Variable Displacement Pump H(S)P-10V SERIES 31
• Industrial & Mobile, Single & Thru Shaft Models, H(S)P-10V • 18, 28, 45, 71, 100 & 140 Frame Sizes Available • Same Day Shipment of Units or Parts Orders • DR, DRG, DFR, DFR1, DFLR Controls • SAE & Metric Units • Available series 31 and 52
hydraut.com
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 INDEX Variable Displacement Pump H(S)P-10V, Series 31 Features 1 Technical Data 2 Ordering Code 3 Fluid Operational Conditions 5 Noise Level 6 DR Pressure - Control Data - Dimensions
7
DRG Pressure - Control Data - Remote Control - Dimensions
9
DFR/DFR1 Pressure - Flow Control 10 DFLR Pressure - Flow - Power Control - Dimensions
12
Mounting Dimensions, Size 18, Series 31 Service Ports on Side; Non Through Drive, Models 62N00 and 12N00
14
Mounting Dimensions, Size 28, Series 31 Service Ports at Side and Rear; Non Through Drive
15
H(S)P-10V28 Shaft, Metric Mount, and Port Dimensions
16
Mounting Dimensions, Size 45, Series 31 Service Ports at Side and Rear; Non Through Drive
17
H(S)P-10V45 Shaft, Metric Mount, and Port Dimensions
18
Mounting Dimensions, Size 71, Series 31 Service Ports on Side and Rear; Non Through Drive
19
H(S)P-10V71 Shaft, Metric Mount, and Port Dimensions
20
Mounting Dimensions, Size 100, Series 31 Service Ports on Side & Rear; Non Through Drive
21
H(S)P-10V100 Shaft, Metric Mount, and Port Dimensions
22
Mounting Dimensions, Size 140, Series 31 Service Ports on Side; Non Through Drive, Models 62N00 and 12N00
23
Through Drive Overview of Through Drive Mounting Options - Dimensions
24
Shaft Torque Data 24
Pump Installation Notes 28
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Features Axial piston pump H(S)P-10V in swashplate design is used for hydrostatic transmissions in open loop circuits. Flow is proportional to drive speed and displacement. By adjusting the position of the swashplate it is possible to smoothly vary
Swash plate
Cylinder block
Variable piston
Piston
Housing
Valve plate
DFR control valve
End cover
Shaft
Returning piston
• • • • • •
Flange connections to SAE-UNC or Isometric 2 case drain ports High permissible speeds Good suction characteristics Low noise level High power/weight ratio
• • • • •
1
Long service life Quick response time Axial and radial loading of drive shaft possible Wide range of controls Through drive option for multi-circuit system
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Technical Data 1. Input operating pressure range Absolute pressure at port S (A) P min........................................0.8bar (12 psi) P
abs
max.......................................30bar (435 psi)
abs
2. Output operating pressure range Pressure at port B Nominal pressure PN....................280bar (4000 psi) Peak pressure Pmax...............350bar (5100 psi) Pressure data to DIN24312 3. Case drain pressure psi ( 0.5 bar ) higher than input pressure at port S, but not higher than 30 psi ( 2 bar ) absolute.
5. Table of values (theoretical values, without considering Size cm3/rev
η mh and η v
; values rounded)
18
28
45
71
100
140
18 (1.10)
28 (1.71)
45 (2.75)
71 (4.33)
100 (6.1)
140 (8.54)
3300
3000
2600
2200
2000
1800
59.4 (15.7)
84 (22)
117 (31)
156 (41)
200 (53)
252 (67)
28 (36.6)
39 (51)
55 (72)
73 (96)
93 (124)
118 (156)
Displacement
Vg max
cm /rev (in /rev)
Max. Speed
No max
rpm
Max. Flow
Oo max
L / min (gpm)
Max. Power
Po max
kW (HP)
Max. Torque @Vg max, No max
Tmax
Nm (ft - lb)
80 (58)
125 (91)
200 (146)
316 (230)w
445 (324)
623 (453)
Kg (lbs)
12 (27)
15 (33)
21 (46)
33 (73)
45 (99)
60 (132)
3
3
reduced or if the inlet pressure is increased the speed may be increased.
6. Determination of size Flow
qv =
Torque T =
Power
P=
V g • n • ηv 231 Vg • Δ p 24 • π • ηmh qv • Δ p 1714 • ηt
[gpm]
[lb-ft]
[HP]
( ( (
qv =
T=
P=
V g • n • ηv
Vg • Δ p 20 • π • ηmh qv • Δ p 600 • ηt
) ) )
[L/min]
1000
[Nm]
[kW]
2
V g = Displacement per revolution in in3 (cm 3 ) Δ n ηv ηmh ηt
= Speed in rpm (min –1 )
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Ordering Code H(S)P-10V
Axial Piston Unit
O
Swash plate variable pump
HP-10V
Swash plate variable pump for industrial
HSP-10V
71
DR
/
31
R
-
P
S
Mode of Operation Pump, open circuit
O
Size Displacement Vgmax
cm3//rev (in3//rev)
18 (1.10)
28 (1.71)
45 (2.75)
71 (4.33)
100 (6.10)
140 (8.54)
DR DRG
DFR DFR1
DFLR
Control Devices Pressure control Pressure remote control w/ X port blocked)
Pressure,Flow & Power control
Series Series
31
Direction of Rotation Viewed from shaft end
clockwise
R
counter-clockwise
L
Seals Buna-N (NBR per DIN IS0 1629) ;
P V
18
28
45
71
100
140
SAE- splined shaft, reinforced (U-type shaft)
-
W
SAE- keyed shaft
K
Parallel with key DIN 6885
P
Shaft End SAE-splined shaft SAE-splined shaft, reinforced (higher thru drive torque) SAE splined shaft, smaller size (not for pumps with thru drive)
3
S R U
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Ordering Code C
62
N00 Through drives
18
Without through drive (Non-Thru Drive)
28
45
71 100 140
N00
O -
-
-
-
-
K401)
With through drive to accept an axial piston pump or a gear pump hub
sealing to mount
82-2 (A)
3/4” keyed (A-B)
axial
H(S)P-10V18 (K)
101-2 (B)
7/8” keyed (B)
axial
H(S)P-10V28 (K)
101-2 (B-B)
1” keyed (B-B)
axial
H(S)P-10V45 (K)
127-2 (C)
1-1/4” keyed (C)
axial
H(S)P-10V71 (K)
127-2 (C)
1-1/2” keyed (C)
radial H(S)P-10V100 (K)
152-4 (D)
1-3/4” keyed (D)
axial
H(S)P-10V140 (K)
82-2 (A)
5/8” 9T (A)
axial
H(S)P-10V18(U)
82-2 (A)
3/4” 11T (A-B)
axial
H(S)P-10V18(S,R), 10(S)
101-2 (B)
7/8” 13T (B)
axial
H(S)P-10V28(S,R), 45(U,W)
101-2 (B)
1” 15T ( B - B )
axial
H(S)P-10V45(S,R), 60(U,W)
127-2 (C)
1-1/4” 14T (C)
axial
127-2 (C)
1-1/2” 17T (C-C) axial
H(S)P-10V100(S,R), 85(S)
152-4 (D)
1-3/4” 13T (D)
H(S)P-10V140(S,R)
1)
axial
H(S)P-10V71(S,R), 100 (U,W)
K081) K381) K211) K01 K52 K68/K02 K04 K07/K15 K24 K17
See Thru Drives section for other options
(Pressure port B and Suction port S)
18
28
45
71
100
140
61
-
-
-
-
91
-
Rear ports, UNC mounting screws Opposite side ports, UNC mounting screws Rear ports, metric mounting screws Opposite side ports, metric mounting screws Rear ports, UNC mounting screws Opposite side ports, UNC mounting screws Rear ports, metric mounting screws
-
Opposite side ports, metric mounting screws
Mounting Flange
18
28
45
71
100
140
SAE 2 hole
-
-
-
-
-
SAE 4 hole
K051)
Permitted with reduced thru drive torque
Service Ports
ISO 2 hole
K031)
4
-
62 11 12
92
Ports 61, 11, 91 & 41 nonthrough drive only
41 42
C A D
= available O = in preparation - = not available
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Fluid 1. Fluid: AW68 (Q / TCNK 12-2001) 2. Operating viscosity range V opt = 16 mm2 / s ~ 36 mm2 / s (80-170 sus) selected in the range: V opt = opt. operating viscosity 16 ~ 36 mm2 / s Referred to tank temperature (open loop circuit). Limits of viscosity range (The following values are valid for extreme operating conditions): V min = 10 mm2 / s (60 sus) For short periods (t ≤ 1 minute) at max. leakage oil temperature of 800C (176 0F) V max = 1000 mm2 / s For short periods upon cold start 3. Temperature range T min = -200C (-130F) : T max = +800C (+1760F) 4. Filtration I class of at least 16 / 19 to IS04406.
Installation Notes engine transmission shaft and pump shaft must be less than
0.05mm (0.002 in).
5
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Noise Level
Characteristics for pump Measured in an sound chamber Distance from microphone to pump = 3.3 ft (1m) Measuring error: + 2 dB(A) Fluid: Hydraulic oil to ISO VG 46 DIN 51519, t=122˚ F(50˚C)
*Sound data representative of piston pumps of this design.
6
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 DR Pressure Control The pressure control serves to maintain a constant pressure in the hydraulic system within the control range of the pump. The pump therefore supplies only the amount of hydraulic set at the pilot valve.
Static characteristic ( at n1 = 1450rpm ; toil = 500C) 1220F P
(Flow)
Hysteresis and pressure increase
Setting range
Ports
20
280
B
Pressure port
(290 psi)
(4000 psi)
S
Suction port
L, L1
Case drain ports (L1 sealed)
Operating pressure p[bar]
Control Data Hysteresis and repetitive accuracy Size Bar (psi)
...................... max. 3 bar (45 psi) 18
28
45
71
100
140
4 (58)
4 (58)
6 (87)
8 (116)
10 (145)
12 (174)
Pilot oil consumption...............................max. approx. 3 L/min (0.8 gpm)
7
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Unit Dimensions DR Service Ports at Rear; Models 61N00 and 11N00 Sizes 18 to 140 Mounting of pilot valve for clockwise Mounting ofrotation pilot direction of valve for clockwise direction of rotation
Mounting of pilot valve for anticlockwise Mounting ofrotation pilot direction of valve for anticlockwise direction of rotation
Unit Dimensions DR Service Ports on Side; Models 62N00 and 12N00 Sizes 18 to 140
Mounting of pilot valve for anticlockwise Mounting ofrotation pilot direction of valve for anticlockwise direction of rotation
Mounting of pilot valve for clockwise Mounting ofrotation pilot direction of valve for clockwise direction of rotation
Sizes Sizes
A1 mm (in)
A2 mm (in)
A3 mm (in)
A4 mm (in)
18
110mm (4.33”) A1 (in)
- (in) A2 mm
105mm (4.13”) A3 (in)
126mm (4.96”) A4 (in)
28 18
108.5 (4.27”) 110 (4.33”)
226.2 -(8.91”)
108.5 (4.27”) 105 (4.13”)
136 126 (5.35”) (4.96”)
45 28
108.5 (4.27”)
245 (9.65”) 226.2 (8.91”)
108.5 (4.27”)
146 (5.35”) (5.75”) 136
71 45
106 (4.17”) 108.5 (4.27”)
279 245(10.98”) (9.65”)
108.5 (4.27”)
160(5.75”) (6.3”) 146
100 71
108.5 (4.27”) 106 (4.17”)
344 (10.98”) (13.54”) 279
108.5 (4.27”)
158 160(6.22”) (6.3”)
140 100
126 (4.964”) 108.5 (4.27”)
344 (13.54”)
127 (5.0”) 108.5 (4.27”)
169 (6.22”) (6.65”) 158
140
126 (4.964”)
-
127 (5.0”)
169 (6.65”)
8
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 DRG Pressure Control, Remote Control Function and design for DRG. Customer Supplied
A pressure relief valve may be externally piped to port X for remote control purposes. It is not, however, included with DRG control. The differential pressure at the pilot valve is set as standard to 20 If another setting is required (in the range 10-22 bar), please state this in clear text.
Static Characteristic ( at n1 = 1450rpm ; toil = 500C) 1220F Hysteresis and pressure increase
P
(Flow)
Ports B
Pressure port
S
Suction port
L, L1
Case drain ports (L1 sealed)
X
Pilot pressure port
Setting range 20
(290 PSI)
280
(4,000 PSI)
Operating pressure p [bar]
Control Data Hysteresis and repetitive accuracy p...........max 3 bar (45 psi) Max. pressure increases Size Bar (psi)
18
28
45
71
100
140
4 (58)
4 (58)
6 (87)
8 (116)
10 (145)
12 (174)
Pilot oil consumption...............................................max. approx. 4.5 L/min(1.19gpm)
9
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 DFR/DFR1 Pressure/Flow Control In addition to the pressure control function, the In addition to the function, the may be varied bypressure means ofcontrol a differential pressure at the may be varied by means of a differential pressure at the Customer Customer Supplied Supplied
With DFR1 With DFR1 plugged plugged
Static Characteristic Static ( at n1Characteristic = 1450rpm ; toil = 5000C) 12200F ( at n1 = 1450rpm ; toil = 50 C) 122 F P P
(Flow) (Flow)
Hysteresis and pressure increase Hysteresis and pressure increase
Ports Ports
Setting range range Setting 20 20
280 280
(290 psi)
B B S S
Pressure port port Pressure Suction port port Suction
L, L1 L1 L, X
Case drain drain ports ports (L1 (L1 sealed) sealed) Case Pilot pressure port
(4,000 psi)
Operating pressure p[bar]
Flow Control/Differential Pressure
Static characteristic at variable speed
When When port port X X is is unloaded unloaded to to tank, tank, a a zero zero stroke stroke pressure pressure (“stand (“stand by”) by”) of of pp = = 18 18 +/+/- 2 2 bar bar (260 (260 +/+/- 30 30 psi) psi) results. results.
(Flow) (Flow)
Standard setting: 14 bar (203psi). If a different setting is required, required, please please state state in in clear clear text. text.
Control Data For pressure control technical data see DR Pressure control For pressure control technical data see DR Pressure control speed n = 1450 rpm speed n = 1450 rpm Size 18 28 45 71 Size 18 28 45 71 0.9 (0.24) 1.0 (0.26) 1.8 (0.48) 2.8 (0.74) Qmax (gpm) L/min 0.9 (0.24) 1.0 (0.26) 1.8 (0.48) 2.8 (0.74) Qmax (gpm) L/min Pilot oil consumption DFR...........................max. approx. 3-4, 5 L/min (0.70-1.19 gpm) Pilot oil oil consumption consumption DFR1.........................max. DFR...........................max. approx. approx. 3 3-4, 5 L/min gpm) Pilot L/min (0.70(0.70-1.19 gpm) Pilot oil consumption DFR1.........................max. approx. 3 L/min (0.70 gpm)
10
(Speed)n (Speed)n
100 100 4.0 (1.06) 4.0 (1.06)
140 140 6.0 (1.6) 6.0 (1.6)
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Unit Dimensions DFR / DFR1 / DRG Service Ports at Rear; Models 61N00 and 11N00 Sizes 18 to 140 Mounting of pilot valve for clockwise direction Mountingofofrotation pilot valve for clockwise direction of rotation
Mounting of pilot valve for anticlockwise direction Mountingofofrotation pilot valve for anticlockwise direction of rotation
Mounting of pilot valve for clockwise direction of rotation
Mounting of pilot valve for anticlockwise direction of rotation
Unit Dimensions DFR / DFR1 / DRG Service Ports on Side; Models 62N00 and 12N00 Sizes 18 to 140
Mounting of pilot valve for anticlockwise direction Mountingofofrotation pilot valve for anticlockwise Mountingofofrotation pilot direction valve for anticlockwise direction of rotation
Mounting of pilot valve for clockwise direction Mountingofofrotation pilot Mounting valve of forpilot clockwise valve for clockwise direction of rotation direction of rotation
Sizes mm (in) Sizes 18 mm (in) 28 18 45 28 71 45 100 71 140 100 140
A1 Sizes A1 mm (in)
A2 A1
A2 36(1.42)
A3 A2
A3 -
A4 A3
A4 -
A5 A4
A5 -
A6 A5
A7
A6
A7
A6 -
A7 166(6.54)
18 36(1.42) 73(2.87) 36(1.42) 108.5(4.27) - 43(1.69) - 209.2(8.23) 226.2(8.9) 36(1.42) 28 73(2.87) 36(1.42) 108.5(4.27) 43(1.69) 209.2(8.23) 226.2(8.9) 82 (3.21) 36(1.42) 108.5(4.27) 40(1.57) 229(8.98) 245(9.65) 73(2.87) 36(1.42)36(1.42) 108.5(4.27) 43(1.69) 209.2(8.23) 45 82 (3.21) 108.5(4.27) 40(1.57) 229(8.98) 226.2(8.9) 245(9.65) 91 (3.60) 36(1.42) 106(4.17) 42(1.65) 262(10.31) 279(10.98) 82 71 (3.21) 91 (3.60) 36(1.42)36(1.42) 108.5(4.27) 229(8.98) 106(4.17)40(1.57) 42(1.65) 262(10.31) 245(9.65) 279(10.98) 96.3 (3.79) 36(1.42) 108.5(4.27) 40(1.57) 327(12.87) 344(13.54) 100 96.3 (3.79) 36(1.42) 108.5(4.27) 40(1.57) 327(12.87) 344(13.54) 91 (3.60) 36(1.42) 106(4.17) 42(1.65) 262(10.31) 279(10.98) 140 (5.51) 36(1.42) 27(1.06) 353(13.9) 379(14.92) 140(3.79) 140 (5.51) 27(1.06) 353(13.9) 344(13.54) 379(14.92) 96.3 36(1.42)36(1.42) 108.5(4.27)- 40(1.57) 327(12.87)
140 (5.51)
36(1.42)
-
27(1.06)
353(13.9)
379(14.92)
11
166(6.54) 176(6.9) 166(6.54) 176(6.9) 191(7.5) 176(6.9) 191(7.5) 219(8.6) 191(7.5) 219(8.6) 287(11.3) 287(11.3) 219(8.6) 258(10.16) 258(10.16) 287(11.3)
258(10.16)
A8 A8
A8 105(4.13)
A9 A9
A9 40(1.57)
A10 A10
A10 109(4.29)
A11 A11
A11 126(4.96)
X X
X 7/16-20UNF-2B
105(4.13) 126(4.96) 7/16-20UNF-2B 108.5(4.27) 40(1.57) 40(1.57)109(4.29) 119(4.69) 136(5.35) 7/16-20UNF-2B
105(4.13)
40(1.57)
109(4.29)
126(4.96)
7/16-20UNF-2B
108.5(4.27) 136(5.35) 7/16-20UNF-2B 108.5(4.27) 40(1.57) 40(1.57)119(4.69) 129(5.08) 146(5.75) 7/16-20UNF-2B
108.5(4.27)40(1.57) 40(1.57) 119(4.69) 136(5.35) 7/16-20UNF-2B 108.5(4.27) 129(5.08) 146(5.75) 7/16-20UNF-2B 108.5(4.27)
40(1.57)
143(5.63)
160(6.30)
7/16-20UNF-2B
108.5(4.27)
40(1.57)
141(5.55)
158(6.22)
7/16-20UNF-2B
127(5.0)
27(1.06)
183(7.2)
209(8.23)
9/16-18UNF-2B
127(5.0)
27(1.06)
183(7.2)
209(8.23)
9/16-18UNF-2B
108.5(4.27)40(1.57) 40(1.57) 129(5.08) 146(5.75) 7/16-20UNF-2B 108.5(4.27) 143(5.63) 160(6.30) 7/16-20UNF-2B 108.5(4.27) 141(5.55) 158(6.22) 7/16-20UNF-2B 108.5(4.27)40(1.57) 40(1.57) 143(5.63) 160(6.30) 7/16-20UNF-2B 127(5.0) 183(7.2) 209(8.23) 9/16-18UNF-2B 108.5(4.27)27(1.06) 40(1.57) 141(5.55) 158(6.22) 7/16-20UNF-2B
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 DFLR Pressure / Flow / Power Control In achieve aa constant constant drive drive torque torquewith withaavarying varying In order order to to achieve operating pressure, the the swivel swivel angle angle and andwith withititthe theoutput output operating pressure,
Flow is possible possible below below the the limit limitof ofthe thepower powercurve. curve. Flow control control is
Customertoto Customer Supply Supply Maximumpower powercurve curve Maximum 100
(Flow) (Flow)
75
50 25 25
Minimum power Minimum power curve curve
05 05
0 0
100 100 150 150 200 200 250 250 300 300
Ports Ports BB
Operating Operating pressure pressure p[bar] p[bar]
SS L,L, L1 L1 XX
Pressure Pressureport port Suction port Suction port Case (L1 sealed) Casedrain drainports ports (L1 sealed) Pilot pressure port Pilot pressure port
The power power characteristic (5HP, 1800RPM). The characteristic is is factory factory -- set, set,so soplease pleaseenter enterdetails detailsininclear cleartext, text,e.g. e.g.20kW 20kWatat1450 1450rpm rpm (5HP, 1800RPM).
Control Data For pressure control technical data see DR Pressure control. For pressure control technical data see DR Pressure control. Start of control.............................................from 80 bar (1,160 psi) Start of control.............................................from 80 bar (1,160 psi)(1.45 gpm) Pilot oil consumption....................................max. approx. 5.5 L/min Pilot oil consumption....................................max. approx. 5.5 L/min (1.45 gpm)
12
hydraut.com
Variable Displacement Pump H(S)P-10V Series 31 Unit Dimensions DFLR Service Ports at Rear; Models 61N00 and 11N00 Sizes 18 to 140 Mounting of pilot Mounting of pilot valve valve for clockwise for clockwise direction of rotation direction of rotation
Mounting of pilot Mounting of pilot valve valve for anticlockwise for anticlockwise direction of rotation direction of rotation
Mounting of pilot valve for clockwise direction of rotation
Mounting of pilot valve for anticlockwise direction of rotation
PowerPower valve valve
Power valve
Unit Dimensions DFLR Service Ports on Side; Models 62N00 and 12N00 Sizes 18 to 140
Mounting of pilot Mounting of pilot Mounting of pilot Mounting of pilot valve valve for anticlockwise for anticlockwise valve valve for clockwise for clockwise Mounting of rotation pilot direction of rotation direction of Mounting of pilot direction of rotation direction of rotation
PowerPower valve valve Power valve
Sizes Sizes A1 mm(in) mm(in)
Sizes
A1
28
120(4.72)
45
129(5.08)
A2 A1mm(in)
A2 A3
A2
A3
A4
87.5(3.44)
47(1.9)
108.5(4.27)
48(1.89)
226.2(8.9)
43(1.69)
108.5(4.27)
92.8(3.65)
47(1.9)
112.5(4.43)
55(2.17)
245(9.65)
40(1.57)
108.5(4.27)
A4 A3
A4 A5
A5
valve for anticlockwise direction of rotation
A5 A6
A6
A6 A7
A7
A7 A8
A8
A8 A9
A9
valve for clockwise direction of rotation
A10
A11
A12
140(5.51)
36(1.42)
108.5(4.27)
40(1.57)
119(4.69)
136(5.35)
7/16-20UNF-2B x 0.39H
155(6.10)
36(1.42)
108.5(4.27)
40(1.57)
129(5.08)
146(5.75)
7/16-20UNF-2B x 0.39H
A9 A10
A10A11
A11 A12
A13
A12A13
A14
A13A14
X
A14X
X
28
87.5(3.44)87.5(3.44) 47(1.9) 28120(4.72) 120(4.72)
45
92.8(3.65)92.8(3.65) 47(1.9) 47(1.9) 112.5(4.43)112.5(4.43) 55(2.17) 55(2.17) 245(9.65) 245(9.65) 40(1.57) 40(1.57) 108.5(4.27)108.5(4.27) 155(6.10) 155(6.10) 36(1.42) 36(1.42) 108.5(4.27)108.5(4.27) 40(1.57) 40(1.57) 129(5.08) 129(5.08) 146(5.75) 146(5.75) 7/16-20UNF-2B x 0.39H x 0.39H 45129(5.08) 129(5.08) 7/16-20UNF-2B 71 139(5.47) 103.5(4.07) 47(1.9) 124(4.88) 69(2.72) 279(10.98) 42(1.65) 106(4.17) 218.8(8.61) 36(1.42) 108.5(4.27) 40(1.57) 143(5.63) 160(6.30) 7/16-20UNF-2B x 0.39H
108.5(4.27)108.5(4.27) 48(1.89) 48(1.89) 226.2(8.9)226.2(8.9) 43(1.69) 43(1.69) 108.5(4.27)108.5(4.27) 140(5.51) 140(5.51) 36(1.42) 36(1.42) 108.5(4.27)108.5(4.27) 40(1.57) 40(1.57) 119(4.69) 119(4.69) 136(5.35) 136(5.35) 7/16-20UNF-2B x 0.39H x 0.39H 47(1.9) 7/16-20UNF-2B
71
103.5(4.07) 47(1.9)112.6(4.43) 124(4.88) 69(2.72) 279(10.98) 42(1.65) 42(1.65) 106(4.17) 106(4.17) 218.8(8.61)218.8(8.61) 36(1.42)36(1.42) 108.5(4.27) 40(1.57) 143(5.63) 160(6.30) 7/16-20UNF-2B 71139(5.47) 139(5.47) 103.5(4.07) 47(1.9) 124(4.88) 36(1.42) 108.5(4.27) 40(1.57) 143(5.63) 100 145(5.71) 47(1.9) 132.5(5.22)69(2.72) 110.8(4.36)279(10.98) 344(13.54) 40(1.57) 108.5(4.27) 250(9.84) 108.5(4.27) 40(1.57) 148(5.83) 165(6.50)160(6.30) M14 x7/16-20UNF-2B 1.5-6Hx 0.39H x 0.39H
100
112.6(4.43) 47(1.9)140(5.51) 132.5(5.22)132.5(5.22) 344(13.54) 40(1.57) 40(1.57) 108.5(4.27)108.5(4.27) 250(9.84) 250(9.84) 40(1.57) 148(5.83) 165(6.50) M14 x 1.5-6H 100145(5.71) 145(5.71) 112.6(4.43) 47(1.9) 110.8(4.36) 108.5(4.27) 40(1.57) 148(5.83) 140 148(5.83) 140(5.51) 99(3.90) 344(13.54) 379(14.92) 209(8.23) 183(7.2) 127(5.00) 27(1.06) 183(7.29) 209(8.23)165(6.50) 9/16-18UNF-2B xM14 0.51Hx 1.5-6H - 110.8(4.36) - 36(1.42) 36(1.42) - 108.5(4.27)
140
140(5.51) 140(5.51) 140148(5.83) 148(5.83)
140(5.51) 99(3.90) 99(3.90) 379(14.92)379(14.92) 209(8.23) 209(8.23) 183(7.2) 183(7.2) 140(5.51) -
13
-
-
127(5.00) 27(1.06) 27(1.06) 183(7.29) 183(7.29) 209(8.23) 209(8.23) 9/16-18UNF-2B x 0.51H x 0.51H 127(5.00) 9/16-18UNF-2B -
hydraut.com
Mounting Dimensions, Size 18
Series 31
Unit dimensions, Size 18, Series 31 H(S)P-10V18 Service Ports on Side; Non Through Drive, Unit dimensions, 18, Series 31Models 62N00 and 12N00 H(S)P-10VSO 18, Service ports on side,Size Models 62N00 & 12N00 H(S)P-10VSO 18,dimensions, Service ports on side, 62N00 &31 12N00 WithoutUnit Considering Adjustment SizeModels 18, Series
(6 7)
)
(110.4 3
0.10 (2.5)
0.98 (25)
View SV View V
1.03 (26.2)
View V
4
(26 .76)
4 x M10 (0.67)
0.87 (22)
Centering 3)
1/4-20UNC-2B
1/4-20UNC-2B
Ø 3/4 in
0.55 (14) 0.55 0.55 (14) 1.50 (14) (38)
R3.15x6.7 DIN332
Centering 3)
R3.15x6.7 DIN332 Centering 3)
R3.15x6.7 DIN332
0.87 (22)
1.18 (30) 0.87 (22)
0.62 (15.8)
1.18 (30)
0.62 (15.8)
1.50 (38) 1.18 (30)
1.50 (38)
0.94 (23.8)
1.50 (38)
1.50 (38)
1.30 (33) 1.30 (33)
Ø 3/4 in1/4-20UNC-2B
S Splined shaft 3/4 in 11T U Splined shaft 5/8 in 9T R Splined shaft 3/4 in 11T 16/32 DP 2) 16/32 DP 2) 16/32 DP 2) mech. S Splined shaft (A-B) 3/4 in 11T U SAE Splined shaft 5/8(A) in 9T 5/8 in 9T RR Splined 3/4 in in 11T11T S Splined shaft 3/4 in 11T U Splined shaft Splinedshaft shaft 3/4 SAE J744-19-4 J744-16-4 SAE J744-19-4 (A-B) displacement 16/32 DP 2) 2) 2) 16/32 DP 16/32 16/32 DP 2) 16/32 DP 2) mech. 16/32DP DP 2) mech. limiter SAE J744-19-4 (A-B) SAE J744-16-4 (A) SAE displacement SAE J744-16-4 (A) SAEJ744-19-4 J744-19-4(A-B) (A-B) displacement SAE J744-19-4 (A-B) limiter limiter Ø 3/4 in
3/43/4 inin
3/4 in
0.83 (21.1)
) 0.83 (21.1) –0.02
–0.02
)
0.83 (21.1) ) –0.02
DIA 0.7500 (Ø19.05 0.7492
0.10 (2.5) 1.13 (28.6)
DIA 0.7500 (Ø19.05 0.7492
DIA 0.7500 (Ø19.05 0.7492
Centering 3)
S
4 x M10 (0.67) (17) deep 1.03 (26.2)1.03 (26.2) (17) deep
Shaft ends ISO 3019-1 19-1 with K Parallel key K ISO Parallel with key 3019-1 19-1 ISO 3019-1 19-1
1.13 (28.6) 0.10 (2.5)DIN332 R3.15x6.7
S
12N00
W
W
1.13 (28.6) R3.15x6.73) DIN332 Centering
0.87 (22.2)
4 x M10 (0.67) (17) deep 12N00
7.68 (195)
R3.15x6.7 DIN332
4 x M10 (0.67) (17) deep
12N00
7.68 (195) W
Centering 3)
0.79 (20)
(6 7)
64 2. 5.98 (152)
5.71 (145)
0.1884 0.1874 (4.76 +0.025 0.1884 ) Shaft ends 0.1884 0.1874 +0.025 0.1874 (4.76 ) +0.025 K Parallel key ends (4.76 ) with Shaft
View W
2. 64
7.68 (195) 5.71 (145)
Shaft ends Shaft ends
0.79 (20)
1.87 (47.6)
(11 )
0. 0. 43
4.19 (106.4) 5.98 (152) 4.19 (106.4) 4.19 (106.4) 5.98 (152)
L1
Shaft ends
B
0.98 (25) 2.06 (52.4)
1 .69 (43)
BW View
12N00
0.98 (25)
1 .69 (43)
L 1 (145) 5.71
B
4 x M10 (0.67) (17) deep 12N00 0.87 (22.2) 4 x M10 (0.67) View W 12N00 (17) deep 0.87 (22.2)
2.06 (52.4) 2.06 (52.4)
0.45 (11.5)
0.79 (20) 1.87 (47.6)
(11 )
1 82-2L(A)
2.52 (64)
1 .69 (43) 0.45 (11.5)
2.48 (63)
Flange SAE J744 82-2 (A) Flange SAE J744 82-2 (A) SAE J744 Flange
2.48 (63) 2.60 (66)2.48 (63)
2.48 (63)
L
3.2500 DIA 3.2479 (Ø82.55 h)8
0.45 (11.5)
V
2.60 (66) 2.52 (64) 2.522.60 (64)(66)
L
43
V
3.27 (83)
0.25 (6.3)
3.2500 DIA 3.2479 (Ø82.55 h)8
3.2500 DIA 3.2479 (Ø82.55 h)8
0.25 (6.3)
V L
2.48 (63)
3.27 (83)
2.48 (63)
0.25 (6.3)
1.87 (47.6)
H(S)P-10VSO 18, Service ports on side, Models 62N00 & 12N00 3.27 (83)
0.94 (23.8) 0.62 (15.8) 1.25 (31.8) 1.25 (31.8)
1.50 (38)
0.94 (23.8) 1.25 (31.8)
1.61 (41) 1.61 (41) 1.30 (33) 1.61 (41)
Ports Ports Ports
Designation Designation Designation Ports Ports
S L,L1 X X
Port for
Standard usable spline length Standard
usable spline length
usable spline length Standard
Size Size
Peak Tightening Peak Tightening Pressure Torque MaxMax Pressure Torque 2) Tightening torques, max. 2) Size Tightening torques, Peak Tightening max. [psi (bar)] [lb-ft (Nm)]
[psi (bar)]
[lb-ft (Nm)]
Pressure Torque Max PressureThreading port (standard pressure range) SAE range) J518 3/4 in3/8-16 Pressure port (standard pressure J518 UNC-2B; 3/4 in0.79 (20) deep 29 lb-ft (40Tightening in bolt holes ISO 68 SAE Nm) Ports torques, max. 2) Pressure (standard pressure range) J518 3/4 in0.79 UNC-2B; [psi (bar)] [lb-ft (Nm)] Threading in port bolt holes ISO 68 SAE 3/8-16 UNC-2B; (20) deep 0.79 29 lb-ft (40 Nm) 5100 (350) Threading in bolt holes ISO 68 3/8-16 (20) deep 29 (40) S Pressure Inlet port pressure range) SAE J518 13/4 in in 3/8-16 UNC-2B; 0.79 (20) deep B Threading port (standard pressure range) SAE J518 in (standard bolt holes ISO 168 5100 (350) 29 (40) port (standard pressure range) SAE J518 in B SS Inlet Threading Pressure port (standard pressure range) SAE J518 3/4 in Threading in bolt holes ISO 68 3/8-16 UNC-2B; 0.79 (20) deep 29 lb-ft (40 Nm) Inlet (standard pressure range ) 1 in in bolt holes ISO 68 SAE J518 3/8-16 UNC-2B; 0.79 (20) deep 29 lb-ft (40 Nm) Threading in bolt holes ISO 68 3/8-16 0.79 UNC-2B; (20)UNC-2B; deep 0.79 2959 lb-ft Nm) InletThreading (standard pressure range ) SAE J518 1 3/8-15 in 3/8-16 inbolt holes ISO 6868UNC-2B; (20) deep 75 (5)5100 (350) 29 (40)29 (40) in holes ISO 0.79 (20) deep CThreading ase port (Lbolt plugged) ISO 11926 9/16-18 lb-ft(40 (80 Nm) 1 1 S L/LInlet portdrain (standard pressure range) SAE J518 1 in UNF-2B in bolt holes ISO 68 3/8-15 UNC-2B; 0.79 (20) deep 29 (40) ase drain port (L plugged) ISO 11926 9/16-18 UNF-2B 59 lb-ft (80 Nm) 75 (5) L/L 1 CThreading 1) ANSI B92.1a-1976, pressure angle 30 ° 1 Case drain plugged) 11926 9/16-18 UNF-2B 30 (2) 59 (80) Threading in bolt(L holes ISO 68 ISO 3/8-16 (20) deep 29 lb-ft (40 Nm) S L,L1 Inlet (standard SAE J518 UNC-2B; 1 in 0.79 1pressure range ) BB
B
Port for Port for
B
Pressure port (standard pressure range)
SAE J518
3/4 in
2) See safetypressure information ANSI B92.1a-1976, angle 30 ° drain (L plugged) ISO 11926 9/16-18 UNF-2B 30 (2) (5) 59 (80) holes ISO 68 3/8-15 UNC-2B; 0.79 deep CThreading ase drain port (Lbolt plugged) ISO 11926 9/16-18 UNF-2B 59(20) lb-ft (80 Nm) L/LCase 1 in 13) Axial locking 1 X safety Pilot Pressure ISO 11926 7/16-20 UNF-2B; 0.39 (10) deep 5100 75 (350) 29 (40)29 (40) of the coupling e.g. via clamping coupling or radial mounted binding screw See information 1) ANSI B92.1a-1976, pressure angle 30 ° Pilot Pressure ISODIN 11926 7/16-20 UNF-2B; 0.39 (10) deep 1740 510030 (350) (40) L,L3)1Axial Case drain (L plugged) ISO 11926 9/16-18 UNF-2B (2) 4829 of the coupling e.g. via clamping binding screw 1 X 2)locking pressure for DG coupling control or radial mounted 3852 R 1/4 in (120) (70)59 (80) See safetyControl information 3) X Pilotpressure Pressure ISO 7/16-20 UNF-2B; 0.39 (10) deep (350) 29 (40) Axial locking of the coupling clamping coupling or radial binding screw Control fore.g. DGviacontrol DINmounted 385211926 R 1/4 in 17405100 (120) 48 (70) 1) Dependent on the installation position, port L or L 1 must be connected
1)
2)
X
Control pressure for DG control
DIN 3852
1) Dependent on the installation position, port L or L 1 must be connected
1) Dependent on the installation position, port L or L 1 must be connected
14
R 1/4 in
1740 (120)
48 (70)
hydraut.com
Mounting Dimensions, Size 28 Series 31 H(S)P-10V28 Service Ports at Side and Rear; Non Through Drive Without Considering Adjustment Valve Valve mounting mountingfor for counter clockwise counter clockwise rotation
Port Portplate plate62/12 62
V
L
45°
.91
3.54 (90 )
DIA 4.0000 ) 3.9979 (Ø101.6 h8
L
2.87 (7 3) 1.87 (4 7.6) 0.79 B (20) X
3.11 (79)
1.77 (45)
Z
0.55 (14) 1.57 (40)
L1
1.25 (32) 2.31 (58.7)
6.69 (170 ) 8.23 (20 9) 8.90 (226)
rotation
S
2.31 (58.7) 1.26 (32)
1.87 (47.6)
0.79 (20)
View ViewW W
B
S
Valve Valvemounting mountingfor for counter clockwise counter clockwise rotation
View ViewVV
0.87 (22.2)
0.87 (22.2)
W
Port plate 61
1.77 (45)
6.46 (164) 7.64 (194)
Port plate 61/11
0.37 (9.5) 0.25 (6.3)
5.75 (146) 6.46 (164) 3.29 (83.5) 4.68 (119 ) 5.35 (13 6)
S
L1
4) (7
2
1.69 (43) max. 4.45 (113)
0.55 (14) 1.57 (40)
X
0. DI A
3.15 (80)
45°
3.15 (80)
DIA 4.0000 ) 3.9979 (Ø101.6 h8
6.8 (Ø 5 17 4)
1.19 (30.2)
11/12N00 threads, M10; 17 deep
15
1.57 (40) max. 4.33 (110) 2.91 (74)
X
55
Flange SAE J744 101-2 (B)
rotation
B
1.19 (30.2)
5.47 (13 9) 3.54 (90 ) L
(14 )
0.25 (6.3) 0.37 (9.5)
hydraut.com
Mounting Dimensions, Size 28 Series 31 H(S)P-10V28 Shaft, Metric Mount, and Port Dimensions Without Considering Adjustment Shaft P, Flange A Z ; View W
RA 92701-A/12.09
View H
| (A)A10V(S)O
Bosch Rexroth
Dimensions, size 28
0.63 (16 ) 0.99 (25. 1) 1.30 (33. 1) 1.61 (41)
1.30 (33. 1) Usuable spline length 1.61 (41)
DIA 7/8 in 1/4-20UNC-2B
0.63 (16 )
Usuable spline length
0.98 (25) 1.61 ( 41)
Standard
Size
3/4 in 3/8-16 UNC-2B; 0.79 (20) deep
Peak press. [psi (bar)]
Service line (standard pressure range) Fixing thread
SAE J518 ISO 68
S
Inlet (standard pressure range ) Fixing thread
SAE J518 ISO 68
L,L1
Case drain (L1 plugged)
ISO 11926
0.63 (16 ) 1 1/4 in 0.99 (25. 1) 7/16-14 UNC-2B; 0.94 (24) deep 75 (5) 1.30 (33. 1) 3/4-16 UNF-2B; 0.47 (12) deep 30 1.61 (41) (2)
X
Pilot pressure
ISO 11926
7/16-20UNC-2B; 0.47 (12) deep
X
Control pressure for DG control
DIN 3852
R 1/4 in
1/4-20UNC-2B
1) Dependent on the installation position, port L or L 1 must be connected O = Must be connected
16
1)
DIA 3/4 in 1/4-20UNC-2B
DIA 3/4 in 1/4-20UNC-2B
1/4-20UNC-2B
DIA 3/4 in
0.55 (14) 0.55 ( 14 ) Usuable spline length Usuable spline length 0.83 ( 21) 1.18 (3 0) 1.50 (3 8) 1.50 (3 8)
DIA 7/8 in 1/4-20UNC-2B
Port for
1)
W Splined Shaft 3/4 in 11T 16/32 DP SAE J744 - 19-4 (A-B)
Ports H(S)P-10V 28
B
0.98 (25)
1)
0.55 (14) 1.18 (3 0) 1.50 (3 8)
Designation
0.63 (16 )
1.61 ( 41)
1/4-20UNC-2B
DIA 3/4 in
U Splined Shaft 3/4 in 11T 16/32 DP SAE J744- 19-4 (A-B)
Drive shafts
K Parallel with key 3019-1 22-1 0.63ISO ) K(16 Parallel with key ISO 3019-1 22-1 0.99 (25. 1)
DIA 7/8 in 1/4-20UNC-2B
DIA 7/8 in 1/4-20UNC-2B
R Splined shaft 7/8 in 13T 16/32 DP
5100 (350)
0.55 ( 14 ) 0.83 ( 21) 1.50 (3 8)
Tightening Torque, Max [lb-ft (Nm)]
State
29 (40)
O
48 (85)
O Usuable spline length
118 (160)
O1)
5100 (350)
29 (40)
O
1740 (120)
48 (70)
O
DIA 7/8 in
1)
DIA 7/8 in 1/4-20UNC-2B
S Splined shaft 7/8 in 13T 16/32 DP SAE J744- 22-4 (B)
hydraut.com
Mounting Dimensions, Size 45 Series 31 H(S)P-10V45 SHAFT, Service Ports at Side and Rear; Non Through Drive Without Considering Adjustment Port Plate 62/12 N00
3.54 (90)
45°
3.17 (80.5)
45°
5.75 (146) 7.24 (184) 3.68 (93.5) 5.08 (129) 5.75 (146) Control Control valve valve mounting mountingfor for counter counter clockwise rotation clockwise rotation
0.56 (14.3) 1.77 (45)
S 1.57 (Ø40) 2.75 (69.9 )
7.44 (18 9) 9.65 (245)
View ViewV V
1.57 (Ø 4 0 )
2 .7 5 (69.9)
0 .9 8 (Ø25) 2 .0 6 (52.4)
11/12N00 threads M10; 17 deep
Controlvalve valve Control mounting mountingfor forcounter counter clockwise clockwise rotation rotation
View ViewWW
B
1.40 (35.7) 17
B
1.97 (50)
Z
L1
1.03 (26.2)
3.23 (82) 2.06 (52.4) 0.98 (Ø25)
1.97 (50)
X
3.46 (88)
40
X
max. 4.33 (110)
8.98 (228) 3.78 (96 ) L
View Z
1.03 (26.2)
W
1.40 (35.7)
7.24 (184) 8.62 ( 219 )
DIA 4.0000 3.9979 (Ø101.6
h8)
L
3.54 (90) L1
Port Plate 61/11 N00
Flange SAE J744 101-2 (B)
55
0.
X
(8 27 3.
X
h8)
0.56 (14.3) 1.77 (45)
0.37 (9.5) 0.25 (6.3)
) 14 Ø (
1.57 (40) max. 4.33 (110)
3)
V 6.06 (154) 3.78 (96 ) L
DIA 4.0000 3.9979 (Ø101.6
Flange SAE J744 101-2 (B)
0.37 (9.5) 0.25 (6.3)
S
11/12N00 threads M12; 20 deep
hydraut.com
Mounting Dimensions, Size 45 Series 31 DIA1 in 1/
DIA 1in 1/
H(S)P-10V45 SHAFT, Metric Mount, and Port Dimensions Drive shafts
0.63 (16 ) 1.18 (3 0) 1.50 (3 8) 1.81 (45.9)
DIA 7/8in 1/4-20UNC-2B
1.18 (3 0) 1.50 (3 8) 1.81 (45.9)
DIA 1in 1/4-20UNC-2B
1)
1)
Usable 1.16 (29.5) spline length
1.81 (45.9)
WSplined shaft 7/8 in 13T 16/32 DP 1) SAE J744 - 22-4 (B ) 0.63 (16 ) 0.63 (16 )
Usable 1.16 (29.5) Usable 1.16 (29.5) spline length 1.81 (45.9) spline length
DIA 7/8in 1/4-20UNC-2B
U Splined shaft 7/8 in 13T 16/32 DP SAE J744 - 22-4 (B) 0.63 (16 )
DIA 1in 1/4-20UNC-2B
DIA1 in 1/4-20UNC-2B
1.50 (3 8) 1.81 (45.9)
1) shaft shaft 1 in 115T 16/32 DP Splined in 15T 16/32(16 DP) R Splined shaft 1 inR15TSplined 16/32R DP 0.63 25-4 (B-B) SAE -J744 - 25-4 (B-B) SAE J744 - 25-4 (B-B) SAE J744
1)
DIA1 in 1/4-20UNC-2B
0.63 (16 ) S Splined shaft 1 in 15T 16/32 DP 1) S Splined shaft 1 in 15T 16/32 DP S Splined shaft 1 in 15T 16/32 DP SAE J744 - 25-4 (B-B) 1.18 (3 0) SAE J744 - 25-4 (B-B) SAE J744 - 25-4 (B-B)
1.81 (45.9)
W Splined shaftshaft 7/8 7/8 in 13T DP U Splined shaft 7/8 in 13T 16/32 DP WSplined in 13T16/32 16/32 DP U Splined shaft 7/8 in 13T 16/32 DP SAE SAE J744 -J744 22-4 (B) U Splined shaft 7/8 in 13T 16/32 DP 1) J744 - 22-4 (B) WSplined shaft 7/8 in 13T 16/32 SAE DP 1) - 22-4 (B ) SAE J744 - 22-4 (B) SAE J744 - 22-4 (B) SAE J744 - 22-4 (B ) 0.63 (16 )
0.63 (16 )
ANSI B92.1a-1976, 30° pressure angle, 0.63 (16 )
0.98 (25. 1) 1.61 ( 41)
0.98 (25. 1) 1)
1)
1.61 ANSI B92.( 141) a-1976, 30° pressure angle,
ANSI B92.1a-1976, 30° pressure angle,
1)
DIA 7/8in 1/4-20UNC-2B
1.61 ( 41)
DIA 7/8in 1/4-20UNC-2B
0.98 (25. 1)
DIA 7/8in 1/4-20UNC-2B
0.63 (16 )
DIA 7/8in 1/4-20UNC-2B
1)
1)
Usable 0.98 (25) spline length 1.61 ( 41)
0.635(16 ) , tolerance class
0.63 (16 ) Usable 0.98 (25) spline length 1.61 ( 41)
Usable 0.98 (25) K Parallel with key spline length 1.61 ( 41) ISO 3019-1 25-1 , tolerance class 5
, tolerance class 5
KK Parallel Parallel with with key key ISO 3019-1 25-1 ISO 3019-1 25-1
K Parallel with key ISO 3019-1 25-1
Shaft P, ISO Flange A 25 mm Ø Shaft
Ports
Ports Ports H(S)P-10V45 Ports
Designation
Port for
Standard
Size
Peak press. [psi (bar)]
Tightening Torque, Max [lb-ft (Nm)]
State
29 (40)
O
66 (90)
O
B
Service line (standard pressure range) Fixing thread
SAE J518 ISO 68
1 in 3/8-16 UNC-2B; 0.71 (17) deep
5100 (350)
S
Inlet (standard pressure range) Fixing thread
SAE J518 ISO 68
1 1/2 in 1/2-13 UNC-2N; 0.87 (22) deep
75 (5)
L, L1
Case drain
ISO 11926
7/8-14 UNF-2B
30 (2)
177 (240)
O1)
X
Pilot pressure
ISO 11926
7/16-20 UNF-2B; 0.39 (10) deep
5100 (350)
29 (40)
O
X
Control pressure for DG control
DIN 3852
R 1/4 in
1740 (120)
48 (70)
O
1) Dependent on the installation position, port L or L 1 must be connected O = Must be connected
18
hydraut.com
Mounting Dimensions, Size 71 Series 31 H(S)P-10V71 SHAFT, Service Ports on Side and Rear; Non Through Drive Dimensions Dimensions in in inches inches and and (mm). (mm).
Without Considering Adjustment
DFR/ DFR/
t plate 92
Withavailable) port plate 92 With port plate 92 (others
7.20 (18 3) (115 )
V0.50 0.50 (12 (12 .7) .7) 0.24 0.24 (6 (6 )) XFlange Flange SAE SAE J744 J744 127-2 127-2 (C) (C)
L1 L1
7.13 (181) 7.13 (181) 7.13 (181) 8.27 ( 210 ) 8.27 (( 210 210 )) 8.27 8.54 (2 17 ) 8.54 (2 17 ) 4.23 (107.5) 5.63 (143) 4.23 (107.5) 5.63 4.23 (107.5) 5.63 (143) (143) 10 10 ..1 12 2 (257) (257) 6.30 (160 ) 6.30 6.30 (160 (160 )) Valve mounting for Valve mounting for Valve mounting mounting for for Valve counter counter clockwise counter clockwise clockwise counter clockwise W W(F) rotation W rotation rotation rotation View View WW View V V View W View View E View F View W Model 92
Model 92
1.69 (42.9)
B
1.69 1.69 (42.9) (42.9)
2.06 2.06 (52.4) (52.4) 0.98 0.98 (25) (25)
3.06 (77.8) 1.97 (50)
1.03 (26.2)
2.06 (52.4) 0.98 (25)
S B B
SS
View Z
t plate 91
View Z Z View View
8.78 (223) 10.98 (2 79 )
1.57 (40) max. 4.33 (110)
X
5.0000 DIA DIA5.0000 (Ø127 h8 )) h8 4.9975 4.9975 (Ø127
0.50 0.50 (12 (12 .7) .7) 0.24 0.24 (6 (6 )) L Flange Flange SAE SAE J744 J744 127-2 127-2 (C) (C) L
3.62 (92) 1.03(262) 10.31 10.31 (262) (26.2) 0.98 (25) 4.53 (115 ) B 4.53 (115 )
L B
X
LL
Z S
0.71 (18 )) 0.71 (18 2.09 2.09 (5 (5 3) 3)
S L1 L1
1.97 (50) 8.78 8.78 (223) (223)3.06 10.98 79 10.98 (2 (2(77.8) 79 ))
3.62 (92) (92) 3.62 1.03 1.03 0.98 B B 0.98
Z Z
Valve mounting for counter clockwise rotation 19
(26.2) (26.2) (25) (25)
BB
X X
1.69 (42.9) 2.28 (58)
10.31 (262) (115 )
XX 2.06 (52.4) 1.57(40) (40) 1.57 2.28 (58) max. max.4.33 4.33 (110) (110)
With With With port port plate plate 91 91
2.06 2.06 (52.4) (52.4) 2.28 2.28 (58) (58)
View V View V
SS
SS
1.97 1.97 (50) (50) 3.06 3.06 (77.8) (77.8)
1.69 1.69(42.9) (42.9) 2.28 2.28 (58) (58)
W
3.06 3.06(77.8) (77.8) 1.97 1.97 (50) (50)
8.54 (2 17 ) 10 .12 (257)
L1
1.57 1.57(40) (40) 3.62 3.62(92) (92) max. max.4.33 4.33(110) (110)
))
4.09 4.09(104) (104)
0.71 (18 )) 0.71 (18 2.09 (5 2.09 (5 3) 3)
4455° °
4455°°
XX
0. A
4.09 4.09(104) (104) X
45°
45°LL
1.57 (40) DDIAIA 00. . 4.33 (110) 3.62 (92) max. 7711 33 (1(188 .8.866 )) (9(988
)
8
3 (18 .86 ) (9
71
X X
1.03 1.03 (26.2) (26.2)
L1
V V
4.09 (104)
5.0000 DIA DIA5.0000 (Ø127 h8 )) h8 4.9975 4.9975 (Ø127
L
V(E)
7.20 7.20 (18 (18 3) 3) 4.53 (115 (115 )) 4.53 LL
DI
L
4.09 (104)
With port plate 92
Valve mounting for Valve Valve mounting mounting for counter clockwise counter counterclockwise clockwise rotation rotation rotation
hydraut.com
Mounting Dimensions, Size 71
Series 31
H(S)P-10V71 SHAFT, Metric Mount, and Port Dimensions
W Splined1.50 shaft (3 1 in8)15T 16/32 DP ) (B-B) 2) SAE0.63 J744-(16 25-4
0.63 (16 )
1.18 (3 0)
1.50 (3 8)
Shaft P, ISO Flange A (45.9) 1.18 (3 0)Ø1.81 32 mm Shaft
Usable spline length
1.81 (45.9) 0.63 (16 )
1.81 (45.9) 1.18 (3 0)
Usable spline length
1.50 (3 8) 1.81 (45.9)
5/16-18UNC-2B
DIA 1 1/4in
1/4-20UNC-2B
5/16-18UNC-2B
DIA 1 1/4in
0.75 (19 ) (3 8) Usable 1.50 1.50 (3 8) spline length 0.63 (161.81 ) (45.9) 2. 18 (55.4)
1.18 (3 0)
1.81 (45.9)
DIA 1 in 1/4-20UNC-2B
DIA 1 in
1/4-20UNC-2B
1.50 (3 8)
Shaft P, ISO Flange A 1.81 (45.9) 0.63 Ø (16 ) 32 mm Shaft
2.18 (55.4)
1.18 (3 0)
1.18 (3 0)
1.18 (3 0)
1.50 (3 8)
0.63 (16 )
1.50 (3 8)
0.63 (16 )
0.75 (19 )
Usable spline length
DIA 1 in 1/4-20UNC-2B
DIA 1 in
2.18 (55.4)
1/4-20UNC-2B DIA 1 in
1.50 (3 8)
1/4-20UNC-2B
2.18 (55.4) W Splined0.75 shaft (191) in 15T 16/32 DP ) (B-B) 2) SAE0.63 J744-(16 25-4 Usable 1.50 (3 8) spline length 1.18 (3 0) 2.18 (55.4)
0.75 (19 ) 1.56 (39.5) 1.87 (47.5) 2.18 (55.4)
0.75 (19 )
1.50 (3 8)
DIA 1 in 1/4-20UNC-2B DIA 1 in
1.50 (3 8)
5/16-18UNC-2B
5/16-18UNC-2B DIA 1 1/4in
DIA 1 1/4in
Usable spline length
U Splined shaft 1 in 15T 16/32 DP SAE J744- 25-4 (B-B) 2)
0.75 (19 ) 1.56 (39.5) 1.87 (47.5) 2.18 (55.4) 2.18 (55.4) 0.75 (19 )
Usable spline length
0.75 (19 )
Usable spline length
2.18 (55.4)
R Splined shaft 1 1/4 in 14T 12/24 DP SAE J744- 32-4 (C) 2)
0.75 (19 ) 1.56 (39.5) 1.87 (47.5) 2.18 (55.4) 0.75 (19 ) 1.56 (39.5) 1.87 (47.5) 2.18 (55.4)
2.18 (55.4)
U Splined shaft 1 in 15T 16/32 DP SAE J744- 25-4 (B-B) 2)
1/4-20UNC-2B DIA 1 in
S Splined shaft 1 1/4 in 14T 12/24 DP SAE J744- 32-4 (C) 2)
R Splined shaft 1 1/4 in 14T 12/24 DP SAE J744- 32-4 (C) 2) DIA 1 1/4in 5/16-18UNC-2B DIA 1 1/4in 5/16-18UNC-2B
DIA 1 in DIA 1 in DIA 1 1/4in DIA 1 1/4in DIA 1 in DIA 1 1/4in 5/16-18UNC-2B 1/4-20UNC-2B DIA 1 in DIA 1 1/4in 5/16-18UNC-2B 1/4-20UNC-2B 1/4-20UNC-2B 5/16-18UNC-2B 1/4-20UNC-2B 5/16-18UNC-2B
S Splined shaft 1 1/4 in 14T 12/24 DP SAE J744- 32-4 (C) 2)
0.63 (16 )
Usable spline length
1.18 (3 0) 1.81 (45.9)
0.63 (16 )
with key Usable K Parallel 1.18 (3 0) spline length ISO 3019-1 32-1 1.81 (45.9)
K Parallel with key ISO 3019-1 32-1
1.81 (45.9)
0.63 (16 )
Usable spline length Usable spline length
1.18 (3 0)
1.81(16 (45.9) 0.63 ) 1.18 (3 0) 1.81 (45.9)
Ports H(S)P-10V71 Designation
Ports H(S)P-10V71 Designation
Port for Port for
Standard Standard
B
Size Size
Peak press. Max State [psi (bar)] Tightening Torque Peak press. Max State [lb-ft (Nm)] [psi (bar)] Tightening
Service line (standard pressure range) SAE J518 1 in Torque Fixing thread ISO 68 3/8-16 UNC-2B; 0.71 (18) deep 5100 (350) 29 (40) [lb-ft (Nm)] BS Service line (standard pressure range) SAE J518 O Intlet (standard pressure range) SAE J5181 in 2 in Fixing ISOISO 68 68 3/8-16 UNC-2B; 0.71 0.87 (18) deep 5100 (350) Fixingthread thread 1/2-13 UNC-2B; (22) deep 75 (5)29 (40)66 (90) SL, L Intlet (standard SAE J518 2 in 7/8-14 UNF-2B Case drain pressure range) ISO 11926 30 (2) 177 (240)O 1 Fixing thread ISO 68 1/2-13 UNC-2B; 0.87 (22) deep 75 (5) 66 (90) X Pilot pressure ISO 11926 7/8-14 UNF-2B; 0.39 (10) deep 5100 (350) 29 (40) 1) Case drain ISO 11926 7/8-14 UNF-2B 30 (2) 177 (240) O L, L1 X Control pressure for DG control DIN 3852 R 1/4 in 1740 (120) 48 (70) X Pilot pressure ISO 11926 7/8-14 UNF-2B; 0.39 (10) deep 5100 (350) 29 (40) O X Dependent onControl pressure for DG port control 3852 R 1/4 in 1740 (120) 48 (70) O 1) the installation position, L or L 1 must DIN be connected
O = Must be connected 1) Dependent on the installation position, port L or L 1 must be connected O = Must be connected
20
O
O O1) O
O
hydraut.com
Mounting Dimensions, Size 100
Series 31
H(S)P-10V100 SHAFT, Service Ports on Side & Rear; Non Through Drive Without Considering Adjustment Port Plate 62/12 NOO
10.83 (2 75 ) 12.48 (3 17 ) L1 3.74 (95 ) 10.83 (2 75 ) W 12.48 (3 17 )
0.79 (20)
Valve mounting for counter clockwise rotation View V
11/12N00 threads M14; 19 deep
1.26 (32) 2.63 (66.7)
B
1.25 (3 1.8) B
View 1.25 Z(3 1.8)
6.89 (175 ) 0.24 (6 )
Z
X
0.79 (20) 3.74 (95 )
0.79 (20)
L1
11.34 (28 8) 12.87 (327) 13.54 L1 (344) 3.74 (95 ) 11.34 (28 8) 12.87 (327) 13.54 (344)
Z
X
X
View W S 2.00 (50.8) S
11/12N00 threads M14; 19 deep
3.90 (99 ) 2.63 (66 .7) View Z Z View 1.26 (32) B 3.90 (99 ) 2.63 (66 .7) 1.26 (32) B
X
L
X
DIA 5.0000 4.9975 (Ø127 h8) DIA 5.0000 4.9975 (Ø127 h8)
0.50 (12 .7)
L
1.57 (40) 1.57 (40) max. 4.33 (110) max. 4.33 (110)
Port plate 61
Flange SAE J744 127-2 (SAE C)
X
)
7.13 (181) 8.27 ( 210 ) 4.65 (118 ) 5.84 (148.4) 6.50 (16 5) Valve Valvemounting mounting for for counter counter7.13 (181) clockwise rotation 8.27 ( 210 ) clockwise rotation 4.65 (118 ) 5.84 (148.4) View View View 6.50 (16 5) WW ViewV V
W
0.50 (12 .7)Port plate 6.89 61 (175 ) 0.24 (6 Flange SAE J744 Port Plate 61/11 NOO) 127-2 (SAE C)
1.57 (40) 1.57(95) (40) max. 4.33 (110) 3.74 3.74 (95) max. 4.33 (110)
) (10 6
L1
2.00 (50.8)
1.25 (31.8) 2.00 (50.8) 2.00 (50.8) 2.16 (55) 1.25 2.16(31.8) (55) 2.16 (55) 2.16 (55)
3.74 (95 )
45°
3.50 (88.9) 3.50 (88.9) 2.36 (60) 2.36 (60)
0.79 (20)
(10 6
Flange SAE J744 127-2 (SAE C)
45°
4.1 7
V X
1.26 (32) 2.63 (66.7)
9.84 (250) 6.89 (175 )
0.24 (6 )
4.1 7
X
5.98 (152) 5.98 (152)0.69 (17.5) 0.69 (17.5)
DIA 5.0000 4.9975 (Ø127 h8) DIA 5.0000 4.9975 (Ø127 h8)
Flange SAE J744 127-2 (SAE 0.50 C) (12 .7)
V
3.94 (100) 3.94 (100) 3.94 (100) 3.94 (100)
0.50 (12 .7)Port plate 62 9.84 (250) 0.24 (6 ) 6.89 (175 )
S 2.36 (60 ) 3.50 (88.9 ) S 2.36 (60 ) 3.50 Valve mounting for counter (88.9 ) clockwise rotation
Valve mounting for counter Valve mounting for counter clockwise rotation
clockwise rotation
21
hydraut.com
Mounting Dimensions, Size 100 Dimensions, sizesize 100 100 Dimensions,
Series 31
Drive Drive shafts Drive shafts Shafts S Splined shaft 1 1/2 in117T S Splined shaft 1/212/24 in 17TDP 12/241) DP Splined shaft 1 1/2 in 17T 12/24 DP1) SAESJ744 - 38-4 SAE J744(C-C) - 38-4 (C-C) 1)
K Parallel with key K Parallel with key K Parallel with key ISO 3019-1 38-1 38-1 ISO 3019-1
1)
ISO 3019-1 38-1
DIA1 1/2in 7/16-14UNC-2B
DIA1 1/2in 7/16-14UNC-2B
SAE J744 - 38-4 (C-C)
1.10 (28)1.10 (28) 1.72 (43.6) 1.72 (43.6) 2.13 (54) 2.13 (54) 2.44 (62.44 1.9) (6 1.9)
DIA 1 1/4in 5/16-18UNC-2B
DIA 1 1/4in 5/16-18UNC-2B
1)
DIA 1 1/4in 5/16-18UNC-2B
J744 - 32-4 (C)
W Splined shaft 1 1/4 in 114T W Splined shaft 1/412/24 in 14TDP 12/241)DP 1) W Splined shaft 1 1/4 in 14T 12/24 DP1) SAE SAEJ744 J744 - 32-4 (C) SAE J744(C) - 32-4 1) (C) - 32-4
0.75 (190.75 ) (19 ) usable spline usablelength spline length1.38 (35) 1.38 (35)
0.75 (190.75 ) (19 ) 1.38 (35) 1.38 (35)
2.18 (55.4) 2.18 (55.4)
2.18 (55.4) 2.18 (55.4) 1)
DIA 1 1/4in 5/16-18UNC-2B
U Splined shaft 1 1/4 in 114T U Splined shaft 1/412/24 in 14TDP 12/241)DP 1) SAE J744 - 32-4 U Splined shaft 1/4 in SAE J744(C) -132-4 (C)14T 12/24 DP1) SAE
1)
1) ANSI ANSI B92. 1a-1976, 30° pressure angle, angle, at root side ank centering, tolerance class 5 class 5 B92.1a-1976, 30° pressure at roott, side t, ank centering, tolerance
Shaft P, ISO Flange A 4040mm mmØ0 Shaft Shaft
Ports Ports Ports H(S)P-10V 100
Designation Port forPort for Designation Designation
B
B
S
SB
L L1 X X
LS L1 L, L X 1 X X
2)
X
Port for
Standard Size Standard
Standard
2)
Size
2)
Size
Peak press. State State Peak press. 3) 3) Max press. [psiPeak (bar)] [psi (bar)]
Tightening [psi (bar)] ServiceService line (high range) range) SAE J518 1 1/4 in 1 1/4 in linepressure (high pressure SAE J518 Torque Fixing thread ISO 68 ISO 681/2-13 UNC-2B; 0.75 (19)0.75 deep O [lb-ftO(Nm)] Fixing thread 1/2-13 UNC-2B; (19) deep 5100 (350) 5100 (350)
Intlet (standard pressure range) SAE J518 2 1/2 in121/4 Intlet (standard pressure range) SAE 1/2inin Service line (high pressure range) SAEJ518 J518 Fixing thread thread ISO68 681/2-13 1/2-13 (19) deep 75 5100 (350) Fixing thread ISO 68 ISO UNC-2B; 1.06 (17)0.75 deep (5) 75 Fixing 1/2-13UNC-2B; UNC-2B; 1.06 (17) deep (5) O
66O(90)
State
O
O Intletdrain (standard pressure range) SAE11926 1/2 in UNF-2B Case drain ISO 11926 1J518 1/16-12 UNF-2B 30 (2) 30 (2) O 4) O 4) Case ISO 121/16-12 66 (90) Fixing thread ISO 68 1/2-13 UNC-2B; 1.06 (17) deep 75 (5) 4) Case drain ISO 11926 1 1/16-12 UNF-2BUNF-2B 30 (2) 30 (2) plugged Case drain ISO 11926 1 1/16-12 plugged 4)1) 265 (360) Case drain ISO 11926 1 1/16-12 UNF-2B 30 (2) O Pilot pressure ISO 11926 7/16-20 7/16-20 UNF-2B;UNF-2B; 0.39 (10)0.39 deep 5100 (350) O Pilot pressure ISO 11926 (10) deep 5100 (350) O 59 (80) Pilot pressure ISO 11926 7/16-20 UNF-2B; 0.39 (10) deep 5100 (350) O ControlControl pressure for DG control DIN 3852 R 1/4 inR 1/4 in 1740 (120) O pressure for DG control DIN 3852 1740 (120) O Control pressure for DG control
DIN 3852
R 1/4 in
1740 (120)
59 (80)
2) For For the max. tightening torquestorques the instructions on pageon 44page must44 bemust observed. the max. tightening the instructions be observed. 3) Application 3) dependent spikes can occur.. consider this when measuring equipment ttings ttings pressure spikes occur.. Please consider thisselecting when selecting measuring equipment 1) Application Dependent ondependent the pressure installation position, port Lcan or LPlease must be connected 1 4) Dependent 4) onbethe installation position, port L orport L 1 Lmust connected on the installation position, or L be O Dependent = Must connected 1 must be connected O = Must beMust connected (plugged on delivery)) O= be connected (plugged on delivery))
22
O
hydraut.com
Mounting Dimensions, Size 140
Series 31
H(S)P-10V140 Service ports on side; Non through drive, Models 62N00 and 12N00 mech. displacement limiter max.
View W Flange SAE J744 152-4 (D)
12N00 M12; 17 deep mech. displacement limiter min. mech. displacement limiter min.
View V
12N00 M14, 19 deep
mech. displacement limiter Shaft end
mech. displacement limiter max.
K Parallel with key ISO 3019-1 44-1
Designation
S Splined shaft 1 3/4 in 13T 8/16 DP SAE J744-44-4 (D)
Port for
Standard
Size
Peak Pressure [psi (bar]
Max Tightening Torque [lb-ft (Nm)]
B
Pressure port (standard pressure range) SAE J518 Threading in bolt holes ISO 68
1 1/4 in 1/2-13 UNC-2B; 0.75 (24) deep
5100 (350)
66 (90)
S
Inlet (standard pressure range) Threading in bolt holes
SAE J518 ISO 68
2 1/2 in 1/2-13 UNC-2B; 0.94 (24) deep
75 (5)
66 (90)
L,L1
Case drain (L1 plugged)
ISO 11926
1 1/16-12 UNF-2B
30 (2)
265 (360)
X
Pilot pressure
ISO 11926
9/16-18 UNF-2B; 0.51 (13) deep
5100 (350)
59 (80)
X
Control pressure for DG control
DIN 3852
M14 x 1.5; 0.47 (12) deep
1740 (120)
59 (80)
1) Dependent on the installation position, port L or L 1 must be connected O = Must be connected
23
hydraut.com
Through Drives Through Drive Mounting Options Shaft Torque Data Axial piston units H(S)P-10V can be supplied with a through drive as shown in the ordering code on page 3. T he type of through drive is determined by codes (K40-K...). If the combination pump is not mounted in the factory, t. Included in this case are: shaft coupler, seals, and if necessar Maximum permissible input and through drive torque.
T tot
T thr
The drive torques for pump 1 and pump 2 can be split up as required. However the max. permissible input torque T tot as well as the max. permissible through drive torque Tthr may not be exceeded. Max. perm. input torque T
18
tot
28
45
71
100
140
With U shaft U
T tot
lb.ft (Nm)
43 (59)
- (-)
139 (188)
- (-)
With shaft K
T
tot
lb.ft (Nm)
77 (104)
107 (145)
156 (212)
319 (433)
553 (750)
875 (1186)
With shaft S
T
tot
lb.ft (Nm)
92 (124)
146 (198)
235 (319)
462 (626)
814 (1104)
1195 (1620)
With shaft R
T
tot
lb.ft (Nm)
111 (150)
166 (225)
295 (400)
475 (644)
- (-)
77 (104)
107 (145)
156 (212)
319 (433)
553 (750)
875 (1186) 934 (1266)
Max. perm. through drive torque T
439 (595)
- (-)
- (-)
thr
W ith shaft K
T thr
lb.ft (Nm)
W ith shaft S
T thr
lb.ft (Nm)
80 (108)
118 (160)
235 (319)
363 (492)
574 (778)
W ith shaft R
T thr
lb.ft (Nm)
88 (120)
130 (176)
269 (365)
404 (548)
- (-)
Keyed shaft
T thr keyed lb.ft (Nm)
53 (72)
83 (112)
132 (179)
209 (283)
293 (398)
- (-) 411 (557)
T tot = max. permissible input torque pump 1 T thr = max. permissible through drive torque T thr keyed = max. permissible through drive torque at through drive to keyed shaft
Permissible overhang moment m1 , m2 , m3
weight of pump [lbs (kg)]
l1 , l 2 , l 3
distance to center of gravity [in (mm)] 1 12 1 ... • 102
T m = (m 1 • l 1 + m 2 • l 3 + m 3 • l 3 ) •
S iz e
18
28
45
71
Permissible overhang moment Tm
lb.ft (Nm)
369 (500) 649 (880) 1010 (1370) 1593 (2160)
at dyn. acceleration
Tm
lb.ft (Nm)
37 (50)
Weight
m
lbs (kg)
26,5 (12) 33 (15)
Distance to center of gravity
l1
in (mm)
3.54 (90) 4.33 (110) 5.12 (130)
10g = 98.1 m/s
65 (88)
101 (137)
159 (216)
[lb.ft] [Nm]
100
140
2213 (3000) 3319 (4500) 221 (300)
332 (450)
2
46 (21)
24
73 (33)
99 (45)
5.91 (150)
6.30 (160)
132 (60) 6.30 (160)
hydraut.com
Through Drives
RA 92 711/10.07 | (A)A10VSO Through Drives
Industrial Hydraulics | Bosch Rexroth AG
Overview of through drive mounting options
Through Drive Mounting Options H(S)P-10V
K02
127-2 (C)
Dimensions of Through Drives K01 FLANGE SAE J744 - 82-2 (A) Hub for splined shaft to ANSI B.92.1a-1976 5/8 in 9T 16/32 DP
1)
(SAE J744 - 16-4 (A)) Size
section A - B
18
thread
thread metric metric
25
A
1
A3
A4
7.16 (182)
0.57 (14,5)
1.65 (42)
28
8.03 (204)
0.63 (16)
1.85 (47)
45
9.02 (229)
0.63 (16)
2.09 (53)
71
10.51 (267)
0.79 (20)
2.40 (61)
100
13.31 (338)
0.79 (20)
2.56 (65)
140
13.78 (350)
0.63 (17)
3.03 (77)
27
/36
hydraut.com
Through Drives Dimensions of Through Drives K52 FLANGE SAE J744 - 82-2 (A) Hub for splined shaft to ANSI B.92.1a-1976 3/4 in 11T 16/32 DP
(SAE J744 - 19-4 (A-B))
1)
Size A section A - B 45
A
°
18
A4
28
A3
45
3.2520
DIA3.2508 A 5 (ø82.55+0.050 +0.020)
9 4.1 DIA 6.5) 0 1 (ø
71 100
0.39 (10)
B
A2
A5
thread metric
A1
140
1
7.16
A2 1.57
A3
A4
0.74
1.69
(182)
(40)
(18,8)
(43)
8.03
1.53
0.74
1.85
(204)
(39)
(18,8)
(47)
9.02
1.59
0.75
(229)
(40,5) (18,9)
(53)
10.51
1.57
0.84
2.40
(267)
(40)
(21,3)
(61)
13.31
1.57
0.75
2.56
(338)
(40)
(19)
(65)
13.78
1.61
0.75
3.03
(350)
(41)
(18,9)
(77)
2.09
A5 M10; 0.57 (14,5) deep M10; 0.63 (16) deep M10; 0.63 (16) deep M10; 0.79 (20) deep M10; 0.79 (20) deep M10; 0.67 (17) deep
K02/K68 FLANGE SAE J744 - 101-2 (B) Hub for splined shaft to ANSI B.92.1a-1976 7/8 in 13T 16/32 DP
(SAE J744 - 22-4 (B))
1)
Size A section A - B 45 °
A3
)
)
A5
71
+0.050 +0.020
46
.7 5
100
A5
A5
45
(ø101.6
(ø1
140
0.39 (10)
B
A2
e
thread metric
A1
1)
1)
A3
8.03
1.69
0.70
1.85
(204)
(43)
(17,8)
(47)
9.02
1.65
0.70
2.09
(229)
(42)
(17,9)
(53)
10.51
1.69
0.80
2.40
(267)
(43)
(20,3) (61)
13.31
1.61
0.71
2.56
(338)
(41)
(18)
(65)
13.78
1.73
0.70
3.03
(350)
(44)
(17,9)
(77)
45
A4
45 A3
71 100
(ø101,6
+0,050 +0,020 )
4.0020
DIA 4.0008
5 5.7 DIA 46) 1 (ø
140
0.39 (10)
B A1
A5 M12; 0.71 (18) deep M12; 0.71 (18) deep M12; 0.79 (20) deep M12; 0.79 (20) deep M12; 0.79 (20) deep
pressure angle 30 °
Size A section A - B A
A4
5
(SAE J744 - 25-4 (B-B))
A5
DI
28
A4
DIA 4.0020 4.0008
omitted on size 28
A
A2
1
A2
thread metric
26
1
A2
A3
A4
9.02
1.87
0.73
2.09
(229)
(47,5)
(18,4)
(53)
10.51
1.87
0.82
2.40
(267)
(47,5) (20,8) (61)
13.31
1.87
0.72
2.56
(338)
(47,5)
(18,2)
(65)
13.78
1.87
0.73
3.03
(350)
(47,5)
(18,4)
(77)
A5 M12; 0.71 (18) deep M12; 0.79 (20) deep M12; 0.79 (20) deep M12; 0.79 (20) deep
hydraut.com
Through Drives Dimensions of Through Drives K07 FLANGE SAE J744 - 127-2 (C) Hub for splined shaft to ANSI B.92.1a-1976 1 1/4 in 14T 12/24 DP
1)
(SAE J744 - 32-4 (C))
Size A section A - B A3
100
omitted on size 71
B
140
+0.050 +0.020 )
5.0020
7.13 DIA ) 1 (ø18
71
A4
DIA 5.0008
A
A5 thread metric
(ø127
omitted on size 71
45
A2
A3
10.51
2.18
0.87
(267)
(55,5) (22)
1
A4 2.40
A5 M16; 0.70 (18) deep
(61)
13.31
2.24
0.77
2.56
(338)
(57)
(19,5)
(65)
13.78
2.36
0.77
3.03
(350)
(60)
(19,4)
(77)
M16; 0.95 (24) deep M16; 0.95 (24) deep
0.51 (13) A2 A1
K24 FLANGE SAE J744 - 127-2 (C) Hub for splined shaft to ANSI B.92.1a-1976 1 1/2 in 17T 12/24 DP
1)
(SAE J744 - 38-4 (C-C))
Size section A - B
A
A3
1
A4
100
13.31 (338)
0.95 (24)
2.56 (65)
140
13.78 (350)
0.95 (34)
3.03 (77)
thread metric
1)
pressure angle 30 °
Dimensions of through drives K17 FLANGE SAE J744 - 152-4 (D) Hub for splined shaft to ANSI B.92.1a-1976 1 3/4 in 13T 8/16 DP
1)
section A - B
thread metric
27
(SAE J744 - 44-4 (D))
Size
A
140
13.78 (350
1
A3
A4
approx. 0.83 (ca. 21)
3.03 (77)
hydraut.com
Pump Installation Notes 34/36
Bosch Rexroth AG
| Industrial Hydraulics
(A )A10VSO | RA 92 711/10.07
Installation Notes ρ =density [kg/m 3 ] l = pipe lenth [m] In order to attain the lowest noise level, all connections members to tank. Avoid placing a check valve in the case drain line. The case drain hose corresponding to the size of the case drain port should be installed at the highest case drain port location.
Vertical installation (shaft end upwards)
Following installation conditions must be taken into account: Arrangement inside the reservoir
2
]
Δp2 : Pressure lodd due to static head Δp2 = h . ρ . g . 10 –5 [bar] h = head [m] ρ = density [kg/m 3 ] g = gravity. = 9,81 m/s 2 Δp3 : line losses (elbows etc.)
Horizontal installation The pump must be installaed in such a manner, that either “L“ or “L1“ is at the top. Arrangement inside the reservoir
position.
Close “L 1 ” , "L" and “S” open, mount suction pipe to port S, and pipe “L“ at least 200 mm away from suction pipe.
surface: Close port “L“, "L 1 " and “S” open; L 1 piped and also S with
1
(compare limiting conditions) item limiting conditions) Note: In order to avoid damages to the pump, all attached parts (e.g. protective caps, covers, etc.) must be removed before installation. Fluid
" closed.
Note: In order to avoid damages to the pump, all attached parts (e.g. protective caps, covers, etc.) must be removed before installation. Fluid L
min. 8 in (200mm)
S
L1
S
ht min
L
L1 min. 8 in (200mm)
Arrangement outside the reservoir
Arrangement outside the reservoir
Fill pump housing before commissioning. Pipe port “S“ and the higher port “L“ or “L 1 “ item limiting conditions)
Min. pump inlet pressure p abs min = 12 psi (0,8 bar) under static and dynamic loading.
b) Mounting below the reservoir: pipe ports “L“ and “S“
Note: Avoid mounting above tank wherever possible in order to attain a low noise level.
L
The permissible suction height h is a result of the overall pressure loss, but may not be greater than h max = 31.5 in (800 mm) (Immersion depth ht min = 8 in/200 mm).
Fluid
L1
L
L1
S
ht min hmax
S Fluid
ht min
Fluid
Overall pressure loss ΔpGes = Δp1 + Δp2 + Δp3 ≤ (1 – p Δp1
ht min hmax
Limiting condition:
abs min
) = 0,2 bar
L1 S
ρ . l . dv . –5 10 [bar] Δp1 = dt
L
28
hydraut.com
RANGE OF PRODUCTS
Single • Double • Thru-Drive Vane Pumps
Variable Displacement Pump H(S)P-10V
Directional Control Valve
Hydraulic Cylinders
hydraut.com
