071900
Russell Haven of Rest Funeral Home SECTION 10160 SOLID PLASTIC TOILET PARTITIONS
PART 1 - GENERAL 1.1
Related Documents: The General Provisions of the Contract, including the General Conditions, Supplementary Conditions and Special Conditions (if any), along with the General Requirements, apply to the work specified in this Section.
1.3
Scope:
1.4
A.
Provide all labor, materials, etc., necessary for the completion of the work of this Section as specified or shown on the Drawings.
B.
Work of this Section consists of, but is not limited to the following: 1. Toilet stalls, stall doors and urinal screens . 2. Hardware, etc. for stalls. 3. Shop Drawings. 4. Warranties.
Submittals: A.
Comply with Section 01300, Submittals.
B.
Provide Drawings showing proper securement of the finished work.
C.
Furnish color cards, for use of the Architect, for color selection.
PART 2 - PRODUCTS 2.1
2.2
Acceptable Manufacturers: A.
Santana Solid Plastic Products
B.
No "approved equal" material or equipment will be considered unless written request has been submitted to the Architect for approval.
Materials: A.
Toilet partitions shall be floor-mounted, overhead braced, with non-corrosive panels, doors and pilaster similar and equal to Poly-mar HD partitions as manufactured by 10160-1
Rev. 10/08
071900
Russell Haven of Rest Funeral Home Santana Solid Plastic Products, Scanton, PA or comparable products with hardware as specified herein.
B.
Panels, doors and pilasters shall be fabricated from polymer resins under high pressure forming a single component section which is waterproof, non-absorbent and has a selflubricating surface that resists marking with pens, pencils or other writing utensils. All panels, doors and pilasters to arrive at job site with special protective plastic covering.
C.
Construction: 1. Single component construction of solid Poly-Mar HD in colors that extend from the surface throughout the entire thickness of the panels, doors and pilasters. 2. Doors, panels and pilasters shall be 1" thick and all edges machined to a radius of .250" and all exposed edges to be free of saw marks. 3. Dividing panels shall be 55" high and mounted at 14" above finished floor. Aluminum edging strips shall be fastened to the bottom edge of all panels full length. 4. Doors shall be 55" high and mounted at 14" above finished floor. Aluminum edging strips shall be fastened to the bottom edge of all doors full width. 5. Pilasters shall be 82" high and fastened to 3" high non-corrosive polymer resin shoes with theft-proof fastening bolts. 6. Finish of doors, panels and pilasters shall be similar and equal to Santana Products, Inc. "Plasti-Glaze 280". Color to be selected from manufacturer's standard colors.
D.
Hardware: Door hardware shall be as follows: 1. Hinges shall be fabricated from heavy aluminum extrusion stock (6463-T5 Alloy) with clear, anodized finish, wrap- around flanges, surface-mounted and throughbolted to doors and pilasters with one-way fastening bolts. Hinges will be factoryset to a full close position unless otherwise noted, 8" heavy-duty hinges shall be used throughout. 2. Each door shall be furnished with (1) coat hook/bumper of heavy chrome-plated Zamak with rubber bumper. (Handicapped doors also include: (1) door pull and (1) wall stop). 3. Door strike and keeper shall be fabricated from heavy aluminum extrusion stock (6463-T5 Alloy) with clear, anodized finish, wrap-around flanges, surface-mounted and through-bolted to pilaster with one-way fastening bolts. Strike shall be heavyduty 6" strike plates. 4. Door latch housing shall be fabricated from heavy aluminum extrusion stock (6463-T5 Alloy) with clear, anodized finish, surface-mounted and through-bolted to door with one-way fastening bolts. Slide bolt and button shall be heavy aluminum with "Tough-Coat" Black finish. Provide hook and eye hold-open at bottom of all doors: eye secured to door, hook secured to masonry wherever possible. 10160-2
Rev. 10/08
071900
Russell Haven of Rest Funeral Home
E.
Pilaster shoes shall be made from Polymer resin formed under high pressure and be made of single construction with color throughout. Pilaster shoes shall be anchored to finish floor with No. 5 Plastic Anchors and No. 14 stainless steel phillips head screws.
F.
Full length continuous wall brackets shall be made from polymer resin formed under high pressure and be made of single construction with color throughout. Solid plastic continuous wall bracket weighing not less than .83 pounds per linear foot similar or equal to Santana Solid Plastic Products, shall be used for all panels to pilaster to wall and panel to wall connections. Wall brackets shall be pre-drilled by manufacturer with holes spaced every 6" along full length of brackets. Wall brackets shall be throughbolted to panels and pilasters with one-way fastening bolts. Attachment of brackets to adjacent wall construction shall be accomplished by (1) theft-proof Zamac mushroom nail in head anchor directly behind the vertical edge of panels and pilasters at every 12" along the full length of bracket and (2) No. 5 plastic anchors and No. 14 x 1-1/4" stainless steel phillips head screws at each 12" interval alternately spaced between anchor connections.
G.
Headrail shall be heavy of aluminum extrusion stock (6463-T5 Alloy) with mill finish in anti-grip configuration weighing not less than 1.188 pounds per linear foot, similar and equal to Santana Solid Plastic Products, Section #58993. Headrail shall be fastened to tops of pilasters and headrail brackets by through-bolting with one-way fastening bolts.
H.
Headrail brackets shall be 16 gauge stainless steel.
PART 3 - EXECUTION 3.1
Installation: Erection of partitions, etc., shall be in accordance with the manufacturer's standard recommendations and the following: A.
All parts shall be erected in substantial manner, straight, level, and plumb.
B.
No evidence of drilling, cutting or patching shall be visible in the finished work.
C.
Clearance at vertical edges of doors shall be uniform top to bottom and shall not exceed 3/16".
D.
Finished surfaces shall be cleaned after installation and left free of imperfections.
END OF SECTION 10160
10160-3
Rev. 10/08
071900
Russell Haven of Rest Funeral Home SECTION 10350 FLAGPOLE
PART 1 - EXECUTION 1.1
Related Documents: The General Provisions of the Contract, including the General Conditions, Supplementary Conditions and Special Conditions (if any), along with the General Requirements, apply to the work specified in this Section.
1.2
Scope: Provide and install one aluminum flagpole with necessary concrete footing, lightning grounding and Internal halyard, with American flag. install at location shown in the plans.
1.3
Quality Assurance: Deliver to site in protective covering to protect finishes. Provide manufacturer's warranty.
1.4
Shop Drawings: Submit Shop Drawings which indicate foundation collar, finishes, size, material of pole and flag for approval by the Architect.
PART 2 - PRODUCTS 2.1
2.2
Acceptable Manufacturers: A.
American Flagpole, P.O.Box 547, Hillman Highway, Abingdou, Virginia.
B.
Concord Industries, 4150 A. Kellway Circle, Addison, Texas.
C.
Pole-Tec Co.,Inc. 97 Gnarled Hollow Road, E. Setauket, New York
Product Requirements: A.
Height: 30' exposed height.
B.
Wall Thickness: .188 aluminum.
C.
Sections: Single piece.
D.
Butt Diameter: 6"
E.
Flag Size: Furnish High Quality Dacron, 6' x 10' American Flag.
F.
Finial: Gold anodized sphere.
G.
Halyard: 5/16' braided rope 10350-1
Rev. 10/08
071900
2.3
Russell Haven of Rest Funeral Home
H.
Cleat: 9" cast aluminum 4'-6" above grade.
I.
Base: Flashing Collar.
J.
Foundation Sleeve: 16ga. Galvanized Steel with ground spike.
Design Criteria: A.
Wind Loading: 75 MPH with 5' x 8' flag flying.
B.
Material: 6063 T6 aluminum alloy, seamless.
C.
Taper: Uniform straight line.
D.
Finish: Anodized Aluminum.
PART 3 - EXECUTION 3.1
Installation: Flagpole shall be installed at location shown on the Drawings by experienced erection crew according to manufacturer's suggested procedure and detail on Drawings.
END OF SECTION 10350
10350-2
Rev. 10/08
071900
Russell Haven of Rest Funeral Home SECTION 10355 PREFAB FIREPLACE
PART 1 - EXECUTION 1.1
Related Documents: The General Provisions of the Contract, including the General Conditions, Supplementary Conditions and Special Conditions (if any), along with the General Requirements, apply to the work specified in this Section.
1.2
Scope: Provide and install one 42" prefab fireplace with gas log ,glass door enclosure remote control and all necessary chimney accessories required for complete installation.
1.3
Quality Assurance: Deliver to site in protective covering to protect finishes. Provide manufacturer's warranty.
1.4
Shop Drawings: Submit Shop Drawings which indicate size, finishes, size, material and accessories required .
PART 2 - PRODUCTS 2.1
Acceptable Manufacturers: A.
Majestic Fireplaces , www.majesticproducts.com
2.2
Product Requirements:
A.
Model: BV 5142
B.
Ignition System: Electronic for L.P. gas log
C.
Firebrick: Cottage Red.
D.
Glass Doors: Bifold with Polished brass frame
E.
Remote Control: Furnish battery operated remote.
F.
Gas Log: Gold anodized sphere.
G.
Chimney Cap: LFSQT Termination Shroud.
H.
Chimney: 8" double walled metal chimney pipe as required.
10350-1
Rev. 10/08
071900
Russell Haven of Rest Funeral Home
PART 3 - EXECUTION 3.1
Installation: Fireplace shall be installed according to manufacturers instructions and according to the Florida Building Code. Provide all accessories for complete operable installation and coordinate with construction of brick hearth , decorative wood mantle and custom chimney cap.
END OF SECTION 10350
10350-2
Rev. 10/08
071900
Russell Haven of Rest Funeral Home SECTION 10355 PREFAB FIREPLACE
PART 1 - EXECUTION 1.1
Related Documents: The General Provisions of the Contract, including the General Conditions, Supplementary Conditions and Special Conditions (if any), along with the General Requirements, apply to the work specified in this Section.
1.2
Scope: Provide and install one 42" prefab fireplace with gas log ,glass door enclosure remote control and all necessary chimney accessories required for complete installation.
1.3
Quality Assurance: Deliver to site in protective covering to protect finishes. Provide manufacturer's warranty.
1.4
Shop Drawings: Submit Shop Drawings which indicate size, finishes, size, material and accessories required .
PART 2 - PRODUCTS 2.1
Acceptable Manufacturers: A.
Majestic Fireplaces , www.majesticproducts.com
2.2
Product Requirements:
A.
Model: BV 5142
B.
Ignition System: Electronic for L.P. gas log
C.
Firebrick: Cottage Red.
D.
Glass Doors: Bifold with Polished brass frame
E.
Remote Control: Furnish battery operated remote.
F.
Gas Log: Gold anodized sphere.
G.
Chimney Cap: LFSQT Termination Shroud.
H.
Chimney: 8" double walled metal chimney pipe as required.
10350-1
Rev. 10/08
071900
Russell Haven of Rest Funeral Home
PART 3 - EXECUTION 3.1
Installation: Fireplace shall be installed according to manufacturers instructions and according to the Florida Building Code. Provide all accessories for complete operable installation and coordinate with construction of brick hearth , decorative wood mantle and custom chimney cap.
END OF SECTION 10350
10350-2
Rev. 10/08
071900
Russell Haven of Rest Funeral Home SECTION 10520 FIRE EXTINGUISHERS AND CABINETS
PART 1 - GENERAL: 1.1
DESCRIPTION: A.
1.2
Provide and install fire extinguishers and cabinets at locations indicated on the Drawings.
SUBMITTALS: A.
Refer to Section 01300, Submittals.
B.
Provide cut sheet showing rough opening requirements, finishes and technical data for extinguishers.
PART 2 - PRODUCTS: 2.1
2.2
ACCEPTABLE MANUFACTURERS: A.
Larsen
B.
J. L. Industries.
MATERIALS: A.
Extinguisher: MP 10 series. UL Rating 4A-60 B:C.
B.
Cabinet: Semi-recessed (rolled edge) Larsen 2712-RL.
C.
Finish: Stainless Steel, 304, #4.
D.
Doors: Vertical Duo, Stainless Steel, #4 Finish.
E.
Wall bracket hangers: 1007
PART 3 - EXECUTION: 3.1
INSTALLATION: A.
Provide necessary rough opening. Ensure cabinets are plumb and properly anchored.
B.
Install cabinets as per manufacturer's suggested procedure. Test and tag extinguisher prior to installation. 10520-1
Rev. 10/08
071900 C.
Russell Haven of Rest Funeral Home Verify that all extinguishers are correctly sized and located. Provide tagging and full charging of all extinguishers.
END OF SECTION 10520
10520-2
Rev. 10/08
071900
Russell Haven of Rest Funeral Home SECTION 10800 TOILET ACCESSORIES
PART 1 - GENERAL: 1.1
1.2
DESCRIPTION: A.
Furnish and install toilet accessories as indicated in this Section and on the Drawings.
B.
Provide products of the same manufacturer for each type of accessory unit and for units exposed in the same areas unless otherwise acceptable to the Architect. Stamped names of labels on exposed faces of units will not be permitted.
SUBMITTALS: A.
Refer to Section 01300, Submittals.
B.
Submit manufacturer's technical data and installation instructions for each toilet accessory. Transmit copies of installation instructions to the installer.
PART 2 - PRODUCTS: 2.1
MANUFACTURER: A.
Approved manufacturers: 1. 2. 3. 4.
2.2
Bobrick Bradley Charles Parker Watrous
PRODUCTS: A.
Provide the following products in quantities indicated on the Drawings: 1. 2. 3. 4.
Side Grab Bar: Bradley 832-001-42"-2, 42" long bar, concealed mounting, safety-grip finish. One (1) per handicapped toilet. Rear Grab Bar: Bradley 832-001-36"-2, 36" long bar, concealed mounting, safety-grip finish. One (1) per handicapped toilet. Toilet Paper Holder (TPH): Bradley 5126. Surface-mounted, single roll dispenser. One (1) per handicapped toilet. Soap Dispenser (SD): Bradley 6542. Surface-mounted tank type. One (1) per handicapped toilet.
10800-1
Rev. 10/08
071900
Russell Haven of Rest Funeral Home
PART 3 - EXECUTION: 3.1
INSPECTION: A.
3.2
Examine the areas and conditions under which toilet accessories are to be installed.
INSTALLATION: A.
Provide wood blocking for all accessories prior to installing gypsum board.
END OF SECTION 10800
10800-2
Rev. 10/08
