COMPREHENSIVE INTERNET SECURITY ™

b

SonicWALL Internet Security Appliances

SonicWALL TZ 190 Wireless Getting Started Guide

SonicWALL TZ 190 Wireless Getting Started Guide

Thank you for your purchase of the SonicWALL TZ 190 Wireless, the ultimate security platform for home and small office deployments. With integrated support for SonicWALL's Gateway Anti-Virus, the SonicWALL TZ 190 Wireless delivers powerful, yet easy-to-use protection against malicious users and viruses. The SonicWALL TZ 190 Wireless security appliance also supports SonicWALL's Content Filtering Service to provide enhanced productivity and network utilization. This Getting Started Guide contains installation procedures and configuration guidelines for deploying a SonicWALL TZ 190 Wireless on your network. For detailed configuration information, refer to the SonicOS Enhanced Administrator’s Guide on the SonicWALL Resource CD or on the Web at: .

SonicWALL TZ 190 Wireless Getting Started Guide Page 1

READ BEFORE CONTINUING Important Information Regarding WWAN Service Providers It is important to understand that not all WWAN service providers operate in the same way or support all the same feature sets. Because of this, there exists some inherent “service provider-specific” variances in service area and more importantly, in supported features. Along with feature limitations may also come certain restrictions such as bandwidth constraints and networking limitations. Before purchasing a WWAN PC card and service plan, check to make sure that the WWAN service provider offers support for the features you need. Before committing to a service contract with a WWAN service provider, it may be helpful to ask these questions: • • • • • • •

What types of traffic are allowed over the WWAN network? Do they offer “static” or “dynamic” IP addressing? Are there any inbound connection limitations? Are single or multiple hosts allowed? Do they support VPN traffic? What are the data transfer limits (inbound and outbound)? What are common data transfer speeds and how much of the coverage area supports 3G or faster technology?

Page 2 READ BEFORE CONTINUING - Important Information Regarding WWAN Service Providers

Document Contents This document contains the following sections: 1

Completing Pre-Configuration Tasks - page 5

2

Preparing Your WWAN PC Card - page 11

3

Registering Your SonicWALL - page 29

4

Connecting for Initial Setup - page 31

5

Running the Setup Wizard - page 37

6

Verifying Your WWAN Connection - page 43

7

Connecting to Your Network - page 47

Appendix Appendix A: Configuring DHCP IP Addressing - page 51 Appendix B: Troubleshooting Internet Connectivity - page 52 Appendix C: Safety Instructions and Regulatory Information - page 53

SonicWALL TZ 190 Wireless Getting Started Guide Page 3

Page 4 READ BEFORE CONTINUING - Important Information Regarding WWAN Service Providers

Completing Pre-Configuration Tasks

1

In this Section: This section provides pre-configuration information. It is necessary to review this section before setting up your SonicWALL TZ 190 Wireless. • • • • •

System Requirements , on page 6 Check Package Contents , on page 7 Obtain Configuration Information , on page 8 Obtain Internet Service Provider (ISP) Information , on page 9 Obtain WWAN Service Provider Information , on page 10

SonicWALL TZ 190 Wireless Getting Started Guide Page 5

System Requirements Before you begin the setup process, check to ensure that you have a computer that meets the following requirements. This computer is used to manage your SonicWALL TZ 190 Wireless during the setup process. • • • •



Windows Vista, Windows XP, Windows 2000 or Windows NT 40MB of disk space available One available 10/100 Ethernet (LAN) port A Web browser supporting Java and HTTP uploads. Internet Explorer 6.0 or higher, Netscape Navigator 4.7 or higher, Mozilla 1.7 or higher are recommended LAN interface set to obtain an IP address automatically (DHCP addressing enabled)

Note: In order to connect to the SonicWALL TZ 190 Wireless, your computer must be set to obtain an IP address automatically using DHCP. For more information on configuring DHCP on your computer, turn to Appendix A: Configuring DHCP IP Addressing , on page 51.

Page 6 System Requirements

Check Package Contents

Any Items Missing? If any items are missing from your package, please contact SonicWALL support.

SonicWALL TZ 190 Wireless Standard power adapter DB9 -> RJ45 (CLI) Cable Wireless antenna pair Ethernet cable SonicWALL Resource CD Getting Started Guide Release Notes document

1 2 3 4 5 6 7 8

A listing of the most current support options is available online at: *The included power cord is intended for use in North America only. For European Union (EU) customers, a power cord is not included.

7

6

1

COMPREHENSIVE INTERNET SECURITY

SonicWALL Resource CD

wwan signal link/act

wan opt

wlan

link/act

WiFiSec on/act

10/100

2

TZ 190

SonicWALL Getting Started Guide

wireless

8 3

SonicOS Release Notes

Contents

4

5

SonicWALL TZ 190 Wireless Getting Started Guide Page 7

Obtain Configuration Information Please record and keep for future reference the following setup information:

Registration Information Serial Number:

Record the serial number found on the bottom panel of your SonicWALL appliance.

Authentication Code:

Record the authentication code found on the bottom panel of your SonicWALL appliance.

Networking Information LAN IP Address: .

.

.

Subnet Mask: .

Record the subnet mask for the local subnet where you are installing your SonicWALL appliance. .

.

Ethernet WAN IP Address: .

Select a static IP address for your SonicWALL appliance that is within the range of your local subnet. If you are unsure, you can use the default IP address (192.168.168.168).

.

.

Select a static IP address for your Ethernet WAN. This setting only applies if you are already using an ISP that assigns a static IP address.

Administrator Information Admin Name:

Select an administrator account name. (default is admin)

Admin Password:

Select an administrator password. (default is password)

Page 8 Obtain Configuration Information

Obtain Internet Service Provider (ISP) Information Record the following information about your current Internet service: If you connect via

You likely use

Please record

Cable modem, DSL with a router

DHCP

No Internet connection information is usually required, although some service providers require a host name. Host Name:

Home DSL

PPPoE

User Name: Password: Note: Your ISP may require your user name in the format: [email protected]

T1/E1, Static broadband, Cable or DSL with a static IP

Static IP

IP Address: . Subnet Mask: . Default Gateway (Router IP Address): Primary DNS: . Secondary DNS . (optional):

Dial-in to a server

PPTP

.

. .

.

. .

.

. .

. .

Server Address: User Name: Password:

SonicWALL TZ 190 Wireless Getting Started Guide Page 9

Obtain WWAN Service Provider Information Record the following information about your current WWAN service:

WWAN Service Provider Country:

Record the country where you purchased your WWAN card.

Service Provider:

Record the service provider from whom you purchased your WWAN card. This is the brand name of the card.

Plan Type:

Record the plan type that you purchased from your provider. If you are unsure about this information, you may use Standard as the plan type.

WWAN Account Information User Name/Password:

Some WWAN service providers require user specific information, such as a login and password. If it does, you will need to provide such information during the setup process.

Note: WWAN Account Information is automatically populated based on the chosen service provider and plan type. In most cases, if you choose the correct service provider and plan type the WWAN account information does not have to be altered.

Page 10 Obtain WWAN Service Provider Information

Preparing Your WWAN PC Card

2

In this Section: This section provides instructions to set up your WWAN PC card for use in the SonicWALL TZ 190 Wireless appliance.

Alert: DO NOT insert your PC card into the SonicWALL TZ 190 Wireless appliance until you have completed the setup process for your card as described in this section.

Tip: If your WWAN PC card is already registered and activated with your service provider and you are able to access the Internet through your PC using this card, you may skip this section and continue to Registering Your SonicWALL , on page 29.

SonicWALL TZ 190 Wireless Getting Started Guide Page 11

Choose Your Service Provider This setup process differs depending on your service provider. Choose your service provider from the list below and follow the instructions on how to set up your WWAN PC card. If your service provider is not listed here, you must still complete the setup and activation for your PC card. Refer to the documentation that came with your PC card before using it with the SonicWALL TZ 190 Wireless appliance.

General WWAN PC Card Setup This section provides general instructions for setting up most WWAN PC cards: • WWAN PC card Setup , on page 13

Specific PC card Setup The following sections provide specific instructions for setting up these cards: • Sprint Wireless PC Card Setup , on page 16 • Cingular Wireless PC Card Setup , on page 20 • Verizon Wireless PC Card Setup , on page 25

Page 12 Choose Your Service Provider

WWAN PC card Setup Complete the following steps to set up and provision your WWAN PC card. Before continuing, verify that your WWAN PC card and service provider are supported by the SonicWALL TZ 190 Wireless appliance by visiting the SonicWALL TZ 190 Wireless product page at: Contact your PC card vendor for troubleshooting help with this section.

Alert: DO NOT insert your PC card into the computer until you have completed the setup process for your card as described in this section and successfully accessed the Internet through your PC using the PC card.

Installing PC card Software The following steps are general prerequisites necessary to set up most WWAN PC cards to work with the TZ 190 Wireless. 1. 2. 3. 4.

Install the software that came bundled with your WWAN PC card before activating the card. When prompted, insert the WWAN PC card into an available Type II PC card slot on the PC you are using for card configuration. Check for and install updates to your WWAN PC card, if available. Activate your PC card, if required.

SonicWALL TZ 190 Wireless Getting Started Guide Page 13

Verifying Your Connection After the card has been set up on your PC, you can view your connection type and verify that the WWAN PC card is transferring data.

Note: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled. 1. 2. 3. 4.

Use the software that came with your WWAN PC card to initialize a connection with your service provider. In the Windows interface, select Start > Run. Enter “cmd” in the Open field and click the OK button. At the prompt, type the command “ipconfig” and press Enter on the keyboard.

Page 14 WWAN PC card Setup

5.

Your network device status will display. Verify that you have obtained an IP Address for your Ethernet adaptor, and that all other Local Area Network Connections display “Media disconnected” as their status.

Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.

6.

Open a Web browser and navigate to a Web site, such as to verify that your connection can transfer data.

Congratulations! You have set up and provisioned your WWAN PC card. Continue with Connecting for Initial Setup , on page 31.

SonicWALL TZ 190 Wireless Getting Started Guide Page 15

Sprint Wireless PC Card Setup Complete the following steps to set up and provision your Sprint Wireless Mobile Broadband (WWAN) PC card. Contact your PC card vendor for troubleshooting help with this section.

Alert: DO NOT insert your PC card into the computer until you have completed the setup process for your card as described in this section and successfully accessed the Internet through your PC using the PC card.

Installing Sprint Software You must install the Sprint Wireless software that came bundled with your WWAN PC card before activating the card. 1. 2. 3. 4. 5.

Insert the Sprint CD that is provided with your WWAN PC card into the PC you intend to use for PC card setup. Follow the instructions on screen to complete the Sprint software installation. Restart your computer when prompted. After restarting your computer, open the Sprint PCS Connection Manager program, if the program does not automatically start. After launching, the program will check for updates. Click Update Now if needed. The download and update will proceed, if needed, and the program may restart.

Page 16 Sprint Wireless PC Card Setup

Setting Up the WWAN PC Card 1. 2.

3.

4. 5.

6.

7.

Insert your Sprint WWAN PC card. You may hear some audible indications of the card being discovered and installed. Once installed, you may be prompted to update the firmware on the WWAN PC card. Click OK to proceed with the update and click Next to agree to the license terms. The update will take a few minutes. The WWAN PC card will be rediscovered during this process. Click Finish when prompted. When the card is fully rediscovered, you will be prompted to call Sprint PCS Customer Service to activate the card. Do not click next until prompted to do so by the Sprint agent. The Sprint agent will provide you with an Activation Code to enter on the next screen. Enter the Activation Code and click Next. If the code is accepted, you will be prompted to enter your phone number (MDN) and MSID. Verify these numbers with the Sprint agent, and be sure to enter them correctly. Click Next when done. You will be prompted to confirm the correctness of the numbers. Entering incorrect information at this stage will require recovery by Sprint Technical Support. Click Yes once you have verified the numbers. You will be presented with a screen indicating the completion of the activation process. Click Finish to proceed.

SonicWALL TZ 190 Wireless Getting Started Guide Page 17

Verifying Your Connection It may take up to 4 hours for your WWAN PC card to become active on the Sprint network. After the card has been set up and is active, you can view your connection type and verify that the WWAN PC card is transferring data.

Alert: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled. 1. 2.

Open the Sprint PCS Connection Manager program. Click the GO button to connect to the Sprint network.

The WWAN PC card will take a few minutes to connect to the Sprint network. When the connection is ready, the status will read “Connected”.

Note: If you have recently activated your card with Sprint, keep in mind that the initial activation of your card may take up to 4 hours. Page 18 Sprint Wireless PC Card Setup

3. 4. 5. 6. 7.

In the Windows interface, select Start > Run. Enter “cmd” in the Open field and click the OK button. At the prompt, type the command “ipconfig” and press Enter on the keyboard. Your network device status will display. Verify that you have obtained an IP address for your Ethernet adaptor. Verify that all other Local Area Network Connections display “Media disconnected” as their status.

Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.

8.

Open a Web browser and navigate to a Web site, such as to verify that your connection can transfer data.

Congratulations! You have set up and provisioned your WWAN PC card. Continue with Connecting for Initial Setup , on page 31.

SonicWALL TZ 190 Wireless Getting Started Guide Page 19

Cingular Wireless PC Card Setup Complete the following steps to set up and provision your Cingular Wireless 3G PC card. Contact your PC card vendor for troubleshooting help with this section.

Alert: DO NOT insert your PC card into the computer until you have completed the setup process for your card as described in this section and successfully accessed the Internet through your PC using the PC card.

Installing Cingular Software You must install the Cingular software that came bundled with your 3G PC card before activating the card. 1. 2. 3. 4.

5.

Insert the Cingular CD that is provided with your PC card into the PC you intend to use for PC card setup. Follow the instructions on screen to complete the Cingular software installation. Restart your computer if prompted. If the Cingular Communications Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Cingular > Cingular Communications Manager to start the Communications Manager program. De-select all checkboxes on the first configuration page, including the Use this as my default Wi-Fi management utility option (checked by default).

Page 20 Cingular Wireless PC Card Setup

6. 7.

A warning screen will display. Check the Do not show this message again checkbox and click the OK button to continue. Click the Finish button to complete post-install configuration.

Preparing the PC Card Now that you have installed the required activation software on our PC, you can prepare the card for first use. 1. 2.

3.

Remove the PC card from the packaging and attach antenna if necessary. Locate and remove your SIM chip from its packaging if necessary. The SIM chip may be attached to a larger 3x5 plastic card from which it must be removed. Insert the SIM chip into your PC card. When inserted correctly, the SIM chip will “click” in place and sit perfectly flush with the edge of the PC card.

Note: Pay close attention to the orientation of your SIM card when inserting. Follow the manufacturer’s directions carefully when completing this procedure. WWAN PC Card

SIM chip

4.

Insert the PC card into an available Type II PC card slot on your Windows PC. SonicWALL TZ 190 Wireless Getting Started Guide Page 21

5.

If the Cingular Communications Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Cingular > Cingular Communications Manager to start the Communications Manager program. When the program is launched, you will see an interface similar to the one below.

GSM Tab - Use this tab for WWAN PC card management. Connect Button - Click here to make a connection to the current network.

3G - Indicator will show when you are connected to a 3G enabled network. Signal - Displays the signal strength of your current connection.

Status - Shows “ready” when a connection is available.

6.

Optionally, you may select Tools > Check for Updates to see if updates are available from your card vendor.

Note: Additional updates, including those for the PC card firmware may be recommended by Cingular. If so, follow the steps provided to complete these updates before continuing.

Page 22 Cingular Wireless PC Card Setup

Verifying Your Connection After the card has been set up on your PC, you can view your connection type and verify that the WWAN PC card is transferring data.

Alert: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled. 1.

If the Cingular Communications Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Cingular > Cingular Communications Manager to start the Communications Manager program.

The WWAN PC card will take a few minutes to connect to the Cingular network. When the connection is ready, the status will read “Ready: Cingular Accelerated”. 2. 3. 4. 5. 6. 7.

Click the Connect button to enable the network connection. In the Windows interface, select Start > Run. Enter “cmd” in the Open field and click the OK button. At the prompt, type the command “ipconfig” and press Enter on the keyboard. Your network device status will display. Verify that you have obtained an IP Address for your Ethernet adaptor. Verify that all other Local Area Network Connections display “Media disconnected” as their status. SonicWALL TZ 190 Wireless Getting Started Guide Page 23

Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.

8.

Open a Web browser and navigate to a Web site, such as to verify that your connection can transfer data.

Congratulations! You have set up and provisioned your WWAN PC card. Continue with Connecting for Initial Setup , on page 31.

Page 24 Cingular Wireless PC Card Setup

Verizon Wireless PC Card Setup Complete the following steps to set up and provision your Verizon Wireless WWAN PC card. Contact your PC card vendor for troubleshooting help with this section.

Alert: DO NOT insert your PC card into the computer until you have completed the setup process for your card as illustrated in this section and successfully accessed the Internet through your PC using the PC card.

Installing Verizon Software You must install the Verizon software that came bundled with your WWAN PC card before activating the card. 1. 2. 3. 4. 5. 6. 7. 8.

Insert the Verizon CD that is provided with your PC card into the PC you intend to use for PC card setup. Follow the instructions on screen to complete the software installation. Exit the installer after setup is complete. Navigate to Start > Programs > Verizon > VZAccess Manager to start the VZAccess Manager program. Click the Check for Updates button. When finished, click Next to continue. Select the Detect WWAN device only (1xEVDO/1xRTT/CDMA) radio button and click the Next button to continue. Click the Next button to search for your WWAN PC card. Select the PC card radio button and click the Next button to continue. SonicWALL TZ 190 Wireless Getting Started Guide Page 25

9. Click the Finish button to complete post-install configuration. 10. Insert the PC card into an available Type II PC card slot on your Windows PC. 11. When your card is found, click the Next button to continue. 12. Click the Activate button to activate your WWAN PC card.

Note: If activation fails on the first attempt, exit and then re-launch the program, keeping the WWAN PC card inserted during the process. 13. An “Activation Successful” message will display. Click the OK button. 14. Click the Next button. 15. Verify the correctness of the wireless phone number assigned to this PC card. If the number is incorrect, enter the correct number in the Phone number field. Click the Next button to continue. 16. Uncheck the Run VZAccess Manager at Startup option (unless you intend to use VZAccess to manage wireless connections on this PC). Click the Finish button.

Page 26 Verizon Wireless PC Card Setup

Verifying Your Connection After the card has been set up on your PC, you can view your connection type and verify that the WWAN PC card is transferring data.

Note: In order for the connection testing to be valid, it is important that you first disable all other network connections, such as a Wi-Fi or LAN connection, before continuing. Leave only your PC card connection enabled. 1.

If the VZAccess Manager program is running, skip to the next step. Otherwise, navigate to Start > Programs > Verizon > VZAccess Manager to start the VZAccess Manager program.

Connect/Disconnect Button - Click here to connect or disconnect from the current network.

Network Connection Shows “Verizon Wireless” when connected to the Verizon network.

Signal - Displays the signal strength of your current connection.

Status - Shows “connected” when connected to the Verizon network.

The WWAN PC card will take a few minutes to connect to the network. When the connection is ready, the signal indicator will light up green with bars to indicate connection strength. 2. Click the Connect button to enable the network connection. SonicWALL TZ 190 Wireless Getting Started Guide Page 27

3.

4. 5. 6. 7. 8.

If a disclaimer displays, click the Continue button. When the connection attempt is successful, the bottom-left corner of the VZAccess Manager will read Connected. In the Windows interface, select Start > Run. Enter “cmd” in the Open field and click the OK button. At the prompt, type the command “ipconfig” and press Enter on the keyboard. Your network device status will display. Verify that you have obtained an IP Address for your Ethernet adaptor. Verify that all other Local Area Network Connections display “Media disconnected” as their status.

Note: The name of your Ethernet adaptor may differ from the screenshot below. Common names for newly acquired cards are “Local Area Connection 2” or “Local Area Connection 3”.

9.

Open a Web browser and navigate to a Web site, such as to verify that your connection can transfer data.

Congratulations! You have set up and provisioned your WWAN PC card. Continue with Connecting for Initial Setup , on page 31. Page 28 Verizon Wireless PC Card Setup

Registering Your SonicWALL

3

In this Section: This section provides instructions for registering your SonicWALL TZ 190 Wireless. •

Registering with MySonicWALL.com , on page 30

Note: Product registration is an important part of the setup process, allowing you to enable product support, firmware updates and other key features.

SonicWALL TZ 190 Wireless Getting Started Guide Page 29

Registering with MySonicWALL.com 1. 2.

If you do not yet have a mysonicwall.com account, point your Web browser to to register before continuing. Locate and record your SonicWALL TZ 190 Wireless Serial Number and Authentication Code. This information is printed on the bottom panel of the appliance. This information was also recorded earlier, turn to Obtain Configuration Information , on page 8. My Serial Number My Authentication Code

3. 4.

In your Web browser, go to and login with your mysonicwall.com username and password. Enter your serial number in the Quick Register field and click the small gray arrow. Follow the on-screen instructions.

5. 6. 7.

Confirm your serial number. Enter a friendly name for this appliance. Enter your authentication code.

8. 9.

Click the Register button to continue. Follow the online prompts to complete the registration process.

Page 30 Registering with MySonicWALL.com

Connecting for Initial Setup

4

In this Section: This section provides initial configuration instructions for connecting your SonicWALL TZ 190 Wireless. • • • • •

Connect Antennas , on page 32 Insert the WWAN PC card , on page 32 Apply Power , on page 33 Connect the Computer to the LAN (1) Port , on page 34 Verify WAN / LAN / WLAN Connection , on page 35

SonicWALL TZ 190 Wireless Getting Started Guide Page 31

Connect Antennas 1. 2. 3.

Attach each of the (2) included antennas to an antenna port on the back of the SonicWALL TZ 190 Wireless. Screw the end of the antenna clockwise to tighten. Adjust the antennas to meet your space and signal requirements.

Console

WAN

OPT

8

7

6

5

4

3

2

1

Power

Insert the WWAN PC card Before inserting the WWAN PC card into your SonicWALL TZ 190 Wireless appliance, be sure your WWAN PC card is activated and unlocked. If you are not sure whether your card is unlocked or not, contact the PC card vendor to verify.

Alert: Do not insert or remove the WWAN PC card while the SonicWALL TZ 190 Wireless is powered on. 1.

Ensure the TZ 190 Wireless is not connected to a power source.

Page 32 Connect Antennas

2.

Insert your WWAN PC card “face up” into the PC CARD slot on the left side of the SonicWALL TZ 190 Wireless appliance. The card should sit firmly in place.

wwan signal link/act

wlan

wan opt on/act WiFiSec

link/act 10/100

TZ 190 wireless

Apply Power 1.

Connect the AC plug to the power supply.

2.

Plug one end of the power supply to the back of the SonicWALL TZ 190 Wireless. Connect the AC plug to an appropriate power outlet.

3.

3

2

1

Power

To AC power

The Power LED on the front panel lights up green and the Test LED lights up and blinks while the appliance performs a series of diagnostic tests. SonicWALL TZ 190 Wireless Getting Started Guide Page 33

When the Test LED is no longer lit, the SonicWALL TZ 190 Wireless is ready for configuration. If the Test LED stays lit for more than a few minutes, power cycle the appliance.

Connect the Computer to the LAN (1) Port Using the supplied network cable and the computer, connect the LAN (Ethernet) port on the computer to the LAN (1) port on the back of your SonicWALL TZ 190 Wireless. Console

WAN

OPT

8

7

6

5

4

3

2

1

SonicWALL TZ 190 Wireless

Power

LAN (1)

LAN (Ethernet)

Management Computer

Connect WAN Port to the Internet (Optional) If the SonicWALL TZ 190 Wireless will be using WAN as its primary Internet access, connect the appliance’s WAN port to your gateway device (usually your cable/DSL modem or T1 router) using a standard network cable.

Console

WAN

OPT

Internet

8

7

6

Router / Modem

5

4

3

2

1

Power

SonicWALL TZ 190 Wireless WAN

Router / Modem

Page 34 Connect the Computer to the LAN (1) Port

Verify WAN / LAN / WLAN Connection Once the cables are correctly connected, the WAN, LAN (1) and WLAN lights on the front panel of your SonicWALL TZ 190 Wireless illuminate, with the exception of the WAN if it is not in use. See the illustration below: Link/ACT (WAN / LAN 1) - A solid light indicates a network connection is present between the SonicWALL TZ 190 Wireless and another network appliance. A blinking light indicates connection activity. 10/100 (WAN / LAN 1) - A green light indicates a 10 Mbps port connection. An amber light indicates a 100 Mbps port connection. WLAN (on/act) - A solid light indicates the wireless transmitter is powered on. A blinking light indicates wireless activity.

Note: In order to connect to the SonicWALL TZ 190 Wireless, your computer must be set to accept dynamic “DHCP” addressing. For more information on configuring DHCP, turn to Appendix A: Configuring DHCP IP Addressing , on page 51.

SonicWALL TZ 190 Wireless Getting Started Guide Page 35

Page 36 Verify WAN / LAN / WLAN Connection

Running the Setup Wizard

5

In this Section: This section provides instructions to log in and configure your SonicWALL TZ 190 Wireless using the SonicWALL Setup Wizard. • • •

Accessing the SonicOS Web Management Interface , on page 38 Verify Management Interface Connectivity , on page 41 Verify WAN (Internet) Connectivity , on page 42

Tip: Before completing this section, fill out the information in Obtain Configuration Information , on page 8 and Obtain Internet Service Provider (ISP) Information , on page 9. You will need to enter this information during the Setup Wizard.

SonicWALL TZ 190 Wireless Getting Started Guide Page 37

Accessing the SonicOS Web Management Interface Your SonicWALL TZ 190 Wireless employs the use of a Web-based management interface for setup and configuration. Complete the following steps to log into the management interface. 1.

In a Web browser on the computer, navigate to (the default IP address of the SonicWALL TZ 190 Wireless).

The Setup Wizard will load. If the Setup Wizard does not display upon initial loading of the SonicWALL TZ 190 Wireless management interface, refer to page 40 for additional troubleshooting information. 2. Make a language selection and click the Next button to continue.

Page 38 Accessing the SonicOS Web Management Interface

3.

4.

Follow the on-screen prompts to complete the Setup Wizard. Refer to the information you recorded in Obtain Configuration Information , on page 8, Obtain Internet Service Provider (ISP) Information , on page 9, and Obtain WWAN Service Provider Information , on page 10 to complete this section. Depending on the changes made during your setup configuration, the SonicWALL may restart.

Note: Although the Setup Wizard guides you through basic wireless connectivity setup, to enable advanced security options such as WPA2 encryption, you must also run the Wireless Wizard. For more information on securing your wireless network, refer to the latest SonicOS Enhanced Administrator's Guide, available at .

SonicWALL TZ 190 Wireless Getting Started Guide Page 39

Unable to See the Setup Wizard? •



If you see the login screen, but not the Setup Wizard: • Configure your Web browser to allow pop-ups for the SonicWALL TZ 190 Wireless. • Log into the security appliance using “admin” as the user name and “password” as the password. After you log in, click the Wizards button on the System > Status page. If you do not see the login screen or the Setup Wizard: • Did you correctly enter the SonicWALL TZ 190 Wireless management IP address, 192.168.168.168, in your Web browser? • Is your computer set to accept DHCP addressing or set to a static IP address within the 192.168.168.x subnet range? If not, see Appendix A: Configuring DHCP IP Addressing , on page 51 for instructions on changing your Local Area Connection settings. • Do you have the Ethernet cable connected between your computer and the LAN (1) port on your SonicWALL TZ 190 Wireless? • Do you need to add the SonicWALL TZ 190 Wireless to your list of trusted sites? Use the default IP address (192.168.168.168) for this purpose. •

Is the Test LED on the front panel of your SonicWALL TZ 190 Wireless lit? If the Test LED stays lit for more than a few minutes after the initial power on sequence, power cycle the SonicWALL TZ 190 Wireless.

Page 40 Unable to See the Setup Wizard?

Verify Management Interface Connectivity 1.

If your SonicWALL did not require a restart, skip to the Verify WAN (Internet) Connectivity section, on page 42. Otherwise, continue with step 2.

2.

Wait for the SonicWALL TZ 190 Wireless to reboot. When the Test LED is no longer lit, the SonicWALL TZ 190 Wireless is ready for login. If the login page does not display after reboot, open a Web browser on the computer and manually navigate to the LAN IP address of your SonicWALL TZ 190 Wireless. Using your new username and password, log into the appliance.

3.

4.

The System > Security Dashboard page (shown below) displays. You have correctly configured the SonicWALL TZ 190 Wireless to work with the computer on your LAN. Complete the next section to verify WAN (Internet) connectivity.

SonicWALL TZ 190 Wireless Getting Started Guide Page 41

Verify WAN (Internet) Connectivity Complete the following steps to confirm your Internet connectivity. 1. 2. 3.

In the Windows interface, select Start > Run. Enter “cmd” in the Open field and click the OK button. At the prompt, type the command “ping www.sonicwall.com” and press Enter on the keyboard.

If the ping times out, you may have to renew your computer’s IP address. Turn to Appendix B: Troubleshooting Internet Connectivity , on page 52 for additional information. 4. If the ping is successful, use a computer connected to the LAN (1) port to launch a new Web browser. 5. Navigate to an Web site such as . If the Web site displays, your SonicWALL TZ 190 Wireless is configured correctly as your gateway device. SonicWALL WWAN

wwan signal link/act

wlan

wan opt WiFiSec on/act

link/act 10/100

TZ 190 wireless

LAN (1) Internet

WAN

Management Station

Page 42 Verify WAN (Internet) Connectivity

Verifying Your WWAN Connection

6 7

In this Section: This section provides instructions to ensure proper connectivity of your SonicWALL TZ 190 Wireless appliance. • •

Managing the WWAN Connection Status , on page 44 Check WWAN Internet Connectivity , on page 46

SonicWALL TZ 190 Wireless Getting Started Guide Page 43

Managing the WWAN Connection Status The Network > Interfaces page allows you to view the current WWAN connection status. 1. 2. 3.

Log into the SonicWALL TZ 190 Wireless appliance management interface. Navigate to Network > Interfaces. In the Interface Settings section, the WWAN interface line displays the current status as follows:

On hook

Indicates that the WWAN card is present but not yet connected.

Connected and starting PPP authentication

Indicates that the WWAN card is associated and currently attempting a connection to the WWAN network.

Connected

Indicates an active connection.

Page 44 Managing the WWAN Connection Status

The Connection Manager window allows you to connect, disconnect and view current WWAN connection status. 1. 2.

In the SonicWALL TZ 190 Wireless appliance management interface, navigate to Network > Interfaces. In the Interface Settings section, under WWAN, click the Manage button.

3.

The Connection Manager windows displays your connection status.

4.

If the Connection Manager shows “disconnected”, click the Connect button. You will connect to a network if one is available.

SonicWALL TZ 190 Wireless Getting Started Guide Page 45

Check WWAN Internet Connectivity Complete the following steps to confirm your WWAN Internet connectivity. 1. 2.

3.

Unplug your appliance’s WAN port, (if you plugged it in during the initial setup). Wait a few moments for the TZ 190 to failover to the WWAN for Internet connectivity. Refer to the front panel of the appliance to see when the WWAN PC card shows activity. Launch a Web site, such as in a browser, using a computer that is connected to the SonicWALL TZ 190 Wireless appliance and using the SonicWALL as its sole Internet connection.

If the Web site displays, your SonicWALL TZ 190 Wireless is operational and connected to a valid WWAN service provider account. If the Web site does not display, refer to Appendix B: Troubleshooting Internet Connectivity , on page 52.

Note: Remember to plug the WAN back in if you wish to use WWAN as a failover.

Page 46 Check WWAN Internet Connectivity

Connecting to Your Network

7

In this Section: This section provides SonicWALL TZ 190 Wireless basic network connectivity verification procedures and examples. • • •

Connect and Configure Your Network , on page 48 The Front Panel , on page 49 The Back Panel , on page 50

SonicWALL TZ 190 Wireless Getting Started Guide Page 47

Connect and Configure Your Network

wlan

TZ 190 wireless

WWAN

Internet

Local Wired Clients

Your SonicWALL TZ 190 Wireless is equipped with a DHCP server. If you enabled this feature in the Setup Wizard, your DHCP-enabled network clients are automatically provisioned by the SonicWALL appliance. To set up: 1. 2. 3.

Set your clients to obtain their IP address automatically. Connect your wired clients (directly or using a hub/switch) to the LAN ports (1-8) on your SonicWALL TZ 190 Wireless. Connect wireless clients to your new wireless SSID (the default SSID is sonicwall). This step may require additional configuration if you enabled WEP or WPA encryption. For detailed wireless setup instructions, refer to the Wireless chapter in the SonicOS Enhanced Administrator’s Guide.

Congratulations! You have successfully completed the setup of your SonicWALL TZ 190 Wireless appliance.

Page 48 Connect and Configure Your Network

The Front Panel

wwan signal link/act

wlan

wan opt WiFiSec on/act

link/act 10/100

TZ 190 wireless

Feature Description Power LED Indicates the SonicWALL TZ 190 Wireless is powered on. Test LED Solid: Indicates that the SonicWALL TZ 190 Wireless is in test mode. Blinking: The unit is booting up, or restarting. This can also indicate that the unit is in safe mode. WWAN (signal): Indicates that the WWAN card is connected to the service provider. (link/act): Indicates that the WWAN card is active. WLAN (WiFiSec): Indicates WiFiSec wireless security is operational. (on/act): Solid indicates the wireless radio is powered on, blinking indicates wireless activity. OPT The OPT Port is not configurable on this appliance. WAN Indicates a device link, activity and connection speed on your WAN port. LAN (1-8) Indicates a device link, activity and connection speed on individual LAN ports (numbered 1-8). Link/ACT Solid: Indicates a device is connected to the specified port(s). Blinking: Indicates activity on the specified port(s). 10/100 Green: Indicates 10M connection on the specified port(s). Amber: Indicates 100M connection on the specified port(s). SonicWALL TZ 190 Wireless Getting Started Guide Page 49

The Back Panel

Console

Feature Antenna Connections Console Port

WAN Port

OPT Port LAN Ports (1-8)

Reset Button Power

Page 50 The Back Panel

WAN

OPT

8

7

6

5

4

3

2

1

Power

Description Provide (2) connection points for the included wireless antennas. Provides a console connection to the SonicWALL appliance. This feature is not supported on the SonicWALL TZ 190 Wireless. Provides a connection between your SonicWALL TZ 190 Wireless and the Internet, usually connecting through a modem or router. The OPT Port is not configurable on this appliance. Provides 8 fully-configurable ports for connection between your SonicWALL TZ 190 Wireless and the devices on your network. These ports can be connected directly to a computer, or to a network switch or hub. Provides the capability to reboot your SonicWALL TZ 190 Wireless to a special diagnostic “safe-mode”. Provides a power connection using the supplied AC adaptor.

Appendix A: Configuring DHCP IP Addressing Complete the following section based on your operating system in order to configure your management computer to obtain an IP address automatically (using DHCP addressing): Windows Vista 1. 2. 3. 4. 5. 6.

From the Start menu, right-click Network and select Properties. In the Tasks menu, click Manage network connections, the Network Connections windows displays. Right-click on your Local Area Connection and select Properties. In the list, double-click Internet Protocol Version 4 (TCP/IP). Select Obtain an IP address automatically and Obtain a DNS address automatically. Click OK, and then click OK again for the settings to take effect.

Windows XP 1. 2. 3. 4. 5.

From the Start menu, highlight Connect To and then select Show All Connections. Right-click on your Local Area Connection and select Properties. In the list, double-click Internet Protocol (TCP/IP). Select Obtain an IP address automatically and Obtain a DNS address automatically. Click OK, and then click OK again for the settings to take effect.

Windows 2000 1. 2. 3. 4. 5. 6.

From your Windows Start menu, select Settings. Open Network and Dial-up Connections. Click Properties. Highlight Internet Protocol (TCP/IP) and click Properties. Select Obtain an IP address automatically and Obtain a DNS address automatically. Click OK for the settings to take effect.

SonicWALL TZ 190 Wireless Getting Started Guide Page 51

Appendix B: Troubleshooting Internet Connectivity Refer to this section for help in connecting to the Internet. • • • • • •

Did you open a new browser window to launch the Web site? Try closing out all browser windows and launching the browser again. Is your computer set to accept DHCP addressing or, if using static IP addressing, is your IP address set to a range within the SonicWALL’s LAN subnet? Has your IP address renewed from the setting changes? Manually refresh them or reboot your computer. Refer to the Renewing your IP address section for additional information. Is your SonicWALL WAN port connected to your Internet source and showing (link/act, 10/100) activity? Verify that the network settings you recorded on page 8 of this guide are correct. Did you enter your network information from page 8 of this guide correctly in the Setup Wizard?

Renewing your IP Address 1. 2. 3. 4.

In the Windows interface, select Start > Run. Enter “cmd” in the Open field and click the OK button. At the prompt, type the command “ipconfig /release” and press Enter on the keyboard. At the prompt, type the command “ipconfig /renew” and press Enter on the keyboard.

For further help troubleshooting Internet connectivity, please refer to the SonicOS Enhanced Administrator’s Guide.

Page 52 Appendix B: Troubleshooting Internet Connectivity

Appendix C: Safety Instructions and Regulatory Information Regulatory Model/Type

Product Name

APL18-046

TZ 190 Wireless

Mounting the SonicWALL •





• •



Lithium Battery Warning

Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended. Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers The included power cord is intended for use in North America only. For European Union (EU) customers, a power cord is not included. Ensure that no water or excessive moisture can enter the unit. Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended. Consideration must be given to the connection of the equipment to the supply circuit and the effect of overloading the circuits has minimal impact on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern.

The Lithium Battery used in the SonicWALL security appliance may not be replaced by the user. Return the SonicWALL security appliance to a SonicWALL-authorized service center for replacement with the same or equivalent type recommended by the manufacturer. If, for any reason, the battery or SonicWALL security appliance must be disposed of, do so following the battery manufacturer's instructions.

Cable Connections All Ethernet and RS232 (Console) cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWALL is located.

Power Supply Information If the power supply is missing from your SonicWALL product package, please contact SonicWALL Technical Support at 408-752-7819 for a replacement. This product should only be used with a UL listed power supply marked “Class 2” or “LPS”, with an output rated 12 VDC, minimum 1.66 A.

SonicWALL TZ 190 Wireless Getting Started Guide Page 53

Weitere Hinweise zur Montage •





• •



Wählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht ausgesetzt ist und sich nicht in der Nähe von Wärmequellen befindet. Die Umgebungstemperatur darf nicht mehr als 40 °C betragen. Führen Sie die Kabel nicht entlang von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern oder Breitbandverstärkern. Das eingeschlossene Netzkabel ist für Gebrauch in Nordamerikas nur vorgehabt. Für Europaïsche Union (EU) Kunden, ist ein Netzkabel nicht eingeschlossen. Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit geschützt ist. Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die Lüftungsschlitze an der Seite des Gehäuses frei sind. Hier ist ein Belüftungsabstand von mindestens 26 mm einzuhalten. Vergewissern Sie sich, dass das Gerät sicher im Rack befestigt ist. Insbesondere muss auf nicht direkte Anschlüsse an Stromquellen geachtet werden wie z. B. bei Verwendung von Mehrfachsteckdosen.

Hinweis zur Lithiumbatterie Die in der Internet Security appliance von SonicWALL verwendete Lithiumbatterie darf nicht vom Benutzer ausgetauscht werden. Zum Austauschen der Batterie muss die SonicWALL in ein von SonicWALL autorisiertes ServiceCenter gebracht werden. Dort wird die Batterie durch denselben oder entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt. Beachten Sie bei einer Entsorgung der Batterie oder der SonicWALL Internet Security appliance die diesbezüglichen Anweisungen des Herstellers.

Kabelverbindungen Alle Ethernet- und RS232-C-Kabel eignen sich für die Verbindung von Geräten in Innenräumen. Schließen Sie an die Anschlüsse der SonicWALL keine Kabel an, die aus dem Gebäude herausgeführt werden, in dem sich das Gerät befindet.

Informationen zur Stromversorgung Sollte das Netzteil nicht im Lieferumfang der SonicWALL enthalten sein, wenden Sie sich diesbezüglich an den technischen Support von SonicWALL (Tel.: +1-408-752-7819). Dieses Produkt darf nur in Verbindung mit einem nach den Normen der Underwriter Laboratories, USA als „UL-gelistet“ zugelassenen Netzteil der Kategorie „Class 2“ oder „LPS“ verwendet werden. Ausgang: 12 VDC Gleichsspannung, mind. 1,66 A.

Page 54 Appendix C: Safety Instructions and Regulatory Information

FCC Part 15 Class B Notice NOTE: This equipment was tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. And, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference using one or more of the following measures: • • • •

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from the receiver connection. Consult SonicWALL for assistance.

Complies with EN55022 Class B and CISPR22 Class B. *Refer to the label on the bottom of the unit for device information including Class A or Class B FCC information.

North American Authorized Channels SonicWALL declares that the APL17-049 (FCC ID: QWU-049) (IC: 4408A-049) when sold in US or Canada is limited to CH1~CH11 by specified firmware controlled in the USA.

FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.9 inches) between the radiator (antenna) and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For more information regarding the above statement, please contact SonicWALL, Inc. at: 1143 Borregas Avenue, Sunnyvale, CA 94089-1306, 1-408-745-9600.

Canadian Radio Frequency Emissions Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à toutes la norme NMB-003 du Canada.

SonicWALL TZ 190 Wireless Getting Started Guide Page 55

:/$15/$1 *+] Indoor Onl\ D'intérieur Seulement Dell'interno Soltanto De interior Solamente

Binnen slechts Innen Nur Indoor Somen te

7KLVHTXLSPHQWPD\EHRSHUDWHGLQ %HWULHEGLHVHU$XVUVWXQJZLUGLQQHQHUODXEW / RSpUDWLRQGHFHWpTXLSHPHQWHVWSHUPLVHGDQV AT (( I( NO &H

B( )I IT PL GB

&< )R LT PT

&Z D( LU SK

DK HU NL (S

&RXQWU\DQGFKDQQHOVHOHFWLRQLVPDGHLQVRIWZDUH)ROORZXVHU GRFXPHQWDWLRQWRPDNHFRXQWU\DQGFKDQQHOVHWWLQJ /DQGXQG.DQDODXVZDKOVLQGLQ6RIWZDUHJHPDFKW)ROJHQ6LH Verbraucherdokumentation, um Land und Kanal zu machen, VHW]HQG /DVpOHFWLRQGHSD\VHWFDQDOHVWIDLWHGDQVOHORJLFLHO6XLYH]OD GRFXPHQWDWLRQG XWLOLVDWHXUSRXUIDLUHOHSD\VHWODFDQDO VpOHFWLRQ

6RQLFZDOOWtPWRSURKODãXMHåHWHQWRAPL18-046MHYHVKRGČVH ]iNODGQtPLSRåDGDYN\GDOãtPLS‡tVOXãQêPLXVWDQRYHQtPL VPČUQLFH(6 Undertegnede Sonicwall erklærer herved, at følgende XGVW\U APL18-046 overholder de væsentlige krav og øvrige relevante NUDYLGLUHNWLY() Hiermit erklärt Sonicwall, dass sich das Gerät APL18-046 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie (*EHILQGHW +HUHE\6RQLFZDOOGHFODUHVWKDWWKLV$3/LVLQ compliance with the essential requirements and other relevant SURYLVLRQVRI'LUHFWLYH(& Por medio de la presente Sonicwall declara que el APL18-046 FXPSOHFRQORVUHTXLVLWRVHVHQFLDOHV\FXDOHVTXLHUDRWUDV GLVSRVLFLRQHVDSOLFDEOHVRH[LJLEOHVGHOD'LUHFWLYD&( Par la présente Sonicwall déclare que l'appareil APL18-046 est conforme aux exigences essentielles et aux autres dispositions SHUWLQHQWHVGHODGLUHFWLYH&( &RQODSUHVHQWH6RQLFZDOOGLFKLDUDFKHTXHVWR$3/ è conforme ai requisiti essenziali ed alle altre disposizioni SHUWLQHQWLVWDELOLWHGDOODGLUHWWLYD&( Šiuo Sonicwall deklaruoja, kad šis APL18-046 atitinka esminius UHLNDODYLPXVLUNLWDV(%'LUHNW\YRVQXRVWDWDV Hierbij verklaart Sonicwall dat het toestel APL18-046 in overeenstemming is met de essentiële eisen en de andere UHOHYDQWHEHSDOLQJHQYDQULFKWOLMQ(* Sonicwall declara que este APL18-046 está conforme com os requisitos essenciais e outras disposições da Directiva &( 6RQLFZDOOWêPWRY\KODVXMHåH$3/VS‡‡D]iNODGQp SRåLDGDYN\DYãHWN\SUtVOXãQpXVWDQRYHQLD6PHUQLFH (6 6RQLFZDOOYDNXXWWDDWlWHQHWWl$3/W\\SSLQHQODLWHon GLUHNWLLYLQ(