SERVICE

Whirlpool Europe Customer Services

ADP 4300 WH

Service Manual Dishwasher ADP 4300 WH Model Version

ADP 4300 WH 8511 764 43810

Page

Technical data

2-4

Spare part list

5-6

Exploded view

7-8

Circuit diagram

9

Program diagram

10

Text/Legend

11 - 16

Family

WRC - IC LOW 3

This documentation is only intended for qualified technicians who are aware of the respective safety regulations. Date: 19.07.2005 Subject to modification Document-No.: 4812 728 11578

19.07.2005 / Page 2 Doc. No: 4812 728 11578

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE

Technical data Dimension Height Width Depth Weight

82.0 - 87.0cm 59.7 cm 55.5 cm 50 kg

Wooden door for Integrable types Thickness min. Thickness max. Width min. Width max. Height min. Height max. Weight max. Max. stick out over lower edge of appliance door Height of plinth min.

16 20 592 595 515 600 5.5

mm mm mm mm mm mm kg

92 93

mm mm

Water Volume at permanent spray system Water Regeneration Back rinse 3x Prewash Main wash Intermediate rinse 1 Intermediate rinse 2 Clear rinse Safety/ overflow

Volume 0.3 l 1.0 l 4.8 l 4.2 l 4.2 l 4.2 l 4.2 l 8.5 l

Level 15 mm 60 mm 120 mm 118 mm 118 mm 118 mm 118 mm 141 mm

Measuring the level Remove the coarse sieve, put in a measuring meter into the sump, measure the hight of the water level.

Electronic boards Service boards see spare part list Serial boards see on the boards itself Programmed control board and programing of version , see „Board Service“ and „DATA“ on rating plate of inner door: UCB 704812 Data set 704802 Basic UCB, not programmed see on the board itself 4619 727 04651 Succession of programs Programs Succession

Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program.

see program diagram P3a-P5b-P7a

Detergent max. Pre-wash Main-wash Rinse aid 6 Dosage steps

10 40 135 1-6

cm3 cm3 cm3 ml

2 700 300

kg cm3 cm3

0.3 - 10 0.3

bar bar

2800 3000 30 - 40 30 - 40

RPM RPM RPM RPM

Water softener Saltcontainer Resin container Regeneration dosage Water pressure

Datas Energy Label Reference program Energy Performance Cleaning Performance Drying Performance

P5b B B C

Program information Start indicator All programs will be locked after start. Changing the program or finishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position.

Inlet pressure Spray pump pressure Rotations Spray pump motor Drain pump motor Spray arm lower Spray arm upper

SERVICE

Whirlpool Europe Customer Service

ADP 4300 WH 8511 764 43810

19.07.2005 / Page 3 Doc. No: 4812 728 11578

Technical data Flow rates/ Inlet volume

Regenerating valve

Flow meter (at 0.3 bar = quantity 1.1 l/min) 208 lmp/l Spray pump 65 l/min Drain pump 16 l/min Pump height max. 1.1 m Inlet valve 4 l/min Spray arm lower ~ 33 l/min Sprayarm upper ~ 27 l/min Sprayarm/ Shower top ~8 l/min

220/ 240 50 2.0 - 2.2 10

V Hz kW A

Spray pump motor - permanent spray system Voltage Power consumption Frequency Resistance

220/ 240 80 50 30

V W Hz Ω

Drain pump motor Voltage Power consumption Resistance

220/ 240 V 30 W 146 Ω

220/ 240 1.87/ 2.04 24.5 ~ 2.0 ~ 115

V kW Ω ˚C/min ˚C

~ 85 206

˚C ˚C

Electronic aqua control

Single electric water inlet valve Voltage Frequency Resistance

Voltage Frequency Resistance

220/ 240 V 50/ 60 Hz 1.3 kΩ

flow meter NTC 20 ˚C 25 ˚C 30 ˚C 40 ˚C 50 ˚C 60 ˚C 70 ˚C 80 ˚C 85 ˚C

58.1 47.1 38.2 25.4 17.2 11.8 8.3 6 4

kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ

Volume

300

cm3

after wash cycles

depending on the water softener setting 0 - 40 ˚dh 0 - 10.7 mmol/l 0 - 107 ˚Fh

water hardness

Water safty options Waterstop system

Coil of dispenser

Regeneration

Heating - 1 Element system Voltage Power consumption Resistance Heating speed Temperature on surface Safety thermostat self reset (Temperature of water) Fuse

220/ 240 V 50/ 60 Hz 3.13 kΩ

Reed contacts

Electrical base data Voltage Frequency Total power Fuse

Voltage Frequency Resistance

220/ 240 V 50/ 60 Hz 3.76 kΩ

Salt consumption for regeneration

~ 77

Number of cycles with 2 kg salt

~ 26

g

19.07.2005 / Page 4 Doc. No: 4812 728 11578

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE

Technical data Water softener setting To change the water softener setting: • Push the POWER button on • Change to program 2 • Hold the START button for 5 seconds until the LED is flashing • Water softener setting is shown by flashing LED • By pushing the START button you can change the setting • Push the POWER button off to save and exit the water softener setting Water hardness 1 soft 1 - 2 soft/ medium 2 medium 3 medium/ hard 4 hard 4 very hard 4 extremely hard

German degrees ˚dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60

French degrees ˚fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107

English degrees Clarke ˚e 0 - 6,3 7 - 12.6 13.3 - 18.9 19.6 - 25.9 26.6 - 35 35.7 - 44.1 44.8 - 74.9

mmol/l 0 - 0.9 1 - 1.8 1.9 - 2.7 2.8 - 3.7 3.8 - 5.0 5.1 - 6.3 6.4 - 10.7

Water softener setting is shown by flashing LED 1x 2x 3x 4 x (DEFAULT SETTING) 5x 6x 7x

Accesory If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. For higher mounted Dishwashers to prevent the drain off effect - also usable for lower drain pipes and to prevent the failure F8 use Kit 4812 310 18993.

SERVICE

Whirlpool Europe Customer Service

ADP4300WH 8511 764 43810

19.07.2005 / Page 5 Doc. No: 4812 728 11578

Spare part list Model Service No. Version

ADP 4300 WH 851176443810 851176443810

Pos. No. 12NC Code

Description

Pos. No. 12NC Code

Description

003 0 004 0 004 1 011 0 022 0

4812 440 19594 4812 440 18952 4812 401 18402 4812 505 18357 4812 440 10755

Traverse Drip tray assy Holder Foot short Side panel left

490 0 490 1 521 0 521 8 571 0

4819 321 18136 4812 321 28367 4812 218 38218 4812 530 78066 4812 281 28379

Cable,mains 2m SA Strain relief User board (UCB) Axle program knob grey Valve inlet

022 1 024 0 024 5 030 0 034 0

4812 440 10754 4812 440 10417 4812 440 10944 4812 310 18916 4812 404 78237

Side panel right Panel, rear Damper fix Motor synch Table top cpl. WH Spacer

575 0 583 0 621 0 633 0 680 0

4812 281 28361 4812 271 28407 4819 410 29004 4812 271 38355 4812 418 68332

Regen.valve Switch diaphragm Switch ON/OFF Microswitch door Combidosage cpl.

040 1 040 2 040 3 044 0 047 0

4812 417 18774 4812 417 18773 4812 417 19172 4812 492 38358 4812 404 48746

Hinge left Hinge right Protector f.door (set) Spring f.door Brake f.door

680 1 681 1 681 2 682 0 691 0

4812 466 68495 4812 466 68497 4812 440 18975 4812 466 68496 4812 282 68035

Gasket Gasket Flap Gasket Feeler NTC

047 1 047 2 053 0 061 0 103 0

4812 401 18397 4812 404 68023 4812 440 89031 4812 466 88672 4812 440 10758

Band,brake Hook Plinth WH Counter weight Door outer

701 0 701 1 701 2 710 0 710 2

4812 530 28081 4812 310 18302 4822 480 50159 4812 418 68149 4812 310 38896

Hose, inlet 3/8Z cpl. 5m Yoke Sieve inlet Monoblock Threaded ring

120 0 120 1 130 0 131 0 191 0

4812 440 19456 4812 440 18969 4812 417 58373 4812 401 18416 4812 466 68564

Door,inner Batten Tilt lock cpl. bk Hook lock Gasket door

710 3 714 0 716 0 716 1 716 2

4819 466 69562 4812 462 79906 4812 418 68147 4812 466 68475 4812 462 78994

Gasket set Threaded cap saph Reg.dosage with flowmeter Gasket Cover

192 0 241 0 241 1 241 3 241 8

4812 466 68467 4812 458 19027 4812 458 18324 4812 528 88068 4812 466 68553

Gasket, door lower Basket upper straight Holder cups right wh Wheel,basket upper (set) Spacer cap set

717 1 721 1 722 0 722 2 723 0

4812 462 79793 4812 360 68689 4812 360 68687 4812 360 68693 4812 360 68691

Stopper Spray arm lower. cpl. sa Spray arm upper sa Spray arm 2nd level cpl. saph Douche ceiling

241 9 242 0 242 1 242 4 243 0

4812 528 88101 4812 310 28134 4812 528 88069 4812 466 48091 4812 458 18272

Wheel,basket basket upper Basket lower KIT Wheel,basket lower wh Fixation grey Basket cutlery

726 1 726 2 743 1 751 0 755 0

4812 530 29331 4812 505 18208 4812 530 28102 4812 418 18338 4812 530 29119

Tube assembly cpl.saph Nut Hose, inlet Water collector Bend

261 0 261 1 261 2 263 0 263 1

4812 462 79831 4812 462 79768 4812 310 18972 4819 520 18013 4812 310 48026

Rail telescope, inner Cap rail rear Cap rail front Ball cage cpl. Service kit balls plastic

755 2 761 0 761 2 761 3 761 4

4812 530 48148 4812 480 58122 4812 418 18337 4812 418 18341 4812 530 58141

Tray,leak Sieve fine Cover sieve Cover O-Ring

301 0 301 1 303 1 331 0 332 0

4812 453 72769 4812 452 79742 4812 460 38148 4812 413 59155 4812 410 29163

Control panel ADP 4300 WH Nameplate Whirlpool Plate,handle Knob program cpl. WH Button Start

763 0 781 0 781 3 783 4 783 6

4812 480 58123 4812 530 29113 4812 281 28417 4812 530 28888 4812 530 28796

Sieve coarse Hose,draining Flap non-return Hose Hose 10x3x180+10

332 3 350 2 400 0 400 1 421 0

4812 410 29166 4812 381 28068 4812 361 58334 4812 466 68776 4812 121 18158

Button ON/OFF WH Light guide Motor +SP,50Hz,per.HP-PNT Spacer support motor/sp Interf.filter

791 0 791 2 791 4 791 5 901 0

4812 532 68099 4812 530 58093 4812 466 68503 4812 466 68504 4822 401 10258

Gasket Gasket Gasket Gasket Clamp,hose 10-18 mm

430 0 430 1 450 0 480 0 480 3

4812 360 18508 4812 466 68689 4812 259 28684 4812 321 28424 4812 401 18418

Pump,draining cpl. Gasket Heating element Cable harness (EBL) without LS6 Protector f.wiring

901 1 901 2 901 5 904 0 904 3

4812 401 18424 4812 401 18157 4812 401 48573 4812 462 78998 4812 462 79636

Strap 050,0 Strap 32-50/9 C61 Strap 028,6 Threaded cap Cover WH 3,5x4

19.07.2005 / Page 6 Doc. No: 4812 728 11578

ADP4300WH 8511 764 43810

Spare part list Model Service No. Version

ADP 4300 WH 851176443810 851176443810

Pos. No. 12NC Code

Description

910 1 910 2 910 3 910 4 910 5

4812 502 18394 4812 502 18363 4812 502 18527 4812 502 18385 4812 502 18393

Screw 3,5x14-H Screw 4,0x12-H Screw 4x15 T20 Screw M3,5x8-T15M Screw 3,5x9-1 Tx15

910 7 910 8 910 9 964 0 964 1

4812 502 18397 4812 502 18389 4812 401 18425 4812 466 68536 4812 466 68469

Screw INOX A2 M 5X12 Screw 5x20 T20 Screw 2,5x18-H Gasket housing ri/le Gasket housing upper

993 0 993 5

4819 530 29028 4822 532 80216

Bow Funnel salt

Whirlpool Europe Customer Service

SERVICE

SERVICE Exploded view

Whirlpool Europe Customer Service

ADP 4300 WH 8511 764 43810

19.07.2005 / Page 7 Doc. No: 4812 728 11578

19.07.2005 / Page 8 Doc. No: 4812 728 11578

Exploded view

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE

Capacitor Timerswitch Delay Drain pump motor Cleaning agent dosage Final rinse dosage Door switch Flow meter Heating Interference filter Line Water leakage switch Main switch Thermostat temp. sensor Neutral Plug to program Relay Heating Relay Spray pump motor Reed relay salt Reed relay rinsaid Sprayarm motor Safety thermostat Fuse Power supply terminal Winding protective contact User- and Control board Fan ventilator Water inlet valve Water regenerating valve Water indicator

black blue grey white

00 66 88 99

Multi-tablet Micro switch (3in1)

3in1 C1 DLB DPM DD DR DS FM HEW IF L LS6 MS NTC N PRG RE2 RE3 RR SA RR RA SPM THS1 THS 2 TBL TL UCB VM WV1 WV2 WI

SERVICE Whirlpool Europe Customer Service ADP 4300 WH 8511 764 43810 19.07.2005 / Page 9 Doc. No: 4812 728 11578

Circuit diagram

19.07.2005 / Page 10 Doc. No: 4812 728 11578

Program diagram

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE

SERVICE Text/Legend

Whirlpool Europe Customer Service

ADP 4300 WH 8511 764 43810

19.07.2005 / Page 11 Doc. No: 4812 728 11578

19.07.2005 / Page 12 Doc. No: 4812 728 11578

Text/Legend

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE

SERVICE Text/Legend

Whirlpool Europe Customer Service

ADP 4300 WH 8511 764 43810

19.07.2005 / Page 13 Doc. No: 4812 728 11578

19.07.2005 / Page 14 Doc. No: 4812 728 11578

Text/Legend

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE

SERVICE Text/Legend

Whirlpool Europe Customer Service

ADP 4300 WH 8511 764 43810

19.07.2005 / Page 15 Doc. No: 4812 728 11578

19.07.2005 / Page 16 Doc. No: 4812 728 11578

Text/Legend

ADP 4300 WH 8511 764 43810

Whirlpool Europe Customer Service

SERVICE