SUPERIOR METAL PRODUCTS LLC Walkway Cover Systems for Commercial, Industrial and Educational Facilities

Entrance Canopy Tyler, TX

Gardendale Medical Complex Gardendale, AL

Navy Federal Credit Union Pensacola, FL

Plantside III Louisville, KY

Ticket Booth Cover Tuscaloosa, AL

Liberty County High School Liberty County, GA

Southern Research Institute Birmingham, AL

The Chef’s Academy Indianapolis, IN

Aluminum Bus Shelter Birmingham, AL

116 Citation Court Birmingham, AL 35209-6307

Engineered Aluminum Canopies and Walkway Covers

Visit us at: www.SuperiorMetalProducts.com

p. 877.445.1200 f. 205.945.5694

SUPERIOR METAL PRODUCTS LLC email: [email protected] SUPERIOR QUALITY

Bluffton Middle School Bluffton, SC

SUPERIOR PRODUCTS 1.01 DESCRIPTION OF WORK Extent of canopies required is shown on the drawings. Included herein, but not limited to, are decking, fascia/gutter, columns, anchors, supports, and flashing.

Superior Metal Products LLC manufactures a complete line of rollformed and extruded canopies and walkway covers. From the smallest door canopy to the largest walkway cover, all materials are fabricated in the company’s Birmingham, AL facility and undergo constant inspection and quality control. Innovative mechanical assembly procedures allow economical shipping to all points serviced by common carrier freight lines. Extruded systems are available in both painted and anodized finishes to harmonize with the widest range of architectural designs. Rollformed components are manufactured from only the highest quality, pre-tested and approved by independent registered structural engineers and are in compliance with the requirements of the International Code Council. Detailed shop drawings bearing the seal of a Registered Engineer are provided when required, and specification, design, and installation assistance is never more than a phone call away. Visit the company’s web site at www.superiormetalproducts.com.

1.02 MEASUREMENTS Verify all measurements shown on drawings by taking field measurements to insure proper fit and attachment of all component parts. 1.03 SUBMITTALS Provide manufacture shop drawings, including fabrication and installation details. 1.04 COORDINATION Provide necessary anchors, blockouts, flashing and other items required to be built in ample time to avoid delays to the job. 1.05 DELIVERY & STORAGE Deliver and store all items in protected area. Keep free of any damage. Replace any damaged items or parts at no cost to the Owner. 1.06 DESIGN PARAMETERS Live load of canopies shall be no less than 20 p.s.f. Canopies shall comply in all respects with the International Code Council requirements for Floor, Wall and Roof systems.

U.S. Post Office Prattville, AL

1.07 ACCEPTABLE MANUFACTURER Subject to compliance with requirements herein, provide product manufactured by Superior Metal Products LLC, Birmingham, Alabama. 1.08 PRODUCTS AND MATERIALS Consult Superior Metal Products’ Architect Manual and design staff for detailed specifications of materials and products. 1.09 INSTALLATION Canopies shall be installed according to approved plans and shop drawings and the entire structure shall be erected straight true and plumb in accordance with standard construction procedures. All joints and connections shall be tight and clean, and all surfaces of work left in a clean condition.

2

Call Toll Free: 1.877.445.1200

Westlawn Middle School Tuscaloosa, AL

Aluminum Canopies and Walkway Covers

CONFIGURATIONS STANDARD

GABLE CANOPY

DOUBLE OVERHANG

12 6

DRAIN BEAM

POST UNDER GUTTER ( NO OVERHANG )

BUS CANOPY

( WITH DRAIN BEAM )

OVERHEAD SUPPORT

SINGLE OVERHANG

C-BEAM

WALL-ATTACHED

DRAIN BEAM

DOUBLE OVERHANG

GABLE CANOPY

DRAIN BEAM

BUS CANOPY

SINGLE OVERHANG ( WITH DRAIN BEAM )

)

STRUCTURAL COMPONENTS

3" X 3" X .125 EXTRUDED ALUMINUM COLUMN

4" X 4" X .125 EXTRUDED ALUMINUM COLUMN

6" X 4-1/2" X .188 EXTRUDED ALUMINUM COLUMN

6" X 6" X .188 EXTRUDED ALUMINUM COLUMN

8" X 4" X .250 EXTRUDED ALUMINUM COLUMN

8" X 2-1/2" 12 GA. STEEL C-BEAM

8" X 4" X .350 EXTRUDED ALUMINUM C-BEAM

10" X 2-1/2" X .150 EXTRUDED ALUMINUM C-BEAM

3" X 3" 14 GA. STEEL COLUMN

5-1/2" X 3" X .100 EXTRUDED ALUMINUM FASCIA/GUTTER

6" X 1" X .094 EXTRUDED ALUMINUM SIDE FASCIA

6" X 3" X .050 ROLLFORMED ALUMINUM FASCIA/GUTTER

7" X 3" X .094 EXTRUDED ALUMINUM FASCIA/GUTTER

7" X 4" X .094 EXTRUDED ALUMINUM FASCIA/GUTTER

6" X 3" X .125 EXTRUDED ALUMINUM DRAIN BEAM

6" X 4" X .125 EXTRUDED ALUMINUM DRAIN BEAM

)

STANDARD COLORS

Pictured: Superior’s 7” X 3” Extruded Aluminum Fascia/Gutter

WHITE

BRONZE

CREAM

Clear anodized and Bronze anodized also available. Call for information on additional colors and availability. Please Note: Superior cannot guarantee an exact color match with this sample chart and actual materials. Some color deviation is normal and expected.

3

SUPERIOR METAL PRODUCTS LLC email: [email protected]

SUPERIOR Extruded Decking ECONO DECKING

FLUSH DECKING

LONG SPAN DECKING

.062 6063-T6 extruded aluminum decking sections offer maximum economy for spans to 14’ 8” at 20 p.s.f. live load L/60 deflection.

.062 6063-T6 extruded aluminum decking sections provide smooth underside to decking system with no exposed openings for spans to 16’ 2” at 20 p.s.f. live load and L/60 deflection.

.075 6063-T6 extruded aluminum decking sections allow increased column of bent spacing for spans to 20’ 0” at 20 p.s.f. live load limiting deflection to L/60. REF: #95131 Compliance Report

8” X 4” X .350 EXTRUDED ALUMINUM C-BEAM Proj.

5’ 6’ 7’ 8’ 9’ 10’ 11’ 12’ 13’ 14’ 15’

20

psf

34’0” (34’8”) 31’0” (32’7”) 28’9” (30’11”) 26’11” (29’7”) 25’4” (28’6”) 24’1” (27’1”) 22’11” (25’10”) 21’11” (24’8”) 21’1” (23’9”) 20’4” (22’10”) 19’8” (22’1”)

30 psf

40 psf

28’3” (30’8”) 25’10” (28’10”) 23’11” (26’11”) 22’4” (25’2”) 21’1” (23’9”) 20’0” (22’6”) 19’1” (21’6”) 18’3” (20’7”) 17’7” (19’9”) 16’11” (19’0”) 16’4” (18’5”)

24’9” (27’10”) 22’7” (25’5”) 20’11” (23’6”) 19’7” (22’0”) 18’5” (20’9”) 17’6” (19’8”) 16’8” (18’9”) 16’0” (18’0”) 15’4” (17’3”) 14’9” (16’8”) 14’3” (16’1”)

SPANS IN PARENTHESIS ARE REACHED USING 6005-T5

10” X 2.5” ALUMINUM C-BEAM Proj. 6’ 8’ 10’ 12’ 14’

4

10 psf 25’4” 23’5” 21’9” 20’0” 17’8”

20 psf 23’6” 20’5” 20’4” 18’7” 17’2”

30 psf 19’4” 16’9” 15’0” 13’9” 12’9”

40 psf 16’10” 14’7” 13’1” 11’11” 11’1”

(6063 - T6)

5.5” EXTRUDED GUTTER

(.100)

Proj. 7’ 8’ 10’ 11’ 12’ 13’ 14’

40 psf 8’2” 7’7”

10 psf 14’4” 13’9” 12’10” 12’5” 12’1” 11’7” 11’2”

20 psf 11’4” 10’8” 9’6” 9’1” 8’9” 8’4” 8’1”

30 psf 9’4” 8’9” 7’10” 7’6” 7’2”

7” EXTRUDED GUTTER Proj. 4’ 5’ 6’ 7’ 8’ 9’ 10’ 11’ 12’ 13’ 14’

10 psf 22’3” 21’0” 20’0” 19’2” 18’5” 17’9” 17’2” 16’5” 15’9” 14’11’ 13’11”

20 psf 19’9” 17’8” 16’1” 14’11” 13’11” 13’2” 12’6” 11’11” 11’5” 10’11” 10’6”

Call Toll Free: 1.877.445.1200

7’6”

(.094)

30 psf 16’4” 14’7” 13’3” 12’3” 11’6” 10’10” 10’3” 9’9”

Beaufort High School Beaufort, SC.

40 psf 14’3” 12’8” 11’7” 10’8” 10’0” 9’5” 8’11”

W.T. Sampson High School Guantanamo Bay, Cuba

Aluminum Canopies and Walkway Covers

SUPERIOR Rollformed Panels 16” X 3” W-PAN

Rollformed aluminum w-pans provide maximum coverage per dollar. Available in .025 and .032 metal thickness for spans to 14’ 1” at 20 p.s.f. live load and L/60 deflection.

12” X 3” FLAT PAN

INSULATED ROOF

Rollformed aluminum flat pans provide smooth underside. Available in .025 and .032 metal thickness for spans to 12’ 1” at 20 p.s.f. live load and L/60 deflection.

Tongue & Groove Stucco embossed .032 aluminum coil laminated to expanded polystyrene core for 3” or 4” thick panels.

.125 EXTRUDED ALUMINUM DRAIN BEAMS Proj. 4’ 5’

6”

6”

6’

4”

7’

NOTE: Spans in parenthesis are for 6”X 4” drain beam.

8’

3”

9’ 10’ 11’ 12’

HD/OH SUPPORT UAB School of Engineering Birmingham, AL

Proj. 4’ 5’ 6’ 7’ 8’ 9’ 10’ 11’ 12’

20 psf 19’8” 15’8” 13’2” 11’2” 9’10” 8’8” 7’10” 7’1” 6’2”

30 psf 13’4” 10’8” 8’10” 7’7” 6’7” 5’11” 5’3” 4’10” 4’2”

40 psf 10’0” 8’0” 6’8” 5’8” 5’0” 4’5” 4’0” 3’11” 3’8”

13’ 14’ 15’ 16’ 17’ 18’ 19’ 20’

Cocke County Field House Cocke County, TN

20 psf 16’4” (16’8”) 14’8” (15’0”) 13’5” (13’8”) 12’5” (12’8”) 11’7” (11’11”) 11’0” (11’3”) 10’5” (10’8”) 9’11” (10’2”) 9’6” (9’9”) 9’2” (9’4”) 8’10” (9’0”) 8’6” (8’9”) 8’3” (8’5”) 8’0” (8’2”) 7’9” (7’11”) 7’7” (7’9”) 7’5” (7’7”)

30 psf 13’7” (13’11”) 12’2” (12’5”) 11’1” (11’5”) 10’4” (10’7”) 9’8” (9’10”) 9’1” (9’4”) 8’8” (8’10”) 8’3” (8’5”) 7’11” (8’1”) 7’7” (7’9”) 7’4” (7’6”) 7’1” (7’3”) 6’10” (7’0”) 6’8” (6’9”) 6’5” (6’7) 6’3” (6’5”) 6’1” (6’3”)

40 psf 11’10” (12’2”) 10’8” (10’11”) 9’9” (9’11”) 9’0” (9’3”) 8’5” (8’7”) 7’11” (8’2”) 7’6” (7’9”) 7’2” (7’4”) 6’10” (7’1”) 6’7” (6’9”) 6’5” (6’9”) 6’2” (6’4”) 6’0” 6’1”) 5’9” (5’11”) 5’8” (5’9”) 5’6” (5’7”) 5’4” (5’6”)

5

SUPERIOR METAL PRODUCTS LLC email: [email protected]

Call Toll Free: 1.877.445.1200 • Fax: 1.205.945.5694 TYPICAL APPLICATIONS TYPICAL MECHANICAL BENT 2" DIA. DRAIN HOLE (FIELD-DRILLED)

GUTTERBEAM ANGLE (EXT. ALUM. WITH 3/8" BOLT ASSY.)

#8 X 1/2" TEKS

1/8" EXT. ALUM.

6" X 3" DRAIN BEAM

7" X 3" GUTTER

MITRED CORNER CORNER ANGLES

3/8" SHIMS

BEAM ENDCAP (EXT. ALUM.)

4" X 4" POST

5-1/2" EXTRUDED ALUMINUM GUTTER CORNERS. ( MITERED 45 degrees)

3/8" X 1-1/2"

BOLT ASSEMBLY

TYPICAL COLUMN @ FASCIA

OPTIONAL FASCIA EXTENDER

7 /8

RS CE

LOCKING CLIPS (CENTERED ON EACH CAP) CAP

3/8" x 1-1/2" BOLT ASSY.

2" DIA. DRAIN HOLE (FIELD-DRILLED) ON DRAIN POST ONLY

4" X 4" POST

(NOTCHED & DRILLED BY CANOPY MFR. SEAL WITH SILICONE SEALANT)

TYPICAL BLOCKOUT

PAN

3" DEEP DECK

BOX OUT DETAIL INSTALLER TO SEAL JOINT BETWEEN GUTTER & DOWNSPOUT WATERTIGHT.

4" X 4" ALUMINUM COLUMN DRAIN HOLE (FIELD CUT) & DEFLECTOR PLATE.

EXISTING BUILDING DOWNSPOUTS

8" X 8" X 12" BLOCKOUTS

SHOP-FABRICATED GUTTER SECTIONS TO FRAME AROUND DOWNSPOUTS. (CONTRACTOR TO PROVIDE SIZE(S) OF DOWNSPOUTS.

CANOPY INSTALLER TO GROUT COLUMN INTO BLOCKOUT.

5-1/2" X 3" GUTTER SPLICE (1 EACH SIDE OF BOX-OUT)

BOX-OUT DETAIL ( 5-1/2" x 3" FASCIA / GUTTER )

REBAR

6

7" X 3" GUTTER

EXTRUDED ALUMINUM CORNER ANGLES

PA "S

4' CENTERS #8 X 1/2" TEKS ( TYPICAL @ 2' C/C )

13"

7" X 3" .094

EXT. GUTTER (MITERED 45 degrees)

6" X 1" FASCIA EXTENDER

1" WIDE SUPPORT BRACKET ( TYPICAL @ 4' C/C )

Aluminum Canopies and Walkway Covers

ROLLFORMED CANOPY ASSEMBLY OVERHEAD SUPPORT W-PAN (ROLL-FORMED)

ST RU TE NS IO N

#8 X 1/2" TEKS

PAINTED HEAD

IN IN SER TO T CO FAS RN CI ER A 2 -

1/2

1/4" X 3/4"

"

UPPER WALL BRACKET

T

LOCKING CLIP AT EACH PAN INTERLOCK

BOLT ASSY. DRAIN SCUPPERS (AS REQ'D)

#8 X 1/2" TEKS PAINTED HEAD

FASCIA/GUTTER BRACKET

C

NOTE: DOWNSPOUTS AVAILABE IN 10' LENGTHS ON REQUEST.

3" X 3" 14 GA.

RU ST

T

LOWER WALL BRACKET LOCKING CLIPS ( TYPICAL AT EACH INTERLOCK )

7" EXTRUDED

N PA W-

3/8" X 4"

STEEL COLUMN

S ES PR OM

N IO

BOLT ASSY.

CORNER ANGLES

CANOPY ASSEMBLY ECONO DECK FASCIA/ GUTTER

LOCKING CLIPS

DRAIN SCUPPER

#8 X 1/2"

PAINTED TEKS 18" INTERNAL FASCIA SPLICE FASCIA/GUTTER (MITERED 45∞)

#8 X 1/2"

7/8" SPACERS

PAINTED TEKS .125 EXTRUDED CORNER ANGLES 3/8" X 1-1/2" BOLT ASSY.

4" X 4" .125 COLUMN

X 7"

T. EX

R TE

FLUSH DECK ASSEMBLY

(FACTORY-NOTCHED & DRILLED, SEAL WITH SILICONE SEALANT)

CANOPY INSTALLER TO GROUT COLUMN INTO BLOCKOUT

3"

UT A/G CI S FA

ALUMINUM DECKING

DRAIN HOLE & DEFLECTOR

8" X 8" X 12"

COLUMN ANCHOR

BLOCKOUT (BY OTHERS)

GABLE CROSS SECTION

RID

4"

X4

GE C

"T

ON NE

UB

CT OR

7'' X 3" X .094 EXTRUDED FASCIA/GUTTER

DRAIN HOLE

ALUMINUM BRACKET

E

DRAIN HOLE

3/8'' SHIMS

BEAM CAP

ENDCAP

FL AT -

GUTTER

PA N

ALUMINUM COLUMN (FACTORY-NOTCHED & DRILLED, SEAL WITH SILICONE SEALANT)

6

4 "X

E

UB "T

1/4" CONNECTOR PLATES W/ 1/2" THRU BOLTS

6" X 4-1/2" POST 1/2" X 5-1/2"

BOLT ASSEMBLY

DRAIN HOLE & DEFLECTOR

3/8'' X 1-1/2'' BOLT ASSY.

8'' X 8'' X 12'' BLOCKOUT

COLUMN ANCHOR

7

SCREEN ENCLOSURES

CARPORTS & PATIO COVERS •

overs Patio C rts and Y r CarpoFILES OF QUALIT o ri e p Su PRO

io or r pat y you d patio Enjo screene is needs. tion cific ers to r spe io cov h installa for you and pat eac igned d and ports er, des ical car are use o Cov nom terials . or Pati From eco lity ma port . sfaction qua um Car mer’s sun the finest your sati Alumin the sum gutter. only to ensure an ia/ ms, fasc under at from d sunroo tomized uded cover r car/bo cus or extr Take insulate you and ormed ts. protect losures anceum rollf l pos nten enc Alumin um or stee of mai years Alumin h for your nt finis ted to n pai fabrica neys, Baked-o uty. d and d chim bea igne oun des free tom s, surr is cus corner cover ds: turn ry all. finish. Eve do it lar nee l and particu stairs: we g materia livin ty on protect , add rran perty. Wa furniture r pro ited oor you r Lim outd ance 10 yea s and , enh vehicle weather your ed from Protect protect space

Aluminum rollformed or extruded fascia/gutter.

Individually designed for your home.

•

Baked-on paint finish for years of maintenance free beauty.

•

10 year Limited Warranty on material and finish.

•

Every cover is custom designed and fabricated to your particular needs. Protect your vehicles and outdoor furniture.

SUPERIOR ULTRAVIEW™ SUNROOMS • •

• •

•

Custom designed for your home and landscape. Vinyl horizontal sliding windows feature double-pane insulated and tempered safety glass. Baked enamel aluminum framing for low maintenance. Both window sashes are removable and operate left to right and right to left. Insulated walls tested up to 147 MPH wind speeds. panels provide R-15 thermal rating.

•

3-1/4” thick insulated wall

•

Roof panel has R-13 Thermal Resistance value for energy savings.

•

10 year Warranty on enclosure and Lifetime Warranty on glass breakage and prolonged internal fogging.

•

Optional fan beam allows for installation of fan and/or light fixture.

•

Wall panels available in white or tan fiberglass and white or tan Smooth textured aluminum. • Electrical baseway system available.

•

Aluminum flat pan roof panels for beauty and strength.

•

Your choice of 18”aluminum kickplates or none.

•

Aluminum 2”X 2” horizontal rail, wall studs and corner posts for strength.

•

1” x 2” Pickett system available

Citatio n Scre en Enc PRO FILE losure SO FQ s UALI TY

Exp and you sun’s harsh r enjoya patio ble living enclosurays and res and annoyi area wit ng ha insu lated flies and Citation sunroo mosqu Scr ms, itoes. een Enc custom only losu From ized the fine economre. Kic st qua k-b to ens lity ma ical car ack and ure your por satisfa terials are ts and relax, pro patio tected ction. used cov from and each ers to installa screen ed tion Individ is ually design Alumin ed for um flat you Qualit pan r hom roof y Phi e. pan fer cha els for You r cho rcoal bea ice fibe uty of 18 rgla and Alumin ss scre ” alu strengt posts um 2” minum ening. h. for stre x 2” kick plate ngth. horizo Ava or no ntal ilab le in rail, kick wall Wh plate. Option ite, stud Bronze s and al ava ilab 3” Insu , Tan corner le in , and Wh lated roo 1” x Cre ite, am Cre f Panels, and 2” Pic colors am, Bronze ket Sys and . Tan colors tem ava colors . ilab . le in Wh ite

the

•

•

•

MEDALLION SUNROOMS Superior Medallion Sunrooms

•

Insulated, tempered glass– standard for safety!

•

Each window is a full 5’ high for expanded viewing area.

•

Both window sashes operate right to left and left to right.

•

Both window sashes are removable.

•

3-inch roof has R-13 Thermal Resistance value for energy savings.

PROFILES OF QUALITY Let the sun shine in! Enjoy additional living space at a fraction of the cost by adding a Superior Medallion Sunroom, with insulated roof and walls, to your home. From economical carports and patio covers to screened patio enclosures and insulated sunrooms, only the finest quality materials are used and each installation is customized to ensure your satisfaction.

Insulated, tempered glass-standard for safety! Each window is a full 5’ high for expanded viewing area. Both window sashes operate right to left and left to right. Both window sashes are removable. Roof has R-13 Thermal Resistance value for energy savings. Optional fan beam allows for installation of fan and/or light fixture. 2” thick insulated wall panels provide R-8.5 thermal rating. 10 year Warranty on enclosure and Lifetime Warranty on glass breakage and prolonged internal window fogging.

•

Optional fan beam allows for installation of fan and/or light fixture.

•

2” thick insulated wall panels provide R-9 thermal rating.

•

10 year Warranty on enclosure and Lifetime Warranty on glass breakage and prolonged internal window fogging.

•

All structural components constructed from 6063 T5 aluminum alloy with baked on enamel paint.

•

Electrical baseway system available.

Tempered glass kickplates and transoms available.

STORM AND SCREEN DOORS •

1978 - 2012

35

MADE WITH PRIDE IN THE USA

VINYL WINDOWS

Full 1-1/4” thick extruded aluminum mainframe.

•

1/8” or 3/16” tempered safety glass.

•

Enamel finish: bronze, cream, white or tan.

•

Solid brass hardware, lever latch, keyed deadbolt (outside) thumb turn bolt (inside).

•

Five heavy duty self lubricating hinges with bronze bushings.

•

Brass-tone adjustable bottom expander with vinyl sweep.

•

Optional platinum hardware available.

•

• All welded frame, welded sashes. • LoE 3-366 glass and Argon Gas filled - Standard. • 3/4” sealed insulated glass with DuraSeal™ spacer. • Double Hung sashes tilt in and Slider sashes remove for safe, easy cleaning from inside. • Limited Lifetime Warranty. • Available in white and beige. • Energystar qualified-all 50 states All windows are custom manufactured to your exact measurements to ensure a perfect fit and care free operation.

SUPERIOR METAL PRODUCTS LLC

®

116 Citation Court Birmingham, Alabama 35209-6307 Toll Free: 1.877.445.1200 • fax: 205.945.5694 email: [email protected]

Printed in the U.S.A.