Technical specification Submersible pump L 3085, 60 Hz

L 3085 Y/D start SUBCAB®

7G2,5 mm2

VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft

Stainless steel

O-rings

Nitrile rubber

Mechanical face seals

L 3085 Product

Impeller characteristic

max. 1100 kg/m

Leakage sensor in stator housing Surface treatment

Voltage imbalance between phases No. of starts/hour

See Motor rating table

Accessories Electrical accessories such as pump controller, control panels, starters, monitoring relays.

60 Hz H (+180° C)

See separate booklet or www.flygt.com, for further information.

max ± 5% max ± 10% max 2% max 30

Cable Direct-on-line start SUBCAB®

Epoxy treatment

Zinc anodes

Voltage variation - intermittent running

FLS

Other cables

3

Motor data

- continuously running

Ex. proof version

Warm liquid version on request

max +40° C pH 5,5-14

Insulation class

Silicon carbide/ Silicon carbide

3085.092

The pH of the pumped liquid

Frequency

Carbon/Aluminium oxide

Option

LT

max 20 m

Impeller throughlet

2

See dimensional drawing.

L

Depth of immersion Liquid density

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Weight

3085.183

Process data Liquid temperature

Outer seal

Carbon/Aluminium oxide

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

Denomination Installation

Inner seal

1

Surface Treatment

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Product code

Alternative

4G1,5 mm2 4G1,5+2x1,5 mm2 4G2,5 mm2 4G2,5+2x1,5 mm2

2

L 3085

3.5

2,2

4,5

24,0

0,80

80

2.5

3.0 2.5 2.0

2.0 1.5 414

1.5 H [m] / [ft]

LT

460 V, 60 Hz, 3 ~, 1710 r/min 414

P2 [kW] / [hp]

4.0

Ex proof version available

Impeller thoughlet, mm

Power factor cos ϕ

Starting current, A

Rated current, A

Rated power, kW

Curve/Impeller No

LT - Motor rating and performance curve

20

6

16

5

Yes

4 12 3 8 2 4

1 414

0

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg).Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm

3

0 0

5

0

100

10

15

200

20 300

25 400

30

35

40

500 600 700 Q [l/s] / [usgpm]

L3085.60Hz.04.01.EN.FIN.04.08 © ITT Flygt AB

www.flygt.com

894915

Technical specification Submersible pump L 3085, 60 Hz

L 3085 Y/D start SUBCAB®

7G2,5 mm2

VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft

Stainless steel

O-rings

Nitrile rubber

Mechanical face seals

L 3085 Product

Impeller characteristic

max. 1100 kg/m

Leakage sensor in stator housing Surface treatment

Voltage imbalance between phases No. of starts/hour

See Motor rating table

Accessories Electrical accessories such as pump controller, control panels, starters, monitoring relays.

60 Hz H (+180° C)

See separate booklet or www.flygt.com, for further information.

max ± 5% max ± 10% max 2% max 30

Cable Direct-on-line start SUBCAB®

Epoxy treatment

Zinc anodes

Voltage variation - intermittent running

FLS

Other cables

3

Motor data

- continuously running

Ex. proof version

Warm liquid version on request

max +40° C pH 5,5-14

Insulation class

Silicon carbide/ Silicon carbide

3085.092

The pH of the pumped liquid

Frequency

Carbon/Aluminium oxide

Option

LT

max 20 m

Impeller throughlet

2

See dimensional drawing.

L

Depth of immersion Liquid density

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Weight

3085.183

Process data Liquid temperature

Outer seal

Carbon/Aluminium oxide

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

Denomination Installation

Inner seal

1

Surface Treatment

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Product code

Alternative

4G1,5 mm2 4G1,5+2x1,5 mm2 4G2,5 mm2 4G2,5+2x1,5 mm2

2

L 3085

3.5

2,2

4,5

24,0

0,80

80

2.5

3.0 2.5 2.0

2.0 1.5 414

1.5 H [m] / [ft]

LT

460 V, 60 Hz, 3 ~, 1710 r/min 414

P2 [kW] / [hp]

4.0

Ex proof version available

Impeller thoughlet, mm

Power factor cos ϕ

Starting current, A

Rated current, A

Rated power, kW

Curve/Impeller No

LT - Motor rating and performance curve

20

6

16

5

Yes

4 12 3 8 2 4

1 414

0

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg).Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm

3

0 0

5

0

100

10

15

200

20 300

25 400

30

35

40

500 600 700 Q [l/s] / [usgpm]

L3085.60Hz.04.01.EN.FIN.04.08 © ITT Flygt AB

www.flygt.com

894915

Technical specification Submersible pump L 3102, 60 Hz

L 3102 VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft

Stainless steel

O-rings

Nitrile rubber

Mechanical face seals

L 3102 Product

Alternative

Inner seal

Outer seal

1

Carbon/Aluminium oxide

Aluminium oxide/ Corrosion resistant cemented carbide

2

Carbon/Aluminium oxide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

3

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Aluminium oxide/ Corrosion resistant cemented carbide

4

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Denomination Product code Installation Impeller characteristic

3102.181 L

Surface Treatment

LT

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

Process data Liquid temperature

max 20 m

The pH of the pumped liquid

pH 5,5-14

Liquid density Impeller throughlet

Weight

max +40° C

Depth of immersion

See dimensional drawing.

Option

max. 1100 kg/m3 See Motor rating table

3102.090

Motor data Frequency Insulation class

60 Hz H (+180° C)

- intermittent running Voltage imbalance between phases No. of starts/hour

SUBCAB®

Leakage sensor in oil housing

CLS Epoxy treatment

Zinc anodes

max ± 10%

Accessories

max 2% max 30

Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information. 4G2,5 mm2 4G2,5+2x1,5 mm2

Y/D start SUBCAB®

FLS

Surface treatment

max ± 5%

Cable Direct-on-line start

Leakage sensor in stator housing Other cables

Voltage variation - continuously running

Ex. proof version

Warm liquid version on request

7G2,5 mm2 7G2,5+2x1,5 mm2

3

L 3102 LT - Motor rating and performance curve

6

Impeller L

5

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

6,8

41,0

0,81

52

Yes

412

3,7

6,8

41,0

0,81

54

Yes

Rated current, A

3,7

Rated power, kW

Starting current, A

4.0

411

Curve/Impeller No

P2 [kW] / [hp]

3.5 3.0

4

2.5 3

411

2.0 412

H [m] / [ft]

LT 8

25

460 V, 60 Hz, 3 ~, 1745 r/min

7 20

6

Y/D starting current is approximately 1/3 of D starting current.

5 15 4 10

3 2

5

411

1 0

0

LT - Motor rating and performance curve

0

20

200

30

400

40 600

50 800

60

1000 1200 Q [l/s] / [usgpm]

Starting current, A

Power factor cos ϕ

Ex proof version available

41,0

0,81

Yes

4.0 5.5

3.6 423

3.2

H [ft] / [m]

460 V, 60 Hz, 3 ~, 1745 r/min 423

3,7

70

P [hp] / [kW]

Rated current, A

Rated power, kW

10

0

Impeller NL

Curve/Impeller No

412

6,8

LT 8

25

Y/D starting current is approximately 1/3 of D starting current.

7

20

6 5

15 4

10

3 2

5 1

423

0 0

0

4

10

200

20

30

400

40

600

50

800

60

70

1000 1200 Q [l/s] / [usgpm]

L 3102 Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

LT, L-installation

LT, L-installation

5

L 3102

6

L3102.60Hz.EN.FIN.04.08 © ITT Flygt AB

www.flygt.com

894907

Technical specification Submersible pump L 3102, 60 Hz

L 3102 VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft

Stainless steel

O-rings

Nitrile rubber

Mechanical face seals

L 3102 Product

Alternative

Inner seal

Outer seal

1

Carbon/Aluminium oxide

Aluminium oxide/ Corrosion resistant cemented carbide

2

Carbon/Aluminium oxide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

3

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Aluminium oxide/ Corrosion resistant cemented carbide

4

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Denomination Product code Installation Impeller characteristic

3102.181 L

Surface Treatment

LT

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

Process data Liquid temperature

max 20 m

The pH of the pumped liquid

pH 5,5-14

Liquid density Impeller throughlet

Weight

max +40° C

Depth of immersion

See dimensional drawing.

Option

max. 1100 kg/m3 See Motor rating table

3102.090

Motor data Frequency Insulation class

60 Hz H (+180° C)

- intermittent running Voltage imbalance between phases No. of starts/hour

SUBCAB®

Leakage sensor in oil housing

CLS Epoxy treatment

Zinc anodes

max ± 10%

Accessories

max 2% max 30

Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information. 4G2,5 mm2 4G2,5+2x1,5 mm2

Y/D start SUBCAB®

FLS

Surface treatment

max ± 5%

Cable Direct-on-line start

Leakage sensor in stator housing Other cables

Voltage variation - continuously running

Ex. proof version

Warm liquid version on request

7G2,5 mm2 7G2,5+2x1,5 mm2

3

L 3102 LT - Motor rating and performance curve

6

Impeller L

5

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

6,8

41,0

0,81

52

Yes

412

3,7

6,8

41,0

0,81

54

Yes

Rated current, A

3,7

Rated power, kW

Starting current, A

4.0

411

Curve/Impeller No

P2 [kW] / [hp]

3.5 3.0

4

2.5 3

411

2.0 412

H [m] / [ft]

LT 8

25

460 V, 60 Hz, 3 ~, 1745 r/min

7 20

6

Y/D starting current is approximately 1/3 of D starting current.

5 15 4 10

3 2

5

411

1 0

0

LT - Motor rating and performance curve

0

20

200

30

400

40 600

50 800

60

1000 1200 Q [l/s] / [usgpm]

Starting current, A

Power factor cos ϕ

Ex proof version available

41,0

0,81

Yes

4.0 5.5

3.6 423

3.2

H [ft] / [m]

460 V, 60 Hz, 3 ~, 1745 r/min 423

3,7

70

P [hp] / [kW]

Rated current, A

Rated power, kW

10

0

Impeller NL

Curve/Impeller No

412

6,8

LT 8

25

Y/D starting current is approximately 1/3 of D starting current.

7

20

6 5

15 4

10

3 2

5 1

423

0 0

0

4

10

200

20

30

400

40

600

50

800

60

70

1000 1200 Q [l/s] / [usgpm]

L 3102 Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

LT, L-installation

LT, L-installation

5

L 3102

6

L3102.60Hz.EN.FIN.04.08 © ITT Flygt AB

www.flygt.com

894907

Technical specification Submersible pump L 3127, 60 Hz

L 3127 Y/D start SUBCAB®

7G2,5 mm2 7G2,5+2x1,5 mm2 7G4+2x1,5 mm2

VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft

Stainless steel

O-rings

Nitrile rubber

Mechanical face seals

L 3127

Alternative

Inner seal

Outer seal

1

Carbon/Aluminium oxide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

2

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

3

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Silicone carbide/ Silicone carbide

Product Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Denomination Product code Installation Impeller characteristic

3127.181 L LT

Surface Treatment

Process data Liquid temperature Depth of immersion The pH of the pumped liquid Liquid density Impeller throughlet

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint. max +40° C

Weight

max 20 m pH 5,5-14

See dimensional drawing.

max. 1100 kg/m3

Option

See Motor rating table

Motor data Frequency Insulation class

3127.090 60 Hz H (+180° C)

Voltage variation - continuously running - intermittent running Voltage imbalance between phases No. of starts/hour

SUBCAB®

Leakage sensor in stator housing

FLS

Leakage sensor in oil housing

CLS

Other cables max ± 5%

Surface treatment

max ± 10%

Epoxy treatment

Zinc anodes

max 2%

Accessories

max 30

Cable Direct-on-line start

Ex. proof version

Warm liquid version on request

Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information. 4G2,5 mm2 4G2,5+2x1,5 mm2 4G4 mm2 4G4+2x1,5 mm2

3

L 3127

Impeller L

10

P2 [kW] / [hp]

Ex proof version available

Impeller thoughlet, mm

Power factor cos ϕ

Starting current, A

8

Rated current, A

Rated power, kW

12

Curve/Impeller No

LT - Motor rating and performance curve

7 6

8 6

4

5,6

9,8

LT

35 10

60,0

0,85

76

Yes

30 25

460 V, 60 Hz, 3 ~, 1745 r/min 411

7,5

13,0

75,0

0,87

76

Yes

412

7,5

13,0

75,0

0,87

76

Yes

58,0

0,96

76

Yes

5,6

30,0

8

20

230 V, 60 Hz, 1 ~, 1745 r/min 412

412

H [m] / [ft]

460 V, 60 Hz, 3 ~, 1750 r/min 412

411

5

6

15 4 10

Y/D starting current is approximately 1/3 of D starting current.

2

5

411

412

0

0 0 0

Impeller NL

10

Starting current, A

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

5,6

400

60 800

80 1200

100

120

1600 2000 Q [l/s] / [usgpm]

P [hp] / [kW]

62,0

0,85

45

Yes

7

8

9,9

421

6 5

422

6

H [ft] / [m]

LT 16

50

460 V, 60 Hz, 3 ~, 1750 r/min 422

40

8

Rated current, A

Rated power, kW

12

Curve/Impeller No

LT - Motor rating and performance curve

20

14

40

460 V, 60 Hz, 3 ~, 1745 r/min 421

7,5

13,0

75,0

0,87

45

Yes

422

7,5

13,0

75,0

0,87

45

Yes

12 10

30 8

Y/D starting current is approximately 1/3 of D starting current.

20

6 4

10 2 421 422

0 0 0

4

20 400

40

60 800

80 1200

100

120

1600 2000 Q [l/s] / [usgpm]

L 3127 Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

LT,L-installation

5

L 3127

6

L3127.60Hz.04.01.EN.FIN.01.08 © ITT Flygt AB

www.flygt.com

894919

Technical specification Submersible pump L 3127, 60 Hz

L 3127 Y/D start SUBCAB®

7G2,5 mm2 7G2,5+2x1,5 mm2 7G4+2x1,5 mm2

VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft

Stainless steel

O-rings

Nitrile rubber

Mechanical face seals

L 3127

Alternative

Inner seal

Outer seal

1

Carbon/Aluminium oxide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

2

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

3

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Silicone carbide/ Silicone carbide

Product Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Denomination Product code Installation Impeller characteristic

3127.181 L LT

Surface Treatment

Process data Liquid temperature Depth of immersion The pH of the pumped liquid Liquid density Impeller throughlet

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint. max +40° C

Weight

max 20 m pH 5,5-14

See dimensional drawing.

max. 1100 kg/m3

Option

See Motor rating table

Motor data Frequency Insulation class

3127.090 60 Hz H (+180° C)

Voltage variation - continuously running - intermittent running Voltage imbalance between phases No. of starts/hour

SUBCAB®

Leakage sensor in stator housing

FLS

Leakage sensor in oil housing

CLS

Other cables max ± 5%

Surface treatment

max ± 10%

Epoxy treatment

Zinc anodes

max 2%

Accessories

max 30

Cable Direct-on-line start

Ex. proof version

Warm liquid version on request

Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information. 4G2,5 mm2 4G2,5+2x1,5 mm2 4G4 mm2 4G4+2x1,5 mm2

3

L 3127

Impeller L

10

P2 [kW] / [hp]

Ex proof version available

Impeller thoughlet, mm

Power factor cos ϕ

Starting current, A

8

Rated current, A

Rated power, kW

12

Curve/Impeller No

LT - Motor rating and performance curve

7 6

8 6

4

5,6

9,8

LT

35 10

60,0

0,85

76

Yes

30 25

460 V, 60 Hz, 3 ~, 1745 r/min 411

7,5

13,0

75,0

0,87

76

Yes

412

7,5

13,0

75,0

0,87

76

Yes

58,0

0,96

76

Yes

5,6

30,0

8

20

230 V, 60 Hz, 1 ~, 1745 r/min 412

412

H [m] / [ft]

460 V, 60 Hz, 3 ~, 1750 r/min 412

411

5

6

15 4 10

Y/D starting current is approximately 1/3 of D starting current.

2

5

411

412

0

0 0 0

Impeller NL

10

Starting current, A

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

5,6

400

60 800

80 1200

100

120

1600 2000 Q [l/s] / [usgpm]

P [hp] / [kW]

62,0

0,85

45

Yes

7

8

9,9

421

6 5

422

6

H [ft] / [m]

LT 16

50

460 V, 60 Hz, 3 ~, 1750 r/min 422

40

8

Rated current, A

Rated power, kW

12

Curve/Impeller No

LT - Motor rating and performance curve

20

14

40

460 V, 60 Hz, 3 ~, 1745 r/min 421

7,5

13,0

75,0

0,87

45

Yes

422

7,5

13,0

75,0

0,87

45

Yes

12 10

30 8

Y/D starting current is approximately 1/3 of D starting current.

20

6 4

10 2 421 422

0 0 0

4

20 400

40

60 800

80 1200

100

120

1600 2000 Q [l/s] / [usgpm]

L 3127 Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

LT,L-installation

5

L 3127

6

L3127.60Hz.04.01.EN.FIN.01.08 © ITT Flygt AB

www.flygt.com

894919

Technical specification Submersible pump L 3152, 60 Hz

L 3152 Y/D start SUBCAB®

7G2,5+2x1,5 mm2 7G4+2x1,5 mm2 7G6+2x1,5 mm2

VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St 3x6+3x6/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft O-rings

L 3152 Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Alternative

Inner seal

Outer seal

1

Corrosion resistant cemented carbide/ Carbon

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

2

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Denomination Installation Impeller characteristic

3152.181

Surface Treatment

L

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

LT

Process data Liquid temperature

Weight max +40° C

Depth of immersion

max 20 m

The pH of the pumped liquid

pH 5,5-14

Liquid density Impeller throughlet

max. 1100 kg/m

See dimensional drawing.

Option

3

3152.091

See Motor rating table

Insulation class

60 Hz

- intermittent running Voltage imbalance between phases No. of starts/hour

SUBCAB®

FLS

Leakage sensor in oil housing

CLS

Surface treatment

Epoxy treatment

Zinc anodes max ± 5%

Accessories

max ± 10% max 2%

Electrical accessories such as pump controller, control panels, starters, monitoring relays.

max 30

See separate booklet or www.flygt.com, for further information.

Cable Direct-on-line start

Leakage sensor in stator housing Other cables

H (+180° C)

Voltage variation - continuously running

Ex. proof version

Warm liquid version on request

Motor data Frequency

Nitrile rubber

Mechanical face seals

Product

Product code

Stainless steel

4G2,5+2x1,5 mm2 4G6+2x1,5 mm2 4G10+2x1,5 mm2

2

L 3152 LT - Motor rating and performance curve

P2 [kW] / [hp]

0,85

102

Yes

20

98,0

0,85

102

Yes

624

10,4

18,0

98,0

0,85

102

Yes

Impeller thoughlet, mm

98,0

18,0

Power factor cos ϕ

18,0

10,4

Starting current, A

10,4

622

Rated current, A

620

Rated power, kW

14

Curve/Impeller No

Ex proof version available

16

12 10

12 11 10 9 620

8

622

7 624

H [m] / [ft] 25

LT 7

460 V, 60 Hz, 3 ~, 1160 r/min

6 5

15 Y/D starting current is approximately 1/3 of D starting current.

4 10

3 2

5 1 620 624

0

0 0

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

3

622

0 50 500

100

150

200

250

1000 2000 3000 4000 1500 2500 3500 4500 Q [l/s] / [usgpm]

L3152.60Hz.04.01.EN.FIN.01.08 © ITT Flygt AB

www.flygt.com

895246

Technical specification Submersible pump L 3152, 60 Hz

L 3152 Y/D start SUBCAB®

7G2,5+2x1,5 mm2 7G4+2x1,5 mm2 7G6+2x1,5 mm2

VFD Application NSSHÖU../3E+St

3x2,5+3x2,5/3E+3x1,5 St 3x6+3x6/3E+3x1,5 St

Monitoring equipment Thermal contacts opening temperature

125° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

Shaft O-rings

L 3152 Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Alternative

Inner seal

Outer seal

1

Corrosion resistant cemented carbide/ Carbon

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

2

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Denomination Installation Impeller characteristic

3152.181

Surface Treatment

L

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

LT

Process data Liquid temperature

Weight max +40° C

Depth of immersion

max 20 m

The pH of the pumped liquid

pH 5,5-14

Liquid density Impeller throughlet

max. 1100 kg/m

See dimensional drawing.

Option

3

3152.091

See Motor rating table

Insulation class

60 Hz

- intermittent running Voltage imbalance between phases No. of starts/hour

SUBCAB®

FLS

Leakage sensor in oil housing

CLS

Surface treatment

Epoxy treatment

Zinc anodes max ± 5%

Accessories

max ± 10% max 2%

Electrical accessories such as pump controller, control panels, starters, monitoring relays.

max 30

See separate booklet or www.flygt.com, for further information.

Cable Direct-on-line start

Leakage sensor in stator housing Other cables

H (+180° C)

Voltage variation - continuously running

Ex. proof version

Warm liquid version on request

Motor data Frequency

Nitrile rubber

Mechanical face seals

Product

Product code

Stainless steel

4G2,5+2x1,5 mm2 4G6+2x1,5 mm2 4G10+2x1,5 mm2

2

L 3152 LT - Motor rating and performance curve

P2 [kW] / [hp]

0,85

102

Yes

20

98,0

0,85

102

Yes

624

10,4

18,0

98,0

0,85

102

Yes

Impeller thoughlet, mm

98,0

18,0

Power factor cos ϕ

18,0

10,4

Starting current, A

10,4

622

Rated current, A

620

Rated power, kW

14

Curve/Impeller No

Ex proof version available

16

12 10

12 11 10 9 620

8

622

7 624

H [m] / [ft] 25

LT 7

460 V, 60 Hz, 3 ~, 1160 r/min

6 5

15 Y/D starting current is approximately 1/3 of D starting current.

4 10

3 2

5 1 620 624

0

0 0

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

3

622

0 50 500

100

150

200

250

1000 2000 3000 4000 1500 2500 3500 4500 Q [l/s] / [usgpm]

L3152.60Hz.04.01.EN.FIN.01.08 © ITT Flygt AB

www.flygt.com

895246

Technical specification Submersible pump L 3201, 60 Hz

L 3201 SUBCAB®

4G35 mm2 4G35+2x1,5 mm2

Y/D start SUBCAB®

7G6+2x1,5 mm2

VFD Application NSSHÖU../3E+St

3x16+3x16/3E+3x2,5 St

Monitoring equipment Thermal contacts opening temperature

140° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

O-rings

Nitrile rubber

Shaft

L 3201

Alternative

Material

1

Carbon steel

2

Stainless steel

Product

Mechanical face seals

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Alternative

Inner seal

Outer seal

1

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Denomination Product code Installation Impeller characteristic

3201.180

Surface Treatment

L

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

LT

Process data Liquid temperature

Weight max +40° C

Depth of immersion

max 20 m

The pH of the pumped liquid

pH 5,5-14

Liquid density Impeller throughlet

max. 1100 kg/m

See dimensional drawing.

Option

3

See Motor rating table

Insulation class

60 Hz H (+180° C)

- intermittent running Voltage imbalance between phases No. of starts/hour

Leakage sensor in stator housing

FLS

Leakage sensor in oil housing

CLS

Surface treatment max ± 5%

Epoxy treatment

Zinc anodes

max ± 10%

Accessories

max 2% max 30

Electrical accessories such as pump controller, control panels, starters, monitoring relays.

Cable

See separate booklet or www.flygt.com, for further information.

Direct-on-line start SUBCAB®

Industrial version

Other cables

Voltage variation - continuously running

Ex. proof version

3201.980 Warm liquid version on request

Motor data Frequency

3201.091

4G10+2x1,5 mm2 4G16+2x1,5 mm2 4G25 mm2 4G25+2x1,5 mm2

2

L 3201

P2 [kW] / [hp]

Ex proof version available

Impeller thoughlet, mm

Power factor cos ϕ

Starting current, A

Rated current, A

Rated power, kW

Curve/Impeller No

LT - Motor rating and performance curve 35 30 25 20 15

22,0

41,0

20 16 821

12

823 822 825

824

H [m] / [ft]

460 V, 60 Hz, 3 ~, 860 r/min 821

24

45 164

0,80

102

LT

Yes

822

22,0

41,0

164

0,80

102

823

22,0

41,0

164

0,80

102

Yes

824

22,0

41,0

164

0,80

102

Yes

825

22,0

41,0

164

0,80

102

Yes

40

Yes

12

35 10 30 25

Y/D starting current is approximately 1/3 of D starting current.

20 15

8 6 4

10 5 0

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

3

2 823 825

0

822 824

821

0

50 100 150 200 250 300 350 400

0

1000 2000 3000 4000 5000 6000 7000 Q [l/s] / [usgpm]

L3201.60Hz.04.01.EN.FIN.12.04 © ITT Flygt AB

www.flygt.com

895225

Technical specification Submersible pump L 3201, 60 Hz

L 3201 SUBCAB®

4G35 mm2 4G35+2x1,5 mm2

Y/D start SUBCAB®

7G6+2x1,5 mm2

VFD Application NSSHÖU../3E+St

3x16+3x16/3E+3x2,5 St

Monitoring equipment Thermal contacts opening temperature

140° C

Material Impeller

Cast iron

Diffusor

Cast iron

Stator housing

Cast iron

O-rings

Nitrile rubber

Shaft

L 3201

Alternative

Material

1

Carbon steel

2

Stainless steel

Product

Mechanical face seals

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Alternative

Inner seal

Outer seal

1

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Denomination Product code Installation Impeller characteristic

3201.180

Surface Treatment

L

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

LT

Process data Liquid temperature

Weight max +40° C

Depth of immersion

max 20 m

The pH of the pumped liquid

pH 5,5-14

Liquid density Impeller throughlet

max. 1100 kg/m

See dimensional drawing.

Option

3

See Motor rating table

Insulation class

60 Hz H (+180° C)

- intermittent running Voltage imbalance between phases No. of starts/hour

Leakage sensor in stator housing

FLS

Leakage sensor in oil housing

CLS

Surface treatment max ± 5%

Epoxy treatment

Zinc anodes

max ± 10%

Accessories

max 2% max 30

Electrical accessories such as pump controller, control panels, starters, monitoring relays.

Cable

See separate booklet or www.flygt.com, for further information.

Direct-on-line start SUBCAB®

Industrial version

Other cables

Voltage variation - continuously running

Ex. proof version

3201.980 Warm liquid version on request

Motor data Frequency

3201.091

4G10+2x1,5 mm2 4G16+2x1,5 mm2 4G25 mm2 4G25+2x1,5 mm2

2

L 3201

P2 [kW] / [hp]

Ex proof version available

Impeller thoughlet, mm

Power factor cos ϕ

Starting current, A

Rated current, A

Rated power, kW

Curve/Impeller No

LT - Motor rating and performance curve 35 30 25 20 15

22,0

41,0

20 16 821

12

823 822 825

824

H [m] / [ft]

460 V, 60 Hz, 3 ~, 860 r/min 821

24

45 164

0,80

102

LT

Yes

822

22,0

41,0

164

0,80

102

823

22,0

41,0

164

0,80

102

Yes

824

22,0

41,0

164

0,80

102

Yes

825

22,0

41,0

164

0,80

102

Yes

40

Yes

12

35 10 30 25

Y/D starting current is approximately 1/3 of D starting current.

20 15

8 6 4

10 5 0

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

3

2 823 825

0

822 824

821

0

50 100 150 200 250 300 350 400

0

1000 2000 3000 4000 5000 6000 7000 Q [l/s] / [usgpm]

L3201.60Hz.04.01.EN.FIN.12.04 © ITT Flygt AB

www.flygt.com

895225

Technical specification Submersible pump L 3300, 60 Hz

L 3300 SUBCAB®

4G10+2x1,5 mm2 4G16+2x1,5 mm2 4G25+2x1,5 mm2 4G35+2x1,5 mm2

3300/6XX SUBCAB®

To be dimensioned by ITT Flygt

Y/D start 3300.181 SUBCAB®

2x4G10+2x1,5 mm2 2x4G16+2x1,5 mm2 2x4G25+2x1,5 mm2 2x4G35+2x1,5 mm2

3300/6XX SUBCAB®

To be dimensioned by ITT Flygt

VFD Application NSSHÖU../3E+St

3x35+3x16/3E+3x2,5 St

Monitoring equipment

L 3300

Thermal contacts opening temperature

140° C

Material

Product

Impeller

Cast iron

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Diffusor

Cast iron

Denomination

O-rings

Product code Installation Impeller characteristic

Stator housing

Shaft

3300.181 L LT

Process data Liquid temperature Depth of immersion The pH of the pumped liquid Liquid density Impeller throughlet

Insulation class

max 20 m

- intermittent running Voltage imbalance between phases No. of starts/hour

Material

1

Carbon steel

2

Stainless steel

Alternative

Inner seal

Outer seal

1

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

pH 5,5-14 max. 1100 kg/m3 See Motor rating table

Surface Treatment All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

60 Hz H (+180° C)

Weight

Voltage variation - continuously running

Alternative

Mechanical face seals max +40° C

Motor data Frequency

Cast iron Nitrile rubber

max ± 5%

See dimensional drawing.

max ± 10%

Option

max 2% max 30

3300.091

Cable Direct-on-line start

Ex. proof version

Leakage sensor in stator housing

FLS

Leakage sensor in oil housing

CLS

Other cables Surface treatment

3300.181

Zinc anodes

3

Epoxy treatment

L 3300 Accessories Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information.

LT - Motor rating and performance curve

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

60,0

279

0,82

102

Yes

808

34,0

60,0

279

0,82

102

No

809

34,0

60,0

279

0,82

102

Yes

Rated current, A

34,0

Rated power, kW

807

Curve/Impeller No

Starting current, A

Impeller L

P2 [kW] / [hp]

80 50 60 40 40

30

804

20 20

809

808

805 806 807

H [m] / [ft]

460 V, 60 Hz, 3 ~, 875 r/min

LT 50

14

460 V, 60 Hz, 3 ~, 875 r/min

40

804

45,0

80,0

360

0,82

102

Yes

805

45,0

80,0

360

0,82

102

Yes

806

45,0

80,0

360

0,82

102

Yes

807

45,0

80,0

360

0,82

102

Yes

808

45,0

80,0

360

0,82

102

Yes

809

45,0

80,0

360

0,82

102

Yes

16

12 10

30 8 20

6 4

10

Y/D starting current is approximately 1/3 of D starting current.

2 0

805 804 807 806 809808

0 0 0

100 2000

200

300

4000

400 6000

500 8000

600 10000

Q [l/s] / [usgpm]

4

L 3300 LT - Motor rating and performance curve 3300.180, Impeller NL

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

60,0

279

0,82

90

Yes

822

34,0

60,0

279

0,82

90

Yes

Rated current, A

34,0

Rated power, kW

821

Curve/Impeller No

Starting current, A

P [hp] / [kW] 90 80 70 60 50

60 623

50 40

624 821

40

30

30

20

822 823 824

H [ft] / [m]

460 V, 60 Hz, 3 ~, 875 r/min

823

34,0

60,0

279

0,82

90

Yes

824

34,0

60,0

279

0,82

90

Yes

LT 80

25

20 60

460 V, 60 Hz, 3 ~, 875 r/min

15

624

45,0

80,0

360

0,82

90

Yes

821

45,0

80,0

360

0,82

90

Yes

822

45,0

80,0

360

0,82

90

Yes

823

45,0

80,0

360

0,82

90

Yes

824

45,0

80,0

360

0,82

90

Yes

40

10

20

5

460 V, 60 Hz, 3 ~, 1170 r/min 623

56,0

90,0

510

0,89

90

Yes

624

56,0

90,0

510

0,89

90

Yes

0

824

0 0

Y/D starting current is approximately 1/3 of D starting current.

0

5

100

2000

200

300

4000

400

6000

821 822 823

623 624

500

8000 Q [l/s] / [usgpm]

L 3300 Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

LT, L-installation

LT, L-installation

6

L3300.60Hz.04.01.Eng.01.08 © ITT Flygt AB

www.flygt.com

895231

Technical specification Submersible pump L 3300, 60 Hz

L 3300 SUBCAB®

4G10+2x1,5 mm2 4G16+2x1,5 mm2 4G25+2x1,5 mm2 4G35+2x1,5 mm2

3300/6XX SUBCAB®

To be dimensioned by ITT Flygt

Y/D start 3300.181 SUBCAB®

2x4G10+2x1,5 mm2 2x4G16+2x1,5 mm2 2x4G25+2x1,5 mm2 2x4G35+2x1,5 mm2

3300/6XX SUBCAB®

To be dimensioned by ITT Flygt

VFD Application NSSHÖU../3E+St

3x35+3x16/3E+3x2,5 St

Monitoring equipment

L 3300

Thermal contacts opening temperature

140° C

Material

Product

Impeller

Cast iron

Submersible pump for pumping clean, surface or waste water containing fibre-free solids.

Diffusor

Cast iron

Denomination

O-rings

Product code Installation Impeller characteristic

Stator housing

Shaft

3300.181 L LT

Process data Liquid temperature Depth of immersion The pH of the pumped liquid Liquid density Impeller throughlet

Insulation class

max 20 m

- intermittent running Voltage imbalance between phases No. of starts/hour

Material

1

Carbon steel

2

Stainless steel

Alternative

Inner seal

Outer seal

1

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

pH 5,5-14 max. 1100 kg/m3 See Motor rating table

Surface Treatment All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

60 Hz H (+180° C)

Weight

Voltage variation - continuously running

Alternative

Mechanical face seals max +40° C

Motor data Frequency

Cast iron Nitrile rubber

max ± 5%

See dimensional drawing.

max ± 10%

Option

max 2% max 30

3300.091

Cable Direct-on-line start

Ex. proof version

Leakage sensor in stator housing

FLS

Leakage sensor in oil housing

CLS

Other cables Surface treatment

3300.181

Zinc anodes

3

Epoxy treatment

L 3300 Accessories Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information.

LT - Motor rating and performance curve

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

60,0

279

0,82

102

Yes

808

34,0

60,0

279

0,82

102

No

809

34,0

60,0

279

0,82

102

Yes

Rated current, A

34,0

Rated power, kW

807

Curve/Impeller No

Starting current, A

Impeller L

P2 [kW] / [hp]

80 50 60 40 40

30

804

20 20

809

808

805 806 807

H [m] / [ft]

460 V, 60 Hz, 3 ~, 875 r/min

LT 50

14

460 V, 60 Hz, 3 ~, 875 r/min

40

804

45,0

80,0

360

0,82

102

Yes

805

45,0

80,0

360

0,82

102

Yes

806

45,0

80,0

360

0,82

102

Yes

807

45,0

80,0

360

0,82

102

Yes

808

45,0

80,0

360

0,82

102

Yes

809

45,0

80,0

360

0,82

102

Yes

16

12 10

30 8 20

6 4

10

Y/D starting current is approximately 1/3 of D starting current.

2 0

805 804 807 806 809808

0 0 0

100 2000

200

300

4000

400 6000

500 8000

600 10000

Q [l/s] / [usgpm]

4

L 3300 LT - Motor rating and performance curve 3300.180, Impeller NL

Power factor cos ϕ

Impeller thoughlet, mm

Ex proof version available

60,0

279

0,82

90

Yes

822

34,0

60,0

279

0,82

90

Yes

Rated current, A

34,0

Rated power, kW

821

Curve/Impeller No

Starting current, A

P [hp] / [kW] 90 80 70 60 50

60 623

50 40

624 821

40

30

30

20

822 823 824

H [ft] / [m]

460 V, 60 Hz, 3 ~, 875 r/min

823

34,0

60,0

279

0,82

90

Yes

824

34,0

60,0

279

0,82

90

Yes

LT 80

25

20 60

460 V, 60 Hz, 3 ~, 875 r/min

15

624

45,0

80,0

360

0,82

90

Yes

821

45,0

80,0

360

0,82

90

Yes

822

45,0

80,0

360

0,82

90

Yes

823

45,0

80,0

360

0,82

90

Yes

824

45,0

80,0

360

0,82

90

Yes

40

10

20

5

460 V, 60 Hz, 3 ~, 1170 r/min 623

56,0

90,0

510

0,89

90

Yes

624

56,0

90,0

510

0,89

90

Yes

0

824

0 0

Y/D starting current is approximately 1/3 of D starting current.

0

5

100

2000

200

300

4000

400

6000

821 822 823

623 624

500

8000 Q [l/s] / [usgpm]

L 3300 Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

LT, L-installation

LT, L-installation

6

L3300.60Hz.04.01.Eng.01.08 © ITT Flygt AB

www.flygt.com

895231

Technical specification Submersible pump L 3356, 60 Hz

L 3356 Monitoring equipment Thermal contacts opening temperature

140° C

Leakage sensor in junction box

FLS

Analogue temperature sensor in main bearing

Pt100

Leakage sensor in stator housing Drive unit Sensor 6XX

FLS

7XX

Ball float switch

Material Pump housing

Cast iron

Stator housing

Cast iron

O-rings

Nitrile rubber

Mechanical face seals Alternative

Inner seal

Outer seal

L 3356

1

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Corrosion resistant cemented carbide/ Corrosion resistant cemented carbide

Product

Impeller Alternative

Material

Submersible pump for pumping waste water containing minimum solids and short fibres in suspension. The pump can also be used for pumping raw-water.

1

Cast iron

2

Stainless steel

Shaft

Denomination

Alternative

Material

Product code

3356/605

1

Steel

Product code

3356/665

2

Stainless steel

Product code

3356/705

Surface Treatment

Product code

3356/735

Product code

3356/765

All cast parts are primed with a water-borne primer. The finishing coat is a high-solid two pack paint.

Installation

Weight

L

Process data Liquid temperature Depth of immersion The pH of the pumped liquid Liquid density Impeller throughlet

See dimensional drawing.

Option

max +40° C max 20 m

3356/675

Ex. proof version

pH 6 - 11

3356/715

Ex. proof version

max. 1100 kg/m3

3356/745

Ex. proof version

See Motor rating table

3356/775

Ex. proof version

Leakage sensor in oil housing

Motor data Frequency Insulation class

60 Hz H (+180° C)

- intermittent running Voltage imbalance between phases No. of starts/hour

Pt100

Analogue temperature sensor in support bearing

Pt100

Surface treatment max ± 5%

Epoxy treatment

Zinc anodes

max ± 10%

Accessories

max 2%

Discharge connections, adapters, hose connections and other mechanical accessories.

max 15

Cable SUBCAB®

Analogue temperature sensor in stator Other cables

Voltage variation - continuously running

CLS

Electrical accessories such as pump controller, control panels, starters, monitoring relays. See separate booklet or www.flygt.com, for further information.

To be dimensioned by ITT Flygt

3

L 3356

ft

Ex proof version available

Impeller throughlet, mm

Power factor cos ϕ

Starting current, A

Rated current, A

Rated power, kW

Drive unit

Curve/Impeller No

Motor rating and performance curve

40

120

36

100

810

605

52,0

92,0

440

0,79

102

No

665

63,0

111

550

0,79

102

Yes

810

665

75,0

128

660

0,80

102

Yes

810

705

101

173

790

0,81

102

Yes

28

80

24

70

16

40

12

20 10 0

610

20

50 30

460 V, 60 Hz, 3 ~, 1185 r/min

32

90

60

810

m

130 110

460 V, 60 Hz, 3 ~, 880 r/min

H

810

8 4 0

610

665

104

179

1195

0,79

102

Yes

610

705

127

212

1155

0,81

102

Yes

0

2000

610

735

179

288

1555

0,84

102

Yes

610

765

231

380

2230

0,81

102

Yes

200

300

4000

400 6000

500 8000

600

10000

Y/D starting current is approximately 1/3 of D starting current.

Dimensional drawing All drawings are available as Acrobat documents (.pdf) and AutoCad drawings (.dwg). Download the drawings from www.flygt.com or contact your ITT Flygt representative for more information. All dimensions are in mm.

Drive unit 605/615, L-installation

Drive unit 665/675, L-installation

4

l/s Q 12000 USgpm

700

800

L 3356 Drive unit 705/715, L-installation

Drive unit 735/745, L-installation

Drive unit 765/775, L-installation

5

L 3356

6

L3356.60Hz.04.01.EN.FIN.01.05 © ITT Flygt AB

www.flygt.com

895288