FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
D10 Series SENSORS
Redefining High-Performance Fiber Optic Sensing • Features advanced fiber optic amplifier for use with plastic fibers • Available in bipolar, discrete and analog/discrete output models • Available with a numeric or bargraph display on Expert™ models • Delivers high-performance, low-contrast sensing with automatic TEACH options or manual adjustment • Available with visible red or green beam • Provides light-operate or dark-operate operation • Includes specially designed models for reliable detection of objects as small as 1.5 mm • Features bussable models for side-by-side mounting and simplified wiring of up to 16 sensors • Features thin 10 mm housing for standard 35 mm DIN-rail mounting
D10 Expert ™ with Numeric Display page 223 • Numeric display of signal strength and operating status • Two output options: two discrete outputs in the same sensor; or discrete output and either a 4-20 mA current or a 0-10V dc voltage analog output in the same sensor • Push buttons for easy-to-set static, dynamic light set, dark set and window set programming • Manual fine tuning and remote configuration using TEACH wire • Four mode power and speed selection with automatic crosstalk avoidance circuity • Response times as fast as 50 microseconds
D10 Expert ™ with Bargraph Display page 224 • Easy-to-read 8-segment light bar display indicator for TEACH and signal strength • Bipolar discrete outputs: one current sourcing (PNP) and one current sinking (NPN) • Push buttons for easy-to-set static, dynamic light set, dark set and window SET programming • Manual fine tuning • Bussable power models with improved temperature compensation for side-byside mounting and simplified wiring of up to 16 sensors • Selectable high-speed mode option for 200 microsecond response
D10—Discrete Output page 224 • 12-turn manual sensitivity adjustment • Pulse rate LED indicator for signal strength • Bipolar discrete outputs: one current sourcing (PNP) and one current sinking (NPN) • Response time as fast as 200 microseconds
D10 Expert ™ Small Object Counter page 225 • Reliable low-contrast sensing for small object counting • Easy-to-set selectable threshold with automatic compensation algorithm to compensate for dust or contamination on the fiber optic array and for ambient temperature changes • Single discrete output plus Health mode output to indicate preventative maintenance is required • A choice of three standard size fiber optic assemblies • Custom size fibers for your application • User-configurable Dynamic Event Stretcher (DES) to prevent double counting of objects • Push buttons or remote wire for easy sensor configuration
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
10.0 mm -
LAY DE 0 msms 40
+
Measurement & Inspection Sensors 35.9 mm
Vision
68.1 mm
Wireless
10.0 mm
Indicators
D10—Discrete Models
Safety Light Screens Safety Laser Scanners
35.9 mm
Fiber Optic Safety Systems
68.1 mm
Safety Controllers & Modules
D10 Expert™ Models with Bargraph Display
Safety Two-Hand Control Modules Safety Interlock Switches
68.1 mm
Emergency Stop Devices
35.9 mm
ACCESSORIES
D10 Expert™ Models with Numeric Display
page 229
10.0 mm
D10 Expert™ with Numeric Display—Dual Discrete, 12-24V dc Sensing Mode/LED
Range
PLASTIC FIBER
Range varies by Power Level/Speed Selection used and with fiber optics used. See data sheet for range information.
Visible Red LED
Connection
Models Dual NPN
Models Dual PNP
2m
D10DNFP
D10DPFP
6-pin Snap-on Pico QD
D10DNFPQ
D10DPFPQ
2m
D10DNFPG
D10DPFPG
D10DNFPGQ
D10DPFPGQ
6-pin Snap-on Pico QD
PLASTIC PLASTIC FIBER FIBER
D10 Expert™ with Numeric Display—Analog/Discrete, 12-24V dc Sensing Mode/LED
Range
Visible Red LED
Connection
Analog Output
2m PLASTIC FIBER
Range varies by Power Level/Speed Selection used and with fiber optics used. See data sheet for range information.
PLASTIC PLASTIC FIBER FIBER
Visible Green LED
6-pin Snap-on Pico QD
Models PNP
D10INFP
D10IPFP
D10INFPQ
D10IPFPQ
D10INFPG
D10IPFPG
D10INFPGQ
D10IPFPGQ
4-20 mA
2m 6-pin Snap-on Pico QD
Models NPN
Visible Green LED
4-20 mA
Connection options: A model with a QD requires a mating cordset (see page 229). For 9 m cable, add suffix W/30 to the 2 m model number (example, D10DNFP W/30).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS D10 D12 R55F PLASTIC FIBERS GLASS FIBERS
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
D10 Expert™ with Numeric Display—Analog/Discrete, 15-24V dc
SENSORS
Sensing Mode/LED
Range
Visible Red LED
Analog Output
Connection
Models NPN
2m PLASTIC FIBER
2m
D10 Expert™ with Bargraph Display—Discrete Sensing Mode/LED
Range
Connection
Range varies by Power Level/ Speed Selection used and with fiber optics used. See fibers section on page 239 or reference data sheet for range information.
PLASTIC PLASTIC FIBER FIBER
6-pin Snap-on Pico QD 2m
D10UPFP
D10UNFPQ
D10UPFPQ
D10UNFPG
D10UPFPG
D10UNFPGQ
D10UPFPGQ
Visible Red LED
Output Type
Supply Voltage
Description
Models
2m PLASTIC FIBER
D10UNFP
0-10V
6-pin Snap-on Pico QD
PLASTIC PLASTIC FIBER FIBER
D10BFP Bipolar NPN/PNP
D10BFPQ 10 to 30V dc
Standard models D10BFPG
6-pin Snap-on Pico QD
Models PNP
0-10V
6-pin Snap-on Pico QD
Range varies by Power Level/Speed Selection used and with fiber optics used. See fibers section on page 239 or reference data sheet for range information.
Visible Green LED
D10BFPGQ
Visible Green LED
Excess Gain
Beam Pattern
EGC-1 to EGC-4 (p. 229)
BP-1 to BP-4 (p. 230)
EGC-5 to EGC-8 (p. 229)
BP-5 to BP-8 (p. 230)
EGC-1 to EGC-4 (p. 229)
BP-1 to BP-4 (p. 230)
Bussable Power Models
PLASTIC FIBER
Range varies by Power Level/ Speed Selection used and with fiber optics used. See fibers section on page 239 or reference data sheet for range information.
Bipolar NPN/PNP 2m
PNP
12 to 30V dc
NPN
Main unit
D10B5FP
Sub unit
D10B2PFP
Sub unit
D10B2NFP
D10—Discrete, 10-30V dc Sensing Mode/LED
Visible Red LED
Range
Connection 2m
PLASTIC FIBER
Range varies by Power Level/Speed Selection used and with fiber optics used. See fibers section on page 239 or reference data sheet for range information.
PLASTIC PLASTIC FIBER FIBER
4-pin Snap-on Pico QD 2m 4-pin Snap-on Pico QD
Output Type
Response Time
Bipolar NPN/PNP
500 microseconds
Bipolar NPN/PNP
500 microseconds
Connection options: A model with a QD requires a mating cordset (see page 229). For 9 m cable, add suffix W/30 to the 2 m model number (example, D10UNFP W/30).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Visible Green LED
Models D10AFP D10AFPQ D10AFPG D10AFPGQ
More on next page
D10—Discrete, 10-30V dc (cont’d) Sensing Mode/LED
Visible Red LED
Range
Connection
HIGH-SPEED
2m 4-pin Snap-on Pico QD
Range varies by Power Level/Speed Selection used and with fiber optics used. See fibers section on page 239 or reference data sheet range information.
PLASTIC FIBER HIGH-SPEED
2m 4-pin Snap-on Pico QD
PLASTIC PLASTIC FIBER FIBER
Visible Green LED
Output Type
Response Time
Bipolar NPN/PNP
200 microseconds
Bipolar NPN/PNP
200 microseconds
Models D10AFPY D10AFPYQ D10AFPGY D10AFPGYQ
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
D10 Expert™ Small Object Counter with Numeric Display—Discrete, 12-24V dc Sensing Mode/LED
Connection
Output
2m
NPN
6-pin Snap-on Pico QD PLASTIC FIBER
2m
PNP
6-pin Snap-on Pico QD
Visible Red LED
Sensor Models D10DNCFP D10DNCFPQ
D10
D10DPCFPQ
R55F
10 x 25 mm 25 x 25 mm 34 x 25 mm
Fiber Exit
GLASS FIBERS
Minimum Object Detection†
Side Exit End Exit Side Exit End Exit Side Exit End Exit
D12 PLASTIC FIBERS
Fiber Optic Arrays Detection Window Dimensions**
FIBER SENSORS
D10DPCFP
1.5 mm 3 mm 4 mm
Array Models* PFCVA-10X25-S PFCVA-10X25-E PFCVA-25X25-S PFCVA-25X25-E PFCVA-34X25-S PFCVA-34X25-E
Connection options: A model with a QD requires a mating cordset (see page 229). For 9 m cable, add suffix W/30 to the 2 m model number (example, D10DNDFP W/30). * Custom fiber arrays and mounting configurations are possible. Consult factory for assistance with your small object counting application. ** Detailed dimension drawings for fibers are on page 254. † With 2% Threshold Offset Percentage
D10 Expert™ with Numeric Display—Dual-Discrete Specifications Required Fiber Optic Cable
Banner P-Series plastic fibers (See Plastic Fiber Optic section, page 239)
Supply Voltage and Current
12 to 24V dc (10% max. ripple) at less than 65 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltage.
Output Configuration
Two independently configured current sourcing (PNP) or current sinking (NPN) solid-state transistors, depending on model.
Output Rating
150 mA max. load OFF-state leakage current: less than 10 µA at 24V dc ON-state saturation voltage: NPN: less than 1.5V at 150 mA load
Output Protection Circuitry
Protected against false pulse on power-up and continuous short-circuit
PNP: less than 2.5V at 150 mA load
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
SENSORS
D10 Expert™ with Numeric Display—Dual-Discrete Specifications
(cont’d)
Output Response Time
Programmable, 50 microseconds, 200 microseconds, 1 millisecond, 2.5 milliseconds
Delay at Power-up
Less than 1 second; outputs do not conduct during this time.
Adjustments
Two push buttons or remote programming of (TEACH) switching threshold response time, OFF-delay, light/dark operate, and display
Indicators
Four-digit digital display plus LED indicators for active channel, push-button lockout, OFF-delay and light/dark operate selection; two yellow LED output indicators.
Construction
Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear polycarbonate cover.
Environmental Rating
IEC IP50; NEMA 1
Connections
PVC-jacketed 2 m or 9 m 6-wire integral cable, or integral 6-pin Pico-style quick-disconnect fitting. QD cordsets are ordered separately. See page 229.
Operating Conditions
Temperature: -20° to +55° C
Installation
Storage Temperature: -20° to +80° C
Relative humidity: 90% @ 50° C
Number of Devices Stacked
Ambient Temperature Rating
Load Specification
3
55° C
150 mA
7
50° C
50 mA
10
45° C
50 mA
35 mm DIN rail or included mounting bracket
Certifications Hookup Diagrams
DC15 (p. 719)
D10 Expert™ with Numeric Display—Analog/Discrete Specifications Required Fiber Optic Cable
Banner P-Series plastic fibers (See Plastic Fiber Optic section, page 239)
Supply Voltage and Current
4-20 mA Analog Models: 12-24V dc (10% max. ripple) at less than 65 mA exclusive of load 0-10V dc Analog Models: 15-24V dc (10% max. ripple) at less than 70 mA exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltage.
Output Configuration
Two independently configurable outputs, depending on model: NPN w/analog (4-20 mA or 0-10V) or PNP w/analog (4-20 mA or 0-10V)
Output Rating
Discrete Output: 150 mA, max. load OFF-state leakage current: less than 10 µA at 24V dc ON-state saturation voltage: NPN: < 1.5V @ 150 mA PNP: < 2.5V @ 150 mA
Output Protection Circuitry
Protected against false pulse on power-up and continuous short-circuit
Output Response Time
Discrete Output: Programmable, 50 microseconds, 200 microseconds, 1 millisecond, 2.5 milliseconds Analog Output: 1 millisecond
Delay at Power-up
Less than 1 second; outputs do not conduct during this time.
Adjustments
Push-button or remote programming of (TEACH) switching threshold response time, OFF-delay, light/dark operate, and display
Indicators
Four-digit digital display plus LED indicators for active channel, push-button lockout, OFF-delay and light/dark operate selection; two yellow output indicators.
Construction
Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear polycarbonate cover.
Environmental Rating
IEC IP50; NEMA 1
Connections
PVC-jacketed 2 m or 9 m 6-wire integral cable, or integral 6-pin Pico-style quick-disconnect. QD cordsets are ordered separately. See page 229. Temperature: -20° to +55° C
Operating Conditions
Installation
Analog Output: 4-20 mA or 0-10V dc Load: 4-20 mA Models: 100Ω max. impedance 0-10V dc Models: 1 MΩ min. impedance
Storage Temperature: -20° to +80° C
Relative humidity: 90% @ 50° C
Number of Devices Stacked
Ambient Temperature Rating
Load Specification
3
55° C
150 mA
7
50° C
50 mA
10
45° C
50 mA
35 mm DIN rail or included mounting bracket
Certifications Hookup Diagrams
NPN Models: DC16 (p. 719)
PNP Models: DC17 (p. 720)
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
D10 Expert™ with Bargraph Display—Discrete Specifications Standard Sensors Required Fiber Optic Cable Supply Voltage and Current
Models with Bussable Power
Banner P-Series plastic fibers (See Plastic Fiber Optic section, page 239) 10 to 30V dc (10% max. ripple) at less than 45 mA, exclusive of load
12 to 30V dc (10% max. ripple) at less than 45 mA, exclusive of load
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision
Supply Protection Circuitry
Protected against reverse polarity, over voltage and transient voltage.
Wireless
Delay at Power Up
200 milliseconds max.; outputs do not conduct during this time
Indicators
850 milliseconds max.; outputs do not conduct during this time Main units: Bipolar; 1 current sourcing (PNP) and 1 current sinking (NPN) Sub-units: 1 current sourcing (PNP) or 1 current sinking (NPN) output, depending on model 100 mA max. load (derate 1 mA per ° C) OFF-state leakage current: less than 5 µA at 30V dc ON-state saturation voltage: NPN: less than 1.5V PNP: less than 2V Less than 15V supply (9 m cable): up to 4 units with 100 mA outputs up to 8 units with 50 mA outputs
Output Configuration Bipolar: 1 current sourcing (PNP) and 1 current sinking (NPN) Output Rating
150 mA max. load @ 25° C (derate 1 mA per ° C increase) OFF-state leakage current: less than 5 µA at 30V dc ON-state saturation voltage: NPN: less than 200 mV at 10 mA and 1V at 150 mA load PNP: less than 1V at 10 mA and 1.5V at 150 mA load
Output Protection Circuitry
Protected against output short-circuit, continuous overload, transient over-voltages, and false pulse on power-up
Output Response Time
500 microseconds (normal mode) or 200 microseconds (high-speed mode)
Repeatability
100 microseconds (normal mode) or 66 microseconds (high-speed mode)
Adjustments
Two push buttons and remote wire • Expert -style configuration (Static and Dynamic TEACH, light SET, dark SET and Windows SET) • Manually Adjust (+/–) sensitivity (from buttons only) • LO/DO, OFF-Delay, and response speed configurable (from buttons or remote wire) • Push-button lockout (from remote wire only) Factory Default Settings: Light Operate, Normal Speed, No Delay
Indicators
8-segment red bargraph* Green Status Indicators: LO, DO, High Speed (HS) and OFF-Delay Green LED: Power ON Yellow LED: Output conducting *See data sheet for detailed information
Construction
Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear polycarbonate cover.
Environmental Rating
IEC IP50, NEMA 1
Connections
PVC-jacketed 2 m or 9 m 6-wire integral cable, or integral 6-pin Pico-style quick-disconnect. QD cordsets are ordered separately. See page 229.
Operating Conditions
Temperature: -10° to +55° C
Installation
35 mm DIN rail or included mounting bracket
Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
FIBER SENSORS D10 D12 R55F PLASTIC FIBERS GLASS FIBERS
Main units: PVC-jacketed 2 m or 9 m 5-wire integral cable Sub-units: PVC-jacketed 2 m or 9 m 2-wire integral cable
Storage Temperature: -20° to +85° C
Relative humidity: 90% @ 55° C
Certifications Hookup Diagrams
Standard Models and Main Unit: DC08 (p. 717)
Sub-Units: DC09 (p. 718)
D10—Discrete Specifications Required Fiber Optic Cable
Banner P-Series plastic fibers (See Plastic Fiber Optic section, page 239)
Supply Voltage & Current
10 to 30V dc (10% max. ripple) @ less than 25 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltage
Output Configuration
Bipolar: 1 current sourcing (PNP) and 1 current sinking (NPN)
Output Rating
100 mA per output with short circuit protection OFF-state leakage current: less than 10 µA sourcing; 200 µA sinking ON-state saturation voltage: NPN: 1.6V @ 100 mA PNP: 2.0V @ 100 mA
Output Protection Circuitry
Protected against output short-circuit and false pulse on power up
Delay at Power-up
Max. 100 milliseconds; outputs do not conduct during this time
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
FIBER SENSORS
PLASTIC FIBERS
SENSORS
D10—Discrete Specifications
GLASS FIBERS
(cont’d)
Output Response Time
Standard models (with crosstalk avoidance circuitry): 500 microseconds High-speed models: 200 microseconds
Repeatability
Standard models: 95 microseconds High-speed models: 50 microseconds
Adjustments
12-turn Sensitivity potentiometer with relative position indicator; LO/DO Selection switch; 0 or 40 milliseconds OFF-delay switch NOTE: Use proper ESD techniques while making adjustments under cover.
Indicators
Two LEDs: Green and Yellow Green: Power ON Yellow: L ight Sensed Signal strength indicator See data sheet for detailed information
Construction
Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear polycarbonate cover.
Environmental Rating
IEC IP50; NEMA 1
Connections
PVC-jacketed 2 m or 9 m attached cable, or 4-pin Pico-style quick-disconnect fitting. QD cordsets are ordered separately. See page 229.
Operating Conditions
Temperature: -10° to +55° C Storage: -20° to +85° C Relative humidity: 90% @ 55° C (non-condensing)
Certifications Hookup Diagrams
DC04 (p. 716)
D10 Expert™ Small Object Counter—Numeric Display Specifications Required Fiber Optics
PFCVA models (Custom fiber arrays and mounting configurations are possible. Consult factory for assistance with your small object counting application.)
Sensing Beam
Visible red, 680 nm
Supply Voltage and Current
12 to 24V dc (10% maximum ripple) at less than 65 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltage
Output Configuration
2 NPN or 2 PNP, depending on model
Output Rating
150 mA maximum load OFF-state leakage current: < 10 µA at 24V dc ON-state saturation voltage: NPN < 1.5V at 150 mA load PNP < 2.5V at 150 mA load
Output Protection Circuitry
Protected against false pulse on power-up and continuous short-circuit
Output Response Time
Programmable, 150 µs, 225 µs, 300 µs
Delay at Power-up
Less than 1 second; outputs do not conduct during this time.
Adjustments
Push-button or remote programming of threshold offset percentage, light/dark operate, Dynamic Event Stretcher (DES), display, and power/speed
Indicators
Four-digit digital display, 2 arrow icons, push-button lockout, Dynamic Event Stretcher, light/dark operate selection and 2 amber output LEDs
Construction
Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear polycarbonate cover
Environmental Rating
NEMA 1; IEC IP50
Connections
PVC-jacketed 2 m or 9 m 6-wire integral cable or integral 6-pin Pico-style quick-disconnect. QD cordsets are ordered separately. See page 229. Temperature: -20° to +55° C Storage Temperature: -20° to +80° C Relative Humidity: 90% @ 50° C (non-condensing)
Operating Conditions
Installation
Number of Devices, Stacked
Ambient Temperature Rating
Load Specification
3
55° C
150 mA
7
50° C
50 mA
10
45° C
50 mA
35 mm DIN rail or included mounting bracket
Certifications Hookup Diagrams
DC18 (p. 720)
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Cordsets
Brackets
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
D10
Pico QD See page 656 Snap-on 4-Pin Length Straight Right-Angle 2m
PKG4-2
PKW4Z-2
—
9m
—
Snap-on 6-Pin Straight Right-Angle PKG6Z-2
PKW6Z-2
PKG6Z-9
PKW6Z-9
Measurement & Inspection Sensors pg. 608
pg. 650
DIN-35...
Additional cordset information available. See page 655.
Vision
pg. 650
SMBR55F01
SMBR55FRA
Wireless Indicators
Additional bracket information available. See page 601.
Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
Excess Gain Curves = Visible Red LED
(Diffuse-mode performance based on 90% reflectance white test card)
= Visible Green LED
Opposed Mode D10 Expert™ with Bargraph
Opposed Mode D10 Expert™ with Bargraph
1000
E X C E S S G A I N
1000
E X C E S S
100
10
G A I N
PIT26U PIT16U
1 1 mm (.04")
10 mm (0.4")
100 mm (4.0")
1000 mm (40.0")
DISTANCE
EGC-1
Range: Varies
1000
E X C E S S
100
10
G A I N
G A I N
G A I N
1000 mm 100 mm (40.0") 4.0"
10 mm (0.4")
100 mm (4.0")
DISTANCE
LED:
1000 mm (40.0")
EGC-6
E X C E S S
100
G
10
PBT26U
G A I N
I N
1 mm (.04")
PBT16U 110 mm (0.4") 0.1 mm (.004")
DISTANCE
EGC-3
100 mm (4.0") 1 mm (.04")
100
DISTANCE
Range: Varies LED:
10
1 10 mm (0.4")
G A I N
10 PIT66U PIT46U
E X C E S S G A I N
0.1 mm 100 (.004") mm
10 mm (0.4")
100 mm (4.0")
DISTANCE
Range: Varies LED:
1000 mm (40.0")
EGC-7
PBT66U 100
PBT46U
10
PBT46U
1 mm 1 (.04") 0.1 mm (.004")
(4.0")
EGC-4
10 mm (0.4") 1 mm
100 mm 10(4.0") mm
(.04")
DISTANCE
(0.4")
1000 mm 100 mm (40.0") 1000 mm (4.0") (40.0")
DISTANCE
Diffuse Mode D10 Expert™ with Bargraph 1000
E X C E S S
100
10
G A I N
PBT26U
1 0.1 mm (.004")
PBT66U
1000
1000
E X C E S S
1 mm (.04")
10 mm (0.4")
DISTANCE
Range: Varies LED:
D10 D12 R55F PLASTIC FIBERS
10000
Range: Varies LED:
Diffuse Mode D10 Expert™ with Bargraph
FIBER SENSORS
GLASS FIBERS
PBT26U
PBT16U A
1000 mm 40.0"
100
1 1 mm (.04")
10
0.1 mm (.004")
1000
PIT26U
Range: Varies
100 mm 10.0 mm (4.0") 0.4"
E X C E S S
1000
1
DISTANCE DISTANCE
E X C E S S
10
EGC-5
1 101.0mm mm (0.4") 0.04"
10000
1000
100
G A I N
PIT66U PIT46U fibers PIT46U
Opposed Mode D10 Expert™ with Bargraph
100
PIT16U 1 1 mm (.04")
PIT66U fibers
1 1 mm (.04")
1000
E X C E S S
100
Range: Varies LED:
Opposed Mode D10 Expert™ with Bargraph
E X C E S S
Opposed Mode
10
Diffuse Mode D10 Expert™ with Bargraph
1000
D10BFP
EGC-2
LED:
Diffuse Mode D10 Expert™ with Bargraph
100
PBT46U 1 0.1 mm (.004")
100 mm (4.0")
PBT66U
10
1 mm (.04")
EGC-8
10 mm (0.4")
100 mm (4.0")
DISTANCE
Range: Varies LED:
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS
PLASTIC FIBERS
Beam Patterns = Visible Red LED
(Diffuse-mode performance based on 90% reflectance white test card)
= Visible Green LED
Opposed Mode D10 Expert™ with Bargraph
SENSORS
GLASS FIBERS
Opposed Mode D10 Expert™ with Bargraph
Diffuse Mode D10 Expert™ with Bargraph
Diffuse Mode D10 Expert™ with Bargraph
100 mm
0.78"
200 mm
0.39"
0.39"
100 mm
0
0
10 mm
0.39"
0.39"
100 mm
20 mm
20 mm
0.78"
0.78"
30 mm
30 mm
1.18"
1.18"
0 10 mm
0
10 mm PIT16U0
PIT16U
12 mm 0 24 mm 12 mm36 mm 24 mm48 mm 36 mm60 mm 48 mm (0.47") (0.94") (0.47")(1.42") (0.94")(1.90") (1.42")(2.36") (1.90")
11.81"
PIT66U
7.87"
7.87"
3.93"
3.93"
0
0
100 mm
3.93"
3.93"
200 mm
200 mm
7.87"
7.87"
300 mm
300 mm
11.81"
11.81"
0
0
60 mm (2.36")
100 mm 0PIT46U
PIT46U
10 mm
PBT26U
5 mm 0 5 mm
0 PBT16U
PBT16U
0 0.19"
10 mm
10 mm
0.39"
100 mm
100 mm
0.59"
0
4 mm (0.15")
8 mm 0 (0.31")
4 mm 16 mm 8 mm 2012 mm 12 mm mm (0.15") (0.31") (0.47") (0.47") (0.63") (0.78")
DISTANCE
LED:
50 mm
0.39"
PBT66U
25 mm
0.19" 0
0
25 mm
0.19"
50 mm
0.39"
75 mm
0.59" 20 mm (0.78")
0 0.98"
50 mm
1.97"
1.97"
0
75 mm
2.95"
2.95"
DISTANCE
DISTANCE
LED:
Diffuse Mode D10 Expert™ with Bargraph
Diffuse Mode D10 Expert™ with Bargraph
2.36"
30 mm
1.0 mm
0.04"
20 mm
15 mm
0.59"
0.5 mm
0.02"
0
0.16"
4 mm 6 mm
0.23"
8 mm
0.31" 0
4 mm (0.16")
8 mm (0.31")
12 mm (0.47")
16 mm (0.63")
0
PIT46U
15 mm
0.59"
30 mm
1.18"
45 mm
1.77"
60 mm
2.36" 0
20 mm (0.78")
24 mm (0.71")
48 mm (1.42")
BP-6
Range: Varies LED:
72 mm (2.12")
0
0
PBT26U
0.5 mm
0.02"
1.0 mm
0.04"
1.5 mm
0.02" 0
96 mm 120 mm (2.83") (3.54")
1 mm (0.04")
2 mm (0.08")
3 mm (0.12")
4 mm (0.16")
5 mm (0.19")
1.18" PBT66U PBT46U
10 mm
0
10 mm
0.39"
20 mm
0.78"
30 mm
6 mm (0.23")
1.18" 0
DISTANCE
10 mm (0.39")
20 mm (0.78")
Range: Varies
LED:
30 mm (1.18")
DISTANCE
BP-8
BP-7
Range: Varies
LED:
0.78" 0.39"
0
DISTANCE
DISTANCE
BP-5
0
BEAM WIDTH
0.06"
1.18"
0.08"
PIT66U
BEAM WIDTH
1.5 mm
0.16"
2 mm
BEAM WIDTH
1.77"
4 mm
0.08"
DISTANCE
LED:
Range: Varies
30 mm
PIT16U
PBT46U
3.93" 3.93" mm mmmm 96160 mmmm128 mm 160 mm 640 mm 3296 mm 64128 (2.52") (1.26") (3.78") (2.52") (5.04") (3.78") (6.30") (5.04") (6.30")
32 mm (1.26")
45 mm
0
0.98"
0.98"
60 mm
2 mm
1.97"
25 mm
0.23"
PIT26U
6 mm
2.95"
0.98" 0
0 PBT46U
0.31"
8 mm
PBT66U
1.97"
100 mm
100 mm 16 mm (0.63")
25 mm
3.93"
2.95"
BP-4
Range: Varies
Opposed Mode D10 Expert™ with Bargraph
50 mm
0.19"
BP-3
Range: Varies
Opposed Mode D10 Expert™ with Bargraph
5 mm
5 mm
DISTANCE DISTANCE
BP-2
Range: Varies LED:
PBT26U
75 mm
0.59"
0.39"
10 mm
3.93"
100 mm
75 mm
0.59"
15 mm
80 mm 0 160 mm 320 mm 400 mm 80 mm240 mm 160 mm 240 mm 320 mm 400 mm (3.15") (6.30") (15.74") (3.15")(9.45") (6.30")(12.59") (9.45") (12.59") (15.74")
DISTANCE DISTANCE
BP-1
BEAM WIDTH
15 mm
11.81"
BEAM WIDTH
0.78"
10 mm
300 mm PIT66U 200 mm
BEAM WIDTH
300 mm
BEAM WIDTH
1.18"
BEAM WIDTH
PIT26U
BEAM WIDTH
1.18"
30 mm PIT26U 20 mm
BEAM WIDTH
20 mm
BEAM WIDTH
BEAM WIDTH
30 mm
Range: Varies
LED:
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
40 mm (1.57")
50 mm (1.97")
D12
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Complete Family of Plastic and Glass Fiber Optic Sensors
Measurement & Inspection Sensors
• Features LED bargraph that indicates signal strength, sensing contrast, programming status and diagnostic warnings, when not in high-speed mode • Available in glass and plastic fiber optic models • Includes marginal gain indicator with alarm output • Solves routine applications with economical standard models • Features high-speed sensing response and higher sensing power in some models • Excels in low-contrast applications with ac-coupled models • Features easy push-button TEACH-mode setup on D12E Expert™ models • Easily mounts to standard 35 mm DIN-rail mounting
Vision Wireless Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
30.0 mm
12.0 mm
FIBER SENSORS D10 D12 R55F PLASTIC FIBERS
12.0 mm
GLASS FIBERS
64.0 mm
30.0 mm
ONLINE AUTOCAD, STEP, IGES & PDF 70.0 mm
Glass Fiber Models Suffix FV and FVY M
D12 Expert™, 10-30V dc Sensing Mode/LED
Maximum Range
Visible Red LED
Switching Threshold Setting
Connection
Range varies by sensing mode and fiber optics used. See data sheet for maximum range specifications.
PLASTIC FIBER
Models NPN
Models PNP
D12EN6FV
D12EP6FV
D12E2N6FV
D12E2P6FV
Just above the “dark” condition
D12EN6FP
D12EP6FP
Midway between “dark” and “light” conditions
D12E2N6FP
D12E2P6FP
Just above the “dark” condition GLASS FIBER
AL
LO
7
DO
6
40
ms
0
5
ms
4
3
2
1
O
N
Plastic Fiber Models Suffix FP and FPY
Midway between “dark” and “light” conditions
2m
Connection options: A model with a QD requires a mating cordset (see page 235). For 9 m cable, add suffix W/30 to the 2 m model number (example, D12EN6FV W/30).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS 7
6
5
4
3
2
1
50S S 500
O
N
c
Sensing Mode/LED
Range
Visible Red LED
Connection
Output Response
2m
Models NPN
Models PNP
D12SN6FV
D12SP6FV
D12SN6FVQ
D12SP6FVQ
D12SN6FVY
D12SP6FVY
D12SN6FVYQ
D12SP6FVYQ
D12SN6FVY1†
D12SP6FVY1†
D12SN6FVY1Q†
D12SP6FVY1Q†
D12SN6FP
D12SP6FP
4-Pin Pico Pigtail QD
D12SN6FPQ
D12SP6FPQ
2m
D12SN6FPY
D12SP6FPY
D12SN6FPYQ
D12SP6FPYQ
D12SN6FPY1†
D12SP6FPY1†
D12SN6FPY1Q†
D12SP6FPY1Q†
Excess Gain EGC-1 & EGC-2 (p. 235)
500 µs 4-Pin Pico Pigtail QD
GLASS FIBER HIGH-SPEED
Range varies by sensing mode and fiber optics used
2m 4-Pin Pico Pigtail QD 2m
GLASS FIBER
Selectable 50 µs or 500 µs***
4-Pin Pico Pigtail QD 2m
EGC-3 & EGC-4 (p. 235)
EGC- 5 & EGC-6 (p. 235)
500 µs PLASTIC FIBER HIGH-SPEED
Range varies by sensing mode and fiber optics used
4-Pin Pico Pigtail QD 2m
PLASTIC FIBER
Selectable 50 µs or 500 µs***
4-Pin Pico Pigtail QD
EGC-7 & EGC-8 (p. 235)
7
6
5
4
3
2
1
O
N
c
D12 High-Power, 10-30V dc Connection
Range varies by sensing mode and fiber optics used
2m
Models NPN
Models PNP
Excess Gain
D12SN6FPH
D12SP6FPH
D12SN6FPHQ
D12SP6FPHQ
EGC- 9 & EGC-10 (p. 235)
500 µs 4-Pin Pico Pigtail QD
O
LO DO
N
IN
PLASTIC FIBER
Output Response
c
Range
GA
Sensing Mode/LED
Visible Red LED
CK LO
SENSORS
D12 and D12 High-Speed, 10-30V dc
D12 AC-Coupled, 10-30V dc Sensing Mode/LED
Range
Visible Red LED
Connection
Output Type
Output Response
2m GLASS FIBER
Range varies by Power Level/Speed Selection used and with fiber optics used. See data sheet for range information.
PLASTIC FIBER
4-Pin Pico Pigtail QD 2m 4-Pin Pico Pigtail QD
Models D12DAB6FV
Bipolar NPN/PNP
D12DAB6FVQ 50 µs D12DAB6FP D12DAB6FPQ
Connection options: A model with a QD requires a mating cordset (see page 235). For 9 m cable, add suffix W/30 to the 2 m model number (example, D12SN6FV W/30). † Y1 models have 20 milliseconds output pulse stretcher. *** When 50 microseconds is selected, bargraph is disabled.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
D12 Expert™ Specifications Supply Voltage and Current
10 to 30V dc at 45 mA max. (exclusive of load); 10% max. ripple
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
NPN open collector (both outputs) or PNP open collector (both outputs), depending on model Load output: Normally open and programmable Light or Dark-Operate; Alarm output: Normally open 150 mA max. each output OFF-state leakage current: less than 10 µA at 30V dc ON-state saturation voltage: less than 1 volt at 10 mA dc; less than 1.5 volts at 150 mA dc The total load may not exceed 150 mA
Output Rating
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Indicators Safety Light Screens
Output Protection Circuitry
Protected against false pulse on power-up and short circuit of outputs (trips at 175 mA)
Safety Laser Scanners
Output Response Time
200 microseconds ON/OFF (40 milliseconds OFF when OFF-delay selected) NOTE: False pulse protection circuit causes a 0.1 second delay on power-up
Fiber Optic Safety Systems
Output Operation Mode
Light operate or dark operate: selected by push button
Safety Controllers & Modules
Output Timing Functions
ON/OFF (no delay) or fixed 40 millisecond OFF-delay; selected by push button
Safety Two-Hand Control Modules
Repeatability
66 microseconds
Safety Interlock Switches
Adjustments
Push-button TEACH-mode sensitivity setting; Remote teaching input is provided
Indicators
Green: power ON and flashes when ready for teach mode Yellow: output conducting 7-segment moving dot red LED See data sheet for detailed information
Emergency Stop Devices
Mounting Bracket
D12 Sensors mount directly to a standard DIN rail, or may be through-hole mounted using the supplied mounting bracket and M3 x 0.5 hardware
Construction
Black ABS housing with acrylic cover, stainless steel M3 x 0.5 hardware for use with thermoplastic polyester mounting bracket (supplied); the plastic fiber clamping element is acetal
Environmental Rating
IEC IP11; NEMA 2
Connections
PVC-jacketed 2 m or 9 m cables, or 150 mm pigtail with 4-pin Pico-style quick-disconnect (QD) are available. QD cordsets are ordered separately. See page 235.
Operating Conditions
Temperature: -20° to +70° C
FIBER SENSORS D10
Relative humidity: 90% at 50° C (non-condensing)
D12 R55F PLASTIC FIBERS GLASS FIBERS
Certifications (except D10E2) Hookup Diagrams
DC19 (p. 720)
D12 Standard, High-Speed and High-Power Specifications Supply Voltage and Current
10 to 30V dc at 45 mA max. (exclusive of load)
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
Output Rating
Outputs are NPN (sinking) or PNP (sourcing), depending on model Complementary: one normally open (NO) and the other normally closed (NC); NC output may be wired as diagnostic alarm output by reversing power supply connections except high speed “Y” and “Y1” suffix models (see hookups) 150 mA max. each output OFF-state leakage current: less than 10 µA at 30V dc ON-state saturation voltage: less than 1 volt at 10 mA dc; less than 1.5 volts at 150 mA dc The total load may not exceed 150 mA
Output Protection Circuitry
Protected against false pulse on power-up and short circuit of outputs
Output Response Time
Standard and High-Power Models: 500 microseconds ON/OFF High-Speed Models: selectable 50 or 500 microseconds ON/OFF NOTE: False pulse protection circuit causes a 0.1 second delay on power-up
Output Timing Functions
“Y1” models have fixed 20 milliseconds pulse stretcher (OFF-delay) when 50 microseconds mode is used
Repeatability
130 microseconds; “Y” and “Y1” models have selectable 50 microseconds/500 microseconds response; repeatability in 50 microseconds mode is 15 microseconds
Adjustments
15-turn adjustment sensitivity; “Y” and “Y1” (high speed models) also have a response mode selector switch
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
SENSORS
D12 Standard, High-Speed and High-Power Specifications
(cont’d)
Indicators
Two top-mounted LED indicators, one yellow and one green, and one 7-segment red LED moving dot bargraph; Note that the 7-segment bargraph and marginal excess gain indication (bargraph segment #7) are inoperative in the 50 µs response mode of “Y” and “Y1” models Green LED lights for DC Power ON Yellow LED lights for normally open output conducting On all models in 500 microseconds response mode, the 7-segment moving dot red LED bargraph lights to indicate relative received light signal strength; On all models in 50 and 500 microseconds response mode, segment #1 flashes to indicate OUTPUT OVERLOAD; On all models in the 500 microseconds response mode, segment #7 flashes to indicate MARGINAL EXCESS GAIN; On standard and high power models, a flashing LED corresponds to the “ON” state of the alarm output; (Alarm output not available on Y & Y1 models)
Mounting Bracket
D12 Sensors mount directly to a standard DIN rail, or may be through-hole mounted using the supplied mounting bracket and M3 x 0.5 hardware
Construction
Black ABS housing with acrylic cover, stainless steel M3 x 0.5 hardware for use with thermoplastic polyester mounting bracket (supplied); the plastic fiber clamping element is acetal
Environmental Rating
IEC IP11; NEMA 2
Connections
PVC-jacketed 2 m or 9 m cables, or 150 mm pigtail with 4-pin Pico-style quick-disconnect (QD) are available. QD cordsets are ordered separately. See page 235.
Operating Conditions
Temperature: -20° to +70° C
Relative humidity: 90% at 50° C (non-condensing)
Certifications Hookup Diagrams
NPN Models: DC05 (p. 717)
PNP Models: DC06 (p. 717)
D12 AC-Coupled Specifications Supply Voltage and Current
10 to 30V dc at 60 mA max. (exclusive of load)
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
Bipolar: one NPN (current sinking) and one PNP (current sourcing) open-collector transistor
Output Rating
150 mA max. each output OFF-state leakage current: less than 10 µA at 30V dc ON-state saturation voltage: less than 1 volt at 10 mA dc; less than 1.5 volts at 150 mA dc The total load may not exceed 150 mA
Output Protection Circuitry
Protected against false pulse on power-up and short circuit of outputs
Output Response Time
50 microseconds ON/OFF (NOTE: False pulse protection circuit causes a 0.1 second delay on power-up)
Output Operation Mode
Light operate or dark operate: selected by switch
Output Timing Functions
Pulse output; adjustable from 1 to 70 milliseconds
Repeatability
15 microseconds ON
Adjustments
Three top-panel controls: SENSITIVITY control (15-turn slotted brass screw, clutched at both ends of adjustment), a light- or dark-operate select switch, and an OUTPUT PULSE adjustment (3/4-turn potentiometer)
Indicators
Three top-mounted LED indicators: Green LED: Lights to indicate dc Power ON Yellow LED: Lights for Output Conducting Red LED: Lights whenever AGC system is locked onto the signal
Mounting Bracket
D12 Sensors mount directly to a standard DIN rail, or may be through-hole mounted using the supplied mounting bracket and M3 x 0.5 hardware
Construction
Black ABS housing with acrylic cover, stainless steel M3 x 0.5 hardware for use with thermoplastic polyester mounting bracket (supplied); the plastic fiber clamping element is acetal
Environmental Rating
IEC IP11; NEMA 2
Connections
PVC-jacketed 2 m or 9 m cables, or 150 mm pigtail with 4-pin Pico-style quick-disconnect (QD) are available. QD cordsets are ordered separately. See page 235.
Operating Conditions
Temperature: -40° to +70° C
Application Note
D12 AC-coupled sensors should not be used in areas of known electrical “noise” or RF fields.
Relative humidity: 90% at 50° C (non-condensing)
Certifications Hookup Diagrams
DC04 (p. 716)
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Cordsets
Brackets
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
D12
Pico QD See page 656 Snap-on 4-Pin Length Straight Right-Angle 2m
PKG4-2
Measurement & Inspection Sensors
PKW4Z-2 pg. 608
pg. 650
DIN-35...
Vision
pg. 650
SMBR55F01
SMBR55FRA
Wireless Indicators
Additional bracket information available. See page 601.
Additional cordset information available. See page 655.
Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules
Excess Gain Curves
Safety Two-Hand Control Modules
(Diffuse-mode performance based on 90% reflectance white test card)
Safety Interlock Switches
= Visible Red LED
Opposed Mode—Glass Fiber D12 Standard 1000
3
ms
ON ms
2
0
0
ON 1
ms
ms 40
DO LO ALM
7
4
5
40
6
DO
5
w/IT23S Fibers
w/IT13S Fibers
10
4
6
LO
100 3
ALM
E X C E S S
Opposed mode
2
7
G A I N
1000
D12FV models
1
E X C E S S
Diffuse Mode—Glass Fiber D12 Standard
G A I N
1 1 mm (0.04")
10 mm (0.4")
100 mm (4.0")
DISTANCE
EGC-1
1000
D12FV models
E X C E S S
Diffuse mode w/BT23S Fiber
100
w/BT13S Fiber
G A I N
10
1 0.1 mm (0.004")
1000 mm (40")
Opposed Mode—Glass Fiber D12 High Speed
1 mm (0.04")
10 mm (0.4")
DISTANCE
EGC-2
1000
D12 FVY & FVY1 models
E X C E S S
Opposed mode 100 w/IT23S Fibers 10
w/IT13S Fibers
G A I N
1 1 mm (0.04")
100 mm (4")
Diffuse Mode—Glass Fiber D12 High Speed
10 mm (0.4")
100 mm (4.0")
1000 mm (40")
DISTANCE
EGC-3
Emergency Stop Devices
D12FVY & FVY1 models Diffuse mode
100
10
w/BT23S Fiber
w/BT13S Fiber
FIBER SENSORS D10
1 0.1 mm (0.004")
1 mm (0.04")
EGC-4
10 mm (0.4")
100 mm (4")
DISTANCE
D12 R55F PLASTIC FIBERS
Range: Varies
LED:
Range: Varies LED:
Opposed Mode—Plastic Fiber D12 Standard
10 mm (0.4")
100 mm (4.0")
c
ON ms 0 ms 40
DO LO ALM
c
7
ON
ON
DO
6
1
1
5
2
2
4
40
ms
0
ms
3
3
3
2
4
4 5 6 7
ON 1
EGC-9
Range: Varies
10 mm (0.4")
100 mm (4")
DISTANCE
100 mm (4.0")
DISTANCE
E X C E S S G A I N
PIT26U Fibers
LED:
1.0 mm (0.04")
1000
D12FPH Series Sensors
10 mm (0.4")
1
1000
D12FPY & FPY1 models
E X C E S S
Opposed mode
100
PIT46U Fibers 10
G A I N
PIT26U Fibers 1 1.0 mm (0.04")
EGC-7
Diffuse Mode—Plastic Fiber D12 High Speed
10 mm (0.4")
100 mm (4.0")
DISTANCE
Range: Varies LED:
1000 mm (40")
D12FPY & FPY1 models Diffuse mode
100
PBT46U Fiber
10
PBT26U Fiber 1 0.1 mm (0.004")
EGC-8
1.0 mm (0.04")
10 mm (0.4")
100 mm (4")
DISTANCE
Range: Varies LED:
Diffuse Mode—Plastic Fiber D12 High Power
1 1.0 mm (0.04")
PBT26U Fiber
0.1 mm (0.004")
100
10
G A I N
10
Range: Varies LED:
PIT46U Fibers
E X C E S S
100
EGC-6
LED:
PBT46U Fiber
GLASS FIBERS
Range: Varies LED:
Opposed Mode—Plastic Fiber D12 High Speed 1000
D12FP models Diffuse mode
1000 mm (40")
DISTANCE
1000
5
7
1
Opposed Mode—Plastic Fiber D12 High Power
6
6
PIT26U Fibers
Range: Varies
7
5
G A I N
10
EGC-5
G A I N
4
PIT46U Fibers
3
LO
100
1.0 mm (0.04")
E X C E S S
E X C E S S
Opposed mode
2
ALM
D12FP models
1
G A I N
Diffuse Mode—Plastic Fiber D12 Standard 1000
1000
E X C E S S
Range: Varies LED:
100 PBT46U Fiber
10
PBT26U Fiber 1 1 mm (0.04")
1000 mm (40")
EGC-10
D12FPH Series Sensors
10 mm (0.4")
100 mm (4.0")
1000 mm (40")
DISTANCE
Range: Varies LED:
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
R55F
• Delivers outstanding color contrast sensitivity • Features innovative TEACH function with two options for setting the sensing threshold • Reliably detects 16 levels of grayscale at up to 10,000 actuations per second • Available in two fiber types: economical plastic for repeated flexing and glass for harsh conditions • Easily mounts in confined areas, either flat or to 35 mm DIN rail • Provides bipolar (NPN/PNP) outputs with delay settings of 0, 20 and 40 milliseconds • Clearly displays relative received signal strength with 10-element indicator bargraph
85.4 mm
25.0 mm
–
30.0 mm
P
TU
SE
+
SENSORS
Glass or Plastic Fiber Optic Sensors
R55F Fiber Optic, 10-30V dc Sensing Mode/LED
Range
Infrared LED
Connection
Output Type
Range varies by sensing mode and fiber optics used.
GLASS FIBER
5-pin Euro QD 2m 5-pin Euro QD
Models R55F
2m GLASS GLASSFIBER FIBER
Visible Red LED
Bipolar NPN/PNP
R55FQ R55FV R55FVQ
Connection options: A model with a QD requires a mating cordset (see page 238). For 9 m cable, add suffix W/30 to the 2 m model number (example, R55F W/30).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
– P
TU
+
SE
R55F Fiber Optic, 10-30V dc Sensing Mode/LED
Range
Visible Green LED
Connection
Visible Blue LED
Output Type
Visible White LED
Visible Red LED
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors
Models
Vision Wireless
R55FVG
2m
R55FVGQ
5-pin Euro QD
GLASS GLASSFIBER FIBER
Indicators Safety Light Screens Safety Laser Scanners
R55FVB
2m GLASS GLASSFIBER FIBER
5-pin Euro QD
R55FVBQ
2m
R55FVW R55FVWQ
5-pin Euro QD
GLASS FIBER GLASS FIBER
Range varies by sensing mode and fiber optics used. PLASTIC FIBER
2m 5-pin Euro QD
Bipolar NPN/PNP
2m 5-pin Euro QD
PLASTIC PLASTIC FIBER FIBER
Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
R55FP R55FPQ R55FPG R55FPGQ
FIBER SENSORS D10 D12
2m
R55FPB
R55F PLASTIC FIBERS GLASS FIBERS
GLASS PLASTICFIBER FIBER
5-pin Euro QD
R55FPBQ
2m
R55FPW
5-pin Euro QD
PLASTIC PLASTIC FIBER FIBER
R55FPWQ
Connection options: A model with a QD requires a mating cordset (see page 238). For 9 m cable, add suffix W/30 to the 2 m model number (example, R55F W/30).
R55F Fiber Optic Specifications Supply Voltage and Current
10 to 30V dc (10% max. ripple) at less than 70 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor
Output Rating
150 mA max each output @ 25° C (derate ≈ 1 mA per ° C increase) OFF-state leakage current: less than 5 µA @ 30V dc ON-state saturation voltage: PNP: less than 1V @ 10 mA; 1.5V @ 150 mA NPN: less than 200 mV @ 10 mA; 1V @ 150 mA
Output Protection Circuitry
Protected against false pulse on power-up and continuous overload or short-circuit of outputs
Output Response Time Delay at Power-up
50 microseconds 100 milliseconds; outputs do not conduct during this time.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
R55F Fiber Optic Specifications Adjustments
SENSORS
Using push buttons (“+” Dynamic and “-” Static): Manually adjust Switch Point using “+” or “-” buttons Dynamic TEACH (teach on-the-fly) sensitivity adjustment Static TEACH sensitivity adjustment Static Single-Point TEACH Light operate/Dark operate OFF-Delay select: 0 milliseconds, 20 milliseconds or 40 milliseconds Using Remote TEACH input (gray wire): Dynamic TEACH (teach on-the-fly) sensitivity adjustment Static TEACH sensitivity adjustment Static Single-Point TEACH Light operate/Dark operate OFF-Delay select: 0 milliseconds, 20 milliseconds or 40 milliseconds Push button lockout for security 10-segment (Green) light bar indicates signal strength Light Operate (Green) Dark Operate (Green) Outputs Conducting (Yellow) OFF-Delay (Green): SETUP Mode: OFF–no delay Flashing–20 milliseconds delay ON–40 milliseconds delay
Indicators
RUN Mode: OFF–no delay ON–20 or 40 milliseconds delay
Construction
Black ABS/polycarbonate blend; nylon fiber clip mounts to standard 35 mm DIN rail. 1 stainless steel right angle bracket and 1 PBT polyester bracket for mounting to flat surfaces also included with sensor.
Environmental Rating
IEC IP67; NEMA 6
Connections
2 m or 9 m PVC-jacketed 5-conductor cable, or 5-pin Euro-style quick-disconnect (QD) fitting. QD cordsets are ordered separately. See page 238. Fibers: Fiber clip (no tool required)
Operating Conditions
Temperature: -10° to +55° C Relative humidity: 90% at 50° C (non-condensing)
Application Notes
• Do not mount the fiber tip directly perpendicular to shiny surfaces; position it at approximately a 15° angle in relation to the sensing target. • Minimize web or product “flutter” whenever possible to maximize sensing reliability.
Certifications Hookup Diagrams
DC08 (p. 717)
Cordsets
Brackets
Euro QD
R55F
See page 661 Length
Threaded 5-Pin Straight Right-Angle
2m
MQDC1-506
MQDC1-506RA
5m
MQDC1-515
MQDC1-515RA
9m
MQDC1-530
MQDC1-530RA
Additional cordset information available. See page 655.
pg. 608
pg. 650
DIN-35...
SMBR55F01
pg. 650 SMBR55FRA
Additional bracket information available. See page 601
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Plastic Fiber Optics • Provide an economical alternative to glass fiber optics for piping photoelectric sensing light to and from confined areas with suitable environments • Ideal for detecting small objects • Withstand repeated flexing and bending • Available in individual or bifurcated styles* • Available with optional DURA-BEND™ fibers for improved flexibility in difficult-to-access locations, without the decreased performance to which excessively bent standard plastic fibers optics are prone • Available with core diameters of 0.25, 0.50, 0.75, 1.0 and 1.5 mm
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
Plastic Fiber Optic Model Key P B P 4 6 U C X PLASTIC FIBER FAMILY designator
MODIFICATIONS designator
Same for all plastic fibers
“MXX” = Sensing end tip modification
ASSEMBLY STYLE designator
CONTROL END designator
B = Bifurcated fiber I = Individual fiber* DI = Dual Individual fiber*
T5 = Terminated TMB5 = STEELSKIN™ braiding over monocoil reinforcement U = Unterminated straight cable** UC = Unterminated Coiled cable UHF = Unterminated DURA-BEND™ multi-core cable
SENSING END designator A = 90° Angle AT = 90° Angle/Thread CF = Coaxial Ferrule CT = Coaxial Thread E = Encapsulated EFP = Extended Ferrule Probe F = Ferrule FM = Ferrule Miniature FMP = Ferrule Miniature Probe L = Lensed P = Probe PF = Probe Ferrule PMSB = Probe Miniature Side-view Bendable PS = Probe Side-view PSB = Probe Side-view Bendable PSM = Probe Side-view Miniature R = Rectangular RS = Rectangular Side-view T = Thread TA = Thread/90° Angle TP = Thread/Probe
FIBER LENGTH designator 3 = 1 m (1000 mm) 6 = 2 m (2000 mm) 100 = 30 m (30480 mm)
FIBER CORE DIAMETER designator 1 = 0.25 mm 2 = 0.50 mm 3 = 0.75 mm 4 = 1.00 mm 6 = 1.50 mm 1X4 = 4 x 0.25 mm 1X16 = 16 x 0.265 mm 1X32 = 32 x 0.265 mm
* All individual plastic fiber optics are sold and used in pairs. Bifurcated fibers are two-way fibers with a single sensing end that both emits and receives light and with dual-control sensor ends that attach separately to the sensor’s LED and photodetector. ** Plastic fibers with “U” in the suffix of the model numbers have unterminated control ends; cut them to the required length using the supplied cutter.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS PLASTIC FIBERS GLASS FIBERS
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
SENSORS
Plastic Fiber Optics Specifications Construction
Optical Fiber: acrylic (PMMA) monofilament, except as noted Protective Jacket: black polyethylene, except as noted Threaded End Tips and Hardware: nickel-plated brass, except as noted Probe End Tips: annealed (bendable) 304 stainless steel Angled End tips: hardened 304 stainless steel Ferrule End Tips: 303 stainless steel
Sensing Range
Refer to the specific fiber optic/sensor combination
Implied Dimensional Tolerance
All dimensions are in millimeters: x = ±2.5 mm, x.x = ±0.25 mm and x.xx = ±0.12 mm, unless specified. “L” = ±40 mm per meter
Minimum Bend Radius
8 mm for 0.25 mm diameter fibers 12 mm for 0.5 mm diameter fibers (except DURA-BEND™) 25 mm for 1.0 mm diameter fibers (except DURA-BEND™) 38 mm for 1.5 mm diameter fibers
Repeat Bending/Flexing
Life expectancy of plastic fiber optic cable is in excess of one million cycles at bend radii of no less than the minimum and a bend of 90° or less. Avoid stress at the point where the cable enters the sensor (“control end”) and at the sensing end tip. Coiled plastic fiber optic assemblies are recommended for any application requiring reciprocating fiber motion.
Chemical Resistance
The acrylic core of the monofilament optical fiber will be damaged by contact with acids, strong bases (alkalis) and solvents. The polyethylene jacket will protect the fiber from most chemical environments. However, materials may migrate through the jacket with long term exposure. Samples of fiber optic material are available from Banner for testing and evaluation.
Temperature Extremes
Temperatures below -30° C will cause embrittlement of the plastic materials but will not cause transmission loss. Temperatures above +70° C will cause both transmission loss and fiber shrinkage.
Operating Temperature
-30° to +70° C, unless otherwise specified
!
APPLICATION NOTES AND WARNINGS !
1
Plastic fiber assemblies with “U” in the suffix of the model numbers have unterminated control ends (the end that is coupled to the photoelectric sensor). The customer can cut these fiber optic assemblies to the required length using the supplied cutter. Use only the supplied cutter to ensure optimal light coupling efficiency.
2
Terminated plastic fiber assemblies are optically ground and polished and cannot be shortened, spliced or otherwise modified.
3
Do not subject the plastic fibers to sharp bends, pinching, high tensile loads or high levels of radiation.
4
When ordering fiber lengths in excess of 2 m, take into account light signal attenuation due to the additional length.
5
Due to their light transmission properties, plastic fiber optics are recommended for use only with visible light fiber optic sensors.
6
Use caution when applying fiber optics in hazardous locations. Although fiber optic assemblies are, by themselves, intrinsically safe, the sensor and associated electronics must be LOCATED IN A SAFE ENVIRONMENT. Alternatively, fiber optics may be used with NAMUR sensor model Q45AD9FP (page 196). Fiber optics do not necessarily provide a hermetic seal between a hazardous environment and the safe environment.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Model Number
2X ø 1.0
stainless steel
PBF16U
polyethylene
PBF26U
0.5
PBF46U
stainless steel
polyethylene
PBF46UM3MJ1.3
stainless steel
PBF66U
stainless steel
1.5
M3 x 0.5 stainless steel
PBFM16U
2X ø 1.0
80
100
120
140
160
Safety Controllers & Modules
Safety Interlock Switches 50
100
150
200
250
300
25
50
100
150
200
250
300
Emergency Stop Devices
• Smooth ferrule; thin jacket (ø 1.3)
38
• Smooth ferrule; long range
FIBER SENSORS PLASTIC FIBERS 100
ø 0.5 stainless steel (non-bendable) ferrule
0.25 2000
60
• Smooth ferrule
17.0
polyethylene
40
ø 5.1
2000
PBFM46U
25
17.0
polyethylene
Safety Light Screens
ø 3.0
2000
15.0
8
200
300
400
500
GLASS FIBERS
• Non-bendable miniature tip
15.0
5
10
15
20
25
30
50
100
150
200
250
300
5
10
15
20
25
30
ø 5.1
stainless steel
ø 3.05
1.0 2000 2X ø 1.0
25
• Smooth ferrule
17.0
14.0
M3 x 0.5 stainless steel
polyethylene
0.25
8
• Thread
11.0
2000
2X ø 1.0
M3 x 0.5 nickel plated brass
polyethylene
0.5
12
• Thread 20
11.0
2000
M6 x 0.75 nickel plated brass
2000 2X ø 2.2
30
Safety Two-Hand Control Modules
1.0
polyethylene
25
Fiber Optic Safety Systems
17.0
2X ø 1.3
2X ø 2.2
20
ø 5.1
polyethylene
polyethylene
15
• Smooth ferrule 20
1.0
2X ø 2.2
PBT16U
12
16.0
2X ø 2.2
10
ø 4.1
2000
PBT26U
Indicators
• Smooth ferrule
Safety Laser Scanners
stainless steel
polyethylene
2X ø 2.2
PBT46U
8
5
polyethylene
Vision
16.0
2000
PBT66U
Typical Range (mm)
Wireless
0.25
2X ø 1.0
Standard
Features
ø 3.0
2000
Diffuse
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
Measurement & Inspection Sensors
Free Cut*
60
80
100
120
140
160
ø 4.0
1.0 14.0
M6 x 0.75 nickel plated brass
25
• Thread 50
3.0
100
150
200
250
300
ø 4.0
1.5 2000
40
14.0
3.0
38
• Thread; long range 100
200
300
400
500
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
PLASTIC FIBERS
PBFMP16UMP.2 PBEFP26U
Model Number
stainless steel
polyethylene
PBP16U
ø 1.65
2000
15.0
2X ø 1.0
M3 x 0.5 nickel plated brass
PBP26U PBP46U PBPF26U PBPMSB36U PBPF26UMB
• Smooth ferrule; non-bendable tip 20
40
60
80
100
120
140
160
8
• Smooth ferrule; non-bendable tip
5.0
5
10
15
20
25
30
5
10
15
20
25
30
annealed stainless steel (bendable) probe
ø 0.81
0.25
10.0
5.0 bendable
8
• Thread; bendable tip
area
11.0
M3 x 0.5 nickel plated brass
polyethylene
2000
63
ø 1.47
annealed stainless steel (bendable) probe
11.0 M6 x 0.75 nickel plated brass
polyethylene
0.5
ø 1.65
5.0 bendable
0.5
2.0
3.0
ø 1.27
15.0
10.0
annealed stainless steel (bendable) probe
0.5
0.75 area
2000
2000
stainless steel (non-bendable) probe
polyethylene
2000
12
3.0
1.0
300
60
80
100
120
140
160
20
40
60
80
100
120
140
160
10
20
30
40
50
60
70
80
• Smooth ferrule; bendable tip
• Smooth ferrule; bendable tip
25
ø 3.0
ø 5.1
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
30
40
50
3.0
25
60
80
100
120
140
160
20
40
60
80
100
120
140
160
50
100
150
200
250
300
350
400
3.0 2.5
51
40
• Thread; non-bendable tip
51
ø 3.8
20 3.2
1.5 14.0
20
• Smooth ferrule; bendable tip
51
stainless steel (non-bendable) probe
stainless steel (non-bendable) probe stainless steel
250
3.2
ø 3.0
14.0
2X ø 2.2
200
40
10
1.0 2000
150
20
51
14.0 M6 x 0.75 nickel plated brass
2X ø 2.2 polyethylene
2.5
0.5
stainless steel
20
10.0
ø 1.47
14.0 ø 5.1
100
3.0
ø 3.2 stainless steel
2X ø 2.2
160
• Flat mounting block; bendable tip
65
15.0
2000
12
2.30
5.0 bendable
polyethylene
140
2.50
ø 2.1
stainless steel
polyethylene
120
• Thread; bendable tip
2X ø 0.5
65
ø 4.8
2X ø 2.2
100
annealed stainless steel (bendable) probe
ø 1.65
2.0
polyethylene
12
65
aluminum
2000
80
• Thread; bendable tip 50
10.0
area
2X ø 3.4
60
annealed stainless steel (bendable) probe ø 1.27
15.0
2X ø 1.0
25
89.0
M4 x 0.7 stainless steel
polyethylene
40
annealed stainless steel (bendable) probe
17.0
2000
• Thread; bendable tip 20
1.0
polyethylene
12
89 ø 3.0
2X ø 1.0
PBPS26U
Typical Range (mm)
ø 0.82
15.0
2X ø 1.0
PBPS46U
Free Cut*
ø 3.0
2000
polyethylene
12
2.0
0.25
2000
PBPS46UMT
20.0
stainless steel
polyethylene
2X ø 2.2
PBPS66U
ø 1.27
0.5
2000
Probe
Features
ø 4.0
2X ø 1.0
2X ø 1.0
Side-View
GLASS FIBERS
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
2X ø 1.0
Diffuse
SENSORS
FIBER SENSORS
38
• Smooth ferrule; non-bendable tip
More on next page
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
PBCF21X46U PBAT46UHFMTA
Right-Angle
Model Number
Drawing & Dimensions (mm) M4 X 0.7 stainless steel 2X ø 2.2
2 jam nuts and 1 ITLW included 7.0 ø 7.9
Polyethylene
2000
PBCF46U PBCT21X46U PBCT26U PBCT26UM4M2.5 PBCT26UM3
Coaxial
PBCT46U PBFM1X43T5 PBP46UC
Typical Range (mm)
Vision Wireless
1.0
19.1
2
Indicators
• Right Angle, threaded, stainless steel 90
135
180
225
ø 3.0
polyethylene
stainless steel
Fiber Optic Safety Systems
ø 2.0
0.5 4X 0.25
2000
15.0
12
• Miniature probe tip 20
15.0
stainless steel
40
60
80
100
120
1.0 16X 0.265 2000 2X ø 1.0
Safety Interlock Switches
0.5 4X 0.25
12
100
150
200
250
300
350
Emergency Stop Devices
• Miniature thread 20
12.0
40
60
80
100
120
M4 x 0.7 stainless steel
polyethylene
0.5 9X 0.25 2000
12
• Thread
ø 3.0
polyethylene
2000
M3 x 0.5 stainless steel
5.0
2X ø 1.25
0.5 9X 0.25 11.0
M6 x 0.75 nickel plated brass
2X ø 2.2
2000
20
40
60
80
100
120
140
160
180
20
40
60
80
100
120
140
160
180
20
40
60
80
100
120
140
160
180
GLASS FIBERS
• Miniature thread
M2.5 x 0.045
2000
polyethylene
12
13.0
M4 x 0.7 stainless steel
polyethylene
0.5 9X 0.25
FIBER SENSORS PLASTIC FIBERS
18.0 2X ø 1.25
12
• Thread
3.0
ø 4.0
1.0 16X 0.265 14.0
25
• Thread 50
3.0
100
150
200
250
300
350
PVC with monocoil
ø 1.88
polyethylene
ø 1.0
stainless steel
4X 0.25
15.5
• Smooth ferrule 50
M3 x 0.5 stainless steel
2000
ø 4.6
25
17.0
polyethylene
Safety Controllers & Modules Safety Two-Hand Control Modules
ø 5.1
polyethylene
ø 2.2
Safety Light Screens Safety Laser Scanners
2X ø 1.0
8
15.0
24.5
30.0 152
• Best for repetitive flexing (1,000s of cycles)
10
20
30
40
50
1000 polyethylene 2X ø 2.2
annealed ss (bendable) probe
ø 3.0
M6 x 0.75 nickel plated brass
1.0
ø 23
200
2000 fully extended
280
polyethylene
PBT46UC
Free Cut*
45
2X ø 1.25
High-Flex
Features
2000
2X ø 2.2
Diffuse
Core 6.35 Dia. Min. Bend Radius (mm) (mm)19.1
6.35
M4 X 0.7 stainless steel 2 jam nuts and 1 ITLW included
2X ø 2.2
Measurement & Inspection Sensors
7.0
ø 7.9
Polyethylene
2X ø 2.2
17.0
2000 fully extended
M6 x 0.75 nickel plated brass
20
40
60
80
100
120
20
40
60
80
100
120
ø 4.0
1.0 280
• For applications involving reciprocating motion
89.0
ø 23
200
25
17.0
25
• For applications involving reciprocating motion
3.0
NA: WORLD-BEAM QS18 not recommended. NA: MINI-BEAM Expert not recommended. * Fibers can be free cut using fiber cutter (see page 255).
Indicates lens available for model. See page 247 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
PLASTIC FIBERS
PLI-A10
2000
PBP46UHF PBFM46UHF PBPS46UHF PBT26UHF
DURA-BEND™
PBT46UHF PBRS1X326U PBR1X326U
Area Sensing (Array)
anodized aluminum knurled locking ferrule
ø 3.0 smooth ferrule stainless
polyethylene
GLASS FIBERS
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm) 2X ø 1.25
PBF46UHF
Convergent Beam Spot
Model Number
Diffuse
SENSORS
FIBER SENSORS
M6 x 0.75 anodized aluminum
0.5 9X 0.25
12
• Anodized AL tip; ø 0.5-3.2 mm beam spot • Glass lens
1.0
1
• Smooth ferrule
32.2
2X ø 2.2
stainless steel
Features
Free Cut*
Typical Range (mm)
ø 5.1
polyethylene
2000
17.0 stainless steel
2X ø 2.2 polyethylene
ø 5.1
2X ø 2.2 polyethylene
ø 3.0
stainless steel (non-bendable) probe
2X ø 2.2
ø 5.1
stainless steel
1
3.0
100
150
200
250
50
100
150
200
250
1
20
40
60
80
100
• Smooth ferrule; non-bendable tip
M3 x 0.5 nickel plated brass
polyethylene
0.5
1
• Thread 10
11.0
2000 2X ø 2.2
M6 x 0.75 nickel plated brass
polyethylene
20
30
40
50
60
ø 4.0
1.0 2000
14.0
3X M3 x 0.5
50
• Thread; bendable tip
51
14.0
2X ø 1.0
250
3.2
ø 3.0
1.0
2000
200
• Smooth ferrule
89.0
17.0
polyethylene
150
annealed stainless steel (bendable) probe
1.0 2000
1
17.0
14.0 M6 x 0.75 nickel plated brass
100
ø 3.05
1.0 2000
50
1
• Thread 50
3.0
100
150
200
250
aluminum
2X ø 2.2
polyethylene
15.0
20.0
13.0 2000
10.85
32X 0.265 32X ø 0.265
20.0
20.0 32X ø 0.265 13.0
2000
15.0
polyethylene
50
100
150
200
250
300
50
100
150
200
250
300
5.0
20.0
aluminum
• Rectangular tip
5.0
10.85
3X M3 x 0.5
25
2X ø 2.2
32X 0.265
25
• Rectangular tip; side sensing
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Model Number
Drawing & Dimensions (mm)
P22-C1
plastic
P12-C1
12
3 0.50
2000 14.2
plastic
0.5
19.0
7.0
12
3 0.50
Polyethylene
2000
7.0
countersink ø3.6deep Stainless ø 4.6ø 6.0Shrink Junction Braid Over Monocoil
P32-C6
2000 ø2.9 Stainless ø3.6 Stainless Braid Over 14.0 Braid Over Monocoil Monocoil 191
Shrink 30.0 Junction
ø 4.6
ø 2.2
2.4
ø 5.1 25.4
30.0
ø 3.0 R 12.7 M6 x 0.75 stainless steel ø 4.0
Indicators Safety Light Screens Safety Laser Scanners
1.0
25
16.5
Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules
• Flat mount; 6 mm range; lensed convergent optics
Safety Interlock Switches Emergency Stop Devices
14.0
16.5
R 12.7
1.0
ø 5.1 M6 x 0.75 stainless steel ø 4.0
191
• Side exit with lenses; 3 mm range; DURA-BEND fiber
3.0 ø 3.0
stainless steel
ø2.9 Stainless Braid Over Monocoil
25.4
stainless 19.65 steel
1000 15.5
14.0
13.0
Plastic 15.5
• Straight exit with lenses; 3 mm range; DURA-BEND fiber
polyethylene
2X ø 3.2
2x ø 1.3 ø 2.2
Vision
5.0
8.4
2X ø 1.0
PBAT43TMB5
0.5 19.0
2X ø 3.4 ø 6 countersink
Typical Range (mm)
Wireless
5.0
8.4
2X ø 1.0
polyethylene
Features
Measurement & Inspection Sensors
Free Cut*
14.2
2X ø 3.4 ø 6 countersink
Mechanical Convergent
Core Dia. Min. Bend Radius (mm) (mm)
12
• 90° angle/thread 50
14.0
100
150
200
250
3.0
1000
FIBER SENSORS
PBT43TMB5 PBPS43TMB5 PBF43TMB5
STEELSKIN
™
PBCT23TMB5M4
Diffuse
PBCT23TMB5
PLASTIC FIBERS ø 4.6
ø 2.2
Shrink Junction
15.5 30.0
191
ø 4.6
ø 2.2
ø 4.6
ø 2.2
30.0 191
ø3.6 Stainless Braid Over Monocoil
M4 x 0.7 stainless steel
ø 4.4
18.2
12
0.5 9X 0.25
12
ø3.6 Stainless Braid stainless Over Monocoil steel
ø 4.6
Shrink Junction
15.5
1.0
17.0
ø 4.6
ø 2.2
ø3.6 Stainless Braid Over Monocoil
ø2.9 Stainless Braid Over Monocoil 191 1000
30.0
Shrink Junction
15.5 30.0
191
ø 2.2
ø 4.6
15.5
12
stainless steel (non-bendable) probe
ø 5.1
1.0
ø 3.0
stainless steel 14.0
60
80
100
120
140
160
180
20
40
60
80
100
120
140
160
180
• Smooth ferrule
12
50
100
150
200
250
20
40
60
80
100
50
100
150
200
250
50
100
150
200
250
• Smooth ferrule; non-bendable tip
51
ø3.6 Stainless Braid Over Monocoil
M6 x 0.75
2.0
ø2.9 Stainless Braid Over Monocoil
ø 4.0
1.0
12
• Thread
17.0
1000
17.0
25.4
Shrink Junction
M6 x 0.75 stainless steel
ø2.9 Stainless Braid Over Monocoil
30.0
40
ø 5.1
1000
ø 2.2
20
• Thread
24.0
ø2.9 Stainless Braid Over Monocoil
ø3.6 Stainless Braid Over Monocoil
PBTA43TMB5
0.5 9X 0.25
1000
Shrink Junction
15.5
GLASS FIBERS
• Miniature thread
18.4
ø2.9 Stainless Braid Over Monocoil 191 1000
30.0
M3 x 0.5 stainless steel
ø 4.4
13.2
ø2.9 Stainless Braid Over Monocoil
Shrink Junction
15.5
ø3.6 Stainless Braid Over Monocoil
1.0
ø 3.0 R 12.7
12
• Thread/90° angle
25.4
stainless steel
191
More on next page
1000
NA: WORLD-BEAM QS18 not recommended.
Indicates lens available for model. See page 247 for details.
* Fibers can be free cut using fiber cutter (see page 255).
PLASTIC FIBERS
PDI46U-LLD TGR3/8MPFMQ PBT26UM6M.1 PBE46UTMLLPHT1 PBE46UTMLLP PBT46UHT1 PBTP43TMB5 PBRS26U PBE46UTMNL
Liquid Level
ø 4.6
ø 2.2
15.5
Shrink Junction
17.0
2X ø 2.2
1.0
ø 3.0
M6 x 0.75 stainless steel
2000
14.0
12
16.5
25
25
1.0
25
• Fluoropolymer encapsulated; withstands 105° C • Sensor switches when tip of fiber is immersed in liquid
0.5
12
0.5
12
ø 6.0
1830 2000
75 Do not bend this area
16.5
polyethylene
6.0
ø 6.0
1830 2000
2000
3.0
14.0
31.6
M6 x 0.75 o-ring
7.6
ø 3.0
quartz glass rod 15.7
A
A
6.4
12.7
90
3.0
3/8 - 32 polypropylene 2 nylon jam nuts
5.1
7.3
1.0
1
0.5
12
• 3.2 mm thickness; DURA-BEND fiber
plastic
4.2
9.0
2000 7.5
2X ø 0.5 fibers 1.6
50
100
150
200
250
Outer: 2X ø 4.4 Inner: 2X ø 3.2 9.0
2X ø 2.2
250
• Quartz probe; polypropylene housing • Sensor switches when tip of quartz is immersed in liquid
• Clear tube mount; DURA-BEND fiber • Sensor switches when liquid meniscus reaches optical axis
15.2
ø 2.2
20
plastic 2000
200
A — - — A CROSS-SECTION DETAIL
polyethylene
2X ø 1.0
150
stainless steel collar
11.4
20
polyethylene
100
ø 4.0
M6 x 0.75 nickel plated brass
2X ø 2.2
50
• Thread; withstands 105° C
• Fluoropolymer encapsulated • Sensor switches when tip of fiber is immersed in liquid
6.0
1.0
polyethylene
ø 5.7 FEP †Teflon®
• Thread; bendable tip
3.0
75 Do not bend this area
ø 5.7 FEP †Teflon®
polyethylene
Typical Range (mm)
ø 4.0
1.0
2X ø 2.2
Free Cut*
89
M6 x 0.75 nickel plated brass
polyethylene
2X ø 2.2
Features
ø3.6 Stainless Braid Over Monocoil
ø2.9 Stainless Braid Over Monocoil 191 1000
30.0
GLASS FIBERS
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
Flat Pack
Diffuse
High-Temp
STEELSKIN™
Model Number
Chemical Resistant
SENSORS
FIBER SENSORS
25.0
5.0
20
30
40
50
60
18.0
ø 5.7 † ® FEP Teflon
polyethylene
ø 6.0 1830 2000
10
3.2
1.0
25
• Fluoropolymer encapsulated tip 50
100
150
200
250
NA: WORLD-BEAM QS18 not recommended. NA: D10–Discrete not recommended. * Fibers can be free cut using fiber cutter (see page 255).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
300
350
400
More on next page
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Model Number
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
Features
Measurement & Inspection Sensors
Free Cut*
Typical Range (mm)
Vision Wireless
ø 6.0
ref. model PBCT26U
lens optic 11.0
9.2
ref. model PBCT26U
20.2
L4C20
ø 6.0
ref. model PBCT26U
lens optic 9.0
4.7
ref. model PBCT26U
13.7
8.6
ø 4.5 glass lens
2X ø 3.1
15.5
6.0
black anodized aluminum
ref. model PBT26UM3
12.5
2.0
M3 x 0.5 thread
• Anodized AL housing; ø 0.25 mm beam spot @ 6 mm • Fixed focus
Indicators Safety Light Screens Safety Laser Scanners
ø 4.0
LZ3C8
Convergent Spot Lens
Dif f use
L4C6
ø 4.0
ref. model PBCT26UM3
5.4
Fiber Optic Safety Systems
• Anodized AL housing; ø 4 mm beam spot @ 20 mm • Fixed focus
Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches
• Anodized AL housing; ø 0.5 - 3.2 mm adj. beam spot • Adjustable focus
Emergency Stop Devices
FIBER SENSORS PLASTIC FIBERS GLASS FIBERS
PIA16U
Model Number
ø 1.42
ø 1.0
polyethylene
PIA26U
4.8
R 3.5
7.6
Free Cut*
Typical Range (mm)
8
• 90° angle 5
10
15
20
25
30
35
40
160
180
ø 0.91
polyethylene 4.8
R 3.5 polyethylene
ø 1.0
25
ø 1.47
stainless steel
PIAT16U
polyethylene
ø 1.0 ø 1.47
stainless steel ø 1.0
R 5.1
M3 x 0.5 nickel plated brass
2000
stainless steel
PIAT26U
2000
ø 1.0
ø 2.2
13.9 ø 1.47
2000
stainless steel 2000
polyethylene 2000
ø 1.47
ø 3.3 13.9
M3 x 0.5 nickel plated 25.4 brass
R 5.1
ø 1.47
polyethylene
stainless steel ø 1.47
R 12.7
M4 x 0.7 stainless steel M2.5 x 0.45
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
40
60
80
100
120
140
11.0
0.25
8
• 90° angle/thread 20
9.6
40
60
80
100
11.0
0.5
12
• 90° angle/thread
11.0 50 R 12.7
M2.5 x 0.45 ø 3.3
• 90° angle 20
9.6
M3 x 0.5 nickel plated brass stainless steel 25.4
R 5.1
M4 x 0.7 stainless steel ø 2.2
12
9.6
25.4 11.0
25.4
polyethylene
R 5.1
M3 x 0.5 nickel plated brass 9.6
25.4 2000
polyethylene
0.5
25.4
2000
PIAT46U
0.25
25
ø 1.0
Standard
Features
ø 0.91
2000
Oppos e d
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
16.5
100
150
200
250
300
16.5
10.9 3.0
1.0
25
• 90° angle/thread
10.9
200
400
600
800
1000
3.0
Indicates lens available for model. See page 253 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
PLASTIC FIBERS
PIAT46UM.4X.4MT
Model Number
2000
12.7
ø 2.2
stainless steel
2000
ø 3.2
polyethylene
ø 2.2 2000
PIAT66U
R 7.9 ø 4.0
M2.5 x 0.45
ø 1.47
PIF16U
ø 1.0
PIF26U PIF26UMLS
• 90° angle/thread; long range
8
12
ø 3.0
12
15.0
1500
2000
20
30
40
50
60
70
80
90
• Smooth ferrule
• Smooth ferrule; thick jacket (ø 2.2 mm)
50
100
150
200
250
300
350
400
50
100
150
200
250
300
350
400
ø 3.18
stainless steel
25
• Smooth ferrule 200
17.0 ø 2.2
1000
• Smooth ferrule 10
1.0
stainless steel
1.5 2000
400
600
800
1000
1200
ø 3.18
PIF66U
polyethylene
38
500
0.5
polyethylene
1000
ø 2.2
stainless steel
2000
38
• Smooth ferrule; long range 500
15.0
ø 2.2
PIFM46U
1.5
17.0
ø 2.2
1000
1500
2000
2500
ø 3.0 stainless steel
polyethylene
1.0 2000
25
• Smooth ferrule; miniature tip
15.0 plastic
ø 2.2
PIL46U
3.0
0.5
2000
800
ø 2.0
stainless steel
ø 2.2
600
10.9
15.0
ø 1.0
400
16.5
0.25
polyethylene
• 90° angle/thread
3.0
stainless steel
2000
M8 x 1 acrylic lens
plastic
ø 10.8
polyethylene
1.0 2000
7.6
ø 1.0
PIT16U
25
10.9
2000
polyethylene
Typical Range (mm)
200
R 19.1
stainless steel
polyethylene
10.
25.4
M2.5 x 0.45
PIF46U
R 12.7
M4 x 0.7 stainless steel ø 3.3
Free Cut*
3.0
ø 1.47
M4 x 0.7 stainless steel
Standard
10.1 25.4 5.1
M2.5 x 0.045 stainless steel stainless ø 3.3 25.4 steel
13.9
Features
10.1
13.9 ø 1.47
polyethylene ø 2.2
GLASS FIBERS
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
polyethylene
Opposed
SENSORS
FIBER SENSORS
polyethylene
19.1
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
400
600
800
1000
1200
2000
4000
6000
8000
10000
12000
M2.5 x 0.45 stainless steel
0.25 2000
25
12.7
• Plastic lens; ultra-long range • Lens available separately, see page 253.
200
8
• Thread
10.0
10
20
30
40
50
Indicates lens available for model. See page 253 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
60
70
80
90
More on next page
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Model Number
Drawing & Dimensions (mm)
PIT26U
ø 1.0
PIT46U
Standard
2000
11.0
PIT66U
ø 2.2
PIP16U
ø 1.0
PIP26U
Probe
PIP46U PLIS-1
14.0
PIPS26U PIPS46U
0.5
3.0
4.0
stainless steel (non-bendable) probe stainless steel
12
2.5
0.5
stainless steel (non-bendable) probe ø 1.47 ø 3.18
stainless steel
1.0
Safety Two-Hand Control Modules
1500
2000
2500
30
40
50
60
70
80
90
PLASTIC FIBERS GLASS FIBERS 100
150
200
250
300
350
400
200
400
600
800
1000
1200
250
500
750
1000
1250
1500
• Smooth ferrule; non-bendable tip 40
60
80
100
120
140
25
• Smooth ferrule; non-bendable tip 100
200
300
400
500
200
400
600
800
1000
100
200
300
400
500
3.0 2.5
annealed stainless steel (bendable) probe
1.5
38
• Smooth ferrule; non-bendable tip
2.5
ø 1.27
5.0
• Low beam divergence angle of 2° • Ideal for wafer mapping
51
15.0
15.0
• Thread; bendable tip
51
stainless steel (non-bendable) probe
ø 3.0
12
2.5
2.0
1.0 2000
Safety Controllers & Modules
3.0
14.0
2000
polyethylene
1000
20
20
stainless steel
stainless steel ø 3.0
1200
• Thread; bendable tip
51
ø 2.11
ø 2.2
1000
3.0 ø 0.91
14.0
2000
polyethylene
800
• Smooth ferrule; non-bendable tip
89
ø 1.0
ø 2.2
PIPS66U
25
31.4
polyethylene
600
Emergency Stop Devices
50
3.0
8.2
ø 2.2
400
FIBER SENSORS
12
ø 1.47
2000
PIPSB46U
8
89
ø 2.3 beam exit stainless steel
polyethylene
Safety Light Screens
annealed stainless steel (bendable) probe
2000
ø 1.0
400
• Thread; long range
10
1.0
ø 2.5
350
annealed stainless steel (bendable) probe
ø 0.91
M4 x 0.7 nickel plated brass
2000
38
25.4
11.0
ø 2.2
Side-View
0.25
0.5
polyethylene
300
Fiber Optic Safety Systems
500
stainless steel (non-bendable) probe
7.6
2000
250
• Thread
3.0
ø 0.91
M3 x 0.5 nickel plated brass
200
Safety Interlock Switches
ø 1.3
2000
150
M2.5 x 0.045
11.0
polyethylene
25
200
1.5 2000
100
Safety Laser Scanners
3.0
M4 x 0.7 nickel plated brass
polyethylene
Indicators
M2.5 x 0.045
1.0
ø 1.0
Vision
• Thread 50
M4 x 0.7 nickel plated brass
polyethylene
ø 1.0
12
11.0
2000
polyethylene
Typical Range (mm)
Wireless
0.5
polyethylene
Features
Measurement & Inspection Sensors
Free Cut*
M3 x 0.5 nickel plated brass
polyethylene
ø 2.2
Opposed
Core Dia. Min. Bend Radius (mm) (mm)
bendable area
65.0
10.2
25
• Smooth ferrule; bendable tip
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
PLASTIC FIBERS
PIPSM26U
ø 2.49
polyethylene
stainless steel
2000
0.5
12
ref. model PIT46U
ref. model PIT46U
• Compact glass prism • M2.5 thread
1.0
2
• Right angle; side exit; Delrin
8.0
2X ø 2.3
L2RA
ø 2.2
12.0
2000 2000 (79)
ø 2.2 (0.09)
Stainless Steel M4 X 0.7 Stainless steel jam nut and ITLW
PIFM1X46U
6.5 (0.26) 3.0 (0.12)
1.0
2000
PIT1X46U PIP46UC
M3 x 0.5 nickel plated brass
annealed stainless steel (bendable) probe ø 1.47
1.0
ø 23
2000 fully extended
280
polyethylene 2000
14.0
M4 x 0.7 nickel plated brass
13.9
25.4 M2.5 x 0.045
1.0 stainless steel 11.0 3.0 ø 1.47
ø 3.3
2000 fully extended polyethylene 2000
280 13.9
25.4
R 12.7
M4 x 0.7 stainless steel M2.5 x 0.45
ø 2.2
ø 3.3
polyethylene
stainless steel ø 1.47
80
100
120
140
25
• Best for repetitive flexing (1,000s of cycles)
• Best for repetitive flexing (1,000s of cycles) • For applications involving reciprocating motion
300
450
600
750
150
300
450
600
750
50
100
150
200
250
300
350
50
100
150
200
250
300
350
100
200
300
400
500
600
700
800
100
200
300
400
500
600
700
800
• For applications involving reciprocating motion
10.9 3.0
1.0
1
• 90° angle/thread 200
10.9
M2.5 x 0.45
150
• Right angle; threaded, stainless steel
16.5
16.5
R 12.7
M4 x 0.7 stainless steel
ø 2.2
25
89
ø 23 ø 2.2 200
8
10.0
2000
ø 2.2
8
10.0
4X 0.25
200
2
ø 1.5
4X 0.25
M4 x 0.7 nickel plated brass
60
7.0 (0.28)
3.0
stainless steel
polyethylene
polyethylene
PIF46UHF
ø 7.9 5.0 (0.31) (0.20)
6.5
M2.5 X 0.45
ø 2.2
PIT46UC
M4 X 0.7 Stainless steel jam nut and ITLW 7.0 ø 7.9 M2.5 X 0.45
5.0
polyethylene
PIAT46UHF
3.0
Stainless Steel
Polyethylene 2000
40
7.6
Plastic
Polyethylene
ø 2.2
Typical Range (mm)
20
ø 4.0
Polyethylene
Free Cut*
• Miniature smooth ferrule; non-bendable tip
15.0
15.0
8.0 ø 2.8 lens optic
Features
ø 0.82
ø 1.0
ø 1.0
High-Flex
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
ø 1.0
DURA-BEND™
GLASS FIBERS
2.5
PIAT46UHFMTA PIA46UHFMB8X12
Right-Angle
Side-View
Model Number
Opposed
SENSORS
FIBER SENSORS
400
600
800
1000
1200
3.0
stainless steel
ø 3.18
polyethylene
1.0 2000
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
1
• Smooth ferrule
17.0
200
400
600
Indicates lens available for model. See page 253 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
800
1000
More on next page
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
PIFM46UHF
Model Number
ø 2.2
2000
PIP46UHF PIPS46UHF PIPSB46UHF
DURA-BEND™
polyethylene
2000
ø 3.18
polyethylene
PIT26UHF PIT46UHF PIE46UT PIE66UTMNL PIES46UT
1.0
1
1.0
10.2
bendable area
1
1000
Safety Controllers & Modules
Safety Interlock Switches
50
100
150
200
250
300
350
400
450
50
100
150
200
250
300
350
400
450
1
Emergency Stop Devices
FIBER SENSORS
• Thread
PLASTIC FIBERS
11.0
50
2000
100
150
200
250
300
GLASS FIBERS
M2.5 x 0.045
M4 x 0.7 nickel plated brass
1.0 11.0
1
• Thread
3.0
200
400
600
800
1000
22.0
ø 4.0 † FEP Teflon®
L2 lens polyethylene
ø 5.0
1.0
25
1830
• Fluoropolymer encapsulated; lens 500
2000 ø 4.0 FEP† Teflon®
1000
1500
2000
2500
3000
18.0
polyethylene
1.5
ø 5.0
38
1830
• Fluoropolymer encapsulated; lens 200
2000
400
600
800
1000
1200
1400
22.0
ø 4.0 FEP† Teflon®
polyethylene
L2RA side-view prism
ø 5.0
1.0
25
1830 2000
PIR1X166U
800
M3 x 0.5 nickel plated brass
polyethylene
PIRS1X166U
600
• Smooth ferrule; bendable tip
65.0
2000
aluminum
400
2.5 2.0
15.0
Safety Light Screens
Fiber Optic Safety Systems
• Smooth ferrule; non-bendable tip
51
0.5
ø 2.2
1000
Safety Two-Hand Control Modules
2.5
ø 1.27
polyethylene
polyethylene
800
3.0
annealed stainless steel (bendable) probe
5.0
ø 2.2
600
• Thread; bendable tip 200
ø 1.0
2000
1
89
14.0
ø 2.2
Chemical Resistant
ø 1.47
2000 stainless steel ø 3.0
400
Safety Laser Scanners
stainless steel (non-bendable) probe ø 1.47
stainless steel
ø 1.0
Area Sensing (Array)
Indicators
annealed stainless steel (bendable) probe
14.0
ø 2.2
ø 2.2
Vision
• Smooth ferrule; miniature tip 200
1.0
ø 2.2
1
15.0
M4 x 0.7 nickel plated brass
ø 2.2
Typical Range (mm)
Wireless
1.0
polyethylene
Features
ø 3.0 stainless steel
polyethylene
ø 2.2
Opposed
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
Measurement & Inspection Sensors
Free Cut*
10.0 2.5
100
200
300
400
500
600
aluminum
3X M3 x 0.5
8.0
5.25
15.0
16X 0.265 16X ø 0.265
15.0
2000
• Fluoropolymer encapsulated; side-view prism
25
• Ultra-compact head; straight exit; 5.25 mm width
5.0
100
200
300
400
500
600
700
800
900
100
200
300
400
500
600
700
800
900
15.0
3X M3 x 0.5
ø 2.2
5.25
10.0 (0.39)
15.0
8.0 2.5 2000
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
16X ø 0.265 polyethylene
16X 0.265
25
• Ultra-compact head; side exit; 5.25 mm width
5.0
Indicates lens available for model. See page 253 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
PLASTIC FIBERS
PIRS1X166UM.4
Model Number
20.0
4.0 2X ø 3.175 ø 7.1 countersink both sides
PIRS1X166UMPM.75
25
Free Cut*
Typical Range (mm)
• Compact head; side exit; 10 mm width
2000
ø 2.2
100
200
300
400
500
600
700
800
900
100
200
300
400
500
600
700
800
900
19 (REF) 5.1
16X ø 0.265
1.25 plastic
2X ø 3.0
16X 0.265
ø 2.2
polyethylene
25
• Side exit; 19 mm width
19.0 2.5
R 1.5
25
6.3
38.0 16X ø 0.265
5.1 34 (REF) 2X ø 3.0
plastic
16X 0.265
ø 2.2
polyethylene
6.3
ø 2.2
M2.5 x 0.045
M4 x 0.7 nickel plated brass
PDIS16UM5
2000
11.0
Plastic
800
1000
2X ø 3.2
200
300
400
500
600
700
800
900
15.0
0.25
10
Easy mount “fork” head; 5 mm gap
20.0
0.25
10
Easy mount “fork” head; 10 mm gap
1.0
25
• Easy mount “fork” head; DURA-BEND fiber
1.0
25
• 90° angle; compact “fork” head; DURA-BEND fiber
5.0
40.7
20.0
7.0
2x ø 1.3
5.0 10.0 12.0 Plastic 31.7
2000
2X ø 3.5
2X ø 2.2
600
• Thread; withstands 105° C 100
5.0 10.0
18.0
400
7.0
29.0
2000
25
3.0
2X ø 3.2 2x ø 1.3
polyethylene
200
R 1.5
25
1.0
Polyethylene
• Side exit; 34 mm width
38.0
cross-linked polyethylene
Polyethylene
25
19.0
2.5
PDIS16UM10
PIT46UHT1
16X 0.265
16X ø .265
R 3.6 polyethylene
2.2
PDIS46UM12
10.0
20.0
2000
PIRS1X166UMPMAL
Area Sensing (Array) High-Temp
Features
4.2
2000
Slot
GLASS FIBERS
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
9.5
Opposed
7.0
24.0
plastic sensing beam ø 1.0 fibers
24.0
24.0
32.0
2000
5.0 7.0 6.2
PDISM46UM5MA
SENSORS
FIBER SENSORS
plastic 2X ø 3.2 3.6
6.4
2X ø 1.0 fibers
19.0
5.0
2X ø 2.2
4X R 1.6
2X 0.8 18.4
18.4
26.2 polyethylene
7.2
8.3
2000
NA: WORLD-BEAM QS18 not recommended. * Fibers can be free cut using fiber cutter (see page 255).
14.5
3.5
Indicates lens available for model. See page 253 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Model Number
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm)
Features
Measurement & Inspection Sensors
Free Cut*
Typical Range (mm)
Vision
PIAT43TMB5
1000
ø 4.6
ø 2.2
Wireless
ø2.9 Stainless Braid Over Monocoil
25.0 ø 4.0
ø 3.2
ø 1.5 stainless steel
PIPS43TMB5 PITA43TMB5
PIT43TMB5
S TEEL S KIN ™
PIF43TMB5
30.0
PITP43TMB5 PDIT26T5 PDIT4100U PIF66UM.52M.19D
ø 2.2
6.6
30.0
Safety Laser Scanners 200
12
ø 4.0 ø 3.2
15.5 30.0
21.3
12
51
1.0
3.0
30.0
14.0
ø 4.0
15.5
ø2.9 Stainless Braid Over Monocoil
30.0
12
6.6
25.4
1.0
400
450
400
600
800
1000
FIBER SENSORS
12
• Thread/90° angle
ø 1.9
14.0
1.0
12
600
800
1000
200
400
600
800
1000
• Thread; bendable tip
89.0
15.5
12
• Accomplish 2 inspections using only one sensor
2X 11.0
2000 M4 x 0.7 nickel plated brass
2X ø 2.2
400
2X M3 x 0.5 nickel plated brass
2X ø 1.0
polyethylene
200
annealed stainless steel (bendable) probe
0.5 30.0
350
GLASS FIBERS
R 12.7
20.6
ø 4.6 polyethylene
300
• Thread
stainless steel
M4 x 0.7 stainless steel
1000
ø 2.2
250
ø 1.47
20.6
ø 4.6
200
25.4
1000 ø 2.2
150
PLASTIC FIBERS
ø 4.0
ø2.9 Stainless Braid Over Monocoil
100
200
M4 x 0.7 stainless steel
15.5
Safety Interlock Switches
M2.5 x 0.45
22.0
ø 4.6
1000
• Smooth ferrule; non-bendable tip
1000 ø 2.2
800
M4 x 0.7
13.0 30.0
600
Emergency Stop Devices
1.0
ø 1.5
ø4.0
15.5
400
2.5
50
ø2.9 Stainless Braid Over Monocoil
ø 4.6
Fiber Optic Safety Systems
Safety Two-Hand Control Modules
3.2
1000
ø 2.2
1000
15.0
stainless steel (non-bendable) probe
stainless steel
800
• Smooth ferrule 200
ø2.9 Stainless Braid Over Monocoil
ø 4.6
600
Safety Controllers & Modules
1000
ø 2.2
400
ø 3.0
1.0
15.5
Safety Light Screens
• 90° angle/thread
3.0
ø 4.0
stainless steel
12
14.0
M2.5 x 0.45
ø2.9 Stainless Braid Over Monocoil
1.0
50
100
150
200
250
300
M2.5 x 0.045
11.0
3.0
• 30 m duplex fiber cable
1.0
25
1.5
38
ref. model PIT46U
ref. model PIT46U
• Range-extending lens • M2.5 thread
ref. model PIL46U
ref. model PIL46U
• Ultra-long rangeextending lens; use with raw plastic fiber
Contact factory for sensing range.
305
30480 ø 2.2
stainless steel
polyethylene
2000
ø 4.75
13.2
• For use with VFT-M8MVS (ambient side) See page 261.
Contact factory for sensing range.
L2
ø 4.0 ø 4.3
lens optic 9.2
nut
LO8FP
Dual Individual Vacuum Extended Range Lens
M4 x 0.7 stainless steel
22.9
ø 4.6
16.5
R 12.6
14.0
15.5
Opposed
Indicators
stainless steel
compression washer
M8 x 1 lens optic
compression gasket
mounting nuts
XX.X
NA: WORLD-BEAM QS18 not recommended. NA: MINI-BEAM Expert not recommended. * Fibers can be free cut using fiber cutter (see page 255).
Indicates lens available for model. See page 253 for details.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
PLASTIC FIBERS
BMT16.6S-HT IMT.756.6S-HT†
High-Temp High-Temp
Dif f use
Model Number
Opposed
SENSORS
FIBER SENSORS
Core Dia. Min. Bend Radius (mm) (mm)
Drawing & Dimensions (mm) ø 4.6
ø 2.2
PVC shrink junction ø 4.6
ø 2.2
15.5
15.5 30.0
PVC shrink junction
ø 3.0 30.0 150
øø2.2 4.6
ø 2.2
ø 4.2
øø 3.0 4.6
38
ø 3.0
150
2000
38
ø 4.2
GLASS FIBERS
M4 x 0.7 stainless steel
1.57
15.0
19
15.0
steel
2000
ø 3.0 stainless stainless ø 4.2 steel steel
1.27 30.0
12.0
30.0
2000
• High performance glass fiber optics for use with Banner D10 plastic fiber sensors • Miniature thread; end tip withstands 315° C
ø 4.2 M4 x 0.7M4 x 0.7 M2.5 M2.5 stainlessstainless steel steel x 0.045 x 0.045
15.5
15.5
12.0 3.0
Free Cut*
Typical Range (mm)
• High performance glass fiber optics for use with Banner D10 plastic fiber sensors • Miniature thread; end tip withstands 315° C
M4 x 0.7 stainless steel
stainless steel stainless
Features
19
3.0
2000
NA: WORLD-BEAM QS18 not recommended. NA: MINI-BEAM Expert not recommended. * Fibers can be free cut using fiber cutter (see page 255). † Fibers are sold separately, must order two fibers to form a pair.
100
200
200
400
300
600
800
400
1000
Indicates lens available for model. See page 253 for details.
D10 Expert™ Small Object Counter Fiber Optic Arrays Model Number* Fiber Exit
Drawing & Dimensions (mm) 83.0
PFCVA-10X25-S
25.0
1.5 mm
25 x 25 mm
3 mm
34 x 25 mm
4 mm
42.0
End Exit
75.0
4X ø 3.2 ø 6.5 countersink 3.0 deep
83.0
14.5
Side Exit 25.0
30.0
25.0
PFCVA-25X25-E
End Exit
PFCVA-34X25-S
Side Exit
75.0
42.0
25.0
End Exit
14.5
30.0
34.0
75.0
• D10DNCFP... • D10DPCFP...
4X ø 3.2 ø 6.5 countersink 3.0 deep
83.0
PFCVA-34X25-E
10 x 25 mm
Used With
14.5
10.0
PFCVA-25X25-S
Minimum Object Detection†
Side Exit 30.0
PFCVA-10X25-E
Detection Window
42.0
4X ø 3.2 ø 6.5 countersink 3.0 deep
* Custom fiber arrays and mounting configurations are possible. Contact factory with your small object counting application. † With 2% Threshold Offset Percentage
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Fiber Optic Accessories
Fiber Cutters
Model Number
PFK20
PFK40
Model Specific Features • For use with 0.25 and 0.5 mm diameter cables.
• For use with 1 and 1.5 mm diameter cables.
General Features
Drawings
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors
• These kits are used with unterminated plastic fiber cables. • Each kit contains 40 bushings and 10 cutter assemblies (cutters can be purchased separately in packages of 25 - reference model PFC-2-25).
Vision Wireless
NOTE: Bushings used with Q45, OMNI-BEAM, ECONO-BEAM, MAXI-BEAM and VALU-BEAM sensors only.
Indicators Safety Light Screens Safety Laser Scanners
Plastic Fiber Field-Installable Sheathing
PFS69S6T
PFS53S6T
• May be used with individual or bifurcated fiber assemblies having M4 x 0.7 threaded end tips (e.g., PBCT26U, PBPF26U, PIP46U, PIT46U and PIT66U).
PFS44S6T
• May be used with individual fiber assemblies having M3 x 0.5 threaded end tips (e.g., PIP26U, PIT26U and PIT1X46U).
Plastic Fiber Adapters
• May be used with bifurcated fiber assemblies having M6 x 0.75 threaded end tips (e.g., PBCT46U, PBP46U, PBT46UHT1 and PBT66U).
UPFA-1-100
• Use to adapt plastic fiber optic cables with outside jacket diameter of 1.0 mm, such as PIT26U and PBP16U.
UPFA-2-100
Model Number
• Use to adapt plastic fiber optic cables with outside jacket diameter of 1.25 mm or 1.3 mm, such as PBCT26U and PBF46UM3MJ1.3.
Core
PIU230U
Fiber Optic Safety Systems
• Compression fitting adapters are used with small-diameter unterminated plastic fiber cables. • Use when interfacing small-diameter plastic fibers to D10, D11, D12, QM42, QS18, R55F, FI22 and MINI-BEAM plastic fiber sensor families. • Each kit contains 100 pairs of adapters. One pair will interface either one bifurcated fiber optic cable or a pair of individual cables to a fiber optic amplifier.
Length
Unterminated Individual and Bifurcated Plastic Fibers
Type
Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
FIBER SENSORS
Fiber end
PIU260U
Adapter
Drawing
Single 18 m
PIU430U
9m 1.0 mm
PIU460U
Single 18 m
PIU630U
9m 1.5 mm
PIU660U
Single 18 m
PBU430U
9m 1.0 mm
PLASTIC FIBERS GLASS FIBERS
9m 0.5 mm
PBU460U
Safety Controllers & Modules
• Stainless steel sheathing with stainless steel end fittings (one end internally threaded to capture fiber end tips, other end non-threaded) is used in applications where protection is required for plastic fiber optic cables. • All models listed are 1.8 m in length. • Other lengths are available by contacting Banner Applications Department.
Duplex 18 m
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS
PLASTIC FIBERS
GLASS FIBERS
SENSORS
Glass Fiber Optics • Solve numerous challenging sensing applications in the most hostile environments, including temperatures up to 480° C, corrosive materials and extreme moisture • Withstand severe shock and vibration • Ignore extreme electrical noise • Constructed of a combination of optical glass fiber, stainless steel, PVC, brass, molded thermoplastics and optical-grade epoxy
Glass Fiber Optic Model Key I
A T 2 3 S X X
ASSEMBLY STYLE designator
MODIFICATIONS designator
B = Bifurcated fiber I = Individual fiber*
“MXX” = Sensing end tip modification “M600” = Sensing end withstands 315° C “M900” = Sensing end withstands 480° C SHEATHING MATERIAL designator
SENSING END TIP STYLE designator A = 90° Angle AM = Miniature 90° Angle AT = 90° Angle/Thread F = Ferrule M = Miniature Tip MP = Miniature Probe MT = Miniature Thread R = Rectangular Bundle Termination T = Thread TA = Thread/90° Angle TETA = Thread and Extra Tight 90° Angle
* Individual glass fibers are packaged separately.
S = Stainless steel flexible conduit P = PVC with galvanized monocoil reinforcing wire OVERALL LENGTH designator (in feet) 2 = 2 ft. = 610 mm ±38 mm 3 = 3 ft. = 914 mm ±38 mm
FIBER BUNDLE DIAMETER designator .44 = 0.7 mm .5 = 0.8 mm .75 = 1.2 mm 1 = 1.6 mm 1.5 = 2.3 mm 2 = 3.2 mm 2.5 = 4.0 mm
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
Construction
Combination of optical glass fiber, stainless steel or PVC, brass, molded thermoplastics, and optical-grade epoxy. Optical fiber is F2 core, EN1 clad, approx. 50 µm diameter per strand. Flexible steel interlock sheathing is 302 stainless.
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Sensing Range
Refer to the specific fiber optic to be used.
Measurement & Inspection Sensors
Bend Radius
Inside bend radius must be 12 mm or greater for PVC covered fiber optic assemblies, and 25 mm or greater for stainless steel armored cable covered fibers.
Vision
Length
Standard length for assemblies is 915 mm; see dimension diagrams. Most models are available from the factory with shorter or longer cable lengths, up to 18 m max.
Length Dimension Tolerance
Overall assembly length: ±12 mm per 300 mm of length Shrink junction dimensions: ±12 mm
Glass Fiber Optics Specifications
Implied Dimensional Tolerances All dimensions are in millimeters: x = ±2.5 mm, x.x = ±0.25 mm and x.xx = ±0.12 mm, unless specified. Operating Conditions
Fiber assemblies with stainless-steel (SS) sheathing and metal end tips: -140° to +249° C Fiber assemblies with PVC sheathing and/or plastic end tips: -40° to +105° C Special order assemblies with SS sheathing and metal end tips and model suffix “M600”: -140° to +315° C* Special order assemblies with SS sheathing and metal end tips and model suffix “M900”: -140° to +480° C*; note dimensional changes from STD models
Wireless Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
* sensing end tip only
FIBER SENSORS PLASTIC FIBERS GLASS FIBERS
! Application Notes and Warnings ! 1
The ends of glass fiber optic assemblies are optically ground and polished. Care taken in this manufacturing process accounts for the light coupling efficiency of the fiber optic assembly. As a result, glass fiber assemblies cannot be shortened, spliced or otherwise modified.
2
Use caution when applying fiber optics in hazardous locations. Although fiber optic assemblies are by themselves, intrinsically safe, the sensor and associated electronics must be LOCATED IN A SAFE ENVIRONMENT. Alternatively, fiber optics may be used with sensor model SMI912FQD (page 43). This sensor is approved for use inside hazardous areas when used with an appropriate intrinsic barrier. Also, see NAMUR sensor models Q45AD9F (page 196) and MIAD9F (page 116). Fiber optics do not necessarily provide a hermetic seal between a hazardous environment and the safe environment.
3
In applications where glass fibers to insulate the control from high voltage, specify silicone rubber, Teflon®, or high-density polyethylene sheathing with no reinforcing wire in the cable. It is the responsibility of the user to test each fiber optic assembly for insulation capacity.
4
Do not subject the fibers to sharp bends, pinching, repeated flexing or high levels of radiation.
5
When ordering fiber lengths in excess of 1 m, take into account light signal reduction of 5 percent per 300 mm of additional length. Teflon® is a registered trademark of Dupont™.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS
GLASS FIBERS
PLASTIC FIBERS
ST AT IC
Indicates lenses available for model. See page 259 for details.
SE
–
DO
P
TU LO DY NA MI C
t in Po
OF De F lay
h itc Sw
+
SME312
Model Number
D12E
QS18M600
D12
Drawing & Dimensions (mm)
AvailableM900 315° C models. Add M600 to end of model number (example, BA23SM600).
M900
Available 480° C models. Add M900 to end of model number (example, BA23SM900). Dimensions may vary for these models.
Core Dia. (mm)
Min. Bend Radius (mm)
3.18
19
Features
Typical Range (mm)
914 ø 7.4
PVC shrink junction
12.7
12.7
BAT23S
ø 4.7
ø 7.4
12.7
stainless steel
38.1
191
PVC shrink junction
12.7
12.7
ø 6.4
BA23S
ø 4.7
20.3
ø 4.8
BF23P
Standard
PVC shrink junction
ø 5.8
50
100
150
200
50
100
150
200
19 M600
ø 7.4
ø 4.8
12.7
PVC with monocoil
38.1
191
200
M900
5/16-24 UNF brass 2 brass jam nuts included
ø 3.18
3.18 12.7
150
• 90° angle/thread
914
12.7
100
R 12.7
3.18
ø 7.4
50
20.3
ø 4.8
191
ø 4.7
M900
27.9
ø 7.4
stainless steel
• 90° angle M600
R 12.7
12.7
ø 6.4
38.1
27.9
38.1
19
• Smooth ferrule
12.7
914
BMT.442P
ø 7.4
ø 4.7
PVC shrink junction
38.1 12.7
#8-32 thd brass 2 jam nuts included
ø 3.8
ø 3.0
12.7
PVC with monocoil
16.5 191
0.69
12.7
9.5
•M iniature thread
NA 2
4
6
8
10
610 ø 7.4
BT23S
ø 4.7
Diffuse
12.7
12.7
ø 8.0
ø 6.4
PVC shrink junction
5/16-24 thd brass 2 jam nuts included
stainless steel
38.1
12.7
ø 3.18
• Thread 3.18
38.1
19 M600
191 914
BTA23S
12.7
PVC shrink junction
ø 7.4
ø 4.7
12.7
12.7
ø 6.4
38.1
stainless ø 8.0 steel
191
38.1
M900
50
100
150
200
50
100
150
200
15.8
5/16-24 thd brass 2 jam nuts included
R 9.7
27.9
3.18
19
• Thread/90° angle M600 M900
ø 4.8
914 ø 7.4
12.7
PVC shrink junction
12.7
ø 8.0
ø 6.4
ø 1.5
stainless steel
38.1
4.8
1.17
R 3.05 35.6
191
19
25.4
ø 7.4
BM.752S
ø 4.7
12.7
PVC shrink junction
12.7
ø 7.4
ø 6.4
ø 4.6
38.1
1.17 12.7
12.7
NA
M900
19
25.4
NA • ø 1.5 mm non-bendable probe M600 M900
610 ø 7.4
ø 4.7
PVC shrink junction
ø 3.0 12.7
1.17
25.4
9.5
• ø 1.5 mm non-bendable probe
191 914
BR2.53S
ø 7.4
PVC shrink junction
38.1
25.4
12.7
12.7
191
38.1
50.8
12.7
stainless steel
6.4
38.1
ø 7.4
BR23S
PVC shrink junction
ø 6.4
2.54
12.7
12.7
38.1
191 914
NA: WORLD-BEAM QS18 not recommended.
2x 3.2
19.1
19
6.3 11.7
stainless steel
3.96
0.25
914
ø 4.7
40
50
10
20
30
40
50
10
20
30
40
50
50
100
150
200
250
NA
9.4
2x 4.8
ø 6.4
30
ø 1.5
ø 3.8
16.5
ø 4.7
20
PVC with monocoil
38.1 12.7
10
ø 1.5
stainless steel
191
• ø 1.5 mm non-bendable probe; 90° angle M600
610
BMP.753P
Miniature Probe
BAM.752S
ø 4.7
Area Sensing (Array)
SENSORS
R55F
M600
9.7
19.1 0.8
3.18
19
• Straight exit; 38 mm width M600
M900
• Straight exit; 10 mm width M600 M900
50
100
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
150
200
More on next page
ST AT IC
SE
–
DO
P
TU LO DY NA MI C
t in Po
OF De F lay
h itc Sw
+
R55F
SME312
Model Number
D12E
QS18M600
D12
Core Dia.
Drawing & Dimensions (mm)
(mm)
M600
AvailableM900 315° C models. Add M600 to end of model number (example, BA23SM600).
M900
Available 480° C models. Add M900 to end of model number (example, BA23SM900). Dimensions may vary for these models.
Min. Bend Radius (mm)
Features
Typical Range (mm)
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision
PVC shrink junction
ø 5.3
ø 5.1
Indicators
ø 3.05 ø 4.8
2.29 12.7
12.7
stainless steel
38.1
12.7
19
25.4
• Ultra-compact head M600 M900
Safety Light Screens 25
50
75
100
125
150
191
BA1.53SMTA BMT13SMVF
ø 7.4
ø 4.7
12.7
PVC shrink junction
12.7
stainless steel
38.1
ø 7.4
12.7
ø 6.4
PVC shrink junction
12.7
stainless steel
38.1 191
ø 4.7
ø 8.0
12.7
ø 4.8
5.3
• Compact head M600 M900 25
ø 3.05
25.4
38.1
19
ø 2.29 (0.09)
35.1
5/16-24 thd brass 2 jam nuts included
2.29
19
†
®
Teflon shrink junction
stainless steel
ø 4.2
M600
ø 3.0 ø 3.0
29.0
M4 x 0.7 stainless steel
15.0
1.57
19
150
50
75
100
125
150
Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop Devices
• Ultra-compact head; thread M900
914
ø 4.0
Safety Controllers & Modules
ø 3.05
ø 6.4
ø 5.3
191
ø 4.7
Safety Laser Scanners Fiber Optic Safety Systems
2.29
• Miniature thread; entire cable withstands 480° C
25
50
75
100
125
150
Contact factory for sensing range.
914
FIBER SENSORS PLASTIC FIBERS GLASS FIBERS
lens optic
L10
Vacuum
Diffuse Convergent Beam Spot
ø 7.4
ø 4.7
914
BTETA1.53S
Side-View
BA1.53SMETA
Wireless 914
ø 14.3 45.7
5/16" - 24 thread
ref. glass fiber key or call factory
ref. glass fiber key or call factory
• Glass lens; withstands 315° C • Focuses light to .80 mm with ø 1.6 mm fiber
Glass Fiber Optics—Additional Models Available
s Model e r o M ilable! Ava
In addition to the configurations shown, Banner offers thousands of readily available alternative fiber models: • Substitute PVC over monocoil sheathing for stainless steel. • Reduce or increase glass fiber optic bundle diameters. Example: Change ø 3.18 mm bundle to ø 1.57 mm. • Substitute a rectangular-shaped fiber bundle (0.5 x 2.5 mm) for a circular bundle. • Change endtip material from brass to stainless steel.
• Modify straight or angled probe tip dimensions. • Modify overall fiber length in intervals of 305 mm (standard lengths are 914 and 610 mm).
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
FIBER SENSORS
GLASS FIBERS
PLASTIC FIBERS
ST AT IC
Indicates lenses available for model. See page 261 for details.
SE
–
DO
P
TU LO DY NA MI C
t in Po
OF De F lay
h itc Sw
+
SME312
Model Number
D12E
QS18M600
D12
Drawing & Dimensions (mm)
AvailableM900 315° C models. Add M600 to end of model number (example, BA23SM600).
M900
Available 480° C models. Add M900 to end of model number (example, BA23SM900). Dimensions may vary for these models.
Core Dia. (mm)
Min. Bend Radius (mm)
3.18
19
Features
Typical Range (mm)
914 ø 7.4
IA23S
ø 4.7
12.7
12.7
ø 6.4
stainless steel
12.7
27.9
20.3
ø 4.87
• 90° angle M600
M900
R 12.7
200
400
600
800
1000
1200
200
400
600
800
1000
1200
200
400
600
800
1000
1200
20
40
60
80
100
120
200
400
600
800
1000
1200
200
400
600
800
1000
1200
914 ø 6.4
ø 7.4
ø 4.7
12.7
ø 4.8
• 90° angle/thread 3.18
5/16-24 UNF brass 2 brass jam nuts included
ø 4.7
IF23P
20.3 R 12.7
ø 7.4
M600
38.1
12.7
12.7
19
12.7
IMT.442P
914 ø 3.0
PVC with monocoil
ø 4.7
ø 7.4
• Smooth ferrule M600 M900
#8-32 thd brass 2 jam nuts included
ø 3.8
NA
0.69 12.7
M900
PVC with monocoil
3.18 12.7
19
ø 4.8
ø 7.4
ø 5.8
Standard
27.9
ø 7.4
stainless steel
12.7
IAT23S
12.7
12.7
16.5
9.5
• Miniature thread
12.7
914 ø 7.4
IT23S
ø 4.7
Opposed
5/16-24 thd brass 2 jam nuts included
ø 8.0
ø 6.4
ø 3.18
• Thread 3.18
12.7
stainless steel
12.7
12.7
19
38.1
M600
914
M900
914 ø 6.4
ITA23S
ø 7.4
12.7
IAM.752S
38.1
15.8
ø 8.0
ø 7.4
ø 8.0
ø 6.4
3.18
R 9.7
5/16-24 thd brass 2 jam nuts included
19
27.9
ø 1.5 4.8
12.7
1.17
R 3.05
stainless steel
12.7
ø 7.4
IM.752S
ø 4.7
35.6
ø 7.4
ø 6.4
19
25.4
stainless steel
12.7
12.7
• ø 1.5 mm non-bendable probe; 90° angle M600 M900
50
100
150
200
50
100
150
200
50
100
150
200
ø 1.5
ø 4.6
1.17 12.7
• Thread/90° angle M600 M900
ø 4.8
610
12.7
19
25.4
NA • ø 1.5 mm non-bendable probe M600 M900
610 ø 3.0
IMP.753P
Miniature Probe
12.7
stainless steel
12.7
ø 4.7
ø 7.4
ø 4.7
12.7
ø 3.8
ø 1.5
PVC with monocoil 12.7
16.5
1.17
25.4
9.5
• ø 1.5 mm non-bendable probe
NA
914
ø 7.4
IR2.53S
ø 4.7
6.4
ø 6.4
38.1
9.4
38.1
25.4 12.7
stainless steel
12.7
12.7
2.54
12.7
19
stainless steel 914
2x 3.2
• Straight exit; 38 mm width M600 M900
200
400
600
800
1000
1200
200
400
600
800
1000
1200
6.3
11.7 12.7
3.69
0.25 ø 6.4
ø 7.4
ø 4.7
50.8
2x 4.8
914
IR23S
Area Sensing (Array)
SENSORS
R55F
M600
19.1
9.7
19.1 0.8
3.18
19
• Straight exit; 10 mm width M600 M900
NA: WORLD-BEAM QS18 not recommended.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]
More on next page
ST AT IC
SE
–
DO
P
TU LO DY NA MI C
t in Po
OF De F lay
h itc Sw
+
R55F
SME312
D12
QS18
Core Dia.
Drawing & Dimensions (mm) stainless steel
ø 5.1
ø 7.4
ø 5.3
(mm)
12.7
12.7
M600
AvailableM900 315° C models. Add M600 to end of model number (example, BA23SM600).
Min. Bend Radius (mm)
Features
Typical Range (mm)
Vision
ø 3.05
12.7
2.29
19
25.4
Indicators
• Ultra-compact head M600
M900
100
200
300
400
500
600
IA1.53SMTA
914
ø 5.3
7.1
2.29
19
35.1
Fiber Optic Safety Systems
• Compact head M600
M900
914
ø 7.4
ø 4.7
12.7
ø 6.4
ø 8.0
ø 4.8
12.7
100
200
300
400
500
600
25.4
38.1
2.29
19
• Ultra-compact head; thread M600 M900
Safety Interlock Switches 100
200
300
400
500
600
914
ø 3.0 ø 4.7
ø 4.0
stainless steel
M4 x 0.7 stainless steel
ø 4.2
10.0
29.0
12.0
M2.5 x 0.045
1.27
19
• Miniature thread; entire cable withstands 480° C
ref. model IT23S
ref. model IT23S
• Glass lens; withstands 315° C
3.0
Safety Controllers & Modules Safety Two-Hand Control Modules
ø 3.05
5.3
stainless steel
12.7
5/16-24 thd brass 2 jam nuts included
Safety Light Screens Safety Laser Scanners
ø 3.05
ø 6.4
stainless steel
Measurement & Inspection Sensors
Wireless
ø 4.8
5.3
IMT.753SMVF
Vacuum
ITETA1.53S
Side-View
IA1.53SMETA
Model Number
D12E
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors
Emergency Stop Devices
Contact factory for sensing range.
914
lens optic
L9
ø 14.3 45.7
5/16" - 24 thread
FIBER SENSORS PLASTIC FIBERS
L16F
58.4
ref. model IT23S
ref. model IT23S
• Plastic housing; withstands 105° C
ref. model IT23S
ref. model IT23S
• Aluminum housing; withstands 315° C
ref. model IT23S
19
• Stainless steel housing withstands 480° C
3.56
—
L16FAL
lens optic ø 28.6 5/16" - 24 thread
58.4
lens optic
L16FSS
Extended Range Lens
ø 28.6 5/16" - 24 thread
ø 28.6 5/16" - 24 thread
58.4
A
22.23
VFT-M8MVS
Vacuum Feed Through
M8 x 1.25 A
4.0 10.0
35.0
stainless steel electropolish finish
#4-40 SS set screw 9.53
4.0 12.7
ø 3.56 image conduit
• Seals to 1 x 10-9 torr; withstands 120° C
#4-40 SS set screw 4.75
4.75 Viton O-ring
A — - — A CROSS-SECTION DETAIL
5/16-24 brass internal thread
40.0
ø 9.7
ø 3.18 (±0.125) 12.7
TGR
Liquid Level
Opposed
GLASS FIBERS lens optic
glass rod
3.18 97.8 effective length
—
• Use with BT23S • Sensor switches when tip of glass rod is immersed in liquid
90°
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email:
[email protected]