YEEBO LCD Limited LCM Specialist
SPECIFICATION FOR LCD MODULE MODULE NO: YB-TG1024600S07A-N-A0 Doc.Version:01 Customer Approval: Accept
Reject
APPROVAL FOR SPECIFICATIONS ONLY APPROVAL FOR SPECIFICATIONS AND SAMPLE WIMRD005-02-C
Add: 7/F.,On Dak Industrial Building,2-6 Wah Sing Street, Kwai Chung,H.K. Tel: +852-2945-6800 ; +852-2945-6885 Fax: +852-2481-0019
YEEBO LCD Limited LCD,LCM Specialist
1. Revision History Sample Version
DOC. Version
DATE
A0
00
2013-12-31
A0
01
2014-03-26
DESCRIPTION FULL SPEC
FULL SPEC
First issue Update item 1.Update Viewing Direction and Weight P.4 2 Update: 7. Optical Characteristics: P10 3.Update NO. of the contents: No11,12,13,14 P15~P25
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
CHANGED BY Alex / Aching
Alex / Aching
1
YEEBO LCD Limited LCD,LCM Specialist
2. Table of Contents: NO
CONTENTS
PAGE
1
Revision History
1
2
Table of Contents
2
3
Module Numbering System
3
4
General Specification
4
5
LCM drawing
5
6
Electrical Characteristics
6
7
Optical Characteristics
10
8
Interface Pin Assignment
12
9
Block Diagram
13
10
Backlight
14
11
Standard Specification for Reliability
15
12
Specification of Quality Assurance
17
13
Handling Precaution
25
14
Guarantee
25
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
2
YEEBO LCD Limited LCD,LCM Specialist
3. Module Numbering System: (Example)
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
3
YEEBO LCD Limited LCD,LCM Specialist
4. General Specification: ITEM
CONTENTS
Module Size
170.0(W) * 105.2(H) * 11.2(T) mm
Display Size (Diagonal)
7.0 inch
Display Format
1024(RGB)* 600 Pixels
Active Area
153.6 (W) * 90.0 (H) mm
Dots Pitch
0.15* 0.15
mm
LCD Type
TFT (16.7M)/ Transmissive / Normal White /Anti-Glare
TFT Interface
LVDS
Viewing Direction
6 O’clock
Weight
210g ( max )
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
4
YEEBO LCD Limited LCD,LCM Specialist
5. LCM drawing: Front Side
Back Side
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
5
YEEBO LCD Limited LCD,LCM Specialist
6. Electrical Characteristics 6-1 Absolute Maximum Ratings
(Ta=25
Item
Symbol
Min.
Type
Max.
Unit
Power Supply voltage
VDD
3.0
-
3.6
Volt
VLED
8.0
16.0
Volt
IFUSE
-
1.5
A
PWM Voltage
VPWM
0.8
5.0
Volt
Operating Temperature
Topr
-30
Operating Humidity
Hopr
10
Storage Temperature
Tstg
-40
LED Backlight Drive Voltage Power Supply Fuse Current Setting
-
Remark
+85 +85
-
VSS=0V)
%RH
+95
Storage Humidity Hstg 10 +95 %RH Note: Absolute maximum rating is the limit value beyond which the IC maybe broken.
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
6
YEEBO LCD Limited LCD,LCM Specialist
6-2 Operating Conditions Item
(Ta=25
Symbol
Power Supply voltage
VDD
)
Condition
Min.
Typ.
Max.
Unit
-
3.0
3.3
3.6
V
Input Inrush Current
IRUSH
1.5
A
Input Power Voltage Ripple
VRPL
200
mV
100
mV
LVDS Signals Differential Input High Threshold Differential Input Low Threshold Magnitude Differential Input Voltage Common Mode Voltage Common Mode Voltage Offset Power Supply Current for LCM Power Consumption
Vth Vtl
-100
|Vid|
200
Vcm
1.0
1.2
-50
Vcm IDD
mV
-
-
-
PBLACK
600
mV
1.4
V
50
mV
(153)
mA
(0.573)
W
Back Light Control signals LED Input Voltage
VLED
8
12
(16)
V
LED Power Consumption
PLED
-
-
(5.04)
W
High
2.0
3.3
5
V
Low
0
0.8
V
High
2.0
5
V
Low
0
0.8
V
(200)
1000
Hz
Duty Ratio PWM_DR 5 100 Note: A. Input signals shall be low or Hi-Z state when B. All electrical characteristics for LVDS signal interface connector of LCD. C. White Pattern at 3.3V driving voltage.
%
PWM Signal Voltage &
VPWM_EN
LED Enable Voltage
VLED_EN
Input PWM Frequency
FPWM_F
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
3.3
7
YEEBO LCD Limited LCD,LCM Specialist
6-3 Display Data Input Timing 6-3-1 Timing Characteristics
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
8
YEEBO LCD Limited LCD,LCM Specialist
6-4 Power ON/OFF Sequence
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
9
YEEBO LCD Limited LCD,LCM Specialist
7. Optical Characteristics: Item
Symbol
Conditions
Transmittance
T(%)
-
Contrast Ratio
CR
=0 Normal Viewing angle -
Response time
TR+TF x+ Hor. xViewing CR 10 angle y+ Ver. yMeasuring Condition 1. Measuring surrounding: dark room 2. Ambient temperature: 25±2 3. 30 min. Warm-up time.
Specifications Min Typ Max (3.5%) -
(700)
(800)
-
(70) (70) (70) (70)
16 (75) (75) (75) (75)
25 -
Unit
Note
-
-
(1) (2)
ms
(1) (3)
deg.
-
Color of CIE Coordinate: Item Red Chromaticity
Green
Coordinates (Transmissive)
Blue White
Symbol
Min.
Typ.
Max.
x
0.598
0.628
0.658
y
0.328
0.358
0.388
x
0.277
0.307
0.337
y
0.596
0.626
0.656
x
0.120
0.150
0.180
y
0.017
0.047
0.077
x
0.255
0.305
0.355
y
0.275
0.325
0.375
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
10
YEEBO LCD Limited LCD,LCM Specialist
Note (1) Definition of Viewing Angle :
Note (2) Definition of Contrast Ratio(CR) : measured at the center point of panel
Note (3) Definition of Response Time : Sum of TR and TF
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
11
YEEBO LCD Limited LCD,LCM Specialist
8. Interface Pin Assignment: 8-1 TFT Interface No.
Symbol
Function
1
VDD
Power Voltage for digital circuit
2
VDD
Power Voltage for digital circuit
3
VSS
Power Ground
4
REV
Reverse Scan selection, 3.3V ( typ.)
5
Rin1-
-LVDS differential data input (R0-R5,G0)
6
Rin1+
+LVDS differential data input (R0-R5,G0)
7
VSS
Power Ground
8
Rin2-
-LVDS differential data input(G1-G5,B0-B1)
9
Rin2+
+LVDS differential data input(G1-G5,B0-B1)
10
VSS
Power Ground
11
Rin3-
-LVDS differential data input (B2-B5,HS,VS,DE)
12
Rin3+
+LVDS differential data input (B2-B5,HS,VS,DE)
13
VSS
Power Ground
14
CLKIN-
-LVDS differential clock input
15
CLKIN+
+LVDS differential clock input
16
VSS
Power Ground
17
Rin4-
-LVDS differential data input (R6,R7,G6,G7,B6,B7)
18
Rin4+
+LVDS differential data input (R6,R7,G6,G7,B6,B7)
19
VSS
Power Ground
20
NC
Test pin for internal function , Float the pin .
8-2 Black Light Interface No. 1
Symbol
Function
VLED
Power Supply, 12V (Typ.)
2
GND
Ground
3
EN
3.3V (Typ.)
4
PWM
3.3V (Typ.)
5
NC
Not Connection
8-3Connector Name / Designation Manufacturer
STM(or equivalent)
LVDS Connector
MSB240420HD
BL Connector
MSB24038P5A
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
12
YEEBO LCD Limited LCD,LCM Specialist
9. Block Diagram:
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
13
YEEBO LCD Limited LCD,LCM Specialist
10. Backlight: Data About LED Backlight: PARAMETER
Sym.
Min.
Typ.
Max.
Unit
Note
Supply Current
If
-
80
-
mA
4.
Supply Voltage
Vf
3.0
3.3
3.6
V
4.
Luminous Intensity for LCM
LV
400
500
-
Cd/m2
1.4.
Uniformity for LCM
-
80
-
-
%
2.4.
Life Time
-
50000
-
-
Hr.
3.4.
NOTE: 1. Average Luminous Intensity of P1-P9 2. Uniformity = Min/Max * 100% 3. The LED life time define as the estimated time to 50% degradation of initial luminous. 4. Operating temperature 2 Measured Method: (X*Y: Light Area)
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
14
YEEBO LCD Limited LCD,LCM Specialist
11. Standard Specification for Reliability : 11–1. Standard Specifications for Reliability of LCD Module No
Item
Description
01
High temperature operation
The sample should be allowed to stand at 85 for hours under driving condition and then returning it to normal temperature condition, and allowing it stand for 2 hours.
02
Low temperature operation
The sample should be allowed to stand at -30 for hours under driving condition and then returning it to normal temperature condition, and allowing it stand for 2 hours.
03
High temperature storage
The sample should be allowed to stand at 95 for 240 hours under no-load condition, and then returning it to normal temperature condition, and allowing it stand for 2 hours.
04
Low temperature storage
The sample should be allowed to stand at -40 for 240 hours under no-load condition, then returning it to normal temperature condition, and allowing it stand for 2 hours.
05
Moisture storage
The sample should be allowed to stand at 60 ,90%RH MAX for 240 hours under no-load condition, then taking it out and drying it at normal temperature for 2 hours.
06
Thermal shock storage
07
Packing vibration
Frequency range : 10Hz ~ 55Hz Amplitude of vibration : 1.5mm X,Y,Z 2 hours for each direction.
08
Packing drop test
According to ISTA 1A 2001.
09
Electrical Static Discharge
The sample should be allowed to stand the following 10 cycles : -40 for 30 minutes normal temperature for 5 minutes +95 for 30 minutes normal temperature for 5 minutes, as one cycle.
Sweep time: 12 min
Air: ±6KV 150pF/330 5 times Contact: ±4KV 150pF/330 5 time
*Sample size for each test item is 3~5pcs
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
15
YEEBO LCD Limited LCD,LCM Specialist
11 - 2. Testing Conditions and Inspection Criteria For the final test the testing sample must be stored at room temperature for 24 hours, after the tests listed in Table 11.1, Standard specifications for Reliability have been executed in order to ensure stability. No
Item
Test Model
In section Criteria
01
Current Consumption
Refer To Specification
The current consumption should conform to the product specification.
02
Contrast
Refer To Specification
After the tests have been executed, the contrast must be larger than half of its initial value prior to the tests.
03
Appearance
Visual inspection
Defect free.
11- 3. MTBF
MTBF
Functions, performance, appearance, etc. shall be free from remarkable deterioration within 50,000 hours under ordinary operating and storage conditions room temperature (25±5 ), normal humidity (50±10% RH), and in area not exposed to direct sun light.
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
16
YEEBO LCD Limited LCD,LCM Specialist
12. Specification of Quality Assurance: 12-1. Purpose This standard for Quality Assurance should affirm the quality of LCD module products to supply to purchaser by YEEBO CORPORATION (Supplier). 12-2. Standard for Quality Test a. Inspection: Before delivering, the supplier should take the following tests, and affirm the quality of product. b. Electro-Optical Characteristics: According to the individual specification to test the product. c. Test of Appearance Characteristics: According to the individual specification to test the product. d. Test of Reliability Characteristics: According to the definition of reliability on the specification for testing products. e. Delivery Test: Before delivering, the supplier should take the delivery test. (i) Test method: According to MIL-STD105E.General Inspection Level take a single time. (ii) The defects classify of AQL as following: Major defect: AQL = 0.65% Minor defect: AQL = 2.5% Total defects: AQL = 2.5% 12-3. Non- conforming Analysis & Deal With Manners a. Non- conforming Analysis: (i) Purchaser should supply the detail data of non- conforming sample and the nonconforming. (ii) After accepting the detail data from purchaser, the analysis of non- conforming should be finished in two weeks. (iii) If supplier can not finish analysis on time, must announce purchaser before 3 days. b. Disposition of non- conforming: (i) If find any product defect of supplier during assembly time, supplier must change the good product for every defect after recognition. (ii) Both supplier and customer should analyze the reason and discuss the disposition of non- conforming when the reason of nonconforming is not sure. 12-4. Agreement items Both sides should discuss together when the following problems happen. a. There is any problem of standard of quality assurance, and both sides should think that must be modified. b. There is any argument item which does not record in the standard of quality assurance. c. Any other special problem.
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
17
YEEBO LCD Limited LCD,LCM Specialist
12-5. Standard of The Product Appearance Test a. Manner of appearance test: (i) The test must be under 20W × 2 or 40W fluorescent light, and the distance of view must be at 30±5cm. (ii) When test the model of transmissive product must add the reflective plate. (iii)The test direction is base on around 10° of vertical line. (iiii)Temperature: 25±5 Humidity: 60±10%RH eyes eyes
A. Area: Viewing area. B. Area: Out of viewing area. (Outside viewing area) b. Basic principle: (i) It will accord to the AQL when the standard can not be described. (ii) The sample of the lowest acceptable quality level must be discussed by both supplier and customer when any dispute happened. (iii) Must add new item on time when it is necessary. c. Standard of inspection: (Unit: mm)
Module P/N: YB-TG1024600S07A-N-A0 Doc.Version:01
18
YEEBO LCD Limited LCD,LCM Specialist
NO
01
12-6. Inspection specification Item Criterion 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character, dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. Electrical 1.6 LCD viewing angle defect. Testing 1.7 Mixed product types. 1.8 Flicker
AQL
0.65
2.1 Dot dimension as below drawing: = (X+Y) / 2
02
Black or White spots or Bright spots or Color spots on LCD (Display only)
Size(mm) 0.20 0.20< 0.40 0.40
10 ----
Width(mm)
Acceptable Q'ty
W 0.1 0.1