SPECIFICATION FOR LCD MODULE MODULE NO: YB-YG320240S16A-C-A0

YEEBO LCD Limited LCM Specialist SPECIFICATION FOR LCD MODULE MODULE NO: YB-YG320240S16A-C-A0 Doc.Version:00 Customer Approval: □ Accept □ Reject ■...
Author: Tyrone Craig
1 downloads 2 Views 891KB Size
YEEBO LCD Limited LCM Specialist

SPECIFICATION FOR LCD MODULE MODULE NO: YB-YG320240S16A-C-A0 Doc.Version:00 Customer Approval: □ Accept

□ Reject

■APPROVAL FOR SPECIFICATIONS ONLY □APPROVAL FOR SPECIFICATIONS AND SAMPLE WIMRD005-02-C

Add: 7/F.,On Dak Industrial Building,2-6 Wah Sing Street, Kwai Chung,H.K. Tel: +852-2945-6800 ; +852-2945-6885 Fax: +852-2481-0019

YEEBO LCD Limited LCD,LCM Specialist

1. Revision History Sample Version

DOC. Version

DATE

A0

00

2014-04-25

DESCRIPTION SPEC ONLY

First issue

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

CHANGED BY Calamie / Gavin

1

YEEBO LCD Limited LCD,LCM Specialist

2. Table of Contents: NO

CONTENTS

PAGE

1

Revision History

1

2

Table of Contents

2

3

Module Numbering System

3

4

General Specification

4

5

LCM drawing

5

6

Electrical Characteristics

6

7

Optical Characteristics

14

8

Interface Pin Assignment

16

9

Block Diagram

18

10

Backlight

19

11

Standard Specification for Reliability

20

12

Specification of Quality Assurance

22

13

Handing Precaution

30

14

Guarantee

30

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

2

YEEBO LCD Limited LCD,LCM Specialist

3. Module Numbering System: (Example)

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

3

YEEBO LCD Limited LCD,LCM Specialist

4. General Specification: ITEM

CONTENTS

Module Size

99.2(W) * 72.4 (H) * 4.1(T) mm

Module Size(With FPC)

99.2(W) *133.95 (H) * 4.1 (T) mm

Display Size(Diagonal)

3.5 inch

Display Format

320(RGB)* 240 Pixels

Active Area

70.08(W) *52.56(H) mm

Pixel Pitch

0.219mm*0.219 mm

LCD Type

TFT (262K)/ Transmissive / NW

Touch panel Type

OLS/ Cover glass

View Angle

12 O’clock

CTP IC

ILI2830

Controller IC

HX8238-D

Weight

TBD

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

4

YEEBO LCD Limited LCD,LCM Specialist

5. LCM drawing:

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

5

YEEBO LCD Limited LCD,LCM Specialist

6. Electrical Characteristics 6-1 Absolute Maximum Ratings TFT IC HX8238-D Parameter Item

Symbol

Min.

Type

Max.

Unit

Remark

Input Voltage

VCI-VSS

-0.3

-

+5.0

Volt

Note1

Supply Voltage

VDDIO-VSS

-0.3

-

+4.0

Volt

Note1

Operating Temperature

Topr

-10

-

+70



-

Storage Temperature

Tstg

-30

-

+80



-

Note1: Absolute maximum rating is the limit value beyond which the IC maybe broken. They do not assure operations.

Touch panel controller ILI2839 Parameter Item

Symbol

Min.

Type

Max.

Unit

Humidi ty

Supply Voltage

VDD

-0.3

-

+3.6

V

Note1

Digital power supply voltage

VDDD

-0.3

-

+1.98

I/O power supply Voltage

VDDIO

Note1

V Note1 -0.3 +3.6 Note1: Absolute maximum rating is the limit value beyond which the IC maybe broken. They do not assure operations.

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

6

YEEBO LCD Limited LCD,LCM Specialist

6-2 Operating Conditions TFT IC HX8238-D Characteristics Item Power Supply voltage

(Ta=25℃ )

Symbol

Condition

Min.

Typ.

Max.

Unit

VCI-VSS

-

2.6

2.8

3.0

Volt

VIH

-

0.8 * VDDIO

-

VDDIO

V

VIL

-

VSS

-

0.2 * VDDIO

V

IDD

VCI=2.8V

-

8

-

mA

Input Voltage

Power Supply Current for LCM

Touch panel controller ILI2839 Characteristics Item

Symbol

Condition

Min.

Typ.

Max.

Unit

Power Supply

VDD

-

2.6

3.3

3.6

Vt

VIH

-

-

VDDIO

V

VIL

-

Input Voltage

Output Voltage

0.7 * VDDIO -0.3

-

VOH

VDDIO

VOL

0.3

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

0.3* VDDIO

V

V

7

YEEBO LCD Limited LCD,LCM Specialist

6-3 Timing Characteristics TFT IC HX8238-D Pixel Timing

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

8

YEEBO LCD Limited LCD,LCM Specialist

Data Transaction Timing in Parallel RGB Interface (SYNC Mode)

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

9

YEEBO LCD Limited LCD,LCM Specialist

Data Transaction Timing in Parallel RGB Interface (DE Mode)

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

10

YEEBO LCD Limited LCD,LCM Specialist

Write SPI

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

11

YEEBO LCD Limited LCD,LCM Specialist

Read SPI

SPI Time

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

12

YEEBO LCD Limited LCD,LCM Specialist

Touch panel controller ILI2830 Item 7-1 Supply voltage for logic 7-2 Supply current for logic 7-3 Insulation resistance 7-4 Linearity 7-5 Chattering 7-6 Timing Characteristics

Specification Symbol Min Typ Max VDD 2.6 3.3 3.6 Symbol Min Typ Max IDD ≧20M Ω(DC 25V) ≦3.0% ≦15ms

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

Unit V Unit mA

Remarks Use Linear Teste -

13

YEEBO LCD Limited LCD,LCM Specialist

7. Optical Characteristics: Item

Symbol

Conditions

Transmittance (Without PL)

T(%)

-

Contrast Ratio

CR

Response time

TR+TF Θx+ ΘxΘy+ Θy-

Viewin g angle

Hor. Ver.

Θ=0 Normal Viewing angle CR≧10

Specifications Min Typ Max -

7.4

-

200

300

-

-

50 45 45 45 45

80 -

Unit

Note

-

(1) (2)

ms

(1) (3)

deg.

-

Measuring Condition 1. Measuring surrounding: dark room 2. Ambient temperature: 25±2℃ 3. 30 min. Warm-up time.

Color of CIE Coordinate: Item

Symbol Red

Chromaticity

Green

Coordinates (Transmissive)

Blue White

x y x y x y x y

Condition θ = 0° LED Backlight Color Degree X=0.26 Y=0.26 Brightness =TBD Cd/m2

Min.

Typ.

Max.

-

0.6155

-

-

0.3673

-

-

0.3386

-

-

0.5901

-

-

0.2966

-

-

0.3099

-

-

0.2966

-

-

0.3099

-

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

Brightness TBD Cd/m2 TBD Cd/m2 TBD Cd/m2 TBD Cd/m2

14

YEEBO LCD Limited LCD,LCM Specialist

Note (1) Definition of Viewing Angle :

Note (2) Definition of Contrast Ratio(CR) : measured at the center point of panel

Note (3) Definition of Response Time : Sum of TR and TF

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

15

YEEBO LCD Limited LCD,LCM Specialist

8. Interface Pin Assignment: TFT Interface Pin No.

Symbol

Function

1

LED-

Power Supply for Backlight.

2

LED-

Power Supply for Backlight.

3

LED+

Power Supply for Backlight.

4

LED+

Power Supply for Backlight.

5

GND

Power Ground.

6

NC(XR)

Open.

7

NC(YD)

Open.

8

NC(XL)

Open.

9

NC(YU)

Open.

10

GND

11

NC

Open.

12

NC

Open.

13

NC

Open.

14

RESET

15

CS

16

SCL

Clock pin of serial interface.- Leave it OPEN when mot use.

17

SDI

Data input pin in serial mode.-Leave it OPEN when mot use.

18

NC

Open.

19

NC

Open.

20

DATA0

21

DATA1

22

DATA2

23

DATA3

24

DATA4

25

DATA5

26

NC

Open

27

NC

28

DATA6

29

DATA7

Open Green Data Input Pins. --If not use pins,plese connect to GND.

30

DATA8

31

DATA9

Power Ground.

System reset pin. Internal pull high.- Connect to VDDIO when not used Chip select pin of serial interface.-Leave it OPEN when mot use.

Blue Data Input Pins. -- If not use pins,plese connect to GND.

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

16

YEEBO LCD Limited LCD,LCM Specialist

32

DATA10

33

DATA11

34

NC

Open.

35

NC

Open.

36

DATA12

37

DATA13

38

DATA14

39

DATA15

40

DATA16

41

DATA17

42

HSYNC

Horizontal Sync Input.

43

VSYNC

Vertical Sync Input.

44

DOTCLK

45

NC

Open.

46

NC

Open.

47

VCI

Power Supply.

48

VCI

Power Supply.

49-57

NC

Open.

58

ENABLE

59

GND

Power Ground.

60

GND

Power Ground.

Red Data Input Pins. --If not use pins,plese connect to GND.

Dot Data Clock.

Display enable pin from controller.

CTP Interface Pin No.

Symbol

Function

1

VDD

2

RESET

3

INT

External interrupt pin to host.

4

SCL

Serial clock pin for I2C interface.

5

SDA

Serial data pin for I2C interface.

6

GDN

Ground.

Analog power supply. RESET.

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

17

YEEBO LCD Limited LCD,LCM Specialist

9. Block Diagram: .

LCD PANNEL Back Light

CTP ILI2839

320(RGB) X 240 PIXELS

HX8238-D .

CTP 6 PIN Interface

TFT 60 PIN Interface .

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

.

18

.

YEEBO LCD Limited LCD,LCM Specialist

10. Backlight: 1. Standard Lamp Styles (Edge Lighting Type): The LED chips are distributed over the edge light area of the illumination unit, which gives the less power consumption: 2. The Main Advantages of the LED Backlight are as following: 2.1 The brightness of the backlight can simply be adjusted. By a resistor or a potentiometer. 3. Data About LED Backlight: PARAMETER

Sym.

Min.

Typ.

Max.

Unit

Supply Current Supply Voltage Reverse Voltage Luminous Intensity for LCM Uniformity for LCM Life Time

I V VR

-

15 19.2 -

5.0

mA V V

IV

-

200

-

Cd/m2

-

70 20000

-

% Hr.

Color

Test Condition V=19.2V If=15mA If=15mA If=15mA

Note

2 3 4

White

NOTE: 1. Backlight Only 2. Average Luminous Intensity of P1-P9 3. Uniformity = Min/Max * 100% 4. LED life time defined as follows: The final brightness is at 70% of original brightness Measured Method: (X*Y: Light Area)

Internal Circuit Diagram

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

19

YEEBO LCD Limited LCD,LCM Specialist

11. Standard Specification for Reliability: 11 - 1 Standard Specifications for Reliability of LCD Module No

Item

Description

01

High temperature operation

The sample should be allowed to stand at 70℃ for 120 hours under driving condition and then returning it to normal temperature condition, and allowing it stand for 2 hours.

02

Low temperature operation

The sample should be allowed to stand at -20℃ for 120 hours under driving condition and then returning it to normal temperature condition, and allowing it stand for 2 hours.

03

High temperature storage

The sample should be allowed to stand at 80℃ for 240 hours under no-load condition, and then returning it to normal temperature condition, and allowing it stand for 2 hours.

04

Low temperature storage

The sample should be allowed to stand at -30℃ for 240 hours under no-load condition, then returning it to normal temperature condition, and allowing it stand for 2 hours.

05

Moisture storage

The sample should be allowed to stand at 60℃,90%RH MAX for 240 hours under no-load condition, then taking it out and drying it at normal temperature for 2 hours.

06

Thermal shock storage

The sample should be allowed to stand the following 10 cycles : -30℃ for 30 minutes → normal temperature for 5 minutes → +80℃ for 30 minutes → normal temperature for 5 minutes, as one cycle.

07

Packing vibration

Frequency range : 10Hz ~ 55Hz Amplitude of vibration : 1.5mm X,Y,Z 2 hours for each direction.

08

Packing drop test

According to ISTA 1A 2001.

Sweep time: 12 min

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

20

YEEBO LCD Limited LCD,LCM Specialist

09

Electrical Static Discharge

Air: ±4KV 150pF/330Ω 5 times Contact: ±2KV 150pF/330Ω 5 time

*Sample size for each test item is 3~5pcs 11 - 2. Testing Conditions and Inspection Criteria For the final test the testing sample must be stored at room temperature for 24 hours, after the tests listed in Table 11-1, Standard specifications for Reliability have been executed in order to ensure stability. No

Item

Test Model

In section Criteria

01

Current Consumption

Refer To Specification

The current consumption should conform to the product specification.

02

Contrast

Refer To Specification

After the tests have been executed, the contrast must be larger than half of its initial value prior to the tests.

03

Appearance

Visual inspection

Defect free.

11- 3. MTBF

MTBF

Functions, performance, appearance, etc. shall be free from remarkable deterioration within 50,000 hours under ordinary operating and storage conditions room temperature (25±5℃), normal humidity (50±10% RH), and in area not exposed to direct sun light.

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

21

YEEBO LCD Limited LCD,LCM Specialist

12. Specification of Quality Assurance: 12-1. Purpose This standard for Quality Assurance should affirm the quality of LCD module products to supply to purchaser by YEEBO CORPORATION (Supplier). 12-2. Standard for Quality Test a. Inspection: Before delivering, the supplier should take the following tests, and affirm the quality of product. b. Electro-Optical Characteristics: According to the individual specification to test the product. c. Test of Appearance Characteristics: According to the individual specification to test the product. d. Test of Reliability Characteristics: According to the definition of reliability on the specification for testing products. e. Delivery Test: Before delivering, the supplier should take the delivery test. (i) Test method: According to MIL-STD105E.General Inspection Level Ⅱ take a single time. (ii) The defects classify of AQL as following: Major defect: AQL = 0.65 Minor defect: AQL = 2.5 Total defects: AQL = 2.5 12-3. Non- conforming Analysis & Deal With Manners a. Non- conforming Analysis: (i) Purchaser should supply the detail data of non- conforming sample and the nonconforming. (ii) After accepting the detail data from purchaser, the analysis of non- conforming should be finished in two weeks. (iii) If supplier can not finish analysis on time, must announce purchaser before 3 days. b. Disposition of non- conforming: (i) If find any product defect of supplier during assembly time, supplier must change the good product for every defect after recognition. (ii) Both supplier and customer should analyze the reason and discuss the disposition of non- conforming when the reason of nonconforming is not sure. 12-4. Agreement items Both sides should discuss together when the following problems happen. a. There is any problem of standard of quality assurance, and both sides should think that must be modified. b. There is any argument item which does not record in the standard of quality assurance. c. Any other special problem.

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

22

YEEBO LCD Limited LCD,LCM Specialist

12-5. Standard of The Product Appearance Test a. Manner of appearance test: (i) The test must be under 20W × 2 or 40W fluorescent light, and the distance of view must be at 30±5cm. (ii) When test the model of transmissive product must add the reflective plate. (iii)The test direction is base on around 10° of vertical line. (iiii)Temperature: 25±5℃ Humidity: 60±10%RH eyes eyes 10° 10°

(iv) Definition of area:

A B

A. Area: Viewing area. B. Area: Out of viewing area. (Outside viewing area) b. Basic principle: (i) It will accord to the AQL when the standard can not be described. (ii) The sample of the lowest acceptable quality level must be discussed by both supplier and customer when any dispute happened. (iii) Must add new item on time when it is necessary. c. Standard of inspection: (Unit: mm)

Module P/N: YB-YG320240S16A-C-A0 Doc.Version:00

23

YEEBO LCD Limited LCD,LCM Specialist

12-6. Inspection specification NO Item Criterion 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character, dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. Electrical 01 1.6 LCD viewing angle defect. Testing 1.7 Flicker

02

Black or 2.1 White and black or color spots on display ≦ 0.25mm, no more than White spots Five spots. or Bright 2.2 Densely spaced: No more than three spots within 3mm. spots or Color spots on LCD (Display only) 3.1 Round type: As following drawing Φ = (X+Y) / 2 Size(mm) Φ≦0.20 0.20< Φ≦0.40 0.40< Φ

03

LCD and Touch Panel black spots, white spots, contamination (non – display)

Acceptable Q'ty Accept no dense 5 0

AQL

0.65

2.5

2.5

* Densely spaced: No more than two spots within 3mm. 3.2 Line type: (As following drawing) Length( mm)

Width(mm)

Acceptable Q'ty

W≦0.05

Accept no dense 5 Rejection

L≦3.0 L>3.0

0.05