VULKARDAN E
Technische Daten / technical data
02
Gültigkeitsklausel
Validity Clause
Die vorliegende Broschüre ersetzt alle vorherigen Ausgaben, ältere Drucke verlieren ihre Gültigkeit. VULKAN ist berechtigt, aufgrund neuerer Entwicklungen die in dieser Broschüre enthaltenen Daten entsprechend anzupassen und zu verändern. Die neuen Daten gelten nur für nach der Änderung bestellte Kupplungen. Es liegt im Verantwortungsbereich des Anwenders dafür zu sorgen, dass ausschließlich die aktuelle Katalogversion verwendet wird. Der jeweils aktuelle Stand ist auf der Webseite von VULKAN unter www.vulkan.com jederzeit abrufbar.
The present catalogue shall replace all previous editions, any previous printings shall no longer be valid. Based on new developments, VULKAN reserves the right to amend and change any details contained in this catalogue respectively. The new data shall only apply with respect to couplings that were ordered after said amendment or change. It shall be the responsibility of the user to ensure that only the latest catalogue issue will be used. The respective latest issue can be seen on the website of VULKAN on www.vulkan.com.
Die Angaben in dieser Broschüre beziehen sich auf den technischen Standard gültig im Hause VULKAN und stehen unter den in den Erläuterungen definierten Bedingungen. Es liegt allein im Entscheidungs- und Verantwortungsrahmen des Systemverantwort-lichen für die Antriebslinie, entsprechende Rückschlüsse auf das Systemverhalten zu ziehen.
The data contained in this catalogue refer to the technical standard as presently used by VULKAN with defined conditions according to the explanations. It shall be the sole responsibility and decision of the system administrator for the drive line to draw conclusions about the system behaviour.
VULKAN Drehschwingungsanalysen berücksichtigen in der Regel nur das rein mechanische Schwingungsersatzsystem. Als reiner Komponentenhersteller übernimmt VULKAN mit der Analyse des Drehschwingungssystems (stationär, transient) nicht die Systemverantwortung! Die Genauigkeit der Analyse hängt von der Genauigkeit der verwendeten bzw. der VULKAN zur Verfügung gestellten Daten ab.
VULKAN torsional vibration analysis usually only consider the pure mechanical mass-elastic system. Being a component manufacturer exclusively, VULKAN assumes no system responsibility with the analysis of the torsional vibration system (stationary, transiently)! The accuracy of the analysis depends on the exactness of the used data and the data VULKAN is provided with, respectively.
Änderungen aufgrund des technischen Fortschritts sind vorbehalten. Bei Unklarheiten bzw. Rückfragen kontaktieren Sie bitte VULKAN.
Any changes due to the technological progress are reserved. For questions or queries please contact VULKAN.
Stand 01/2011 Das Recht auf Vervielfältigung, Nachdruck und Übersetzungen behalten wir uns vor. Maß- und Konstruktionsänderungen vorbehalten.
Status: 01/2011 All duplication, reprinting and translation rights are reserved. We reserve the right to modify dimensions and constructions without prior notice.
VULKARDAN E
Inhaltsverzeichnis CONTENTS 02
Gültigkeitsklausel Validity Clause
03
Inhaltsverzeichnis CONTeNTS
04
EigEnschaftEn und BEschrEiBung CharaCteristiCs and desCription
06
ListE dEr tEchnischEn datEn lisT Of Technical DaTa
09
13
06
Geglockte Anwendung ( VULKARDAN E – Ausführung: Gummi) Bell Housing Application ( VULKARDAN E – Execution: Rubber)
07
Freistehende Anwendung ( VULKARDAN E – Ausführung: Gummi) Free Standing Application ( VULKARDAN E – Execution: Rubber)
08
Geglockte Anwendung ( VULKARDAN E – Ausführung: Silikon) Bell Housing Application ( VULKARDAN E – Execution: Silicone)
08
Freistehende Anwendung ( VULKARDAN E – Ausführung: Silikon) Free Standing Application ( VULKARDAN E – Execution: Silicone)
Abmessungen/Massenträgheitsmomente/Massen Dimensions/Mass-Moments of Inertia/Masses 09
VULKARDAN E Baureihe 4000/4001 / Series 4000/4001
10
VULKARDAN E Baureihe 4110 / Series 4110
11
VULKARDAN E Baureihe 4111 / Series 4111
12
VULKARDAN E Baureihe 4400 / Series 4400
wEitErE ausführungEn further exeCutions
VULKARDAN E
03
Eigenschaften und Beschreibung Characteristics and Description
VULKARDAN E Kupplungen / VULKARDAN E Couplings Drehmoment: 0,16 – 20,00 kNm / Torque range: 0.16 – 20.00 kNm
04
VULKARDAN E
Hochelastische VULKARDAN E Kupplungen
Highly Flexible VULKARDAN E Couplings
Die hochelastische VULKARDAN E Kupplung wurde für Antriebe im Drehmomentbereich TKN 0,16 – 20,0 kNm entwickelt.
The highly flexible VULKARDAN E coupling has been developed for drives with a torque range TKN 0.16 – 20,0 kNm.
Die VULKARDAN E Kupplung ist eine hochelastische Gummikupplung mit linearer Drehfederkennlinie. Zur Abstimmung auf die entsprechenden Anlagenanforderungen stehen 4 Gummiqualitäten zur Verfügung. Alternativ sind Elemente in Silikon mit einer progressiven Drehfederkennlinie lieferbar.
The VULKARDAN E coupling is a highly flexible rubber coupling with a linear stiffness characteristic. Four rubber qualities are available in order to tune the coupling to the various system requirements. As an alternative elements in silicone with a progressive stiffness characteristic are available.
Die VULKARDAN E - Elemente sind aus wärmebeständigem Gummi. Die zulässigen Umgebungstemperaturen liegen bei -45°C bis +90°C. Alternativ sind für Umgebungstemperaturen von -45°C bis +120°C Elemente in Silikon lieferbar. Im Interesse einer hohen Lebensdauer, sollte jedoch auch auf ausreichende Belüftungsquerschnitte geachtet werden. Dies gilt besonders bei Flanschglockeneinbauten. Die gegebenen technischen Daten stellen Maximalwerte dar, die nicht zeitgleich auftreten dürfen. Die wechselseitige Beeinflussung von Betriebszuständen führt zu einer Reduktion dieser Werte und muss bei der Kupplungsauslegung berücksichtigt werden.
The VULKARDAN E elements are made from more heat-resistant rubber. The permissible ambient temperatures range are from -45°C to +90°C. As an alternative, elements in silicone are available for an ambient temperature range from -45°C to +120°C. With respect to a long lifetime, however, consideration should be given to sufficiently large ventilation cross sections. This is very important when considering flange bellhousings. The given data represent maximum values which may not arise at the same time. The mutual influence of operating conditions leads to a reduction of these values and must be considered during the coupling selection.
Die hochelastische VULKARDAN E Kupplung wird verwendet, um das Drehschwingungsverhalten der Anlage optimal abzustimmen. Durch ihre steckbare Ausführung findet sie vornehmlich Verwendung in sog. Glockeneinbauten.
The highly flexible VULKARDAN E coupling is used to tune the torsional response of the system. It is a coupling with „slip-on“ feature and therefore is used mainly in bellhousing installations.
Die hochelastische VULKARDAN E Kupplung in freistehender Ausführung findet Verwendung zur Verbindung von elastisch/starr aufgestellten Motoren mit Getrieben oder anderen Arbeitsmaschinen. Sie ergänzt die RATO Kupplung im unteren Drehmomentbereich.
The highly flexible VULKARDAN E free-standing coupling is used to connect flexible/ rigidly mounted engines with gearboxes or other machineries. It completes the RATO coupling in the lower torque range.
Die besonderen Eigenschaften der VULKARDAN E Kupplung in freistehender Ausführung sind – winkel- und radialverlagerungsfähig – axial ausgleichend – drehelastisch und dämpfend – geräuschdämmend – radial ausbaubar Die Einbauabmessungen entsprechen den SAE Standards.
The special features of the VULKARDAN E free-standing coupling are – angular and radial misalignment capacity – compensates axial misalignment – torsionally highly flexible with damping – noise attenuating properties – radial disassembly The installation dimensions correspond to SAE standards.
0.16
2.5
5.0
20.0
0.16
2.5
5.0
20.0
VULKARDAN E Bellhousing installation
VULKARDAN E free-standing
VULKARDAN E Connection Shaft-Shaft
Das Recht auf Vervielfältigungen, Nachdruck und Übersetzungen behalten wir uns vor. Maß- und Konstruktionsänderungen vorbehalten.
All rights of duplication, reprinting and translation are reserved. We reserve the right to modify dimensions and constructions without prior notice.
VULKARDAN E
05
Liste der Technischen Daten (geglockte anwendung) List of Technical Data (Bell housing application)
VULKARDAN E Kupplung – Ausführung: Gummi / VULKARDAN E Coupling – Execution: Rubber Baugröße
Baugruppe
Zulässige Drehmomentgröße NennMax. Max. drehmoment Drehmoment1 Drehmoment2
Size
1714 1711 1715 1712 2314 2311 2315 2312 2424 2411 2415 2412 2814 2811 2815 2812 3214 3211 3215 3212 3414 3411 3415 3412 4014 4011 4015 4012 4914 4911 4915 4912
Dimension Group
1710
2310
2410
2810
3210
3410
4010
4910
Max. Drehmomentbereich
Zul. Wechseldrehmoment
Permissible Torque Values Norminal Torque
Max. Torque
Max. Torque
Max. Torque Range
Perm. Vibratory Torque
TKN kNm
TKmax1 kNm
TKmax2 kNm
∆Tmax kNm
TKW kNm
0,16 0,16 0,20 0,20 0,55 0,55 0,68 0,68 0,63 0,63 0,80 0,80 1,00 1,00 1,25 1,25 1,25 1,25 1,50 1,50 1,60 1,60 2,00 2,00 2,50 2,50 3,15 3,15 4,00 4,00 5,00 5,00
0,24 0,24 0,30 0,30 0,83 0,83 1,02 1,02 0,95 0,95 1,20 1,20 1,50 1,50 1,88 1,88 1,88 1,88 2,25 2,25 2,40 2,40 3,00 3,00 3,75 3,75 4,73 4,73 6,00 6,00 7,50 7,50
0,58 0,58 0,72 0,72 1,98 1,98 2,45 2,45 2,27 2,27 2,88 2,88 3,60 3,60 4,50 4,50 4,50 4,50 5,40 5,40 5,76 5,76 7,20 7,20 9,00 9,00 11,34 11,34 14,40 14,40 18,00 18,00
0,17 0,26 0,34 0,42 0,54 0,82 1,09 1,35 0,62 0,94 1,25 1,55 0,98 1,49 1,97 2,45 1,14 1,74 2,30 2,86 1,58 2,41 3,19 3,96 2,45 3,72 4,93 6,12 4,31 6,55 8,68 10,79
Zul. Verlustleistung
Zul. Drehzahl
Zul. radialer Kupplungsversatz
Radiale Federsteife
Dynamische Drehfedersteife
Verhältnismäßige Dämpfung
Perm. Power Loss
Perm. Rotational Speed
Perm. Radial Coupling Displacement
Radial Stiffness
Dynamic Torsional Stiffness
Relative Damping
PKV50;1h kW
nKmax 1/min
∆K r‘ 2) mm
C rdyn kN/mm
C Tdyn1) 2) kNm/ rad
ψ 1) 3)
3,6 3,6 2,1 1,5 2,7 2,7 1,4 1,0 2,0 2,0 1,2 0,8 2,4 2,4 1,4 1,0 3,2 3,2 1,6 1,1 4,4 4,4 2,2 1,6 5,9 5,9 3,1 2,3 8,2 8,2 4,8 3,5
0,15 0,19 0,33 0,45 0,40 0,52 1,02 1,41 0,56 0,75 1,29 1,79 0,64 0,86 1,47 2,04 0,57 0,74 1,52 2,10 0,51 0,70 1,34 1,85 0,51 0,70 1,34 1,85 0,52 0,69 1,18 1,64
0,65 0,85 1,45 2,00 1,75 2,30 4,50 6,20 2,60 3,50 6,00 8,30 4,10 5,50 9,40 13,00 4,20 5,50 11,30 15,60 5,40 7,50 14,70 20,50 8,00 11,00 21,00 29,00 16,50 22,00 37,50 52,00
0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13
0,06
0,147
7500
0,22
0,173
6300
0,25
0,248
6000
0,40
0,287
5100
0,50
0,259
4900
0,64
0,333
4250
1,00
0,337
3600
1,60
0,440
2750
Siehe Erläuterung der Technischen Daten 1) VULKAN empfiehlt die zusätzliche Berücksichtigung von CTdyn warm (0,7), CTdyn la (1,35) und ψ warm (0,7) für die Berechnung der Drehschwingungen in der Anlage. 2) Der Betriebszustand der Anlage kann eine Korrektur der gegebenen Werte notwendig machen. Siehe Erläuterunge der Technischen Daten. Bei mehrreihigen Kupplungen müssen bei der Drehschwingungsanalyse der Anlage die
See Explanation of the Technical Data 1) VULKAN recommends additionally taking into account CTdyn warm (0,7), CTdyn la (1,35) and ψ warm (0,7) for calculating the torsional vibration in the system. 2) The operating state of the system can make it necessary to correct the values given. See technical data notes. With multi-row couplings, the individual moments of inertia of the coupling and the
individuellen Massenträgheitsmomente der Kupplung und die dynamischen Drehfederstei-
dynamic torsional stiffnesses of the individual elements must be taken into account during
fen der einzelnen Elemente berücksichtigt werden.
the torsional vibration analysis of the system.
Durch die Eigenschaft des Werkstoffs Gummi sind Toleranzen der aufgeführten Daten für
The properties of the rubber material mean that tolerances of + 30 % to 0 % for the 4
CTdyn von + 30 % bis 0 % für die 4er Elemente bzw. von +10 % bis - 20 % für die 1er und
elements and + 10 % to - 20 % for the 1 and silicone elements, and + 20 % to -10 % for the 5/2
Silicon-Elemente bzw. von + 20 % bis - 10 % für die 5/2er Elemente möglich.
3) Bedingt durch die physikalischen Eigenschaften der elastischen Elemente sind Toleranzen der aufgeführten Daten für ψ, von 10 % bis - 20 % für die 4, 1, 5, 2 Silicon-Elemente möglich.
06
VULKARDAN E
elements with respect to the data given for CTdyn are possible.
3) Because of the physical properties of the elastic elements, tolerances of 10 % to - 20 % for the 4, 1, 5, 2 silicone elements with respect to the data given for ψ are possible.
LTD-2
Liste der Technischen Daten (freistehende anwendung) List of Technical Data (free standing application)
VULKARDAN E Kupplung – Ausführung: Gummi / VULKARDAN E Coupling – Execution: Rubber Baugröße
Size
4014 4011 4015 4012 4114 4111 4115 4112 4814 4811 4815 4812 4914 4911 4915 4912 5414 5411 5415 5412 5714 5711 5715 5712 6014 6011 6015 6012
Baugruppe
Dimension Group
4010
4110
4810
4910
5410
5710
6010
Zulässige Drehmomentgröße Nenndrehmoment
Max. Drehmoment1
Norminal Torque
Max. Torque
Max. Torque
TKN kNm
TKmax1 kNm
TKmax2 kNm
∆Tmax kNm
2,50 2,50 3,15 3,15 2,50 2,50 3,15 3,15 4,00 4,00 5,00 5,00 4,00 4,00 5,00 5,00 6,30 6,30 8,00 8,00 10,00 10,00 12,50 12,50 16,00 16,00 20,00 20,00
3,75 3,75 4,73 4,73 3,75 3,75 4,65 4,65 6,00 6,00 7,50 7,50 6,00 6,00 7,50 7,50 9,45 9,45 12,00 12,00 15,00 15,00 18,75 18,75 24,00 24,00 30,00 30,00
9,00 9,00 11,34 11,34 9,00 9,00 11,16 11,16 14,40 14,40 18,00 18,00 14,40 14,40 18,00 18,00 22,68 22,68 28,80 28,80 36,00 36,00 45,00 45,00 57,50 57,50 72,00 72,00
2,45 3,72 4,93 6,12 3,50 3,95 5,40 6,10 5,69 6,39 8,75 9,91 4,31 6,55 8,68 10,79 5,99 9,01 11,93 14,83 9,44 14,35 19,00 23,62 14,96 22,72 30,10 37,40
Max. Drehmoment2
Max. Drehmomentbereich
Zul. Wechseldrehmoment
Permissible Torque Values Max. Perm. VibraTorque Range tory Torque TKW kNm
Zul. Verlustleistung
Zul. Drehzahl
Radiale Dynamische Zul. radialer Zul. axialer Kupplungs- Wellenver- Federsteife Drehfedersteife satz versatz
Perm. Power Loss
Perm. Rotational Speed
Perm. Radial Perm. Axial Shaft DisCoupling Displacement placement
PKV50, 1h kW
nKmax 1/min
1,00
0,337
3600
1,00
0,640
2500
1,60
0,707
2300
1,60
0,440
2750
2,50
0,507
2300
4,00
0,520
2100
6,40
0,713
1900
∆K r‘ 2) mm 5,9 5,9 3,1 2,3 9,9 7,3 4,4 3,1 9,7 7,3 4,3 3,1 8,2 8,2 4,8 3,5 10,7 10,7 5,3 3,8 10,4 10,4 5,2 3,7 8,6 8,6 4,9 3,6
∆ K a mm
3,5
3,5
3,5
3,5 4,0 4,0 4,5* 4,5* 4,5
6,0
Verhältnismäßige Dämpfung
Radial Stiffness
Dynamic Torsional Stiffness
Relative Damping
C rdyn kN/mm
C Tdyn1) 2) kNm/rad
ψ 1) 3)
0,51 0,70 1,34 1,85 0,50 0,60 1,10 1,50 0,67 0,89 1,51 2,10 0,52 0,69 1,18 1,64 0,53 0,72 1,46 2,02 0,75 1,00 2,02 2,78 1,08 1,48 2,59 3,58
8,00 11,00 21,00 29,00 10,00 13,50 23,00 32,00 16,50 22,00 37,50 52,00 16,50 22,00 37,50 52,00 22,00 29,50 60,00 83,00 34,50 46,00 93,00 128,00 62,00 85,00 149,00 206,00
0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13 0,75 1,00 1,13 1,13
* Gilt für Baureihe 4400
*Valid for Series 4400
Siehe Erläuterung der Technischen Daten 1) VULKAN empfiehlt die zusätzliche Berücksichtigung von CTdyn warm (0,7), CTdyn la (1,35) und ψ warm (0,7) für die Berechnung der Drehschwingungen in der Anlage. 2) Der Betriebszustand der Anlage kann eine Korrektur der gegebenen Werte notwendig machen. Siehe Erläuterunge der Technischen Daten.
See Explanation of the Technical Data 1) VULKAN recommends additionally taking into account CTdyn warm (0,7), CTdyn la (1,35) and ψ warm (0,7) for calculating the torsional vibration in the system. 2) The operating state of the system can make it necessary to correct the values given. See technical data notes. With multi-row couplings, the individual moments of inertia of the coupling and the
Bei mehrreihigen Kupplungen müssen bei der Drehschwingungsanalyse der Anlage die individuellen Massenträgheitsmomente der Kupplung und die dynamischen Drehfederstei-
dynamic torsional stiffnesses of the individual elements must be taken into account during
fen der einzelnen Elemente berücksichtigt werden.
the torsional vibration analysis of the system.
Durch die Eigenschaft des Werkstoffs Gummi sind Toleranzen der aufgeführten Daten für
The properties of the rubber material mean that tolerances of + 30 % to 0 % for the 4
CTdyn von + 30 % bis 0 % für die 4er Elemente bzw. von +10 % bis - 20 % für die 1er und
elements and + 10 % to - 20 % for the 1 and silicone elements, and + 20 % to -10 % for the 5/2
Silicon-Elemente bzw. von + 20 % bis - 10 % für die 5/2er Elemente möglich.
3) Bedingt durch die physikalischen Eigenschaften der elastischen Elemente sind Toleranzen der aufgeführten Daten für ψ, von 10 % bis - 20 % für die 4, 1, 5, 2 Silicon-Elemente möglich.
LTD-2
elements with respect to the data given for CTdyn are possible.
3) Because of the physical properties of the elastic elements, tolerances of 10 % to - 20 % for the 4, 1, 5, 2 silicone elements with respect to the data given for ψ are possible.
VULKARDAN E
07
Liste der Technischen Daten (geglockte anwendung) List of Technical Data (Bell housing application)
VULKARDAN E Kupplung – Ausführung: Silikon / VULKARDAN E Coupling – Execution: Silicone Geglockte Anwendung / Bell Housing Application Baugröße Baugruppe
Zulässige Drehmomentgröße Max. Max. Nenndrehmo- Drehmo- Drehmoment ment ment
Size
2811S 3411S 4011S 4911S
Dimension Group
Max. Drehmomentbereich
Zul. Wechseldrehmoment
Zul. VerlustZul. Zul. radialer leistung Drehzahl Kupplungsversatz
Perm. Radial Radial Perm. Perm. Stiffness Power Loss Rotational Coupling Speed Displacement
Permissible Torque Values
2810 3410 4010 4910
Radiale Federsteife
Max. Perm. VibraTorque Range tory Torque
Dynamische Drehfedersteife 10 % TKN
25 % TKN
50 % TKN
75 % TKN
100 % TKN
Dynamic Torsional Stiffness
Verhältnismäßige Dämpfung Relative Damping
Norminal Torque
Max. Torque
Max. Torque
TKN kNm
TKmax1 kNm
TKmax2 kNm
∆Tmax kNm
TKW kNm
PKV50;1h kW
nKmax 1/min
∆K r‘ 2) mm
C rdyn kN/mm
CTdyn1) 2) kNm/rad
ψ 1) 3)
1,25 2,00 3,15 5,00
1,75 2,80 4,41 7,00
2,50 4,00 6,30 10,00
1,54 2,50 3,86 6,80
0,40 0,64 1,00 1,60
0,450 0,550 0,550 0,733
5100 4250 3600 2750
1,9 2,8 3,3 5,3
1,10 1,12 1,27 1,07
4,40 4,60 4,70 7,00 10,50 6,90 7,00 8,10 11,80 17,60 10,00 11,00 13,20 20,00 32,00 19,40 19,90 23,10 33,90 47,00
1,13 1,13 1,13 1,13
10% TKN
25% TKN
50% TKN
75% TKN
100% TKN
VULKARDAN E Kupplung – Ausführung: Silikon / VULKARDAN E Coupling – Execution: Silicone Freistehende Anwendung / Free Standing Application Baugröße Baugruppe
Size
4011S 4911S 5411S 5711S 6011S
Dimension Group
4010 4910 5410 5710 6010
Zulässige Drehmomentgröße
Zul. VerlustZul. Zul. radialer Zul. axialer leistung Drehzahl Kupplungs- Wellenversatz versatz
Radiale Federsteife
Perm. Perm. Perm. Radial Perm. Axial Shaft DisPower Loss Rotational Coupling Displace- placement Speed ment
Radial Stiffness
Nenndrehmoment
Max. Drehmoment1
Norminal Torque
Max. Torque
Max. Torque
Max. Torque Range
Perm. Vibratory Torque
TKN kNm
TKmax1 kNm
TKmax2 kNm
∆Tmax kNm
TKW kNm
PKV50, 1h kW
nKmax 1/min
∆K r‘ 2) mm
3,15 5,00 8,00 12,50 20,00
4,41 7,00 11,20 17,50 28,00
6,30 10,00 16,00 25,00 40,00
3,86 6,80 9,35 14,89 23,59
1,00 1,60 2,50 4,00 6,40
0,550 0,733 0,833 0,867 1,200
3600 2750 2300 2100 1900
3,3 5,3 5,9 5,7 4,9
Max. Drehmoment2
Max. Drehmomentbereich
Zul. Wechseldrehmoment
Permissible Torque Values
∆ K a mm 3,5 3,5 4,0/4,5* 4,5 6,0
Dynamische Drehfedersteife 10 % TKN
25 % TKN
75 % TKN
Verhältnismäßige 100 % Dämpfung TKN
Dynamic Torsional Stiffness 10% TKN
25% TKN
Crdyn kN/mm 1,27 1,07 1,30 1,82 1,46
50 % TKN
10,00 19,40 30,90 48,20 70,00
11,00 19,90 35,40 55,20 75,90
50% TKN
75% TKN
100% TKN
Relative Damping
C Tdyn1) 2) kNm/rad
ψ 1) 3)
13,20 20,00 32,00 23,10 33,90 47,00 42,80 53,60 65,50 66,80 83,70 102,20 93,60 150,90 251,00
1,13 1,13 1,13 1,13 1,13
* Gilt für Baureihe 4400
*Valid for Series 4400
Siehe Erläuterung der Technischen Daten 1) VULKAN empfiehlt die zusätzliche Berücksichtigung von CTdyn warm (0,7), CTdyn la (1,35) und ψ warm (0,7) für die Berechnung der Drehschwingungen in der Anlage. 2) Der Betriebszustand der Anlage kann eine Korrektur der gegebenen Werte notwendig machen. Siehe Erläuterunge der Technischen Daten.
See Explanation of the Technical Data 1) VULKAN recommends additionally taking into account CTdyn warm (0,7), CTdyn la (1,35) and ψ warm (0,7) for calculating the torsional vibration in the system. 2) The operating state of the system can make it necessary to correct the values given. See technical data notes. With multi-row couplings, the individual moments of inertia of the coupling and the dynamic
Bei mehrreihigen Kupplungen müssen bei der Drehschwingungsanalyse der Anlage die individuellen Massenträgheitsmomente der Kupplung und die dynamischen Drehfedersteifen
torsional stiffnesses of the individual elements must be taken into account during the tor-
der einzelnen Elemente berücksichtigt werden.
sional vibration analysis of the system.
Durch die Eigenschaft des Werkstoffs Gummi sind Toleranzen der aufgeführten Daten für
The properties of the rubber material mean that tolerances of + 30 % to 0 % for the 4
CTdyn von + 30 % bis 0 % für die 4er Elemente bzw. von +10 % bis - 20 % für die 1er und
elements and + 10 % to - 20 % for the 1 and silicone elements, and + 20 % to -10 % for the 5/2
Silicon-Elemente bzw. von + 20 % bis - 10 % für die 5/2er Elemente möglich.
3) Bedingt durch die physikalischen Eigenschaften der elastischen Elemente sind Toleranzen der aufgeführten Daten für ψ, von 10 % bis - 20 % für die 4, 1, 5, 2 Silicon-Elemente möglich.
08
VULKARDAN E
elements with respect to the data given for CTdyn are possible.
3) Because of the physical properties of the elastic elements, tolerances of 10 % to - 20 % for the 4, 1, 5, 2 silicone elements with respect to the data given for ψ are possible.
LTD-2
Abmessungen/Massenträgheitsmomente/Massen Dimensions/Mass-Moments of Inertia/Masses VULKARDAN E Baureihe / Series 4000/4001 Baureihe / Series 4001 (mit Durchdrehsicherung * / with torsional limit device)
Baureihe / Series 4000
Baugruppe
Schwungrad nach SAE J620
Abmessungen
Massenträgheitsmoment
Masse
Dimension Group
flywheel
Dimensions
Mass moment of inertia
Mass
TKN
D 1
D 2
D 3
kNm 1710 2310
0,16 0,20 0,55 0,68
2410
0,63 0,80
2810
1,00 1,25
3210
1,25 1,50
3410 4010 4910
Maße in mm
A/M-4000-1
1,60 2,00 2,50 3,15 4,00 5,00
D 4
L kr
S 1
T
L 1
L 2
L 3
L 4
L 5
max 175,00 150,00 28,00
22,00 163,00
6,80
6
12,00
6 12
11 12 14
215,90 311,15 352,40 225,00 314,40 352,40 263,50 352,40 280,00 352,40 466,70
200,00 43,00 288,83 333,40 210,00 43,00 295,30 333,40 244,50 50,00 333,40 260,00 58,00 333,40 438,20
9,00 11,50 11,00 6,20 11,00 11,00 8,20 11,00 8,20 11,00 14,00
12 3 x 2 8 12 8 8 12 8 12 8 8
36,50 39,50 26,00 43,50 46,50 24,50 38,00 27,00 74,00 50-81 60,00
11 12
352,40 267,00 110,00
84,00 333,40 11,00
8
45,00
11 12 14 14 18
352,40 333,40 11,00 313,00 157,00 120,00 466,70 438,20 14,00 466,70 438,20 14,00 407,00 265,00 200,00 571,50 542,90 17,00
11 12 – 10 11 12 8 11 12 –
182,00 55,00
190,00 55,00 222,00 65,00 235,50 75,00
J 2
m 1
8 8 12
64,00 50,00 69,00 59,50
2,00
19,00
26,10
1,80
0,001
3,00
25,00
40,00 43,00 29,50
3,00
25,0044,00
24,50 46,50
4,00 3,00
38,0044,00
24,00 41,00
2,70 3,60 13,10 3,00 3,00 13,00 3,00 13,80
62,00 83,00
50,00 81,00
7,0027,00
0,010 0,040 0,050 0,010 0,030 0,040 0,030 0,050 0,030 0,060 0,160
53,00
47,00
10,80
0,040
66,00 52,00 76,00 66,50
2,80 16,70 4,70 14,20
0,070 0,180 0,240 0,520
4,00 4,00 4,00
66,00
6,00
77,00
0,001 0,010
0,010 0,020 0,020 0,040 0,100 0,410
m 2 [kg]
[kg m 2]
– –
J 1
0,300 1,100 2,800 3,300 1,100 2,200 2,700 2,200 3,400 2,800 4,300 6,200 2,800
0,500 1,700 2,000 2,100 1,900 3,200 4,400 4,300 4,000 4,600
3,800 9,400 6,200 8,900 6,600 21,900 10,700
Dimensions in mm
VULKARDAN E
09
Abmessungen/Massenträgheitsmomente/Massen Dimensions/Mass-Moments of Inertia/Masses VULKARDAN E Baureihe / Series 4110 Baugruppe / Dimension group 4010 – 4910
Baugruppe
Baugruppe / Dimension group 5410 – 5710
Schwungrad nach SAE J620
Abmessungen
Massenträgheitsmoment
flywheel
Dimensions
Mass moment of inertia
Dimension Group TKN
D 1
D 2
4910 5410 5710 6010
2,50 3,15 4,00 5,00 6,30 8,00 10,00 12,50 16,00 20,00
D 3 vorgeb. pilot bored
kNm 4010
Baugruppe / Dimension group 6010
11 12 14 14 18 18 21 18 21 21 24
427,00 150,00
D 4
50,00 105,00
484,00 170,00
60,00 120,00
538,00 180,00
70,00 125,00
636,00 210,00 684,00 224,00
Z
L kr
T
L 11)
L 2
L 3
max.
L 4
F
J 1
J 2
Masse
11,00 14,00 14,00 17,00 17,00
70,00 150,00
17,00
80,00 160,00
17,00 20,00
352,40 466,70 466,70 571,50 571,50 673,10 571,50 673,10 673,10 733,40
333,40 278,00 8 135,00 438,20 264,00 438,20 8 299,00 150,00 542,90 6 289,50 542,90 12 355,00 175,00 641,40 542,90 12 355,00 175,00 641,40 641,40 12 339,00 185,00 692,20
m 1
m 2 [kg]
2,80 0,07 0,63 3,60 1,60 16,80 0,17 0,63 6,20 8,00 0,25 1,59 6,80 6,00 1,60 17,50 0,52 1,60 11,00 0,60 13,40 6,00 – 1,60 2,70 1,08 17,90 0,80 4,50 15,40 6,00 – 1,60 1,21 4,51 20,00 – 1,47 22,90 6,00 1,60 5,40 – 1,87 26,10 4,00
46,50 83,50 80,60 110,60
s 2 [mm]
9,20 3,50 7,70 0,40 18,00 14,00
145,70 172,00 170,00 179,00
16,00 175,00
134,00
26,00 156,00 22,80
1) The overall dimension L1 can be adapted to the actual application.
Maße in mm Alle Massen und Massenträgheitsmomente beziehen sich auf vorgebohrte Naben.
Dimensions in mm All masses and mass moments of inertia refer to pilot bored hubs.
VULKARDAN E
s 1
143,00 142,70
1) Das Einbaumaß L1 kann je nach Einbausituation angepaßt werden.
10
Distance to centre of grafity
Mass
[kg m 2]
Schwerpunktsabstand
A/M-4110-1
VULKARDAN E Baureihe / Series 4111 Baugruppe / Dimension group 4010 – 4910
Baugruppe Dimension Group
Abmessungen
Massenträgheitsmoment
flywheel
Dimensions
Mass moment of inertia
D 1
kNm
4910 5410 5710 6010
2,50 3,15 4,00 5,00 6,30 8,00 10,00 12,50 16,00 20,00
Baugruppe / Dimension group 6010
Schwungrad nach SAE J620
TKN
4010
Baugruppe / Dimension group 5410 – 5710
11 12 14 14 18 18 21 18 21 21 24
D 2
vorgeb. pilot bored
D 3
max.
D 4
11,00 14,00 14,00 484,00 170,00 60,00 120,00 17,00 538,00 180,00 70,00 125,00 17,00 538,00 180,00 70,00 125,00
Z
352,40 466,70 466,70 571,50 571,50 673,10 571,50 636,00 210,00 70,00 150,00 17,00 673,10 17,00 673,10 684,00 224,00 80,00 160,00 20,00 733,40 427,00 150,00 50,00 105,00
L kr
T
L 11)
L 2
L 3
L 4
F
J 1
J 2 [kg m2]
333,40 438,20 438,20 542,90 542,90 641,40 542,90 641,40 641,40 692,20
278,00 2,80 135,00 4,00 264,00 16,80 8,00 299,00 8,00 150,00 6,00 6,00 289,50 17,50 – 12,00 355,00 175,00 6,00 – – 12,00 355,00 175,00 6,00 – – 12,00 339,00 185,00 6,00 – 8,00
1,60 1,60 1,60 1,60 1,60
0,080 0,190 0,280 0,560 0,710 1,160 0,750 1,270 1,640 1,970
0,700 1,690 2,690 4,520 5,310
Masse
Distance to centre of grafity
Mass m 1
m 2 [kg]
s 1
s 2 [mm]
4,800 4,10 49,000 154,00 7,200 4,20 8,600 2,50 84,600 165,00 12,700 4,40 17,200 22,00 106,600 176,00 21,800 33,70 17,000 14,80 142,900 175,00 23,100 18,00 29,100 28,00 136,530 159,00 31,630 22,80
1) Das Einbaumaß L1 kann je nach Einbausituation angepaßt werden.
1) The overall dimension L1 can be adapted to the actual application.
Maße in mm Alle Massen und Massenträgheitsmomente beziehen sich auf vorgebohrte Naben.
Dimensions in mm All masses and mass moments of inertia refer to pilot bored hubs.
A/M-4111-1
Schwerpunktsabstand
VULKARDAN E
11
Abmessungen/Massenträgheitsmomente/Massen Dimensions/Mass-Moments of Inertia/Masses VULKARDAN E Baureihe / Series 4400 Baugruppe / Dimension group 4110 – 4810
Baugruppe / Dimension group 5410 – 5710
Baugruppe / Dimension group 6010
Baugruppe
Abmessungen
Massenträgheitsmoment
Dimension Group
Dimensions
Mass moment of inertia
TKN
D 1
D 2
kNm
vorgeb. pilot bored
D 3
max.
vorgeb. pilot bored
D 4
max.
D 5
D 6
L 11)
L 2
L 3
F1
F2
J 1
J 2 [kg m2]
Masse
Distance to centre of grafity
Mass m 1
m 2 [kg]
s 1
s 2 [mm]
4110
2,50 3,15
417,00 140,00
40,00 100,00
40,00 100,00 140,00
–
324,00 125,00 125,00
1,60
1,60
0,220
0,400
26,120
27,260
92,40
4810
4,00 5,00
474,00 170,00
60,00 120,00
60,00 120,00 170,00
–
354,80 135,00 135,00
2,00
2,00
0,400
0,880
37,860
45,020
97,60 107,50
5410
6,30 8,00
625,00 210,00
70,00 150,00
70,00 150,00 210,00
–
470,35 175,00 175,00
1,60
1,60
1,130
3,650
74,900 116,500 125,00 143,00
5710
10,00 12,50
625,00 210,00
70,00 150,00
70,00 150,00 210,00
–
470,35 175,00 175,00
1,60
1,60
1,430
3,770
80,100 118,400 128,00 144,00
6010
16,00 20,00
684,00 224,00
80,00 160,00
80,00 160,00 224,00 682,00 539,00 185,00 185,00
1,60
1,60
5,040
5,380 130,400 134,000 157,00 156,00
1) Das Einbaumaß L1 kann je nach Einbausituation angepaßt werden.
1) The overall dimension L1 can be adapted to the actual application.
Maße in mm Alle Massen und Massenträgheitsmomente beziehen sich auf vorgebohrte Naben.
Dimensions in mm All masses and mass moments of inertia refer to pilot bored hubs.
12
Schwerpunktsabstand
VULKARDAN E
97,00
A/M-4400-1
Weitere Ausführungen Further Executions
Sonderausführungen auf Anfrage / Special design on request 2-reihige PTO Ausführung / 2-row PTO execution
Für größeres Einbaumaß / For larger installation dimension
Doppelmembrane für sehr geringe Axialkräfte / Double-membrane for very low axial reaction forces
Mit langem Distanzstück / With long spacer
Elastisches Element mit kardanischer Zwischenwelle / Flexible element with cardanic intermediate shaft
Doppelelement für geringe torsionale und radiale Steifigkeit / Double-element for low torsional and radial stiffness
VULKARDAN E
13