Setting Adjustments

SRIXON Series Instruction Manual / Setting Adjustments CLEVELAND GOLF / SRIXON 5601 Skylab Rd., Huntington Beach, CA 92647, U.S.A. Tel:1-714-889-13...
Author: Winifred Golden
7 downloads 0 Views 1MB Size
SRIXON

Series

Instruction Manual / Setting Adjustments

CLEVELAND GOLF / SRIXON 5601 Skylab Rd., Huntington Beach, CA 92647, U.S.A. Tel:1-714-889-1300 Fax:1-714-889-5890

CLEVELAND GOLF / SRIXON CANADA 19099 25th Ave, #104 Surrey, BC, V3S 3V2, Canada Tel:1-604-542-0911 Fax:1-604-542-0955

Part names and features How to remove and install the QTS sleeve (torque wrench operation) How to remove and install the QTS sleeve (sleeve installation) How to change tuning weights QTS sleeve performance guide QTS sleeve position overview Tuning weight performance guide Important Precautions—Please Read!

P01 P03 P05 P07 P09 P11 P13 P15

Part names and features

745 Driver 945 Driver F45 Fairway wood

Accessories

01

Tuning weight

Tuning weight

Change weights for fine adjustment of Center of Gravity (CG) height

Change weights for fine adjustment of CG depth and height

QTS sleeve

QTS sleeve

Change position to set desired face angle, lie angle, and loft angle

Change position to set desired face angle, lie angle, and loft angle

Weight port (center)

Weight port (back)

545 Driver Custom torque wrench

Custom pouch

Use only the torque wrench and tuning weights provided. Use of damaged or improperly installed tuning weights may result in injury or product damage. 02

How to install and remove the QTS sleeve

1

Hold the club upright with the grip resting on the ground. Use this position when loosening and tightening.

2

Supporting the head in your hand, gently insert the torque wrench into the screw hole.

(Torque wrench operation) Tighten 3 Loosen 4 With With the torque wrench aligned the torque wrench aligned with the shaft, turn it counterclockwise.

with the shaft, turn it clockwise until you hear a 'click'.

Click

Shaft and torque wrench should form a straight line

* Be careful not to loosen the screw too much, as you may drop the screw and lose the washer.

Do not use any tool other than the supplied torque wrench. Also do not use the supplied torque wrench on any other products.

Always tighten until you hear a 'click'.

Damaged QTS sleeve and/or improperly installed QTS sleeve may result in injury or product damage. * Not compatible with SRIXON Z-STAR series torque wrenches.

Once you hear a 'click', stop tightening.

Position the torque wrench so that it is correctly aligned with the shaft.

Screws fastening the QTS sleeve employed on the driver and fairway woods are designed for respective specifications and are not interchangeable.

Failure to insert the tip of the torque wrench firmly into the screw hole may result in damage to the screw.

03

Improperly aligned torque wrench

Failure to tighten until you hear a 'click' may result in separation of the club head or product damage. Over-tightening may damage the QTS sleeve.

04

How to remove and install the QTS sleeve

5 Insert the shaft into the head Align the position line with the ★ mark and press straight in. * Illustration shows neutral position

(Sleeve installation)

6 Insertion sample For right position

For left position

Align the ★ mark on the head with the 'R' on the QTS sleeve and press straight in.

Align the ★ mark on the head with the 'L' on the QTS sleeve and press straight in.

The shaft may not insert fully if the position line and sleeve mark are not correctly aligned. Press the shaft all the way in until the QTS sleeve is completely covered.

05

06

How to change tuning weights Locked mark on weight aligned with “LOCK ” mark on head

1

Unlocked, ready for removal mark on weight aligned with “ UNLOCK” mark on head

Pull the torque wrench directly up to remove the weight. * If the weight is difficult to remove even with the mark on the weight aligned with the “ UNLOCK” mark on the head, lightly jiggle and pull the tuning weight at the same time with torque wrench still inserted.

3

Fix the desired tuning weight on the tip of the custom torque wrench, insert it into the weight port, and rotate it 45˚ clockwise to the “LOCK ” position to lock it. * Do not turn the tuning weight past the locked position.

Hold the clubhead securely in one hand and the custom torque wrench in the other. Insert the custom torque wrench straight into the hole in the center of the tuning weight and rotate it 45˚ counterclockwise to the “ UNLOCK” position to unlock it.

Do not use any tool other than the supplied torque wrench. Also do not use the supplied torque wrench on any other products.

Do not turn the tuning weight past the unlocked position.

Improper installation of the tuning weight may result in injury or product damage.

Do not rotate more than 45˚.

Ensure that the tip of the custom torque wrench is fully inserted into the hole of the tuning weight. Hold both the custom torque wrench and the clubhead securely while exchanging the weights.

07

2

Improper installation of the tuning weight may result in injury or product damage. When installing or removing the tuning weights, rotate them only 45˚ until they reach the “LOCK ” or “ UNLOCK” position respectively. Do not attempt to turn the weight more than 45˚, as it may damage either the tuning weight or the weight port.

08

QTS sleeve performance guide Select from 12 different positions to set your preferred face angle, lie angle, and loft angle.

The sleeve is set to N (Neutral) at time of purchase. Refer to the guide to set your preferred trajectory.

Lateral range of adjustment depending on sleeve position Flight path can be adjusted laterally by approx. 37 yards (W#1) 10

11

7

2

3

High trajectory 12

8

6

1

Low trajectory

9

4

5

Approx. 37 yards Draw

09

Fade

10

QTS sleeve position overview 1

Initial

2

3

4

5

6

7

8

9

10

11

12

Position Face positioning Lie angle

11

N Neutral

R Right

NU Neutral Upright

L Left

Straight face

Open face

Straight face

Closed face

Standard

Moderate upright

Upright

Moderate upright

0

0

-2.0

+1.0

0

+2.0

+2.0

+1.0

12

Tuning weight performance guide 745 Driver 945 Driver F45 Fairway wood

545 Driver Weight port (center) Weight port (back)

Lowering the trajectory (when ball tends to rise)

Raising the trajectory (when ball tends to drop)

Lowering the trajectory (when ball tends to rise)

Raising the trajectory (when ball tends to drop)

A strong trajectory when hitting into the wind and more distance with a run.

A high trajectory that delivers distance with longer carry.

A strong trajectory when hitting into the wind and more distance with a run.

A high trajectory that delivers distance with longer carry.

Heavy

Installing a heavy weight lowers the CG to deliver a low-spin trajectory.

Trajectory—initial settingg

13

TTrajectory after tuningg

Light

Installing a light weight raises the CG to achieve the appropriate amount of spin.

Trajectory—initial settingg

TTrajectory after tuningg

Light

Installing a light weight on the back side creates a shallower CG which reduces spin.

Trajectory—initial settingg

TTrajectory after tuningg

Heavy

Installing a heavy weight on the back side creates a deeper CG that increases spin appropriately.

Trajectory—initial settingg

TTrajectory after tuningg

14

Important To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions. Precautions Be sure to read the Important Precautions carefully and exercise appropriate care. The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein. Before using

Rules of Golf

Carefully inspect the QTS sleeve and tuning weights prior to each round of golf or practice session to confirm that they are properly secured.

You may not change the QTS sleeve position or exchange weights during a round.

1

Check to see that the tuning weights are locked securely in position. If the tuning weights are not secured firmly in the weight port and you swing the club during a game or practice session, there is a danger that a weight could fly off, injuring either you or a bystander.

SRIXON Z Series clubs conform with R&A-approved Rules of Golf. However, it is against the rules to modify club performance during a round by changing the QTS sleeve position or exchanging weights to change the CG position, as this breaches the Rules of Golf regulation 4-2a, which states: “During a stipulated round, the playing characteristics of a club must not be purposely changed by adjustment or by any other means.”

2

Confirm the weight is locked in position Unlocked, ready for removal mark on weight aligned with “LOCK ” mark on head

15

mark on weight aligned with “ UNLOCK” mark on head

Check to see that the QTS sleeve is properly secured. Tighten the sleeve until you hear a 'click'. If you fail to properly secure the sleeve, there is a possibility that the head may come off in mid swing, injuring either you or a bystander.

16

Important To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions. Precautions Be sure to read the Important Precautions carefully and exercise appropriate care. The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein. Care and storage

17

1

Only remove the QTS sleeve or tuning weights when making adjustments. All parts should remain properly installed at all other times, including when the club is in storage, to ensure that no foreign objects or debris become lodged in the sleeve connection or screw holes.

2

When removing the QTS sleeve or tuning weights, be sure that you do so in a clean location to ensure that no foreign objects or debris become lodged inside. Installing the tuning weight while there are foreign objects or debris in the weight port may damage either the weight or the port, or prevent proper installation or removal of the tuning weight. It may even cause internal damage to the club head, adversely affecting club performance.

3

If the QTS sleeve or weight ports become soiled with water, dirt, or other debris, wipe them clean with a cotton swab or a soft, clean cloth.

4

Do not heat the QTS sleeve as it may damage the product.

5

Avoid adjusting the QTS sleeve or changing weights when the temperature is below -5˚C or above 45˚C, as it may damage the plastic components in the weight port.

6

Please be aware that attempts to remove the QTS sleeve or intentionally disassembling it may not comply with the manufacturer’s warranty. * For information on manufacturer's warranty regulations, please refer to the owner's manual and warranty included with your golf club. 18