Sheetmetal

Proudly Distributed By

SHEETMETAL

19652

26146

Front Fenders for Wide Glide and Softail Models Custom Fender for Wide Glide Front Ends

A bolt-on version that completely replaces the stock front fender on Dyna Wide Glide, Softail and 4-speed FXWG models from 80-06 (except Heritage Softail, Fat Boy and Springer Softail models). Styled with an added accent bead around its entire edge. These fenders include polished aluminum spacer blocks, and fit with 19" or 21" wheels only. 13183 6" wide��������������������������������������$139.99

Fenders for Narrow Glide Models

Original-style front fenders for FX, FXR, Sportster and Dyna Glide models from 73-03. Available in a stock replacement version or with the front tip cut back for a trimmer look. Both fenders are unpainted and include chrome brackets and the rivets necessary to install them. 19652 Fender (repl. OEMs 59007-73TB, 59111-74)��������������������������������������$61.99

A trim, tire-hugging fender with chrome brackets, ready-to-paint. A reproduction of the Original Equipment front fender on FXST, FXSTC and 4-speed FXWG models from 80-07 and Dyna Wide Glide models 80-05. 26146 Replaces OEM 59924-80������������$42.99 26350 Same as CC #26146 except with raw steel mounting bracket�� $39.99

Wide Glide Front Fender for 35mm Forks

Custom front fender for the 35mm front forks on FX, FXR and Sportster models from 73-E87. Unpainted, and complete with integral chrome-plated brackets. For use with 18", 19" or 21" wheels. 26163 Replaces OEM 59031-83������������$45.99

Narrow Front Fenders Springer Front Fender for Big Twins Custom Skirted Fender with Flip Based loosely on the skirted early K model front fender, this timeless classic has been updated to fit all 35mm and 39mm front forks from 73-13. 13196 Unpainted (5 3/4" wide) ��������$112.99

Accurate, faithful reproduction of the original fender. Complete with braces and fender edge ‘reveal’. Fits all Big Twins from 37-48. 26520 Replaces OEM 59000-36 (measures 7 1/2"-wide)����������������������������������$109.99

These replacement narrow front fenders fit FX, FXR, Sportster and Dyna Glide models from 73-99 with 35mm or 39mm front forks. Available chrome or unpainted with chrome brackets. For use with narrow 18", 19" and 21" rims. 240331 Chrome fender and bracket �������� $49.99 240383 Unpainted fender and bracket (replaces OEM 59031-83) ��������$31.99

Note: Fender should not be used on bikes equipped with highway bars.

Narrow Front Fender for FL Models Front Fender for Early ‘Touring’ Models

A precisely-crafted reproduction of the 54-84 4-speed ‘Dresser’ front fender with properly rolled edges and structural reinforcement. Will also fit Touring models from 80-13. 13193 Unpainted steel�������������������������������������������������������������������������������������������������������������������������� $109.99

SHEET.02

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Custom, unpainted steel narrow FXWG-style front fender for all 4-speed FL model forks from 49-84. Includes chrome mounting brackets, the fender profile is designed to clear 18", 19" and 21" tires. 26159 Unpainted (7 3/4"-wide) ����������$52.99

Please see Cautionary Information in back of catalog.

SHEETMETAL

Front Fenders for 4-Speed Models

Our replacement steel fenders fit all 4-speed FL models from 81-84, and have all of the correct holes and dimples for fender trim and tip lights. 240380 81-84 style (replaces OEM 59093-79) ��������������������������������������$99.99

Hooded Skull Fender Ornament

• Chrome with a satin black hood • Universal mount will fit most front fenders • Includes a rubber mounting gasket and hardware (requires drilling fender for installation) 621124 Hooded skull fender ornament, sold each �����������������������$27.99

Chrome Lower Fender Trim

A reproduction of the lower trim installed on FL models from 68-75, but completely chrome-plated without the black accents. Fits all FL, FLT, FLHT and FLHS models from 49-85. Comes complete with chrome mounting hardware. 26585 Replaces OEM 59233-68��������������������������������������������������������������$19.99

Skull Head Fender Trim

26589

Quality die-cast trim piece is contoured to match the front fender on FL, FLT, FLHT models 80-13 and many custom applications. Features a highly detailed skull head logo with gold trim and 12 volt illuminated eyes. 240078 Chrome with gold trim and illuminated eyes �����������������������$53.99

26588

240071

Vintage ‘V’ Style Fender Tips and Trim

Reproductions of the chrome front and rear fender tips and stainless steel trim pieces. The fender tips are die-cast in the ‘V’ design used as Original Equipment from 59-66. The front fender side trim and front fender lower edge trim are formed in stainless steel. Each part includes hardware, and fits all FL front fenders from 49-86 and all FL rear fenders from 58-86. 26586 Front fender trim set (includes CC #’s 26588 and 26595)��� $29.99 26588 Front fender tip ‘V’ design (indexed for side spears) as used from 59-66 (repl. OEM 59216-59) ������������������������������������������� $19.99 26595 Front fender side spear set as used from 57-73 (repl. OEMs 59205-57 and 59206-57)������������������������������������������������������������� $16.99 26589 Rear fender tip ‘V’ design as used from 59-66 (repl. OEM 59887-59)��������������������������������������������������������������������������������������� $19.99

Eagle Head Fender Ornament

This die-cast fender ornament is highly detailed and come with illuminated eyes. The illuminated version is internally lit with 2 independent 12V light bulbs which can be connected to the turn signals or running lights. Fits FL, FLT and FLHT models 80-13 and many custom applications. 240071 Illuminated eyes with gold accented beak�������������������$24.99 27824 Replacement bulb, 12V 2W (box of 10)�������������������������������$0.60

w w w.cu sto m c h ro m e.co m

SHEET.03

SHEETMETAL

Quickbob Rear Fender for FX Models

Hinged Rear Fenders for FL Swingarms

These two-piece hinged fenders fit all 4-speed Big Twin FL frames from 58-84. They also fit FX models if FL struts are used and can be adapted to FXWGs. A slight dent must be made in the front right lower corner of the fender to clear the FXE battery box. Unpainted steel. 13186 With no taillight mount (repl. OEM 59604-65A)����������������$109.99

Custom rear fender for an easy, affordable conversion to the Fat Bob look. Fits stock 4-speed FX frames and uses the stock width fender struts. Cannot be used as a replacement fender for FXWGs. Heavy-gauge metal for lasting service. 13188 Fits FX models from 73-85 (except FXWG, FXST)������������������$89.99

Custom Fat Bob Rear Fenders

Original style universal and custom application fenders. Available with left or right-hand chain cutaway without taillight mount. Fenders measure approx. 38"-long, 7"-wide and 5 1/2"-deep. Fenders are unpainted. Left Chain Cutaway Fits all Big Twin models and bikes with the chain on the left side. 13178 Without taillight mount ������������������������������������������������������������$74.99

One-Piece Rear Fenders for FL Models

Accurate reproductions of the one-piece rear fenders on 4-speed FL models from 80-84. One version is smooth with no taillight or turn signal mounts, and the other has the 73-98 taillight mount (but no turn signal mounts). Fender strut mounting holes are already drilled. 13189 With no taillight mount������������������������������������������������������������$114.99 13212 With 73-98 taillight mount but no indentations for the turn signal mounting bar������������������������������������������������������������������$119.99

Right Chain Cutaway Fits Sportster models in custom frames and bikes with the chain on the right side. 13179 Without taillight mount ������������������������������������������������������������$75.99

Fat Bob Fender and Taillight Kit for FXR Models

• Custom Fat Bob styling • 3-piece kit includes Fat Bob fender, Fat Bob taillight and deluxe taillight bracket • Features flush-mount taillight positioning • Bolts easily to all stock fender struts • Compatible with Original Equipment and CC sissy bar kits 13250 Fits all FXR models from 82-94������������������������������������������������$179.99

25933

25932

25931

Rear Fenders for FX Models

Detailed reproductions of the Original Equipment 4-speed FX rear fenders from 73-85. Available with or without mounting bracket for 73-98 taillight assembly. 25931 Original style with light mount ������������������������������������������������$69.99 25932 Original style without mount����������������������������������������������������$65.99 25933 Custom bobbed����������������������������������������������������������������������������$74.99 Note: Taillight, visor and license mounting bracket are not included and are shown for illustration purposes only.

SHEET.04

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Rear Fender for FXR Models

Stock replacement rear fender for FXR models from 82-99 (except FXRT models). Unpainted steel. 240425 Replaces OEM 59634-81A ��������$74.99

Please see Cautionary Information in back of catalog.

SHEETMETAL 13208

13209

Sport Bob Rear Fender Kits for Sportster Models

These exclusive fender kits include a new ABS plastic fender extension for the front of the fender, a Cateye taillight assembly with mounting bracket and the extra pop rivets necessary to reinstall your circuit breaker clips. They looks great when combined with the CC #25576 one-piece Sport Bob gas tanks found elsewhere in this catalog section. 13209 Fits Sportster models from 94-03������������������������������������������� $164.99 13208 Fits Sportster models from 82-93������������������������������������������� $135.99

Rigid Rear Fender

A replacement rear fender for rigid frame Big Twins from 49-57. Includes braces and has holes drilled for the seat clip. Rear section is not drilled to permit choice of taillamp. 26524 Replaces OEM 59612-41������������������������������������������������������ $149.99

Rigid Rear Fender for 45s

An accurate reproduction of the rigid rear fender. Perfect in every detail and comes complete with brackets ready to bolt on. 13191 Fits 37-46 45" Twins�������������������������������������������������������������������$164.99

Rigid Rear Fender for Big Twins

An accurate reproduction of the rigid rear fender used on 36-48 overhead valve Big Twins. Perfect in detail and complete with brackets ready to bolt-on. Unpainted. 13187 Replaces OEM 59604-39������������������������������������������������������ $169.99

w w w.cu sto m c h ro m e.co m

SHEET.05

SHEETMETAL

13530

13531

Wide Fenders for Rigid Frames

Custom flat fenders made of heavy-duty 14-gauge steel in wide widths to cover that really big rubber. 95073 7 1/2"-wide������������������������������������������������������������������������������������$29.99 95074 8 1/2"-wide������������������������������������������������������������������������������������$35.99 95075 9"-wide ������������������������������������������������������������������������������������������$38.99

12459

’OneTonHo’ and ’TwoTonHo’ Custom Rear Fenders 12457

Universal Steel Rear Fenders and Supports Fenders Available in 5" or 6" widths. Great for trailers too. 12457 5" wide��������������������������������������������������������������������������������������������$29.99 12459 6" wide��������������������������������������������������������������������������������������������$39.99

Designed specifically for wide rigid frames. Fenders feature internal wiring loom and a belt cutout. The ‘TwoTonHo’ has built-in fender supports pre-drilled for turn signals while the ‘OneTonHo’ has no supports. 13530 9"-wide ‘TwoTonHo’������������������������������������������������������������������$149.99 13531 9"-wide ‘OneTonHo’������������������������������������������������������������������$139.99 13526 8 1/2"-wide ‘OneTonHo’ ����������������������������������������������������������$139.99 13520 7 1/2"-wide ‘OneTonHo’ ����������������������������������������������������������$139.99 For Santee 200-Series Rigid Frames 08680 9"-wide custom ‘OneTonHo’����������������������������������������������������$149.99

Billet ‘Machine Gun’ Fender Struts by Vulcan Engineering

13377

Custom Rear Fenders for Santee Rigid Frames

Plain steel straps support the rear fender on your wide-tired Santeeframed chopper. For Santee 180-Series Rigid Frames 13377 8 1/2"-wide rear fender with plain steel strap supports ��$139.99 16955 8 1/2"-wide without support ��������������������������������������������������$149.99

Here is a cool set of fender struts to help you mount that rear fender on your latest project. They are CNC-Machined from billet aluminum and then chromeplated. Fender struts measure 10 5/8” from mounting holes center to center. 668254 Chrome Billet ‘Machine Gun’ Rigid Fender Struts, Sold as a pair ������� $129.99

For Santee 200-Series Rigid Frames 16956 9"-wide without support����������������������������������������������������������$149.99

SHEET.06

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL 26517

26518

Steel “Petcock Bungs” by Johnny’s Custom Shop

26522

Chrome Fender Strut Sets

Chrome rear fender struts for 4-speed Big Twin, Sportster and K models from 54-86. All sets are formed from high-grade steel and pre-drilled with the correct mounting holes before polishing and plating. Can be used to mount custom, reproduction or Original Equipment fenders. Note: Hardware is not included, but is available as listed below.

26517 26518 78315 78319 26522

Fit FX models from 72-85 – 2 holes (not countersunk)��������$79.99 Fit FL models from 58-84������������������������������������������������������������$79.99 Fit FL models from 58-84 (turn signal holes have been removed)����������������������������������������������������������������������������������������$70.99 Fit FXWG from 80-86 (turn signal holes have been removed)

����������������������������������������������������������������������������������������������������������$73.99

While you’re creating that out of sight one-off tank, don’t forget you need to get the gas to the engine, and that calls for a petcock mount. Most petcocks used in custom applications, and what we offer, have either 3/8” NPT or 1/4” NPT threads. These steel Petcock Bungs are offered to accept either thread size. They are 2” long, with 1/2” of either 3/8” NPT or 1/4” NPT internal thread for your petcock to screw into, then the remaining 1 1/2” bored out to .8200 inner bore to allow good gas flow. Can be used with custom oil tanks as well. Comes Raw. Position Petcock Bung where you want the petcock to mount, cut a hole in the tank, then weld ‘er in!. Sold Each. 632705 Petcock Bung. 2” long, 7/8” O.D. For 3/8 NPT Petcocks�$15.99 632706 Petcock Bung. 2” long, 7/8” O.D. For 1/4 NPT Petcocks$15.99 632252 1/4” NPT Petcock. No reserve. (see petcocks) �������������������$27.99 632253 1/4” NPT Petcock. With reserve. (see petcocks) ���������������$45.99 12726 Fits OEM and custom tanks thru 74 with internal 3/8" NPT connection (repl. OEM 62125-55B) �������������������������������������$15.99 12727 3/8” NPT Petcock w/90 degree outlet. With reserve. (see petcocks) �����������������������������������������������������������������������������������$15.99

Fit Sportster and K models from 54-78 (turn signal holes have been removed)������������������������������������������������������������������������������$79.99

Chrome Fender Struts for Sportster Models

Chrome-plated die-cast aluminum replacements for the Original Equipment parts. Fit 4-speed Sportster models from 82-89 (replaces OEMs 59950-81 and 59951-81). 78055 Fits 82-89 XL models. Sold in sets����������������������������������������������$84.99

Rigid Frame Fender Struts

These cool looking fender struts are made of chrome plated billet and measure 9 1/4” from mounting holes center-to-center (10” overall length). A great looking fender strut set at an affordable price! Made in USA by Motorway. Sold as pair. 632008 Rigid Frame Fender Struts������$139.99

Steel “Round Bungs” and “Round Nuts” by Johnny’s Custom Shop

These Round Nuts are CNC machined for use as Sissy Bar mounts, Fender mounts, Gas Tank mounts and a hundred other applications. Paint, Chrome or Powder-coat as desired. Every person putting a bike, or a street rod together needs a selection of these handy puppies on their workbench! Use along with the “Round Bungs” for allen head bolts also available in this catalog. Sold in Pairs. 632701 Round Bung: 1/2” long, 1/2” O.D., 1/4” I.D. For 1/4” socket allen head bolts�������������������������������������������������������������������������$9.99 632702 Round Bung: 5/8” long, 1/2” O.D., 5/16” I.D. For 5/16” socket allen head bolts�������������������������������������������������������������������������$9.99 632703 Round Bung: 3/4” long, 11/16” O.D., 3/8” I.D. For 3/8” socket allen head bolts�������������������������������������������������������������������������$9.99 632704 Round Bung: 7/8” long, 7/8” O.D., 7/16” I.D. For 7/16” socket allen head bolts�������������������������������������������������������������������������$9.99 632693 Round Nut 1/4-20 UNC x 1/2���������������������������������������������������$9.99 632694 Round Nut 1/4-20 UNC x 1�������������������������������������������������������$9.99 632695 Round Nut 5/16-18 UNC x 1/2�������������������������������������������������$9.99 632696 Round Nut 5/16-18 UNC x 1���������������������������������������������������$10.99 632697 Round Nut 3/8-16 UNC x 1/2 �������������������������������������������������$9.99 632698 Round Nut 3/8-16 UNC x 1���������������������������������������������������$11.99 632699 Round Nut 7/16-14 UNC x 1/2�������������������������������������������������$9.99 632700 Round Nut 7/16-14 UNC x 1���������������������������������������������������$11.99

w w w.cu sto m c h ro m e.co m

SHEET.07

SHEETMETAL

19639

Universal Mounting Bracket/Gusset by Vulcan Engineering

Milled from 1018 CF Steel, Not stamped! 3/16” Thick with a 3/8” hole. Perfect for mounting custom exhaust or as a brake anchor mount or any other applications you can come up with. Made in the U.S.A.. Sold each. 668256 Universal bracket/gusset 3/16” thick w/ a 3/8” hole, sold each

������������������������������������������������������������������������������������������������������������$8.99

650246

K&N Reinforced Rubber Fender Washers

1"-diameter round rubber washers have dozens of uses, in addition to the obvious. Allows clean scratch-free, wellcushioned installations. Card of 12 packs of 10. 22170 Fender washers ����������������������$6.17

‘King’ Tanks for Early Sportster Models

2"-wider than the ‘Standard’ tank... enough to give extra mileage and just wide enough to make them look great. These high tunnel tanks are equipped with stock mounts but do not include mounting hardware. They have a 3.1 gallon capacity. 3/8"NPT. 19639 Fits all models from 55-78��������������������������������������������������������$134.99 25574 Fits all models from 79-81��������������������������������������������������������$119.99 650246 Fits all models from 82-92��������������������������������������������������������$119.99

3.5 Gallon Hand Shift Gas Tanks

Two versions of the obsolete hand shift style 3.5 gallon gas tank sets. Accurate placement of the shifter gate lugs and shut-off rod hole centers ensures trouble-free service. Available in two versions. One is a totally accurate reproduction of the original, rod-style gas shut-off equipped tank used from 48-65. The other is based on the same tank, but eliminates the early style gas shut-off rod system and replaces it with the tank bottom fitting for the late 13/16" externalthread petcock. Both tanks accept the correct cam-style gas caps and are designed to accept the stock shifter guide. 25568 Original style with rod shut-off (shown)������������������������������$219.99 25569 Updated style for 75-07 petcock ��������������������������������������������$219.99

‘Peanut’ Tank for Sportster Models

A quality reproduction of the Original Equipment 2.4 gallon gas tank. 12724 Fits early Sportster and K models from 55-78 (replaces OEM 61006-63B) ������������������������������������������������������������������������������������$89.99 Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.

Note: Fuel tanks, particularly where custom paint is planned, must be pressure tested and sealed with CCI tank sealer 670675 before painting to protect the final finish and prevent internal rust.

SHEET.08

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL

600154

Custom Chrome Custom “Low Tunnel” Gas Tank

This 2.8 gallon custom tank features a 1 1/2"-high tunnel with universal style mounts for custom applications. Accepts 3/8" NPT threaded petcock. Tank measures 15 1/2"-long x 9"-wide x 7"-high with a 1 1/2" tunnel. 260121 Unpainted steel����������������������������������������������������������������������������$99.99 Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.

600155

632933

600157

651261

Custom ‘Bobber Style Gas Tanks’ by Cole Foster

An absolutely beautiful new tank designed with the keen styling of Cole Foster - Salinas Boyz Customs. The tanks feature a mini popup gas cap, and a unique raised tapered bead down the center of the tank. Each tank has been designed to fit to stock frames but can also be easily adapted to any custom application. They use the existing stock rubber mounts or are included as needed. Fuel capacity is 2.35 gallons. 600155 Fits Evolution Softail models from 84-99 and 4-speed FX and FL models ������������������������������������������������������������������������������������������$260.99 Note: These applications require the front frame dash mount to be cut off and rear screw hole modified.

600157 600154

Fits carburated Twin Cam 88 Softail models from 00-06 ��������$260.99 Fits Sportster models from 82-03��������������������������������������������$260.99

XL Flat Bottom Standard & King Sportster Tanks by Paughco

Traditional Sportster Standard & King tanks. but modified for universal applications with horseshoe front mounts and tab rear mounts. They are equipped with a bung to accept late model 22mm petcocks and screw-in style gas caps. Made in the U.S.A. 632933 XL Flat Bottom Gas Tank. 2.9 gals.������������������������������������������$179.99 651448 XL 95-03 Flat Bottom King Tank 2.9 gallon��������������������������$179.99 651449 XL 04-06 Flat Bottom King Tank 2.9 gallon��������������������������$219.99 651261 XL Flat Bottom Gas Standard Tank. 2.2-gallon ������������������$180.99

Replacement Gas Caps 47775 Stainless Steel (sold each) ����������������������������������������������������������$42.99 47777 Chrome (sold each)����������������������������������������������������������������������$42.99

w w w.cu sto m c h ro m e.co m

SHEET.09

SHEETMETAL

651285 651260

Custom Narrow Axed style Gas Tank by Paughco

This tank features a low tunnel with straight mounting tabs on both the front and rear, single early cam style gas cap with dual threaded 1/4” fuel outlets. Made in the U.S.A. 651285 2.2 gallon Axed Harley-Style Custom tank with single gas cap 651259

��������������������������������������������������������������������������������������������������������$171.99

670800

Indian Larry ‘Dished’ Tanks The same tanks used on the Indian Larry bike in the build-off series. Old School looks with modern production techniques bring you the cool style you want at an affordable price. Easy mounting by drilling of the backbone and can be adapted to many styles of stock and custom frames. 670800 3.0 Gallon ����������������������������������������������������������������������������������� $369.99 670801 3.5 Gallon ����������������������������������������������������������������������������������� $369.99 651259 4.5 Gallon ����������������������������������������������������������������������������������� $363.99 651260 5.0 Gallon ����������������������������������������������������������������������������������� $363.99

SHEET.10

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL

632930

632931

“Mini Mustang” Gas Tanks by Paughco

These small gas tanks look awesome! Great lines, and only 16 1/2” long, 9” wide and 7” deep. For custom applications with 2 mounting styles available. The Narrow “Mini Mustang” tank has a capacity of 2.4 gals., with tunnel measuring 2 1/4” wide x 2 1/2” deep and front/ rear mount tabs. Total length tab center to tab center is 17”. The Frisco “Mini Mustang” tank has a capacity of 2.2 gals. and features a Frisco style front mount. Tunnel measures 3” wide x 1 1/2” deep, and total length tab center to tab center is 15 1/2”. Both tanks have 2, 1/4” NPT petcock outlets; petcocks sold separately. Made in Nevada, USA by the crew at Paughco.

632930 632931 632252 632253

“Mini Mustang” Gas Tank. Narrow. 2.4 gals. ���������������������$189.99 “Mini Mustang” Gas Tank. Frisco. 2.2 gals.�������������������������$189.99 1/4” NPT Petcock. No reserve. (see petcocks) �����������������������$27.99 1/4” NPT Petcock. With reserve. (see petcocks) �������������������$45.99

Mustang Gas Tank with Pop-Up Cap

3.3 Gallon Mustang Tank

This one piece tank is perfect for a variety of custom applications. It has rounded mounting plates front and rear that are welded in place. It features a twin cap look, but the left neck is non-functional, for appearance only. The 3.3 gallon capacity tank fills on the right-side only. Tunnel measures 2 1/2"-high x 2 3/4"-wide. Tank measures 18 1/2"-long x 12"-wide. 260143 Unpainted steel��������������������������������������������������������������������������$103.99 Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.

Comes with a center-mounted single “pop-up” gas cap and has a capacity of 3.3 gallons. Tank measures 16 1/2"-long x 11"-wide at widest point. Total length from tip-to-tip of mounting brackets is approximately 20". Tunnel is approximately 2 3/4"-wide x 2 1/2"deep. Features a 3/8" NPT gas outlet (use CC #’s 12726 or 12727 petcocks) on the center of the bottom right side as well as two 1/4" gas outlets (use CC #’s 632252 or 632253 petcocks) on both sides near the rear of the tank to be used as a crossover line or, for multiple choices in routing your gas lines. Petcocks sold separately. 632165 Mustang tank with pop-up cap�����������������������������������������$169.99 Special Flush Mount Pop Up Gas Cap 675706 Required for CC # 632165 �����������������������������������������������������$54.99 Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.

w w w.cu sto m c h ro m e.co m

SHEET.11

SHEETMETAL

651251

Mustang and Axed Harley-Style Custom Gas Tanks by Paughco

Available in two popular styles that will bolt right to the stock frame mounts on 57-03 Sportsters and have an early cam-style gas cap bung. Made in the U.S.A. Fits Sportster Models from 82-94; with a 22mm threaded fuel bung on the right-side of the tank 651251 4.2-gallon Axed Style Custom tank with single gas cap for 82-94 XL�������������������������������������������������������������������$205.99 651252 3-gallon Mustang Style tank with single gas cap for 82-94 XL�������������������������������������������������������������������������$205.99 Fits Sportster Models from 95-03; with a 22mm threaded fuel bung on the left-side of the tank 651253 4.2-gallon Axed Style Custom tank with single gas cap for 95-03 XL�������������������������������������������������������������������$205.99 651254 3-gallon Mustang Style tank with single gas cap for 95-03 XL�������������������������������������������������������������������������$205.99

651252

632251

651241

Narrow “Mustang” Style Tank

This sleek looking gas tank features dual bung type caps, holds 2.2 gallons of gas and measures 16 1/2” long, 9” wide and 7” deep. Tunnel is 2 1/2” wide x 2 1/4” deep. Center line hole-to-hole on mounting tabs is 17 1/2”. Tank has two 1/4” gas outlets (use our #632252 or 632253 petcocks). This is a sweet looking tank and goes great with narrow springers or our girder set-up. Gas caps and petcocks not included. Made in USA by Paughco. 632251 2.2 gal dual cap narrow mustang type tank������������������������$205.99 651241 2.2 gal single cap narrow mustang tank ������������������������������$189.99

SHEET.12

“Wasp” Custom Chopper Gas Tank

Building a trick chopper but haven’t found the prefect tank for it yet? Look no further! This 2.2 gallon tank with it’s tear drop shape is perfect for any retro scoot. Available with one or two cam style bungs, TIG welded with the petcock bung on the right side. 651017 Wasp chopper tank��������������������������������������������������������������������$139.99 651018 Wasp chopper tank dual cap ��������������������������������������������������$144.99

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL 25242 25241

Universal Tank Mounting Kit for Builders

Building your own tank you say, well how are you going to mount it? This complete set of tank mounts comes with not only the straps and rubber mounting parts to go on the frame, but also the machined blocks that are welded into the fuel tank for them to bolt to. 699985 Complete kit����������������������������������������������������������������������������������$72.99

25246

25253

25252

Chrome Replacement Petcocks

Chrome-plated duplicates of the stock gas valves used from 75-06. Available in three different outlet tube options, straight down, left-hand or right-hand for applications at the front, rear, or either side of the gas tanks. Complete with a chromed 13/16" nut and nylon mesh filter screen. 25246 Straight down spigot (repl. OEM 62129-75T)�������������������$14.99

25252 25253 25241 25242 12731

Left-side spigot�������������������������������������������������������������������������$17.99 Right-side spigot ���������������������������������������������������������������������$14.99 Short replacement filter screen ��������������������������������������������� $5.99 OEM replacement filter screen with reserve tube (repl. OEM 62166-81)������������������������������������������������������������������������������������� $5.99 Replacement 3-hole Viton seal (fits latest design with .260" fuel tubes)����������������������������������������������������������������������������������� $1.50

Replacement Filter Screens 260373 Fits OEM pre-75������������������������������������������������������������������������������� $3.99

Mounting Kit for Fat Bob Tanks

A ‘must’ when installing CC or Original Equipment Fat Bob tanks on 4-speed frames through 84. Special washers in kit prevent possible thread damage to rear mounting holes and keep tanks from resting against heads. 26446 Complete kit������������������������������������������������������������������������������������$9.99 Another ‘must’ for installing Fat Bob tanks. One of our mechanics came up with this little item. It’s actually the chain guard mounting grommet, but it works great in the front Fat Bob tank mount holes to isolate the tanks from vibration. 25548 Rubber grommet with a steel insert for use in mounting Fat Bob tanks. Helps to isolate the tanks from vibration. Pack of 10 (repl. OEM 11411)��������������������������������������������������������������������������$0.65

12726

12727

25245

25243

Chrome Petcocks

Universal Fat Bob Gas Tank Quickmount Kit

A precise and effortless way to mount Original Equipment or aftermarket Fat Bob tanks to custom or Original Equipment frames that have had the gas tank brackets removed. It permits the builder to temporarily attach the one-piece bracket for a quick visual check of tank placement on custom applications, and once a tank position is selected, the entire bracket assembly may be welded in place for a stronger-than-stock, precision system of support. 25048 Complete kit����������������������������������������������������������������������������������$49.99

Engineered and designed to eliminate all internal O-rings. The innercore design insures against gas leakage while providing maximum flow. Features a filter screen, reserve setting, and chrome body. 12726 Fits OEM and custom tanks thru 74 with internal 3/8" NPT connection (repl. OEM 62125-55B)���������������������������������� $15.99 12727 3/8” NPT Petcock w/90 degree outlet. With reserve. (see petcocks) �����������������������������������������������������������������������������������������$15.99 25245 Fits OEM and custom tanks 75-82 with external 13/16" nut connection (repl. OEM 62163-75) ������������������������������������ $14.99 25243 Same fit as CC #25245 but with 90° barb���������������������������$14.99

w w w.cu sto m c h ro m e.co m

SHEET.13

SHEETMETAL

632253 18255 651854 632252

Chrome Fuel Filter

Small size, but packs big protection for your motor. Easily cleaned, reusable screen. Chrome 18255 For 5/16" fuel line ��������������������������������������������������������������������������$8.99 18256 For 1/4" fuel line ����������������������������������������������������������������������������$6.99

1/4” Petcocks for Custom Tanks

These petcocks are available with or without the reserve feature, and fit any custom gas tank such as our aluminum peanut tank (#632501) and Paughco gas tanks that take 1/4” petcocks. 632252 1/4” NPT Petcock. No reserve. (see petcocks) ����������������������� $27.99 632253 1/4” NPT Petcock. With reserve. (see petcocks) ����������������� $45.99

Black 651855 651854

For 5/16" fuel line ��������������������������������������������������������������������������$6.99 For 1/4" fuel line ����������������������������������������������������������������������������$6.99

27050 27051 18240

See-Flow Glass Fuel Filters

668376

Accel High-Flow Petcocks

American-made high-flow petcocks feature chrome-plated bodies and 5/16" O.D. hose barbs. Other features include a reserve function, 100 micron filtering screens, and easy-to-grasp handles. Bodies are engineered to prevent leakage, yet deliver maximum fuel flow for high-performance applications. Two of the petcocks have a swiveling banjo which rotates 180° for custom hose routing. Fit all Original Equipment or aftermarket tanks with 22mm bungs. 27051 Petcock with horizontally rotating barb ��������������������������������$99.99 27050 Petcock with straight down barb ��������������������������������������������$79.99 668376 Petcock with vertically rotating barb��������������������������������������$99.99

SHEET.14

A custom in-line fuel filter for 1/4" or 5/16" line. Chrome 18240 Complete filter for 1/4" line������������������������������������������������ $9.99 18239 Complete filter for 5/16" line���������������������������������������������� $9.99 Black 651856 651857

Black filter for 1/4” line ����������������������������������������������������������������$9.49 Black filter for 5/16” line��������������������������������������������������������������$9.49

Replacement filter element 18241 Replacement element ����������������������������������������������������������������$2.99

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL

Dash Panels for Fat Bob Tanks Chrome Tank Panel

Fits most models with split tanks, cast dash and a frame-mounted seat from 68-99. 18439 Replaces OEM 61118-81������������$27.99

Fits FX and Low Rider models with Fat Bob gas tanks from 77-84. 26348 Plain (repl. OEM 61647-77T)����$24.99

Steel Chrome Dash for FX Models

Dash Panel for Fat Bob Gas Tanks

Fits Fat Bob gas tanks when dash or instruments are not mounted on tanks. 26344 Plain ����������������������������������������������$24.99

Stamped steel, chrome-plated instrument housing for tank mounted gauges on FX models from 77-84. Includes thick style tank-to-housing trim rubber and warning light hole plugs for custom applications. 26339 Dash cover������������������������������������$39.99 26338 Replacement trim rubber (repl. OEM 61401-82)����������������������������������������$4.99 26308 Hole plugs (pack of 10) ��������������$1.50

Chrome Dash Kit

All the chrome parts in one convenient kit to help you convert to the dash used on several models 77-84. Will not work with flatside gas tanks. 91339 Complete kit���������������������������$55.99

Chrome Skull Nut Cover

Made in the U.S.A. by Wild 1 Mfg. to cover the hardware that holds the dash in place. Kits include red rhinestones for the eyes. Fits the cast dash on models without a dashmounted choke cable. 19971 Sold each��������������������������������������$17.99

632040 632041

Dash Center Mounting Bolt and Stud

Gas Tank Knee Pads

These universal fit rubber knee pads affix to your tank with double sided adhesive (included) and give tanks a very cool old school look! Available in 2 sizes to match most any tank configuration out there. The smaller size measures approx. 7” long x 3 1/2” tall at the highest point. The larger version measures approx. 7” long x 4” tall at the highest point. Stick these puppies on your tank and stand out from the crowd! Sold as pairs. 632040 Gas tank knee pads-Small����������������������������������������������������������������������������������������������������������� $21.99 632041 Gas tank knee pads-Large����������������������������������������������������������������������������������������������������������� $29.99

Includes chrome-plated center screw with stud and hardware. Fits Big Twins from 47-67 as original part replacement or can be used on custom applications where choke wire is not brought through dash. 26162 Sold each����������������������������������������$5.99

w w w.cu sto m c h ro m e.co m

SHEET.15

SHEETMETAL

26188

Three-Light Dash Mounting Plate 25972

Two-Light and Three-Light Dashes for Fat Bob Tanks

Show-chrome dash covers complete with lenses and trim rubber. Replacement lenses and trim rubber also available separately. 26188 2-light dash����������������������������������$44.99 25972 3-light dash����������������������������������$40.99 26180 Replacement trim rubber ����������$4.99

Classic Cast Dashes

Heavy-duty zinc die-cast dashes are beautifully chrome-plated duplicates of their Original Equipment counterparts. Complete in every detail, each dash also includes the lenses, light divider, and trim rubbers. May be installed on most 4-speed frames and Softail models when the appropriate dash base is used. 26187 Fits all models 68-90 (replaces OEM 71241-68B)������������������������������������$69.99 26186 Fits all models with self-cancelling turn signals from 91-95 (except Dyna Wide Glide models) replaces OEM 71241-91 ����������������������������$69.99

Includes wiring and sockets. 25971 Fits CC dash #25972��������������������$39.99 26191 Replacement dash base light sockets (pack of five)��������������������������������$22.99

Replacement Parts These pieces will fit Original Equipment dashes as well as the dashes listed above. 26239 Lens kit: Includes lenses, divider and hardware����������������������������������������$9.99 26240 Trim rubbers (pair) replaces OEM 71295-68 ����������������������������������������$4.99 26238 Cast dash mounting plate��������$44.99

Late-Style Cast Dash Mounting Plate

A complete mounting kit for many models with cast dashes from 68-99 (except Dyna Wide Glide models). Includes all the hardware and spacers necessary to fit both the standard early-style Fat Bob tanks and the later-style flatside Fat Bob tanks. Also included are the circuit breaker clips, the rubber strip for mounting circuit breakers with flatside tanks, ignition switch mounting screws, three insulated terminal studs and five light sockets with bulbs. Everything necessary for a quick and easy installation. 26238 Cast dash mounting plate��������$44.99 26191 Replacement dash base light sockets (pack of five)��������������������������������$22.99

Plain Dash Mounting Plate Cateye Dash for Fat Bob Tanks

Show-chrome cateye-style dash with lenses. Replacement lenses are sold each. 26189 Cateye dash����������������������������������$39.99 26356 Cateye red lens-plastic ����������������$4.99

SHEET.16

Basic mounting plate for use with Fat Bob dash covers #25972 and #26188 when dash lighting is not desired. 25235 Without dash lights��������������������$14.99

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL

Odometer Reset Cable for FX Models

Trimlok Dash Trim

Easy-to-install, while providing style and protection. Genuine Trimlok steel reinforced vinyl trim is cut to length to fit all stamped steel two and three-light dashes. Available in pre-cut 27 inch and 10 foot lengths in plain black. 26181 Black (27"-long)������������������������������������������������������������������������������$4.99 26241 Black (10 feet-long)������������������������������������������������������������������������$1.00

Complete odometer reset cable assembly for all 4-speed FX models (except FXWG) 73-84. Includes chrome knurled knob, rubber grommet, washer, spring and flexible cable. Fully assembled, ready to install. 26445 Replaces OEM 67210-73T�������������������������������������������������������$10.99

Hi-Beam Indicator Lamp

Original style, multi-piece high beam indicator lamp assembly with replaceable bulb included. Fits FX models from 73-74, as well as Sportster models from 68-73. Can also be used to replace the onepiece ‘throwaway’ indicator lamp used on FX models from 75-85. 26444 Replaces OEM 67891-68�����������������������������������������������������������$8.99

Trim Rubber for Low Rider Dash

Thick style, black rubber trim for FX dual gauge housings. Neatly fills the open space between the tanks and the instrument housing while isolating the gauges from vibration. 26338 Replacement trim rubber (repl. OEM 61401-82) ��������������������$4.99

310154 26356

26352

Dash Switch Decal

Fits FL models from 68-84, FX models from 71-72, FXWG models from 80-86, and Softail models from 84-99. Sold in pack of 5. 310136 Replaces OEM 71300-79 �������������������������������������������$2.00

26353

26354

Replacement Lenses for Fat Bob Dash Covers

Can be used to restore Original Equipment dashes or as replacement parts for CC dashes. Sold each. 26356 Cateye red lens-plastic �������������������������������������������������������������$4.99 26354 3-light dash red lens (2 used) – plastic ���������������������������������$5.99 26353 3-light dash blue lens (1 used) – plastic �������������������������������$5.99 26352 2-light dash red lens – plastic�������������������������������������������������$4.99 310154 Cateye dash lens, green�����������������������������������������������������������$4.99

Instrument Light Socket Assemblies

OEM style replacement light socket assemblies include socket with wire and bulb. Available for most Big Twins and Sportster models 76-97. Sold in 5 packs. 310113 Steel, 1 wire type��������������������������$4.80

Chrome Dash Cover Screws

Complete 4-piece set of chrome plated, buttonhead panel screws. Fit all Low Rider and FXEF dashes 77-84. 26441 Set of 4�����������������������������������������������������������������������������������������$3.99

w w w.cu sto m c h ro m e.co m

SHEET.17

SHEETMETAL 260032 260005

688531

Deluxe Scalloped Gas Caps

Chrome deluxe gas caps with scalloped edges. Available vented or non-vented for most Big Twin and Sportster models. Also fits most after-market replacement gas tanks. For 41-73 models 260030 Vented ��������������������������������������������������������������������������������������������$15.99 260031 Non-Vented������������������������������������������������������������������������������������$15.99 260032 Deluxe gas cap set (one vented and one non-vented cap)

�����������������������������������������������������������������������������������������������������$29.99

For 84-95 models 688530 Deluxe gas cap set chrome (one vented and one non-vented cap)��������������������������������������������������������������������������������������������������$38.99 688531 Deluxe vented gas cap chrome ������������������������������������������������$19.99 688532 Deluxe non-vented gas cap chrome����������������������������������������$19.99 688536 Deluxe gas cap set black (one vented and one non-vented cap) 688537 688538

651863

Early-Style Gas Caps for Late 65-72

����������������������������������������������������������������������������������������������������������$38.99

Chrome gas caps for Big Twin and Sportster models from 65-72 (except FLT and FXR models). Chrome 260003 Vented (repl. OEM 61103-35)������������������������������������������������������$8.99 260005 Gas cap set. Includes one vented and one non-vented (repl. OEMs 61103-35 and 61103-65)��������������������������������������������������$16.99

Deluxe vented gas cap black������������������������������������������������������$19.99 Deluxe non-vented gas cap black ��������������������������������������������$19.99

Black 651863

For 96-Up models 688533 Deluxe gas cap set chrome (one vented and one non-vented cap)��������������������������������������������������������������������������������������������������$38.99 688534 Deluxe vented gas cap chrome ������������������������������������������������$19.99 688535 Deluxe non-vented gas cap chrome����������������������������������������$19.99 688539 Deluxe gas cap set black (one vented and one non-vented cap)

651864

Black gas cap set. Includes one vented and one non-vented (repl. OEMs 61103-35 and 61103-65) ��������������������������������������$11.99 Black vented (repl. OEM 61103-35)��������������������������������������������$6.49

����������������������������������������������������������������������������������������������������������$38.99

688540 688541

Deluxe vented gas cap black������������������������������������������������������$19.99 Deluxe non-vented gas cap black ��������������������������������������������$19.99

Original-Style

Cam-Style Gas Caps

651853

Steel Gas Caps

26580

Perfect mechanical reproductions of the Original Equipment parts. The low-pressure relief vent is properly recessed in the cap to clear the filler neck vent tube. For screw-style tanks from 83-95. Chrome 26580 Set of left and right caps������������������������������������������������������������$21.99 26582 Right side cap only (vented) replaces OEM 61102-83A ������$10.99 26581 Left side cap only (non-vented) replaces OEM 61103-83����$11.49 Black 651862 651853 651861

SHEET.18

Black set of left and right caps��������������������������������������������������$21.99 Black right side cap only (vented) replaces OEM 61102-83A

����������������������������������������������������������������������������������������������������������$10.99

Late-Style

A variety of replacement and custom gas caps. Available vented for single cap gas tanks and the right side of Fat Bob gas tanks, or without a vent for the left side of Fat Bob tanks. They fit Original Equipment and replacement tanks with cam-style bungs. Polished Stainless Steel Late-Style Caps Includes left and right caps for Fat Bob tanks. 26574 Plain cap set ����������������������������������������������������������������������������������$29.99 26570 Vented cap ONLY (repl. OEM 61102-73) ��������������������������������$14.99 26571 Non-vented cap ONLY (repl. OEM 61103-73A)����������������������$14.49 Chrome Original-Style Gas Caps Includes left and right caps for Fat Bob tanks. 26499 Plain cap set ����������������������������������������������������������������������������������$11.99 12725 Plain vented cap ONLY (repl. OEM 61103-36)��������������������������$9.99 26021 Plain non-vented cap ONLY (repl. OEM 61103-65) ����������������$7.99

Black left side cap only (non-vented) replaces OEM 61103-83

�����������������������������������������������������������������������������������������������������$10.99 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL 47715

Custom Pop-Up Gas Caps

• Vented gas caps that don’t protrude from the surface of the gas tank at all! • To access the filler, you press and twist... the cap pops up, then unscrews normally • For custom “weld-in” applications ONLY • Sold each 47715 Stainless steel bung and cap�����������������������������$99.99 Replacement Pop-Up Caps ONLY 47775 Stainless Steel (sold each) ���������������������������������$42.99 47777 Chrome (sold each)���������������������������������������������$42.99

Custom Mini Gas Cap Kit

The gas cap is CNC-Machined from billet aluminum with a knurled edge with a satin/raw finish (gas cap has an O.D. of 1.75”). Kit comes complete with gas cap and steel weld-in bung. 641909 Mini weld-in gas cap����������������������������������������������������������������������������������������$39.99

Polished Aluminum Skull Gas Cap Cover

Multiple skull design cast from an original hand-carved mold . Attaches to OEM style gas caps with epoxy (not included). 37735 Sold each���������������������������������������������������������������$21.99

19037

19006

‘Live To Ride’ Gas Cap Covers

Covers with chrome eagles feature a ‘A Way of Life’ banner. Gold eagles have ‘Eagle Spirit’ banners. They attach with double-sided foam tape and fit all late model gas caps (except molded plastic caps). ‘A Way of Life’ 19006 Chrome eagle (sold each) ������������������������������������������������������������������������������$10.99

3-Dimensional Gas Cap Covers

Distinctive covers are sand-cast from hand-carved originals. Designed to fit over OEM style caps. Glue them on with 5-minute epoxy, or use silicone adhesive. Sold each. 37863 Skull �����������������������������������������������������������������������$38.99 37868 Flame ���������������������������������������������������������������������$27.99

‘Eagle Spirit’ 19037 Gold eagle (sold in pairs)��������������������������������������������������������������������������������$33.99

w w w.cu sto m c h ro m e.co m

SHEET.19

SHEETMETAL

650231

Custom 3 qt. ‘Barrel’ Style Oil Tanks by Santee Chrome Oil Tank for FXR Models

A complete chrome oil tank assembly for all FXR models from 82-90 (except 86-up FXR Super Glide models). Adds sensational style and simplifies oil draining through the addition of a second drain hole on the left rear of the tank. Included with the tank is a remote drain hose fitting kit which allows it to be drained from the kickstand side through a rubber hose which, when not in use, plugs onto a frame mounted dummy fitting which is included in the kit. Machine polished and then triple chrome-plated. Replaces OEMs 62406-81, 62406-86 and 62414-86. 28104 Oil tank and remote drain kit (this tank has no oil level "sight" glass)����������������������������������������������������������������������������������������������$119.99 16051 Well-nuts blind fasteners (repl. OEM 8099) pack of 10 ��������$1.30

These Chrome steel oil tanks were styled after the classic ‘Barrel’ tanks on choppers from the 60’s and 70’s. They have a universal mounting system so they will fit just about anything and are available with or without a spin-on filter. Kits include 3 rubber mounts and tank cap. 650231 3 qt. round oil tank������������������������������������������������������������������� $329.99 650232 3 qt. round oil tank with spin-on filter��������������������������������� $379.99

650235 651266

78305

Chrome Wrap-Around Oil Tank by Santee 78301

Chrome Replacement Oil Tanks

These 4 qt. oil tanks will fit rigid frames and 58-64 swingarm frames with kickstart and steel primaries, but will NOT fit models with aluminum primaries or 79-84 4-speed transmissions. 650235 Chrome center fill oil tank ������������������������������������������������������$165.99 651266 Chrome side fill oil tank with spin-on oil filter��������������������$339.99

Duplicates of the Original Equipment oil talks finished in brilliant chrome. 78301 Fits 4-speed FL and FX Big Twin models from 82-86 (repl. OEM 62504-82)��������������������������������������������������������������������������������������$149.99 78305 Fits 4-speed FL and FX Big Twin models from 65-E82 (repl. OEM 62504-65A) ����������������������������������������������������������������������������������$124.99 650219

650218

Oil Tanks for XL Rigid Frames by Paughco

This oil tank is for use with rigid Sportster frames manufactured by Paughco. Drain plug sold separately. Made in USA by Paughco. 632247 Oil tank for use w/Paughco XL rigid frames������������������������$175.99 632248 Oil tank drain plug ������������������������������������������������������������������������$7.99

SHEET.20

Custom Oil Tanks for FL/FX Models and Santee 4-speed Swingarm Frames

3.5 qt. chrome oil tanks for 65-86 FL and FX 4-speed models, that provide easy access to the battery, and bolt to the stock mounts. They will also fit Santee 4-speed swingarm frames. Kits include oil tank and 2-pc. front mounting bracket for an easy installation. 650218 Chrome side fill������������������������������������������������������������������������$339.99 650219 Chrome side fill with spin-on filter������������������������������������$369.99

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL 27101

27100

Bobber-Style Oil Tanks with Battery Box

Here is a old school oil tank for your next bobber bike project. Chrome steel tanks with built-in battery boxes come with front rubber mount and tank cap included. They fit Big Twin rigid frames from 36-57 and most custom rigid frames on the market today, also 84-99 Softail models. Lines come out of the bottom of the tank for a nice clean look. 632062 ‘Domed’ oil tank ������������������������������������������������������������������������$299.99

Chrome Oil Tank Dipsticks

Chrome-plated replacements for Original Equipment dipsticks. 27100 With short dipstick for Softail models from 84-99 and Sportster models from 82-03 (repl. OEM 62595-82A)�������$8.99 27101 With long dipstick for FL models from 70-84, FX models from 71-85, FXR models from 82-83, FLT models from 80-86 and XLCH models from 70-78 (repl. OEM 62625-70A)�����$8.99

650233

Oil Tank Plug Custom Wrap-Around Oil Tanks for Big Twins by Santee

Chrome-cap oil tank super plug for all Original Equipment side-fill oil tanks from 65-99 and most custom tanks. 25674 Replaces OEM 62644-84T���������������������������������������������������������$5.99

3.5 qt. custom wrap-around oil tanks. Available with or without spin-on oil filter and in either a side or center fill. When used with an FXE battery they’ll fit rigid and 58-64 swingarm frames, and will also clear 79-84 4-speed transmissions. Side Fill 650233 Custom 3.5 qt. oil tank with threaded oil line fittings������$239.99 650234 Custom 3.5 qt. oil tank with threaded oil line fittings and spinon filter ����������������������������������������������������������������������������������������$324.99

651262 651263

Wrap-Around Oil Tank for Electric Start Sportster Models

This 3 1/2 quart oil tank will accept the stock FXE electric start battery. It also fits all 67-78 stock electric start Sportster models, and is adaptable to many custom frames (on 73-78 stock frames, the removal of the rear frame support struts may be required).Comes complete with a cap, oil line fittings, and mounting hardware. 12599 Chrome oil tank��������������������������������������������������������������������������$239.99

Replacement Oil Tank Caps by Paughco

Replacement oil tank caps for most side and center fill oil tanks. Made in the U.S.A. 651262 Chrome-plated 1 1/16”-24 threaded cap for top fill oil tanks

�����������������������������������������������������������������������������������������������������$26.99

651263

Chrome-plated push-in rubber filler plug for side fill oil tanks�������������������������������������������������������������������������������������������$14.99

w w w.cu sto m c h ro m e.co m

SHEET.21

SHEETMETAL

Chrome Oil Tank Cap Assembly

For stock oil tanks on all 4-speed Big Twin models (except Softail models) thru 82 and 67-E78 Sportster models with electric start. 12352 Replaces OEM 62610-52TA ��������������������������������������������������������$27.99 25334 Oil tank gasket 66-82 (pack of 10) replaces OEM 62628-66

���������������������������������������������������������������������������������������������������� $0.85

Early-Style Accessory Oil Filter System

Accurate reproduction of the early accessory oil filter kit used on 40-64 Big Twins. Can be easily fitted to 4-speed and Softail models. 26652 Chrome oil filter assembly with gasket kit and filter (replaces OEMs 63800-48 and 63800-58)�����������������������������������������������$52.99 26656 Gasket kit for oil filter assembly ������������������������������������������������$4.99 26657 Filter element (sold each) ������������������������������������������������������������$3.49 Note: Does not include oil hose.

270019

Generator Oil Filter Adapter

This adaptor allows you to install an oil filter in place of the generator on 36-69 motors as well as our Pandemonium or S&S Shovelhead engines with generator/alternator bottoms. Use OEM 63796-77A or equivalent aftermarket oil filter. Chrome finish. 632025 Generator oil filter adapter ����������������������������������������������������$114.99

633244 633245

25247

25248

Oil Filter Kits

Full flow automotive style spin-on oil filter kits. Each of these custom kits includes a chromed heavy-gauge steel bracket, chrome disposable oil filter, and all required hoses and clamps for installation. 25247 Fits all 70-78 Big Twins without front motor mounted rectifier/ regulator (mounts on top of front motor mount) ��������������$57.99 25248 For all Sportster models 57-77 (mounts to left front motor mount location)����������������������������������������������������������������������������$55.99 270019 Fits frame tubes, excellent for custom applications ������������$51.99 25250 Chrome oil filter (replaces OEM #63796-77A) ������������������ $8.99

Chrome Oil Fitting 1/4 NPT x 90 and Hose Barb 1/4 NPT x 3/8

Oil line fittings and hose barbs to connect oil lines to Santee oil tanks (CCI# 631990-91) Oil line fitting 633244 1/4 NPT x 90��������������������������������������������������������������������������������������$7.49 Hose Barbs 633245 1/4 NPT x 3/8������������������������������������������������������������������������������������$5.99

SHEET.22

Rubber Mounts

Replacement rubber mount is used for mounting Harley battery boxes and oil tanks. Made of quality rubber with 1/4"-20 x 1/2" long threaded studs and steel plates. This mount also works great for mounting many custom parts. Replaces OEM 62563-65. 16055 Pack of 10 ����������������������������������������������������������������������������������������$2.80

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL

16050

Rubber Vibration Resistant Mounting Studs

This is just the answer for custom builders. These studs are perfect for mounting gas and oil tanks. Sold in packs of 5 (unless otherwise noted). 16050 1/4"-20 x 1/2" stud both ends�������������������������������������������������$1.80

Spin-On Oil Filter Kit

A high-tech replacement for your canister-type oil filters. It’s approximately the same size as the stock unit and accepts CC #25250 chrome spin-on filter to eliminate leaks. Makes filter changes clean and easy. Comes with both threaded and slip-on fittings. Uses our mounting brackets. 26650 Spin-on filter kit����������������������������������������������������������������������������$53.99 25250 Chrome oil filter (replaces OEM #63796-77A) ������������������������$8.99

26653

26654

26655

Oil Filter Mounting Brackets

Chrome steel brackets to mount accessory oil filters. Designed for use in conjunction with CC #’s 26650 or 26652 oil filter kits. Available for rigid and swingarm 4-speed Big Twin frames from 40-86. 26653 Fits 40-57 rigid frames (repl. OEM 63860-50) ��������������������������$9.99 26654 Fits 58-64 swingarm frames (repl. OEM 63860-58A)��������������$9.99 26655 Fits 65-86 4-speed frames (except Softail models)������������������$9.99

Crimp Hose Clamps

OEM style hose clamps. Note: Diameters listed are before crimping. Sold in packs of 50. 260482 17/32" (.531) diameter. Fits 1/4" I.D. reinforced rubber fuel line and vent hoses (repl. OEM 10014)���������������������������������$0.32 260483 19/32" (.594) diameter. Fits 5/16" I.D. rubber remote brake reservoir hose (repl. OEM 10038)�������������������������������������������$0.32 260484 11/16" (.687) diameter. Fits 3/8" I.D. reinforced rubber oil and vent hoses (repl. OEM 10020A) �������������������������������������$0.32 260485 13/16" (.812) diameter. Fits all tank drain hoses (repl. OEM 10086)�������������������������������������������������������������������������������������������$0.32

020538

Oil Line Fittings

Chrome fittings used for oil tank, oil pump, oil coolers, carb fuel inlet, etc. Sold in 5 pack. 020531 Straight fitting. 3/8" hose to 1/8" NPT. Replaces OEM 63533-41

�����������������������������������������������������������������������������������������������������������$1.60

Filter Pac

Custom oil filter and regulator mount designed to clean-up front lower mount area. Attaches to the front of the engine. Includes a chrome billet aluminum base plate, chrome hose fittings and a chrome oil filter. Utilizes stock regulator. Fits all Softail and 4-speed Big Twin models from 75-99. 25270 Complete kit����������������������������������������������������������������������������������$64.99 26109 Replacement chrome oil filter (replaces OEM 63782-80)������$6.99

020533 Straight fitting. 5/16" hose to 1/8" NPT �����������������������������������$4.00 020535 Straight fitting. 5/16" hose to 1/4" NPT �����������������������������������$3.80 020536 90° fitting. 5/16" hose to 1/8" NPT. Replaces OEM 62375-57

�����������������������������������������������������������������������������������������������������������$6.80

020538 Plug – 1/8" NPT (repl. OEM 42311-58)���������������������������������������$3.00 020539 Pipe plug, 1/4" NPT �����������������������������������������������������������������������$3.60

w w w.cu sto m c h ro m e.co m

SHEET.23

SHEETMETAL 688250

688251

84753

Oil Line Retainers for Twin Cam Models

Every time the oil lines are removed from the oil tank these retainers should be replaced in order to avoid any leakage. 688250 Oil line retainers (pr) to engine OEM 63632-00������������������� $14.99 688251 Oil line retainers (pr) to tank OEM 63783-00 ����������������������� $14.99

20235

20234

Oil Line T-Piece and Fittings

Brass T-piece with 3/8" spigot and chrome-plated oil line fittings with 1/8" NPT thread and 3/8" spigot. Sold each. 84753 Brass T-piece ������������������������������������������������������������������������������������$8.15 20235 Chrome hose fitting, 3/8" hose. (repl. OEM 63533-41) Sold each

������������������������������������������������������������������������������������������������������������$4.99

20234

12533

Elbow, 90°����������������������������������������������������������������������������������������$4.99

12534

Original-Style Oil Pump Fittings

Original-style fittings used with some custom oil tanks to convert nipples so stainless-steel braided lines may be used. Set of 3. 12533 Fit nylon and braided hose����������������������������������������������������������$7.99 12534 Fit steel and braided fixed-end lines��������������������������������������� $12.99

SHEET.24

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL 270609 270608

270606

Custom Hose Clamps

Fits over oil and fuel lines. Available with chrome or blue anodized finish. Sold in 6 packs. 270600 Chrome. Fits 3/8" and 5/16" I.D. hoses (up to 5/8" O.D.)����������������$4.33 270604 Blue. Fits 3/8" and 5/16" I.D. hoses (up to 5/8" O.D.) ��������������������������$4.17 270601 Chrome. Fits 1/4" I.D. hose (up to 1/2" O.D.)����������������������������������������$4.17 270605 Blue. Fits 1/4" I.D. hose (up to 1/2" O.D.)������������������������������������������������$4.17

270607

Custom Hose Clamps

Mini Hose Clamps

Quality clamps for all 7/32" to 5/8" O.D. hose. 19883 Card of 24 ��������������������������������������$0.83 19878 Box of 10����������������������������������������$0.70

These custom hose clamps feature a great look with reliable function. Under each custom hose cover is a weather resistant worm-drive hose clamp. Sold in packs of 6. 270606 3/8"-diameter. Slotted ����������������$4.33 270607 1/4"-diameter. Slotted ����������������$4.33 270608 3/8"-diameter. Grooved��������������$4.17 270609 1/4"-diameter. Grooved��������������$4.17 380305

380351

380300

380303

380302

380353 380301 380352

Hose Separators

Available in plain or ball milled to match our other custom accessories, these die-cast hose separators will fit 3/8" or 5/16" I.D. rubber or stainless steel oil and fuel lines on Big Twin and Sportster models. Sold each. Ball Milled

Price

Plain

Price

380300

$7.99

78396

$7.49 Chrome

380301

$7.99

380351

$7.49 Polished

380302

$6.99

380352

$6.99 Blue

380303

$7.99

380353

$7.49 Black

Triple Hose Separator

Keep lines neatly bundled with these separators fit 3/8" or 5/16" rubber or stainless steel hoses. Secures with flush sockethead screws. 380305 Chrome�������������������������������������������$9.99 380355 Chrome ball milled ����������������������$9.99

25460

Oil Pressure Switch

Quality replacement oil pressure switch for XL and K models 54-76 and Big Twin (except Evo) 41-84. Replaces OEM 2655272, sold each. 688594 Oil pressure switch (repl. OEM 26552-72)��������������������������������������$10.99

17714

Oil Pressure Switches

25464

25463

Accel Oil Pressure Switches

Replacement switch has heavy-duty contacts and thermoplastic insulator. Made in the USA. Fits FXD 99, Big Twin 99-13 (except models with electric oil pressure gauges). 17714 Oil pressure switch. Replaces OEM 26561-84����������������������������������$10.99

American-made units with heavy-duty contacts, brass ferrule, thermoplastic insulator and a bright finish. Fits Sportster and K models from 54-76 and Big Twins from 41-84 (except Evolution models). 25460 Replaces OEM 26552-72������������$15.99

Oil Pressure Switch Wrench

Avoid scratching or damaging your oil pressure switch during installation or removal with this handy two piece tool. 688722 Oil pressure switch wrench������$17.99

Fits Sportster models from 77-03 25463 Replaces OEM 26554-77������������$16.99 Fits Evolution Big Twin models from 84-99 (except models with electric oil pressure gauge) 25464 Replaces OEM 26561-84������������$13.99

w w w.cu sto m c h ro m e.co m

688635

Twin Cam Oil Pressure Switch

Oil pressure switch for all Twin Cam models and V-rod models 02-Up. Sold each. 688635 Oil pressure switch (repl. OEM 26561-99)����������������������������������������$5.99

SHEET.25

SHEETMETAL

260530 614004

Stainless Steel Braided Hose

Sold in 25 ft. rolls. 260530 1/4" ID x 25’������������������������������������������������������������������������������������$79.99 260532 5/16" ID x 25’ ��������������������������������������������������������������������������������$87.99 260534 3/8" ID x 25’������������������������������������������������������������������������������������$99.99

12428

Goodridge “All Black 210 Oil Line Kits”

All black oil line kits for V-Twins. Featuring our premium black braided oil hose. Hose has outer fabric braided cover with stainless braided core, coated with a neoprene inner lining. Kits ship complete with black anodised hose clamps. 614004* 6 ft 210 Oil Line Kit����������������������������������������������������������������������$78.99 614005** 12ft 210 Oil Line Kit ������������������������������������������������������������������$142.99 614006 210 Black Braided Oil Hose, 6ft ������������������������������������������������$47.99 614007 210 Black Braided Oil Hose, 12ft ����������������������������������������������$99.99 614008 3/8” Black Hose Finishers - 6 Pak ����������������������������������������������$31.99 614009 3/8” Black Hose Finishers - 10 Pak��������������������������������������������$47.99 *Contains 6 ft of 210 hose and 4ea Black Hose Finishers **Contains 12 ft of 210 hose and 8ea Black Hose Finishers

12427

Overhead Rocker Arm Oil Lines

Set of two stainless steel braided oil lines with chrome NPT fittings. 12427 Fits 66-84 Shovelheads����������������������������������������������������������������$15.99 12428 Fits 57-85 Sportster models��������������������������������������������������������$16.99

28015

28016

Goodridge Custom Stainless Steel Oil Line and Fittings

Custom oil lines are made simple with Goodridge’s new do-it-yourself reusable oil line components. This new system utilizes the same chrome steel fittings Goodridge is known for, but in a user-friendly format that allows you to make your own kit. These ground breaking fittings are coupled with their stainless steel braided PTFE lined hose and can be used to assemble oil line kits for virtually any Big Twin on the road. 610250 12Ft roll –6 stainless Teflon hose��������������������������������������������$107.99 610251 Chrome oil tank stub fitting������������������������������������������������������$40.99 610252 Chrome straight oil fitting 1/8 NPT������������������������������������������$30.99 610254 Chrome 90 degree oil fitting 1/8 NPT��������������������������������������$37.99

SHEET.26

Chrome Rocker Oil Lines

Chromed rocker box oil lines for Sportster models and Shovelheads. Includes complete set of fittings and seals (2 lines). 28015 Fits Shovelheads 66-84 (repl. OEMs 62783-66A, 62785-66A)

����������������������������������������������������������������������������������������������������������$13.99

28016

Fits Sportster models (except magneto models) from 57-85 (repl. OEM 17324-57A)����������������������������������������������������������������$13.99

Rocker Box Oil Line Fittings Includes chrome fittings and seals for the rocker box oil lines on all Sportster models and Shovelheads 57-85. 010421 Sold in pairs (repl. OEMs 63527-57A, 63526-57)����������������������$5.99 12074 Motor Factory oil line sleeves ONLY (repl. OEM 63529-57) pack of 10��������������������������������������������������������������������������������������������������$0.25

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.

Please see Cautionary Information in back of catalog.

SHEETMETAL General Warnings. Motorcycle riding is a dangerous activity. The only way to be sure to avoid injury is not to ride! Even if you use the finest and best-maintained equipment, wear a helmet and protective clothing, and take all possible precautions, it is not possible to avoid every risk. Motorcycle accidents frequently result in serious injury, including death. Please do not operate a motorcycle or other motor vehicle when you are tired or under the influence of alcohol or drugs, or when your perception is impaired for any other reason. At all times, please wear a helmet, ride carefully and within posted speed limits, and obey all other traffic regulations and instructions from law enforcement personnel. Custom Chrome, sells aftermarket motorcycle parts for Harley-Davidson® and other brands. If you do not have the necessary experience and skill, please have a qualified mechanic install any new or replacement part on your motorcycle. The failure to install properly and test any new or replacement component could adversely affect your motorcycle’s operation and result in an accident, including a fatal accident. Federal and state laws and regulations impose restrictions on modifying the engine, ignition, exhaust and other components of a motorcycle intended for on-road use. In addition, these laws and regulations impose requirements on windshields, brake components, lighting, and other equipment on your motorcycle. Accordingly, certain parts in this catalog are for competition or display purposes only. In general, those parts are indicated by a “Competition” mark: a checkered flag in a yellow oval. If you are a retail customer, you are responsible to know the laws and regulations that govern the modification of your motorcycle. Custom Chrome is not responsible if you modify your motorcycle or any component in violation of law. If you have any questions regarding a particular component, please consult your dealer or a qualified motorcycle mechanic. The following is additional information relating to components for sale in various sections of this catalog. This information is not exclusive – if you have any questions regarding the installation or use of any component, please contact your dealer, a qualified mechanic, or Custom Chrome’s customer service department.

These fine Jammer products are found in the 2014 Custom Chrome Catalog

Use the Dealer Locator at customchrome.com to find your local Custom Chrome Dealer

This symbol appearing throughout our catalog means that the specified items are high-performance exhaust, carburetor, ignition, or engine components and are not legal for use on pollution or noise-controlled vehicles (except in organized and sanctioned racing or competition events). It is a violation of federal law and the law in every state to install or use any of these components on motorcycles that are licensed for street use or used on public roads. Penalties are substantial. CCI offers these components solely for competition, display, or other off-road use, and is not responsible for any illegal application or use thereof.

© COPYRIGHT 1982-2014 BY CUSTOM CHROME - A DIVISION OF DAE-IL USA, INC. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS; ELECTRONIC, MECHANICAL, PHOTOCOPYING, RECORDING, OR OTHERWISE WITHOUT PRIOR WRITTEN PERMISSION OF THE PUBLISHER.

w w w.cu sto m c h ro m e.co m

SHEET.27

155 East Main Ave. | Suite 150 | Morgan Hill, CA 95037