 0-500 cc/min Ambient 0.1% F.S. 1 % F.S. 1” and 1.5” (option) Up to 3”

BENEFITS Cost effective Ideal for educational purposes Compact system

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

43/100

CALIBRATED PERMEABILITY CHECK PLUGS

PETROPHYSICS

The check plugs are used to check and test the calibration of gas permeameters. The set consists of five stainless steel check plugs with different permeability to air. The plug is made of a shell that protects the porous media. These calibration plugs are not primary standards and have been tested using customary testing methods.

FEATURES Diameter Length Permeability range Porosity range

1.0 inch, 1.5 inch, 30 mm, 50 mm (other upon request) 1.0 inch 0.05 -0.15 md, 0.7-2md, 8-15 md,40-70md, 150-220 md 2 to 35 %

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

44/100

UNSTEADY STATE AND STEADY STATE GAS PERMEAMETER AND POROSIMETER AT MODERATE CONFINING PRESSURE (COREVAL 30)

PETROPHYSICS

The Coreval 30 instrument is dedicated to measure the porosity and permeability to helium/nitrogen of plug sized core samples at a fixed confining pressure of 400 psi maximum. The instrument is provided with a data acquisition and calculation computer station. Permeability measurements are made using the steady state method and unsteady state pressure drop method. This data is used to determine the equivalent liquid permeability, slip and turbulence factors. Equivalent air permeability at a user specified pressure is also computed. Porosity and pore volume measurements are made using the Boyle’s and Charles’ law technique.

FEATURES Permeability Range Porosity Range Pore Pressure Confining pressure Temperature Temperature accuracy Pressure transducer accuracy Flow meter Helium N2 Air Power

0.01md to 10 darcies (SS) and 0.001md to 10 darcies (USS) up to 60% 250 psi up to 400 psi ambient +/- 0.1 °C 0.1% F.S. 0-600 cc/min 400 psi 500 psi 100 psi (dry) 110 / 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

45/100

UNSTEADY STATE AND STEADY STATE GAS PERMEAMETER AND POROSIMETER AT OVERBURDEN PRESSURE (COREVAL 700)

PETROPHYSICS

The Coreval 700 instrument is dedicated to measure the porosity and permeability to helium/nitrogen of plug sized core samples at multiple confining pressures ranging from 400 psi to 10,000 psi. The instrument is provided with a data acquisition and calculation computer station. Permeability measurements are made using the steady state method and unsteady state pressure drop method. This data is used to determine the equivalent liquid permeability, slip and turbulence factors. Equivalent air permeability at a user specified pressure is also computed. Porosity and pore volume measurements are made using the Boyle’s and Charles’ law technique.

FEATURES Permeability Range Porosity Range Pore Pressure Confining Pressure Temperature Temperature accuracy Pressure transducer accuracy Flow meter Helium N2 Air Power

0.01md to 10 darcies (SS) and 0.001md to 10 darcies (USS) up to 60% 250 psi 400 psi to 10,000 psi ambient +/- 0.1 °C 0.1% F.S. 0-600 cc/min 400 psi 500 psi 100 psi (dry) 110 / 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

46/100

AUTOMATED SAMPLE LOADING UNSTEADY STATE AND STEADY STATE PERMEAMETER AND POROSIMETER AT OVERBURDEN PRESSURE (KEYPHI)

PETROPHYSICS

The KEYPHI instrument is a fully automated permeameter and porosimeter used to determine properties of plug sized core samples at reservoir confining pressure. The gas permeability determination is based on the steady state method and unsteady state pressure falloff method whereas the pore volume is determined using the Boyles law technique. The instrument is provided with a unique automatic core sample loading mechanism which can process multiple samples without any human intervention. In addition, the instrument offers reporting and calculation facilities thanks to its user-friendly windows operated software. Klinkenberg slip factor “b”, Klinkenberg corrected permeability, inertial coefficients, sample bulk volume, sample porosity, grain volume are automatically determined and presented on customised report.

FEATURES Confining Pressure Pore Pressure Core diameter Core length Permeability Range Flow meter Porosity Range Sample capacity Helium Nitrogen Air Power

400-10,000 psi 250 psi 1" or 1.5" 0.75" to 3" 0.01md to 10 darcies (SS) and 0.001md to 10 darcies (USS) 0-600 cc/min 0.1 > 60% 13 (1.5” diam. samples) and 16 (1” diam. Sample) 400 psi 500 psi 125 psi (dry) 110 / 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

47/100

LIQUID PERMEAMETER (LIQPERM)

PETROPHYSICS

The Liquid permeameter is dedicated to measure permeability to liquid of plug sized core samples at room conditions. The liquid permeability determination is based on the Darcy’s law and assumes that one phase is present in the core and there is no rock fluid interaction. The instrument is provided with a hassler coreholder, a transparent fluid vessel, a console with pressure digital display, 3 interchangeable burettes for various permeability ranges, an electronic timer for flow rate calculation and an Excel spread sheet calculation template. This low cost apparatus is particular interested for educational purposes.

FEATURES Permeability Range Flow Pressure Confining pressure Temperature Pressure transducer accuracy Air supply Power

0. 1md to 5 darcy up to 100 psi up to 400 psi ambient 0.25% F.S. 250 psi 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

48/100

BENCH TOP PERMEABILITY SYSTEM (BPS 350)

PETROPHYSICS

The BPS350 permeameter is a manually operated system designed for performing simple permeability tests at pore pressure to 5,000 psi with confining pressures to 10,000 psi. The standard system includes a low pulsation HPLC pump for fluid delivery at flow rates from 0.01 to 10 ml/min. Plug core samples are held in a hassler coreholder mounted horizontally. The core holder can accommodate 1.5” diameter core samples one to three inches in length. The system is equipped with one differential pressure transducers and digital readout which has a range of 0-250 psid. A manual bypass valve is used to equilibrate pressure on the transducer preventing damage at high differential pressures. A dome loaded backpressure regulator is utilized to maintain downstream elevated test pressures. A manually operated hydraulic pump is used to generate confining pressure up to 10,000 psi. An optional gas injection can be added to flow nitrogen gas through the core sample to measure gas permeability.

FEATURES Confining pressure Pore pressure Temperature Core diameter Core length Loading type Wetted material Fluid Power

700 bar (10,000psi) 350 bar (5,000psi) ambient 1” or 1’’1/2 1’’ to 3’’ Hassler stainless steel Water and N2 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

49/100

BENCH TOP UNSTEADY STATE RELATIVE PERMEAMETER (BRP 350)

PETROPHYSICS

The semi automated BRP350 allows for the determination of liquid permeability and liquid / liquid relative permeability on plug sized core samples at overburden pressure. The test consists of direct measurement of permeability while injecting oil, water or brine through the rock sample. The system includes two floating piston accumulators, a HPLC pump, a hassler coreholder, an overburden pump, a back pressure regulator and pressure display. The instrument can also be configured for gas / liquid relative permeability measurement.

FEATURES Confining pressure Pore pressure Temperature Core diameter Core length Loading type Wetted material N2 Power

350 bar (5,000psi) 350 bar (5,000psi) ambient 1” or 1’’1/2 1’’ to 3’’ Hassler stainless steel 2,000 psi 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

50/100

BENCH TOP UNSTEADY & STEADY STATE LIQUID – LIQUID RELATIVE PERMEAMETER (SRP 350)

PETROPHYSICS

The SRP350 relative permeameter allows for determination of the liquid / liquid relative permeability on plug sized core samples at overburden pressure using unsteady and steady state conditions. The core saturation is determined by measuring the resistivity of the core sample during the flow test. The flow rates are controlled by the two pumps used to inject simultaneously the fluids is the core sample.

FEATURES Confining pressure Pore pressure Temperature Core diameter Core length Loading type Wetted material N2 Power

350 bar (5,000psi) 350 bar (5,000psi) ambient 1” or 1’’1/2 2’’ to 3’’ Hydrostatic stainless steel 2,000 psi 220 VAC, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

51/100

ELECTRICAL PROPERTIES SYSTEM @ AMBIENT CONDITIONS (EPS-A)

PETROPHYSICS

Complete system used for the determination of resistivity and formation factor of plug sized sample at ambient conditions. The system permits to measure the rock resistivity Ro and the brine resistivity Rw at different frequencies. The cell utilises a two and four electrode design. The platens contact the core end faces under a constant pneumatic pressure up to 6 bar. This minimises contact resistance artefacts which are often found where a screw or jack mechanism is used to load the sample onto the electrode platens. The cell is provided with a plastic cover box to minimise core saturation changes. The instrument also includes a dip conductivity probe and a becher to measure the brine resistivity. An LCR meter is used to monitor the core and brine resistance and capacitance.

FEATURES Core diameter Core Length Resistivity measurement Max pressure Temperature Power supply Air

1” and 1.5” up to 3” 2 and 4 electrodes Atmospheric Room condition 220 VAC 50 Hz 150 psi

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

52/100

ELECTRICAL PROPERTIES SYSTEM @ OVERBURDEN PRESSURE (EPS 700)

PETROPHYSICS

The EPS 700 is used for the measurement of rock resistivity for both fully and partially brine saturated core samples at overburden pressure. The system includes a hydrostatic electrical coreholder, with hand pump for confining pressure generation, a pore pressure control panel for core desaturation and a resistivity meter for 2 and 4 points core resistance measurement. The system can be configured for multi sample configurations.

FEATURES Core diameter Core Length Resistivity measurement Overburden pressure Temperature Power supply Air

1” and 1.5” up to 3” 2 and 4 electrodes 700 bar (10,000 psi) Room condition 220 VAC 50 Hz 150 psi

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

53/100

EDUCATIONAL CAPILLARY PRESSURE CELL

PETROPHYSICS

The educational capillary pressure cell enables to desaturate one consolidated core sample by the porous plate method. Data obtained can be used to calculate capillary pressure versus saturation curves. A high precision weighing balance can be used for core saturation measurement. The capillary pressure cell is manufactured from stainless steel and at its base is equipped with a ceramic plate used as a semi permeable porous plate. The desaturation cell consists of a pressure vessel, with an easy opening lid, o’rings seals, outflow tube assemblies and pressure control panel. A ceramic plate is provided with the cell withstanding 10 bar pressure. The control panel includes a digital pressure display, two low and high range pressure regulators and a set of control valves.

FEATURES Diameter Height Maximum desaturation process Minimum desaturation process Ceramic plate pressure Wetted materials Electrical requirements Air Pressure requirements

40 mm 80 mm 200 psi 0.1 psi 10 bar 316 Stainless steel 220 VAC, 50 Hz 0- 150 psi (10 bar)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

54/100

MULTI SAMPLE CAPILLARY PRESSURE CELL

PETROPHYSICS

The multiple sample desaturation cell enables to desaturate a set of consolidated core samples by the porous plate method. Data obtained can be used to calculate capillary pressure versus saturation curves. A high precision weighing balance can be used for core saturation measurement. The multiple sample desaturation cell is manufactured from stainless steel and is equipped at its base with a large ceramic plate used as a semi permeable porous plate. The desaturation cell consists of a pressure vessel, with an easy opening lid, clamping bolts, o’rings seals, outflow tube assemblies and pressure control panel. Three ceramic plates are provided with the systems withstanding each 3 bar, 5 bar and 15 bar pressure. The control panel includes a digital pressure display, two low and high range pressure regulators and a set of control valves. A gas humidifier is also provided to insure minimum evaporation during the desaturation process.

FEATURES Diameter Maximum desaturation process Minimum desaturation process Ceramic plate pressure Wetted materials Electrical requirements Air Pressure requirements

300 mm 200 psi 0.1 psi 3 bar, 5 bar and 15 bar 316 Stainless steel 220 VAC, 50 Hz 0- 200 psi (15 bar)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

55/100

CAPILLARY PRESSURE REFRIGERATED CENTRIFUGE (RC4500)

PETROPHYSICS

The RC4500 is a refrigerated centrifuge modified to enable rapid determination of capillary pressure characteristics on six core samples simultaneously. It can also be utilized for rapid sample preparation to restore state conditions for subsequent testing in various test equipment. Custom designed sample chambers offer the ability to spin core plug samples up to 1.5 inches in diameter at rotational speeds up to 4,500 RPM. It includes a rotor and drainage cells which can accommodate either 1”, or 1.5” diameter cores. A digital speed control with the ability to ramp speeds at specified intervals and a precision temperature control system is included. An overtemperature setpoint stops the centrifuge if the temperature exceeds the setpoint by a specified value. The system is also equipped with a sensor for rotor imbalance. It is equipped with a digital camera system that allows to user to measure the displaced fluid volumes in each of the cells sequentially.

FEATURES PC range : Oil-water drainage : Oil-water imbibition: Air-water drainage: Air-water imbibition:

0 to 6.2 bar (+90 psi) 0 to -8.4 bar (– 121 psi) 0 to 20.9 bar (+303 psi) 0 to -28.1 bar (– 407 psi)

Speed regulation: Temperature: Speed: Large radius: Power supply:

± 1 rpm 5°C (@speed = 0) to +90°C from 200 up to 4,500 RPM 26 cm 400 V 3 ~ + N

BENEFITS Fast capillary pressure run (1 to 2 days)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

56/100

CAPILLARY PRESSURE MERCURY SYSTEM (CPM 140)

PETROPHYSICS

Manual operated system for the measurement of capillary pressure and pore morphology. Based on Purcell method, mercury is injected into plug sized samples at know volume from vacuum to 2,000 psi (140 bar). The instrument uses a hand operated pump for mercury injection and a coreholder equipped with an opening windowed chamber cap for easy loading / unloading operations and mercury level visualization. The control panel includes the pore pressure regulator, the pore pressure transducer with the digital display and a vacuum manometer.

FEATURES Pressure range Temperature Core Diameter Core length Vacuum pumping speed Final vacuum pressure Power supply Nitrogen source

up to 140 bar (2,000 psi) ambient 1” or 1.5” up to 3 inches 2.5 m3/h 10-3 mbar. 220 VAC, 50Hz 2,000 psi

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

57/100

DIGITAL CORE PHOTOGRAPHY SYSTEM (DCP)

PETROPHYSICS

The fully automated core photography system is designed for complete core photography and archiving purposes, producing high quality white and ultraviolet colour images of full diameter whole or slabbed core samples. The operator positions the core samples on a four rows rack and a digital camera mounted above the core samples under white or ultra violet lighting takes a high resolution picture. The images are then automatically digitised, displayed and recorded in the high speed computer. The software includes calibration functions for the camera, image processing capabilities as well as file compression, storage and transfer facilities. The innovative concept is in the use of a digital camera which can produce very high resolution color images up, avoiding the risk of deformed images.

FEATURES Camera type Camera resolution File size Interface Internal PC hard drive Maximum frame area Data storage on CDROM Weight Power supply

35 mm Full frame 5616 x 3744 pixels 21 Megapixels USB 80 GB 600 mm x 900 mm RAW, JPG 200 kg 220 VAC , 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

58/100

PETROPHYSICS

SPECIAL CORE ANALYSIS

Core Flood System

Formation Damage

Capri

Rock Compressibility

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

59/100

CORE FLOOD SYSTEM FOR EOR STUDIES (CFS 700)

PETROPHYSICS

The CFS 700 system provides a versatile facility to carry out core flood and fluid flow tests studies at reservoir conditions of temperature and pressure. The core flood and fluid tests allow for the evaluation of the effect of different fluids on rock permeability such as brine sensitivity, return permeability, critical flow velocity, acid stimulation, EOR tests (secondary and tertiary water flooding, polymer injection). The computer controlled system is provided with a unique software that allows for operation both manual and automatic modes where all key components can be controlled including pump, valves, video capturing and data acquisition. A test sequencer also permits to program and run test sequences automatically. The coreholder, air operated valves, produced fluid separator if selected and necessary plumbing are mounted in an airbath that has been designed to provide easy access of all components. Several features can be used to extend the capabilities of the system. Among them, the automated back pressure regulator provides a very stable pressure control with fast response to pressure fluctuations and phase transition. It can be used for single and multiphase flow system. The automatic confining pump generates and maintains automatically a net overburden pressure thus avoiding to control pressure changes during heating and cooling steps. The unique video separator provides an extreme accuracy of the volume of brine, oil and gas produced during the flow tests at reservoir conditions.

FEATURES Confining pressure Pore pressure Maximum working temperature Core diameter Core length Fluid flow rate Wetted parts Power supply Air Pressure requirements

700 bar (10,000 psi ) depends on the injection pump model 150°C 1.5” other upon request 1”to 3” other upon request depends on the injection pump model Stainless steel, other type upon request 220VAC, 50Hz 7 bar (100 psi)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

60/100

UNSTEADY STATE RELATIVE PERMEAMETER (AUTOFLOOD 700)

PETROPHYSICS

The AUTOFLOOD 700 system provides a versatile facility to carry out unsteady state relative permeability studies for liquid/liquid and liquid/gas at reservoir conditions of temperature and pressure. The standard configuration allows for liquid /liquid tests at constant flow rate and liquid/gas tests at constant pressure. A gas line permits to inject gas at constant pressure. The computer controlled system is provided with a unique software that allows for operation both manual and automatic modes where all key components can be controlled including pump, valves, video capturing and data acquisition. A test sequencer also permits to program and run test sequences automatically. The coreholder, air operated valves, produced fluid separator and necessary plumbing are mounted in an airbath that has been designed to provide easy access of all components. The automated back pressure regulator provides a very stable pressure control with fast response to pressure fluctuations and phase transition. It can be used for single and multiphase flow system. The automatic confining pump generates and maintains automatically a net overburden pressure thus avoiding to control pressure changes during heating and cooling steps. The unique video separator provides an extreme accuracy of the volume of brine, oil and gas produced during the flow tests at reservoir conditions.

FEATURES Maximum confining pressure Maximum pore pressure Maximum gas pressure Maximum working temperature Core diameter Core length Material Power supply Air Pressure requirements

700 bar (10,000 psi) 700 bar (10,000 psi) 200 bar (3,000 psi) 150°C 1"1/2 other upon request 1” to 3” other upon request Stainless steel 220VAC, 50Hz 7 bar (100 psi)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

61/100

STEADY STATE AND UNSTEADY STATE RELATIVE PERMEAMETER SYSTEM (RPS 700)

PETROPHYSICS

The RPS 700 system provides a versatile facility to carry out unsteady state and steady state relative permeability studies for liquid/liquid and liquid/gas at reservoir conditions of temperature and pressure. The standard configuration allows liquid /liquid and liquid/gas flow tests to be conducted at constant flow rate. An optional gas line permits to run unsteady state gas/liquid permeability tests at constant pressure. The computer controlled system is provided with a unique software that allows for operation both manual and automatic modes where all key components can be controlled including pump, valves, video capturing and data acquisition. A test sequencer also permits to program and run test sequences automatically. The coreholder, air operated valves, produced fluid separator and necessary plumbing are mounted in an airbath that has been designed to provide easy access of all components. The unique high temperature recirculating triple pump system presents an unprecedented solution to generate continuous, pulse free fluid flow rate of one or more fluids through a sample while maintaining a constant pressure at the outlet of the sample. The automatic confining pump generates and maintains automatically a net overburden pressure thus avoiding to control pressure changes during heating and cooling steps. The video separator also provides an extreme accuracy of the volume of brine, oil and gas produced during the flow tests at reservoir conditions.

FEATURES Maximum confining pressure Maximum pore pressure Maximum working temperature Core diameter Core length Flow rate Material Power supply Air Pressure requirements

700 bar (10,000 psi) 700 bar (10,000 psi) 150°C 1"1/2 other upon request 1” to 3” other upon request 0.005 to 50 cc/min Stainless steel 220VAC, 50Hz 7 bar (100 psi)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

62/100

XRAY SCANNER FOR IN-SITU SATURATION MONITORING

PETROPHYSICS

The Xray scanner is an add-on module to the relative permeability RPS700 rig and allows for monitoring the in situ fluid saturations and distribution along the length of the core. The standard configuration allows for liquid /liquid and liquid/gas saturation determination. The Xray scanner allows for measuring the attenuation of an X-ray beam sent through a core sample to determine the phase saturation and saturation distribution along the length of the core sample. The X-ray detector and generator are mounted on a motor driven table equipped with a high accuracy position encoder. A composite coreholder is be used for these tests to avoid X-ray absorption.

FEATURES Maximum confining pressure Maximum pore pressure Maximum working temperature Core diameter Core length X-ray source Wetted parts Power supply Air Pressure requirements

700 bar (10,000 psi) 700 bar (10,000psi) 150°C 1”5 other upon request 4” to 12” other upon request 120 kV, 4 mA Stainless steel 220VAC, 50Hz 7 bar (100 psi)

BENEFITS The core sample temperature is homogenous all along the core.

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

63/100

PETROPHYSICS

FORMATION DAMAGE AND WELL TREATMENT EVALUATION SYSTEM (FDS 350) The FDS350 system enables to perform (a) liquid permeability measurement, (b) static filtration tests, (c) mud invasion evaluation and (d) stimulation tests on a formation sample at reservoir conditions of temperature and pressure. This instrument can be configured for the evaluation of the effect of different fluids on rock permeability such as drilling fluids (water-based or oilbased mud), cement effluents, chemical wash treating fluids and acid corrosive treating fluids. Initial permeability, return permeability, brine sensitivity, critical flow velocity, acid stimulation, mud filtrate invasion can be monitored with this system. Drilling mud tests are performed under realistic field conditions by flowing the fluids tangentially to the face of the core, thanks to a special leak-off core holder. The system can be configured with a mud recirculation pump to perform dynamic filtration tests so as to study erosion effects induced by the fluid flowing across the core face which contains proppant and other particulates. The mud pump flow rate of 6 l/min max ensures an efficient shear rate to simulate the real operating conditions. The computer controlled system is provided with a unique software that allows for operation both manual and automatic modes where all key components can be controlled including pump, valves and data acquisition. A test sequencer also permits to program and run test sequences automatically. The coreholder, air operated valves, mud pump and necessary plumbing are mounted in an airbath that has been designed to provide easy access of all components.

FEATURES Maximum confining pressure Maximum pore pressure Maximum mud pressure Maximum working temperature Core diameter Core length Mud flow rate Material Power supply Air Pressure requirements

700 bar (10,000 psi) 350 bar (5,000 psi) 350 bar (5,000 psi) 150°C 1.5” other upon request 2 to 4” other upon request up to 6 liter/min (option) Stainless steel, Titanium, hastelloy 220VAC, 50Hz 7 bar (100 psi)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

64/100

CAPILLARY PRESSURE AND RESISTIVITY INDEX SYSTEM (CAPRI)

PETROPHYSICS

The CAPRI system is dedicated to the determination of the capillary pressure curves (positive and negative) and the electrical resistivity index as a function of core sample saturation at reservoir conditions. Saturation exponent “n”, formation factor and cementation exponent “m” are also calculated. The instrument consists of a core holder furnished with hydrophobic and hydrophilic ceramics and electrodes pattern for resistivity measurement, an automated pumping system for fluid control and a resistivity cell for brine resistivity measurement. The whole is housed in a temperature controlled air bath.

FEATURES Maximum confining pressure Max pore pressure Working temperature Capillary pressure range Core length Core diameter Power supply Brine wetted material

700 bar (10, 000 psi) 700 bar (10,000 psi) up to 150°C 10 to +10 bar (145 psi) 2” up to 3” 1 ½” other upon request 220VAC, 50Hz stainless steel

BENEFITS Measurement are made at reservoir conditions of pressure and temperature Direct capillary pressure measurement High temperature pump located in the controlled temperature air bath to reduce volume measurement error induced by temperature fluctuations. Multiple core samples configuration available

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

65/100

ROCK COMPRESSIBILITY SYSTEM (RCS 700)

PETROPHYSICS

The RCS 700 apparatus is designed to monitor pore and bulk volume changes under various levels of radial and axial confining pressures at reservoir temperature. The apparatus consists of a triaxial core holder located in a constant temperature air bath to restore the reservoir conditions on the core sample. The pump cylinder is used to generate and control the pore pressure while the other two pump cylinders are used to generate the axial and radial confining pressures. The volume variations of fluid injected into or expelled from the core sample can be monitored with an extreme accuracy. Automated tests can be programmed to perform a number of measurements at different steps of pressure and temperature without user’s intervention.

FEATURES Core Diameter Core Length Max pore pressure Max axial / radial confining pressure Stroke volume of pump Working temperature Volume measurement accuracy Pressure measurement accuracy Material Power supply

1 1/2" other upon request 1 to 3” other upon request 700 bar (10,000 psi) 700 bar (10,000 psi) 100 cc ambient to 150° C 0.001 cc 0.1 % Stainless steel 220VAC, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

66/100

ATMOSPHERIC ACOUSTIC VELOCITY SYSTEM (AVS A)

PETROPHYSICS

The AVS A allows for the measurement of acoustic velocity of a core sample at atmospheric pressure and ambient temperature. It is used to propagate compressional and shear waves through core samples, calculate acoustic velocity and determine dynamic elastic constants such as the dynamic moduli, Young’s, bulk and shear, along with Poisson’s ratio. The system consists of an atmospheric coreholder, acoustic transducer assemblies, acoustic Pulser / receiver and digital oscilloscope.

FEATURES Operating pressure Operating temperature Core sample diameter Core sample length Center frequency Mode Power supply

Atmospheric up to 50°C 1” and 1.5” other upon request 1 to 3” other upon request 500 KHz compressional (P) and shear (S1 & S2) 220VAC, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

67/100

OVERBURDEN ACOUSTIC VELOCITY SYSTEM (AVS 700)

PETROPHYSICS

The AVS 700 allows for the measurement of acoustic velocity of a core sample under a wide range of pore and confining pressures. It is used to propagate compressional and shear waves through core samples, measure pore pressure, confining pressure and temperature, calculate acoustic velocity and determine dynamic elastic constants such as the dynamic moduli, Young’s, bulk and shear, along with Poisson’s ratio. The system consists of fully equipped pressure vessel, acoustic transducer assemblies, confining pressure controller, pore pressure controller, acoustic Pulser / receiver and digital oscilloscope.

FEATURES Operating pressure Operating temperature Core sample diameter Core sample length Center frequency Mode Power supply

Up to 700 bar (10,000 psi) up to 50°C 1.5” other upon request 1 to 3” other upon request 500 KHz compressional (P) and shear (S1 & S2) 220VAC, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

68/100

AUTOMATED HP-HT ACOUSTIC VELOCITY SYSTEM (AVS 700-HT)

PETROPHYSICS

The AVS 700-HT apparatus allows for the measurement of acoustic velocity of a core sample under various levels of pore pressure and radial/axial confining pressures at reservoir temperature. The apparatus permits to propagate compressional and shear waves S1 and S2 through core samples, generate and measure the pore pressure and confining pressure, calculate acoustic velocity at reservoir conditions and determine dynamic elastic constants (Poisson ratio and Young modulus). The system consists of three automated pumps and a fully equipped acoustic triaxial coreholder housed in a constant temperature air bath to restore the reservoir conditions on the core sample. One pump cylinder is used to generate and control the pore pressure while the other two pump cylinders are used to generate the axial and radial confining pressures. A pulser-receiver is used to produce an electrical pulse to excite a piezoelectric transducer and an oscilloscope measures the travel time of the pulse between the two transducers. This data is then used to calculate the acoustic velocity of the core sample.

FEATURES Operating pressure Operating temperature Core sample diameter Core sample length Center frequency Mode Power supply

Up to 700 bar (10,000 psi) up to 150°C 1.5” other upon request 1 to 3” other upon request 500 KHz compressional (P) and shear (S1 & S2) 220VAC, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

69/100

AGING CELL APPARATUS (ACA 700)

PETROPHYSICS

The apparatus is designed for aging core samples with crude oil so as to restore its reservoir wettability before being used for a SCAL study. The base version is delivered with five core units. The aging method entails first saturating a cleaned (and thus water wet) core plug with brine. The brine is then displaced by crude oil until representative initial water saturation is achieved. During this process the smaller pores remain water –filled, whereas the oil invades the remainder of the pore space, leaving thin water films on the pore walls and in crevices. Finally, the core containing crude oil and connate water is left for many weeks at reservoir temperature and pressure. It is at this stage that wettability changes may occur in the oil-invaded pores. However, these changes are dependant upon the stability of the water wet films, trapped between the rock surface and the oil. The pore walls can only become oil-wet if contacted by oil due to the rupture of these films. In this case the core will have achieved a mixed wettability state status.

FEATURES Operating pressure Operating temperature Core sample diameter Core sample length Fluid flow rate Wetted part Air requirement Power supply

up to 700 bar (10,000 psi) up to 150°C 1” and 1.5” 1 to 3” up to 10 cc/min Stainless steel 2,000 psi 220VAC, 50Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

70/100

PETROPHYSICS

COREHOLDERS

Hassler CH

Triaxial CH

Leakoff CH

Stands

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

71/100

HASSLER COREHOLDER (HAS SERIES)

PETROPHYSICS

The HAC Series core holders are standard Hassler type core holders used for fluid flow testing. With the coreholder assembled and the sleeve in place the core is inserted into the loading end. The platen is then pushed in and held in place by the cap which can be screwed on by hand and allows 50 mm adjustement. Further adjustment is possible with the use of interchangeable spacers fitted to the loose platen. An inlet and outlet distribution plug allows fluids and gases to be injected through the core sample. A unique feature of the HAC series core holder is that the sleeve remains in place and the core is loaded from one end without having to drain or refill the confining fluid. By releasing the confining radial pressure and unscrewing the end plug, the core sample can be easily removed without exposing it to the annulus fluid. The core holders can be provided to have interchangeable core diameters.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Fitting: Core diameter: Core length: Wetted parts: Sleeve material Inlet port: Outlet port:

HAC series 5,000 psi (Max) Ambient or 150°C NPT, Autoclave or HIP Customer specified Customer specified Stainless steel, Hastelloy, titanium Viton As request As request

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

72/100

HYDROSTATIC COREHOLDER (HYC SERIES)

PETROPHYSICS

The HYC Series core holders are standard hydrostatic type core holders in which radial and axial confining pressures are common. These core holders are routinely used for gas and liquid permeability testing and water flooding experiments. The coreholder has a fixed platen at one end over which the rubber sleeve is mounted and located in the other end of the sleeve is a floating platen connected via a ¼” diameter tubing passing through the outside. For variable length cores, this design insures solid contact between the platen and core sample. To change a core sample the confining fluid must be drained off and the knurled screwed ring removed by rotating anti clockwise by hand. This will withdraw the fixed platen together with the sleeve, core and floating platen. After removal of the two platens from the sleeve the core can be withdrawn. Loading a new core sample is carried out in the reverse order. The advantage of this type of coreholder is that the overburden pressure acts on the end of the core as well as the diameter. The coreholder can be equipped with a number of pressure taps molded in the sleeve at discrete locations required by the end user. This design allow to monitor the pressure drop along the length of the core sample during fluid flow tests. Electrical pressure tap can also be provided to monitor the resistivity of the core sample during a permeability test.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Fitting: Core diameter: Core length: Wetted parts: Sleeve material : Inlet port: Outlet port: Pressure tap :

HYC series 5,000, 10,000 psi, 15,000 psi Up to 150°C NPT, Autoclave or HIP Customer specified Customer specified Stainless steel, Hastelloy, titanium Viton As request one As request

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

73/100

TRIAXIAL COREHOLDER (TRC SERIES)

PETROPHYSICS

The TRC Series core holders are standard triaxial type core holders in which radial and axial loading are independent. These core holders are routinely used for fluid flow experiments. A unique feature of the TRC series core holder is that the sleeve remains in place and the core is loaded from one end without having to drain or refill the confining fluid. Independent axial pressure is applied via a floating distribution plug. An inlet and outlet distribution plug allows fluids and gases to be injected through the core sample. A unique feature of the TRC Series core holder is that the holder does not need to be completely disassembled to remove the core sample. By releasing the confining radial and axial pressure and unscrewing the eng plug, the core sample can be easily removed without exposing it to the annulus fluid. The coreholder can be configured for hassler loading, hydrostatic loading or triaxial loading.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Fitting: Core diameter: Core length: Wetted parts: Sleeve material : Inlet port: Outlet port:

TRC series 5,000, 10,000 psi, 15,000 psi Up to 150°C NPT, Autoclave or HIP Customer specified Customer specified Stainless steel, Hastelloy, titanium Viton As request As request

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

74/100

LEAKOFF COREHOLDER (LEC SERIES) The LEC Series core holders are mainly used for static and dynamic filtration tests so as to study erosion effects induced by the fluid flowing across the core face which contains proppant and other particulates. The coreholder features a special head that allows the upper face of the core sample to be exposed to invasion fluids. The fluids can be injected from both ends of the core holder then simulating the wellbore and the reservoir side. The coreholder can be equipped with a number of pressure taps molded in the sleeve at discrete locations required by the end user. This design allow to monitor the pressure drop along the length of the core sample during fluid flow tests.

PETROPHYSICS

.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Fitting: Core diameter: Core length: Wetted parts: Sleeve material : Inlet port: Outlet port: Pressure taps :

LEC series 5,000, 10,000 psi Up to 150°C NPT Customer specified Customer specified Stainless steel, Hastelloy, titanium Viton As request As request As request

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

75/100

QUICK RELEASE COREHOLDER (QRC SERIES)

PETROPHYSICS

The QRC Series core holders allows for the core to be loaded without the complete disassembly of the coreholder. The core loading is achieved using an innovative ¼ turn fast release bayonet mechanism. The coreholder is configured for hassler loading. The sleeve remains in place and the core is loaded from one end without having to drain/refill the confining fluid which can be nitrogen or hydraulic oil. This avoids damage to the sleeve which can occur with assembly and disassembly. Operation is much easier and quicker and leads to higher throughput when tests of short duration are being carried out.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Fitting: Core diameter: Core length: Wetted parts: Sleeve material Inlet port: Outlet port:

QRC series 400 psi, 1000 psi Ambient or up to 80°C NPT Customer specified Customer specified Stainless steel Nitrile 1 1

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

76/100

TRANSPARENT COMPOSITE COREHOLDER (TCC SERIES)

PETROPHYSICS

The TCC Series core holders are standard hydrostatic type core holders. These core holders are used for gas and liquid permeability testing with in situ saturation monitoring. The core holder uses a thin aluminium liner which is over wrapped with carbon fibre composite and epoxy to avoid important loss of X-ray. Spiral fluid distribution grooves on core inlet are incorporated to minimise capillary end effects. The coreholder can be provided with an heating system which heats and re-circulates the confining fluid through the annular confining chamber for optimal temperature homogeneity.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Fitting: Core diameter: Core length: Wetted parts: Sleeve material Inlet port: Outlet port:

TCC series Up to 10,000 psi, Ambient or up to 150°C NPT Customer specified Customer specified Stainless steel, Hastelloy, titanium Viton As request As request

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

77/100

ACOUSTIC VELOCITY COREHOLDER (AVC SERIES)

PETROPHYSICS

The AVC Series core holders are standard triaxial type core holders in which radial and axial loading are independent. These core holders are routinely used for acoustic velocity measurement at reservoir conditions. The coreholder features a pair of acoustic transducers that propagate compressional and two plane-polarized shear waves through the core sample. The triaxial loading insures a proper surface contact between the transducer and the core. An inlet and outlet distribution plug allows fluids to be injected through the core sample. The coreholder does not need to be completely disassembled to remove the core sample. A tool permits to orientate easily the P&S1,S2 transducer before the acoustic velocity measurement takes place.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Center frequency Fitting: Core diameter: Core length: Wetted parts: Sleeve material Inlet port: Outlet port:

AVC series 10,000 psi, 15,000 psi Ambient or 150°C 500 KHz NPT, Autoclave or HIP Customer specified Customer specified Stainless steel Viton 1 1

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

78/100

ELECTRICAL RESISTIVITY AND CAPILLARY PRESSURE COREHOLDER (ECP SERIES)

PETROPHYSICS

The ECP Series core holders are standard hydrostatic type core holders. These core holders are routinely used for electrical resistivity and capillary pressure at reservoir conditions. The coreholders feature both water wet and oil wet porous ceramics placed between the flow distribution plugs and the core sample. Four electrodes have been molded directly into the sleeves and are used to measure the resistivity of the sample. Two of them are provided with metal ring placed into the sleeve along the core length at one inch spacing between the rings. The other two electrodes are in contact with the distribution plugs which are electrically isolated from the rest of the coreholder.

FEATURES Performance specifications Operating pressure rating: Operating temperature: Resistivity measurement Capillary pressure Connection Core diameter: Core length: Wetted parts: Sleeve material Inlet port: Outlet port:

ECP series 10,000 psi, Ambient and up to 150°C 2 and 4 points Positive and negative NPT Customer specified Customer specified Stainless steel Viton 2 1

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

79/100

HEATING SYSTEM (HES SERIES)

PETROPHYSICS

The electrical heating system can be provided to heat and maintain homogeneous temperature in the core sample. The system uses two half heating shelves maintained by two clamps that fit the shape of the coreholder in order to provide the highest heat efficiency. A digital temperature controller is used to enter, display and regulate the temperature . A thermocouple probe is used to measure the temperature of the coreholder body.

FEATURES Performance specifications Operating temperature: Temperature accuracy: Power:

HES series Ambient to 150°C 0.1 °C 220 VAC, 50 Hz,

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

80/100

STANDS (STA SERIES)

PETROPHYSICS

A number of stands are available depending on the End user’s requirement. Simple to most complicated designs can be proposed. The stand can be mounted inside or outside of the airbath. The stand can also be configured in a bench top or bench floor version.

FEATURES Performance specifications

STA series

Coreholder position:

Fixed Horizontal, Fixed horizontal and vertical, Swivelling

Operating temperature:

Ambient and up to 150°C

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

81/100

PETROPHYSICS

CORE ANALYSIS COMPONENTS

Level Tracker

BPR

Vacuum Pump

Pressure Generator

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

82/100

LEVEL TRACKER SEPARATOR (LTS SERIES)

PETROPHYSICS

Designed to measure the volume of liquid produced during a process at ambient conditions. The device is made of a precision bore calibrated glass liquid collector, a motor driven level detector composed of a tracking fork with 2 optical fibers (light path of emitter and sensor) and a converter (light / voltage), an encoder to log the liquid level and a computer interface to control the instrument and to log and display the liquid volume versus time.

FEATURES Temperature Collector capacity Volume accuracy Wetted parts

ambient 100 ml or 300 ml 0.1 ml glass

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

83/100

DUAL LEVEL TRACKER (DLT SERIES)

PETROPHYSICS

Designed to measure the volumes of the two liquid phases produced during a process at ambient conditions. The device is made of a precision bore calibrated glass liquid collector and two motor driven level detector used to monitor the first water / oil interface and the second oil / Gas interface. Each detector is composed of a tracking fork with 2 optical fibers (light path of emitter and sensor) and a converter (light / voltage), an encoder to log the liquid level and a computer interface to control the instrument and to log and display the liquid volume versus time.

FEATURES Temperature Collector capacity Volume accuracy Wetted parts Power supply Weight Dimensions (HxWxL)

ambient 100 ml or 300 ml 0.1 ml glass 220 VAC 50 Hz 30 kg 800 mm x 250 mm x 250 mm

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

84/100

AMBIENT CONDITIONS TWO PHASE VIDEO SEPARATOR (VSE -A)

PETROPHYSICS

The video separator is a precision device used for separating and determining the oil, brine or gas volumes that are produced from a core sample during a two phase relative permeability test. It consists of a separation bore used for collecting and separating produced fluids under gravity and a measurement bore used for visualising the two phases fluid interface at room conditions. The measurement bore consists of a glass tube to allow for sample visibility. Placing a light behind the tube allows easy discernment of the two phases interface level. Measurement of produced fluids during the displacement test is performed with a video camera which monitors the position of the interface of the two fluids produced from the core sample in the measurement bore of the separator. The position of the interface is directly proportional of the volumes of fluids produced from the core sample and so of the change in the core saturation. The high resolution camera is equipped with an integrated zoom and a back lighting installed in the rear side of the tube. The camera is connected to the computer station so that the image of the fluid can be displayed and recorded on the PC. The video software incorporates facilities which enable to detect automatically the liquid/ liquid and gas/ liquid interface and so derive the volumes of produced fluids from the core and so the changes in the core saturation.

FEATURES Max pressure ………………… Max temperature……………… Max volume change………….. Volume accuracy…………...… Material………………………. Measurement resolution…….. Minimum field of view………. CDD colour camera……….…. Lighting ……………………... Power………………………...

Atmospheric pressure up to 40 °C 30 ml 0.01 ml Glassware 0.02 mm 50 mm 440,000 pixels 20 watts 230 VAC, 50, 60 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

85/100

HP-HT TWO PHASE VIDEO SEPARATOR (VSE 700)

PETROPHYSICS

The apparatus is designed to separate the two phase fluids produced from the core at reservoir conditions. It consists of a separation bore used to collect and separate produced fluids under gravity and a measurement bore used to visualise the two phases fluid interface at reservoir conditions. The measurement of produced fluids is performed with a video tracker designed to monitor the position of the interface of the two fluids which is directly proportional of the volumes of fluids produced from the core sample. The video tracker system comprises a high resolution camera equipped with an integrated zoom, a back lighting installed in the rear side and a motorized linear stage that is used to position the camera relative to the fluid interface to be measured. The linear stage and the camera are both connected to the computer station so that the image of the fluid can be displayed and recorded on the PC. The video software incorporates facilities which enable to detect automatically the liquid/ liquid and gas/ liquid interface and so derive the volumes of produced fluids from the core and so the changes in the core saturation.

FEATURES Max pressure ………………… Max temperature……………… Max volume change………….. Volume accuracy…………...… Material………………………. Measurement resolution…….. Minimum field of view………. CDD colour camera……….…. Lighting ……………………... Power………………………...

10,000 psi 150 °C 100 ml, option: 300 ml 0.01 ml Sapphire, Stainless steel, option: Titanium 0.02 mm 10 mm 440,000 pixels 150 watts 230 VAC, 50, 60 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

86/100

WET GAS METER (WG SERIES)

PETROPHYSICS

Designed to measure the volume of gas produced during a process at ambient conditions such as gas-liquid relative permeability. The meter is complete with thermometer, spirit level, levelling feet and gas connections. An option computer interface is available to acquire and display the gas volume versus time.

FEATURES Temperature Pressure Capacity Scale Maximum pressure Flow range Maximum capacity

Ambient Atmospheric 25 dm3 (i.e. 0.25 litres) per revolution 0.001 dm3 65 mbar 30 to 90 litres per hour +/- 0.5% 99,999 litres

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

87/100

CAPILLARY SIGHT GLASS TUBE

PETROPHYSICS

The capillary sight glass tube provides a means to visually confirm miscibility of displaced fluids during dynamic processes such as slim tube miscibility experiments and core displacement test. The cell is made with a glass capillary tube embraced with two flanges at its ends.

FEATURES Max pressure Temperature Wetted parts

10,000 psi up to 150°C Stainless steel, sapphire

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

88/100

BACK PRESSURE REGULATOR (BPR)

PETROPHYSICS

Vinci offers back pressure regulators designed to regulate the pressure in fluid flow studies. The BPR consists of two chambers separated by a piston with a needle connected to it on the lower side. The upper chamber receives the gas dome pressure and the lower chamber the process pressure. The BPR acts a comparator. When the dome pressure is higher than the process pressure the needle seals off the pressure and maintains the pressure. Inversely when the process pressure exceeds the dome pressure the needle opens up and the excess process fluid flows out. That way, on continuous flow these 2 stages are looped continuously and the process pressure is balanced to the dome controlled constant value.

FEATURES Maximum pressure Flow rate Max Temperature Wetted part material Port connection

10,000 psi 0.01 to 25 cc/min 150°C stainless steel 1/8”

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

89/100

ELECTRICAL ISOLATOR (EI 700) The EI 700 is designed to electrically isolate one side of a core holder from the other when placed in a non-conductive fluid stream. It can be used for reservoir condition electrical properties during a relative permeability or a capillary pressure displacement test.

PETROPHYSICS

FEATURES Maximum pressure: 10,000 psi Max Temperature: 150°C Internal volume: less than 1 cc Wetted part material: stainless steel, peek Port connection: 1/8”

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

90/100

AUTOMATED CONFINING PRESSURE CONTROLLER (ACP 700)

PETROPHYSICS

The ACP 700 is designed to generate and maintain automatically a constant confining pressure requested during core studies. It can also be used to maintain a constant differential pressure between the pore pressure and confining pressure. The system consists of a positive displacement pump of 100 cc capacity and 10,000 psi pressure, an automatic dual valve, a fluid reservoir and two pressure transducers for pore and confining pressure control.

FEATURES Confining pressure Pore pressure Pump cylinder capacity Air requirement Tubing connector Power Wetted parts

up to 10,000 psi up to 10,000 psi 100 cc 100 psi 1/8” 220 VAC 1 Ph, 50 Hz Stainless steel

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

91/100

FLOATING PISTON ACCUMULATOR (FPA SERIES)

PETROPHYSICS

The floating piston accumulators are available in a range of different volume and pressure rating. These can be constructed in different material such as 316 stainless steel, aluminium, titanium or hastelloy. The fluid seals may either be the standard Viton / Nitrile ‘O’ rings and PTFE back up ring.

FEATURES Pressure Temperature Cell volume Material

5,000 psi, 10,000 psi or 15,000 psi Ambient to 150°C (300 °F) 100 cc, 300 cc, 500 cc, 700cc, 1,000cc, 2,000 cc, 5000 cc 316 stainless steel, aluminium, titanium or hastelloy

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

92/100

MIXER CYLINDER (MC SERIES)

PETROPHYSICS

The MC series are double end piston type cylinders designed to store and mix any kind of fluids at pressure and temperature. The sample fluid is isolated from the secondary driving fluid with a floating piston and a magnetic mixer is located in the mixing sample chamber for proper agitation. The mixer is magnetically coupled to a drive system through the accumulator end cap which incorporates a permanent magnet driven by a direct current motor with variable speed. A mixer controller permits to stop, start and control the speed of the mixer. The cylinder can be operated in either upright or inverted orientation. Both end caps are provided with an inlet/outlet port for fluid introduction or fluid sampling.

FEATURES Model MC 500-10 MC 1000-10 MC 2000-10 MC 500-15 MC 1000-15 MC 2000-15 (1)

Volume ml 500 1,000 2,000 500 1,000 2,000

Pressure psi 10,000 10,000 10,000 15,000 15,000 15,000

Temp. °C 150 150 150 200 200 200

Weight Kg 21 25 35 21 25 35

Length mm 700 750 900 700 750 900

Diameter mm 120 120 150 120 120 150

Material (1) Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel

Thread connection ¼” FNPT ¼” FNPT ¼” FNPT 1/8” FLP 1/8” FLP 1/8” FLP

Titanium material available.

Mixer controller Power requirement…………………… 230 VAC, 50 Hz, 100 W

BENEFITS      

H2S resistant The impeller provides a minimum dead volume Provide rigorous agitation of entire fluid sample Capable of mixing high viscosity samples up to 1,000 cp High speed, allows equilibrium to be reached in minimum time Reduces operating time for establishing phase equilibrium on sample.

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

93/100

FLUID TRANSFER VESSELS (FTV SERIES)

PETROPHYSICS

The fluid transfer vessels uses a glass tube embraced in two end plugs which are held in place with two aluminium tie bars. The glass tube is protected by an external polycarbonate tube in case of failure of the glass. The top end plug can be removed easily to load the fluid in the vessel. The fluid is transferred from the vessel to another accumulator by applying air pressure on the top port while the fluid passes through the bottom port of the vessel.

FEATURES Pressure Volume Material Fluids

150 psi 1,500 cc (other upon request) Glass brine, oil, mud, drilling fluid, etc

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

94/100

HYDRAULIC INTENSIFIER (HI SERIES)

PETROPHYSICS

The HI series are dual cavity cylinders equipped with a low pressure (LP) bore at one end and a high pressure (HP) bore at the other end. The pistons in each cylinder bore are connected by a solid rod. When pressurized fluid enters the larger bore, the fluid in the smaller bore is compressed to a pressure multiplied by the ratio of areas on the two pistons. Consequently, pressures up to 150Kpsi can be achieved by using a commercially available lower pressure (10 Kpsi) pump. Material of construction is either stainless steel or titanium.

FEATURES Model

Ratio

HP end

LP end

HI 2

2 :1

Volume ml 50

Pressure psi 20,000

ID mm 25.46

Stroke mm 98.24

Pressure psi 10,000

ID mm 36

HI 4

4 :1

25

40,000

18.00

98.24

10,000

36

HI 6

6 :1

20

60,000

14.70

117.89

10,000

36

HI 8

8 :1

15

80,000

12.73

117.89

10,000

36

HI 10

10 :1

10

100,000

11.38

98.24

10,000

36

HI 15

15 :1

5

150,000

9.30

73.68

10,000

36

Additional features: Temperature Thread connection Material Weight Length Diameter

ambient ¼” FNPT (Low pressure side ) and ¼” FHP (High pressure side)

Stainless steel or titanium Approx. 22 Kg

600 mm 90 mm to 120 mm depending on the model.

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

95/100

PRESSURE GENERATOR SYSTEM (PGS)

PETROPHYSICS

Designed to provide hydraulic pressure for Hg free fluid transfer at pressure condition. Maximum output is 10,000 psi. The system comes complete with control valves, air driven liquid pump, pressure gauge, air regulator, relief valve and frame.

FEATURES Max outlet pressure Air inlet Wetted parts

10,000 psi 30 to 145 psi (10 bar). Stainless steel,

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

96/100

DIGITAL PRESSURE GAUGE (DPG SERIES)

PETROPHYSICS

The Digital Pressure Gauge series is designed for extremely accurate pressure measurement to meet your most demanding requirements for precision laboratory or field measurement instrumentation. The instrument includes a high precision analog pressure transducer, a rupture disc for over pressure protection, a five digit digital display and a data logging software for automatic data acquisition.

FEATURES Model Pressure range Accuracy Port connection Wetted part Power supply

DPG series up to 10,000 psi (other range available) 0.1% FS

1/8” autoclave type stainless steel 220 VAC 1 Ph, 50 Hz

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

97/100

DEADWEIGHT GAUGE

PETROPHYSICS

Primary pressure standard designed for high pressure calibration applications. The device consists of a vertically mounted precision lapped piston and cylinder assembly. Accurately calibrated masses are loaded onto the piston, which rises freely within its cylinder. These weights balance the upward force created by the application of pressure within the system. Delivered with a carrying case.

FEATURES Model Operation Pressure range Accuracy

Dual piston Oil operated 1 bar (15 psi) to 1,100 bar (16,000 psi) 0.015% RDG

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

98/100

UNINTERRUPTABLE POWER SUPPLY (UPS 16)

PETROPHYSICS

Back-up power protection used in most laboratories against electrical noise, sags, surges and brownouts which affect the sensitivity of the electrical components of the laboratory equipment.

FEATURES Output power capacity Max configurable power Input voltage Output voltage Efficiency at full load Back up time

12,800 Watts / 16,000 VA 12,800 Watts / 16,000 VA 240 V +-1 %, single phase 240 V +-1 %, single phase 90% 6 minutes at full load (12,800 watts) 17 minutes at half load (6,400 Watts)

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

99/100

PETROPHYSICS

OTHER COMPONENTS

Vacuum pump: Based on double stage rotary vane pump and featuring a max pumping speed of 2.5 m3/h and a vacuum rate of 10-3 mbar.

Air compressor: Designed to generate compressed air of 7 to 10 bar when compressed air is not available.

Controlled temperature air bath: Designed to provide homogeneous temperature with extreme accuracy. A large range of air bath is available depending on temperature ranges, dimension and temperature homogeneity accuracy. The air bath can be provided with one or two front and rear doors and with or without windows. Thermostatic bath: Designed to provide heating and cooling source with an accurate regulation.

Fraction collector: Inline effluent fraction collector for collecting up to 70 individual liquid sample fractions automatically on a time or volume basis PH meter: Inline pH probe and meter for monitoring effluent pH as a function of time.

VINCI TECHNOLOGIES Parc de l'Ile, 27B rue du Port, 92022 NANTERRE Phone: 331 41 37 92 20 Fax: 331 41 37 04 76 e-mail: [email protected] http://www.vinci-technologies.com

100/10 0