Technical Services 8 66-500-4768 | +1-401-781-8220 www.grinnell.com
GRINNELL Stainless Steel, Full-Flow Grooved Fittings General Description
Technical Data
GRINNELL Stainless Steel, Full-Flow Grooved fittings are made of lightweight, corrosion-resistant Type 304 and 316 stainless steel. The assortment of available fittings provides economical and efficient methods to change direction in, add outlets to, reduce, or cap piping systems.
Approvals UL, ULC, IAPMO, and NSF-61 Annex G
•WARNING Never remove any piping component or correct or modify any piping deficiencies without first de-pressurizing and draining the system. Failure to do so may result in serious personal injury, property damage, and/or impaired device performance. It is the Designer’s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data are not exceeded. Material and gasket selection should be verified for compatibility with the specific application. Always read and understand the installation instructions. The GRINNELL Grooved Fittings described herein must be installed and maintained in compliance with this document, in addition to the standards of any authorities having jurisdiction. Failure to do so may result in serious personal injury or impair the performance of these devices. Owners are responsible for maintaining their mechanical system and devices in proper operating condition. The installing contractor or device manufacturer should be contacted with any questions.
Maximum Working Pressure See specific data sheet for rating of coupling in use. Material Type 304 or Type 316 Stainless Steel conforming to ASTM A 403 WPW or ASTM A 403 CR Fittings are Schedule 10 wall thickness. For Schedule 40, contact your GRINNELL representative.
Limited Warranty Products manufactured by Tyco Fire Suppression & Building Products (TFSBP) are warranted solely to the original Buyer for ten (10) years against defects in material and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFSBP. No warranty is given for products or components manufactured by companies not affiliated by ownership with TFSBP or for products and components which have been subject to misuse, improper installation or maintenance, corrosion, or other external sources of damage. Materials found by TFSBP to be defective shall be either repaired or replaced, at TFSBP’s sole option. TFSBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. TFSBP shall not be responsible for system design errors or inaccurate or incomplete information supplied by Buyer or Buyer’s representatives.
UP
C
®
Certified to NSF/ANSI 61-G
For more information on approvals, contact your GRINNELL representative.
In no event shall TFSBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential damages, including but not limited to labor charges, regardless of whether TFSBP was informed about the possibility of such damages, and in no event shall TFSBP’s liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties, express or implied, including warranties of merchantability and fitness for a particular purpose. This limited warranty sets forth the exclusive remedy for claims based on failure of or defect in products, materials or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full extent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder.
Ordering Procedure GRINNELL Products are available globally through a network of distribution centers. Visit www.grinnell. com for the nearest distributor. When placing an order, indicate the full product name. Specify quantity, figure number, material (Type 304 or 316 Stainless Steel), and nominal size. Fittings are Schedule 10 wall thickness. For Schedule 40, contact your GRINNELL sales representative.
Page 1 of 8
June 2010
G570
G570 Page 2 of 8
C to E
C to E FIGURE 410 90° ELBOW
FIGURE 401 45° ELBOW Figure 410
Nominal Size ANSI Inches DN
Pipe O.D. Inches (mm)
1 DN25
Figure 401
Nominal C to E Inches (mm)
Approx. Weight Lbs. (kg)
Nominal C to E Inches (mm)
Approx. Weight Lbs. (kg)
1.315 (33,4)
2.88 (73,2)
1.0 (0,45)
2.00 (50,8)
0.6 (0,27)
1-1/4 DN32
1.660 (42,4)
3.13 (79,5)
1.0 (0,45)
2.00 (50,8)
0.8 (0,36)
1-1/2 DN40
1.900 (48,3)
3.50 (88,9)
1.0 (0,45)
3.50 (88,9)
1.0 (0,45)
2 DN50
2.375 (60,3)
4.50 (114,3)
1.1 (0,50)
2.75 (69,9)
1.2 (0,54)
2-1/2 DN65
2.875 (73,0)
5.00 (127,0)
1.7 (0,77)
2.81 (71,4)
1.7 (0,77)
3 DN80
3.500 (88,9)
4.50 (114,3)
2.6 (1,18)
2.00 (50,8)
1.3 (0,59)
4 DN100
4.500 (114,3)
6.00 (152,4)
4.7 (2,13)
2.50 (63,5)
2.3 (1,04)
5 DN125
5.563 (141,3)
7.50 (190,5)
8.4 (3,81)
3.13 (79,4)
4.2 (1,90)
6 DN150
6.625 (168,3)
9.00 (228,6)
10.3 (4,67)
3.75 (95,3)
5.1 (2,31)
8 DN200
8.625 (219,1)
12.00 (304,8)
17.6 (7,98)
5.00 (127,0)
13.8 (6,26)
10 DN250
10.750 (273,0)
15.00 (381,0)
49.2 (22,32)
6.25 (158,8)
24.6 (11,16)
12 DN300
12.750 (323,9)
18.00 (457,2)
78.4 (35,56)
7.50 (190,5)
39.2 (17,78)
Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 1 FIGURE 410 90° ELBOW AND FIGURE 401 45° ELBOW — NOMINAL DIMENSIONS —
G570 Page 3 of 8
E to E
E to E
FIGURE 460 1” - 4” END CAP
FIGURE 460 5” - 12” END CAP
Nominal Size ANSI Inches DN
Pipe O.D. Inches (mm)
Nominal E to E Inches (mm)
Approx. Weight Lbs. (kg)
1 DN20
1.315 (33,4)
1.08 (27,5)
0.2 (0,09)
1-1/4 DN32
1.660 (42,4)
1.08 (27,5)
0.4 (0,09)
1-1/2 DN40
1.900 (48,3)
1.08 (27,5)
0.5 (0,09)
2 DN50
2.375 (60,3)
1.08 (27,5)
0.7 (0,09)
2-1/2 DN65
2.875 (73,0)
1.08 (27,5)
1.0 (0,45)
3 DN80
3.500 (88,9)
1.08 (27,5)
2.0 (0,91)
4 DN100
4.500 (114,3)
1.13 (28,7)
3.1 (1,41)
5 DN125
5.563 (141,3)
3.00* (76,2)
1.5 (0,68)
6 DN150
6.625 (168,3)
3.50* (88,9)
1.5 (0,68)
8 DN200
8.625 (219,1)
4.00* (101,6)
3.1 (1,41)
10 DN250
10.750 (273,0)
5.00* (127,0)
6.0 (2,72)
12 DN300
12.750 (323,9)
6.00* (152,4)
7.8 (3,54)
* Dished Cap Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 2 FIGURE 460 END CAP — NOMINAL DIMENSIONS —
G570 Page 4 of 8
C to E
C to E FIGURE 419 TEE
Nominal Size ANSI Inches DN
Pipe O.D. Inches (mm)
1 DN20 1-1/4 DN32 1-1/2 DN40
1.315 (33,4) 1.660 (42,4) 1.900 (48,3)
2 DN50
2.375 (60,3)
2-1/2 DN65
2.875 (73,0)
3 DN80 4 DN100 5 DN125 6 DN150 8 DN200 10 DN250 12 DN300
3.500 (88,9) 4.500 (114,3) 5.563 (141,3) 6.625 (168,3) 8.625 (219,1) 10.750 (273,0) 12.750 (323,9)
Nominal C to E Inches (mm) 2.88 (73,2) 3.38 (85,9) 3.38 (85,9) 2.75 Non-US (69,9) 4.00 US (101,6) 3.07 Non-US (78,0) 4.63 US (117,6) 3.77 (95,8) 4.47 (113,5) 5.91 (150,1) 5.91 (150,1) 7.79 (197,9) 8.89 (225,8) 10.39 (263,9)
Approx. Weight Lbs. (kg) 1.0 (0,45) 1.5 (0,68) 1.6 (0,73) 2.3 (1,04) 1.8 (0,82) 2.2 (1,00) 3.6 (1,63) 3.1 (1,41) 4.9 (2,22) 7.1 (3,49 ) 11.7 (5,31) 20.0 (9,07) 34.4 (15,60) 52.5 (23,81)
Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 3 FIGURE 419 TEE — NOMINAL DIMENSIONS —
G570 Page 5 of 8
Nominal Size ANSI Inches DN
Pipe O.D. Inches (mm)
Nominal C to E Inches (mm)
Nominal C to B Inches (mm)
Approx. Weight Lbs. (kg)
1-1/2 x 1-1/2 x 1 DN40 x DN40 x DN25 1-1/2 x 1-1/2 x 1-1/4 DN40 x DN40 x DN32 2x2x1 DN50 x DN50 x DN25 2 x 2 x 1-1/4 DN50 x DN50 x DN32 2 x 2 x 1-1/2 DN50 x DN50 x DN40 2-1/2 x 2-1/2 x 1 DN50 x DN50 x DN40 2-1/2 x 2-1/2 x 1-1/2 DN50 x DN50 x DN40 2-1/2 x 2-1/2 x 2 DN50 x DN50 x DN40 3x3x1 DN80 x DN80 x DN25 3 x 3 x 1-1/4 DN80 x DN80 x DN32 3 x 3 x 1-1/2 DN80 x DN80 x DN40 3x3x2 DN80 x DN80 x DN50 3 x 3 x 2-1/2 DN80 x DN80 x DN65 4x4x2 DN100 x DN100 x DN50 4 x 4 x 2-1/2 DN100 x DN100 x DN65 4x4x3 DN100 x DN100 x DN80 6 x 6 x 1-1/2 DN150 x DN150 x DN40 6x6x2 DN150 x DN150 x DN50 6x6x3 DN150 x DN150 x DN80 6x6x4 DN150 x DN150 x DN100 8x8x4 DN200 x DN200 x DN100 8x8x6 DN200 x DN200 x DN150 10 x 10 x 6 DN250 x DN250 x DN150 10 x 10 x 8 DN250 x DN250 x DN200 12 x 12 x 8 DN300 x DN300 x DN200 12 x 12 x 10 DN300 x DN300 x DN250
1.900 x 1.900 x 1.315 (48,3 x 48,3 x 33,4) 1.900 x 1.900 x 1.660 (48,3 x 48,3 x 42,4) 2.375 x 2.375 x 1.315 (60,3 x 60,3 x 33,4) 2.375 x 2.375 x 1.660 (60,3 x 60,3 x 42,4) 2.375 x 2.375 x 1.900 (60,3 x 60,3 x 48,3) 2.375 x 2.375 x 1.315 (60,3 x 60,3 x 33,4) 2.375 x 2.375 x 1.900 (60,3 x 60,3 x 48,3) 2.375 x 2.375 x 2.375 (60,3 x 60,3 x 60,3) 3.500 x 3.500 x 1.315 (88,9 x 88,9 x 33,4) 3.500 x 3.500 x 1.660 (88,9 x 88,9 x 42,2) 3.500 x 3.500 x 1.900 (88,9 x 88,9 x 48,3) 3.500 x 3.500 x 2.375 (88,9 x 88,9 x 60,3) 3.500 x 3.500 x 2.875 (88,9 x 88,9 x 73,0) 4.500 x 4.500 x 2.375 (114,3 x 114,3 x 60,3) 4.500 x 4.500 x 2.875 (114,3 x 114,3 x 73,0) 4.500 x 4.500 x 3.500 (114,3 x 114,3 x 88,9) 6.625 x 6.625 x 1.900 (168,3 x 168,3 x 48,3) 6.625 x 6.625 x 2.375 (168,3 x 168,3 x 88,9) 6.625 x 6.625 x 3.500 (168,3 x 168,3 x 60,3) 6.625 x 6.625 x 4.500 (168,3 x 168,3 x 114,3) 8.625 x 8.625 x 4.500 (219,1 x 219,1 x 114,1) 8.625 x 8.625 x 6.625 (219,1 x 219,1 x 168,3) 10.750 x 10.750 x 6.625 (273,0 x 273,0 x 168,3) 10.750 x 10.750 x 8.625 (273,0 x 273,0 x 219,1) 12.750 x 12.750 x 8.625 (323,9 x 323,9 x 219,1) 12.750 x 12.750 x 10.750 (323,9 x 323,9 x 273,0)
3.38 (85,9) 3.38 (85,9) 3.25 (82,6) 3.25 (82,6) 2.75 (69,9) 3.75 (95,3) 3.75 (95,3) 3.07 (78,0) 4.25 (108,0) 4.25 (108,0) 4.25 (108,0) 3.77 (95,8) 3.77 (95,8) 4.47 (113,5) 5.00 (113,5) 4.47 (113,5) 5.91 (150,1) 5.91 (150,1) 5.91 (150,1) 5.91 (150,1) 7.79 (197,9) 7.79 (197,9) 8.89 (225,8) 8.89 (225,8) 10.39 (263,9) 10.39 (263,9)
3.38 (85,9) 3.38 (85,9) 3.38 (69,9) 3.25 (82,6) 2.75 (69,9) 3.75 (95,3) 3.75 (95,3) 3.07 (78,0) 4.25 (108,0) 4.25 (108,0) 4.25 (108,0) 3.23 (82,0) 3.23 (82,0) 3.82 (97,0) 5.00 (113,5) 3.38 (69,9) 5.91 (150,1) 5.91 (150,1) 4.88 (124,0) 5.12 (130,0) 6.31 (160,3) 6.62 (168,1) 7.70 (195,6) 8.59 (218,2) 9.51 (242,0) 9.89 (251,2)
1.6 (0,73) 1.6 (0,73) 2.2 (1,00) 2.4 (1,09) 2.4 (1,09) 3.1 (1,41) 3.4 (1,54) 3.6 (1,63) 4.3 (1,95) 4.3 (1,95) 4.4 (2,00) 4.4 (2,00) 4.4 (2,00) 4.4 (2,00) 4.4 (2,00) 4.9 (2,22) 9.3 (4,22) 9.3 (4,22) 9.3 (4,22) 9.3 (4,22) 18.1 (8,21) 18.1 (8,21) 29.3 (13,29) 31.7 (14,38) 44 (19,96) 44 (19,96)
Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 4 FIGURE 421 REDUCING TEE — NOMINAL DIMENSIONS —
C to B
C to E FIGURE 421 REDUCING TEE
G570 Page 6 of 8
Nominal Size ANSI Inches DN
Pipe O.D. Inches (mm)
Nominal E to E Inches (mm)
Approx. Weight Lbs. (kg)
1-1/2 x 1 DN40 x DN25 1-1/2 x 1-1/4 DN40 x DN32 2x1 DN50 x DN25 2 x 1-1/4 DN50 x DN32 2 x 1-1/2 DN50 x DN40 2-1/2 x 1-1/2 DN65 x DN40 2-1/2 x 2 DN65 x DN50 3x1 DN80 x DN25 3 x 1-1/4 DN80 x DN32 3 x 1-1/2 DN80 x DN40 3x2 DN80 x DN50 3 x 2-1/2 DN80 x DN65 4x2 DN100 x DN50 4 x 2-1/2 DN100 x DN65 4x3 DN100 x DN80 5x3 DN125 x DN80 5x4 DN125 x DN100
1.900 x 1.315 (48,3 x 33,7) 1.900 x 1.660 (48,3 x 42,4) 2.375 x 1.315 (60,3 x 33,7) 2.375 x 1.660 (60,3 x 42,4) 2.375 x 1.900 (60,3 x 48,3) 2.875 x 1.900 (73,0 x 48,3) 2.875 x 2.375 (73,0 x 60,3) 3.500 x 1.315 (88,9 x 33,7) 3.500 x 1.660 (88,9 x 42,4) 3.500 x 1.900 (88,9 x 48,3) 3.500 x 2.375 (88,9 x 60,3) 3.500 x 2.875 (88,9 x 73,0) 4.500 x 2.375 (114,3 x 60,3) 4.500 x 2.875 (114,3 x 73,0) 4.500 x 3.500 (114,3 x 88,9) 5.563 x 3.500 (141,3 x 88,9) 5.563 x 4.500 (141,3 x 114,3)
3.75 (95,3) 3.75 (95,3) 3.75 (95,3) 3.75 (95,3) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 9.00 (228,6) 9.00 (228,6)
1.4 (0,64) 1.4 (0,64) 1.5 (0,68) 2.5 (1,13) 2.5 (1,13) 3.5 (1,59) 3.5 (1,59) 4.0 (1,81) 4.3 (1,95) 4.4 (2,00) 4.8 (2,17) 4.8 (2,17) 4.8 (2,17) 4.8 (2,17) 5.0 (2,27) 7.0 (3,18) 7.0 (3,18)
Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 5 (1 OF 2) FIGURE 450 CONCENTRIC REDUCER — NOMINAL DIMENSIONS —
E to E
FIGURE 450 CONCENTRIC REDUCER
G570 Page 7 of 8
Nominal Size ANSI Inches DN 6x2 DN150 x DN50 6 x 2-1/2 DN150 x DN65
Pipe O.D. Inches (mm)
6x3 DN150 x DN80
6.625 x 3.500 (168,3 x 88,9)
6x4 DN150 x DN100
6.625 x 4.500 (168,3 x 114,3)
8x4 DN200 x DN100
8.625 x 4.500 (219,1 x 114,3)
8x6 DN200 x DN150 10 x 4 DN250 x DN100
8.625 x 6.625 (219,1 x 168,3) 10.750 x 4.500 (273,0 x 114,3)
10 x 6 DN250 x DN150
10.750 x 6.625 (273,0 x 168,3)
10 x 8 DN250 x DN200 12 x 6 DN300 x DN150 12 x 8 DN300 x DN200 12 x 10 DN300 x DN250
10.750 x 8.625 (273,0 x 219,1) 12.750 x 6.625 (323,9 x 168,3) 12.750 x 8.625 (323,9 x 219,1) 12.750 x 10.750 (323,9 x 273,0)
6.625 x 2.375 (168,3 x 60,3) 6.625 x 2.875 (168,3 x 73,0)
Nominal E to E Inches (mm) 9.00 (228,6) 15.00 (381,0) 5.50 Non-US (139,7) 9.00 US (228,6) 5.50 (139,7) 6.00 Non-US (152,4) 9.00 US (228,6) 6.00 (152,4) 10.00 (254,0) 7.00 Non-US (177,8) 10.00 US (254,0) 7.00 (177,8) 14.00 (355,6) 14.00 (355,6) 14.00 (355,6)
Approx. Weight Lbs. (kg) 7.0 (3,18) 7.0 (3,18) 6.9 (3,13) 7.4 (3,36) 7.0 (3,18) 9.6 (4,35) 7.1 (3,22) 9.6 (4,35) 12.4 (5,62) 12.4 (5,62) 21.0 (9,53) 14.9 (6,76) 22.0 (9,98) 22.0 (9,98) 26.0 (11,79)
Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 5 (2 OF 2) FIGURE 450 CONCENTRIC REDUCER — NOMINAL DIMENSIONS —
E to E
FIGURE 450 CONCENTRIC REDUCER
G570 Page 8 of 8
Nominal Size ANSI Inches DN
Pipe O.D. Inches (mm)
Nominal E to E Inches (mm)
Approx. Weight Lbs. (kg)
1-1/2 x 1 DN40 x DN25 1-1/2 x 1-1/4 DN40 x DN32 2x1 DN50 x DN25 2 x 1-1/4 DN50 x DN32 2 x 1-1/2 DN50 x DN40 2-1/2 x 2 DN65 x DN50 3x1 DN80 x DN25 3x2 DN80 x DN50 3 x 2-1/2 DN80 x DN65 4x2 DN100 x DN50 4 x 2-1/2 DN100 x DN65 4x3 DN100 x DN80 5x3 DN125 x DN80 5x4 DN125 x DN100 6x2 DN150 x DN50 6 x 2-1/2 DN150 x DN65 6x3 DN150 x DN80
1.900 x 1.315 (48,3 x 33,7) 1.900 x 1.660 (48,3 x 42,4) 2.375 x 1.315 (60,3 x 33,7) 2.375 x 1.660 (60,3 x 42,4) 2.375 x 1.900 (60,3 x 48,3) 2.875 x 2.375 (73,0 x 60,3) 3.500 x 1.315 (88,9 x 33,4) 3.500 x 2.375 (88,9 x 60,3) 3.500 x 2.875 (88,9 x 73,0) 4.500 x 2.375 (114,3 x 60,3) 4.500 x 2.875 (114,3 x 73,0) 4.500 x 3.500 (114,3 x 88,9) 5.563 x 3.500 (141,3 x 88,9) 5.563 x 4.500 (141,3 x 114,3) 6.625 x 2.375 (168,3 x 60,3) 6.625 x 2.875 (168,3 x 73,0) 6.625 x 3.500 (168,3 x 88,9)
3.75 (95,3) 3.75 (95,3) 3.75 (95,3) 3.75 (95,3) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 5.00 (127,0) 9.00 (228,6) 9.00 (228,6) 9.00 (228,6) 9.00 (228,6) 9.00 (228,6)
6x4 DN150 x DN100
6.625 x 4.500 (168,3 x 114,3)
8x3 DN200 x DN80 8x4 DN200 x DN100 8x6 DN200 x DN150 10 x 6 DN250 x DN150 10 x 8 DN250 x DN200 12 x 6 DN300 x DN150 12 x 8 DN300 x DN200 12 x 10 DN300 x DN250
8.625 x 3.500 (219,1 x 88,9) 8.625 x 4.500 (219,1 x 114,3) 8.625 x 6.625 (219,1 x 168,3) 10.750 x 6.625 (273,0 x 168,3) 10.750 x 8.625 (273,0 x 219,1) 12.750 x 6.625 (323,9 x 168,3) 12.750 x 8.625 (323,9 x 219,1) 12.750 x 10.750 (323,9 x 273,0)
1.4 (0,64) 1.4 (0,64) 1.5 (0,68) 2.5 (1,13) 2.5 (1,13) 3.5 (1,59) 4.3 (1,95) 4.3 (1,95) 4.5 (1,95) 4.8 (2,18) 5.8 (2,63) 5.9 (2,68) 5.9 (2,68) 7.0 (3,18) 7.0 (3,17) 7.0 (3,17) 7.0 (3,18) 7.0 (3,18) 8.2 (3,72) 9.3 (4,22) 9.3 (4,22) 7.0 (3,18) 12.4 (5,62) 11.5 (5,22) 21.1 (9,57) 21.1 (9,57) 21.1 (9,57)
Non-US US
5.00 (127,0) 9.00 (228,6)
10.00 (254,0) 12.00 (304,8) 8.00 (203,2) 13.00 (330,2) 13.00 (330,2) 14.00 (355,6) 14.00 (355,6) 14.00 (355,6)
E to E
FIGURE 451 ECCENTRIC REDUCER
Dimensions for U.S. and Non-U.S. sourced products are identical unless indicated otherwise.
FIGURE 6 FIGURE 451 ECCENTRIC REDUCER — NOMINAL DIMENSIONS —
Copyright © 2006-2010 Tyco Fire Suppression & Building Products. All rights reserved. Certified Company
