Up to 2 HighRollers: 16 minimum crossbar spread More than 2 HighRollers: 18 minimum crossbar spread Maximum crossbar spread is 46

HighRoller CROSSBAR SPREADS • Up to 2 HighRollers: 16” minimum crossbar spread • More than 2 HighRollers: 18” minimum crossbar spread • Maximum crossb...
Author: Phillip Rodgers
5 downloads 0 Views 2MB Size
HighRoller CROSSBAR SPREADS • Up to 2 HighRollers: 16” minimum crossbar spread • More than 2 HighRollers: 18” minimum crossbar spread • Maximum crossbar spread is 46”

Wheel Grip

Wheel Strap 1x Big Hoop Small Hoop Rear Wheel Tray

Adjuster Knob

Thumbwheel 2x

Red Button

Wheeltray Bolt (longer) 1x Snap Around 3x Hex Key 1x

Baseplate

Baseplate Cover 2x Hex bolts 2x

Snap Around (3x) Baseplate Bolts (shorter) 2x

(optional MightyMount attachments)



IMPORTANT WARNING!

IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER SUCH AS A QUALIFIED GARAGE OR AUTO BODY SHOP.

Part #1033349 Rev.E

1033349E-/21

Do you have - square - round - or OTHER - crossbars?

SQUARE

Remove the tabs with scissors or pliers.

Loosen the tabs in the SnapArounds by bending them repeatedly.

• Attach 1 SnapAround on rear bar for wheeltray. • Attach 2 SnapArounds on front bar for baseplate.

HATCH INTERFERENCE: HighRoller can face opposite direction when there is hatch interference.

+

round

OTHER

• Attach 1 SnapAround on rear bar for wheeltray. • Attach 2 SnapArounds on front bar for baseplate.

HATCH INTERFERENCE: HighRoller can face opposite direction when there is hatch interference.

+

MIGHTYMOUNTS: • Attach 2 MightyMounts on the rear bar and 1 on the front bar. • If your MightyMounts require bar caps, install them now. MightyMounts purchased separately (refer to the YAKIMA Fit List for correct MightyMounts for your vehicle).

Universal MightyMount #03590 1033349E-/21

Follow the Universal MightyMount instructions and refer to this instruction for correct installation.

Lift both hoops until they stop.

Position mount anywhere on crossbars.

Insert short baseplate bolts through bottom of SnapArounds into baseplate. LOOSELY attach thumbwheels.

Remove baseplate cover. Press sides and lift to expose bolt holes.

If you position the front mount straddling a tower, the wheel tray can attach to either side of the rear tower.

MightyMount users: • Remove embedded nut in thumbwheel. • Push hex bolt into top of knob until fully seated. • Insert hexogaonal bolts through thumbwheels into baseplate. • LOOSELY attach thumbwheels.

Slide wheeltray bolt into rear end of wheeltray.

Align bolt to hole...

MightyMount users: Remove embedded nut in MightyMount.

1033349E-/21

Secure with Hex Key.

Tighten Thumb Wheels.

Move big hoop forward.

Replace baseplate covers. (They should snap into place).

Find the tire size of your front wheel.

ATTACH WHEEL STRAP • Insert one end of strap into slot on far side of Wheeltray. • Leave other end free.

Open wheel grip handle.

DO NOT USE MOUNT WITH WHEELS UNDER 20" Slide wheel grip until it aligns to your tire size.

Some downhill tires may require a higher setting. The wheel grip handle must align to a number before it will close.

While holding small hoop, press red button.

1033349E-/21

Small hoop should lay flat.

Lift bike and place front wheel in front hoop.

Roll bicycle forward in front tray.

Lift small hoop to rest against tire.

TIGHTEN ADJUSTMENT KNOB.

Smaller hoop should compress against tire. If wheel moves, tighten more. CENTER TIRE IN WHEELGRIP.

See your lock instructions for installing lock. Loop cable around frame and insert silver post into lock housing.

Close the strap. • Insert strap end behind buckle. • Tighten strap by repeatedly lifting buckle. • DO NOT OVERTIGHTEN.

1033349E-/21

Lock your HighRoller between towers on crossbar when not in use.

Pull the strap through wheel spokes.

Do not let the strap push against the valve stem.

CHECK TIRE FOR TIGHT FIT. • If not tight, loosen strap. • Adjust position of strap and strap base until strap rests against rim. • TIGHTEN strap again.

Keep strap centered on small wheels.

UNLOAD BIKE: To release rear strap, push tab in buckle.

Support small hoop. Press red button.

FRONT WHEEL Loosen adjustment knob until small hoop is loosened.

Support bike. Lay hoop flat.

Small hoop will lower.

Roll back and lift bike out. Lower both hoops when not in use.

Before driving away: Check front wheel attachment to bicycle fORK. If there is contact, check wheel setting.

make sure your tires are filled to recommended pressure FOUND ON THE TIRE.

Check the front wheel.

If it is loose or it moves, be sure knob is tight and wheel is centered!

Check the rear wheel. Tighten the strap if needed.

Do not overtighten the strap! 1033349E-/21

Check the Hex key and the oblong knobs. If they are loose, tighten them.

Off-road driving is not recommended and could result in damage to your vehicle or your bike.

weight limits Follow the YAKIMA Fit List or your owner’s manual for your rack’s weight limit. Do not exceed the factory weight limit of your vehicle’s racks. Maximum rack’s weight is 165 lbs. (75 kg) unless otherwise noted.

BIKE weight limit: Maximum bike weight is 50 lbs. (23 kg).

Do not transport bicycles with attached baby seats, panniers, wheel covers, full bike covers or motors.

YAKIMA Accessory locks can lock the mounts to the racks (lock housings purchased separately)

If you remove your carrier, follow instructions to install. Follow safety checks in accessory instructions before every installation.

REAR HATCH Some longer loads may prevent the rear hatch from fully opening. ALWAYS USE CAUTION WHEN OPENING YOUR HATCH.

• There must be adequate clearance for installing accessory locks. • If the accessory lock housing comes in contact with the vehicle, even after loading the rack, do not install them.

MAINTENANCE: Use non-water soluble lubricant on screws. Use a soft cloth wit water and mild detergent to clean plastic parts. REMOVE ACCESSORY BEFORE ENTERING AN AUTOMATIC CAR WASH.

WARNING Be sure all hardware is secured according to instructions. Attachment hardware can loosen over time. Check before each use, and tighten if necessary.

TECHNICAL ASSISTANCE OR REPLACEMENT PARTS Contact your dealer or call (888)925-4621 Monday through Friday, 7:00 AM to 5:00 PM, PST

This product is covered by YAKIMA's “Love It Till You Leave It” Limited Lifetime Warranty To obtain a copy of this warranty, go online to www.yakima.com or email us at [email protected] or call (888) 925-4621 1033349E-/21

KEEP

THESE

INSTRUCTIONS!